Construction of Convention Centre cum State Guest House at Guwahati, Assam

Amount

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. Up to a depth of 2.00 M below the existing ground level. In ordinary soil

Extra over item no.1.1(A) above for each 1 m depth or part thereof beyond the initial depth of 2m. 2 m to 3 m

Earth/ sand filling in plinth in layers not more than 150 mm thick including necessary carriage, watering, ramming etc. comlpete as directed and specified including payment of land compensation, forest royalti, sales tax and other duties and taxes as may be necessary. With river sand or silt (predominality non plastic) by truck carriage including loading and unloading.

Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary forest royelty, sales tax, land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc. complete as directed and specified. (a) Within Guwahati city only

Plain cement concrete works with coarse aggregate of sizes 13 mm to 32 mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, curing complete (Shuttering where necessary shall be measured and paid saperately). In prop 1 cement :4 Sand :8 coarse aggreget by volume

Plain cement concrete floor base in prop 1:3:6 laid in alternate bays as specified with coarse agg. of size 13 mm to 32 mm including dewatering if necessary, and curing etc. complete. 100 mm thick

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately). Using Batching Plant/ RMC/ Truck mounted batching plant including Transit Mixer and Concerete Pump. In Sub Structure, Using admixture, plasticizer etc. M-30 grade concrete

M-35 grade concrete

M-80 grade concrete

In Super Structure, Using admixture, plasticizer etc. M-30 grade concrete Gr. Floor

Extra over item above for each subsquent floor or part thereof above 1st floor level. Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

9th Floor/ Terrace

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately). Using Batching Plant/ RMC/ Truck mounted batching plant including Transit Mixer and Concerete Pump. M-80 grade concrete Gr. Floor

Extra over item above for each subsquent floor or part thereof above 1st floor level. Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

9th Floor/ Terrace

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Providing form work of ordinary timber planking so as to give rough finish including centering , shuttering, struting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0m & removal of the same for in situ reinforced concrete and plain concrete work in: Foundations, footings, bases of columns, pile cap, raft and mass concrete work etc. Using 25 mm thick plank

Columns, Pillars, Posts and Struts Suqare, Rectangular, polygonal in plan or any shape like Tee/L etc. having plane vertical face. M-80 grade concrete. Using 25 mm thick plank Upto Gr. Floor

Extra for each subsequent floor or part thereof above the first floor level as mentioned in item above Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

9th Floor/ Terrace

Sides and soffits of Beams, beam haunchings, cantilever girders, bressumers, lintel and horizontel ties. For depth not exceeding 1.0 M Using 25 mm thick plank

Extra for each subsequent floor or part thereof above the first floor level as mentioned in item above Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

9th Floor/ Terrace

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantilever slabs, chajjas, balconiess and the like. Floor etc. above 200 mm in thickness. Using 25 mm thick plank

Floor etc. upto 200 mm in thickness. Using 25 mm thick plank Gr. Floor

Extra for each subsequent floor or part thereof above the first floor level as mentioned in item above Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

9th Floor/ Terrace

Vertical surfaces such as walls (any thickness), parapet walls, partition, walls of septic tank, inspection pit and the like including attached pilasters, butresses, plinth and string courses. Using 25 mm thick plank Upto Gr. Floor

Extra for each subsequent floor or part thereof above the first floor level as mentioned in item above Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

9th Floor/ Terrace

Staircase with sloping or stepped or stepped soffits including riser and stringers but excluding landing. Using 38 mm thick plank. Upto Gr. Floor

Extra for each subsequent floor or part thereof above the first floor level as mentioned in item above Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

Extra for each subsequent 1.0 M height or part there of beyond the initial height of 4.0 M as mentioned in item no.9

Providing form work of ordinary timber planking and removal of the same in edge of slab and breaks in floors and walls etc. of in situ reinforced concrete work upto first floor level. Thickness not exceeding 200 mm Basement Floor

Gr. Floor

Extra for each subsequent floor or part thereof above the first floor level as mentioned in item above Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic 1000 mm dia piles boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used.

750 mm dia piles

600 mm dia piles

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Group of two or more piles upto 50 tonne Safe capacity Initial test (Test Load 2.5 times the Safe capacity)

Routine test (Test Load 1.5 times the Safe capacity)

Filling sunken floor with broken jhama brick bats and sand including compacting and supplying of materials complete as specified and directed for all levels. Ground Floor

Extra cost for lifting of brickbats and sand for filling of sunk floor for each subsequent floors above the ground floor as directed and specified. Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. In Sub-structure upto plinth level including dewatering if necessary In proportion 1:6

Autoclaved Aerated concrete Block work using Grade-I AAC block of compressive strength 40Kg/cm2 having dry density 550 to 650 Kg /Cum conforming to IS-2185 Pt-3 or pt-4 in cement mortar of prop 1:4 including racking out joints and curing complete as specified & directed. (Superlite/BrikOlite/Green AAC Block) In superstructure above plinth level up to 1st floor level. Gr. Floor

Extra for AAC block walling for each subsequent floor or part thereof above the 1st floor level Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

9th Floor/ Terrace

Autoclaved Aerated concrete Block work using Grade-I AAC block of Size 625x240mm of different thickness of compressive strength 40Kg/cm2 having dry density 550 to 650 Kg /Cum conforming to IS-2185 Pt-3 or pt-4 in cement mortar of prop 1:4 including racking out joints and curing complete as specified & directed. (protruding rod is to be provided at every 3 course interval and will be measured and paid separately) (Superlite/BrikOlite/Green AAC Block) In superstructure above plinth level up to 1st floor level. For 125mm thick wall Basement Floor

Gr. Floor

Extra for AAC block walling for each subsequent floor or part thereof above the 1st floor level Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at every fourth course of half brick masonry.

40 mm thick cement concrete floor consisting of 25 mm under layer of cement concrete in prop 1:3:6 (1cement : 3coarse sand : 6 coarse aggregate of 12.5 mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement : 1coarse sand : 2 coarse aggregate of 10 mm and down) finished with a floating coast of neat cement finish using cement slurry for bond @ 2.75 kg. per sqm. of floor area, wearing layer is to be laid in panels including curing complete as directed.

Providing polished Ceramic wall Tiles of approved quality, size, shape and thickness not less than 8 mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 Cement: 3 Coarse sand), including cutting where necessary finished with flush pointing with fix-A Tile (Choksey/ Sika/ Pedelite/ Rouf/ White cement slurry) mixed with approved pigment to match the shade of tiles complete at all levels as specified and directed (coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Wall means both interior and exterior walls). Delux Range (Somany/ Orient/ Nitco/ Varmora Make) of size 300mm x 600mm and above

Providing SUN ROCK HIGH CTS/ DEVI paver block/Tiles of concrete grade M30 or above of approved quality, size, shape of specified thickness over a leveling bedding layer of 30 mm compacted sand over a base course of WBM or PCC (Base course to be paid separatly) including cutting where necessary finished with spreading, sweeping jointing sand and compacting the pavers using vibrating compactor as specified and directed. SUN ROCK HIGH CTS/ DEVI paver block/Tiles 80 mm thick

Kota stone slab flooring of 18 mm thick over 20 mm thick base of cement mortar 1 : 6 (1 cement : 6 coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete. 550mm x 550mm

Kota stone slab of 18 mm thick in riser of steps, skirting, dado and pillars laid with 10 mm thick cement plaster 1 : 3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete. 550mm x 550mm

Providing Polished Granite Slab of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/ Sika/ Pedelite/ Rouf)/ White cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed (Cement plastering to be measured and paid separatly) (coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). Delux Quality With Fix-A-Tile (Choksey/ Sika/ Pedelite/ Rouf)

Providing and laying Vitrified tiles with water absorption less than than 0.08% and confirming to IS:15622, of approved make, in all colors and shade, laid on 20mm thick Cement mortar 1:4 (1 Cement:4 coarse sand), including grouting the joints with white cement and matching pigments etc, complete 600x600 Vitrified tiles of QUTONE or equivalent

Providing, fitting and fixing Laminated abrasion resisitant wooden flooring from Uniproducts (India) Ltd. of thickness not less than 8.2 mm laid on existing concrete floor with under layer of approved transparent polythene and foam sheet to make the floor surface even and sound free complete as directed and directed. Unitex AC4 Brand

Providing edge moulding to 18 mm thick Granite stone, including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Providing and laying C.C. pavement (TRIMIX) of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately).

Providing and laying 100% synthetic carpet of density 1500 Gm./Sqm and of approved shade as per manufacturer specification including matching and finishing joint etc. complete in all respect as per the drawing and the direction of E/I. the item include 40 mm c.c. flooring and providing and laying 12 mm thick coir under lay below the synthetic carpet.

10 mm cement plaster in single coat on fair side of brick/concrete walls for interior plastering upto 1st floor level including aries or rounded angles not exceeding 80mm grith and finished even and smooth including curing complete as directed. In cement mortar 1:6 Basent. Floor

Gr. Floor

Extra over item above for interior plastering above 1st floor level for every additional floor or part there of including curing complete as directed. (a) On single coat plaster. Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

9th Floor/ Terrace

15 mm cement plaster in single coat on rough side of single or half brick walls for interior plastering upto 1st floor level including aries or rounded angles not exceeding 80mm grith and finished even and smooth including curing complete as directed. In cement mortar 1:6 Basent. Floor

Gr. Floor

Extra over item above for interior plastering above 1st floor level for every additional floor or part there of including curing complete as directed. (a) On single coat plaster. Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

9th Floor/ Terrace

15 mm cement plaster in single coat on rough side of single or half brick walls for exterior plastering upto 1st floor level including aries or rounded angles not exceeding 80mm grith and finished even and smooth including curing complete as directed. In cement mortar 1:6 Gr. Floor

Extra over item above for exterior plastering over wall for every additional floor or part there of beyond 1st floor level including curing complete as directed. (a) On single coat plaster. Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

9th Floor/ Terrace

15 mm cement plaster in single coat on rough side of single or half brick walls for exterior plastering upto 1st floor level including aries or rounded angles not exceeding 80mm grith and finished even and smooth including curing complete as directed. In cement mortar 1:4

Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) M/F Suspended ceiling which includes G.I. perimeter channels of size 0.55 mm thick (having one flange of 20 mm and another flange of 30 mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screw, at 610 mm c/c. Then suspending G.I. intermediate channels of size 45 mm (0.9mm thick with two equal flanges of 15mm each) from the soffit with at 1220mm c/c with ceiling angle of width 25mm x 10mm x 0.55mm thick fixed to soffit with G.I. cleat and steel expansion fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two equal flangesof 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 457mm c/c, 9.5mm /12.5mm tapered edge Gypboard (conforming to IS:2095-1982) is then screw fixed to ceiling section with 25mm long drywall screw at 230mm c/c. Screw fixing done mechanically either with screw driver or drilling machine with suitable attachment. Finally, the boards are to be jointed and finished so as to have a flush look which includes filling and finishing the tapered and suqre edges of the boards with jointing compound, joint paper tape and two coats of drywall topcoat suitable for Gypboard complete at all levels as specified and directed. (For light fittings, providing opening for doors, window, ventilators etc. cut out made with frame of perimeter channel supported suitably to be measured and paid separatly where necessary). 12.5 mm thick

Providing and fixing Mineral fibre Acoustic Ceiling Tiles in 600mm x 600mm of 13 mm/ 15mm thickness to be placed in E-Grid Suspended ceiling Grid 2430 System consisting of Main Runner 3600mm long, Cross Tee 1200mm/ 600mm long and wall angle. The wall angle shall be fixed on PVC Dash fasteners on the perimeter of the wall by steel screw with distance 300 mm c/c. Main Runner shall be placed along the shorter dimension of the area to be covered. The distance between two Main Runners to be maintained at 1200 mm. The cross Tee 1200 mm will be inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to from a modular grid of 600mm x 600mm. E-Grid of module size 600mm x 600mm shall be supported by 4/6 mm dia G.I. wire from purlins/ soffit Mineral Fibre Aucoustic Ceiling Tiles of Everest Industries Limited should be placed in the E-Grid module to from a False Ceiling including the cuttings complete as directed. (A) Everest Designer Ceilings or equivelent as directed by the department (Primered) Using 15 mm thick ceiling tiles

Providing and fixing Aluminium Cell Ceiling of approved colour consisting of Main Runner, Cross Runner, Upper Sections, Lower Sections all of U-Shaped Profiles 10mm wide x 50mm deep x 0.5mm thick with inwardly returned edges of 2.5mm. Coil Coated on a Continuous Paint Line, Double baked and Roll formed from enamelled Corrosion Resistance Aluminium Alloy (Al. Mg) for higher strength and good Roll Forming characteristics. The Main Runner shall be fixed at a distance of 1.2mtrs c/c and shall be suspended by means of G.I. Suspension Rod 4mm diameter and a Galvanized Suspension Spring Clip at a distance of 1.2mtr c/c. The Cross-Runner shall be fixed to the Main Runner at a distance 0.6mtrs c/c., with a self-locking device. The Upper Section and Lower section shall be fixed to the Main Runner and Cross Runner in a form of a Cell Structure of module 150mm x 150mm with a self-locking device. Paint Finish: - Aluminium Main Runners Cross Runners Upper Section, Lower Section of U-Shaped Profiles shall be chromatised for maximum bond between metal and paint, enameled twice under high temperature one side with full primer and Finish Coat, the other side (inner side) with a Primer Coating and Skin Coat on a Continuos Paint Line. Modules Possible :- 150mm x 150mm

Providing and fixing of 4mm thick lacquer glass of approved color by architect/ Client with silicon on perfectly leveled water proof non-conventional plywood (preferably marine plywood) of minimum 12mm thickness mounted on the RCC wall/any other structure. The lacquered glass to be of 4mm thick highly durable, humid resistance, poly urethane lacquer glass. The Planilaque glass should be manufactured by industrial curtain coating process. It should meet quality standards as per BS EN 1036 1999 & confirms to PERSOZ hardness test of at least 220 oscillations. The substrate of the glass should conform to Standard BS EN 572 1995 parts 1 and 2: Glass in Building – Basic soda lime silicate glass products. Planilaque lacquered glass to be manufactured to right specifications, relating to consistency of color, opacity and homogeneity throughout production campaigns and also to the ageing properties, mechanical resistance, and resistance to humidity and to chemical agents of the lacquer. The color of the lacquer should remain stable when exposed to normal levels of ultra-violet light in interior applications

Fabricating, Providing and Fixing LAZER CUT SS SHEETcustomized perforated art panel (Jaali) made up of 3mm SS Sheet. Size 1220 x 2440mm customized to required size and shape as per drawing complete with all fixing, arrangement, & accessories.

Providing and fixing Wood Polymer composite (WPC) customized perforated art panel (Jaali) of Alstone or equivalent make comprising of 30mm thk. WPC panels with 550kg/m3 Density , size 1220 x 2440mm customized to required size and shape as per drawing complete with all fixing, arrangement, & accessories.

Providing and Fixing Wallpaper complete as per approved Shade and Pattern and as directed by the Engineer-in-Charge.

