Site and Infrastructure Package Contract-II

Amount

Earth work

Excavation work in all kinds of soil by pick axes or spades or hydraulic excavator in foundations, pits, trenches,reservoirs,drains etc. including de-watering, dressing at sides and ramming at bottom lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil to stack or fill in the adjoining area within a lead of 1000 m.

Same as above item no.1.01, but lift beyond 1.5 m upto 3.0 m

Excavation work in ordinary rock by mechanical means( Hydraulic excavator)/manual means in foundations, trenches, reservoirs, drains etc. including dewatering,dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil to stack or fill in the adjoining area or as directed, within a lead of 1000 m.

Same as above item no.1.03, but lift beyond 1.5 m upto any depth.

Filling the available excavted earth/ laterite (to be broken into pieces of not larger than 150 mm excluding rock) in trenches, plinths, sides of foundations etc. in layers not exceeding 20 cm in depth with proper compaction so as to achieve a standard proctor density of not less than 90% for each deposited layer by ramming and watering.

Extra over item no. 1.01 to 1.04 for disposal of excavated earth & ordinary rock beyond initial lead of 1000 m and upto 2000 m complete in all respect as per specification and instruction of E.I.C.

Supplying and filling in plinths with sand under floors, including watering,ramming,consolidating and dressing complete.

Surface dressing in all kind of soil of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 500 m and lift upto 1.5 m

Stone work

Dry stone pitching 22.5 cm thick along inclines surfaces of embankment and along the slope of water reservoir including providing supply of stones and preparing surface complete as per approved drawing or as per direction of EIC.

Coursed rubble masonry (including plaster)(first sort) with hard stone in foundation, Road divider,peripherial drain,road guard wall other retaining structure and plinth with :Cement mortar 1:6 (1 cement : 6 coarse sand)

HDPE film

Supplying & laying Double Wall Corrugated (with external annular corrugation and smooth internal walls) High Density Polyethelene Pipes conforming to IS 16098 (Part-II):2013 having Stiffness Class of SN 8 with Ring Stiffness not less than 8.00 KN/Sqm. and Impact Resistance TIR value not more than 10% including necessary jointing materials for nonpressure underground Drainage, Sewerage & Cross drainage application.

(i) 150mm internal dia.

Concrete Work (PCC / RCC / PRECAST)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All works upto plinth level :1:4:8 (1: cement:3 coarse sand: 8 graded stone aggregate 20 mm nominal size)

Same as above item-4.01, 1:3:6 (1: cement:3 coarse sand: 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position machine batched and machine mixed design mix M 25 grade cement concrete for RCC works, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixures in recommended proportions as per IS: 9103 to acelerate,retard,setting of concrete, improve workability without impairing strength and durability as per directions Engineer-in- charge. Concrete of M25 grade with minimum cement content of 330 kg /cum : All works upto plinth level

All works as per 4.03 for above plinth level.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; All works upto plinth level for the following grades of concrete. Concrete of M40 grade with minimum cement content of 390 kg/cum

All works as per 4.05 for above plinth level.

Steel reinforcement for RCC work including straightening, bending, placing in position and binding all complete : Cold twisted bars conforming IS:1786

Supplying, installing, dismantling and removing following classes / class of formworks for foundation & sub-structures in all kinds of work including necessary rendering of concrete surfaces after exposure as per drawings, specification and direction of Engineer : Steel / Plywood

Supplying, installing, dismantling and removing following classes / class of formworks for super-structures including necessary rendering of concrete surfaces after exposure as per drawings, specification and direction of Engineer : Steel / plywood

Providing and laying in position specified grade of reinforced cement concrete slab on grade excluding the costs of centering, shuttering, finishing and reinforcement- All work upto plinth level : 1:1.5:3 (1: cement:1.5 coarse sand: 3 graded stone aggregate 20mm nominal size)

Providing and laying damp proof course 50 mm thick with cement concrete M20 with approved waterproofing admixture below the concrete block masonry work at Plinth level.

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in lintels, beams,Cover slab and bressumers including setting in cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering and shuttering but excluding the cost of reinforcement with, 1:1.5:3 (1 cement : 1.5 coarse sand incuding manufactured sand derived from Recycled Concrete Aggregate (RCA) upto 20% : 3 graded stone aggregate 20 mm nominal size Recycled Concrete Aggregate (RCA) upto 20%).

