IMPROVEMENT TO CERTAIN SMQS AT 11 BRD AF STN OJHAR

Amount

Demolition of cement Concrete of any description and in any position not otherwise specifically provided for Complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L brushing cement slurry @ 3.00 Kg per Sqm on existing concrete surface complete all as specified and as directed.

M&L 25mm thick PCC 1:2:4 type B0( 12.50mm graged aggregate) finished even and fair surfaces complete all as specified and as directed.

M & L for coloured Non skid ceramic tiles 7 to 8 mm thick of colour patteren as approved and as per manufacturers catalouge (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm, in floor etc over 15mm thick screed bed with cement mortar 1:6 and set and jointed in neat cement slurry and pointed in white or coloured cement to match including jambs by making the mitred angles at corners all as specified and directed by Engr in charge

All as in item No. 05 herein before but vertical surface such as dado/ skirting including 10 mm thick backing coat in cement mortar 1:4 complte all as Specified and as directed.

M & L for coloured Non skid ceramic tiles 7 to 8 mm thick of colour patteren as approved and as per manufacturers catalouge (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 Sqm, in floor etc over 15mm thick screed bed with cement mortar 1:6 and set and jointed in neat cement slurry and pointed in white or coloured cement to match including jambs by making the mitred angles at corners all as specified and directed by Engr in charge

M & L for coloured glazed ceramic tiles 300 mm x450 mm & 7 - 8 mm thick on vertical surfaces of colour patteren as approved and as per manufacturers catalouge such as skirting, dados etc, set and jointed in neat cement slurry over and including 10 mm thick bedding layer/ backing coat in CM 1:4 complete and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-In-Charge. Note : Skirting shall be provided to match with colour and size of floor tiles provided in rooms.

M&L Kota stone slab 20-25mm thick polished of uniform colour as in floors including 15mm thick cement screed 1:6 and jointed with grey cement mixed with pigment to match the shade of the slab complete all as specified and directed. The exposed edges of treads shall be provided of full moulding and with three line grooves in each tread as directed. The treads and raisaers shall be provided with single piece kota stone.

S & F in Repair viterous china wash hand basin of size 550 x 400 mm, white colour flat back excluding taps, chain and plug and porcelean stopper but including brackets and CP waste fitting complete all as specified and as directed by Engineer-In-Charge

S&F in repairs vitreous china squatting pan Orissa pattern size 580x440mm white with CI P or S trap front or back inlet and integral foot rests including connection to trap to flush pipe etc complete including packing bottom and sides in PCC 1:2:4 B0 (12.5m graded aggregate) all as specified and as directed by Engineer-In-Charge.

S&F in repairs 10 litres capacity PVC Valveless symphonic action type flushing cistern high / low level white complete with inlet , ball valve float and handle including brackets and telescopic down flush pipes and jointing with WC complete complete all as specified and as directed by Engineer-In-Charge.

S&F in Repair PVC connection 15mm size with PTMT nuts, of length 600mm Complete all as specified and as directed by Engineer-In-Charge. Make : Prayag or equivilant.

S & F in Repair Fancy type Pillar taps , cast copper alloy , with capstan heads, chromium plated, screwed down high pressure fancy type of 15 mm bore size with or without lettered Hot or Coldwith long screwed shanks and flynuts , screwed for iron pipe and fixed Complete all as specified and as directed by Engineer-In-Charge.

S&F in Repair Cast copper alloy CP angle valve type stop cock with flange suitable for 15mm bore pipe screwed at both ends or high pressure with Capstan head confirming to Prayag /Seiko/ Parko Complete all as specified and as directed by Engineer-In-Charge.

S&F in Repair bib tap with flange of bore size 15mm, cast copper alloy, chromium plated, fancy type, with crutch or butter fly handle screwed down , screwed for iron pipe or for brass ferrule Complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing in repairs CP brass shower rose of size 125 mm saquare/circular as approved swivel type with CP extension rod 15mm dia and 200mm long suitable for 15mm bore pipe .Complete all as specified and directed by Engineer-in-charge.

