SPECIAL REPAIRS TO BLDG NO P-64/01 TO 06 (OR MD ACCN) AT NAR BAHADUR ENCLAVE OF MH, PROVN OF SEPTIC TANK AND SOAKAGE WELL AT MDC AND CERTAIN MINOR WORK IN THE AREA OF AGE B/R-III (W) UNDER GE (W) JABALPUR

Amount

Taking down Cement Plaster any description on brick or stone walls or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Demolition of Brick / Stone Masonry built in Cement Mortar including all quoins arches pillars etc complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including cement mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris of the premises complete all as specified and as directed.

Demolition of Unreinforced Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] complete all as specified and as directed.

Demolition of reinforced Cement Concrete of any description and in nay position complete all as specified and as directed.

Taking down chowkat or frame with shutter (without taking off shutters from the frame) area not exceeding 1.5 Sqm each complete all as specified & directed.

Taking down chowkhat or frame with shutter (without taking off shutters from the frame) area exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified & directed.

Taking down or up steel tubing and connections for 15 mm bore of pipe complete all as specified and as directed.

Taking down or up steel tubing and connections for 20 mm bore of pipe complete all as specified and as directed.

Taking down or up steel tubing and connections for 25 mm or 32mmbore of pipe complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes,bends, swan necks etc. complete all as specified and as directed. Note : Measurement shall be of overall as fixed along the centre line over fittings and accessories.

Dismantling water tanks exc 250 and n exc 500 ltr capacity complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in Soft / Loose soil complete all as specified and as directed.

Excavation over areas not exceeding 1.50 m in depth and getting out in Soft / Loose soil complete all as specified and as directed.

Excavating over areas, exc 1.5 m deep and n exc 3 m getting out in any type of soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in Soft / Loose soil, complete all as specified and as directed.

Excavation in trenches, n exc 1.5m wide and exc 1.5m but n.exc 3.0m in depth for fdn etc or for shafts wells, manholes pier holes etc n.exc 10 Sqm on plan and in soft and loose of soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.

Removal of excavated material [Soil] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

M & L for moorum/ red bajri filling under floors laid in layers not exceeding 15 cm thick, spread levelled and rammed / rolled including watering to required level and gradient complete all as specified and as directed.

M & L for hardcore of gauge not exceeding 63 mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface in broken boulder complete all as specified and as directed.

M & L 50 mm thick sand filling under floors or in foundations including ramming, watering and consolidation complete all as specified and as directed.

M & L of broken bricks Loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage wells complete all as specified and as directed.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate for foundation.complete all as speified and as directed.

M&L PCC 1:3:6 type C1 using 20mm graded stone aggregate as in filling of pressed steel door frame complete all as specified and directed.

M & L for PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) in lintels upto 1.5 clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers ,apex stones, bed plates, water troughs and the like including use of formwork (straight or curved) ,including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed. (Note :-reinforcement where provided shall be measured and paid seprately)

M&L for RCC ( Nominal mix) Type B1 1:2:4 using 20mm grades stone aggregate as in foundation including raft footings, foundation beams, plinth beams, bases of columns and the like complete all as specified and as directed.

M & L for RCC (1:2:4) nominal Mix using 20mm graded aggregate in slab supported on walls,beam and column in floors, roof,landing, balconies,canopies,deck slabs and in shelves and the like complete all as specified and as directed.

M & L for RCC (1:2:4) nominal Mix using 20mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M & L for RCC (1:2:4) nominal Mix using 20mm graded aggregate in chajjas,parapet facia etc complete all as specified and as directed.

M & L for RCC (Nominal mix) Type B1 1:2:4 using 20mm graded stone aggregate as in coloumn,pillars,piers, posts and struts complete all as specified and as directed.

M&L for RCC -M-25 ( nominal mix) using 20mm grades stone aggregate as in Fins, fascias, louvres,parapets, and railings exc.60cm in height, newels, balustrade, and the like complete all as specified and as directed.

M&L for pre cast RCC 1:2:4 type B1 using 20mm graded stone aggregate as in cover slab set in CM 1:4 complete all as specified and as directed..

Supply only liquid integral water proofing compound

Supply only integral water proofing compound

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed.

Extra for forming fair finished drains or channels 30 cm inner girth in cement concrete using extra cement including forms moulds, mitered/ stopped ends complete all as specified.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 all as specified and as directed.

M&L for Cutting holes in brick walls exc half brick and nexc one brick in cement in mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 complete all as specified and as directed.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:6) complete all as specified and directed.

