Construction of Fish Landing Centres at Periyakalapet, Nallavadu and Construction Expansion of fishing harbour at Thengaithittu under Centrally Sponsored Scheme Component of Pradhan Mantri Matsya Sampada Yojana PMMSY. Project 3 Construction Expans

Amount

Earth work in excavation by mechanical means (Hydraulic excavation) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10sqm on plan) including getting out and disposal of excavated earth, lead upto 50m and lift upto 1.5m -all kinds of soil

Extra rates for quantities of works, executed - in or underwater and /or liquidmud,including pumping out water as required

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, onsolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m

Supplying and filling in plinth with river sand under floors, including watering ,ramming consolidating and dressing complete

Supplying and filling with gravel (excluding rock) in layers not exceeding 20cm in depth , breaking clods , watering , rolling each layer with 1/2 tonne roller, or wooden or steel rammers and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes capacity including all leads and lift (Payment will be made based on level measurement)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level - 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size)

Centring and shuttering including strutting , propping etc. and removal of form work for - retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.

Providing and fixing upto floor five level precast cement concrete string or lacing courses , copings, bed plates, anchor blocks, plain window sills, shelves , louvers, steps, stair cases, etc. including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering , shuttering complete - 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering , shuttering , finsishing and reinforcement - All work upto plinth level 1:1.5:3 (1cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness) , including attached pilasters, buttresses , plinth and sting courses , fillets , columns , pillars , piers , abutments , posts and struts etc. upto floor five level excluding cost of centering , shuttering , finishing and reinforcement - 1:1.5:3 (1 cement : 1.5 coarse sand : 3graded stone aggregate 20mm nominal size)

Centering and shuttering including strutting , propping etc and removal of form for - foundations, footings, bases of columns etc for mass concrete

Centering and shuttering including strutting , propping etc and removal of form for - Suspended floors , roofs , landings , balconies and access platform

Centering and shuttering including strutting , propping etc and removal of form for - Lintels , beams , plinth beams, girders, bressumers and catilevers

Centering and shuttering including strutting , propping etc and removal of form for - Columns , Pillars , Piers , Abutments , Posts and Struts

Centering and shuttering including strutting , propping etc and removal of form for -Weather shade , Chajjas, corbels etc., including edges

Steel reinforcement for R.C.C.work including straightening , cutting , bending , placing in position and binding all complete upto plinth level - Thermo -Mechanically treated bars (TISCON / VIZAG / IISCO / SAIL / JSW) Fe - 415 or more

Steel reinforcement for R.C.C.work including straightening , cutting , bending, placing in position and binding all complete above plinth level - Thermo - Mechanically Treated bars (TISCON / VIZAG / IISCO / SAIL / JSW) Fe - 415 or more

Providing anticorrosive treatment to HYSD reinforcement with fusion bonded epoxy coating the rate includes cost of anticorrosive coating including cost of powder , sand blasting, cleaning , induction , heating , depreciation of machinery etc, wastage in cut length of bars, provision of wooden battens between rows of coated bars , cover to work bush pins / bar bending machines etc - for bars of 20mm to 32 mm diametre - conforming to IS 13620 -1993

Providing anticorrosive treatment to HYSD reinforcement with fusion bonded epoxy coating the rate includes cost of anticorrosive coating including cost of powder, sand blasting, cleaning , induction , heating , depreciation of machinery etc, wastage in cut length of bars , provision of wooden battens between rows of coated bars , cover to work bush pins / bar bending machines etc - for bars of 8mm to 16 mm diametre - conforming to IS 13620 -1993

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work , using cement content as per approved design mix , including pumping of concrete to site of laying but excluding the cost of centering , shuttering , finishing and reinforcement , including admixtures in recommended proportions as per IS : 9103 to accelerate, retard setting of concrete , improve workability without impairing strength and durability . Note:- Cement content considered in this item is @ 330 kg / cum. Excess or less cement used as per design mix is payable or recoverable separately. - All work upto plinth level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work , using cement content as per approved design mix , including pumping of concrete to site of laying but excluding the cost of centering , shuttering , finishing and reinforcement , including admixtures in recommended proportions as per IS : 9103 to accelerate, retard setting of concrete , improve workability without impairing strength and durability . Note:- Cement content considered in this item is @ 330 kg / cum. Excess or less cement used as per design mix is payable or recoverable separately. - All work above plinth level upto floor V level