S&F in Repair Cast copper alloy CP Concealed stop cock with flange suitable for 15mm bore pipe screwed at both ends or high pressure with Capstan head confirming to Prayag /Seiko/ Parko Complete all as specified and as directed by Engineer-In-Charge.

S&F in Repair Tubular towel rail, 20mm dia, D type, 60cm long between flanges of brass chromium plated fixed with and including CP brass screws in cleats (minimumwt 90gms)

S & F in repairs soap dish stainless steel of standards size and thickness minimum 2mm as approved by GE complete all as specified and as directed by Engineer-In-Charge.

S&F in Repair Stainless Steel Plate Rack SS 304 grade of size 31'' x 24'' x 10'' with using stainless steel sheet of 0.63mm thickness Fixed with Rawl plug and screw. complete Make : Prayag Cat No-P-340 Yr 2021 all as specified and as directed by Engineer-In-Charge. (Make Prayag, Nirali, Neelkamal,Bajaj,) Note : The plate rack shall be of 1st Quality and wt and composition of SS shall be as per IS.

S&F in Repair Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm and equivilant in (Make Nirali,Neelkamal, Bajaj) .complete all as specified and as directed by Engineer-In-Charge.

Taking down steel tubing of 15 mm dia bore and connections from walls and cellings or laid in floor including cleaning for refixing in same position (walls , ceiling, floors etc).

ditto All as item No. 27 but 20 mm bore.

S&F of 20mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors for chase cutting of Concealed for all the pipes complete all as specified. Note : Pipes shall be got tested before providing tiles by Pressure testing machine and got approved and any leakage seepage observed , the conctractor shall be redo the same without any extra payment.

S&F for Galvanised Iron tubes 20 mm dia medium grade with all fittings and fixtures such as bends , elbows ,tees ,short pieces , back nuts , connectors , diminishing pieces caps pegs and clamps union etc. laid in wall/floor/ceiling as in concealed work including cutting chase in wall and making good surface .

Supply and fixing in repair 500 Litre capacity Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position complete and all as specified and as directed by Engineer-in-Charge

S&F in repair 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete

S&F in repair 20mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

M & L 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement concrete type B-1 (1:2:4)complete all as specified and as directed by Engineer-In-Charge (Trap shall be sealed properly with the existing pipe and got tested by Filling with water)

M & L 75mm PVC (SWR) Multi Floor trap, plain with grating including jointing with solvent cement concrete type B-1 (1:2:4)complete all as specified and as directed by Engineer-In-Charge (Trap shall be sealed properly with the existing pipe and got tested by Filling with water)

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement including all excavation and complete embedded in PCC type B1 (20mm graded aggrgate) with CI MH cover and including jointing inlet and outlet pipes and and removal of excaveted materials upto 50 mtr distance.

Supply and fixing Low density polyethylene pipes (LDPE) of pressure rating 6 kg/ cm2 of 40 mm dia bore for wash hand basin Complete all as specified and directed by Engineer-in-charge.Make:Prayag

Demolition and breaking up drain pipes (Salt glazed ware , AC or RCC or PVC Pipes) of any dia including all fittings any size all as specified & as directed by Engr-in-Charge.

Supply and fix 110mm dia PVC(SWR ) single socket pipe , waste and vent pipes in any length with or without ears, with cement joints, fixed to walls complete all as specified and as directed.

Supply and fix 110mm dia PVC (SWR) single socket pipe , waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floor ncluding complete all as specified.

S&F 110 mm dia PVC (SWR) Bends any rediouse complete all as specified and as directed.

S&F 110 mm dia PVC(SWR) Branch Pipe , single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and as directed.

S&F PVC (SWR) 110mm dia vent cowl

Supply and fix 75mm dia PVC (SWR) pipe single socket , waste and vent pipes in any length with or without ears, with cement joints, fixed to walls complete all as specified and as directed.

