752843 ADDN ALTN CUM SPECIAL REPAIR TO CERTAIN MD ACCN INCLUDING OFFR JCOs Ors AND MES KEY PERSONAL ACCN AT MHOW

Amount

SCHEDULE "A" :

Item No 01 : M & L for Roughening / taking down existing roof treatment surfaces including plaster over old concrete roof by picking, sweeping clean and washing down with water to remove dust etc. all as specified and directed.

Item No 02 : M & L Brushing neat cement slurry with 3 Kg of cement per Sqm for bonding of old concrete surface to new concrete/plaster surfaces complete all as specified and directed.

Item No 03 : M & L Cutting out cracks to 6 mm wide 'V' section in existing roofs or terrace (if cracks > 2.5 mm wide), cleaning out, wetting, grouting with and including chemical compound SUPER LATEX of DR. FIXIT of PIDILITE INDUSTRIES LTD or SBR LATEX of STP LTD,, water and cement Sand slurry in the proportion of (1:3) by weight mix or as per manufacturers instructions all as specified and directed complete.

Item No 04 : M & L PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) mixed with integral waterproofing chemical PIDIPROOF LW of DR FIXIT of PIDILTE INDUSTRIES LTD or STP No. 1 (LIQUID) of STP LTD @ 200 millilitre per 50 Kg per cement, as in padding on roof surface for correcting / making proper slope on roof, and finishing the surfaces fair and even without using extra cement complete all as specified. Note:- Liquid WPC shall be measured and paid separately.

Item No 05 : M & L 10 mm thick rendering in CM (1:3) mixed with integral water proofing chemical compound PIDIPROOF LW of DR FIXIT of PIDILITE INDUSTRIES LTD or STP No 1 (liquid) of STP Ltd @ 200 mililitre per 50 Kg cement as per manufacturers instructions over concrete surface and finishing the surface fair and even without using extra cement complete all as specified.Note:- Liquid WPC shall be measured and paid separately.

Item No 06 : Supply only liquid water proofing compound.Make:- SUPER LATEX or DR. FIXIT of PIDILITE INDUSTRIES LTD and PIDIPROOF LW of DR FIXIT of PIDILITE INDUSTRIES LTD or equivalent make as approved by HQ CECC.

Item No 07 : M&L Water proofing treatment on "Non approachable / non accessible roof" surface (Horizontal & Vertical surfaces) in following sequence through authorized applicator of the manufacturer all as specified and directed complete. (i) Cleaning of new rendered surface properly and drying the surfaces. (ii) Applying a coat of oxidised bitumen based solvent primer @ 0.30 Kg/ Sqm. (iii) Laying 3 mm thick APP modified water proofing membrane with 100 mm over laps sealed and bounded to the surfaces by 'torchon' method. (iv) Applying two coats of bitiminous aluminium pait @ 200 Gram / Sq M (minimum) in two coats. Make incorporated : HYPERPLUS of IWL (INDIA) LTD or equivalent in Pidilite industrries Ltd / STP Ltd all as specified and as manufacturer instruction complete.

Item No 08 : M & L for plain aluminium sheeting 0.56mm thick bright finished bent/cut to shape ( for covering parapet top, side of roof projection and other similar works) fixed with flat aluminium 10 x 2 mm and screw PVC raw plug @ 300 C/C distance complete all as specified and as directed by GE.

Item No 09 : Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specially provider all as specified and directed..

Item No 10 : M&L for PCC 1:5:10 type E-2 using 40mm graded stone aggregate as in sunken floor and mass concrete complete all as specified and directed

Item No 11 : Dismantling PVC water tanks Exc 250 ltrs but not 500 ltrs including taking down of float valve and removing from site complete all as specified and directed..

Item No 12 : Dismantling water tanks and removing to store Capacity of tank exc 500 and nexc 1000 litres all as specified and directed.

Item No 13 : S&F 500 Ltrs capacity rotational moulded polyethylene water storage tanks, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-1991 complete all as specified and directed..

Item No 14 : S&F 1000 Ltrs capacity double layer (ISI marked) rotational moulded polyethylene water storage tanks, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I complete all as specified and directed..

Item No 15 : S&F in repair ball valve/float ball high pressure of PTMT 20mm with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed minimume weight 210 gm etc all as specified and directed.

Item No 16 : Taking up or down existing steel tubing and connection complete for following sizes all as specified and directed.:-

(a) 15 mm dia

(b) 20 mm dia

Item No 17 : Supplying, fixing, jointing and testing galvanised steel water tubing medium grade with all fittings such as bend, elbow, socket reducer etc fixed to walls and ceilings or laid in floors, complete for the following sizes all as specified and directed.: -

(a) 15mm dia bore

(b) 20 mm dia bore

Item No 18 : Dismantling of floor hearth or wall tilling including cement mortar bedding (but not backing) and rubbish of the premisses complete all as specified and directed.

Item No 19 : M&L non skid/mat finish ceramic colour tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm (Colour and design of tiles as approved by GE), in floors etc, and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Item No 20 : M&L glazed ceramic coloured tiles size 300mm x 450 mm x 6-7 mm thick (Colour and design of tiles as approved by GE) on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

Item No 21 : M&L non skid/mat finish ceramic colour tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.18 sq m but not exceeding 0.38 sqm (Colour and design of tiles as approved by GE), in floors etc, and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Item No 22 : M & L for vitrified cerameic tiles 9 to10mm thick light shade (square/rectangular ) polished, area of each tiles not exceeding 0.36 sqm in floor/skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed in cement mortar 1:4 complete all as specified and directed.

Item No 23 : Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed

Item No 24 : M&L Granite 20 mm thick(of any type) work (table rubbed and polished) for wall lining (Veneering to wall) and laid on cill of parapit wall over and including 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite colour Red or brown as per direction of GE

Item No 25 : M & L 22 - 25 mm thick machine cut Kota stone slab in flooring or treads single piece of steps over and including 15mm thick screed bed in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing complete all as specified and as directed. Note:- The size of Kota stone slab shall not less than 550 mm x 550 mm cut size, except the location where the balance portion remain less than size as specified above.

Item No 26 : Description same as per item No 24 above but as in skirting or vertical surfaces including 10 mm thick rendering in cement mortar 1:4, complete all as specified and as directed.

Item No 27 : Taking down chowkhats or frames not exc 1.5 sqm each without taking off shutter from the frame complete.

Item No 28 : Taking down chowkhats or frame exc 1.5 sqm but not exc 4 sqm with shutter (without taking off shutter frome the frame ) all as specified and directed.

Item No 29 : S & F 125 x 60 mm size Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,hold fast includ etc., complete as specified

Item No 30 : S & F 105 x 60 mm size Pressed steel frames for door with one or more rebates including necessary lugs, hinges, lock strike plate,hold fast include etc., complete as specified

Item No 31 : All as per item No 30 above but steel frames of size 75x60mm, complete all as specified as directed

Item No 32 : M&L for PCC (1:3:6) type C-1 with using 20mm graded stone aggregate as in bed blocks, coping, for fixing holdfast/lugs,filling hollow space of pressed steel door frame etc including necessary form work all complete as specified and as directed.