Structural steel work

Supply, Fabrication and Erection of structural Steel works in single or builtup sections like joists,channels,pipes etc. as per drawing including tools, tackles, cutting, welding, consumables, assembly, bolts, permanent bolts, preparation of Fabrication drawings for all types of structures in buildings, pipe racks, platforms, towers or any other structure as specified in Technical specification and drawing and applying one prime coat, and with not less than two field coats. The thickness of the prime coat shall not be less than 75 microns and the total thickness of the two field coats shall not be less than 125 microns, complete in all respect.

Supplying, fabricating, handling and laying in position of insert plates, angles etc. complete with all lugs including welding at all levels as per specification/ drawing

Providing, fixing mild steel round holding down bolts with nuts & washer plate complete

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balconi railing, staircase railing and similar works including applying priming coat of approved steel primer : E.R.W tubes

Road Work

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres as per specification/drawing.

Cutting/ Filling of exisitng surface to make road profile and making good the same including supply of extra quantities of materials i.e aggregrates, moorum screening, red bajri and labour required for laying and compacting Water bound macadam (WBM-250 thick ) as per specification complete in all respect for axle load as specified in MORTH.

Providing and laying bitumen penetration macadam with hard stone aggregate of quality, size and grading as specified, with bitumen of suitable penetration of grade,including required key aggregate as specified, spreading coarse aggregate with the help of self propelled tipper tail mounted aggregate spreader and applying bitumen by a pressure distributor and then spreading key aggregate with the help of aggregare spreader complete, including consolidation with road roller of minimum 8 to 10 tonne capacity to achieve a specified values of compaction surface accuracy :For 75 mm compacted thickness in two layers using stone aggregate of size 63-41 mm graded @ 0.90 cum per 10 sqm key aggregate of size 20 mm graded @0.18 cum per 10 sqm. With paving asphalt grade VG-10 @ 68 kg/10 sqm.

Providing and laying standards seal coat of premixed fine aggregate ( passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG - 10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface, including rolling and finishing with road roller all complete.

Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used.

Providing and fixing factory made precast RCC units for heavy duty drain covers,pit covers trench covers etc. having concrete of strength not less than M-25, of size varying from 500 x 500 to 2500mm x2500mm approximately , reinforced with 8 mm to 12 mm dia T.M.T. bars, including providing 50 mm dia perforations where required, including providing edge binding with M.S. flats/ channels all as per drawing and direction of Engineerin- charge.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade

Providing weep holes in Brick masonry / Plain / Reinforced concrete abutment, wing wall / return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V:20H towards drawing face. Complete as per drawing and Technical specifications.

Providing and laying of Filter media with granular materials/stone crushed aggregates/brick aggregates /river bed materials satisfying the requirements laid down in clause 2504.2.2 of MoRT&H Specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and technical specification.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

MASONRY WORK

Brick work with fly ash bricks conforming to IS:12894,. (non modular) brick of class designation 10 in substructure & superstructure above plinth level in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with fly ash bricks of class designation 10, conformingio IS :12894 (non modular) in substructure & superstructure : Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

FINISHING

Internal Plaster

12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)

External Plaster

15 mm cement plaster of mix: 1:6 (1 cement: 6 coarse sand

Ceiling plaster & concrete surface

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade :New work (Two or more coats applied @ 1.43 ltr/ 10sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Providing neat cement punning.

Distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade. New work (two or more coats) over and including water thinnable priming coat with cement primer

Applying priming coat : With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat)(on ms surface like rolling shutter)

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture

Finishing internal Wall with (two or more coats) acrylic emulsion paint of approved brand and manufacture on new work to give an even shade on primer (Primer to be paid separately)

Applying one coat of primer of approved brand and as recommended by the paint manufacture, on wall surface.

Providing plaster drip course/ groove in plastered surface or moulding to R.C.C. projections

DOOR AND WINDOW

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. 30 mm thick plain PVC door shutters

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin- Charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)Second class teak wood 35 mm thick shutters

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :125x64x1.90 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :250x10 mm

Providing and fixing bright finished brass door latch with necessary screws etc. complete :250x16x5 mm

Providing and fixing bright finished brass handles with screws etc. complete: 125 mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing , fxing and making and finishing good after installation of M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. ii) Grill weighing above 16 Kg./sq.mtr along with painting with approved brand synthetic enamel paint complete in all respect.