Supply and fix 75mm dia PVC (SWR) Single socket pipe , waste and vent pipes in any length with or without ears, with cement joints, laid in floor/ trenches complete all as specified and as directed.

S&F 75mm dia PVC (SWR) Bends any rediouse complete all as specified and as directed.

S&F 75 mm dia PVC(SWR) Branch Pipe , single Socket ,ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and as directed.

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar, internal dia of pipe 150mm.Completed all as specified and directed by Engineer-in-charge.

Excavating in trenches, n exc 1.50m wide and n exc 1.50m in depth; for foundations, etc. or for manholes etc not exc 10 Sqm on plan and not exc 1.5m in depth and getting out in soft/loose soil.Complete all as specified and directed by Engineer-in-charge.

M & L for reinforced cement concrete pipes class NP-3 laid in jointed complete with collers ,bore of pipe 150mm Complete all as specified and directed by Engineer-in-charge. Make : Hindustan / Universal or equvilant confirming to IS.

M & L for cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate, bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in bore of pipe 150mm.Complete all as specified and directed by Engineer-in-charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick with soils.Complete all as specified and directed by Engineer-in-charge.

Removing surplus excavated material (Soils) to distance of exc. 250 m bu n. exc. 500 m and depositing where directed at a level n. exc. 1.5 m above the starting point. complete all as specified and as directed by Engineer-In-Charge

M & L for cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in foundations, filling and mass concrete including filling around pipes.Complete all as specified and directed by Engineer-in-charge.

M & L for cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in Coping/Channels in side the manholes/ benching etc including formwork and weathering/ slightly rounded or champhered angle making the surface even and fair Complete all as specified and directed by Engineer-in-charge.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc.

M&L for Precast Man hole covers type B1 1:2:4 (20 mm graded aggregate) of size asper site requirement including finishing the surfaces even and smooth including making holes and inserting MS conduit pipe with provision of MS Round bar 10mm dia made in shape for lifting the MH cover 2 nos with each cover Complete all as specified and directed by Engineer-in-charge

M&L framework of Flat iron minimum 3mm thick for MH covers all round of RCC 1:2:4 with sharp edges and grindiing the all corners including all welding and welding the TMT bar all as directed. Including all painting etc (RCC 1:2:4 and TMT bars shall be measured in separate items as mentioned above)

Cutting into existing manholes forconnecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required (internal dia of pipe 150mm )Complete all as specified and directed by Engineer-in-charge.

S&F framed work such as grills of approved design used square bar of frame of MS hellow square tubes framed guard bars etc., and Flat iron for MH covers all round of RCC 1:2:4 with sharp edges and grindiing the all corners including all welding and welding the TMT bar andn similar work conforming to Fe-410-0 or Fe-310-0.compete all as specified as directed by Engineer -in -charge

Forming jambs in Cement concrete 1:4 to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complet all as specified and as Directed .

M&L Machine cut cudappah stone slab 20mm to 25mm thick over and including 15mm thick cement screed bed in CM 1;6 laid and jointed in grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing Complete all as specified and as directed by Engineer-In-Charge.

M&L for drilling holes for pipes etc in cadappa/granite including RCC slab nexc 25mm dia and n exc 150mm depth

Demolition of reinforced cement concrete in any position like roofs, floors other than ground floors , beam , staircases , landings , chajjas,projections, facias and similar suspended work or reinforcement cut as required to facilate demolition for portions ordered to be dismanttled up to 15 m height including forwork and necessary saftey measuresor as directed by Engr in charge

M&L for reinforced cement concrete type B1 (1;2;4) nominal mix using 20 mm graded broken stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, shelves and the like.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers,lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed by Engineer-In-Charge.

S&F mild steel TMT bar of 10 mm dia and over cut to length bent to shape required including cranking and binding with mild steel annealed wire not less than 0.9 mm dia.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar includin gall quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L Brick work with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM1 : 6 all as specified and directed by Engr-in-Charge

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick built in cement mortar 1:4 complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for 15 mm thick cement plaster in CM 1:6 on brick surface finished even and smooth without using extra cement including in patches Complete all as specified and directed by Engineer-in-charge.