M&L for Brickwork with fly ash bricks or brick tiles in brick on edge walls (less than1/2 brick thick), built in cement mortar (1:4) complete all as specified and directed.

S & F Brickwork with sub class ‘B’ bricks in one brick thick honey comb walling, built in cement mortar 1:6 complete all as specified and directed.

M & L for brick work with sub class "B" bricks, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

Brickwork with subclass ‘B’ bricks, old size straight or curved on plan to any radius in half brick thick walls built in in CM 1:4 complete all as specified and as directed.

Form work to edges of concrete flats, treads breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roof and sides of bands in walls, horizontal or sloping and similar work for rough finished concrete surface exc 10 cm but not exc 20 cm wide complete all as specified and directed.

Use and waste of form work to sides of concrete foundation, footings, bases of column, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter; for rough finished surfaces complete all as specified and as directed.

Use and waste of form work to Chajjas and similar items including edges etc complete all as specified and as directed.

Use and waste of form work to faces of walls, retaining walls , abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc, vertical or to batter surface fair finished complete all as specified and directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including fair finished surfaces complete all as specified and directed.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders,bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floor and beam etc. for rough finished surfaces complete all as specified and as directed.

Use and waste of form work to sides of pillars, posts, struts, piers, columns of any shape / cross section for fair finished surfaces of concrete complete all as specified and as directed.

S&F in repair 18/19 mm thick water proof block board of exterior grade Gde-I fixed with screws as kitchen, cup board box and shutters & shelves etc complete all as specified and as directed.

S&F in repair 18 mm thick PVC sheet one side prelaminated of approved texture ("celuca ply of Rajshree make or equivalent in "Sintex" as approved by GE) as in Kitchen cabinet. (with shelves and partitions) including necessary fitting & fixture as per manucture's instructions complete all as specified and as directed.

S&F PVC door frame size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinf with MS square tube supplying & fixing in opening as per specificationn make Rajshree.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails . M,S frame shall be covered with heat moulded plain colour PVC ,C, channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails , lock rails and bottom rails on either side and as gap insert for top rail and bottom rail Panelling of plain colour PVC sheet to be fitted in the M.S frame welded /sealed to the stiles & rails with suitable PVC sheet beading , and jointed together with solvent cement , supplying and fising in the frame at site as per specification and drawing. Make Rajshree

S & F factory made 35 mm thick plain, framed, panelled shutters (Two panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces and size of the members of shutter are as per IS – 1003 (Part – I) made of kiln seasoned & chemically pressure treated 2nd class hardwood rail and style complete all as specified and directed.

S & F 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part -I,section 8,clause 8.24 (a) complete all as specified and as directed.fitted to chowkhats for doors etc complete all as specified and as directed.

S&F aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm complete all as specified and as directed.

S&F aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm complete all as specified and as directed

S & F Aluminium alloy, anodised, Sliding Door Bolt with hasp and staple [Bolt Type] of size 300 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S&F 100mm butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, Type B-21 complete all as specified and directed.

S&F continuos (piano) hinges, mild steel bright finish or electrogalvanised, width of flaps 30 mm complete all as specified and as directed.

S&F extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and as directed.

S&F extruded aluminium alloy handles, fabricated type, anodised of size 125 mm complete all as specified and directed.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel spring complete all as specified and directed.

S&F 300 mm long mild steel ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed.

S&F 125mm hasp and staples, aluminium anodized including bolt to hinges plate and fixed with screws complete all as specified and directed

S&F stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified.

S&F Handles of senso (as per 3D designs) 150mm including all connection fitting complete all as specified and as directed.

S&F in repair stainless steel hinges of 75mm for cupboards of senso (as per 3D designs) including all connection fitting as complete all as specified and directed and approved by GE.

S&F Europa cupboard locks as complete all as specified and directed.

S&F aluminium hat & coat hooks solid body 125 mm to 175 mm fixed with brass screw complete all as specified and directed.

S&F MS Peg set of six powder coated as approved complete all specified and as directed

M&L for mild steel pipe 25 mm dia Drapery rod fancy type with PVC coating fixed in the MS hooks, and finials/ side brackets (both side), shade as approved by GE all as specified.

S&F Aluminium anodised sections for doors/windows/ventilators with one or more rebates including joining cleat including locking arrangment for fixing etc complete with frames, shutters and grills of size complete all as specified and directed. Note:- sheet glass, wire cloth shall be measured and paid seperately.