Providing wood work in frame (chowkhats) of doors, windows, clerestory windows and other similar works wrought, framed and fixed in position in contact with C.C. or brick masonry wall including supplying, fitting and fixing with M.S. hold fast (40mm x 3mm x 250mm) as per design embeded in cement concrete block in proportion 1:2:4 and with two coats of kiricide oiling to the timber faces in contact with C.C. and masonry as directed and specified. With sal wood Basement Floor

Gr. Floor

Extra for wood work for each subsequent floor above 1st floor level. Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

Providing and fixing 1st class timber moulded beading of size 25mm x 15mm around panel inserts of doors with countersunk wood screw including applying a coat of wood preservative on unexposed surface. With Teak wood/ Sissu wood

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood and with cross band and face veneered ply wood face panels conforming to relevent I.S. code including oxidised iron butt hinges (100 mm x 75mm x 3.5mm) 6 nos with necessary screws. Non decorative type and block board core. 35 mm thick.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Providing, fitting and fixing Wire Gauge shutters using galvd. M.S. wire of I.S. designation 85G with wire of dia 0.56 mm for doors, windows and clerestory windows including oxidised M.S. butt hinges (100mm x 58mm x 1.90mm). (A) With Teak wood / Sissu wood 35 mm thick.

Extra for providing lapping with 1st class teak wood battens 25 mm minimum depth on all edges of shutters.

Providing, fitting and fixing M.S. grill of required pattern for windows/ clerestory windows/ opening with M.S. Flats at required spacing in frame all round, square or round M.S. bars with round headed bolts and nuts or screws. I. Plain grill Fixed to wooden frames

Supplying, fitting and fixing anodised aluminium decorated grill with anodised aluminium rectangular frame of 'F' and 'H' section fitted with walls, columns or stiffeners by the department for all levels. (Aluminum Alloy procured from primary aluminium producer (On submission of certificate of alloy purchaging from primary producer).

Providing and fixing of tested fully glazed steel fire rated double leaf door with 120 minutes of integrity and radiation control (EW 120) fabricated with 1.6 mm thick galvanized steel sheet. The door frames are manufactured from 1.6 mm galvanized steel sheet pressed to form a profile of 35 mm x 60 mm on the vertical sides and 50 x 60 mm on the horizontal side. The door shutter would have a top rail and side rail 60 mm x 60 mm and a bottom rail of 110 mm x 60 mm. The sections have a special insulating infill. The overall door opening is 2440 mm x 2440 mm. The test is conducted in IFTS as per EN 1634-1: 1999. The glass should be Contraflam Door Lite, 11mm thick 120 min fire rated for both integrity & radiation control (EW 120 EI15) Non Wired, clear, Toughened, Interlayered glass with a light transmission of 86% and a sound reduction of 37 dB and manufactured in UL & TUV audited Facility and including UL-EU Certification. The glass should be compliant to class 2(B)2 category of Impact Resistance as per EN 12600. The glass should be held in its place with the help of 1.6 mm GI beading and a special ceramic tape with cross section of 5 x 20 mm as per the test evidence. The maximum glazing size should be not more than 1100 mm x 2200 mm (w x h) or 2.42 sq mt in total area which should be clearly mentioned in the test certificate. The shutters should be fixed to the frame using Dorma SS Ball Bearing Hinges of size 100 mm x 89 mm and 3 mm thickness or equivalent. Beading should be attached using 4 mm x 35 mm SS screws at a distance of 75 mm from the edges and 150 mm c/c henceforth. The door should be fitted with Dorma Mortise Sash lock 952F and door closer TS 73V of Dorma make or equivalent. The inactive leaf should be fixed to the frame using 600mm long Dorma tower bolt no 9114306 or equivalent. The test report will be considered valid only if it contains the stamp and signature of the authorized signatory from Saint-Gobain Glass India Ltd. Item to be complete in all respect including all assecceroies and hardwares.

Providing and fixing of Wooden fire rated doors as per BS:476 Part20 & 22 & IS 3614 part-1 & part-2 for stability, integrity and thermal insulation. 03 Criteria Wooden door confirming to IS 277 with the following specification. Recommended fire door shall have doors tested at CBRI for maximum rating of 2hrs tested either with or without vision panel. Individual Test certificates should be available for glass used in vision lites confirming the required fire ratings.Any deviation in specification other than what is mentioned in the test certificates are not allowed. Proper label confirming the type of door and the hourly rating is mandatory. Approved manufacturer Navair International Ltd or equivalent subject to architect’s approval. And should be ISO Certified company.Door leaf shall be minimum 52mm thick fully flush door with or without vision lite. 52mm thick shutter, comprising of 120mm x 70mm hardwood internal timber frame work, with infill of 48 kg/m3, ceramic fiber blankets, coated with VIPER FR intumuscent coating on both sides for insulation. Providing and fixing Non metallic 55mm (minium) thick asbestos free FIRE DOORS consisting of 120 minute fire rated 2nd class teak wood door frame of section 150mmX70 mm with heat activated inCumescent fire seal strip of size 15mm X 4mm and one coat of anti termite fire retardant primer and 120 minute fire rated Wooden Door Shutters conforming to BS:476 Part-22/IS; 3614 Part II for single & double leaf doors duly tested from CBRI / GQMC, Govt laboratory approved and made of 55mm thick asbestos free composite fire / smoke check wooden shutter of 120 minute fire rating comprising of two 10mm thick calcium silicate boards, 100% without asbestos, having density not more than 1150 kg/m3 and thermal conductivity 0.14 W/m*K sandwitching 25mm thick fire resistant insulation mineral wool filler coated with FR silicon sealant and faced with 3mm thick teak veneering on both side with heat activated intumescent fire seal strip of size 15mm X 4mm mounted on all the three sides of frame and polishing the shutters with Melamine polish over a coat of fire resistant primer including providing & fixing with with 4 nos. stainless steel Ball bearing hinges of size 100mmx76mmx3mm each shutter with screws to the door frames, a heavy duty door closure, Panic Bar device, Mortise Leaver Handle, Vision Panel of 300X300 mm with Fire rated 6mm thick clear Wired Glass for each door shutter complete. The rate includes the cost of all the materials, labor & T& P required for proper completion of the item described above except cost of Melamine polish which is to be paid separately. (For payment purpose the area of opening including door frame shall only be measured).

Providing, fitting and fixing battened, framed and braced door shutters including oxidised iron butt hinges (100mm x 58mm x 1.90mm) 6 nos. with necessary screws. With Teak wood / Sissu wood 40 mm thick.

Providing, fitting and fixing Full panelled door including oxidised iron butt hinges (100mm x 75mm x 3.55mm) with necessary screws (other fitting to be measured and paid saperately). With Teak wood / Sissu wood 40 mm thick.

Providing, fitting and fixing coloured anodised aluminium partition walls of standard section of approved brand (HINDALCO/ JINDAL/ BHAGWATI SAI with proof of purchase of ingot from primary producer)/ Other equivelent without joints metered and welded (manufactured to relevant IS specification) and providing and fixing angle cleat, rubber gasket, bolting device, screws etc. at all levels. Partly 6mm thick glass panes and 12mm prelaminated ply board. "Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including:" "(a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design." "(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places."

Design, Supply and Fixing Structural glazing system consisting of powder coated aluminium and Glass of approved make, aluminium frame work fabricated out of heavy duty aluminium extruded Profile powder coated with durable thermosetting polyester powder coating by electrostatic spraying and hard stoved to not less than 60 micron thickness to comply with BS 6496:1994 (1991) and AAMA 2603 -98 standard as per approved shade. All aluminium member and profile shale be of AC-25 grade as specification, the aluminium members shale be protected with protection tapes all around the profile for safety against external starches at site. (protection tape shale be removed anly at a time of handing over as per the instruction of project management.). The anchoring /bracing of the glazing to the RCC slabs /beams/colums salle be done with required number of non corrosive galvanized extended brackets of approved design (Galvanizing to be done conforming to IS:4759-1996 upto 610 gms per sqm, 80-90 microns thickness) with approved dash fasteners of The minimum 12mm dia and depth of minimum 100mm, in the concrete and stainless steel bolts including providing and fixing aluminium shims of various thickness to adjuct the beam level and Line variation. The anchoring system has been design to withstand the dead lode of structural wall As well as stresses due to wind pressure etc. the glazing frame shall be aligned for age vertical Mullion for the entire height and for each transom for the entire width horizontally by laser beam Equipment to ensure 100% x axis and y axis alignment. All the tight the Glazing frame work provided with approved in built ventilation and drainage system. All the joint of The structural glazing .system and the periphery, of glass shall be properly sealed with specified weather silicon. The details of inbuilt ventilation and drainage system should be submitted by the contractor before execution. EPDM gasket of suitable profile to accommodate glasses in all vision areas shall be provided at all glazing area to make the glazing water and air tight. Including the glass to be fixed at the outer side of the aluminium frame with structural silicon sealent (SG 18/ DC 995) and mechanical support with pressure plates and cover plates (the structural silicon bite size shall not be less than 8 mm/ as per the structural requirement / as per manufacturers recommendation). Expasion joint gap for mullion shall be minimum 15 to 20 mm to be provided where ever required, filled with expansion joint sealent from wacker, Dow corning DC 789/Sikka or euivelent. All screw, washers used shall be only stainless steel 316 grade and through, bolts, Nuts and Anchors used shall be only stainless steel of grade 316 etc. complete as per direction of EIC. (The structural design & drawing shall be provided by consultant/ approved specilized agency however the executing agency has to submit shop drawings and mock-up based on same which have to be approved by EIC before start of work.) 1) Mullions & Transoms, extruded aluminium sections shall be of 6063-T6 alloy to be as per structural calculations of Jindal/ Bhoruka or approved equivelent. 2) Coating of Aluminium section will be powder coated with durable thermosetting polyster powder coating by electrostatic spraying and hard stoved to not less than 60 micron thickness to comply with BS 6496-1994 (1991) and AAMA 2603-98 standard of approved shade as per direction of EIC. 3) Heavy duty, best quality EPDM gasket at joints and connection between Aluminium members. 4) All components shold be sealed for water proofing with silicon wacker, Dow corning of DC 789/Sikka or equivelent or water proof membranes with internal/ external aluminium flashing finished to approval. Curtain wall should be seal to hoist structure and allow movements etc. in its service life. Including supply, installation and fixing glass including cost of sealents, brackets, fasteners, screw, sleeve, spacer tape, backer rod, bolts, gasket, fixtures, scaffolding etc. complete in all respect. (The work is to be carried out by a specialized agency approved by the EIC.) a) 39.04 mm thick Hermetically-sealed laminated Insulated glass (double glazed) units of size and shape as required and specified, comprising with 13.52 mm thick laminated glass (6 mm Clear Heat Strengthened toughened clear Glass + 1.52 mm PVC Layer + 6 mm Heat Strengthened Low e Glass) + 12 mm air gap + 13.52 mm thick laminated glass (6 mm thick heat strengthened Toughened clear glass + 1.52 mm PVB Layer + 6 mm (Heat Strengthened Low e Glass, as per specification fixed in precise size on the outer infill panel. Note:- The aluminium extruded tubular and other aluminium sections to be paid saperately.

Providing, fitting and fixing anodised aluminium framed glazed doors with anodised aluminium frame made of 100mm x 45mm x 2.5mm section of approved brand HINDALCO/ JINDAL/ BHAGWATI SAI (with proof of purchase of ingot from primary producer)/ Other equivelent with door style of size 88mm x 45mm 2.5mm, top rails 50mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with glazing clip, special type rubber gasket complete etc. complete as specified and directed by the department at all levels. With 12 mm thick toughened glass

Applying one coat of cement primer of approve brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Providing two coats of Birla White Wall Care Putty (Water Resistance White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm). Thickness = 1.5 mm thick

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Narolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Narolac).

Painting two coats (Including priming coat) on new wood and wood based surface surface with enamel paint of approved brand and manufactures (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Narolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping. Surfaces over 100 mm in width or girth. High gloss (Asian paint/ Berger paint/ ICI paint/ J&N paint / Nerolec).

Painting two coats (Including priming coat) on new steel and metal surface surface with enamel paint of approved brand and manufactures (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Narolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter. Surfaces over 100 mm in width or girth. High gloss (Asian paint/ Berger paint/ ICI paint/ J&N paint / Nerolec).

Finishing new wall (two coats) with water proofing weather coat smooth anti-fungal exterior painting of approved make of Berger paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels.

Providing and applying textured wall coating in the branded name of SPECTRUM or equivelent with its all tools, plants and machineries and scaffolding etc. as per manufacturers guideline and specification of the product.

Polishing with french sprit polishing on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt, dust sand papered smooth and including a coat of wood filter.

Supplying, fitting, fixing brass fittings of approved make, rasonably smooth, free from sharp edges and corners, flaws and other defcts and with counter sunk holes for screw including necessary c.p. brass screw etc. complete. (bright natural matt. & satin finished). Mortice cylindrical type (Godrej make)- polished Brass

Curtain rod 25mm x 2mm

Door stopper with rubber stopper

Supplying, fitting, fixing Stainless Steel fittings of approved make, rasonably smooth, free from sharp edges and corners, flaws and other defcts and with counter sunk holes for screw including necessary c.p. brass screw etc. complete. (bright natural matt. & satin finished). Sliding door bolts 250x16 mm.

Tower bolts 300x10 mm.

Door Handles 150 mm.

Providing, fitting and fixing Door closer & Floor Spring of type Heavy duty good quality as directed & specified by the department. Godrej Heavy Duty Door Closer (Size 180mm x 65mm x 64mm)

Heavy Duty Floor Spring D100 (Size 308mm x 108mm x 40.5mm)

Supplying, fitting and fixing in position reinforcement bars confirming to relevant I.S. Code for R.C.C. work/ R.B. walling including straigtening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level.)From primary Producer: TATA/ SAIL/ Jindal Steel/ Shyam Steel/ RINL TMT Corrosion resistance steel (CRS) reinforecement bars Basement Floor

Gr. Floor

Extra over item for each subsequent floor or part thereof above first floor level. Mezzanine Floor-1

1st Floor

Mezzanine Floor-2

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor

9th Floor/ Terrace

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) (A) TMT bar made of Primary producer (From Primary producer)

Providing and fixing 1.25 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces

Providing and fixing stainless steel (Grade 304) railing made of hallow tubes, chanells, plates etc. including welding grinding buffing, polising and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i.e. fixing railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer in charge.(for payment purpose only weight of stainless steel members shall be considered excluding fixing assessories such as nuts, bolts, fasteners etc.)

Supply and installation of Kich/Q-Railing/Dorma Railing make AISI 316 Grade Stainless Steel Knock Down (No Welding) railing system comprising Ø 63mm Handrail containing high grade stainless steel bushing at every bend / jointing of railing to provide extra strength fixed by Cross-Bracket fixed on Ø 12x75mm S.S. Flat baluster (Design Code DT51-1-G13.52), with the help of M5 x 12mm handrail lamping screws. Baluster having 150x150x10mm thick specially investment casted base plat secured by Anchor Fasteners (Extra Strength SS Bolt of M10x80 Size & Anchor leeves of Brass M10 x 70mm) placed at maximum 1200mm c/c along with 6mm+1.52+6mm Toughened Laminated Glass (Height up to 772mm) at the side of baluster with fixtures. The balustrade would be fixed on Side of Steps with casted base plate. Base plate shall be concealed with suitable S.S. 316 grade cover Cap so that the mounting anchor fasteners are not visible after installation. Wall thickness of all Pipes shall be taken as 2mm along with all visible components developed in High Grade S.S. and whenever required, joints to be filled with bushings for extra strength. Railing height to be taken @ 915mm from floor level.