M&L for 15 mm thick cement plaster in CM 1:4 on brick surface finished even and smooth without using extra cement including in patches Complete all as specified and directed by Engineer-in-charge.

All as per item No 70 above but in 10mm thick CM 1:3 as in ceiling finished even and smooth without using extra cement including in patches Complete all as specified and directed by Engineer-in-charge.

M &L for preparation of newly plastered surfaces at ceiling and applying the 3 coat of white wash.Complete all as specified and directed by Engineer-in-charge.

M &L for preparation of newly plastered surfaces at walls and applying the 2 coat of Oil bound distemper over 1 coat of primer Complete all as specified and directed by Engineer-in-charge.

M&L preparation of newly plastered surface of wall and applying 2 coats of cement based paint on on ecoat of alkali resistant primer complete.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 Sqm each compete all as specified as directed by Engineer -in -charge

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but n.exc. 4 Sqm each compete all as specified as directed by Engineer -in -charge .

Taking down shutters of any description exc1 Sqm but n exc 2 Sqm each compete all as specified as directed by Engineer -in -charge

S&F 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

S&F Powder Coating (minimum thickness of powder coating 50 micron) aluminium frame for wndows, ventilators with one or morerebates including joining cleat for fixing etc. complete all as specified

S&F Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of windows (sliding) including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointedmechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws allcomplete as per architectural drawings and thedirections of Engineer-in-Charge.rates are deemed to be included sliding arrengments for sliding window, including locking arrengement, powder coated aluminium handle 01 Nos with each leaf, tower bolt with 2 nos each leaf, 2 Nos hewavy duty aluminium hinges with each leaf and 01 No powder coated stay for each leaf with casement window and moving arrengement for louvers in case of louvers type ventilators

S&F 4.00mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane including small pices as required for louver ventilators.

S&F Galvanised wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with GI wire staples

S & F for 35mm thick second classhard wood, factory made Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats (Shutters shall be brought at site without primer and got approved by Engr-in-Charge/ GE.)

S & F 35 mm thick second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive gauze, glass etc., (with sash bars) divied into into sqare and half portion panel upto middle rail and will be provided with 12mm thick pre laminated board laminated on both side and edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizess of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a)compete all as specified as directed by Engineer -in -charge

S&F Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

S&F Supply and fixing 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856 complete all as specified by the manufacturer and as per directions of Engineer- in-charge (Make-Rajashri/Sintex/ Accura)

S & F 100 mm MS butt hinges medium weight cold rolled mild steel compete all as specified as directed by Engineer -in -charge

S & F 150 mm aluminium anodised barrel tower bolts of extruded section, ISI marked compete all as specified as directed by Engineer -in -charge

S & F 150 mm extruded aluminium alloy handles , fabricated type, anodised, ISI marked compete all as specified as directed by Engineer -in -charge

S & F Continuous (piano) hinges, width of flaps 30mm mild steel, bright finish or electrogalvanised

S&F 100mm Aluminium anodised, barrel tower bolts of extruded section and fixed

S&F 100mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws

S & F 300 mm long and Mild steel Chromium plated sliding door bolts, plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed compete all as specified as directed by Engineer -in -charge

M & L two coats of synthetic enamel paint over one coat of pink primer on wood or wooden based surface exc. 10cm width or girth including preparation of new or previously untreated surfaces.compete all as specified as directed by Engineer -in -charge

S & F in repair 18mm thick prelaminated particle board exterior grade medium density, one side with decorative choice lamination and the other side balancing white lamination as in panels of partitions/ cup board shelves including providing wooden brackets minimum 25mmx25mm and long as depth of cupboard for support of laminated boards and the like fixed in wooden frame with wooden beading compete all as specified as directed by Engineer -in -charge