S & F pressed steel door frame 105x60 mm with one or more rebates including necessary fixing lugs hings, lock strick plates, etc complete all as specified and as directed.

M&L Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed ® size 125x 60 mm complete all specified and directed

S&F steel windows or ventilators, fixed type with glazing bars complete all as specified and as directed..

S&F mild steel framed work such as guard bars/grills, grating etc with end of bars shouldered and/or riveted or forged into spikes and similar works including one shop coat of zinc chromate primer complete all as specified and as directed.

M&L reinforcement using TMT steel bars of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F reinforcement using TMT steel bars of 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping,stirrups,hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F reinforcement using TMT steel bars of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F MS works for fencing post and struts including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets, MS Rungs (for securing wire mesh etc) including all necessary drilling, bolting or riveting, etc conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L Expanded metal nexc 4 Kg/sqm cut to length, bent to shape required and typing with and including annealed mild steel wire not less than 0.9 mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete all as specified and as directed.

Roughening surfaces of old concrete floor/terrace by picking incl. taking down existing detoriated/ decayed tar felt, PCC tiles or any type of treatment including loose surface, scraping with scraper, chiseling, scraping of surface with wire brush or any other method, sweeping, clean & washing down with water to remove dust etc. and removing the scraped materials debris to a distance not exc. 50 m complete all as specified and as directed.

M&L for wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashing and junction of parapets, etc., and surfaces painting with a layer of blown bitumen of any penetration applied hot @1.70 kg per sqm. blended with grit or pea size gravel @ 0.006 cu.m per sqm and lightly tampered area of flashing etc. shall be added to the roof area complete all as specified and as directed.

Bitumastic gola, with 80/25 bitumen and coarse sand mixture, 1:3 by weight, 8cmx8cm at the junction of roofing to vertical surfaces complete all as specified and as directed.

M&L for 10 mm thick screed bed or bedding layer in CM 1:3 mixed with water proofing compound as per manufacturers instructions on concrete roof surfaces finished fair and even to maintain the proper slope of roof surface etc complete all as specified and as directed.

M&L for Providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing memberane comprising of the following for roofs-

(a) Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.30 kg/Sqm on top of dry surface of finished cement mortar plaster.

(b) One coat of hot blown bitumen of grade 85/25 @ 1.2kg /sqm shall be applied over primed surfaces.

(c) One layer of APP based polymeric water proofing membrane of weight not less than 3 kg/Sqm consisting 3mm thick reinforced with polyster non wove fabric shall be unrolled surfaces with lap of 100 mm and the over lap shall be sealed by flame.

(d) Applying two coats of aluminum paint on top of membrane @ 0.10Kg/Sqm complete all as specified and as directed..

M&L for 20mm thick Screed bed or bedding layer of cement mortar 1:4 complete all specified and directed.

M&L for glazed ceramic coloured tiles of size 450 x 300 x 6 to 7 mm, 450x350 or 350x250 6 to 7mm thick on vertical surfaces such as skirting/ dado etc. ,set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile with & including rendering 10 mm thick cement plaster in cement mortar 1:4 finished rough to receive tiles complete all as specified and as directed.

M&L for pave smart heavy duty parking tiles 40 cm x 40 cm x 11 mm thick set, jointed and pointed in neat cement slurry as in floors, walls etc incl 15 mm thick cement screed bed/plaster in 1:4 CM and incl necessary epoxy adhesive material to be used for fixing of tiles complete all as specified and as directed

S&F cement concrete tiles size 25cmx25cmx22mm thick machine cut pressed set jointed and pointed in neat cement slurry with grey cement and pigments in floors and cut and polished complete all as specified and directed.

M&L Non skid coloured ceramic tiles 7 to 8mm thick square/ rectangular area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floor etc set and jointed in neat cement slurry and pointed in white cement with pigment to match, laid over and including 15mm thick cement screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or rectangular) area of Each tile exc 0.18 Sqm but not exceeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed..

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or rectangular) area of Each tile exc 0.18 Sqm but not exceeding 0.36 Sqm, as in skirting ,dados in vertical surfaces etc and including 10mm thick cement plaster 1:4 complete all as specified and directed.

M&L for Granite (of any type) 20 mm thick work (table rubbed and polished ) as in steps, jambs, pilllars, window cill, cooking plateforms and like laid over 20mm thick screed bed in CM 1:6, including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of Granite complete all as specified and as directed.

M & L for 20-25mm thick Machine cut Cudappha stone slab as in cooking platform/ shelf laid over and including 20mm cement screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for rounding edges of granite stone slabs one edge such as in counter type WHB platform etc. complete all as specified and as directed.