Item No 33 : M & L 2 nd class hard wood 35 mm thick Plain , framed panelled shutters ( any number of panels), with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkats complete all as speciifed and directed.

Item No 34 : S & F 2 nd class hard wood 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass , gauze, etc, (without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) fitted to chowkats complete all as specified and directed. Note :- Glass pane and wire mesh shall be measured and paid separately in respective supply only item.

Item No 35 : S & F PVC solid factory made door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete.

Item No 36 : S & F factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as shown in SSR Part – II 2004 and as directed by GE/Engineer-in-Charge.

Item No 37 : S & F 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete .

Item No 38 : S & F aluminium 200 mm long anodised barrel tower bolts ISI marked of extruded section and fixed complete.

Item No 39 : S & F aluminium 150 mm long anodised barrel tower bolts ISI marked of extruded section and fixed complete.

Item No 40 : S & F 150 mm size aluminium handles cast type, anodised ISI marked complete

Item No 41 : S & F 250 mm aluminium alloy, anodised sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete.

Item No 42 : S & F 300 mm mild steel, ordinary rat tail rod pattern spring including roller and roller plate complete fixed to steel frame / wooden frame including necessary welding, cutting, opening of wall for fixing bracket and making good complete.

Item No 43 : S & F in repair powder coated aluminium door seal 30mm wide and length as per requirement of site including dust/insect arrestor complete all as specified and directed.

Item No 44 : S & F Powder coated aluminium sliding glazed windows with three track shutter sliding (two shutters glazed and one shutter wire mesh) shall be two part as upper patr shall be three movable shutter and lower part consist three shutter (one openable in centre and both side fixed type shutter with frosted glass) with following specification and making good the adjacent side of jombs of windows by plastering in CM 1: 3 even and smooth complete etc . shifting of existing cooler stand where required complete all as specified and as directed by Engr-in-charge. (i) Windows frame of cross section 101mm x 44mm x 1.5mm thick. (Min) (ii) Three way track for sliding shutters of cross section 91.8mm x 31.75mm x1.1mm thick.(Min) (iii) Sliding shutter frame of cross section 40 x 18 x 1mm thick.(Min) (iv) 4 mm thick glass superior quality.(Min) (v) IDPE Rubber guasket for fixing of glass. (vi) Locking cleats per shutter -01 Nos.(Min) (vii) Sliding rollers per shutter - 02 Nos.(Min) (viii) Stainless steel wire cloth 0.30mm nominal dia of wire and average width of aperture 1.40mm for shutters 01 Nos. (Ix) fixing screw for frame with wall per windows- 08 Nos.

Item No 45 : S & F powder coated aluminium ventilator cross section conforming to IS 63.5x38.10x1.5mm consisting of two partions upper portion shall have louvers with 3mm thick pin headed glass and aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56m fixed with aluminium beads and securing on outer face of frame and lower portion of ventilation shall be fixed with 3mm thick pin headed glass with IDPE rubber gasket including aluminium beads, including preparation of jombs all around in CM 1:3 finishing even and smooth complete all as specified and directed.

Item No 46 : M&L mild steel framed work such as grills , gratings, etc., with ends of bars shouldered and/ or riveted, or forged in to spikes; framed guard bars ; barred iron doors; ladders; framed balusters ; walk ways ; railings; frame work of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified.

Item No 47 : S& F 18/19 mm thick Block boards, grade 2 quality, interior grade, commercial type, conforming to IS fixed with screws timber frame work as in cupboard , wardrobe etc.

Item No 48 : M & L 0.9 mm thick Decorative laminate type 1, of surface finish, colour and pattern as approved, conforming to IS fixed with approved adhesive over 18/19 mm thick plywood as per manufacturer's instructions complete all as directed and specified.

Item No 49 : Blank

Item No 50 : M & L 2nd class hard wood n.exc 6 sq.cm Plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads.complete all as directed and specified.

Item No 51 : Blank

Item No 52 : S & F 125 mm length Hasp and staple, mild steel, wire type stove enemelled black , including bolt to hinge plate and fixed with screws complete all as specified and directed.

Item No 53 : M & L for preparation old painted surfaces of steel and iron work of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Item No 54 : M & L Preparation of New wood or previously untreated surfaces of any description , not otherwise description, over 10 cm width or grith apply two coat of synthetic enemel paint (ordinary tint) over a coat of pink primer complete all as specifed and directed.

Item No 55 : Hacking out old broken glass pane (any thickness , size, quality or description) from steel frame glazed with putty or fixed with beads.

Item No 56 : M & L for 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc. 0.5 sq m in each pane.

Item No 57 : M & L for 3 mm thick figured glass ordinary quality and glazing with oil putty in square not exc. 0.5 sq m in each pane.

Item No 58 : Blank

Item No 59 : Demolition of Brick work built in cement mortar including all quoins arches pillars etc complete all as specified and directed

Item No 60 : M&L Brick work with sub class 'B' modular brick straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed

Item No 61 : M & L for reparing of RCC projection, chajjas,roofs,facia, colum etc by necessary preparation i.e scrapping ,cutting,chiseling,derusting and cleaning exposed reinforecement, surfaces of damaged, loose RCC surfaces and applying one coat of rust remover by brushing to rusted reinforecemnt to remove loose rust particles and allow to dry it for 2 to 3 Hrs , insert the new reinforcement to damaged portion by drillig hole at required distance , fill the epoxy in to the hole by 2/3 of the hole and insert the reinforcement in the hole, and binding the reinforcement at rusted portion of reinforcement, apply cement slurry on entire damaged area , and plaster the surfaces with cement , sand and Polymer liquid in 1: 3 : 15% of cement by weight ) and water as required , mixing properly and plaster the surface , finished even and smooth by making the edge water dropping groves complete all as specified and directed. Note : - Cost of formwork shall be deemed to be included.

Item No 62 : M&L for rendering in cement mortar (1:6) 10mm thick first coat on fair faces of brick walls or concrete surfacesand in cm 1:4 5mm thick second coat over first coat , mixed with water proofing compound as per manufacturer instructions, finishe fair and even without using extra cement all complete as specified and as directed including taking down existing plaster all as specified and directed.

Item No 63 : Blank

Item No 64 : M&L for rendering 10mm thick plastering in CM (1:6) finished even & fair including taking down existing plaster all as specified and directed..

Item No 65 : M&L for rendering 5mm thick in CM 1:3 as in soffits of ceiling and Rcc cjhaja/ Facia roof projections finished fair & even including taking down plaster all as specified and directed.

Item No 66 : M&L for applying three coats of white washing on new plastered surfaces of ceiling including preparation complete all as specified and as directed.

Item No 67 : M & L preparing old decorated plaster or un-plastered surfaces of ceiling and applying one coat of white wash complete all as specified and as directed.

Item No 68 : M & L Preparing newly plastered or unplastered wall surfaces all as specified and directed.

Item No 69 : M&L for applying two coats of cement base paint on new plastered surfaces of wall including preparation complete all as specified and as directed.

Item No 70 : M&L for preparing of old surfaces of walls and applying one coat of cement base paint all complete as specified and directed.

