SPECIAL REPAIRS TO BLDG No T 137 OR LIVING OF DIV CAMP AND SPECIAL REPAIRS TO BLDG No T 63 MAIN OFFICE OF SUP PL ASC AT LIKABALI MIL STN UNDER GE 872 EWS

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (Un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Work or Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Dismantling Timber Scantlings 40 Sq Cm and Over in Section in Unframed Work, Seggregating Serviceable Timber Scantlings and keep in Safe Custody for Refixing, complete all as specified and as directed.

Dismantling Timber Fillets, Rails, Posts, Rafters, Purlins, etc. Under 40 Sq Cm in Section in Unframed Work, complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) of any description, exc. 1.50 Square Metre but not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including Raking out Joints, Hacking for Key, Scrubbing down with Water and removing Debris, etc. etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Hacking/Taking out Broken Glass of any description from Wooden or Metal Frames, or Stone, Concrete or Brick surrounds of any thickness or size; Hacking out Old Putty or Removing Beads, etc., complete all as specified and as directed.

Taking up or down Steel Tubing 15mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Taking up or down Steel Tubing 20mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

M&L Brick Work Half Brick thick with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan to any Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Cutting Holes in Brick Walls, not exc. Half Brick thick, built in Cement Mortar for inserting of Holdfasts, Lugs, etc. and Making Good to dismantled portion with Cement Concrete 1:2:4 (20mm graded stone aggregate) or Cement Mortar 1:3 (as required) and adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) in Scantling, Cleansawn, Timber fixed (Unframed work), fixing with Nails, complete all as specified and as directed.

M&L Refixing only Second Class Hardwood (well seasoned) in Scantlings (Serviceable Timber Scantlings obtained from BOQ Item No. 1.03 here-in-before), Timber fixed (Unframed work), fixing with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain Fillets, Wrought, Square, Rectangular or Triangular in Section, exc. 13.0 Sq Cm but not exc, 25.0 Sq Cm, fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain, Solid, Straight, Chowkats and Frame, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue pinned at Joints, complete all as specified and as directed.

S&F Flush Shutter 35mm thick, Solid Core Construction with Block Board Core and Plywood Face Panels, Commercial type on Both Sides including Teakwood Lipping 6.0mm thick, fixed with Nails, complete all as specified and as directed.

M&L Factory Made Plain Framed, Panelled Shutter 35mm thick (Two Panels) with Lock Rail and Panel of 9.0mm thick BWP. Commercial Ply or 12mm thick Veneered Particle Board with Commercial Veneering on both Faces, having size of Rail and Stile as per IS:1003 (Part I) of Second Class Hardwood (Kiln Seasoned and Chemically Pressure Treated) and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed & Skeleton Shutter 35mm thick, Open rebated and prepared to receive Glass, Gauze, etc. (Without Sash Bars), Edges of Framing plain, chamfered or rounded. fitted with cut and mitred Beads for securing glass, etc.; sizes of Members of Shutters as specified in SSR Part I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 35mm thick, Divided into Squares, with plain, chamfered or rounded, mitred and rebated Sash Bars to receive Gauge/Glass, any numbers, sizes of Members of Shutter as specified in SSR Part-I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 30mm thick, Divided into Squares, with plain, chamfered or rounded, mitred and rebated Sash Bars to receive Gauge/Glass, any numbers, sizes of Members of Shutter as specified in SSR Part-I, Section 8, Clause 8.24(b) and fitted to Chowkat, complete all as specified and as directed.

M&L Taking down Shutter of any description, not exc. 1.0 Square Metre Each and Refixing in the Same Opeing including necessary Resecuring, or Easing & Adjusting, etc., complete all as specified and as directed.