Providing plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) including finishing the surface with 10mm thick cement plaster in proportion 1:3 with a floating coat of neat cement finished.

Providing Drain with brick work in cement mortar in proportion 1:5 with half brick thick side and 100mm thick C.C. (1:3:6) base over one brick flat soling including 15 mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shuttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of the work etc. as specified. 300 mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

Supplying, mixing, laying and applying the following waterproofing systems over Raft slabs, Roof slabs, Terraces etc. including curing complete as specified and directed by the Department at all levels.: (i) 1mm thick single coat of Master Crete M-81 of Choksey Chemicals/ Dr. Sealkit Sealcrete (Asian Chemicals)/ RHEOMIX 131 of BASF mixed with cement in the ratio 1:2 as a prime coat. (ii) 3mm thick Polymer modified mortar-Cement sand mortar (in prop. 1:3) mixed with Master Crete M-81/ Dr. Sealkit Sealcrete (Asian Chemicals)/ RHEOMIX 131 of BASF @ 15% by weight of cement. (iii) 1mm thick coat of Master Crete M-81/ Dr. Sealkit Sealcrete (Asian Chemicals)/ RHEOMIX 131 of BASF mixed with cement in ratio 1:2 as final coat. (A) Using Master Crete M-81 of Choksey Chemicals/ Dr. Sealkit Sealcrete (Asian Chemicals).

Supplying, providing, mixing and laying over waterproofing layers/ coatings with concrete screed of average 30mm thick or as per drawings/ requirements in proportion 1:2:4 (1cement : 2fine aggregate : 4coarse aggregate) (by volume) with 10mm and down well graded aggregates and admixed with a normal plasticizer like Master Plast PL-1 of Choksey Chemicals /Dr. Sealkit Normal Plast (Asian Chemicals)/Rheomac 707 of BASF @ 0.3% by weight of cement and thereafter scoring the top surface of the concrete screed @ 200mm c/c as specified and directed by the Department.

Providing, supplying, mixing, laying 8mm thick cement Plastering in prop.1:6 over R.C.C. surfaces mixed with integral waterproofing compounds like Master Proof IWP-1 of Choksey Chemicals /Dr. Sealkit No.1 (Asian Chemicals) /Rheomac 707 of BASF@ 0.2% by weight of cement conforming to IS:2465 as specified and directed by the Department complete.

Providing, supplying, mixing and champhering the edges along joint of wall/ parapet wall and raft/ roof slab having champhered dimension of 150mm x 150mm with cement sand mortar (prop.1:4) mixed with Master Proof IWP-1 of Choksey Chemicals /Dr. Sealkit No. 1 of (Asian Chemicals)/ RHEOMAC 707 of BASF@ 0.2% by weight of cement over a primer coat on the area to be champhered with a combination of 100% acrylic Polymer Master Crete M-81/Dr. Sealkit Sealcrete (Asian Chemicals)/ RHEOMAC 115 of BASF of Choksey Chemicals and cement in the ratio 1:2 to be applied by brush as specified & directed by the Department complete.

Providing Grouting in R.C.C. walls & slabs by drilling holes @ 300mm c/c upto half of the wall depth in zigzag manner or as per drawings using a drill machine and fixing a nozzle of 20mm dia for injecting a grout/ grout slurry till the refusal of injected grout material fromadjacent nozzle (grouting operation pressure shall be in between 2 to 4 kg per sq. cm.). Followedby cutting the exposed nozzle so as to make the wall free from the grouting pipes and to seal the gap with polymer modified mortar as specified and direted by the Department complete at all levels. Grout slurry of cement, water and grout admixture Cebex 100 of Fosroc Chemicals/ Flowcable 50 of BASF/ Dr. Sealkit NSPG (Asian Chemicals) @ 225gms. Per bsg of cement.

Supply and installation of 1.2 mm thick MYK POWER PRUFE 800 below grade pre-applied integrally bonded waterproofing sheet membrane composed of 0.7 mm thick HDPE backing layer and a trafficable weather resistant protective granular layer realizing a firm bonding to poured concrete to prevent water ingress applied on prepared subbase and shoring prior to casting of concrete. The membrane is loosely-laid with the adhesive side facing upwards and removing the selvedge release film at the pre-manufactured overlap areas and are firmly pressed to ensure firm bonding. Seal roll end laps and non sleevage joints with a special tape strip powerpruf then firmly DST 100 a double side adhesive tape to stuck on the overlap removing granuels and pressing it thoroughly by roller to release entraped air if any. The product complies to a tensile strength of 800N, elongation of 400% and peeling strength from concrete 2.5N/mm.The rate is inclusive of all adhesives, sealants, tapes for overlap areas, labour and all jointing material with necessary tools and equipments for carrying out the work to the entire satisfaction of the Engineer-in-charge HORIZONTAL

Supply and installation of 1.5 mm thick MYK Self Stick 3000 post-applied Self adhesive Membrane with HDPE liner onto prepared and primed retaining wall surface with a side overlap of 75mm and end overlap of 100mm as per specification. All membrane to be terminated atleast 300mm above ground level by preparing a groove and terminate the membrane inside the groove and seal the groove with polymer modified mortar.Providing of MYK Waterbar RS 800 reswellable waterbar at all construction joints of lift pits, retaining wall & starter joints @ 80mm in from outer surface of RCC wall and to be fixed by adhesive ensuring atleast 30 mm overlap at end joints.Provide and fixing 25mm thick expanded polystyrene board as protection cover on MYK Self stick 300 at retaining wall by spot fixing with mastic VERTICAL SURFACE

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/ sqm).

PRODUCT-DR. FIXIT FLEXI PU 250(I)-LIQUID APPLIED POLYURETHANE WATERPROOFING MEMBRANE Compressed air cleaning has to be done so as to make the surface free of dust, debris, laitance etc. Repairing cracks by cutting and making V-groove in 25x25 mm, with SBR polymer modified mortar Dr. Fixit Pidicrete URP. filling the groove with CM(1:3) mixed with polymer 10% by weight of cement(cement, sand ,water will be supplied by the client Providing and making fillets at the junction of the walls and the slabs using cement mortar of 1:4 mix admixed with 5 % of DR. FIXIT URP by weight of cement. Provide and applying Dr. Fixit Flexi PU 250 , A single component PU based cold applied waterproofing coating based on pure elastomeric hydrophobic polyurethane resins having resistance to root penetration, Apply 2 [email protected]/sq.mtr.The product must have the following technical properties: Elongation at break > 800 % as per ASTM D-412, Tensile strength 4 N/mm2, Shore hardness-65 as per ASTM 2240.The coating must be applied over the prepared substrate primed with Dr. Fixit PU Primer. Providing & laying of minimum 150 gsm geotextile. Providing & laying of Protection screed admixed with intergral waterproofing compound- Dr.Fixit Pidiproof LW + to slope over geotextile as per recommendation FOR LANDSCAPE AREAS Laying of drainage board and geotextile before soil filling as per the manufacturer recommendations.

Preconstructional antitermite treatment as per the direction of the department complete. (Supplying of necessary tools and accessories by the contractor) with aqueous emulsion having concertration 1:19 with chloropirophose solution (tricel or equivelent) and water, i.e. 1% solution. At the bottom of foundation pits and wall on eighter side upto a height of 300mm from bottom of the excavation made for column plinth beam, wall, trenches etc. by applying emulsion @ 5 litres per sqm. Of the surface area before starting construction work.

In the back fill in immediate contact with the foundation structure after completion, column, wall etc. to a depth of 450mm and width 300 mm (when required refill in 200mm thick layers) applying the emulsion @ 5 litres per sqm. towards the concrete and masonry wall so as to ensure earth in contact with the structure well treated with chemical.

By applying in the entire levelled area after plinth filling and befor laying floor by applying the emulsion @ 5 litres per sqm. of the surface to be spread with light rodding so as to ensure proper absoption by the filled up earth.

By applying in the junction of walls column with the floor before laying floor and after operation of above making a channel 30mm x 300mm all over the walls and making rod holes @ 150mm apart upto ground below and applying emulsion @11 litres per sqm of vertical plinth wall surface inside the building so as to soak the soil with the emulsion upto the ground level and refill the holes and chanels with the original materials obtained in making channels.

By applying the soil along the external perimeter of the building (after construction completed) to a distance close to the plinth wall as specified and as directed by the deptt. Upto a depth of 300mm making rod holes along the line @150mm apart to a depth of 300mm and applying emulsion @4.5 litres per running meter ensure moistening of the soil with emulsion.

Add for plaster drip course in plastered surface or moulding to R.C.C. projections

Providing & fixing 16 mm thick multiwall polycarbonate sheet of bayre lexn or equivelent reuired shed fixing with aluminium profile of required width (alcox system) to M.S. tubelar trusses with drilling/ traping /screw and EPDM GASKET with ceiling of all joint by silicon sealant all complete as per direction of engineer-incharge. the surface area shall be measured for payment.

Providing and fixing of Expanded Metal Mesh Panels on Facade Area. The vertical edges of each mesh panel shall be welded to continuous vertical aluminium 'L' angle profiles measuring 25mm x 25mm at approx. 250mm intervals. The angle profiles together with the mesh already welded, shall then screwed from the front to vertical aluminium T / Box sections using 5.5 x 25mm self-drilling / self-tapping SS screws (AISI 304 grade) at max 400mm intervals vertically. The vertical T/Box sections shall be fixed to the MS framework using aluminium/mild steel L-brackets and stainless steel anchor faseners / screws as applicable, spaced at maximum 1800mm c/c vertically (actual spacing to be based on a structural/ static calculation). The brackets shall be fixed to the vertical aluminium T profiles using two stainless-steel self-tapping / Self-drilling screws of dimensions 5.5 x 25mm (AISI 304 grade). Design : RB 85 Strand width : 11mm LWP - 100mm SWP – 35mmThickness-2mm Supply of Expanded Metal Mesh Pannels

Installation of Expanded Metal Mesh with frame work

Providing and applying textured wall coating in the branded name of SPECTRUM or equivelent with its all tools, plants and machineries and scaffolding etc. as per manufacturers guideline and specification of the product.

Powder coated aluminium louvers / screen system with 3 mm thick substructure and 2 mm thick top layer . Item shall includes Designing, Supplying, installation and fixing of profiled louvers including stainless steel screws / fasteners, flashings as required. Top Layer shall consist of 2 mm thick Powder coated aluminium 50 X 75 mm box section up to 2500 mm long of approved shade and color. The fins should be fixed to Substructure using SS Screws . The substructure shall consist of 50 mm X 100 mm x 3 mm thick Aluminium Box section installed at a spacing of aprox 1200 mm centre to centre on the pressure plates with suitable brackets / fasnteres. Aluminum Interlocking member shall be fixed over the alumnium box section substructure using stainless screws. Size of Substructure sections may vary on final details and wind prssure calculations. All fasteners shall be of stainless steel 316 grade in order to prevent corrosion / galvanic action with the components fastened.

Providing and fixing machine cut, mirror/ eggshell polished , 20 MM THICK Granite stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge.

Providing and fixing Toilet Cubicle (of following standard dimension which includes 600 mm door size width) made of heat, bacteria, water, chemical, scratch, impact and anti bacterial resistant 18 mm thick solid compact laminate panels Finish of the compact laminate should be raw silk which include doors, pilasters and intermediate panels finished with approved texture/shade as per the detail drawing and as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard. This also includes providing and fixing in position necessary hardware made out of Stainless Steel (Grade 316) as per manufacturer's specifications and EIC instructions like (1) Door Knob, (2) Gravity Hinges, (3) Thumb turn lockset indicators, (4) Coat hooks, (5) U- Channels, (6) SS-Shoe Box Plate, (7) MS-Base Plate, (8) Rubber noise deafening tape, (9) Screws and wall Plugs.

Providing and fixing vanity counters with 12 mm thick ISO certified Acrylic solid surface of approved make of approved shade in approve design, with properties like anti-bacterial antifungal, heavy duty scratch resistant & stain resistant, impact resistant, insulative & non conductive, Green Guard certified, Fire rating as per standard EN 135 -1-lb surface spread of flame and having minimum Specific Gravity 1.65 g/cm3 properties. DuPont Corian© sheets or equivalent will be cut, pasted, thermoformed, engraved, inlayed and finished to give the desired shape and finish as per the drawings and design provided by the architects. The finished vanity module will be installed on site on a 2' x 2' framework made of a 2"x 2" Aluminum Box Sections of 4-5 mm thickness. Back splash and front fascia of desired width needs to be provided along on the washroom vanity. All seams in to be filled with DuPont Corian Adhesive or equivalent of matching color and finished to have a inconspicuous seams to give a monolithic appearance. Use Good Quality Silicon Sealant (Dow Corning or equivalent) for Pasting of Corian or equivalent to the Metal Frame provided for Support and for filling invisible undesired gaps happening complete in all respect as directed by Engineer-in-charge.

Designing, Providing and Fixing of Treated Bamboo Structure made using bambusa balcooa or equivalent with minimum thickness of 10 mm Size 80 mm (+/- 10 mm) diameter treated with preservative inside the bamboo pole & dosing with CCB (Chromium Copper Bromate) using Pressure through Vacuum treatment plant with retention level 6 kgs per Cum in accordance with IS 9096. (Group -A bamboo pole) bambusa balcooa 3 to 4 year age of culm with minium wall thickness of 10 mm & distinctive inter-nodes 450 mm max. These bamboos are used for making bamboo facde including bending of bamboo, installation on metal ring as per design using SS Grade 304 studs / bolts, nuts and washers. All exposed nuts will be overed with bamboo cap. All exposed bamboo surface will be polished with Polyurethane coatiing of MRF brand with first coat with sealer and second coat of matt finish final coat.

Supply of approved make of structural steel plate fabricated section/rolled , testing, cutting, fabrication, welding to the required Profile, shape and size as per apprved shop drwaings for Structural Steel Column / Steel Beams / Bracing Works & Staircase Works etc complete made of Grade E450 conforming to IS 2062 - 2006, IS: 4923 - 1997, IS: 1239 - 2004 and IS: 1611 - 1960 including shop fastening members with a coat of anti rust primer after cleaning/shot blasting ( whereeverrequired). The work shall be carried out strictly in accordance to structural consultants drawing and specification and directions. The structural steel shall conform to IS : 226 / 2062 - and shall be of TATA / SAIL / JSW / JSPL make.