Extra for providing richer mixes at all floor levels - Note:- Excess / less cement over the specified cement content used is payable / recoverable separately - Providing M-30 grade concrete instead of M-25 grade BMC / RMC . (Note:- cement content considered in M-30 is @ 340 kg / cum)

Extra for providing richer mixes at all floor levels - Note:- Excess / less cement over the specified cement content used is payable / recoverable separately - Providing M-35 grade concrete instead of M-25 grade BMC / RMC . (Note:- cement content considered in M-35 is @ 350 kg / cum)

Add for using extra cement in the items of design mix over and above the specified cement content therein

Extra for adding Recron 3S or equivalent 12 mm fibre as fibre reinforcement in concrete oncrete at the rate of 909 gm per cum of concrete including the cost of fibre

Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 3.5 in foundation and plinth in - cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. 3.5 in foundation and plinth in - cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S (non modular ) bricks of class designation 3.5 in superstructure above plinth level upto floor five level in all shapes and sizes in - cement mortar 1:4 ( 1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in superstructure above plinth level upto floor V level - cement mortar 1:3 (1 cement : 3 coarse sand)

Extra for providing and placing in position 2 nos 6mm dia M.S.bars at every third course of half brick masonry

Providing and fixing 18mm thick gang saw cut, mirror polished (premoulded and prepolished) machine cut for kitchen platforms,vanity counters,window sills,facias and similar locations , of required size, approved shade,colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing,curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels - Raj nagar plain white marble / Udaipur green marble / Zebra black marble - area of slab over 0.50 sqm

Providing and fixing stone slab with table rubbed , edges rounded and polished , of size 75x50 cm deep and 1.8cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6mm nominal size) and finished smooth - White agaria mable stone

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) - Kiln seasoned and chemically treated Padak wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows, and clerestory windows, including ISI marked M.S.pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately , all complete - Kiln seasoned and chemically treated Padak wood - 35 mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick - Kiln seasoned and chemically treated Padak wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick - Float glass panes - 4mm thick glass pane

Providing 40 X 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bots, nuts and wooden plugs and embeddings in cement concrete block 30 x10 x 15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc.complete - 100 x 60 x 2.50 mm

Providing and fixing aluminium sliding door bolts , ISI marked , anodised ( anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade , with nuts and screws etc complete - 300 X 16 mm

Providing and fixing aluminium tower bolts , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS :1868) , transparent or dyed to required colour or shade , with necessary screws etc. complete - 150 x10 mm

Providing and fixing aluminium tower bolts, ISI marked , anodised (anodic coating not less than grade AC 10 as per IS :1868) , transparent or dyed to required colour or shade , with necessary screws etc. complete - 100 x10 mm

Providing and fixing aluminium handles , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade,with necessary screws etc, complete - 125 mm

Providing and fixing aluminium handles, ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade,with necessary screws etc, complete - 75 mm

Providing and fixing aluminium hanging floor door stopper , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc complete - Single rubber stopper

Providing and fixing aluminium hanging floor door stopper , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc complete - twin rubber stopper

Providing and fixing PTMT handles with necessary screws etc complete - 125x34 x 24 mm weighing not less than 23 gms

Providing and fixing PTMT Tower bolts with 12 mm one piece rod inside and necessary screws etc., complete - 152 x42x18 mm weighing not less than 60 gms

Providing and fixing of 65mm Godrej Navatal lock of 6 levers etc complete

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Supplying and fixing rolling shutters of approved make, made of required size M.S.laths, interlocked together through their entire length and jointed together at the end by end locks , mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to ISS :4454 -part 1 and M.S.top cover of required thickness for rolling shutters - 80 x 1.20mm M.S.laths with 1.25 mm thick top cover

Steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel (grade 304) railing made of hollow tubes, channels, plates etc., including welding ,grinding. Buffing, polishing and making curvature (whereever required) and fitting the same with necessary stainless steel nuts and bolts complte. i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab withsuitable arrangement (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.,)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 ( 1 cement : 4 coarse sand) - 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1cement :3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) , of approved make (Jhonson / Asian / Somany / Nitco) in all colours, shades of size 300 x 600 mm as approved in skirting , risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 300x600 mm

Providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of commercial quality conforming to IS : 15622, of approved make (Bell / Johnson / Regency / Somany / Naveen / Asian) in colours such as white, Ivory, Grey, Fume red brown ,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including pointing the joints with white cement and matching pigment etc., complete

Providing and laying Soluble Salt vitrified floor tiles of size 600 x600 mm (thickeness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 of approved make (Nitco / Somany / Johnson / Asian ) in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) , including grouting the joints with white cement and matching pigments etc., complete - size of tile600x600mm

Painting top of roofs with bitumen of approved quality @ 17kg per 10 sq.m impregnated with a coat of coarse sand at 60cum per 10 sq.m including leaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete - with residual type petroleum bitumen of grade VG-10

Providing and laying pressed clay tiles (as per approved pattern 18mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound , laid over a bed of 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete

Lime concrete terracing on roofs of required thickness laid to fall with 25mm nominal size brick aggregate and 50% lime mortar 1:2 (1 lime putty : 2 surkhi) rammed and finished with gur and belgiri treatment complete including rounding of junctions with Parapet wall complete

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, (i) Single socketed pipes - 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to S:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - Single tee with door - 110x110x110mm

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to S:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - bend 87.5 degree - 110mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - shoe (plain) - 110mm shoe

Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50mm hard wood plugs , screwed with M.S. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc., complete - 110mm

Providing & fixing precoated galvanised iron profile sheets (size, shape, and pitch of corrugation as 0.50mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both sides of the sheet and polyster top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired. The sheet shall be fixed using self drilling / self tapping screws of size (5.5 x 55 mm) with EPDM seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins , rafters and trusses and including cutting to size and shape wherever required

12mm cement plaster of mix -1:4 ( 1 cement : 4 fine sand)

15mm cement plaster on the rough side of single or half brick wall of mix - 1:4 (1cement : 4 fine sand)

12mm cement plaster finished with a floating coat of neat cement of mix - 1:4 (1 cement :4 fine sand)

12 mm cement plaster of mix 1:5 (1 cement : 5 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix 1:5 (1 cement : 5 fine sand)

6 mm cement plaster of mix - 1:3 (1 cement : 3 fine sand)

Neat cement punning

Providing and applying white cement based primer (JK primaxx two or more coats) undercoat for exterior cementitious surface.

12mm thick plain cement mortar bands in cement mortar 1:4 (1cement : 4 fine sand) - re raised band

Colour washing such as green, blue or buff to give an even shade - New work (two or more coats) with a base coat of whiting

Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface - water thinnable cement primer

Finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade - New work (two or more coats applied @1.67ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10sqm)

Finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade - New work (two or more coats applied @1.43 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10sqm)

Painting steel work with deluxe multi surface paint to give an even shade. Two or more coat applied @ 0.90 ltr / 10 sqm over an under coat of primer applied @ 0.80 ltr / 10 sqm of approved brand and manufacture

Applying priming coat - with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Applying priming coat: with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works.

Wall painting with plastic emulsion paint - Commercial of approved brand and manufacture to give an even shade - two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacutre to give an even shade - Two or more coats on new work

Providing and fixing finished brass hard drawn hooks and eyes -150mm

Making plinth protection with bricks of class designation 3.5 laid on edge in cement mortar 1:6 (1 cement : 6 coarse sand) with 12 mm thick bed of cement mortar 1:6 ( 1 cement : 6 coarse sand) over 75 mm bed of dry brick aggregate 40mm nominal size rammed. Consolidated and grouted with fine sand and the top of bricks pointed with cement mortar 1:3 (1 cement : 3 fine sand)

Half brick masonry with bricks of class designation 7.5 in superstructure above plinth level upto floor V level in cement mortar 1:4 (1 cement : 4 coarse sand)

Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal two diagonals interwoven with horizontal wires, of barbed wire 9.38kg per 100m (minimum ) between the two posts fitted and fixed with G.I staples , turn buckles etc.complete (cost of posts struts, earth work and concrete work to be paid for separately):- Payment to be made per metre cost of total length of barbed wire used.-with G.I barbed wire

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in oposite direction for 10cm length and drilling holes upto 10mm dia etc..complete

Providing and fixing water closet squatting pan (Indian type W.C.pan) with 100 mm Sand Cast Iron P or S trap, 10 litre low level white P.V.C flusing cistren, including flush pipe , manually controlled device (handle lever) conforming to IS : 7231 , with all fittings and fixtures complete , including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C.pan of size 580x440mm with integral type foot rests.