FLOORING

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per anufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement: 18 mm thick

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic Anti-skid floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete: Size of Tile 600x600 mm

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

ALUMINIUM WORK

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer- in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion-Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer- in-charge complete : Upto 5mm depth and 5 mm width.

Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. complete : Anodized (AC 15) aluminium

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) :With float glass panes of 5.0 mm thickness

DRAINAGE

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

100 mm dia. R.C.C. pipe

250 mm dia. R.C.C. pipe

300 mm dia. R.C.C. pipe

600 mm dia. R.C.C. pipe

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1: 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 :8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size)inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design : Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg,(weight of cover 23 Kg and weight of frame 15 Kg).

Extra for depth for manholes : Size 90x80 cm - With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Same as above but with Inside size 120x90 cm and 90 cm deep including RCPC. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes :Size 120x90 cm - With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

WATER SUPPLY :

INTERNAL WORK - EXPOSED ON WALL Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-AL-PE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge :

Same as 14.01 for 4050 (50 mm OD) pipe

CONCEALED WORK, including cutting chases and making good the wall etc. Providing and fixing Polyethelene-Aluminium- Polyethelene (PE-AL-PE) Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge :

Same as 14.07 for 1620 (20 mm OD) pipe

Same as 14.07 for 2025 (25 mm OD) pipe

EXTERNAL WORK - EXPOSED ON WALL Providing and fixing Polyethelene-Aluminium- Polyethelene (PE-AL-PE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge : For 1216 (16 mm OD) pipe

Same as 14.11 for 2532 (32 mm OD) pipe

Same as 14.11 for 4050 (50 mm OD) pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

External work

80 mm nominal dia Pipes

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25 mm nominal bore

32mm nominal bore.

Providing and fixing brass stop cock of approved quality : 15 mm nominal bore

Providing and fixing PVC connection pipe with brass union-45 cm length, 15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms : 15 mm nominal bore

Providing and fixing of CP brass health Faucet with 1.2 m long PVC tube and wall hook HSW F160027 or approved equivalent, at all leads and lifts as per drawings,specifications and instructions of Engineer-in-Charge.

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

SANITARY INSTALLATION

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked black solid plastic seat and lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : Range of three urinal basins with 10litre white P.V.C.automatic flushing cistern

Same as 15.02 for Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required : White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm CP brass pillar taps of heavy quality.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer in- charge.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing toilet paper holder : C.P. Brass

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet- Sand cast iron S&S as per IS: 3989

Providing and fixing soil, waste and vent pipes : 100 mm dia Sand cast iron S&S pipe as per IS: 1729

Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes: for 100 mm dia pipe

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 100 mm dia pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 100 mm dia Sand cast iron S&S as per IS - 1729

Providing and fixing plain bend of required degree- 100 mm dia Sand cast iron S&S as per IS - 1729

Providing and fixing heel rest sanitary bend : 100 mm dia Sand cast iron S&S as per IS - 1729

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks of class designation 7.5 or above in cement mortar 1:4 (1 cement : 4coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 455x610 mm and 45 cm deep for single pipe line :

Supply fitting, fixing cast iron down pipes conforming to IS:3989-1970 and IS:1729-1964 in position with necessary clamps, nails including making hole in wall, floor etc. and cutting trenches in any soil through masonry concrete structures etc. if necessary and mending good damages including joining with jointing materials complete.[ Payment will be made on centre line measurement of the total pipe line including specials. Payment for specials will however be paid separately ] : 150 mm diameter pipe

Supplying fitting fixing C.I. Specials of down pipes in position with clamps nails etc. with jointing materials including cutting holes in masonry or concrete, mending good damages complete : CI Plain bend-150 mm diameter

Supplying fitting fixing C.I. Specials of down pipes in position with clamps nails etc. with jointing materials including cutting holes in masonry or concrete, mending good damages complete : CI Plain shoes : 150 mm diameter

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleat with CP brass screws (heavy quality) : 750 x 20 mm size

ROOF WATERPROOFING

Providing and applying combination of waterproofing & insulation, in the following sequence thru In-House Application Arm of Manufacturer by Spray apply an average 40 mm thick two component Hydro flouro carbon(CFC free), polymeric M.D.I based closed cell(96-98% as per ASTM D2856) multilayer, waterproof insulative polyurethane foam, and Providing and applying a sealer coat,, which is a single component cold applied elastomeric waterproofing coating with >=500% elongation confirming to ASTM C836 applied by a brush/roller in 2 coats and finished with loosely lay 120-150 GSM geotextile(non-woven polyester) over the Elastomeric coating. Laying protective slope with Sqm0 grade fibrated screed (admixed with integral liquid waterproofing compound conforming to IS:2645). Green stage saw cutting on the screed will be done in panels(3mx4m) with grooves 10mmx10mm. Finally the groove will be sealed with suitable elastomeric sealant.