M & L for 20 to 25 mm thick machine cut kota stone flooring laid over cement screed bed 20 mm thick bedding layer in cement mortar 1:6 and jointed with neat cement slurry mixed with pigment to match the shade of the slab and including rubbing and polishing complete all as specified and as directed.

M&L for 18 to 20 mm thick machine cut kota stone as in vertical surfaces, risers of steps, skirting, dado and pillars etc laid over and including 10 mm thick rendering in cement mortar 1:4, set and jointed in neat cement slurry and pointed with grey cement mixed with pigment to match the colour of stone slab and including rubbing and mirror polishing complete all as specified and as directed.

M&L 75 mm thick PCC 1:3:6 type C-1 using 20mm graded aggregate as in plinth protection finishing even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand ( all by weight) complete all as specified and as directed.

M&L 50 mm thick PCC 1:3:6 type C-2 using 20mm graded aggregate as in plinth protection finishing even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand ( all by weight) complete.

M&L 100mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed

M & L for 25 mm thick, PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in Sub base for flooring complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment, confirming to IS 15658-2006of 60mm thickness M 35 Grade complete all as specified and as directed.

M&L 5mm thick rendering in Cement Mortar 1:3 on Concrete Surfaces, ceiling etc finished surface Even and Smooth, without using extra cement

M&L for 10mm thick rendering in cement mortar 1:6 on fair faces brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L 15mm thick rendering on fair faces of concrete/brick surfaces in CM 1:4 mixed with water proofing compound as per manufactures instruction finished even and smooth without using extra cement complete all as specified and as directed. Note:- WPC shall be measured and paid sperately.

M&L for 15mm thick plaster in CM 1:3 in two layers,with & including wire netting of galvanized steel wire 0.91mm dia and mesh size 12mm placed in walls before plaster layers and fixed with tinned tack or wire stapled where required first layer of 10mm thick plaster in cement mortar 1:4 & second layer of 5mm thick in cement mortar 1:3 including taking down of loose /bulsing surafces of plastered or concrete as in chajjas, beam balcony fins etc to make to original shape at any height to repair chajjas, beam balcony fins etc in multistoreyed buildings, top layer of plaster finished even & smooth without using extra cement complete including cleaning and preparation of existing RCC surfaces and applying a coat of cement slurry and surface shall be match & finish the existing surface by applying two or more coats of cement base paint/ anti fungal exterior emulsion paint complete all as specified and directed. Note : Each layer of plaster shall

M & L for preparing newly plastered wall surfaces and applying three coats of white wash complete all as specified and as directed.

M&L for Preparing Newly Plastered Surfaces of internal wall and applying two Coats of oil emulsion distemper over a coat of primer over and including 3 mm thick wall care putty on plastered wall surfaces complete all as specified and as directed.

M&L for Preparing Newly Plastered Surfaces of external Walls and applying two coats of Cement Base Paint over a coat of alkali resistance primer complete all as as specified and as directed.

M & L for complete removal of existing wall surface finishes of any description and applying two coats of cement based paint over a coat of alkali resistant primer on walls complete all as specified and as directed.

M & L for complete removal of existing wall surface finishes of any description and applying two coats of oil bound distemper over one coat of primer over and including 2mm thick wall care putty and preparation of surfaces complete all as specified and as directed.

M&L for Prepration of old surfaces of ceiling includinng scrapping down smoke ,soot,and efflorescent salts and treatings oil and gresy spots, brooming down or steel wire brushing removing nails making good holes cracks etc on plastered or unplastered surfaces and applying one coat of white wash on ceiling surface complete all as specified

S&F 4mm thick figured glass, pin headed type and glazing with oil putty in square n. exc 0.5 sqm in each pane complete all as specified and as directed.

S&F 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and as directed.

M&L for Preparation of newly wooden surface of any description over 10 cm width or grith and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for Prepration of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint of white or tinted complete all as specified and as specified.

M&L for Prepration of old painted surfaces of steel of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for treating small article such as stops, covers, gully, gratings and hold fast ends & post backs of chowkat etc with creosote oil, tarred area n exc 0.10 Sqm each complete all as specified and as directed.

M&L for Preparation of new steel surfaces of any description over 10 cm width or grith and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

S&F in repair PVC Bath Cabinet made from hard thermosetting material with mirror, white/ivory colour, 400 x 500mm size. Complete all as specified and as directed. Make- Prayag Cat Part No 554 or equivalent make as mentioned here-in-after.