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps ,32 mm C.P.brass waste of standard pattern , including painting of fittings and brackets ,cutting and making good the walls wherever required - white vitreous china flat back wash basin size 550x400 mm with single 15mm C.P. brass pillar tap

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps ,32 mm C.P.brass waste of standard pattern , including painting of fittings and brackets ,cutting and making good the walls wherever required - white vitreous china anglet back wash basin size 600x480 mm with single 15mm C.P. brass pillar tap

Providing and fixing Stainless steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I.brackets and stainless steel plug 40mm , including painting of fittings and brackets, cutting and making good the walls wherever required - kitchen sink without drain board - 610x460 mm bowl depth 200mm

Providing and fixing white vitreous china laboratory sink with C.I.brackets, C.P.brass chain with rubber plug , 40mm C.P.brass waste and 40mm C.P.brass trap with necessary C.P.brass unions complete , including painting of fittings and brackets, cutting and making good the wall wherever required - size 450x300x150mm

Extra for using coloured W.C.pan instead of white W.C.pan - Orissa pattern W.C.pan 580x440mm

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm or 340x410x265mm sizes respectively

Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete - flexible pipe - 32mm dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete - flexiple pipe - 40mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P.brass screws and washers complete

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing - oval shape 450x350mm (outer dimensions)

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing - rectangular shape 1500 x 450 mm

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour - 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88mm, weighing not less than 170 gms

Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 25mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 32mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and the cost of cutting chases and making good the same including testing of joints complete (Concealed work including cutting chases and making good the walls etc.) - 20 mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings this included jointing of pipes & fittings with one step ASTM solvent cement , trenching refilling & testing of joints complete (External work) - 25 mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings this included jointing of pipes & fittings with one step ASTM solvent cement, trenching refilling & testing of joints complete (External work) - 40 mm nominal outer dia pipes

Providing and fixing gun metal gate valve with C.I.wheel of approved quality (Screwed end) - 25mm nominal bore

Providing and fixing gun metal gate valve with C.I.wheel of approved quality (Screwed end) - 32mm nominal bore

Providing and fixing gun metal gate valve with C.I.wheel of approved quality (Screwed end) - 40mm nominal bore

Providing and fixing ball valve (brass) of approved quality , high or low pressure , with plastic floats complete - 25mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI: 12701 marked , with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank - Circular Tank

Providing and fixing C.P.brass bib cock of approved quality conforming to IS: 8931 - 15 mm nominal bore

Providing and fixing C.P.brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms - 15 mm nominal bore

Providing and fixing C.P.brass stop cock (concealed ) of standard design and of approved make conforming to IS :8931 - 15mm nominal bore

Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931- 15 mm nominal bore

Providing and fixing PTMT pillar cock of approved quality and colour - 15 mm nominal bore , 107 mm long, weighing not less than 110 gms.

Providing and fixing PTMT grating of approved quality and colour - circular type - 100mm nominal dia

Providing and fixing PTMT swivelling shower, 15mm nominal bore, weighing not less than 40 gms

Providing and fixing PTMT Soap dish holder having length of 138 mm , breadth 102 mm, height of 75mm with concealed fitting arrangements , weighing not less than 106 gms

Providing and fixing square - mouth S.W.gully trap class SP -1 complete with C.I. grating brick masonry chamber with water tight C.I.cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50kg and frame to be not less than 2.70 kg as per standard design - 150x100mm size P type - with common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing square - mouth S.W.gully trap class SP -1 complete with C.I. grating brick masonry chamber with water tight C.I.cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50kg and frame to be not less than 2.70 kg as per standard design - 180x150mm size P type - with common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Making soak pit 2.5 m diameter 3 m deep with 45 x 45 cm dry brick honeycomb shaft with bricks of class designation 75 and 110mm dia UPVC pipe (type B) 1.8 m long complete as per stadard design with F.P.S.bricks