All around on the roof, at the parapet wall junction, an angular fillet 50mm x 50mm shall be trowel applied in cement-sand mortar(cement, sand mortar shall be supplied by you) in 1:3 proportion. A latex based bonding agent should be added (10% by weight of cement) and also a glass cloth must be inserted around the junctions while the angle fillet is being constructed.

VERTICAL SURFACE TREATMENT

Surface preparation, minor cleaning works, removal of loose concrete, laitance, dust particles, etc and filling cracks with polymer modified mortar using latex based bonding agent. Removal of algae if present is to be done. Providing and applying a water based acrylic primer ,over the entire surface of the parapet walls(2 part primer : 1 part water). Providing and applying 2 coats of a high performance elastomeric coating, composed of acrylic emulsion polymers.

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 3 mm thick

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Hollow Metal Door (Without Fire Rated) : Providing and fixing of hollow metal door at all levels from ISO 9001-2000 certified manufacturer. All hollow metal genaral doors with or without vision panel. Pressed Galvanised steel Single / Double leaf to required sizes of approved make which consists of frame, shutter, infill and finish as detailed below and conforming to IS 277. Door frame shall be single rebate profile of size 100x57mm made out of 1.20mm thick galvanised steel sheet (18gauge). Door leaf should be 46mm thick fully flush double skin door with or without vision lite. Door leaf shall be manufactured from 0.8mm (22 gauge) minimum thick galvanised steel sheet. The internal construction of the door should be rigid with steel stiffeners / pads and reinforcement. The infill material shall be resin bonded honeycomb core. All doors should be factory prepped for receiving appropriate hardware and provided with necesssary reinforcement for hinges, locks, and door closets.All doors and frames shall be finished with etched primer coating, stove zinc phosphate primer and thermosetting polyurethane aliphatic grade paint of approved colour. The door leaf and frame shall have passed minimum 250hours of salt spray test.

Providing, fixing, installation, testing and commissioning of 7.0 m wide and 1.8 m height Motorised Retractable Gate of Gandhi automation /Smartpower automation or any equivalent make, having Opening Speed 15 Mt / Min, with Track System, Becon Alarm Light complete with all Accessories Type – Stainless Steel(SS304), with HEAD BOX containing AC Motors (Model no – SP ACM RSG) (Type – Sliding, 220 V AC + /- 13% / 50Hz / 370 Watts / 2 nos. Remote controller with sensor, Control Panel, Safety Devices Systems built in, Base plate, Limit switch, clutch key, ON/OFF power switch etc. & accessories all complete upto the satisfaction of EIC.

Providing at all heights, levels and locations pre colour coated Aluminium profile industrial troughed sheet of Alloy 31500/31000/40800, conforming to IS 1254, IS 737, IS 2676. The sheet shall be fixed using self drilling/ self tapping SS screws of size 5.5x65 mm with EPDM seal complete upto required pitch in horizontal, vertical or curved surfaces i/c cutting to size and shape where required as per specifications, detail drawings and direction of Engineer-in-Charge. The rate shall be inclusive of all screws, seal, ridge, labour, scaffolding, machinery for fixing and approved sealent where required etc. but excluding the cost of purlins, rafters and trusses. 0.91 mm thick, the profile detail width 1044/920 mm, cover width 1000/875 mm.

Supplying and Fixing complete in all respect.

Final commissioning and handing over.

Providing and fixing precoated aluminium sheet roofing accessories 0.91mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500 - 600mm)

Flashings/ Aprons.( Upto 600 mm)

Gutter (600 mm over all girth)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion : 160 mm diameter pipe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 160 mm dia

Providing and fixing polycarbonate sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation metre or as desired by Engineer‐in‐charge. The sheet shall be fixed using self drilling /self tappin screws with EPDM seal, and the joints shall be provided with aluminium strips at top and bottom as a seal complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.Pollycarbonate sheet 2mm thick solid type CSR‐13.27(V)d

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Dismantling & demolishing

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work.