S & F GI water tubing of 25 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

S & F GI water tubing of 20 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

S & F GI water tubing of 15 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

S& F Stop valve / Angle valve fancy type cast copper alloy chromium plated screwed down high pressure with capstan heads screwed both ends for iron pipe or for union and fixed 15mm bore complete all as specified and directed.

S&F in repairs fancy type wall mixture of brass, chromium plated, 3 in 1 system with hot and cold arrangement, with provision for both hand shower & overhead shower complete all as specified and as directed.

S&F in repair CP glass corner shelf set of three and including fixed CP Screws and CP brackets complete all as specified and as directed.

S&F in repair Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall Size 915mmx460mm with bowl size 410mm x330mm x 160mm complete all as specified and as directed.

S&F in repairs kitchen plate rack made of stainless steel 1mm thick complete size 1200 x 900mm x 200mm width of trade pattern complete all as specified and as directed.

S& F in repairs 15 mm bore bib tap cast copper alloy, chromium plated, long body fancy type with capstan headed, screwed down, screwed for iron pipe complete all as specified and directed.

S&F 15mm dia pillar tap cast copper alloy chromium plated capstan head screwed down high pressure with or without lettered hot or cold with long screw shank and fly nutt screw for iron pipe complete all as specified and directed.

S&F in repair for 15mm chromium plated brass CP mixer for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed.

S& F in repairs Vitreous China wash hand basin, white, flat back, size 550mm x 400mm including brass coupling, mild steel brackets fixed to wall, with pedestal complete all as specified and as directed.

S&F CP waste fittings brass chromium plated for sink 32mm dia with long screws, shanks and fly nuts , flanged end, bedded in red led cement and other in fixed all as specified and as directed.

S&F CP waste fittings brass chromium plated for sink 40mm dia with long screws, shanks and fly nuts , flanged end, bedded in red led cement and other in fixed all as specified and as directed.

S&F in repair vitreous China squatting pan of pattern Orissa Pan, size 580 x 440 mm white with integral foot rests any pattertn (excl flushing cistern and flush pipe) complete and including provision of lime concrete bedding, connection to flush pipe, trap etc and making good complete all as specified and as directed.

S&F vitreous china wash down water closet pan Padestal pattern white excluding fixing bolts, flushing cistern and flush pipe with and incl 'P' or 'S' trap and making good to floor to match with existing all as specified and directed.

S&F in repair Plastic water closet seat, white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device complete all as specified and as directed.. Make- as approved by GE.

S&F PVC 10 litres capacity valveless ,syphonic action type low level flushing cistern ,white including flush pipe, cantilever brackets ,inlet, ball valve, float and handle, PVC connection 32mm dia, 450mm long etc complete all as specified and directed (Make: PRAYAG / CERA/ Parryware/Jaquar).

S&F for Soap dish, stainless steel of size 160mm x 160mm x 90mm complete all as specified and as directed.

M&L for 32 mm bore low density polythelene pipes (LDPE) with fittings of pressure rating 6 Kgf / Sqcm fixed to walls or in floors etc complete all as specified and as directed.

S&F in repair PVC connection pipe of 450 mm long, 15mm size with PTMT nuts complete all as specified and as directed.

S&F in repairs grating of doom 100mm dia PTMT with waste hole (Min weight 25 grms) complete all as specified and as directed.

S& F in repairs chromium plated shower rose 125 mm size and 15mm dia with or without swivel joints including fixed to pipe or union complete all as specified and as directed

S & F in repairs Towel rail 600 mm long and 20 mm dia brass chromium plated 'D' type fixed with screws and wooden or plastic cleats complete all as specified and as directed.

S & F in repairs Towel ring brass chromium plated round type fixed with screws and wooden or plastic cleats complete all as specified and directed.

S& F 500 ltrs rotational moulded polythine water storage tanks (cylinder vertical with closed top) hoisted and fixed in position including ball brass valves, high pressure with polythene float and flynut complete screw for iron pipe or brass ferrule all as specified in SSR Part-I complete all as specified and as directed.

S & F 20mm bore ball valve high pressure PTMT with epoxy coated aluminium rod & high densitypolythene float ball and fly nut screwed for iron pipe complete all as specified.

S&F 20mm dia gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all specified and directed

S&F 25mm dia gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all specified and directed

M&L for 100mm dia cast iron floor trap plain with grating including jointing and fixed with cement concrete type B-0 (1:2:4) complete all as specified and as directed.