Item No 71 : Complete removal of old treatment on internal surfaces of wall by scrapping , and washing etc all as specified.

Item No 72 : M&L for applying 2 mm Avg thick wall care putty on wall on internal old/new wall surfaces as per manufacturerer instruction complete all as specified and as directed

Item No 73 : M & L for applying two coats of oil bound distemper over a coat of primer on prepared wall putty surfaces of internal wall all as per specified and directed.

Item No 74 : Demolition of cement concrete (un reinforced) in ground floor and paving n. exc. 15cm thickness (below or above ground level.

Item No 75 : M&L for PCC 1:3:6 type C2 using 40mm graded aggregate 75mm thick as in plinth protection, finished concrete surfaces even and smooth without using extra cement

Item No 76 : S & F in repairs Sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes coupling , including bedding in cement mortar to dwarf wall or including fixing cantiliver brackets and connecting union to pipe overall size 915 mm x 460mm bowl size 410 mm x 330 x 160 mm complete all as specified and directed.

Item No 77 : S & F in repairs vitreous china wash hand basin white, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of tap, waste fitting etc complete.. Note :- Pillar tape shall be measured as supply only under respective item

Item No 78 : Supply only 15 mm dia bore pillar tap cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ with long screwed shanks and fly-nuts, screwed for iron pipe complete but fency type all as specified and directed.

Item No 79 : S & F in repair vitreous china squatting pan “ORISSA PATERN” of size 580 mm x 440 mm, white, with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and directed.

Item No 80 : Supply only10 Ltr capacity,PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with and including 32 mm dia PVC flush pipe complete all as specified and directed. Note:-Fixing only rate is included in item No 79 above.

Item No 81 : Supply only PVC connection pipe 15 mm dia 450 long with PTMT nut at both ends complete.

Item No 83 : S & F (in repair) brass chromium plated angle cock 15 mm dia screwed for iron pipe or brass ferrule, complete. Make : Plumber Cat No FLP-0507/Prayag Cat Part No 7810/ Jaquar Cat Part No CQT-23059 complete all as specified .

Item No 84 : S & F in repair brass chromium plated towel rail 20 mm outer dia Bracket type, 60 cm long between flanges with and including chromium plated brass screws and wooden / plastic cleats, complete. Make : Plumber Cat part No U-0911/Prayag Cat Part No BA-10/Jaquar Cat Part No AQN-7711 complete all as specified and directed.

Item No 85 : S & F in repair over head shower with arm & flnge of chromium plated with or without swivel joints, any size, including fixing to 15mm dia steel pipe for required length or union Make: Plumber Cat part No.ITP-2401/Prayag BOS-90 Cat Part No SHP-524/Jaquar Cat Part No OHS 1989 complete all as specified and directed

Item No 86 : S&F in repair 15 mm dia consealed type stop valves, cast copper alloy, chromium plated, screwed down, high pressure with handle, screwed both ends for iron pipe or union complete all as specified and directed

Item No 87 : S&F 15mm dia Bib tap chromioum plated with crutch or butterfly handle sorewed down screwed for iron pipe or for brass ferrule and fixedcomplete.. Make : Plumber Cat part No FLP-0203 /Prayag- PIS-08, Jaquar Cat No CON-107KN complete all as specified and directed.

Item No 88 : S&F in repairs powder coated steel peg set having 06 Nos spikes fixed to wall complete all as specified and directed (Make as spproved by GE)

Item No 89 : S & F in repair PVC bath cabinet box mirror type with shutter complete. (Make :- Prayag Cat No -551 or equilent of plumber/ESS/jaquar etc.)

Item No 90 : Blank

Item No 91 : S & F in repair corner shelf of 300 mm size with ABS brackets complete. Make : Prayag Cat No - BEA - 52 or equiilent of Jaquare CAT NO - CAN-1173/Plumber CAT NO- U-0921 complete all as directed and specified.

Item No 92 : S & F in repair CP Thumbler Holder, complete all as specified and directed by Engineer-incharge. MAKE:- Plumber Cat Part No. U-0914/ Prayag Cat Part No BA-16/ Jaquar cat Part No-AQN-7741

Item No 93 : Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets of any thickness, including cover fillets complete.

Item No 94 : M&L false ceiling with GI powder coated frame work and 4mm thick, white pre-premiered and painted self embossed, reinforced designer board conforming IS- 14862 and ISO-8336, duly suspended with ceiling complete all as specified and directed by Engr-in-charge.

Item No 95 : S & F in repair Gun-metal, globe of gate valve /flush cock of 20mm bore with iron wheel head, screwed both ends for iron pipe etc all as specified.

Item No 96 : S & F in repair PVC (SWR) nahani trap with grating having diameter of outlet 75 mm including joining to waste pipe with solvent cement complete.

Item No 97 : S & F in repair 110 mm dia bore. PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in floor/ trenches complete all as specified and directed.

Item No 98 : S & F in repair 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in floor/ trenches complete all as specified and directed.

Item No 99 : S & F in repair 110 mm dia bore. PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to walls complete all as specified and directed.

Item No 100 : S & F in repair 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls complete all as specified and directed.

Item No 101 : S & F in repair 110 mm dia bore PVC (SWR) bends with acess door any radius with solvent rubber ring joints, fixed complete all as specified and directed.

Item No 102 : S & F in repair 75mm dia bore PVC (SWR) bends with acess door any radius with solvent rubber ring joints, fixed complete all as specified and directed.

Item No 103 : S & F in repair 110 mm dia bore PVC (SWR) junction single, single (T) equal or unequal with acess door with solvent rubber ring joints, fixed complete all as specified and directed.

Item No 104 : S & F in repair 75mm dia bore PVC (SWR) junction single, single (T) equal or unequal with acess door with solvent rubber ring joints, fixed complete all as specified and directed.

Item No 105 : S & F in repair 110 mm dia bore PVC (SWR) branch piece single (single Y) equal or unequal with rubber ring joints, fixed complete all as specified and directed.

Item No 106 : S & F in repair 75mm dia bore PVC (SWR) branch piece single (single Y) equal or unequal with rubber ring joints, fixed complete all as specified and directed.

Item No 107 : S & F in repair 110 mm dia bore PVC (SWR) vent cowl rubber ring joints, fixed complete all as specified and directed.

Item No 108 : Demolition of reinforced cement concrete of any description for manhole cover, slab of septic tank & soak well etc complete.

Item No 109 : M & L providing pre-cast cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slab of manholes, septic tank, soak well etc set in cement mortar 1:4 with plain fair faces including chamfered weathering, throating etc including necessary use and waste of form work complete all as specified and directed.

Item No 110 : S & F mild steel TMT bars 10 mm dia and over as in reinforcement, cut to length, benty shape required including cranking, bending, spirally for hooping for columns, hooking ends and hinding with mild stee wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Item No 111 : Surface excavation n. exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type soil complete all as specified and directed

Item No 112 : M&L Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

Item No 113 : M & L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in mas concrete complete all as specified and directed.