Providing and fixing Glow studs of size 100x20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/-5) degress to base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge.

Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bilingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge.

Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm

Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm

Providing Retro-reflective regulatory sign board of size 900 mm dia meter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro -reflective sheeting as approved by Engineer-in-charge . The aluminium sheet to be riveted to M.S. frame of angle iron of size 40x40x4 mm. The boards will be fixed to 1 No. 50x50 mm square post made of M.S. angle 50x50x4 mm, 4 m long welded to the frame with adequate anti-theft arrangement .Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer-in-charge.

Providing and applying 2.5 mm thick road marking strips (retroreflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.

Providing ,supplying and transporting all materials required for construction of 35-40m span PSC box girder / steel girder bridge on open foundation over conveyor as per NIT drawing (protecting existing conveyor) and based on ground data, soil condition , particular specification of the tender documents including all preparatory works, POT and POT cum PTFE or ELASTOMERIC bearings, including launching / erection of staging work as required , Decking , wearing having nonskid surface,strip seal expansion joints , hand raillings , Kerbs, crash berrier , guard posts, drainage arragement over carriage way and foot path, service arragement for utilities, painting with noncorrosive paint as per fifth revision of MoRT&H (specification for road & bridges) to all exposed steel works and kerbs , protective work , 1.0mtr wide foothpath on both sides and all other item of works required and necessary for the complete construction of the bridge including curing, pour tensioning work but excluding works on approaches and approach slab (Excluding reinforcement, concrete, shuttering for foundation, girder and deckslab).

Supply, Fabrication and Erection of structural Steel works in single or builtup sections like joists,channels,pipes etc. as per drawing including tools, tackles, cutting, welding, consumables, assembly, bolts, permanent bolts, preparation of Fabrication drawings for all types of structures in buildings, pipe racks, platforms, towers or any other structure as specified in Technical specification and drawing and applying one prime coat, and with not less than two field coats. The thickness of the prime coat shall not be less than 75 microns and the total thickness of the two field coats shall not be less than 125 microns, complete in all respect.(Only for Bridge quantity)

ELECTRICAL Works

415V Power Distribution Board (PDB)-Supply, installation, testing, commissioning of:

PDBs- Supply

PDBs- Installation , testing & comiissioning

415V AC Lighting Panel (LP)-Supply, installation, testing, commissioning of:

415V LPs indoor-Supply

415V LPs indoor-Installation , testing & comiissioning

Feeder Pillar Box- Supply

Feeder Pillar Box- Installation , testing & comiissioning

415V LV Power Cables Supply, Laying & Terminations, gland, lugs and other accessories

3/C-16 Sq. mm (Al) -supply

3/C-16 Sq. mm (Al) -Installation , testing & comiissioning

4/C-16 Sq. mm (Al) -supply

4/C-16 Sq. mm (Al) -Installation , testing & comiissioning

4/C-95 Sq. mm (Al) -supply

4/C-95 Sq. mm (Al) --Installation , testing & comiissioning

1/C-2.5 Sq. mm (Cu) LIGHTING CABLE-supply

1/C-2.5 Sq. mm (Cu) LIGHTING CABLE--Installation , testing & comiissioning

Grounding & Lightning Protection System & Fitting & Accessories as required- Supply, installation, testing & commissioning

40MM dia MS Rod for main horizontal grid & riser- supply

40MM dia MS Rod for main horizontal grid & riser -Installation , testing & comiissioning

40MM dia & 3M long MS Rod with earth pit (EP) -supply

40MM dia & 3M long MS Rod with earth pit (EP) -Installation , testing & comiissioning

40MM dia & 3M long MS Rod with Lightning earth pit (LEP)-supply

40MM dia & 3M long MS Rod with Lightning earth pit (LEP)-Installation , testing & comiissioning

50x6 GS flat-supply

50x6 GS flat-Installation , testing & comiissioning

50x6 GS Earth Strip Horizontal & Vertical conductor and Test Link (lightning protection)-supply

50x6 GS Earth Strip Horizontal & Vertical conductor and Test Link (lightning protection)-Installation , testing & comiissioning

Vertical air terminal GI rod 1.5m with spike as vertical lightning conductor-supply

Vertical air terminal GI rod 1.5m with spike as vertical lightning conductor-Installation , testing & comiissioning

