PROVN OF CHAIN LINK FENCING FOROPEN PERIMETER AT SUKNA MIL STN UNDER GE SUKNA

Amount

Excavation in post holes and/or similar holes each not exceeding 0.50 Cum in soft/loose soil, getting out, removing surplus spoil/ soil to a distance not exceeding 50 metre away from the premises, complete all as specified and as directed.

M&L for cement concrete type B-2 (1:2:4) using 40 mm graded stone aggregates in foundation filling and mass concrete, complete all as specified and directed.

Supply only of chain link fencing made of mild steel any size and type galvanised wire, complete all as specified and as directed (Dia of wire and size of mesh shall be as approved by the GE).

Fixing only chain link fencing of any size including line wires, any mesh, size and type, to any type of standards, rails, straining bolts etc, inclding provision of binding wire, complete all as specified and as directed.

M&L for mild steel comprising of the angle iron, flat iron etc using steel conforming to Fe-290 Gde E-165 as in posts & struts in fencing including cutting tops to shape as diected, drilling holes, notching for wire etc & embedding in the concrete, fillets (for securing wire-mesh etc) and similar works, also including necessary bolting/ riveting, complete all as specified and as directed.

S&F Mild steel bars 10mm dia round bars and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips conforming to Fe 290 (Gde- E-165) for holding the chain link fencing in the position etc, complete all as specified and as directed.

S&F Mild steel screw bolts (machine made) (diameter of neck 11 to 15 mm) with hexagonal or square heads at one end or screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 05 cm but n. exc 10 cm long, complete all as specified and as directed.

S&F Galvanised, 2 strand, steel barbed wire, 2.24 mm dia, barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails, straining bolts including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured separately ), complete all as specified and as directed.

M&L for preparing of New steel & iron surfaces of any description, not otherwise described, not exceeding 10cm in width or girth and applying two coats of black bitumenous over a coat of Red oxide zinc chrome primer, complete all as specified and as directed.

M & L for preparing of New steel & iron surfaces of any description, not otherwise described, not exceeding 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of Red oxide zinc chrome primer, complete all as specified and as directed.

M & L for preparing of New steel & iron surfaces of any description, not otherwise described, exceeding 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of Red oxide zinc chrome primer, complete all as specified and as directed.

Excavating in trenches n.exc. 1.50m wide and n.exc 1.50m in depth for foundation etc and not exec 10Sqm on plan & n.exec 1.5 metre in depth for independent holes etc and getting out in soft/loose soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with approved earth/soil etc, complete all as specified and directed.

Removing excavated material to a distance not exc 50.00 metre and depositng where directed at a level n.exc 1.5m above the stating point, complete all as specified and as directed.

Use and waste of formwork to sides of concrete foundations/footings, bases of columns, raft and raft-beams, sides & soffits (if any) of foundation and plinth beams and similar work, vertical or to batter, for rough finished flat surface of concrete, complete all as specified and as directed.

M&L for reinforced cement concrete type B-1 (1:2:4) using 20 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc, complete all as specified and as directed. Note:- (i) Reinforcement and Form Work shall be measured and paid for seperately.

Use and waste of formwork to square, rectangular or polygon sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete, complete all as specified and as directed.

M&L for reinforced cement concrete type B-1 (1:2:4) using 20 mm graded stone aggregates as in columns, pillars, piers, posts and struts, complete all as specified and as directed. Note:- (i) Reinforcement and Form Work shall be measured and paid for seperately.

M&L 20mm thick granite (of any type) tiles machine cut in skirting/ dado laid over cement 15 mm thick screed bed in cement mortar (1:6) and jonted with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete all as specified and directed.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc, complete all as specified and as directed.

M&L TMT bars 8mm dia and over upto and including 10mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc, complete all as specified and as directed.

M&L for the Framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc [using rolled mild steel Fe-290 (Gde - E-165)] complete, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing, complete all as specified and as directed.

S&F concertina coil razor type fixed with galvanised `J` clips, with angle iron of the following specification :- (a) Dia of coil when unstretched -600mm (b) No of circles- 50 per coil (c) No of razor per RM- 160 (d) Weght of each coil- 8 kg (e) Coverage per coil- 6 mtr (f) Central Core wire: Made from high tensile spring steel core wire confirming to IS-4454 duly hot dipped galvanised (confirming to IS-2629) with diameter 2.59mm+ 0.05mm, UTS 145-160 kg/sqm zinc coating 250-300/per sqm (g) Strip- Electro galvanised steel strip 0.50mm +0/.02 mtr thick, width 19mm (before wrapping on central core wire) confirming to IS--1573. Zinc coating-120 gm/sqm and bituminised dipped, width of barbs 11.50mm, pitch of barbs 25.4mm+0.20mm (h) Harndle and spikes to be provided as required.

SUN SHINE OVERSEAS PVT.LTD.

MS ORIENT ENGINEERING WORKS

M/S B D ENTERPRISE