S & F mild steel spring 300mm for door, ordinary rat tail rod pattern springs, including roller and roller plate including welding as required for steel frame compete all as specified as directed by Engineer -in -charge ( work shall be carried out in MD Qtrs/ OTM accns in different locations of Domestic/ Technical area as per site requirements upto 4 storieyed building)

S & F in repairs curtain rod of metalic 25 mm dia Harrison rails, mild steel, chromium plated including long projected bracket of heavy section both side fixed in position by drilling holes in walls and fixed the brackers with rawl plug and steel screw compete all as specified as directed by Engineer -in -charge

Complete Removal of existing treatment from old brick/concrete surface on walls and applying two coat of Oil bound distemper using roller, brushes including in patches over a coat of alkali resistant primer complete all as specified and as directed by Engineer in charge

Complete removal of existing treatment and applying 2 coats of cement base paint over one coat of alkali resistant primer on old surface of wall cmplete.

Preparation of old surfaces by scrapping down smoke soot, moulds, moss and efflorescent salts and greasy spots,removing nails and make the surface smoth by using sand paper and fill the holes with putty etc., and applying two coat of white wash on ceiling complete all as specified and as directed by Engineer in charge

Taking down carefully existing bitumen tarfelt including plastering upto 15mm thick cleaning the surface and make free of dirt, foreign particles, laitance followed by grinding all protrusions to make surface modulated and removing all foreign materials / Bitumenous primer completely , cleaning and washing the existing surface of roof/slab, terraces including flashings and junctions of parapets/Curb walls etc and as directed by Engineer-in-charge. Note : (i) Contractor will not thrown the debris and taking down material from roof will make suitable arrangement to get down the material from roof. (ii) If taking down of plaster is exceeding 15mm than PCC and plaster both shall be measured under ser item No 20 below (iv) Removing of the rubbish to a distance outside MoD land at own arrangement of Contractor.

M&L for providing ement concrete 1:2:4 Type B0 (Using 12.5mm graded stone aggregate) as in bed plate/roof kerb/PCC padding and haunching etec all as specified and directed by Engr in Charge Note : PCC shall be laid in slope and thickness shall be averege (minimum average thickness 25 or as oer site requirement for maintaing the slope) as per site including filling in depression by providing concrete bench marks for maintaining th perfect slope to drain out the rain water as directed by Engr-in-Charge. No hand mixing is allowed, mixing shall be at ground floor and mixed materials deposited on roof by Manually/ mechanically to acheive the proper strength and workmen ship.

M&L for rendering 5 mm thick in CM 1:3 on concrete surfaces mixed with water proofing compound @ 0.12 ltr per bag of cement or as per manufacturer instruction and finishing the surfaces even and smooth without using extra cement. Note:- (Supply only water proofing compound shall be measured and paid separately).Complete all as specified and directed by Engineer-in-charge.

M&L providing cement slurry @ 3Kg per sqm on existing roof surface before laying PCC/ Plaster.

Supply only liquid water proofing compound

M&L for cleaning the newly plastered surfaces throughly with wire brushes and providing water proofing treatment all as given here in after (a) Bituminous primer @ 0.3lit per Sqm conforming to IS-3384-1986 (b) 3 mm thick APP polymer modified moply FP of M/S TEXSA Ltd or M/S STP Ltd or ASIAN PAINTS of Hydrostop Tiki Dan of M/s Tikki tar Ltd with minimum wt 3.0 Kg per square metre membrane (one layer) laid by torch application method. (c ) Applying two coat of bituminous based aluminium paint @ 0.20 Kg in two coats (total in two coats) per square metre over membrane. Complete all as specified and directed by Engineer-in-charge. (d) The overlaps of APP shall be SSR part 1 and APP shall be laid by expert/ skilled workers only, bitumen based aluminious paint applied by brushes only.

M & L for cement concrete type C2 (1:3:6) (40 mm graded broken stone aggregate) 75 mm thick as in plinth protection and finish even and fair all as directed by Engr in Charge

M&L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound of Grade A

M & L Gi wire 4mm dia for Drying/Hanging Cloths complete all As specified and as directed.