PVC Conduits Supply & installation

25mm dia PVC pipe-supply

25mm dia PVC pipe-Installation , testing & comiissioning

150mm dia PVC pipe-supply

150mm dia PVC pipe-Installation , testing & comiissioning

LIGHTING FIXTURE and Other fitting & accessories - Supply, installation, testing, commissioning : Indoor, outdoor & street Lighting

BN308C LED40S-4000Â L120 SL WH (1x34W LED, Philips or Eqvt)-supply

BN308C LED40S-4000Â L120 SL WH (1x34W LED, Philips or Eqvt)-Installation , testing & comiissioning

CEILING FAN, 80W( Bajaj or Eqvt)-supply

CEILING FAN, 80W( Bajaj or Eqvt)-Installation , testing & comiissioning

DN393B LED12S-6500PSU WH (1x12W LED, Philips or Eqvt)-supply

DN393B LED12S-6500PSU WH (1x12W LED, Philips or Eqvt)-Installation , testing & comiissioning

ROCHAK CIRRUS MINI TYPE (1x12W LED, Philips or Eqvt )-supply

ROCHAK CIRRUS MINI TYPE (1x12W LED, Philips or Eqvt )- Installation , testing & comiissioning

BY202P LED43S CW PSU PC SPD ((1x35W LED, Philips or Eqvt)-supply

BY202P LED43S CW PSU PC SPD ((1x35W LED, Philips or Eqvt))- Installation , testing & comiissioning

EXHAUST FAN, 50W(Bajaj or Eqvt)-supply

EXHAUST FAN, 50W( Bajaj or Eqvt)-Installation , testing & comiissioning

LIGHTING FIXTURE and Other fitting & accessories - Supply, installation, testing, commissioning :Outdoor Lighting

60W Wall mounted outdoor type decorative LED fixture (Bajaj or Eqvt) with other accessories-supply

60W Wall mounted outdoor type decorative LED fixture (Bajaj or Eqvt) with other accessories-Installation , testing & comiissioning

200W flood light LED fixture with other accessories-supply

200W flood light LED fixture with other accessories-Installation , testing & comiissioning

90W street LED fixture with other accessories-supply

90W street LED fixture with other accessories-Installation , testing & comiissioning

11M street lighting pole (540-SP-57) with accessories (JB, 2 nos. 3M long , 40mm dia GI Earthing rod and 50X6 mm MS earthing flat with earthing bolt and washer per pole ) **Provision of auto as well as manual operation along with applicable timer shall be considered for street lighting system.- supply

11M street lighting pole (540-SP-57) with accessories (JB, 2 nos. 3M long , 40mm dia GI Earthing rod and 50X6 mm MS earthing flat with earthing bolt and washer per pole ) **Provision of auto as well as manual operation along with applicable timer shall be considered for street lighting system.-Installation , testing & comiissioning

RECEPTACLE - Supply, installation, testing, commissioning

5 Amp, 240 V (p-p), 2-Pole, 3-Pin type socket with 5A modular type switch (RA type)-supply

5 Amp, 240 V (p-p), 2-Pole, 3-Pin type socket with 5A modular type switch (RA type)-.-Installation , testing & comiissioning

5/15 Amp, 240 V (p-p), 2-Pole, 5-Pin Universal type, socket with 16A modular type switch (RB type)-supply

5/15 Amp, 240 V (p-p), 2-Pole, 5-Pin Universal type socket with 16A modular type switch (RB type)-Installation , testing & comiissioning

3 nos. 5 Amp, 240 V (p-p), 2-Pole, 3-Pin, socket with 1 nos. 16A modular type switch for computer application (CS type)-supply

3 nos. 5 Amp, 240 V (p-p), 2-Pole, 3-Pin, socket with 1 nos. 16A modular type switch for computer application (CS type)--Installation , testing & comiissioning

5/15 Amp, 240 V (p-p), 2-Pole, 5-Pin Universal type, heavy duty, weather proof, dust proof, socket with 16A modular type switch (RB type)-supply

5/15 Amp, 240 V (p-p), 2-Pole, 5-Pin Universal type, heavy duty, weather proof, dust proof, socket with 16A modular type switch (RB type)-Installation , testing & comiissioning

SWITCHBOARDS & JUNCTION BOXES - Supply, installation, testing, commissioning

1 no. 6A switch (SA)-supply

1 no. 6A switch (SA)-Installation , testing & comiissioning

Junction Box with connector for lighting (JB) with T, Elbow, circular box etc.--supply

Junction Box with connector for lighting (JB) with T, Elbow, circular box etc.--- Installation , testing & comiissioning

3 nos. 6A switches with 1 no. 6A receptacle (SB)-supply

3 nos. 6A switches with 1 no. 6A receptacle (SB)- Installation , testing & comiissioning

Water supply for Service and Potable water .