Providing and fixing on wall / column face unplasticed - PVC soil and waste pipes (type - B) conforming to IS : 13592- 1992 including jointing with seal ring conformation to IS : 5382 leaving 10mm gap for thermal expansion - single socked pipes -110mm diametre

Providing and fixing on wall face / column face unplasticised - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 - 1999 including jointing with seal ring conforming to IS :5382 leaving 10mm gap for thermal expansion - Single tee with door - 110 x110x110mm

Providing and fixing on wall face / column face unplasticised - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 - 1999 including jointing with seal ring conforming to IS :5382 leaving 10mm gap for thermal expansion - Single tee without door - 110 x110x110mm

Providing and fixing on wall face / column face unplasticised - PVC mould fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend 110 mm

Providing and fixing on wall / column face unplasticised - PVC soil and waste pipes (type B) conforming to IS :13592 - 1992 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single socketed pipes 75mm diameter

Providing and fixing on wall / column face unplasticisd - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single tee with door - 75x75x75mm

Providing and fixing on wall / column face unplasticisd - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single tee without door - 75x75x75mm

Providing and fixing on wall / column face unplasticisd - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Bend 75 mm

Boring, providing and installing bored cast -in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring , with bentonite solution and temporary casing of appropriate lenghth for setting out and removal of same and the lenghth of the pile to be embedded in the pile cap etc. all complete , including removal of excavated earth with all lifts and leads (length of pile for payment shall be measured upto bottom of pile cap) - 300 mm dia piles

Boring , providing and installing bored cast -in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring , with bentonite solution and temporary casing of appropriate lenghth for setting out and removal of same and the lenghth of the pile to be embedded in the pile cap etc. all complete , including removal of excavated earth with all lifts and leads (length of pile for payment shall be measured upto bottom of pile cap) - 450 mm dia piles

Conducting standard penetration test as per IS 2131 - 1981 using split spoon sampler and drive weight assemply at required depth in all type of soil including hire charges for machinery and labour etc., all complete - 10 to 20 metre

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100 % polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation

Providing and fixing factory made single extruded WPC (Wood Polymer composite) solid door / window / Ceosetory windows and Other frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 ( Suspension Grade) calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frames density of 750 kg / cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compresssive strength of 58N/sq.mm, modulus of elasticity 900 N/sq.mm and resistance to spread of flame of class A category with property of being termite / borer proof, water / moisture proof and fire retardant and fixed in position of with M.S hold fast/lugs /SS dash fasteners of required dia and length complete as per direction of Engineer-in-charge (M.S hold fast/lugs or SS dash fastners shall be paid for separately) Note: For WPC solid door / window frames, minus 5mm tolerance in dimensions i.e. depth and width of profile shall be acceptable . Variation in profile dimension on plus side shall be acceptable but no extra payments on this account shall be made. - Frame size 65 x 150 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawl strength of 1800 N (Face) and 900 N (Edge), minimum compressive strength 50N/sq.mm , modulus of elasticity 850 N/sq.mm and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S.screws, all as per direction of Engineer-in-charge. (Note: Stainless steel butt hinges and necessary S.S.screws shall be paid separately) - 35mm thick

Earth work in rough excavation and dressing up in embankement by using machinery for roads , flood banks, marginal banks and guide banks or filling up ground depression within a initial lead of 50m and lift upto 6m in all kinds of soil (Payment shall be made based on levels)

Providing and fixing 110 mm dia PVC pipes (4kg / cm2) in weep holes including cement concrete 1:5:10 (one cement : 5 sand : 10 graded stone aggregate ) and filling of pebbles etc.,

Supplying and placing in position HDPE cement bags filled with sand for breach closing / diversion arrangement. The cost includes the cost of empty HDPE bags , labour charges for filling the bags and placing in position , removing the bags from site after completing the work etc., complete

Collection and supply of stone boulders at Various weights including the charges for conveyance , pre - weighing the loaded vechile and post - weighing the empty vehicle and placing the boulders to the required slope and section by using suitable machinery including handling and packing charges , crane charges etc., complete . The payment will be made based on weight basis. The quantity will be counter checked by way of volumes computed based on pre-levels and post-levels of the section and the volume thus computed will be arrived in weight after reducing for the corresponding voids depending on the size of stone boulders . This rate shall include the costs of formation of approch track for tranportations of materials men and machinery for the placing and dumping the boulders in position for groins / sea protection wall / rock revetment as per sectional drawing and harbouring works also etc., complete. The specific gravity of stone shall be from 2.90 to 3.02.Core after deducting 30% voids. Using 5kg to 100