Item No 114 : M & L 60 mm thick Machine pressed precast concrete interlocking paver blockfixing with grey cement and pigments OF " I " shape or as approved by GE ,and any colour and size confirming to IS 15658-2006 of M-35 Grade set , laid over 50 mm (average) thick dust sand cushioning,filling of joints with sand & compaction using surface vibrator after filling of joints lain in any pattern as decided by Engineer-In-Charge including packing of sides by cement concrete finishing surfce even and smooth complete all as specified and as directed. Note : Sand cushioning shall be measured and paid separately .

Item No 115 : S & F Joist channel, angle or tee, square or rectangular tubler sections fixed independently or as purlin, rafter or post incl cutting to dead length where required notching drilling firing riveting and/or welding or connecting with bolts and nuts providing and fitting angle cleats fish plates, gusset plates etc complete all as specified and directed (Fe-410-W (gde-E-250) quality A)

Item No 116 : Treating the soil under the plinth protection at the rate of 5 litre of emulsion per square metre of surface area.complete all as directed and specified.

Item No 117 : S & F Pre-painted galvalum aluminium zinc coating steel based corrugated steel sheet 0.50mm thick (total coated thickness) of any colour having tensile strength of 550 Mpa minimum, yeild strength, it shall be coated with hot dip alloy of 55% aluminimum, 43.5% zinc,1.5% Silicon and finished with resin coat on both surface @ 150 gm/ sqm of coating as specified and shall be fixed with hot dip galvanised, self drilling and self tapping screws neoprened and EDPM washers as in roof covering all as directed at site all as specified and directed..

Item No 118 : M&L for preparation old decorated surface of wall/ceilling to be done by mechanical means/smart painting technique coats of acrylic latex base exterior grade (100% ACRYLIC) over a coat of primer at any height including necessary scaffolding complete alongwith five year warrantly complete all as specified and directed. Note:- 1. Painting work shall be executed through authorized and certified applicator of paint manufactures of paint companies. 2. Approval shall be obtained from GE for make/manufacturers and applicator before engagement in the work. 3. Contractor shall provide five year written guarantee certicate for the paint work.

Item No 119 : M&L for applying one coat primer acrylic polymer modified water proofing coating (Brushband of FOSROC or equivalent) and over that two coats of acrylic polymer modified two component elastometric water proofing membrane coating (Brush band of Fosroc or equivalent) complete all as specified as per manufacturers instruction as directed (Make :- Dr Fixit, Fosroc, Sika) . Note :- 1. This item shall only be executed through level 4 or level 5 certified and authorized applicator of the company. 2. A warranty for 5 years in the form of written agreement shall be submitted by the contractor. 3. The rate quoted by the contractor shall include all the provisions mentioned in this item including notes.

Item No 120 : M&L Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified.

(a) 16mm dia bore

(b) 20 mm dia bore

Item No 121 : S & F of CPVC brass elbow (3/4" X ½") for 20 mm outer dia CPVC pipe complete all as specified and directed.

Item No 122 : S & F of CPVC Male Brass Threaded Adaptor (MTA/ MBTA) for 20 mm outer dia pipe complete all as specified and directed.

Item No 123 : S & F of CPVC Tank Adaptor for 20 mm outer dia pipe complete all as specified and directed.

Item No 124 : S & F of CPVC union for 20 mm outer dia pipe complete all as specified and directed.

Item No 125 : S & F of CPVC Ball Valve for 20 mm outer dia pipe complete all as specified and directed.

Item No 126 : Taking Down shutters of any description exc 1.00 sqm and n.exc 2.00 sqm each incl removal from site all as specified

Item No 127 : M & L cutting chases in brick wall for concealed water tubing, pinning in, making good of facings where required and pointing in cement mortar 1:3 to ends or edges etc, cutting not exceeding 10 cm width or girth, complete.

Item No 128 : M & L Preparation of old painted wooden surfaces of any description not otherwise description over 10 CM width or grith and apply one coat of synthetic enamel complete all as directed.

Item No 129 : Dismantling boarding of any description fixed in any position with screws all as specified and directed.

Item No 130 : M&L for 6mm thick Plywood, grade BWR, type BB, fixed with Nails to timber frame work all as specified and directed.

Item No 131 : Extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick, fixed with nails all as specified and directed.

Item No 132 : Blank

Item No 133 : S&F cast iron or MS Drawer pulls, 3 screw plate with fixed dished pull; 80 mm to 100mm long

Item No 134 : S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed.

Item No 135 : S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts;

Item No 136 : S&F 300mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

Item No 137 : S&F 100 mm size of Butt hinges, medium weight cold rolled mild steel complete door etc

Item No 138 : M&L for floor door stopper of brass body and tongue, anodised, with hard drawn steel spring, 140mm long, fixed in floor complete all as specified

Item No 139 : S&F hasp and staple 125mm, safety type, aluminium anodised with alu hinge pin incl bolt to hinge plate and fixed with screws

Item No 140 : M & L in fixed in repairs 18/19 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, as in doors fixed with screws to timber frame work complete all as specified and directed.

Item No 141 : M & L in fixed 18/19 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, as in doors fixed with screws to timber frame work complete all as specified and directed.

Item No 142 : M&L for stainless steel wire cloth, 0.71mm nominal dia of wire and average width of aperture 1.20mm and fixed with tinned tacks, or stainless steel wire staples

Item No 143 : Providing and fixing fixed louvers fabricated from Roll formed sections made of galvanized Steel colour coated/powder coated (base Steel as per IS 513 ‘D’ quality, galvanized as per IS 277 with zinc of 120 grams/Sqm) with thickness of 0.58mm coated sections to be primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder up to 50-60 microns thick, section for external frame 33 x 58 mm, glass holding flanges made of polypropylene, sections are to be cut to length, mitre joined with corner bracket. The above frames should be fixed to the concrete/masonry walls by means of self expanding screws incl window glass 4mm thick.

Item No 144 : Providing and fixing of double rebate openable/fixed windows made of galvanized steel colour coated/powder coated (base steel as per IS 513 of “D" quality, galvanized as per IS 277 with zinc of 120 grams/sqm) with total thickness of coating 0.58 mm, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, outer frame section 72 x 55 mm, centre mullion section 72 x 50 mm, shutter section 47 x 20 mm,fly mesh section 40 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consists rebate for glazed shutter, fly mesh and 20 mm provision for guard bars/grills, the sections cut to length mitre joined with corner bracket, centre mullions fixed with mullion cap, stay, handles, latch, 2 Nos of heavy duty stainless steel pivot hinges per shutter and panelled with 5mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade), fitted using EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing windows in the concrete/masonry wall by means of self-expanding screws, including 10mm Square bars welded to 6x12mm flat at a distance 150mm c/c (pitch) etc. complete as per the direction of Engineer in Charge.

Item No 145 : M&L for demolition of Precast concrete articles and precast concrete block walling set in any type of mortar

Item No 146 : Providing precast cement concrete 1:2:4 type B0 (12.5mm garded aggregate) jallies, 40mm thick,including all moulding and set in CM 1:4 complete all as specified.