M&L Taking down Shutter of any description, exc. 1.0 Square Metre but not exc. 2.0 Square Metre Each and Refixing in the Same Opeing including necessary Resecuring, or Easing & Adjusting, etc., complete all as specified and as directed

S&F Factory made Solid PVC Door Frame of size 50x47mm made out of 5.0mm thick Plain Colour (Ivory Shade) PVC Sheet reinforced with Mild Steel Square Tube and fixing in opening as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

M&L Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) Plain colour (Ivory shade) consisting of Frame made out of Mild Steel Tubes for Top and Bottom Rails, Mild Steel Frame shall be covered with heat moulded wood grain PVC ‘C’ Channel having a PVC Sheet Strip of 20mm width stuck inside with Solvent Cement for Stiles and wood grain PVC Sheets for Top Rail, Lock Rail & Bottom Rail on either side and as gap insert for Top Rail & Bottom Rail, Panelling of wood grain PVC Sheet to be fitted in the Mild Steel Frame welded/sealed to the Stiles and Rails with suitable 5mm thick x 15mm wide PVC Sheet beading used inside Stiles and Rails and decorative PVC Beading of 10mmx10mm (90) and jointed together with Solvent Cement and fixing in the Frame at Site, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt (as approved), 125mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt (as approved), 150mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt (as approved 300mm long with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge (as approved) 75mm in size, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge (as approved) 100mm in size, complete all as specified and as directed.

S&F Aluminium Handle (as approved) 125mm in size, anodised, Cast type, complete all as specified and as directed.

S&F Aluminium Handle (as approved) 150mm in size, anodised, Cast type, complete all as specified and as directed.

S&F Floor Door Stopper having Overall length of Cover Plate 150mm of Aluminium Alloy Body and Tongue, anodised, with Hard Drawn Steel Spring, fixed in Floor and Fixed-in-repairs, complete all as specified and as directed.

S&F Mild Steel 300mm, Ordinary Rat Tail Rod Pattern Springs including Roller and Roller Plate and Fixed-in-repairs, complete all as specified and as directed.

S&F Hat and Coat Hooks, Brass Solid Body, 175mm to 250mm and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Drapery Rods (Curtain/Harrison Rails) having 24mm Outer dia and 1.0mm thick (minimum), fixing with and including Brackets, Stops, Rollers, Side Holders, etc. and Fixed-in-repairs, complete all as specified and as directed.

M&L Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

M&L Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples and Fixed-in-repairs, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes including Bolts, Hooks (Stay) for large Gates; Hook and Pintle Hinges: large Hasps and Staples; Hand Made Sliding Bolts; Clamps; Holdfasts (Flat Iron 25x3.0mm thick); Wall Ties and similar small Articles conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/ Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Exposed Suspended False Ceiling System having Snap Grid/ Frame Work of size 605x605mm with and including Hangers 4.0mm dia GI (upto 1200mm length) for adjusting Level, fixed to Roof Slabs by means of Ceilling Cleats made out of GI Flat 40x3.0mm in size, 60mm long and Expansion Hold Fasteners 12.5mm dia, 40mm long, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 4.0mm thick, Pre-primed, Self Embossed, Textured Designer Boards, Water Resistant, Termite Resistant, Fire Resistant for insulation, fixed or laid/ inserted to Snap Grid Frame Work with Screws, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 25mm thick in Sub-base for laying of Tiles, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Non-skid Ceramic Coloured/ Designer Tiles 7.0mm to 8.0mm thick, Joint Free (Rectangular/ Square), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm (1st quality as approved) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE: Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-skid Ceramic Coloured/ Designer Tiles 7.0mm to 8.0mm thick, Joint Free (Rectangular/ Square), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm (1st quality as approved) in Vertical Surfaces i.e. Dado, Skirting, etc., set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE: Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Machine cut Granite Tiles 20mm thick, bedded and jointed with Grey Cement Slurry and pointed with White Cement with Admixture of Pigment to match the Shade of Granite Stone including Grinding and Polishing complete fixing over and including Cement Screed Bed 15mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE: Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) 75mm thick in Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without Using Extra Cement, complete all as specified and as directed.

M&L Rendering (Internal) 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (External) 15mm thick on Brick/PCC Blocks or Concrete Works consisting in 2 layers, Backing/Under layer of 10mm thick in Cement Mortar 1:4 and Float/ Top layer 5.0mm thick in Cement Mortar 1:4 including mixeing WPC to Float/ Top layer, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid saperately under appropriate Item,

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and Applying Two Coats of Distemper Oil Emulsion (of approved Tint) over a Coat of Chalk Whitening (Priming Coat), complete all as specified and as directed.