Collection and supply of stone boulders at Various weights including the charges for conveyance , pre - weighing the loaded vechile and post - weighing the empty vehicle and placing the boulders to the required slope and section by using suitable machinery including handling and packing charges , crane charges etc., complete . The payment will be made based on weight basis. The quantity will be counter checked by way of volumes computed based on pre-levels and post-levels of the section and the volume thus computed will be arrived in weight after reducing for the corresponding voids depending on the size of stone boulders . This rate shall include the costs of formation of approch track for tranportations of materials men and machinery for the placing and dumping the boulders in position for groins / sea protection wall / rock revetment as per sectional drawing and harbouring works also etc., complete. The specific gravity of stone shall be from 2.90 to 3.02.Toe after deducting 30% voids. Using 100kg to 300 Kg

Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end) - 20mm nominal bore

Providing and fixing C.I. non return valve (PN 1.6) conforming to IS 5312 and ISI marked, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 50 mm dia

Constructing masonry Chamber 60 x 60 x 75 cm inside with 35 class designation brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter 160 mm bottom diameter and 180 mm deep (inside) with chained lid and R.C.C. top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design - with brick class designation 35.

Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 metres (average lead 50 metres) including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections.

Excavation for roadwork in soil with hydraulic excavator of 0.9cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections and transporting to the embankment location with all lifts and lead upto 1000m.

Earthwork in excavation of foundation of structure as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remainging earth locally for road work - by mechanical means - depth upto 3m (Ordinary soil)

Construction of granular sub-base by providing close graded material, mixing in a mechanical mix plant at OMC, carriage of mixed material to work site, spreading in uniform layer with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 of MoRTH specification, 4th Revision - by plant mix method - for grading II material.

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in sub-base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density - Using vibratory roller. (As per MoRTH specification, 4th Revision)

Providing and applying primer coat with bitumen emulsion on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means. (As per MoRTH specification, 4th Revision)

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg. per sqm. on the prepared bituminous / granular surface cleaned with mechanical broom. (As per MoRTH specification, 4th Revision)

Providing and laying bituminous macadam with hot mix plant of capacity not less than 40 -60 TPH using crushed aggregates of specified grading premixed with bituminous binder, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 507.7 of MoRTH specification, 4th Revision, to achieve the desired compaction. - using grade II metal and bitumen 60/70 grade.

Providing and laying bituminous concrete with HMP of capacity not less than 40 to 60 TPH using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per clause 509 of MoRTH specification, 4th Revision, complete in all respects - Using grade-II material.-Bitumen 60/70

Reinforced cement concrete m-20 mix with stone aggregate 20mm nominal size mechanically mixed and vibrated for bed plates exlcuding steel reinforcement, but including centering and shuttering, laid in position.

Steel reinforcement for R.C.C. works including bending, binding and placing in position - Thermo Mechanical Treated Bars (TISCON / VIZAG / IISCO / SAIL/JSW) Fe - 415 or more

Plain cement concrete m-15 mix with stone aggregates 20mm nominal size mechanically mixed and vibrated in foundation upto a depth of 1.50 metres below ground level and/or 1.50 metres above ground/bed level.

Cement concrete 1:4:8 mix with stone aggregate 40mm nominal size in foundation upto a depth of 1.5 metres below ground level and upto height of 1.5 above ground/bed level.

Providing and filling in foundation trenches and at the back of abutments, wing walls etc. and below pipe bed in layers not exceeding 150mm thick including watering and compacting including all lead and lifts. - Good local sand free from earth.

Providing and laying of hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes.

Earth work in excavation for foundation of structures as per drawings and technical specifications, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material - Oridnary Soil - Mechanical Means - Depth upto 3 metres including the cost of labour hire charge of hydraulic excavator and overhead charges.

Earth work in excavation for foundation of structures as per drawings and technical specifications, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material -Oridnary Soil - Mechanical Means - 3 metres to 6 metres depth including the cost of labour, hire charge of hydraulic excavator and overhead charges.