Item No 147 : Treating soil along the external perimeter of the building at the rate of of 2.25 ltr per running meter surface area

Item No 148 : Treatment of soil under existing floors using emulsion @ one ltr per hole 300mm apart including drilling and plugging 12mm dia holes to match the existing floors with cement mortar 1:2

Item No 149 : Forming construction dummy joints 65mm deepx10mm wide fillied with Grade B sealing compound

Item No 150 : All as per item No 22 above but as in skirting/ dado etc surfaces of wall complete all as specified and as directed.

Item No 151 : Mirror polish on kota stone where ever required to give high glossy finish over exciting floor all as specified and directed.

Item No 152 : M&L for Cement concrete tiles 20cm x 20cm x 20mm thick, machine pressed; set jointed and pointed in neat cement slurry as on roof surface with grey cement and pigments, and cut and polished etc incl 15mm thick cement plaster in CM 1:4, complete all, as specified and directed by Engr-in-charge

Item No 153 : Rounding to edges of stone slab slab one edge such as in steps,cooking platform,and other similar situation complete all as specified and directed.

Item No 154 : S&F in repair 25mm dia Gun-metal, golbe or gate valves, with iron wheel head, screwd both ends or iron pipe and fixed all as specified and directed.

Item No 155 : S&F 15 mm bore long body CP Bib taps, cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed all as specified and directed.

Item No 156 : Taking down old GI tubing ISI marked medium grade 25mm bore with all fittings including connection etc, complete all as specified.

Item No 157 : M&L for GI tubing ISI marked medium grade 25mm bore with all fittings and fixed complete to walls and ceiling or laid under floor including connection etc, complete all as specified.

Item No 158 : M&L for 25mm dia Ball Brass valves high pressure with polythene float and fynut complete screwed for iron pipe or brass ferrule and fixed all as specified and directed.

Item No 159 : Blank

Item No 160 : S & F in repair 75mm bore PVC (SWR) vent cowl complete all as specified and directed.

Item No 161 : Dismantling of cast iron/PVC pipes jointed in cement mortar 110 / 75 mm bore all as specified and directed

Item No 162 : S&F 75mm PVC reducers PVC (SWR) all as specified and directed.

Item No 163 : S&F110mm PVC reducers PVC (SWR) all as specified and directed.

Item No 164 : S& F as in repair 40mm Bottle trap of PTMT having minimum water seal of 25mm .(Minimum weight 32mm-260gms/ 40mm-270 gms) all as specified and directed.

Item No 165 : S&F in repair Waste coupling of 40 mm dia PTMT (half or full threaded) . (Minimum weight 32mm-45gms/40mm-60 gms) fixed in repair complete all as specified and directed.

Item No 166 : S&F PVC waste pipe fixed to any type of coupling of 40mm threaded complete all as specified and directed.

Item No 167 : M & L for repair to sunken floor by provide water proofing treatment to sunken floor surfaces of RCC slab by the following specifications as specified and directed :-(a) Provide PCC 1 : 1.5 : 3 type A with using 12.5mm graded stone aggregate in slope of average thickness 50mm on sunken floor slab mixed with and including integral water proofing compound manufactured by Dr FIXIT or equivalent as approved, finish the surface even & smooth without using extra cement.(b) Rendering 15mm thick in CM 1:3 mixed with & including integral water proofing compound on sunken floor and sides of (Vertical surface) sunken portion.(c) Applying surfaces of bituminous primer (conforming to IS-3384-1965) @ 0.40 Kg/Sqm complete. on complete sunken surfaces of floor & wall and provide necessary connections to soil/waste pipe from WC/ nahani trap etc including demolation of old sunken complete all as specified and as directed. (d) applying a tack coat of Industrial bitumen grade of 85/25 at the rate of 1.2 Kg per Sqm including cleaning surfaces (1st coat for bonding material below membrane and 2nd coat on top of membrane. Each coat would be paid seperately.) (e) APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed. (Note : Floor Area shall be measured for payment).

Item No 168 : M & L for provide PVC spout pipe of 25mm bore & 45cm length in sunken floor including cutting holes in brick walls built in cement mortor and making good the dismantled portion in PCC (1:2:4), type B1 with using 20mm graded stone aggregate with wall finish at the disturbed portion of external surfaces complete as directed and specified.

Item No 169 : S&F Chromium plated jet for EWC with 1.00 Mtr long PVC pipe including necessary GI fitting as required like toe nipple etc complete all as specified and directed

Item No 170 : Complete Removal of Existing tretment on ceiling surfaces including washing rubbingdown and stopping of distempered and painted surfaces

Item No 171 : M&L for prepeparation of new plastered surfaces of ceiling and provision of 1mm thick putty and applying chalk whiting primer on new plastered surfaces ceiling and applying two coats of oil emulsion distemper

Item No 172 : M&L for prepeparation of old plastered surfaces of ceiling and provision of 1mm thick putty and applying chalk whiting primer on new plastered surfaces ceiling and applying two coats of oil emulsion distemper

Item No 173 : Complete Removal of Existing tretment on External surfaces of walls including washing rubbingdown and stopping of cement based painted surfaces

Item No 174 : M&L for two or more coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and directed.

Item No 175 : Dismantling fillets,rails,posts,rafters,purlins,etc under 40Sqcm in section all as specified and directed.

Item No 176 : Providing and fixing in true horizontal level 600mm x 600mm, false ceiling system hot dipped galvanised steel section, exposed surface with pre-coated capping, main tee of size 24 x38 mm, having 0.25mm gauge at every 1200 mm centre to centre maximum and rotary stitched cross tee of size 24 x 38 mm having 0.25 mm gauge at every 600mm c/c and sub cross tee of size 24 x 38mm, having 0.25 mm gauge at 1200 mm c/c and wall angle of size 19 x 19mm, having 0.35mm gauge fixed to the periphery of the wall. The abovegrid is suspended at every 1200 mm c/c in both directions using 2.0mm thick pre-straightened GI wire. laying ceiling tiles of approvde make and specification , of size 600mm x 60mm x 6mm all as specified and directed.

Item No 177 : Dismantling of plain or corrugated steel sheeting any gauge, thickness, including nainaital or similar pattern roof coverings.

Item No 178 : Dismantling of plain or corrugated AC sheeting including roof coverings all as specified and directed.

Item No 179 : Dismantling wrought iron or mildsteel work of any descripton of any description not otherwise provided all as specified and directed.

Item No 180 : M & L for cutting holes in brick walls built in cement mortar at the starting point of down take soil/waste pipe at any floor, fill the joint of down take pipe & trap with thick mortar in CM 1:3 and making good the dismantled portion in PCC (1:2:4), type B1 with using 20mm graded stone aggregate with wall finish at the disturbed portion of external surfaces complete as directed and specified.

Item No 181 : M & L Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates

Item No 182 : M &L for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, and eves board fixed with self tapping screws as specified

Item No 183 : Formwork to sides and soffits of coping beam finished surfases fair.

Item No 184 : M&L for mild steel TMT bars 8mm dia ,cut to length,bent to shape required,including cranking,bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

Item No 185 : M&L for RCC 1:2:4 type B1(20mmgraded aggregate) as in Chajjas all as specified and directed.

Item No 186 : M&L for cement concrete 25mm thick type B-1, 1:2:4 (12.5mm graded aggregate) as in roof top etc complete all, as specified and directed.

