Special repair work of General Toilet, Corridor of Block B, C and Ancillary Block at Haryana Bhawan New Delhi. (RECALL)

Amount

Finishing walls with Acrylic Smooth exterior paint of required shade: 1) Old work (Two or more coat applied @ 1.67 litre/ 10 sqm) on existing cement paint surface [New HSR 30.37.1] [Labor Rate]

Dismantling cement conglomerate / terrazzo floors 25 mm to 50 mm manually/ by mechanical means and disposal of material within standard lead as per direction of Engineer- in-charge [New HSR 5.42]

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. [New HSR 5.44]

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. [New HSR 9.57.2] 2) 110 mm diameter

Providing and fixing on wall face Unplasticised - PVC moulded fittings accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 1 O mm gap for thermal expansion. [New HSR 9.58.1.2] 1) Coupler 110 mm

Providing and laying of screed of 50 mm thick cement concrete 1 :8:16 to be laid below the topping. [New HSR 10.4]

Laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 :4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-charge. 1) Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. [New HSR 10.49.1] [Labor Rate] (Granite Supplied by the Deptt.)

Laying granite stone in all shades 15mm to 18 mm thick in skirting /dado, risers of steps, pillars and wall facing, laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1 :3 and jointed with white cement slurry mixed with pigment to match the shade of Granite including labour for fixing cramps pins and dowels etc. [New HSR 10.51] [Labour Rate] (Granite Supplied by the Deptt.)

Laying 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1 :3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. [New HSR 10.58] [Labor Rate] (Tiles Will be Supplied by the Deptt.)

Laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1 :4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. [New HSR 10.60] [Labor Rate] (Tiles Will be Supplied by the Deptt.)

Pointing on tile brick work with cement mortar 1 :3 (1 cement : 3 fine sand): 1) Flush/ Ruled/ Struck or weathered pointing. [New HSR 11.26.1]

Applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete [New HSR 11.58] [Labor Rate]

Fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : 1) for Fixed portion [New HSR 12.157] a) 12.157.1.1) Anodised aluminium (anodised transparent ordyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

b) 12.157.2.1) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. 2) Pre-laminated particle board with decorative lamination on both sides [New HSR 12.158.2]

Fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-charge. 1) Anodized (AC 15 ) aluminium [New HSR 12.167.1] (Labour Rate)

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. [New HSR 30.22]

Distempering with 1st quality acrylic distemper (Ready mix) having voe content less than 50 grams/ litre of approved brand and manufacture to give an even shade: 1) Old work (one or more coats) [New HSR 30.25.1] [Labour Rate)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: 1) One or more coats on old work [New HSR 30.28.1] [Labour Rate)

Removing of Malba from the campus of Haryana Bhawan & Dumping it to the dumping yard outside Municipal limit & as per the direction of Engineer-in-Charge. [NS]

Note:- In case of any difference in the unit & nomenclature of any of the HSR items of Civl, PH work depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable.

Rohit Kumar

Amarjeet Contractor