M&L Preparing Old Treated Surfaces on Walls and applying a Coat of Distemper Oil Emulsion (of approved Tint), complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (as approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Old Treated Surfaces on Walls and applying a Coat of Cement Based Paint (as approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Treated Steel and Iron Surfaces of any descriptions, over exc. 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade), complete all as specified and as directed.

M&L Preparing New or Previously Treated Surface of Wood and Wood based Materials of any description and girth and treated with Two Coats of Creosote Oil, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of Wood and Wood Based Materials, of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Backs of Chowkats, etc. Area tarred exc. 0.10 Sqm but not exc. 0.50 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Holdfast or similar Small Items, Area tarred not exc. 0.10 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

S&F Galvanised Steel Tube 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

M&L Refixing Steel Tube 15mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from BOQ Item No. 1.12 here-in-before) in New or Old Position (Walls, Floors, etc.) including Cleaning both Inner and Outer surfaces of Pipes by using Wire Brush including provision of New GI Fittings/ Connections (as required at Sites), complete all as specified and as directed.

S&F Galvanised Steel Tube 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

M&L Refixing Steel Tube 20mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from BOQ Item No. 1.13 here-in-before) in New or Old Position (Walls, Floors, etc.) including Cleaning both Inner and Outer surfaces of Pipes by using Wire Brush including provision of New GI Fittings/ Connections (as required at Sites), complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and Fixed-in-repairs, complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, Swan Neck with Capstan Heads, screwed down, high pressure, with or without Lettered 'Hot' or 'Cold' with long screwed Shanks and Fly-nuts, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Stop Valve 20mm bore (dia), Cast Copper alloy, Chromium Plated, screwed down, high pressure, with Crutch or Butter-fly Handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

S&F Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with PVC (SWR) ‘P’ or ‘S’ Trap and Fixing Bolts and Making Good to Floor/ Distrubed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

S&F White Plastic Water Closet Seat and Cover for Water Closet Pan (Pedestal Pattern), Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminised Hinging Device and Fixed-in-repairs, complete all as specified and as directed.

S&F Jet System (as approved), Chromium Plated suitable for Wash Down Water Closet Pan (Pedestal Pattern) and Fixed-in-repairs, complete all as specified and as directed.

M&L PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float and Handle, a Pair of Cast Iron Brackets Erecting Stand duly Painted, including Polyethylene Pipe (High or Low density) or PVC Flush Pipe 32mm bore (dia) of suitable Length, Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

M&L Vitreous China White Wash Hand Basin of size 550x420mm, Oval shape including Brass Chromium plated Waste Fitting 32mm bore (dia), Polyethylene Pipe (High or Low density) or PVC Waste Pipe 32/40mm bore (dia) of suitable Length, a Pair of Cast Iron Brackets or Erecting Stand duly Painted, Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

S&F Low Density Polyethylene Pipe (LDPE) 32mm bore (dia) of Pressure rating 6.0 Kg/Sq Cm and fixing to Walls, Ceiling or in Floors, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in size and 450mm in length with PTMT Nuts and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Soap Dish, not less than 150mm in size (as approved), fixing to Walls with and including Chromium plated Brass Screws and Wooden/ Plastic Cleats and Fixed-in-repairs, complete all as specified and as directed.

S&F Grating Doom 100mm dia, Chromium Plated with Waste Holes (as approved) and Fixed-in-repairs, complete all as specified and as directed.

M&L PVC (SWR) Floor Trap having 110mm bore (dia) Outlet, Plain with Grating including Jointing/ Connecting to Waste Pipe with Solvent Cement and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, fixed to Walls or laid in Floors including Taking up or down unserviceable Pipe of any description, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, fixed to Walls or laid in Floors including Taking up or down unserviceable Pipe of any description, complete all as specified and as directed.