Item No 187 : S&F 100mm stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof

Item No 188 : S&F 75mm stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof

Item No 189 : M&L in repair PVC (SWR) gully trap 125/110 mm, setting & jointing with solvent cement

Item No 190 : S&F 40mm dia GI Tubing as in spout pipe of medium grade including cutting in any length as required and fixed to wall & floor etc complete all as specified and directed.

Item No 191 : S&F18mm thick factory made 100% solid rigid PVC (Poly Vinyl Chloride) foam sheet Prelam colour having density of 600kg/cbm manufactured by an Iso 9001-2015 certified company.Termite proof,water proof and flame retardant PVC sheet,manufactured by single layer extrusion process for one side prelaminated solid PVC foam sheet. PVC film laminate should be pasted on PVC sheet with suitable adhesive and approved shade all as specified and directed.

Item No 192 : S&F 18mm thick factory made 100% solid rigid PVC (Poly Vinyl Chloride) foam sheet Plain colour having density of 600kg/cbm manufactured by an Iso 9001-2015 certified company.Termite proof, water proof and flame retardant PVC sheet,manufactured by single layer extrusion process all as specified and directed.

Item No 193 : S & F modular type stainless steel basket size 500 mm x 530 mm x 100 mm (dia of wire not less than 3.0mm) of any shape with and including side sliding roller clip and sliding rails on both side fixed with steel screws incl all fixing arrangement complete as specified and dirceted.

Item No 194 : All as per item no 193 as above but basket size 500 mm x 530 mm x 150 mm complete as specified and dirceted.

Item No 195 : All as per item no 193 as above but basket size 500 mm x 530 mm x 200 mm complete as specified and dirceted.

Item No 196 : S&F 100mm size MS mat/glossy finish handle complete as specified and directed.

Item No 197 : S&F stainless steel self closing hinge of 75mm size for PVC door shutter complete as specified and directed.

Item No 198 : S&F 50x15mm size magnet door catcher for closing for PVC door shutter complete as specified and directed.

Item No 199 : S&F mild steel drawer cabinet channel for moving the drawer etc complete as specified and directed.

Item No 200 : S&F 40mm flaps width (when open) continuous (Piano) hinges mild steel bright finish or electrogalvanised

Item No 201 : Cutting channels, grooves or rebates n exc 15cm girth,for inserting galvalume sheet on wall and trimming surface with or without reinforcement all as specified and directed.

Item No. 202 :- Supplying, laying, jointing and testing DWC HDPE, SN-8 confirming to IS 16098 pipe of size 200 mm internal dia of pipe, laid in trenches and Jointed complete. drain pipe of size 200 mm internal dia of pipe grade 'A' confirming to IS-651-1980 laid in trenches and jointed cement mortar 1:1 including taking down existing pipe, complete all as specified and directed.

Item No 203 : S&F in repairs 25 mm dia stainless steel curtain rod as approved by GE complete all as spd and directed.

Item No 204 : S&F in repairs 25 mm dia S/S decorative brackets with arrangements as approved by GE complete all as spd and directed.

Item No 205 : S&F in repairs shelf glass assembly consisting of 5.5mm thick sheet glass,shelf 120mm wide with CP bracket guard and railing 600mm long all as specified and directed.

Item No 206 : S&F stainless steel plate rack for kitchen 1mm thick of best quality with suitable hanging arrangement and fixed to wall complete all as spd and directed by Engr-in-Charge.Note : siz of plate rack should not be less than 900x 1200mm and weight of rack shall not be less than 8.50 kg each all as specified and directed.

Item No 207 : S&F in repair CP bottle trap 32mm bore for wash basin with inlet and outlet screwed for connection including necessary packing union and cup and fixed.

Item No 208 : S&F in repairs soap dish (ovel) type mild steel chromium plated of size not less than 50mm dia complete all as specified and directed..

Item No 209 : Refixing old steel tubing and connections in new or old position walls,ceiling,floors etc.15mm dia all as specified and directed.

Item No 210 : Refixing old steel tubing and connections in new or old position walls,ceiling,floors etc.20mm dia all as specified and directed.

Item No 211 : S & F stainless steel butt hinges 100 mm long all as specified and directed.

Item No 212 : M& L ATT points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same all as specified and directed.

Item No 213 : Taking down door shutter from frame exc 1 Sqm but not exc 2 Sqm each and refixing the shutter in the same opening after easing and adjusting all as specified and directed.

Item No 214 : S & F Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (incl steel sheeting or other covering, also fastening and fixing complete all as specified and directed.

Item No 215 : S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 all as specified and directed.

Item No 216 : Excavation in trench in avg soil not exceeding 1.5M wide and not exceeding 1.5M in depth for sewage line, manhole etc not exceeding 10 sqm on plan and getting out in any type of soil complete all as specified and directed.

Item No 217 : Returning, filling in soil including spreading, watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified and directed.

Item No 218 : Removing excavated material to a distance n exc 50M and deposited where directed at a level n. exc 1.5M above the starting point complete.

Item No 219 : Demolition and breaking up drain pipe of dia 150 mm (internal dia) (salt glazed stoneware, AC or reinforced conrete) set in cement mortar complete all as specified and directed.

Item No 220 : M & L cement concrete bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate for the 150 mm internal dia of pipe complete all as specified and directed

Item No 221 : S & F in repair Bidet spray (Health faucet) with 1 meter tube and holder, complete all as specified and directed. (Make : Plumber Cat No IT - 1904 ITALIAN / Prayag Cat Part No- BEA-87 /Jaquar CAT PART NO - ALD-CHR-583)

Item No 222 : S & F in repair CP Toilet paper holder, complete all as specified and directed by Engineer-incharge. MAKE:- Plumber Cat Part No. U-0916/Jaquar Cat Part No AHS1551 /OR Prayag Cat No- BA-88 EQUILENTcomplete all as specified and directed.

Item No 223 : S&F in repair CP wall mixer, for mixing hot and cold water fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure with long screwed shanks and fly-nuts , screwed for iron pipe ISI Marked of other specified.

Item No 224 : Supply only 15 mm dia bore basin mixture brass chromium plated with capstan heads screwed down high pressure with or without letter ‘HOT’ or ‘COLD’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed. (Make : Plumber Cat part No AZT-3104/Prayag : Cat part CAT NO-8750/ Jaquar Cat Part No FLR-5167NB)

Item No 225 : S & F( in repairs) Vitreous chaina wash down water closet pan (pedestal pattern), white including pedestrial pan and trap, including seat cover for pedestial pan and connecting to drain or outgoing pipe and to flushing pipe, antisyphonage pipe etc complete all as specified and directed. Make :- Parryware (Super fine), Hindware,Johnson Pedder .

Item No 226 : Supply only ( ISI Marked) white coloured Plastic water closet seat, back, closed pattern with flat bottom , and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Item No 226(A) : in repair 15 mm bore sink mixer with swining / rotatable spout with connecting and wall flange, complete all as specified and directed.

INTERNAL ELECTRIFICATION

Item No. 227 :- Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site.

Item No. 228 :- Taking down ceiling fan/ exhaust fan/ wall fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of concerned AGE E/M complete all as specified and as directed.