Providing and fixing 40mm thick cladding comprising of Wooden framework using 25mx50mm sections at a maximum spacing of 600mm in any one direction (including adding members as required) covered with12mm thick BWP ply layered with 4mm thk. veneer (Basic Rate Rs.100/-sqft)on one side pasted and pressed with adhesive to give a uniform and smooth finish, including 4mm thk. S.S. strip framework on all sides of veneer panels with wooden member surround, top moldings / margins, melamine polish etc. to finish the thickness, as shown complete in drawing. All members / ply etc. shall be treated with anti-termite solution as per norms. No extra shall be paid for making of openings, door / window frames and for making provisions for electric conduits.

Providing and fixing Wood Polymer composite (WPC) customized perforated art panel (Jaali) of Alstone or equivalent make comprising of 30mm thk. WPC panels with 550kg/m3 Density , size 1220 x 2440mm customized to required size and shape as per drawing complete with all fixing, arrangement, & accessories.

Providing and fixing of 4mm thick lacquer glass of approved color by architect/ Client with silicon on perfectly leveled water proof non-conventional plywood (preferably marine plywood) of minimum 12mm thickness mounted on the RCC wall/any other structure. The lacquered glass to be of 4mm thick highly durable, humid resistance, poly urethane lacquer glass. The Planilaque glass should be manufactured by industrial curtain coating process. It should meet quality standards as per BS EN 1036 1999 & confirms to PERSOZ hardness test of at least 220 oscillations. The substrate of the glass should conform to Standard BS EN 572 1995 parts 1 and 2: Glass in Building – Basic soda lime silicate glass products. Planilaque lacquered glass to be manufactured to right specifications, relating to consistency of color, opacity and homogeneity throughout production campaigns and also to the ageing properties, mechanical resistance, and resistance to humidity and to chemical agents of the lacquer. The color of the lacquer should remain stable when exposed to normal levels of ultra-violet light in interior applications

Demolishing lime concrete without damaging the structure and disposal of debris as directed at all levels

Demolishing plain cement concrete including disposal of debris as directed for all levels Prop (1 : 4 : 8) or leaner mix

Demolishing plain cement concrete including disposal of debris as directed for all levels Prop (1 : 3 : 6) or reacher mix

Demolishing RCC work including stacking of steel bars and disposal of unserviceable material as directed for all levels

Demolishing RB work including stacking of steel bars and disposal of unserviceable material as directed for all levels

Extra for cutting reinforcement in RCC or RB work at all levels (Payment to be made on cross sectional area of RCC or RB work obtained by multiplying the length of the cut reinforcement and thickness of the member).

Extra for scraping, cleaning and straightening reinforcement from RCC or RB work at all levels

Demolishing brickwork including stacking of serviceable materials and disposal of unserviceable materials as directed for all levels

Demolishing stone rubble masonry including stacking of serviceable materials and disposal of unserviceable materials as directed for all levels

Dismantling wood work in frames, trusses, purlins and rafters including stacking the materials as directed by the department for all levels.

Dismantling steel work in single sections (R.S.Joists, channels, angles, tees and flats etc.) including dismembering and stacking the materials as directed by the Department for all levels.

Dismantling steel work in built up sections in joists, angles, channels, tees, flats etc. including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking the materials as directed by the Department for all levels

Dismantling all types of corrugated/ trapezoidal sheet roofing including ridges, hips, valleys and gutters etc. and stacking the materials as directed by the department for all levels

Demolishing CC floors of various thickness including top layer and base course and disposal of debris as directed for all levels.

Demolishing mosaic floor of various thickness, both mosiac tiles and cast-in-situ type including CC base course and removal of debris as directed for all levels.

Demolishing R.C.C./ P.C.C. pile head of different diameters carefully without disturbing the remaining portion of the pile including opening out of the pile head to be demolished by excavating the earth upto required depth and clearing the debris as directed.

Dismantling all types of ceiling, partition and wall lining and stacking the materials as directed by the department for all levels

P/F STRETCHED FABRIC ACOUSTIC PANELS using: • GI frame work of 48mm GI Studs, 50 mm foor using 0.55mm thick and stud channels at 610mm x 610mm, 0.5mm thick, fixed with MS angle cleats 1220x610mm centers to wall by using metal fasteners, backed with 22 SWG x 12.5mm GI Chicken Wire Mesh with air gap a minimum of 50mm on back side, as per detailed drawing. • The frame work to be filled with glass wool of 50mm thick of 48 kg/Cum Cu. (Owens Corning) laminated with Black FRP Tissue on the outer side, and chicken wire mesh support on the rear side abuting the wall face. The entire glass wool surface to be covered with 12mm thick FR ply, with 8mm diameter drilled perforations at 25mm c/c in both directions. Finished in stretched fabric finish, using UPVC grippers (Waltract/ Cineview ) fixed to 50mm x 12.5mm commercial plywood runners. The fabric should be inherintly fire-retardancy.

SANITARY WORKS Sanitary Fixtures & CP Brass Fittings Provinding fitting and fixing Vitreous china wall hang water closet (European type W.C PAN 400 mm high) with seat and lead, CP Brass hinges and rubber buffers , CI/MS brackets,40 mm dia flush band with fittings including painting of fittings and brackets, required.(flushing Cistern to be paid separately) Jaquar Make White Florentine Cat. No. FLS-WHT-0111 (inclusive of seat cover and fittings)

Solo Cat. No. SLS-WHT-0117 (inclusive of seat cover and fittings)

Supplying ,fitting and fixing concealed cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) Jaquar make Concealed Cistern (Cat. No. CIB-WHT-31801011X) with Control Plate (CP) (Cat.No. CIS-CHR-31191510X)

Providing fitting and fixing vitreous china flat back type lipped front urinal; basin of with automatic flushing cistern with standard flush pipe and CP brass spreader andbrass unions,etc. complete including painting of fittings and complete, cutting and making good the walls & brackets, cutting and making good the walls & floors wherever required. Jaquar make White Urinal (Cat.No. URS-WHT-0704) with Sensor (Cat. No. SNR-CHR-51097)

Suppling fiting and fixing glass division plate of jaquar make including fitting and fixing compate as directed and specified.

Provinding vitreous china wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required.(Pillar cock, stop cocks, waste coupling are to be paid separately ) Table Top Basin Jaquar Make Solo ( Cat. No. SLS- WHT-0558)

Lyric ( Cat. No. LYL-WHT-0555)

Providing fitting & fixing stainless steel kitchen sink of parry make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings, cutting & making good the walls wherever required.( Sink cock, stop cocks, waste coupling are to be paid separately . Parryware Make Single Bowl with Drain board (400x200) flat Edge - Glossy ( Cat. No. C8537)

Providing fitting and fixing Decorative Mirror complete as directed and specified. Parryware Make Size 800mmx600mm

Size 600mmx 450mm

Providing,fitting and fixing CP soap tray / soap dish complete as directed and specified. Jaquar make Hotelier (Cat.No. AHS - 1531)

Providing fitting and fixing liquid soap dispenser and liquid soap container complete as directed ad specified. Jaquar make Kubix with glass bottle (Cat.No. AKB-35735)

Providing fitting and fixing CP towel rail complete as direted and specified Jaquar make Kubix(600mm long) (Cat.No. AKB-35711)

Providing ,fitting and fixing chrome plated robe hook complete as direted and specified. Jaquar make Kubix (Cat.No.AKB-35791)

Providing, fitting and fixing chrome plated tumbler holder complete as directed and specified. Jaquar make Kubix (Cat.No.AKB-35741)

Providing fitting and fixing chrome plated TOILET PAPER holder of complete as directed and specified. Jaquar make Continetal toilet paper holder with flap(cat.No. ACN1153N)

Kubix toilet roll holder with cover (Cat.No. AKB-35753)

Providing ,fitting andd Fixing chrome plated waste coupling complete as directed and specified. Jaquar make 32mm (HT/FT) (Cat.No. ALD-705/709

Providing ,fitting andd Fixing chrome plated Bottle Trap complete as directed and specified. Jaquar make Bottle trap (with internal partition) 32mm size with 250mm long wall connection pipe(Cat.No.ALD-769)

Supplying fitting and fixing C.P bib cock 15 mm dia of approved brand as directed and specified (G.I & C.P pipes will be measured separately) Jaquar make, Continental / clarion Bibcock long thread

2-Way bib cock

Supplying fitting and fixing chorom plated (C.P) stop- cock of approved brand and size as mentioned below as directed and specified.(G.I) & C.P Pipes will be measured and paid separately) Jaquar , Continental / Clarion 15mm (Angular stop cock with long thread )

Supplying and fiiting fixing C.P pillar cock of 15 mm dia of approved brand as specified and directed. Jaquar make Continental

Supplying,fitting and fixing chorme plated (C.P) shower 15 mm dia. Of approved nrand as directed and specified.( pipes will be measured and paid separately) Jaquar Make Continental Shower arm 190mm long heavy casted body with wall flange

Pressure adjustable shower with revolving joint

Supplying, fitting and fixing Chorme plated (C.P) basin mixer complete as directed Jaquar make (For VIP use. Prior approval of chief Enginner PWD (Bidg) must be taken before use) Continental/ Clarion Central hole basin mixer without popup waste system with 450mm long coper pipe and brass nuts Cat.No. 169

Supplying, fitting and fixing Chrome Plated (C.P) sink mixer complete as directed. Jaquar make Continental / Clarion Sink mixer with swinging casted spout ( wall mounted model) Cat No. 309

Supplying fitting and fixing Chrome plated (C.P) bath tub spout of approved brand complete as directed. Jaquar make, Continental Bath tub spout 235 mm long with wall falnge Cat No. 433

Supplying , fitting and fixing Chorme Plated (C.P) divertor of approved brand complete as directed . Jaquar make Continental/ Clarion - 4 way divertor for concealed fitting with build in non return valves with divertor handle Cat. No.421

Providing and fixing Health Faucet with 1 m long flexible tube and wall hook including all fittings Jaquar Cat No.ALD-CHR-593N or approved equivalent.

Providing and fixing Stainless Steel Grab Bar including all fittings complete.(Euronics Cat. No.-EGR-01 600 mm) or approved equivalent

Providing and fixing Stainless Steel Swing Handicap Grab Bar Euronics Model No.EGR S-02 or approved equivalent,Including cutting and making good the walls wherever required

Providing and fixing fully automatic Hand dryer including all fittings complete.(Euronics Model-EH 26 NW )

Providing and fixing 150 litre/ hr. cooling and storage capacity,fully stainless steel electric storage type water cooler ( Blue Star model No. SDLX 15150 or equvalant) with inlet hose connection inbuilt float valve. 2 Nos. outlet foucet, drain tray with waste and pipe up to fllor trap heavy compressor and wire up to socket, 3 pin plug etc complete in all respect.

Soil, Waste, Vent & Rain Water Pipes Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. In Exposed Surface or in Trenches. 160mm dia.

110mm dia

75mm dia

63mm dia

50mm dia

Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 160mm dia.

110mm dia

75mm dia

63mm dia

50mm dia

Supplying fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches. 160mm dia.

110mm dia

75mm dia

50mm dia

Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 160mm dia.

110mm dia

75mm dia

50mm dia

Supplying fitting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified. In Exposed Surface or in Trenches. 110mm dia

Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 110mm dia

Supplying fitting and fixing 45 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches. 160mm dia.

110mm dia

75mm dia

50mm dia

Supplying fitting and fixing PVC plain single tee of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches. 160mm dia.

110mm dia

50mm dia

Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 160mm dia.

110mm dia

50mm dia

Supplying fitting and fixing PVC plain single tee with door of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. In Exposed Surface or in Trenches. 110mm dia

Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 110mm dia

Supplying fitting and fixing PVC plain single Y of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches. 160mm dia.

110mm dia

Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 160mm dia.

110mm dia

Supplying fitting and fixing PVC plain single Y with door of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches. 110mm dia

Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 110mm dia

Supplying fitting and fixing PVC coupler of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches. 110mm dia

75mm dia

Supplying fitting and fixing PVC reducing Tee of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches. 160mmx110mm

110mmx75mm

Supplying fiting and fixing PVC reducing Tee with door of (Supreme/Prince) or other ISI approved including joinning, fitting and fixing etc. in exposed surface or trenches as necessry complete at all levels including below G.L as directed and specified. 160mmx110mm

Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approved including joinning, fitting and fixing etc. in exposed surface or trenches as necessry complete at all levels including below G.L as directed and specified 110mm

Supplying fiting and fixing PVC cleaning pipe of (Supreme/Prince) or other ISI approved including joinning, fitting and fixing etc. in exposed surface or trenches as necessry complete at all levels including below G.L as directed and specified 160mm

Providing fitting and fixing PVC of cowel of ISI make complete as directed and specified . 110mm dia . PVC cowel of ISI make

75mm dia . PVC cowel of ISI make

Providing fiting & fixing C.P. Grating complete as directed and specified. 160mm

Providing and fixing uPVC P-Trap including setting with cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 hand stone ballast 20 MM nominal size) the inlet from floor level to trap rim to be grouted and cemented neat manner including cutting and making good the floor & wall wherever requiredcomplete in all respects 110 mm inlet and 110 mm outlet.

Providing and fixing cast brass clean out plug with suitable insert keys for opening, male threaded joint with PP/ uPVC female threaded socket caulked to PP/ uPVC pipe including cost of Solvent cement or Other Joint. 100 mm dia

150 mm dia

Providing and fixing in position 110x63 mm OD uPVC reducing elbow including fix to floor with cement mortar.

Providing and fixing 110 mm OD uPVC inlet fitting/ Extension Piece with 2 or 3 inlets of 40 to 63 mm OD, fixed to uPVC trap with solvent cement joint and set in cement concrete as per drawing complete.