M&L for Repair to RCC structure using micro concrete all as per manufactureres instructions, as descripbed below and as specified and directed. (a) chipping off existing loose and damaged/craked concrete/plaster surfaces at location decided by engr-in-charge to depth n.exc 100mm using peneumatic tools or with light chiseling & wire brush, descale the exposed surfaces of reinforcement with wire brushes removing all loose rust scales from rebar blowing all loose dust with blower and washing concrete surfaces. A coat of alkali rust converting primer to be applied on the reinforcement bar surfaces. (b) Welding additional reinforcement bars where dia of existing bar is found reduced than specified limit as directed. Note : Reinforcement will be measured and paid separately. (c) Applying coat of anticorrosive protective coating on both old & new reinforcement bars surfaces as per manufactureres instructions. (d) Applying a coat of epoxy resin concrete bonding agent to exposed concrete surfaces and rebars. (e) Providing polymer modified ement mortar in specified composition for making manufactureres instructions (Thickness varies from 25mm to 100mm) Note : - (i) The rate for necessaryscaffolding & formwork is included in the quoted rate. (ii) The work will be carried out upto G+4 floors

S & F mild steel TMT Bars of 5mm dia and over upto and including 10mm in stirrups spacers and binding cut to length bent to shaps required,including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securibg with clips

Taking down existing copper/aluminum point wiring (light/ fan/ socket or power points) complete including (fittings such as switches, ceiling roses, pendents, regulators, sockets, Light fitting etc including wooden battens /casing /capping and conduit etc and making good disturbed surface of walls, ceilings and floors etc. complete all as specified & as directed by Engineer-in-Charge.

Disconnecting electric supply and taking down the existing sub main wiring and making good the disturbed surface complete all as specified and directed by Engineer-In-Charge.

Disconnecting electric supply and taking down the Light fitting any type and making good the disturbed surface complete all as specified and directed by Engineer-In-Charge.

Taking down existing DBs , incldding MCB,s complete all as specified

M&L for Point wiring with 1.5 Sqmm (nominal area) PVC FRLS insulated sheathed copper stranded conductor cable run in and including on surface of wall/ celling/ floor ,in existing conduit including 1.5 Sqmm PVC(FRLS) insulated copper earth continuity conductor connected to common earth dolly and including MS/sunken boxes with modular inner & surface plate suitable for housing modular switches, sockets, fan regulators etc for one light/ fan/ call bell point controlled by one 1- way switch, complete all as specified & as directed by Engineer-in-Charge. One light point controlled by one switch

All as per above item no 116 but for One fan point controlled by one switch

All as per above item no 116 but for One exhaust fan controlled by one switch

All as per above item no 116 but for One Bell point controlled by one Push button

All as per above item no 116 but for One 3 pin socket outlet 5 Amps on same board

All as per above item no 116 but for One 3 pin socket outlet 5 Amps on Independent board

All as per above item no 116 but with two runs of 2.5 sqmm cable and one run of 1.5 sqmm cable as earth wire for one 3 pin socket outlet/power point 15 Amp controlled by one switch .

Supplying and fixing Modular switch , one way, 16 amps, one Module of Make:- Ancher Roma/Legrand/ Crabetree.

Supplying and fixing Modular socket 16 amps-6 pin multipin, 2 Module of Make:- Ancher Roma/Legrand/ Crabetree.

Modular switch one way 6 Amp,1 Module , Make Legrand / Anchor Roma/Crabetree .

Supplying and fixing Modular socket, 6 amps-2/3 pin combined, 2 Module, Make Legrand / Anchor Roma/Crabetree .

Supply & Fix Modular Fan regulator electronic step type 230 V 2 Module. Make :Legrand/Anchor/Roma.

Supply & Fix Ceiling rose surface type, PVC/Polycarbonate isolated body size 50x28 mm two to three terminals. Make : Anchor/Leader.

Supply & Fix bell push flush type 5 Amp moduler

Supply & Ding Dong AC 230 Volts single pole. Make : Anchor/Press Fit

Supply and fix Lamp Holder complete all as specified and directed by Engineer-in-Charge.