Item No. 229 :- Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

Item No. 230 :- Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface complete all as specified and directed.

Item No. 231 :- Taking down existing geyser of any capacity after disconnecting all necessary electrical and water supply connections and deposit to MES store yard of concerned AGE E/M Mhow complete all as specified and as directed.

Item No. 232 :- Taking down existing single phase electric energy meter of any capacity after disconnecting all necessary electrical connections and deposit to MES store yard of concerned AGE E/M Mhow complete all as specified and as directed.

Item No. 233 :- M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One light point controlled by one, two way switch 5 Amps

(d) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(e) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

(f) One bell point controlled by one, bell switch 5 Amps

Item No 234 : Description all as per item No 233 here in before but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

Item No 235 : Description all as per item No. 233 here in before but using 4.0 sq mm single core copper conductor FRLSH cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 4.0 sq mm PVC insulated copper conductor FRLSH cable as earth continuity conductor along with wiring and connecting to the common eath dolly. (for AC Point)

Item No 236 : S & F for Modular Switch piano flush type, single pole, one way, and 5/6 Amp single module complete all as specified.

Item No 237 : S & F for Modular Switch piano flush type, single pole, one way, and 15/16 Amp single module complete all as specified.

Item No 238 : S & F for Modular Switch piano flush type, single pole, two way, and 5/6 Amp single module complete all as specified.

Item No 239 : S & F for Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

Item No 240 : S & F for Modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

Item No 241 : S & F modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

Item No 242 : S & F Bell push modular 6 Amps single module complete all as specified.

Item No 243 : S & F for lamp holder, PVC / Polycarbonate type with back plate suitable for batten/ slanting fittings complete all as specified and directed.

Item No 244 : S & F for Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ AC supply complete all as specified and as directed

Item No 245 : S & F for Modular type TV Socket out let complete all as specified and as directed.

Item No 246 : M & L for Sub main wiring with approved colour coding as per IS with four single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC FRLSH conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one runs of PVC insulated with 6 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Four runs of 6 sqmm cable, one runs of 6 sqmm cable and one run of PVC conduit will be measured as one unit.

Item No 247 : M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc. one run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit.

Item No 248 : S & F for sheet metal enclosure MCB DB TPN 4 way, IP 43, IK 09, Vertical type with 200 Amps rated bus bar 415 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed. Note :- The spaces left after inserting MCB should be properly filled with blanking plates.

Item No 249 : S & F for sheet metal enclosure MCB DB SPN 8 way, IP 43, IK 09, with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed. Note :- The spaces left after inserting MCB should be properly filled with blanking plates.

Item No 250 : S & F for MCB tripple pole and neutral rated capacity 63 Amps, 415 Volts breaking capacity 10 KA, 'C' curve and of the same make as item no. 23, complete all as specified and as directed.

Item No 251 : S & F for MCB Single pole and neutral rated capacity 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve and of the same make as item no. 23, complete all as specified and as directed.

Item No 252 : S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve and of the same make as item no. 23, complete all as specified and as directed.

Item No 253 : S & F for metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Amps including removal of old unserviceable one and of the same make as item no. 23, complete all as specified and as directed.

Item No 254 : Labour only for refixing water heater storage type (Geyser) any type obtained from taking down including 04 Nos of hold fashner nuts required suitable size fixed in brick wall and replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable 2.50 sqmm, PVC connection pipes for Cold & Hot water including over hauling geyser, painting of geyser complete with two coats synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc and writting the MES Number with synthetic enamel paint complete all as specified and as directed

Item No 255 : S & F for water heater storage type (Geyser) vertical/ Horizental type as per site requirement with inner container of capacity 25 ltrs, with glass coated heating element, electrically operated, AC 230 Volts, BEE 5 star rated (as per latest star label period), ISI marked, including 04 Nos of hold fashner nuts required suitable size fixed in brick wall, PTMT connections 15 mm size with nuts and length 450 mm including writting the MES Number with synthetic enamel paint complete all as specied and as directed. The geyser should be tough enough to withstand pressure upto 8 bars. The inner tank should have a minimum 07 years warranty submitted by the tenderer from the manufacturer. Additional warranty on models having less than 07 years will not be accepted.

Item No 256 : S & F for ceiling fan, 230 Volts, 1200 mm sweep with min air delivery 220 CFM, service value of the fan shall be greater than 8.0 as per BIS with blades, down rod & other necessary accessories and electrical connections from ceiling rose to fan teriminal without remote system, with capacitive type fan regulator complete all as specified and as directed.

Item No 257 : S & F for energy efficient exhaust fan of 300 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base including writting the MES Number with synthetic enamel paint compelte all as specified and directed. (Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted).

Item No 258 : Labour only for refixing the celing fan/ Exhaust fan obtained from taking down with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal including over hauling the fan, painting of ceiling fans complete with two coats synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc and writting the MES Number with synthetic enamel paint complete all as specified and as directed.

Item No 259 : S & F for Highly efficient LED Bulbs, 10 W, 5 star rated, used as a ready replacement for existing GLS/CFL direct fit lamp,in B-22 cap of make Jaquar, Wipro, Philips complete all as specified and directed

Item No 260 : S & F for Decorative wall mounted luminaire made out of polycarbonate with unbreakable globe suitable for LED bulb and provosion of LED bulb 10 watts, 5 star rated complete all as specified and as directed. Make Havells Cat No LHDLO6160099 or its equvalent in Jaquar, Wipro, Havells.

Item No 261 : S & F for LED tube light fitting 2 feet x 10 watts mirror type with high output diffuser, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting complete all as specified and as directed.

Item No 262 : S & F for Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed.

Item No 263 : S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and directed.

Item No 264 : S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 30 watts, lumen output >= 110 lm/W, burning hours > = 50000 Hrs, with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including 40 mm dia GI pipe 1.2 mtr long bend into size with bracke, clamps, nut, bolts complete all as directed.

Item No 265 : S & F for PVC non-metallic rigid conduit ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 20 mm dia for LAN, telephone and TV connections including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed.

Item No 266 : Supply, installation, testing & commissioning of Single Phase, 2 Wire, Pre-paid Energy Meters, BIS 15884 with Pre Payment Shock Proof capacitive touch Key pad, communication based Digital having current range 05-60 Amp, 240 V, accuracy class 1.0 along with Parallel home display split Unit, with inbuilt load control switch, containing provision for TOD & RTC, (wireless, without DCU, USB, Pen drive & Sim, no other extra equipment required for data, meter itself capable for data storage) capable to define 4 tariff slabs, happy hour & holiday definition, when user go outside of the home, via mobile app user can decrease its sanctioned load all as specified and directed. That the manufacturer or their service provider shall furnish 5 (Five) years replacement warranty for prepaid meters installed under this contract. The cost will include installation of software of the prepaid meter. (Model - Liberty 170) Make ABB, L&T, Schneider, SECURE