S&F PVC (SWR) Bend 75mm bore (dia), any radius with Access Door, etc. Jointing with Solvent Cement and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) Bend 110mm bore (dia), any radius with Access Door, etc. Jointing with Solvent Cement and Fixed-in-repairs, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down carefully Copper/Aluminium Point Wiring (Light, Fan, Socket or Power) complete from in any Position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets but excluding Light Fittings of any description, Making Good Disturbed Surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/ Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down unserviceable Sub-main Wiring from Batten/ Conduit/ PVC Casing Capping of any description, Making Good disturbed surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/ Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN POINT controlled by ONE 1-WAY SWITCH 6 AMP, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire for ONE 3/5 PIN SOCKET 6 AMP POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Sub-main Wiring with 2-Run of 4.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable and 1-Run of 2.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuty Conductor drawn through and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc., complete all as specified and as directed. NOTE :- (a) Cost of 3-Run of Cable & 1-Run of PVC Casing Capping shall deem to be include in the Quoted Unit Rate and the same will be Mesured as ONE UNIT. (b) Sub-main Wiring will be measured PVC Conduit only. Wires required for looping, etc. as ordered will deem to be include in the Quoted Unit Rate.

S&F PVC Board of size 100x100x50mm deep with Plastic Laminated Sheet 3.0mm thick with all necessary Fixing Arrangements including Taking down/ out unserviceable PVC Board, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6/16 Amp, 3 Pin, 2-in-1, Multi Plug, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Lamp Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Ceiling Fan Regulator, Dimmer Switch type, 230 Volt AC, Rotary Stepped Electronic, 120/280 Volt including necessary Connection and connecting up, complete all as specified and as directed.

S&F LED Adore 10 Watt, B22 Ball Lamp Decorative Wall Light Fixture made of Polycarbonate, 6500K, suitable for 10 Watt LED Bulb including Taking down Unserviceable Lamp of any description, complete all as specified and as directed. MAKE : HAVELLS, Cat No. : LHLDEUEEML8R010 or equivalent Model in Make : BAJAJ/ CG/ C&S/ PHILIPS (as approved by GE).

S&F Decorative Ultra Slim Square Profile LED Lighting Fixture 1x18 Watt with Light Source LED 18 Watt, 6500K, Extruded Polycarbonate, Enviromental Friendly, Energy Efficient ready and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable including Taking down unser-viceable Light fitting of any description, complete all as specified and as directed. MAKE : HAVELLS, Cat No. : LHEXB1P7IN1W018 or equivalent Model in Make : BAJAJ/ CG/ C&S/ PHILIPS (as approved by GE).

M&L Taking down Ceiling Fan of any Make/Model/Sweep from any Height after disconnecting Electric Connection and Keep in Safe Custody for Re-hanging/ Re-fixing and Repairing, complete all as specified and as directed.

M&L Hanging only Ceiling Fan (Ceiling Fan obtained from BOQ Item No. 2.18 here-in-before) and connecting with and including suitable size Copper Conductor Cable from Ceiling Rose to Ceiling Fan, complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and Connecting up including Taking down/out unserviceable MCB, complete all as specified and as directed.

S&F Isolator Tripole Pole & Neutral 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable Isolator, complete all as specified and as directed.

S&F MCB Distribution Board Sheet Metal Enclosure 8-way, TPN, 240 Volt, Single Door, Front Openable, fixed Flush with Wall inside the Nitches or Outside on Wall Surface suitable for mounting Isolators & MCBs, suitable for Bus-bar 200 Amp rated capacity and connecting up including Taking down/ out Unserviceable MCB DB Sheet Metal Enclosure of any description, complete all as specified and as directed. MAKE : HAVELLS, Cat No. DHDPSHOSRW08 or equivalent in Make : LEGRAND/ L&T/ SCHNEIDER (as approved by GE)

Supply & Laying or Passing through Pipe 1100 Volt grade, Heavy duty, Cross-sectional area 10 Sqmm, 2 Single Core Cable with PVC insulated Aluminium Stranded Conductor served with an inner sheathing of PVC Tape armoured with Galvanised Steel Wire or Tape and Overall PVC sheathed in Service Connection suspended by insulating Hangers not more than 1.0 Metre apart including 4.0mm Suspension Wire including Taking down/ out Unserviceable Service Connection, complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) Light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing including Taking down/out unserviceable Earthing of any description, complete all as specified and as directed.

M/S. NOBIN RAJKHOWA

M/S Raju prasad