Providing supply of all pipeline of various diameter for potable water supply

Supplying, fitting and fixing in position G.I. pipes of SAIL/TATA make for underground works with all necessary accessories,specials viz.socket, bend, tee, union, cross, elbow, nipple, short piece etc.including cost of all materials,jointing materials ,cutting pipes,making threads,cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed with two coats of painting on G.I. pipes and specials with bituminous paint complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories, specials.Payment for painting will be made seperately)

40 mm dia.

50 mm dia.

Suction pipe for Horizontal centrifugal pumps ERW, IS: 1239, Heavy GRADE 65 NB MS pipe. OD = 76.6 mm, Thk. = 4.5 mm

Discharge pipe for Horizontal centrifugal pumps upto the nearest ring main: ERW, IS: 1239, Heavy GRADE 50 NB MS pipe. OD = 60.8 mm, Thk. = 4.5 mm

Recirculation pipe for Horizontal centrifugal pumps upto UGR: ERW, IS: 1239, Heavy GRADE 50 NB GI pipe. OD = 60.8 mm, Thk. = 4.5 mm

Civil cost for construction of sluice valve, wash out chamber or Valve Pit for 50 NB

Providing and laying non-pressure NP3 class (medium duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete

450 mm dia R.C.C pipe -NP3 Spigot

90 0 Elbow at discharge pipeline IS: 1239; MOC: GI ; Size :65 NB

65 NB Gate Valve at Suction Pipeline as per IS 14846 suitable for class PN 1 (MPa), Flanged End MOC :CI with SS spindle

Flange (ANSI B16.5) IS: 1239; MOC: MS ; Size :65 NB

50 NB NRV at the discharge pipeline as per IS:5312 or API 600/ BS 1868 for class PN 1 (Mpa). Flanged end. MOC :CI with brass spindle

50 NB Gate Valve at Discharge Pipeline as per IS 14846 suitable for class PN 1 (MPa), Flanged End, MOC :CI with SS spindle

90 0 Elbow at discharge pipeline IS: 1239 (part 2); MOC: GI ; Size :50 NB

Equal Tee at discharge pipeline IS: 1239 (part 2); MOC: MS ; Size :50 NB

Flange (ANSI B16.5) MOC: MS ; Size :50 NB

50 NB Gate Valve at the recirculation pipeline as per IS 14846 suitable for class PN 1 (MPa), Flanged End, MOC :CI with SS spindle

90 0 Elbow at recirculation pipeline IS: 1239 (part 2); MOC: MS ; Size :50 NB

Installation of pipes, fittings, valves and speciality items inside the pump room.

Instrumentation including presure gauge (4 nos) level switches (2 nos), Water meter(2 nos), cables etc.

300 Litre PVC Water Tank

500 Litre PVC Water Tank

1000 Litre PVC Water Tank

2000 Litre PVC Water Tank

Excavation and back fill for pipeline

5 HP Centrifugal MonoBlock Single Stage Pump Set and motors.

15/5 Tonne Double Girder EOT Crane for LMV Building

Supply

Erection & Commissioning

Hand over

STP and ETP pipeline

Providing supply of all pipeline of various diameter for STP & ETP

Excavation and back fill for pipeline

Supply of MS Pipe

80 mm dia.

100 mm dia.

Supply of MS 90 Elbow

80 mm dia.

100 mm dia.

Supply of MS Tee

80 mm dia.

Supply of MS Flange

100 mm dia.

Supply of MS Blind Flange

100 mm dia.

Excavation and back fill for pipeline

Monorail at LMV

Monorail at HEMM

Mono rail at Crusher maintenance store and yard.

Bidder Name

Amount in Words

MIRAL INFRASTRUCTURE (BID ID -3112043)

SRC INFRA COMPANY PVT.LTD (BID ID -3111550)

MIRAL INFRASTRUCTURE (BID ID -3112043)