Supply and fix saving LED LED bulb 7 watt cat No 7 W CDL B-22 6500 K complete all specified and directed by Engineer-In-Charge

Supply and fix in repair decorative ultra slim square profile linear Light Linea lighting fixture extruded polycarbonate, environmental friendly, energy efficient ready to use pack 20 W LED 6000K, complete all as specified and directed by Engineer-in-Charge. MAKE : Crompton, Phillips / HAVELLS.

Supply and fix in repair decorative ultra slim square profile linear Light Linea lighting fixture extruded polycarbonate, environmental friendly, energy efficient ready to use pack 10 W LED 6000K, complete all as specified and directed by Engineer-in-Charge. MAKE : Crompton, Phillips / HAVELLS.

Supply and fix in repair decorative ultra slim square profile linear Light Linea lighting fixture extruded polycarbonate, environmental friendly, energy efficient ready to use pack 5 W LED 6000K, complete all as specified and directed by Engineer-in-Charge. MAKE : Crompton, Phillips / HAVELLS.

Supply and fix in repair Sheet metal enclosure for DB’s SPN, with 200 amps rated bus bar , 8 way ,240 volts IP 43 glazed door. Make Legrand Cat. Nos 507621 Or equivalent Make :Siemens/L&T, Complete all as specified & as directed by Engineer-In-Charge

Supply and fix in repair MCB SP 6 to 32 Amps 240 volts 10 KA C series. MCB with separate short circuit indication type Make Legrand Cat. Nos 408595 Or equivalent Make :Siemens/L&T, Complete all as specified & as directed by Engineer-In-Charge

Supply and fix in repair MCB SPN 6 to 32 Amps 240 volts 10 KA. Make Legrand Cat. Nos 408617 Or equivalent Make :Siemens/L&T, Complete all as specified & as directed by Engineer-In-Charge

M&L wiring for circuit/ sub main wiring of 2x6 Sqmm + 1x6 Sqmm earth wire, alongwith eart wire PVC (FRLS) insulated copper conductor, single core, 1100 v grade cable in surface/ recessed as required in PVC casing caping complete all as directed by Engr -in- Charge.

S&F ceilling fan 1200 mm sweep operated on 230/240V AC Single phase electric supply complete including connecting with 3 core stranded copper conductor cable cordas as per manufacture recommendation from ceiling rose to exhaust fan connector including writing MES No. on Exhaust fan white synthetic enamelled paint complete all as per specified and directed by Engr-in- Charge .

Taking down carefully ceilling fan any type and size of any make and sweep dismantlling blades , carried out reapir as reqd for functioning of fan incl winding , replacement of capacitor etc and scraping down old paint , rust, dirt, grease etc cleaning and preparation of motors and blades surfaces, and spray painting with two coats of approved apcolite enamel paint and refixing the same after completion of B/R work all as directed by Engr-in-chargead.

supply,install,testing and commissioning of out door type cbical metering panel board outer shell made out of 3.15 mm thich MS sheet of size not less than 600X600XX300 mm and MS angle iron frame size 35X35X6 mm mounted on Wall/Floor withsuitable size of nut, bolt and washer , frame factory fabricated withfront openable 3 phase , 4wire 415 volt, 50 Hz, including taking down old existing electric meter and refixing the same in new metering panel incl all electrical connections complete all as specified and directed by Engr-in-charge and compriseing with following TPN aluminium bus bar 200 Amp insulated with colour coded heat shhrikable sleeve and shall be mounted on suitable size 'F' class insulators Incoming MCCB 63 Amps 16 KA ,415 Volts, 50 Hz, FP-01 No Out going MCB SP 40 Amp-05 No Space for installation of electric meter-05 No LED Indicating lamp -01 set of three

M/S SAMEER SUBHASH PATANI (BID ID -3203006)

M/S PRAMOD SURESHCHANDRA AHER (BID ID -3202647)

Santhi Enterprises (BID ID -3202466)