Water Supply System Providing and fixing Polythene-Aluminium-Polythene (PE-AL-PE) composite pressure pipes UV stabilised with corbon black conforming to ASTM F-1282-1995 for water supply including clamps at 1.0 metre spacing, cutting & making good the walls etc. Kitec Brand Exposed on Wall 1620 (20 mm OD) Pipe

2025 (25 mm OD) Pipe

2532 (32 mm OD) Pipe

3240 (40 mm OD) Pipe

4050 (50 mm OD) Pipe

Concealed pipe with cutting chase & making good the walls 1620 (20 mm OD) Pipe

2025 (25 mm OD) Pipe

2532 (32 mm OD) Pipe

3240 (40 mm OD) Pipe

4050 (50 mm OD) Pipe

Suppling fitting and fixing G.I pipes of following sizes, with all necessary 'R' brand or similar approved G.I. fittings such as bend,tee,elbow, reducer,nipple,plug,long screw fitting,H.W. clamps etc. complete at all levels including below G.L as directed and specified. Exposed on Walls Using Tata make 50 mm dia (medium)

40 mm dia (Medium)

32 mm dia (Medium)

25 mm dia (Medium)

20 mm dia (Medium )

Supplying fitting and fixing pipes with all necessary fitings in exposed ot in treches including trenching and refilling the same etc complete as directed. G.I pipe with GI fitting TATA / SAIL (Medium) 80mm diameter

100 mm diameter

CPVC pipe with CPVC fitting (Using SUPREME/ PRINCE /SFMC/ FUSION brand pipe) 25mm(OD) diameter

32mm (OD)diameter

50 mm (OD)diameter

75mm(OD) diameter

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 20 mm dia nominal bore

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

65 mm dia. nominal bore

80 mm dia. nominal bore

100 mm dia. nominal bore

Painting G.I. pipes and fittings with two coats of anticorrosive bitumastic paint of approved quality. 80 mm dia. nominal bore

100 mm dia. nominal bore

Providing and filling sand of Grading Zone-V or Coarser Grade,alround the GI pipes in External Work. 25 mm dia nominal bore

32 mm dia nominal bore

50 mm dia nominal bore

80 mm dia. nominal bore

100 mm dia. nominal bore

Providing and fixing forged brass ball valve of brass body with hard chrome plated steel ball inside PTFE (Teflon) seat & ring with chrome plated centre handle with female BSP threads complete in all respects. 20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Providing & fixing butterfly valve tested to a pressure not less than 16 Kg/Sq.cm. Including rubber gasket, 2 nos. Table-E flanges, nuts, bolts, washers & painting complete as required. 65 mm dia

80 mm dia

100 mm dia

Providing and fixing Thermoflex or Kaiflex thermal insulation tubing a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of following nominal bores and thickness including all required accessories complete as per specification. 6 mm thick (Concealed Pipes) For 20 mm dia Pipe

For 25 mm dia Pipe

For 32 mm dia Pipe

For 40 mm dia Pipe

Providing and fixing Thermoflex or Kaiflex thermal insulation tubing, a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of following nominal bores and thickness including protection by wrapping with 24 gauge alumminium sheet with riveted screw joints all required accessories complete as per specification. 13 mm thick (Exposed Pipes) For 20 mm dia Pipe

For 25 mm dia Pipe

For 32 mm dia Pipe

For 40 mm dia Pipe

For 50 mm dia Pipe

Providing and fixing forged brass single acting air release valve with screwed inlet 25 mm dia.

Providing, laying and Jointing G.I. "B class" pipes and fittings conforming to IS: 1239 (Medium class) with fittings, union and clamps including cutting holes in wall, makes chases in wall and making good the same in cement mortar 1:2 (1cement : 2 coarse sand) complete in all respects for internal works including pipe supports with galvanised GI. slotted angle iron, GI clamps, spacers as required and making good wherever required. (For Vertical in Shafts & Terrace only) Internal Work - Exposed on Wall 65 mm dia. nominal bore

80 mm dia. nominal bore

100 mm dia. nominal bore

Supply, Installation, Testing & Commissioning of 3000 LPD Flat Plate based on thermo syphon solar water heating System suitable on greavity feed water including internal system piping, insulated hot water storage tank with heat exchanger, valves on inlet & outlet, Y strainer temperature gauge, MS Angle frame etc. Details of each items used in one 3000 LPD system are mentioned below. Solar Water Heating System 24 Nos. Solar Flat Plate collector having collector area should be min. 2 Sq, Mtr. (Collectror should be BIS & MNRE approved. One No. Horizontal/Vertical hot water mixing tank of 2000 ltr capacty shall be made out by 1.6 mm thick stainless steel 316 grade sheet ,100 mm thick rock wool/glass wool slab insulation (density of glass wool 64 Kg/Sqm.) covered with chicken mesh & 22 SWG aluminum sheet cladding outside the tank. Tank shall be provided with flanges for inlet outlet, over flow/ drain connection & Vent pipe with M H cover of 450 mm internal dia., Temperature and pressure release valve should be on top of water storage tank 1 Lot of Inter-connected CPVC system piping of required size with fittings, insulated with 50 mm glasswool/rockwool insulation covered with chicken mesh & 26 SWG aluminum cladding to connect the collectors with hot water storage tank. Providing and fixing a lot of Temperature Gauge, vent pipe, ball valve , NRV, CI/brass Y strainer, PT - 100 sensors with thermocople wire ,MS. Angle stand for hot water tank . One No. Heat Exchanger cage type inbuild the hot water storage tank of SS 316 having surface area not less than 2.4 Sq. Mtr. One No. Control Panel for recirculation pump having DTC with contractor, MCBs, and cycling timer for pump. Three Nos. Electric heater of 9 KW. With Thermostatic control. Solar System as Described Above

Supply, installation, testing & commissioning of vertical inline hot water reciculation pumping set ( set of 2 pumps 1 Working + 1 Stand by) of 60 LPM Capacity at 15 Head with Stainless steel body, impeller, casing, shaft and C.I. base & head with mechanical seal, connected to a TEFC induction motor suitable for 415+/- 10% volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with control valves, power & control cables, suction/ delivery headers,vibration eliminating pads under foundations,vibration eliminators, 80x40 mm I section base plate bolted to cement concrete foundations complete.Vendor to submit performance curves and technical catalogue of the proposed model for review and information.

Sewerage System/Storm Water Drainage System Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed, within a lead of 50m. All kinds of soil Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia.

Pipes, cables etc, exceeding 300 mm dia but not exceeding 600 mm dia

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5m, but not exceeding 3m. (Rate is over corresponding basic item for depth upto 1.5 metre). Pipes, cables etc, exceeding 80mm dia but not exceeding 300mm dia

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Extra for every additional lift of 1.5m or part thereof in: All kinds of soil (Manhole)

Providing, laying and jointing glazed stoneware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. 250 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size) all round S.W. pipes including bed concrete as per standard design. 250 mm diameter

Constructing brick masonary circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1 :3:6 mix (1 cement : 3 coarse sand : 6 graded 40mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design: 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560mm internal diameter confirming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With Sewer bricks conforming IS : 4885

Extra depth for circular type manhole 0.91m internal dia (at bottom) with beyond 0.91m to 1.67m. With Sewer bricks conforming IS : 4885

Constructing brick masonry circular manhole 1.22m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With Sewer bricks conforming IS : 4885

Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond 1.68 m to 2.29 m : With Sewer bricks conforming IS : 4885

Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 2.30 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With Sewer bricks conforming IS : 4885

Extra depth for circular type manhole 1.52 m internal dia (at bottom) beyond 2.30 m : With Sewer bricks conforming IS : 4885

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 250 to 300 mm diameter

Supply of Grease separator ECO-JET-OD NS 04 with sludge trap capacity 400 Ltrs. according to DIN EN 1825, for free standing installation, of polyethylene, material LLD-PE, with grease storage capacity 200 liters, total wastewater capacity 830 liters, with direct suction, with connecting flange DN 65 PN 10 For local suction line R 2 1/2”, with fire hose quick coupling B with 2 odour proof maintenance openings DN 350 inlet and outlet DN 100. With max dimensions: 770x2000x1680mm With Inspection Windows & Filling Device.(Make : ACO Part No. 3554.64.41 or Equivalent)

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5m, but not exceeding 3m. (Rate is over corresponding basic item for depth upto 1.5 metre). Pipes, cables etc, exceeding 80mm dia but not exceeding 300mm dia

Pipes, cables etc, exceeding 300 mm dia but not exceeding 600 mm dia

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size) up to haunches of S.W/RCC pipes including bed concrete as per standard design. 250 mm diameter

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe

450 mm dia. R.C.C. pipe

600 mm dia. R.C.C. pipe

700 mm dia. R.C.C. pipe

800 mm dia. R.C.C. pipe

Constructing brick masonary circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1 :3:6 mix (1 cement : 3 coarse sand : 6 graded 40mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design: 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560mm internal diameter confirming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 0.91m internal dia (at bottom) with beyond 0.91m to 1.67m. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular manhole 1.22m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond 1.68 m to 2.29 m : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond 1.68 m to 2.29 m : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth beyond 45 cm of brick masonry chamber For 455x610 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Rain Water Harvesting System Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including geting out and disposal of excavated earth, lead upto 50m and lift upto 1.5m, as directed by Engineer-in-Charge. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Extra for every additional lift of 1.5 m or part thereof in. All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves,chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing & reinforcement with1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size)

Centring and shuttering including stutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and acees platform

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars of Grade Fe-500D or More.

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12mm dia steel bar conforming to IS :1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263mm and width as 165mm with minimum 112mm space between protruded legs having 2mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and heaving manufactures permanent identification mark to be visible even after fixing " including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6: (1 cement :3 coarse sand :6 graded stone aggregate 20mm nominal size )complete as per design.

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. HD-20 circular shape 560 mm internal diameter.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer –in-charge, upto 90 metre depth below ground level. All types of soil 400 mm dia.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer –in-charge. 200 mm nominal size dia.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia.

Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & levelling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer –in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm Clamp.

Tube Wells ( 2 Nos.) Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 ( 1cement : 2 Coarse sand : 4 graded stone aggregate 20 mm nominal size )

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer –in-charge, upto 90 metre depth below ground level. All types of soil 400 mm dia

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer –in-charge, beyond 90 metre & upto 150 metre depth below ground level. All types of soil 400 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer –in-charge. 200 mm nominal size dia.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia

Providing and fixing 80 mm dia. GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete.

Supply, Lowering, installation & testing of KSB make submersible pumping set with 7.5 HP motor 4 stage pump suitable for 20/26/30/38/40/45/50 m3 hr. at 42/38/36/32/29/25/20 mtr. Head respectively. With Three Phase. (Model: 273/4)

Providing & fixing cable 6 sq.mm. From submersible pump to panel board.

Providing & fixing Panel Board for submersible pump fitted with DOL starter ammeter, voltmeter single phase preventer standard/indo/cop make MCB of off switch push bottom duly wired and made out of 16/18 SWG sheet.

Providing & fixing butterfly valve tested to a pressure not less than 10 Kg/Sq.cm. Including rubber gasket, 2 nos. Table-E flanges, nuts, bolts, washers & painting complete as required. 80mm dia

Providing & fixing dual plate CI wafer type check valve tested to a pressure of 10 Kg/sqcm. Including rubber gasket, 2 nos. table-E flanges, union, nuts, bolts, washers & painting complete as required. 80mm dia Sewage Treatment Plant 170 KLD ( SBR Technology ) Note : All Civil Works with Structural Walk Ways/ Railings, General Lighting and Ventilation to be Done by Client/Owner. Design, Supplying, Installing, Testing & Commissioning of Sewage Treatment Plant capacity 170 KLD (excluding excavation, back filling & disposal of surplus earth /Civil construction work) for the following duty: Nature of effluent - Domestic Sewage from Toilet use , kitchen waste and other areas of residentail buildings. Incoming parameters: pH - 6 - 8.5 BOD5 - upto 250-350 Mg/L S. Solids - 250 - 400 Mg/L COD - upto 450-600 Mg/L Oil & Grease - 50-100 Mg / L Final effluent discharge standard after treatment pH - 6.0 - 8 BOD5 - Less than 10 Mg/L S. Solids - Less than 30 Mg/L COD - Less than 80 Mg/L Oil & Grease - Less than 10 Mg/L E Coli - Nil All piping, valves & level indicator/ controller etc. within plant room.

Supply, installation, testing & commissioning of 2 Nos Manual Stainless Steel Bar Screen with suitable lifting arrangement for required sizes (size 800 mm wide x 900 mm high approx.

Supply, installation, testing & commissioning of electronic type level indicator and controller for automatic operation of the system with high/low level alarm complete with auxillary NO/NC contacts.

Supply, installation, testing & commissioning of non clog open impeller type pumps, having CI casing & CI impeller complete with all accessories, motor of required capacity. Delivery header with isolation valve and NRV, liftng arrangement, pressure gauge on delivery line with isolation cock level controller with wiring to control the level of sump automatically. Pump shall have following duty for reference and vendor to confirm on design base. Submersible Sewage Transfer Pumps 2 Nos. ( 1 Working + 1 Standby ) (Solid Handling Cap. 35 mm) Flow rate (each) = 45 M3 / Hr Head = 10 Mtr

Sludge Transfer Pumps 2 Nos (1 Working + 1 Standby) (Solid handling cap. 8.5 mm) Flow rate (each) = 5 M3 / hr Head = 12 Mtr

Supply, installation, testing & commissioning of Twin type rotary air blowers (1 W + 1 S) Capable of delivering 300 cum/hr (each) of free air at 0.6 kg/cm2 driven through “V” belt or directly coupled through flexible coupling to a TEFCmotor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles a/c supply.

Air piping shall comprise of pipes droppers/ laterals with M S (epoxy coated) Header complete with all fittings such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle flanges etc cutting chases & making good in Plant Room. All submerged piping will be SS-304

Non clog type air dispersion system capable of handling 3-5 cfm of air with oxygen transfer efficiency of 3-4% per/meter water depth. Air dispersion grid shall be assembled in modular form so that they can be replaced / repaired Fine /coarse aeration bubble diffusers as required. For sludge holding tank - 1 No.

SBR reactor tank- 1 Nos.

Air dispersion system shall be provided for Sludge holding Tank and SBR reactor Tanks SS 304 : Submerged air piping MS Epoxy : Air piping, Filters & other Eqp. PVC piping ASTM SCH 40 :Pumped effluent & tank overflow pipe line

Supplying, installing, testing & commissioning of Submersible Jet Areator in Eqalization Tank 1 No. Capacity : 100 M3/Hr MOC :CI

Supply, installation, testing & commissioning of motorized Moving Decanter to suit SBR tank with MOC SS-304 with scum guard and connected with ultrasonic level transmitter & ultrasonic level element for automatic control etc. complete as required.

Providing and fixing of ozonation system comprising of ozonator, recirculation pumps, mixing arrangement, tanks, oxygen concentrator to dose ozone @ 50 gram per hr. The system should have a single cell & supplied complete with appropriate dosing pumps , valves, piping, fittings, chemical dosing tank etc.

Supply, installation, testing & commissioning of vertical inline multistage pumping set (Imported) with Stainless steel-304 body, Stainless steel-304 impeller, Stainless steel-304 casing, shaft of Stainless steel-316 and C.I. base & head with mechanical seal, connected to a TEFC induction motor suitable for 415+/- 10% volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundations, 80x40 mm I section base plate bolted to cement concrete foundations complete.Vendor to submit performance curves and technical catalogue of the proposed model for review and information. Filter Feed Pumps Capacity : 15 M3 / Hr Head : 25 M Set of Two Pumps (1 Working + 1 Standby)

Supplying, installing, testing and commissioning of MSEP vessel filter with all necessary accessories. Filter shall be suitable for minimum working pressure of 5 kg / cm2 and shall include media, standard fittings like pressure gauges, sampling cock, rinse drain, vacuum breaker etc. The MS sheet thickness for shell shall be min. 8 mm and for dishess shall 10 mm. The internal surfaces of tank shall be treated with epoxy coaing and external surface with primer and anticorrosive enamel paint (Min. 2 coats). with frontal piping shall be 100 mm dia MSEP along with valves PN 1.0, test cock, air inlet for back washing and preesure gauges at inlet and outlet. Multigrade Pressure Sand Filter Flow Rate = 15 M3 / Hr Filteration velocity : 15Cum/Hr/Sqm Filter HOS : 1800 MM Filter Diameter : 1250 MM.

Activated Carbon Filter Flow Rate = 15 M3 / Hr Filteration velocity : 15 Cum/Hr/Sqm Filter HOS : 1800 MM Filter Diameter : 1250 MM.