Sand filling in foundation trenches as per drawing and technical specification including the cost of labour, material and overhead charges.

Pile load test on single vertical pile in accordance with IS:2911 (Part -IV) - Initial and routine load test

Providing and laying of filter media with granular materials / stone crushed aggregates satisfying the requirements laid down Clause 2504.2.2. of MoRT&H specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and technical specifications.

Supplying and filling with Quarry rubbish including watering, ramming, consolidating and dressing etc., complete as directed by the Engineer-in-charge

Hire charges for engaging front end loader 1 cum capacity for clearing the accumulated soild waste and loading to the tipper / tractor, for disposal at the stock yard. The rate shall include the hire charges for machinery, operating staff, fuel charges, lubricants etc., complete as directed by the Engineering-in-charge.

Providing, hoisting and fixing precast RCC cover slabs for drain (upto plinth level) of length varying upto 1.80m and varying thickness from 100mm to 200mm including the cost of required centring, shuttering and finishing smooth with neat cement punning on the exposed surfaces but excluding cost of reinforcement, with 1:1.5:3 ( 1 cement ; 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). The rate is inclusive of all taxes

Supplying and fixing 600 x 600mm C.I cover with frame for Manhole cover

Dredging in the Inner Channel from the existing bed level upto the level of (-5)m in all kind of soils like clay, silt, sand, gravel, sewage and slush but excluding isolated boulders and hard rock and other materials encountered using the same Cutter Suction dredger. The dredged spoil is to be dumped on land within a lead distance of 1 Km measured from the discharge end of the dredger and as directed by Engineer in charge from time to time by laying suitable pipeline as required. Bunding work has to be done using suitable machineries for dumping the dredged spoil on land. The length, width, depth, location to be dredged shall be decided by the Engineer-in-charge, as per site condition prevailing at the time of dredging and the same shall be adhered to by the contractor. The rate quoted is to include GST. Any Government Agency appointed by the Engineer will be the Third Party Survey Agency for carrying out the Hydrographic surveys prior to commencement of dredging operation, at interim and on completion of work to ascertain the quantity of work done for making payment to the contractor. (The payment for the Third Party Survey Agency shall be paid by the Employer)

Constructing cast-in-situ RCC diaphragm wall by providing and laying machine batched, machine mixed, self compacting, ready mix reinforced cement concrete, tramie controlled, of M 35 grade using minimum 428 kg cement per cum of concrete including providing and mixing required admixtures in recommended proportions as per IS:9103, as approved by the Engineer-in-charge, for achieving 150-200mm slump, for diaphragm wall having required thickness as per approved structural design not exceeding 1000 mm, in panels of required depth and lengths as per approved drawing, including constructing necessary guide walls as required and as specified including boring in all kinds of soils and rocks, including working in or under water and / or liquid mud, in foul conditions and pumping or bailing out of water and removing slush, including disposal of earth / rock / slush etc. for all leads and all lifts, including preparing, providing and re-circulating bentonite slurry in the trench as and when required for all depths, including agitating bentonite slurry during trenching etc. providing and fixing stop ends or form tubes, upto the required depth of diaphragm wall including extracting the same after casting, including chipping off the bentonite adulterated concrete or unsound concrete upto the cut off level for obtaining the sound concrete, dressing undulations on the exposed face of diaphragm wall after excavation by chipping / chiseling etc. including filling the depression / cavities with sound concrete etc. complete, and as directed by the Engineer-in-charge, including providing recess for bearing plates and fixing insert boxes for inclined rock anchors etc. complete as per specification and approved design and as directed by the Engineer-in-charge, but excluding the cost of reinforcement and inserts. (Rates include cost of all inputs of labour, material and T & P, cost of handling, lifting and placing in position the reinforcement cage in the trench, including the additional cost of welding the reinforcement bars etc. involved in the work and all other incidental expenditure for completing the work. However, the actual area of the diaphragm wall, correct to two places of decimal, from design bottom level to the design cut off level (including portion anchored in the rock upto the design bottom level) only shall be measured for payment - Excess / less cement used for design mix including the extra cement required for under water concreting is payable / recoverable separately. The rate is inclusive of all taxes)

Sri Pathy Associates Private Limited