M&L for 75mm dia PTMT multi floor trap plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F 110 mm dia PVC (SWR ) pipes Single socketed in any length with rubber ring jonits fixed to walls complete all as specified and as directed.

S&F 75 mm dia PVC (SWR ) pipes Single socketed in any length with rubber ring jonits fixed to walls complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) bends any radius with access door complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) bends any radius with access door complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) vent cowl including jointing with solvent cement complete all as specified and directed.

M/L PVC (SWR) Tee of 110mm dia with access door etc complete all as specified and directed

M/L PVC (SWR) Tee of 75mm dia with access door etc complete all as specified and directed

S&F 110 mm dia PVC (SWR ) branches piece,double (double Y) equal or unequal with access doorrubber rings ljoits fixed to walls complete all as specified and as directed.

S&F PVC (SWR) branch pieces, single (equal or un equal) , ordinary or inverted (spigot or socket type) or with parralled branches of 110 mm dia with access door

S&F PVC (SWR) gully trap 125 x 110 mm setting and jointing with solvent cement complete all as specified

S & F stack clamps out of 50mm by 5mm flat iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore etc all as specified.

M&L for double wall corrugated (DWC) pipes 200 mm bore inner dia class class SN-8 confirming to IS-16098:2013 (Part-2) laid and jointed, with collars complete all as specified and directed

M&L for double wall corrugated (DWC) pipes 150 mm bore inner dia class class SN-8 confirming to IS-16098:2013 (Part-2) laid and jointed, with collars complete all as specified and directed

Concrete bed to drain pipes including packing under and haunching against the sides of pipes after the air laid and tested in Cement Concrete 1:3:6 type C2 for bore of pipes 200mm dia complete all as specified and directed

Concrete bed to drain pipes including packing under and haunching against the sides of pipes after the air laid and tested in Cement Concrete 1:3:6 type C2 for bore of pipes 150mm dia complete all as specified and directed

Cutting into existing manholes or septic tank for connecting new drains, making good to pipe and rendering, curring out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 typeB-1 smooth finished for 100mm dia complete all as directed

Taking down carefully any type point wiring (light, fan, socket bell or power) complete with fittings such as switches, ceiling roses, lamp holders, sockets,regulators, call bell light fitting with PVC conduit surface/concealed or wooden pattens including sunken cast iron/pressed steel terminal boxes etc and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces all as specified and directed by Engineer in Charge.

Taking down carefully Main switch and distribution boards of any make and size complete all as specified and as directed.

Taking down the ceiling fan in situ repairing overhauling painting fans and fixing it after rectifying all defects complete all as specified and as directed.

Taking down carefully Old unserviceable any type sub main wiring with wooden batten/ PVC surface conduit of any size and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified and directed.

S & F in repair for bell ding dong AC 230 volts single pole one way complete all as specified and directed.

M/L for Sub Main Wiring with two single core PVC insulated cable FRLSH of size 4.0 Sqmm multistranded copper conductor FRLSH cable drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 20mm dia with all conduit fitting, fixing accessories and 4 Sqmm multistrand copper conductor FRLSH cable as continuous earth wire complete all as specified and as directed. Note :- Two Nos of 4.0 Sqmm Wire and One No of 4 Sqmm Earth wire in One RM length Measured as one unit length.

M/L for Sub Main Wiring with two single core PVC insulated cable FRLSH of size 6.0 Sqmm multistranded copper conductor FRLSH cable drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 25mm dia with all conduit fitting, fixing accessories and 4 Sqmm multistrand copper conductor FRLSH cable as continuous earth wire complete all as specified and as directed. Note :- Two Nos of 6.0 Sqmm Wire and One No of 4 Sqmm Earth wire in One RM length Measured as one unit length.

M&L for Point wiring with PVC insulated 1.5 sq mm multi stranded copper conductor FRLSH cable 1100 volts grade drawn into and including concealed PVC conduit not less than 20mm (ISI marked) including all fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes duly painted with two coats of anticorrosive paint outside and two coats of aluminium paint inside, 2.8mm thick hylam brand laminated white Bakelite sheet cover for mounting of switches, sockets, fan regulators etc and PVC insulated 1.5 Sqmm multistranded copper conductor FRLSH cable as earth wire and making good the disturbed surfaces to match with the existing surfaces complete all as specified and directed.

(a) One light point/fan point/bell point controlled by one switch.

(b) One socket point controlled by one switch on same board.

(c) One socket point controlled by one switch on Independent board.