Supply, installation, testing and commissioning of Filter Press of plate as required (size 24"x 24" x 23 nos plate for reference) with screw feed pumps of 2 m3/hr with adequate head (1Working+1Standby) with interconnecting piping and poly dosing system all complete.

Supply, installation testing and commissioning of Magnetic flow meter suitable for 170 KLD Plant with preamplifier and microprocessor including necessary cabling, conduit, etc complete suitable for raw sewage application.

Electrical panel With PLC Control Supply, installation, testing & commissioning of the PLC based control panel with interlocking arrangement with supply pumps,suction pumps, modulating or shut-off valves including necessary wiring, magnetic switches & sensors complete to make the system functional with following interlocking Construction: Compartmentalized Type Skid Mounted, MCC Cum PLC Control panel will be free standing; vertical, fabricated from CRCA steel sheet 14/16 G conforming to degree of protection IP-52 or better. Cable entry will be from bottom. Colour shade - RAL 7032 System Voltage: 380 to 410 Volts & 50HZ ( 415 V ±10% , AC, 50 HZ ±5% for India ). Surge protection to be provided at every applicable point. PLC: The Programmable Logic Controller [PLC] shall consist of a PLC hardware, with 16k (min) program memory shall be protected by a backup battery with further memory protection from an EEPROM. HMI: 5.5 Inch Colour Touch screen HMI, will be mounted on A Man-Machine Interface Terminal (MMI) shall be mounted on the front of the main control panel for control of the activated sludge plant. It will provide a display of the process parameters and equipment status. The display will have an associated keypad. The system will allow operator changes to set points and control of equipment. The terminal shall include an alarm annunciation with a dedicated alarm page and allow acknowledgment of alarms.

Supplying & Fixing of Cables , Conector, Cable Trays, to make Electrical Installation Complete. Necessary cable alleys, internal / cabling, wiring, cabling from MCC to various pumps / equipment and interlocking, earthing and earthing pits for all equipment

Ultrafiltration System - 6 KL/Hr - For Generating 80 KL Water for Flushing UF Module (Hollow Fibre -outside in type porocity 0.1 to 0.01 micron) including micron cartridge filter in PP housing, Pneumatic Valve, PLC Electrical Panel, flow meter, compressor and all other accessories making the system complete Flow rate : 6 cum/hr Output Inlet TSS :- 10-30 mg/lt Filtration Flux :- 45 lt/m2/hr Membrane Area - 64 M2 as per approved makes Membrane MOC - PVDF / PES Membrane Type :- Pressure Feed Mambrane 0.01-0.04 Micron rating type, Out to in process Make UF Membrane - Norit / Pureflow / Koch / Dow / GE No. of UF Membrane - As Per Manufacturer

UF Feed Pump Capacity 7 M3/hr each (1 W + 1 SB) Head 20-25 Mts RPM 2900

Supply, installation, testing & commissioning of UF pre fine filtration. It can be micron filter or Bag filter as per vendor design. The MOC of housing of filter shall be PP

Supplying, installing, testing, commissioning of centrifugal Vertical UF Backwash pumps with Complete SS - 304 with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, strainer at suction. The pump shall be suitable for 415±10% volts 3 phase AC supply . Capacity : - 10 M³/h Head : - 18- 20 m No. of Pumps: 1 No Note-CIP pumps can be common with item no.c

Supplying, Installation, testing and commissioning of chlorine dosing system compromising of Sintex Tank with inlet/ outlet connection, piping and valves alongwith metering pump of 6 LPH for dosing.

Supply, Installation, testing and commissioning of CEB / CIP dosing station including dosing tank, pumps complete in all respect as per UF memrbane specification requirement

Supply installation commissioning of PLC control panel with all automation required like Pneumatic valves, piping in uPVC PLC and other required accessories. Make PLC - Delta, Pneumatic Valve / Solenoid Valves, uPVC Pipe.

MS epoxy coated skid for the complete plant

Supply, installation & commissioning of HDPE backwash tank of 500 Litre capacity including required level controller inlet, outlet, overflow and drain connection.

Water Supply, Drainage Pumps & Water Treatment Equipments Supply, installation, testing & commissioning of vertical inline multistage pumping set (Imported) with Stainless steel body, impeller, casing, shaft and C.I. base & head with mechanical seal, connected to a TEFC induction motor suitable for 415+/- 10% volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundations, 80x40 mm I section base plate bolted to cement concrete foundations complete.Vendor to submit performance curves and technical catalogue of the proposed model for review and information. Filter Feed Pump ( Dom. Water) at Water Supply Pump Room Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 4.0 LPS Head 25 M. HP 3.0 HP Approxi.

Domestic Water Transfer For Right Side at Pump Room Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 3.0 LPS Head 75 M. HP 5.0 HP Approxi.

Domestic Water Transfer For Left Side at Pump Room Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 3.0 LPS Head 75 M. HP 5.0 HP Approxi.

Flushing Water Transfer For Right Side at STP Pump Room Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 2.0 LPS Head 75 M. HP 3.0 HP Approx.

Flushing Water Transfer For Left Side at STP Pump Room Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 2.0 LPS Head 75 M. HP 3.0 HP Approxi.

Softener Feed Pump ( Cooling Tower) at STP Pump Room Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 2.0 LPS Head 25 M. HP 1.5 HP Approxi.

Soft Water Transfer Pump at STP Pump Room Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 2.0 LPS Head 75 M. HP 3.0 HP Approxi.

Irrigation Pumps at STP Pump Room Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 4.0 LPS Head 40 m HP 5 HP Approx..

Providing, installing, testing and commissining of variable speed (VSPS) hydropneumatic system mounted on a common base plate comprising of vertical centrifugal pumping set with S.S body, stainless steel impeller and mechanical seal, shaft directly coupled to a TEFC induction motor suitable for 400/440 volts, 3 phase, 50 cycles AC supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundation, one No. microprocessor based controller, dedicated variable frequency drive for each pump, one No.remote sensors, pressure transducers, sequence running cotroller, dry running Protection,motor control centre, necessary power and control cabling from MCC to pumps including required rating of MCB, one No. 60 litre capacity M.S diaphragam tank with interchangeable butyl rubber membrane,complete in all respects including stainless steel grade 316 pipe suction and delivery headers and isolation/ control valves( ball valves/butterfly valves/ Nan return valves/ vibration eliminators etc as required) , power box, equipped with fuses/ isolators/circuit breakers as required. The entire Hydropneumatic system shall be factory fitted. Hyd. System for Domestic Water Supply at Right Side Terrace Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 5.0 LPS Head 20 M. HP 3.0 HP Approxi.

Hyd. System for Domestic Water Supply at Left Side Terrace Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 4.0 LPS Head 20 M. HP 2.0 HP Approxi.

Supply, installing, testing and commissioning of submersible open impeller non-clog pumps with C.I.body and to TEFC submersible motor for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphragm and bend, vertical discharge pipe, guide pipe and chain in built level controller, sequence running controller, arrangement for both pumps together inacase of emenegency, audible hooter for failure or flooding, dry running Protection complete in all respects., painting, testing and commissioning complete with approved quality and make as required as per instruction of site incharge. (Pumps shall be installed in a set of two pumps One working and One standby) Basement & Pump Room Drainage Pumps (Pumps to be suitable to handle solids upto 30 mm size) Capacity - 4.0 LPS (Each) Head - 20 M H.P. - 2.0 HP Approx.

Sewage Sump Pumps (Pumps to be suitable to handle solids upto 40 mm size) Capacity - 4.0 LPS (Each) Head - 20 M H.P. - 3.0 HP Approx.

Supply Installation,Testing & Commissioning of vertical self supporting Filter fabricated from MS sheet as per IS: 2825, ((minimum thickness of shall 6 mm and dished end 8 mm)) pressure gauges, sample cock, GI class 'C' face piping, CI butterfly valves and all accessories , with initial charge of filter media including anthracite, painting inside with epoxy paint and outside with two coat of red oxide primer and two or more coat of synthetic enamel paint, testing and commissioning complete. Dual Media Filter For Domestic Water Supply Capacity- 14400 LPH Filtration rate- 14000 LPH/Sqm. Filter dia approx. - 1500 MM Working pressure: 3.0 Kg/sq cm. Test pressure : 4. 5 Kg/sq cm

Activated Carbon Filter For Domestic Water Supply Capacity- 14400 LPH Filtration rate- 14000 LPH/Sqm. Filter dia approx. - 1500 MM Working pressure: 3.0 Kg/sq cm. Test pressure : 4. 5 Kg/sq cm

Supply Installation,Testing & Commissioning of "Cation" ion exchange Water Softener fabricated from MS plate as per IS: 2825 (minimum thickness of shall 6 mm and dished end 8 mm) complete with initial charge of resins , GI class 'C' face piping, CI butterfly valves, pressure gauge, hydraulic brine injector, accessories, painting inside with epoxy paint, including 500 liters capacity PVC / HDPE brine tank suitable for 2 regeneration capacity, testing and commissioning complete with resins of approved quality and make. Softener For Cooling Tower Water Supply Hardness- Inlet- 500-600 PPM Outlet- Less than 5 PPM Capacity- 7200 LPH Regeneration period 12 hrs. Quantity of soft water between two regenerations = 86400 lit Working pressure: 3.0 Kg/sq cm. Test pressure : 4. 5 Kg/sq cm

Supply Installation,Testing & Commissioning of metering pump type chemical doser with 100 lits. HDPE chemical grade solution tank,injection fitting assembly,suction and delivery hose upto the point of injection, capacity 0-6 lph, complete in all respects. Chlorination of Domestic Water

Supplying, installing, testing and commissioning controllers with low voltage relays, stainless steel probes and PVC shroud wiring from tank top to probes of required. Level Controller For Water Supply Pump: To start pump when water level is low in Domestic Water U.G. tank and shut off pump when Domestic Water U.G. tank is full. Also to stop when water level is low in raw water underground tank.

Level Controller For Sump Pumps: To start pump when water level is high in sump and shut off pump when sump is empty. Both pumps are start when sump is over flowing.

Providing and fixing GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete. 50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing & fixing butterfly valve tested to a pressure not less than 25 Kg/Sq.cm. Including rubber gasket, 2 nos. Table-E flanges, nuts, bolts, washers & painting complete as required. 50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing & fixing dual plate CI wafer type check valve tested to a pressure of 25 Kg/sqcm. Including rubber gasket, 2 nos. table-E flanges, union, nuts, bolts, washers & painting complete as required. 50 mm dia

65 mm dia

80 mm dia

Providing and fixing resilient rubber neoprene lined style arch vibration eliminators suitable for raw water upto 45 deg.C. Temperature working pressure upto 20 Kg/Sqcm. 50 mm dia

65 mm dia

80 mm dia

Providing and fixing heavy duty armoured cables 1.1 KVA grade including necessary support clamps at ceiling level and connection lugs complete in all respects. Power cable Copper 3 core 10 sq.mm

Power cable Copper 3 core 6 sq.mm

Power cable Copper 3 core 4 sq.mm

Control cable copper 2 core 1.5 sq.mm

Reverse Osmosis (RO) for best Quality Drinking Water. Taurus-100 LPH do 100 Litres Storage

Taurus-250 LPH do 100 Litres Storage

Supply, installation, testing and commissioning of double wall insulated stainless steel water storage tank (inner sheet is SS 316 & outer sheet of SS-304), thickness of sheet as per manufacturer specification, placed at terrace level with inlet, outlet, overflow connection complete with 25 mm dia bend for vent, ball valve for scour, mosquito proof brass overflow grating and 600 mm dia manhole cover with locable arrangment completeas per direction of Engineer-in-charge. 1000 Litres Capacity for RO Water

1500 Litres Capacity for RO Water

Fire Hydrant System Providing and fixing mild steel pipes conforming to I.S.1239 (Heavy class) including all fittings like anchor fastners, couplings, bends, elbows, tees, flanges etc. welding as required, application of anti-corrosive treatment to buried pipes by 4 mm thick multi layer PYPKOTE membrane applied over a coat of primer as per manufacture's recommendations, including necessary trenching, refilling etc. complete. 80 mm dia

150 mm dia

Providing, laying, jointing, testing and commissioning of following sizes of MS Heavy Duty pipes conforming to IS: 1239 with all accessories like all fittings (standard GI/MS fitting with welded/Screwed joint shall be used on the pipes as per local bye lows) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fasteners) or angle iron, G.I. pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between & fire sealent compound at either end all as per Engineer in charge. / Consultants requirements including cutting holes and chases in brick and making good the same to original conditions complete in all respects. All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwire and then supply of the same shall also be included for rates under this head. Including two coats of synthetic enamel paint of approved shade over a coat of primer. Prior to application of primer the surface should be cleaned for any dirt, rusts, rough substance etc. Including painting of legends both direction arrow as per the approval of the Engineer in charge. 25 mm dia IS: 1239

80 mm dia IS: 1239

100 mm dia IS: 1239

150 mm dia IS: 1239

Providing & fixing SS fire hydrant single landing valve with 80 mm NB flanged inlet ( Table-E Flange) , SS spindle controlled 63 mm dia female instantaneous outlet type. SS coupling, blank cap, chain, twist release type lug & all accessories Conforming to IS standards. Including flanged tapping from wet rise complete as required.Single Landing Valve (For Internal & External Hydrants)

Providing and fixing first aid fire hose reel wall mounting swinging type fitted with 20 mm dia 30 m long high pressure ( 10 Kg/cm2) themo plastic hose tube conforming to IS: 12585 Type II with 5 mm outlet Gun Metal nozzle with shut off valve (I.S. 884-1969).

Providing and fixing of Non-percolating flexible hose (RRL type-'A' with EPDM Lined) ISI marked (IS:636) 63 mm dia x 15 M long complete with instantaneous type stainless steel 63 mm dia. IS marked Male and female couplings (IS:903) bound and rivetted to hose pipe with copper rivets and 1.5 mm copper wire.

Providing and fixing standard short size stainless steel branch pipe with SS nozzle 16 mm dia outlet with standard instantaneous type 63 mm dia coupling.(IS:903)

Providing and fixing of gun metal Fire Brigade connection (Suction collecting head) consisting of 63 mm dia instantaneous type male coupling with built-in check valves and 150 mm dia.flanged outlet complete with bolts, nuts and rubber insertions as required as per IS:904-1983. (One for fire tank, One for sprinkler riser & One for wet riser connections) Four Way

Providing and fixing of gun metal fire Brigade Suction Hose coupling (Draw-out Connection) with nut for female coupling as per IS:902- 1974 complete with 100 mm dia. G.I. Suction pipe and 100 mm dia. 1No. C.I. Foot valve flanged (to be connected to static water tank).

Providing and fixing of Air cushion tank (air-vessel) 250 mm dia. x 1.0 M high with dished top made of minimum 6 mm thick M.S. pipe/plate complete with 25 mm dia brass Air Valve (Ball valve, pressure guage type), 25 mm dia. Stop with brass stop cock, nipple, tees, elbow and all accessories as required including fixing brackets.

Providing and fixing 25 mm dia. forged brass ball valve suitable for test pressure of not less than 15 kg / sq.cm. Cost shall be inclusive of providing necessary union / flange connection).