Item No 267 : Supply, installation, commissioning and testing indoor type LT wall mounting Panel Board of minimum size 1.50 m (height) x 1.20 m (breath) x 0.30m (depth) factory made CPRI approved panel, weather, dust & vermin proof indoor, double door, front openable, including four comparment for fixing of four Nos Three phase KWH meter, one No single phase meter and MCB TPN and providing glass view for reading of meter and providing rubber/ PVC gasket of suitable size all sides of door, with copper busbar wrapped with PVC tape/ sleeves with maintained the colour code and copper strip/ wire busbar of suitable size to MCCB input and MCCB/ MCB output of suitable length for connection of cable from main busbar, made out of 2.00 mm thick mild steel CRCA sheet with suitable size angle iron supporting frame including applying two coats of Powder coated paint over a coat of red oxide zinc chrome primer over exposed external & internal surfaces suitable for 3 phase 4 wire system 415/440 volts grade including complete internal wiring with 10 sqmm copper wire and connections of all outgoing / incomming existing cable of any size complete all as directed by Engineer-in-Charge. (For Officers G+1 Md Accn )

(c) Three Phase, 4 Wire, Pre-paid Energy Meters, BIS 15884 with Pre Payment Shock Proof capacitive touch Key pad, communication based Digital having current range 10-100 Amp, 415 V, accuracy class 1.0 along with Parallel home display split Unit, with inbuilt load control switch, containing provision for TOD & RTC, (wireless, without DCU, USB, Pen drive & Sim, no other extra equipment required for data, meter itself capable for data storage) capable to define 4 tariff slabs, happy hour & holiday definition, when user go outside of the home, via mobile app user can decrease its sanctioned load all as specified and directed. That the manufacturer or their service provider shall furnish 5 (Five) years replacement warranty for prepaid meters installed under this contract. The cost will include installation of software of the prepaid meter. - 04 Nos (Model - Liberty 370) Make ABB, L&T, Schneider, SECURE

Item No 268 : Supply, installation, commissioning and testing indoor type LT wall mounting Panel Board of minimum size 1.20 m (height) x 1.20 m (breath) x 0.30m (depth) factory made CPRI approved panel, weather, dust & vermin proof indoor, double door, front openable, including four comparment for fixing of five Nos single phase meter and MCB and porviding glass view for reading of meter and providing rubber/ PVC gasket of suitable size all sides of door, with copper busbar wrapped with PVC tape/sleeves with maintained the colour code and copper strip/wire busbar of suitable size to MCCB input and MCCB/MCB output of suitable length for connection of cable from main busbar, made out of 2.00 mm thick mild steel CRCA sheet with suitable size angle iron supporting frame including applying two coats of Powder coated paint over a coat of red oxide zinc chrome primer over exposed external & internal surfaces suitable for 3 phase 4 wire system 415/440 volts grade including complete internal wiring with 1.5 sqmm copper wire and connections of all outgoing / incomming existing cable of any size complete all as directed by Engineer-in-Charge. (For G+1 JCOs, OR Md Accn)

OUTGOING (a) MCB, Single pole & neutral, 40 amps, 240 volts, ‘C’ curve, 10 KA all complete as specified and as directed - 06 Nos (b) Single Phase, 2 Wire, Pre-paid Energy Meters, BIS 15884 with Pre Payment Shock Proof capacitive touch Key pad, communication based Digital having current range 05-60 Amp, 240 V, accuracy class 1.0 alongwith Parallel home display split Unit, with inbuilt load control switch, containing provision for TOD & RTC, (wireless, without DCU, USB, Pen drive & Sim, no other extra equipment required for data, meter itself capable for data storage) capable to define 4 tariff slabs, happy hour & holiday definition, when user go outside of the home, via mobile app user can decrease its sanctioned load all as specified and directed. That the manufacturer or their service provider shall furnish 5 (Five) years replacement warranty for prepaid meters installed under this contract. The cost will include installation of software of the prepaid meter.- 04 Nos (Model - Liberty 170) Make ABB, L&T, Schneider, SECURE

External Electric Supply / External water supply

Item No. 269 : Taking down existing old unserviceable LT UG/ service cable of any description and size complete all as specified and directed.

Item No. 270 :- Supply and laying & testing and commisioning LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of size complete all as specified and directed

(a) 50 Sqmm x 3.5 core

(b) 35 Sqmm x 3.5 core

(c) 25 Sqmm x 4 core

(d) 16 Sqmm x 4 core

Item No. 271 :- Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth for foundation etc or for shafts, wells cesspits manholes pier holes etc not exceeding 10 sqm on plan and not exceeding 1.5 m depth in soft/loose soil etc complete all as specified and directed.

Item No. 272 :- Supply and laying un-reinforced precast concrete cable cover LV, type 1 with peak of size 250 mm x 150 mm x 40 mm with minimum average breaking load 200 kg as per IS 5820:1970, ISI marked, complete all as specified.

Item No. 273 :- Supply , spread and filling for clean dry river sand in trenches/ducts for cushioning to cable, 8 cm in depth before laying the cable and 15 cm in depth after laying the cable complete all as specified. Note :- Punned thickness only will be measured and paid.

Item No 274 : S&F Tubes, 'light grade,galvanised, with all fitting of size 40 mm; laid in trenches for cable protection all as specified and directed.

Item No 275 :- M & L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part I including excavation and earthwork in any type of soil/strata and testing on completion. Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

Item No 276 : Taking up or taking down steel tubing and connections including cleaning for refixing or removal to store for the following sizes complete all as specified and directed :-

(a) 50 mm dia

(b) 40 mm dia

(c) 25 mm dia

(d) 20 mm dia

Item No 277 : Supply and laying for galvanised iron tubing medium grade with and including all fittings such as bends, elbows, tees, short pieces, union etc in trenches complete all as specified and as directed of following sizes :-.

(a) 50 mm dia

(b) 40 mm dia

(c) 25 mm dia

(d) 20 mm dia

Item No 278 : S & F gun metal gate valve with iron wheel head screwed both ends ISI marked fixed to GI pipe including removal old unsv one complete all as specified and as directed of following sizes :-

(a) 50 mm dia

(b) 40 mm dia

(c) 25 mm dia

(d) 20 mm dia

Item No 279 : Supply and fix PVC float valve ISI marked high pressure with PVC float nut complete for iron pipe including removal old unsv one complete all as specified and as directed of following sizes :-

(a) 25 mm dia

(b) 20 mm dia

Item No 280 : M&L for Construction of valve chamber of internal size 600mm x 600mm x 600 mm suitable for 80mm dia sluice valve including necessary earth work excavation PCC 1:4:8 in foundation type D2 using 40mm graded stone aggregate, brick wall in CM 1:4, PCC 1:2:4 type B1 for coping, 15mm thick rendering in CM 1:4 including provision of MS sheet cover 3.0mm thick with MS angle frame 25 x 25 x 3mm all round and at diagonals of size 40 x 40 x 6mm and also MS plate welded to MS angle as shown in drawing, embedded in concrete with suitable hinges and locking arrangements, including two coats of synthetic enamel paint over a coat of red oxide primer necessary excavation earth work etc, all as specified and as directed.

SCHEDULE "A" (Schedule of credit) Schedule of Credit Rs 17,69,981.60 (Minus) inserted by the MES (Note : Credit amount shall be deducted manually to arrive net bid amount)

Mahaveer Engineering Co.

M/S Umashanker Mishra