All as described in serial item No. 91 here-in-before, but with 1100 volts grade copper standard conductor FRLSH cable of size 2.5 Sqmm with 2.5 Sqmm solid copper conductor cable for 3 pin 15 Amp switch socket outlet independent board complete all as specified and directed.

S & F in repair for switch piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed by Engineer in charge.

S & F Socket outlet 3 pin, 5 Amps and AC 230 volts flush type complete all as specified and directed.

S & F switch socket combination 3 pin 5 and 16 Amps AC 230 volts flush type complete all as specified and as directed.

S & F Ceiling rose surface bakelite 65 mm x 50 mm three terminal AC 230 volts flush type complete all as specified and as directed.

S&F LED lamp rotary type/holder type of 12 watt all as specified and as directed.

S & F in repair lamp holder PVC Polycarbonate type body, with back plate for batten fitting icluding 9 watt led lamp complete all as specified and as directed by Engineer in charge. Make: anchor/plaza/leader

S&F fan regulator Step type of polycarbonate complete all as specified and as directed.

Supply and fixing Single phase ceiling fan 1200 mm permanent magnet brushless DC Motor 230 v 50 Hz single phase 26-30watt rated current 0.16 amp,pf 0.98 370/360 rpm air delivery 220m3 rated service value 629m3/min/watt no of blades three type of blade leaf 1.05 mm thick aluminium sheet remote control radio frequency 5 speed +off timer option speed regulation class of insulation two nos bearings including connecting wire complete with all as required and directed at site by eng in charge Make : Havells/ CG/ Bajaj

Supply & fixing, in replacement, Kit kat DB by SPN Distribution box double door, protection grade IP 43, in fine powder coated matt finish with best CRCA sheet fitted with shrouded neutral insulated pin type copper bus bar Din rail earth bar, 8 way conforming to IS 13032 & 8623 complete all as specified and directed ( Make : Legrand CAT NO 507621 / SIEMENS / Schneider (Electric) as approved by GE)

S & F in repair of LED Decorative /mirror light fitting 9 watt along with fixture Surface mounted suitable for indoor aplication , connector block, etc . Complete with all accessories internally pre-wired and including round wood block, connecting up with three core flexible flexible copper conductor cable suitable size complete all as specified and directed by Engineer in charge. Make- Havells LUMILINEPLUSSBS10WLED865SPCSS or equivalent makes as mentioned here-in-after.

S&F in repairs Smart bright Batten Series, LED luminaire using LED 22 watt 110 Lumens/watt with diffuser which ensures uniform distribution and comfort, batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminium housing, Energy efficient, Flicker free start Inbuilt driver unit, Suitable for wall and ceiling mounting using brackets with and including the luminaire testing on completion as per Standard Specification IEC 60598-2-1 / IS: 10322(Parts/Secl), (Make : Philips Cat part No BN 021 LED 22S 6500/4000 PSU GR S1 or equivalent makes as mentioned here-in-after.

Supply & fix in replacement of LED Security Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed. Make:Havells cat part no: LHDAUU7PA7J025 or equivalent makes as mentioned here-in-after.

Supply & Fixing sheet metal enclosure MCB DB double door [Acrylic], single pole and neutral, 240 volts, 8 way with 200 Amp, 10 KA breaking capacity rated bus bar with blanking plate wherever required and IP-43 degree protection complete all as specified & directed.Make : Legrand CAT NO 507611 / SIEMENS CAT NO 8 GB 32102RC8/GE

Supply & Fixing in repair single pole and netural sheet metal enclosure with a two pin and earth plug and socket complete with 01 number single pole MCB 20 Amps complete all as specified & directed. Make:- Legrand/ havells or Equivalent

S & F for MCB Single pole and neutral rated capacity 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.Make : Legrand DX3 DP CAT No 408637/ Siemens cat no- 5SL 42327RC / GE

S & F in replacement MCB Single pole and neutral rated capacity 240 Volts 40 Amps, B series complete all as specified and directed by Engineer in charge

Supply and fixing in replacement MCB/Isolators single pole 240 volts upto 40 Amps, B Series complete all as specified and directed by Engineer in charge

S & F for MCB Single pole rated capacity 5 to 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.Make : Legrand cat no DX3 SP 408587,408590,408592,408593,408594,408595 / Siemens cat no- 5SL41067RC, 5SL41107RC, 5SL41167RC, 5SL41207RC, 5SL41257RC, 5SL41327RC / GE

S & F in repair Bulk head endura LED light fitting complete with10 watt LED and making necessary electric connection to ceiling rose with copper conductor of suiyable size & length complete all as specified & directed. Make :Havells Cat Part No. HEXAFT10WLED857SSYMBOPC or Equivalent make Philips / BAJAJ / WIPRO

Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

S&F in replacement of sheet steel enclouser distribution boards, double door factory made VTPN 4 way 3 phase 415 volts 4 way with 200 amps rating copper bus bar and PVC insulated copper jumpers of suitable size from the MCCB to the out going circuits one incoming MCCB 63 amps , circuits comprising of 3 phase 4 wire of suitable rating all as specified and directed.Make of Distribution Board Legrand cat no:5077 50 or equivalent in seimens /GE and Make of MCBs :Legrand/Seimens/GE

S & F MCB TPN 25 to 63 Amps, 240 Volts, minimum 10 KA, "C" series rupturing capacity and to be housed in DBs catered here in before complete all as specified and directed :-(Make- Legrand / L&T / Havells)(Note :- Proper and suitable size cablecopper lugs to be fixed with MCBs are included in unit rate of each MCB of any rating)

S & F in repair for bell push piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed by Engineer in charge.

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 300 mm sweep PVC body complete , including making holes of suitable size and making good the disturbed surface and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.Make:Bajaj,havells or equivalent.

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 230 mm sweep PVC body complete , including making holes of suitable size and making good the disturbed surface and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.Make:Bajaj,havells or equivalent.

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 380 mm sweep, metallic body complete with Metalic louvers including making holes of suitable size and making good the disturbed surface and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.Make:Bajaj,havells or equivalent.

S&F decorative wall light fitting WITH LAMPS 9 WATT made up of Polycarbonate, City-1, Cylindrical shape, with LED lamp 9 Watt complete with fixing arrangements on wall all as specified and directed. Make:City 1 of havells or equivalent makes mentioned here-in-after.

Supply, installation, commissioning and testing indoor wall mounting LT Panel Board of minimum size 1.20 m (height) x 1.20 m (breath) x 0.30m (depth) factory made CPRI approved panel, weather, dust & vermin proof indoor, double door, front openable, including four comparment for fixing of Seven nos single phase meter and MCB and providing glass view for reading of meter and providing rubber/ PVC gasket of suitable size all sides of door, with copper busbar wrapped with PVC tape/ sleeves with maintained the colour code and copper strip/wire busbar of suitable size to MCCB input and MCCB/MCB output of suitable length for connection of cable from main busbar, made out of 2.00 mm thick mild steel CRCA sheet with suitable size angle iron supporting frame including applying two coats of Powder coated paint over a coat of red oxide zinc chrome primer over exposed external & internal surfaces suitable for 3 phase 4 wire system 415/440 volts grade including complete internal wiring with 1.5 sqmm copper wire and connections of all outgoing / incomming existing cable of any size complete all as directed by Engineer-in-Charge. (For JCO/ORs, Civilian Md Accn 04 Qtrs)

OUTGOING :- (a) MCB, Single pole & neutral, 40 amps, 240 volts, 'C' curve, 10 KA all complete as specified and as directed -04 Nos (b) MCB, Single pole & neutral, 10 amps, 240 volts, 'C' curve, 10 KA all complete as specified and as directed - 1 No.(stair case lighting) (c) Fixing only serviceable existing electric meter - 01 No. (d) Smart Single Phase Meter AC single phase two wire, tamper proof, static meter of class 1.0, 240Volts, 50 Hz of capacity 10 Amps-60 Amps conforming to IS-16444 and relevant IEC standards with in built 865-867 MHz radio frequency communication facility with self healing mesh netork with default and on demand display, billing data generation facility, antitemper features, microprocessor and LED/LCD based circuitry. Meter should support the follwing data: 30 min instantanous data for voltage, current, power factor, power cumulative energy and frequency, 30 load survey data for energy, monthly billing survey for cumulative energy and max demand. Meter should have connnect/disconnect funtionality operable compactable system from prepaid billing software in future. The meter should support open communication protocol DLMS with the software. 04 Nos. (Make-L&T, Secure, Schneider)

Supply , laying and testsilng cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cables ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 2 core 16 Sqmm complete all as specified and directed.

Supply , laying and testsilng cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cables ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 4 core 25 Sqmm complete all as specified and directed by Engineer in charge

Supply and lay DWCP pipe OD 65 mm , ID 38 mm all as per required and directed by Engg I charge(Necessary excavtion may please be added in rate quoted) complete all as specified and as directed.

RAM PRASAD AHIRWAR

ELITE ENGINEERING COMPANY

DEEPAK CONSTRUCTION