Providing and fixing of Weather proof hose cabinets fabricated from 16 g M.S. Sheet with full glass door and mortise locking arrangement , suitable to accommodate one Hydrant landing valve, 2 nos. 15 M long hose and 1 No branch pipe. The cabinet shall be painted with one coat of primer and finished stove enamelled "Fire Red", "Fire Hose" written on front including suitably mounted on a raised masonry platform as required. (Approx 0.75mx0.6 m x 0.25 m).

Providing and fixing MS partly glazed single/double hung lockable shutter fabricated from MS section as required with 5 mm thick glass for fire station complete including stove enamelled painting of door and frame and words "Fire Hydrant" written on glass, suitable to accommodate 2 Hydrant landing valves, 1 fire hose reel, 2 nos.15m long 63 mm dia hose,1-branch pipe, 1no. fire man's axe, fire extiguishers 2 nos, including suitably mounted on a raised masonry platform as required. (Approx.size 0.90 m x 2.1m )

Providing and fixing dial type pressure gauge with isolation cock and pipe at hydrant station. Dial diameter 100 mm caliberation, 0-15 kg

Providing & fixing butterfly valve tested to a pressure not less than 25 Kg/Sq.cm. Including rubber gasket, 2 nos. Table-E flanges, nuts, bolts, washers & painting complete as required. 80 mm dia

150 mm dia

Providing & fixing dual plate CI wafer type check valve tested to a pressure of 25 Kg/sqcm. Including rubber gasket, 2 nos. table-E flanges, union, nuts, bolts, washers & painting complete as required. 150 mm dia

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Fire Sprinkler System Providing, laying, jointing, testing and commissioning of following sizes of MS Heavy Duty pipes conforming to IS: 1239 with all accessories like all fittings (standard GI/MS fitting with welded/Screwed joint shall be used on the pipes as per local bye lows) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fasteners) or angle iron, G.I. pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between & fire sealent compound at either end all as per Engineer in charge. / Consultants requirements including cutting holes and chases in brick and making good the same to original conditions complete in all respects. All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwire and then supply of the same shall also be included for rates under this head. Including two coats of synthetic enamel paint of approved shade over a coat of primer. Prior to application of primer the surface should be cleaned for any dirt, rusts, rough substance etc. Including painting of legends both direction arrow as per the approval of the Engineer in charge. 25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing and fixing 15 mm dia gunmetal sprinkler head with quartz bulb and set to operate at specified temperature. Temperature of operation 68 deg. C. Pendent/Upright type

Side wall type ( Normal Throw)

Semi concealed type with two piece adjustable rosette plate.

Providing and fixing 15 mm dia forged brass window nozzle type sprinkler head (K-23, with an angle of 180 Degree) with a flow rate of 40 LPM at pressure of 3.0 Kg/cm2 .

Providing and fixing of Deluge valve with automatic alarm system suitable for 150 mm dia pipe including with all necessary accessories to be connected with control valve drain and test valve as per manufacturer's design.

Providing and fixing installation valve with turbine type automatic alarm to be connected with control valve drain and test valve as per manufacturer's design. 150 mm dia.

Providing and fixing 25 mm dia inspecting & testing assembly with built in bye pass arrangement and connection to drain line. (Giocomini)

Providing & fixing butterfly valve tested to a pressure not less than 15 Kg/Sq.cm. Including rubber gasket, 2 nos. table-E flanges, nuts, bolts, washers & painting complete as required. 80 mm dia ( Lever Operated)

100 mm dia ( Lever Operated)

150 mm dia ( Lever Operated)

Providing and fixing electricaly operated flow indicating switches System Sensor in sprinkler branch line on each floor with necessary junction box installed in accessible place. (Wiring from switches to panel not included) 150 mm dia

Providing and fixing of copper conductor PVC covered control cables from individual flow switches on each floor to annunciation panel installed in fire control room including sleeves, cable clips, supports for horizontal runs making connection to each switch complete. 2 core 1.5 Sqmm

Providing and fixing dial type pressure gauge with isolation cock and pipe. Dial diameter 100 mm, caliberation 0-15 kg

Providing and fixing of Air cushion tank (air-vessel) 250 mm dia. x 1.0 M high with dished top made of minimum 6 mm thick M.S. pipe/plate complete with 25 mm dia brass Air Valve (Ball valve, pressure guage type), 25 mm dia. Stop with brass stop cock, nipple, tees, elbow and all accessories as required including fixing brackets.

Providing and fixing flexible Sprinkler Hose Corrugated braided Type for fire Sprinklers, with 1” Inlet Nipple BSPT, ½” Outlet Reducer BSPT, 0.7 m Square Support Bar & Brackets 700 mm length flexible pipe

1000 mm length flexible pipe

1200 mm length flexible pipe

1500 mm length flexible pipe

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25 mm dia .

Fire Pumps & Accessories Supply, installation, testing and commissioning of electric motor driven high pressure centrifugal fire hydrant /sprinkler pump, suitable for automatic operation consisting of the following: Horizontal single/multi stage, single outlet centrifugal split casing pump , suitable for operation on 415 volts ± 6%, 3 phase, 50 HZ AC supply. The installation shall be complete with flexible coupling and coupling guard as required. Fire pump shall have CI casing, CS diffusers, bronze impeller (hard finished and dynamically balanced) and SS (304) shaft with mechanical seal, capable for head as required to ensure a minimum pressure of 3.5 Kg/Sqcm at the farthest or top most hydrant / sprinkler. The installation shall be complete with necessary pressure gauge on delivery side. Squirrel cage induction motor, TEFC type suitable for operation on 415 volts, 3 phase 50 HZ A.C supply, for the above pump with synchronous speed of 1450 RPM, conforming to IP 55 protection & class B insulation. The motor shall conform to IS 325-1978 (up to date). Common base frame for (a) and (b) from M.S. Channel for required size. Suitable RCC / cement concrete foundation with plaster and MS angle epoxy coated edging (design and drawing to be provided by the Contractor. Complete with anti-vibration arrangement of cushy foot mountings. Capacity- 2850 LPM Head- 100 M. HP- 105 HP ( Approximate)

Supply, installation, testing and commissioning of Diesel Engine driven fire pump suitable for automatic operation comprising of the following and conforming to BS 649/IS 10002 all amended upto date. Horizontal single/multi stage, single outlet centrifugal split casing pump , suitable for operation on 415 volts ± 6%, 3 phase, 50 HZ AC supply. The installation shall be complete with flexible coupling and coupling guard as required. Fire pump shall have CI casing, CS diffusers, bronze impeller (hard finished and dynamically balanced) and SS (304) shaft with mechanical seal, capable for head as required to ensure a minimum pressure of 3.5 Kg/Sqcm at the farthest or top most hydrant / sprinkler. The installation shall be complete with necessary pressure gauge on delivery side. Heat exchanger cooled (secondary cooling) diesel engine of speed 1500 RPM suitable for the above pump with automatic starting mechanism and other accessories including fuel tank (fabricated from 6mm MS sheet, painted with two coats of synthetic enamel paint over a coat of primer) of capacity adequate to sustain pump operation for 8 hours continuous working. The tank shall be fitted with Magnetic oil level indicator, MH with cover, drain valve, air vent including structural supports (painted with approved shade), 2 Nos. x 12 volt battery (alternator of engine and panel is suitable for 12 volt current rating) with stand heat exchanger with necessary piping connections & fittings complete as required.Two nos 50 mm dia PRV with 4 nos of valve and pressure guage to supply water to heat exchanger. Common base frame for (a) and (b) from M.S. Channel for required size. Suitable RCC / cement concrete foundation with plaster and MS angle epoxy coated edging (design and drawing to be provided by the Contractor. Complete with anti-vibration arrangement of cushy foot mountings. Capacity- 2850 LPM Head- 100 M.

Supply, installation, testing and commissioning of jockey pump (pressurisation pump) comprising of the following: Vertical centrifugal multi stage pump, suitable for operation on 415 volts ± 6%, 3 phase, 50 HZ A.C supply. The installation shall be complete with Flexible coupling and coupling guard, complete as required. The pump casing shall be CI, shaft shall be SS & impeller/ shaft sleeve/casing wearing ring shall be bronze. The pump shall be provided with mechanical seal The system shall be complete with necessary pressure gauge with gun metal shut off cock on delivery side. Squirrel cage induction motor TEFC type for operation on 415 V, 3 phase 50 Hz AC supply for the above pump with a synchronous speed of 2900 RPM as required. Common base plate for (a) and (b) from M.S. channel as required size. Suitable RCC / cement concrete foundation with plaster and MS angle epoxy coated edging (design and drawing to be provided by the Contractor. Complete with anti-vibration arrangement of cushy foot mountings. Flow : 180 LPM, Head : 100 mts (1 for Hydrant System & 1 for Sprinkler System )

Supply, installation, testing and commissioning of electric motor driven high pressure centrifugal water curtain pump, suitable for automatic operation consisting of the following: Horizontal single/multi stage, single outlet centrifugal end suction pump , suitable for operation on 415 volts ± 6%, 3 phase, 50 HZ AC supply. The installation shall be complete with flexible coupling and coupling guard as required. Fire pump shall have CI casing, CS diffusers, bronze impeller (hard finished and dynamically balanced) and SS (304) shaft with mechanical seal, capable for head as required to ensure a minimum pressure of 3.5 Kg/Sqcm at the farthest or top most hydrant / sprinkler. The installation shall be complete with necessary pressure gauge on delivery side. Squirrel cage induction motor, TEFC type suitable for operation on 415 volts, 3 phase 50 HZ A.C supply, for the above pump with synchronous speed of 2900 RPM, conforming to IP 55 protection & class B insulation. The motor shall conform to IS 325-1978 (up to date). Common base frame for (a) and (b) from M.S. Channel for required size. Suitable RCC / cement concrete foundation with plaster and MS angle epoxy coated edging (design and drawing to be provided by the Contractor. Complete with anti-vibration arrangement of cushy foot mountings. Curtain Pump 2850 LPM @ 50 M. Head

Providing & fixing 150 mm diameter MS Class ‘C’ for diesel engine exhaust pipe (including all fittings, clamps, steel support) of suitable dia for the diesel engine. The pipe shall be provided insulation with fibre glass wool and wraped with 24g. aluminium sheet complete with all respect.

Supply, Installation, Testing & Commissioning of double flanged vertical air vessel fabricated shell from 10 mm thick & dished ends 12 mm thick M.S.plate, suitable for working pressure of 18 kg/cm2 and test pressure of 27 kg/cm2, 450 mm dia and 2.00 m high for fire pumps complete with four nos dual setting pressure switches to operate jockey and main pumps at drop of pressure as given in the specifications.

Providing and fixing alarm system for fire pumps comprising audible hooter and red blinking lamp wired to pressure switch including cost of pressure switch mounted on air vessel complete in all respects.

Providing and fixing heavy duty PVC insulated, PVC armoured conductor cables 1100 V grade including necessary support clamps and connection lugs complete in all respects. Power cable 3.5 core 150 sq mm aluminium conductor armoured cable

Power cable 3 core 10 sq mm Copper conductor armoured cable.

Providing and fixing 300 mm dia suction header fabricated from 8 mm thick M.S. plate rolled and welded pipe suction header with inlets & outlets of 200/150/100/80 mm dia as required,all outlets and ends with flanged connections blank flanges, painting with one coat of zinc chromate primer and two or more coats of synthetic enamel paint to give an even shade, structural supports as required common for fire hydrant and sprinkler systems.

Providing and fixing 250 mm dia delivery header fabricated from 8 mm thick M.S. plate rolled and welded, with with 150/100/80/50 mm dia inlets & outlets as required , including painting with one coat of zinc chromate primer and two or more coats of synthetic enamel paint to give an even shade and required structural supports. All outlets and inlets to be provided with MS flanges, the cost of which shall be included in the rate of header.

Providing & fixing butterfly valve tested to a pressure not less than 25 Kg/Sq.cm. Including rubber gasket, 2 nos. table-E flanges, nuts, bolts, washers & painting complete as required. 80 mm dia ( Lever Operated)

100 mm dia ( Lever Operated)

150 mm dia ( Lever Operated)

200 mm dia. ( Gear Operated)

250 mm dia. ( Gear Operated)

Providing & fixing dual plate CI wafer type check valve tested to a pressure of 15 Kg/sqcm. Including rubber gasket, 2 nos. table-E flanges, union, nuts, bolts, washers & painting complete as required. 80 mm dia.

100 mm dia

150 mm dia

250 mm dia

Providing and fixing resilient rubber neoprene lined single arch vibration eliminators with unit control suitable for raw water upto 450C temperature working pressure 12 kg and test pressure 20 kg/cm2. 80 mm dia.

100 mm dia

150 mm dia

Providing and fixing 200 mm dia CI `Y' strainer with bronze perforated sheet basket including rubber gasket, flanges, nuts, bolts and washers, complete as required.

Fire Extinguishers Providing and fixing carbon-di-oxide type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to IS:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. Capacity 4.5 Kg.

Providing and fixing mechanical foam type fire extingushers consisting of welded M.S. trolley mounted cylindrical body, squeeze lever discharge valve fitted with pressure discharge hose, discharge nozzle, trolley etc., ISI marked as per IS:IS:13386 finished externally with red enamel paint. Capacity 50 lit (D.G.Room)

Providing and fixing carbon-di-oxide fire extingushers trolley mounted with all accessories internal discharge tube,high pressure discharge hose,discharge nozzle, ISI marked as per IS:2878 finished externally with red enamel paint. Capacity 22.5 kg.

Providing and fixing ABC Powder type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to IS:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. Capacity 6.0 Kg.

POINT WIRING Wiring for Light/Fan/Call Bell Point with 2X1.5 sq.mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid ISI marked steel conduit pipe complete. Short point upto 3.00 metre length.

Medium point upto 6.00 metre length.

Long point upto 10.00 metre length.

Wiring for circuit wiring with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (finolex/RR Kabel/Nicco/Anchor or Equivalent make as approved by the Dept.) in surface/recessed ISI marked steel conduit pipe wiring system. with 3X1.5 sq.mm cable in 20 mm dia. Rigid Steel conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in ISI marked steel conduit pipe including earth continuity in surface/recessed conduit wiring system. With 2X2.5 sq.mm. + earth continuity with 1X1.5 sq.mm cable in 20 mm. dia. Rigid steel conduit.

With 2X4 sq.mm. + earth continuity with 1X2.5 sq.mm cable in 20 mm. dia. Rigid steel conduit.

With 2X6 sq.mm. + earth continuity with 1X4 sq.mm cable in 25 mm. dia. Rigid steel conduit.

With 2X10 sq.mm. + earth continuity with 1X6 sq.mm cable in 25 mm. dia. Rigid steel conduit.

With 2X16 sq.mm. + earth continuity with 1X10 sq.mm cable in 32 mm. dia. Rigid steel conduit.

Wiring for Drawing submain line with P.V.C insulated single core unsheathed industrial (multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/ RR Kabel or equivalent make as approved by the Dept. ) including earth continuity in surface/ recessed ISI marked steel conduit pipe wiring system. With 4X2.5 sq.mm. + earth continuity with 2X1.5 sq.mm cable in 25 mm. dia. Rigid steel conduit.

With 4X4 sq.mm. + earth continuity with 2X2.5 sq.mm cable in 25 mm. dia. Rigid steel conduit.

With 4X6 sq.mm. + earth continuity with 2X4 sq.mm cable in 25 mm. dia. Rigid steel conduit.

With 4X10 sq.mm. + earth continuity with 2X6 sq.mm cable in 25 mm. dia. Rigid steel conduit.

With 4X16 sq.mm. + earth continuity with 2X10 sq.mm cable in 32 mm. dia. Rigid steel conduit.

Wiring to 5 pin 6 Amps plug point with 1.5 sq. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexuble bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed ISI marked steel 20 mm. dia. conduit pipe wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete. Short point upto 3.00 metre length.

Medium point upto 6.00 metre length.

Long point upto 10.00 metre length.

Wiring to 5/6 pin 16 Amps plug point with 4 sq. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexuble bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system including earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20mm. dia. steel conduit (AK G or equivalent as approved by the Dept.) Short point upto 3.00 metre length.

Medium point upto 6.00 metre length.

Long point upto 10.00 metre length.

Wiring for twin control light point with 1.5 sw. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid ISI marked steel conduit pipe including 6 Amp flush type 2 way switch ( Anchor penta/Gold medal /Kolor Kany.Kom/Havells or equivalent make as approved by the dept.) GI/MS switch board (ISI marked) with phenolic laminated sheet cover, ceiling rode etc complete.Long point upto 10.00 metre length.

Supplying and fixing 19 mm dia ISI marked steel conduit pipe (AKG or equivalent as approved by the Dept.) in surface/recessed including cutting the wall and making good the same ti its original architectural finish.

Supplying and fixing 25 mm dia ISI marked steel conduit pipe (AKG or equivalent as approved by the Dept.) in recessed including cutting the wall and making good the same ti its original architectural finish.

Supplying and fixing 32 mm dia ISI marked steel conduit pipe (AKG or equivalent as approved by the Dept.) in recessed including cutting the wall and making good the same ti its original architectural finish.

Supplying and fixing 38 mm dia ISI marked steel conduit pipe (AKG or equivalent as approved by the Dept.) in recessed including cutting the wall and making good the same ti its original architectural finish.

Supplying and fixing 50 mm dia ISI marked steel conduit pipe (AKG or equivalent as approved by the Dept.) in recessed including cutting the wall and making good the same ti its original architectural finish.

Supplying and fixing of following Metal Boxes for Model Range Legrand (Arteor), Anchor (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) in surface / recessed system complete as per direction of department. 1-2 Module Type Metal

3 Module Type Metal

6 Module Type Metal

8 Module Type Metal

12 Module Type Metal

Supplying including installation of socket outlet 6/10/13 Amps INTERNATIONAL SOCKET, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying with fitting and fixing of 16 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying with fitting and fixing of 6 amp one way modular clip in bell push MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying with fitting and fixing of 16 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying with fitting and fixing of 6/10 amp two way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying fitting and fixing industrial plug & socket in surface mounted SPN sheet steel powder painted MCB DB incorporated with MCB DIN rail, neutral link Earth bar of the following rating of DP MCB complete with making necessary connection etc. as specified and directed by the Dept. 20A Capacity. (ABB, Schneider MG, legrand, Hager make)

Supplying fitting and fixing industrial plug & socket in surface mounted TPN sheet steel powder painted MCB DB incorporated with MCB DIN rail, neutral link Earth bar of the following rating of 4P MCB complete with making necessary connection etc. as specified and directed by the Dept. (ABB, Schneider MG, legrand, Hager make).20A Capacity 20A Capacity

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door(IP-43) surface mounting SPN MCB DB incorporated with bus-bar, Neutral link, Earth Bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved , specified & directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make). 8 way SPN double door

12 way SPN double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door(IP-43) surface mounting vertical per phase isolation (PP) DB incorporated with bus-bar 125A, Neutral link, Earth Bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved , specified & directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 6 way TPN (8+6+18) double door

8 way TPN (8+6+24) double door

12 way TPN (8+6+36) double door

Supplying with fitting and fixing single pole 10KA 240/415V 50Hz MCB of the following capacity complete with making necessay connection as approved, specified and directed by the Dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (Schneider MG, legrand, Hager, Crabtree Xpro make) C Series 6 to 32A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 30mA sensitivity DP RCCB 25A

100/300mA sensitivity DP RCCB 25A

Supplying with fitting and fixing Surge protector of max operation voltage 350V at 400 V network for maximum discharge current 40KA with operator indicator and draw out cartridge of (Schneider or equivalent make), of the following ways complete with making necessary connection as approved, specified and directed by the dept. Surge protection Max operating voltage 340V Standard type 1P+N

Supplying, installation of pre galvanised sheet steel std thickness 1.6mm under floor trunking including necessary nuts & bolts, washer etc. as required, as directed and specified by the department. ( MK/ LEGRAND make) Size 100X38X1.6/1 compartment

150X38X1.6/2 compartment

225X38X1.6/3 compartment

250X38X1.6/3 compartment

300X38X1.6/3 compartment

JUNCTION BOX 150X150X60 - 75 mm Depth

250X250X60 - 75 mm Depth

300X300X60 - 75 mm Depth

350X350X60 - 75 mm Depth

JOINT SLEEVE 100/1/6 FOR 38mm

150/2/6 FOR 38mm

225/3/6 FOR 38mm

250/3/6 FOR 38mm

300/3/6 FOR 38mm

Cross over/ Junction box Cross over 250X250X60 - 75mm 3 compartments

Cross over 300X300X60 - 75mm 3 compartments

Cross over 350X350X60 - 75mm 3 compartments

Supplying including fitting and fixing of TV SOCKET, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying including fitting and fixing of following star rated A.C. ceiling fan complete with all accessories like down rod, canopy etc of following sweeps with making necessary connection cable as approved by Deptt.s etc as required complete and as directed by the department as required complete etc. (Without regulator). (Orient / PSPO / Usha / Crompton / Havells/ ATC / V Gaurd.) Energy efficient 5-star 1200 mm sweep. (Orient / PSPO / Usha / Crompton / Havells/ ATC / V Gaurd.)

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 160A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 63A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING "Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make)" 63A

"Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series" 6 to 32A

"Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series" 40A

INCOMMING / OUTGOING "Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make)" 63A

"Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series" 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

"Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series" 6 to 32A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING "Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make)" 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make)C Series 40A

INCOMMING / OUTGOING "Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A"

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING "Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A"

"Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series" 40A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING "Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A"

"Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series" 40A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING "Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A"

"Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series" 40A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING "Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A"

"Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series" 40A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 63A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING "Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make)" 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 63A

"Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series" 40A

INCOMMING / OUTGOING "Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make)" 63A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING "Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make)" 63A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 63A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz 4P RCCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 100/300mA sensitivity FP RCCB 63A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 63A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING "Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A"

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series 40A

Design & Supply of IP-55 Rising Mains with plug-outlets in every 850mm on both side of trunking of following capacity with Aluminium conductor, TPN with 100% neutral, 1000V IP-55, 50 hz, housing made from 1.5mm hot-galvanized sheet steel treated according to UNI 10327 and painted with RAL 7035 resins with high resistance to chemical agents including End cover, supports and two runs of GI earth bar and complying with IEC-60439. (Legrand/C&S or equivalent as approved by the deptt.) 1600 amp Rising Mains (SC Rating for 1 Sec-80 KA.)

800 amp Rising Mains (SC Rating for 1 Sec-42 KA.)

Supply of following capacity End Feed Unit Made of 1.6 mm thick sheet steel enclosure dully painted with powder coating to existing rising mains complete with provision of fixing MCCB. (Legrand/C&S or equivalent as approved by the deptt.) 1600 amp Rising Mains (SC Rating for 1 Sec-80 KA.)

Supply of following capacity TPN Tap off box Made of 1.6 mm thick sheet steel enclosure dully painted with powder coating to existing rising mains complete with provision of fixing MCCB. (Legrand/C&S or equivalent as approved by the deptt.) 63 A Tap-off Box with inbuilt Disconnection. (Legrand/C&S or equivalent as approved by the deptt.) on cover (W/o MCCB.)

100 A Tap-off Box with inbuilt Disconnection. (Legrand/C&S or equivalent as approved by the deptt.) on cover (W/o MCCB.)

160 A Tap-off Box with inbuilt Disconnection. (Legrand/C&S or equivalent as approved by the deptt.) on cover (W/o MCCB.)

250A Tap-off Box with inbuilt Disconnection. (Legrand/C&S or equivalent as approved by the deptt.) on cover (W/o MCCB.)

Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, neutral adjustable with earth fault protection without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 63A

50KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

50KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

MAIN & SUB MAIN CABLES Supply and laying of following size solid aluminium conductor up to 10 sq.mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured /armour (Aluminium for single core up to 70 sq.mm balance Aluminium strip, Galvanized for cables up to 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm balance all galvanized steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) Core-2 (A2XWay, A2XFaY) 6 sq.mm two core armoured cable

10 sq.mm two core armoured cable

35 sq.mm 3 and 1/2 core armoured cable

50 sq.mm 3 and 1/2 core armoured cable

70 sq.mm 3 and 1/2 core armoured cable

95 sq.mm 3 and 1/2 core armoured cable

120 sq.mm 3 and 1/2 core armoured cable

185 sq.mm 3 and 1/2 core armoured cable

300 sq.mm 3 and 1/2 core armoured cable

25 sq.mm four core armoured cable

Supply and laying of following size power / control copper cables, solid copper conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured/armoured (Galvanised for cable up to 10x1.5 sq.mm, 8x2.5 sq.mm, 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm, balance all all galvanised steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) 4 sq.mm four core armoured cable

6 sq.mm four core armoured cable

10 sq.mm four core armoured cable

16 sq.mm four core armoured cable

Supply & Laying of following sizes of 1.1KV grade multistranded copper conductor FRLS insulated cable including termination complete as required in existing cable tray. 1C x 70 sq.mm PVC Insulated cu wire including end termination.

1C x 25 sq.mm PVC Insulated cu wire including end termination.

1C x 16 sq.mm PVC Insulated cu wire including end termination.

Supply, Installation, Testing & Commissioning of Earthing Junction Box size - 400mm x 300mm x 80mm made out of 16 SWG CRCA sheet with seven tank process & powder coating, earthing link (32mmx6mm copper strip), front door with glass as complete as required.

Supplying Fitting and Fixing of (Dowells / Commet make) Double compression brass gland with nickel. Weatherproof (CBW) Size:8-10, 3/4''

Supplying Fitting and Fixing of (Dowells / Commet make) Single compression brass gland heavy duty. Single Compression Brass Gland Heavy Duty. Size:1''

Single Compression Brass Gland Heavy Duty. Size:1-1/8''

Single Compression Brass Gland Heavy Duty. Size:1-1/4''

Single Compression Brass Gland Heavy Duty. Size:1-3/8''

Single Compression Brass Gland Heavy Duty. Size:1-1/2''

Single Compression Brass Gland Heavy Duty. Size:1-3/4''

Single Compression Brass Gland Heavy Duty. Size:2-1/4''

Single Compression Brass Gland Heavy Duty. Size:2-3/4''

Perforated RM30 Medium Duty Return Flange Cable Tray with Nos Splice RM 30 8-M6 X Gutter Bolt & Nuts upto 300mm and 3 Nos Splice, RM30 12 -M6 X Gutter Bolt & Nuts Above 300mm including stand off bracket. Size of Tray (in mm) 100

Size of Tray (in mm) 150

Size of Tray (in mm) 300

Size of Tray (in mm) 450

Size of Tray (in mm) 600

Size of Tray (in mm) 750

Size of Tray (in mm) 900

Inter/Exter Bend 100

Inter/Exter Bend 150

Inter/Exter Bend 300

Inter/Exter Bend 450

Inter/Exter Bend 600

Inter/Exter Bend 750

Inter/Exter Bend 900

STAND OFF BRACKET 100

STAND OFF BRACKET 150

STAND OFF BRACKET 300

STAND OFF BRACKET 450

STAND OFF BRACKET 600

STAND OFF BRACKET 750

STAND OFF BRACKET 900

SUPPLY & FIXING OF LIGHT FIXTURES & FANS INTERNAL LIGHTING. Supply, Installation, Testing & Commissioning of Recess LED Downlighter made of pressure die cast aluminum housing with high efficiency reflector, LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=90lumens/watt, 650 Lumen, Life of fixture (Including Driver) : 50K Hrs. @ L70B50 Lumen maintenance, CCT - 6500 (SDCM<5), CRI >80, PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.0KV The fixture design should comply with IS10322, (INSTAPOWER Cat No: 144 173 09.04)

Supply, Installation, Testing & Commissioning of Recess LED Downlighter made of pressure die cast aluminum housing with high efficiency reflector, LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt, 1200 lumen, Life of fixture (Including Driver) : 30K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<5), CRI >80, PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.0KV The fixture design should comply with IS10322. (INSTAPOWER Cat No: 144 173 09.05)

Supply, Installation, Testing & Commissioning of Recess Dali Dimmable LED Downlighter made of pressure die cast aluminum housing with high efficiency reflector, LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt, 1200 Lumen, Life of fixture (Including Driver) : 50K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<5), CRI >80, PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.0KV The fixture design should comply with IS10322. (INSTAPOWER Cat No: 144 173 09.05)

Supply, Installation, Testing & Commissioning of Recess Spot LED Downlighter made of pressure die cast aluminum housing with high efficiency reflector, LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=90lumens/watt, 470-500 Lumen, Life of fixture (Including Driver) : 25K Hrs. @ L70B50 Lumen maintenance, CCT-3000 (SDCM<5), CRI >80, PF >0.90,Minimum system Lumens 600. Philips 59325 SKY SPOT LED RECESSED LIGHT or equivalent.(INSTAPOWER Cat No: 201.01.14)

Supply, Installation, Testing & Commissioning of 60W LED Sandilier Rectangular Ceiling Mounted light as complete as required. (Make:- Philips CAT No.- Philips 59087 Sparkle And Shine LED Chandelier (L-950 x W-750 x H-182) or equivalent

Supply, Installation, Testing & Commissioning of 44W LED Sandilier Rectangular Ceiling Mounted light as complete as required. (Make:- Philips CAT No.- Philips 59086 Sparkle And Shine LED Chandelier (L-850 x W-850 x H-309) or equivalent

Supply, Installation, Testing & Commissioning of Recess LED Downlighter made of pressure die cast aluminum housing with high efficiency reflector, LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt, 1200 Lumen Life of fixture (Including Driver) : 30K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<5), CRI >80, PF >0.90, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.0KV The fixture design should comply with IS10322. (INSTAPOWER Cat No: 144 173 09.05)

Supply, Installation, Testing & commissioning of Recess LED Downlighter made of pressure die cast aluminum housing with high efficiency reflector, LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt, 1000 Lumen, Life of fixture (Including Driver) : 30K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<5), CRI >80, PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.0KV The fixture design should comply with IS10322 ( INSTAPOWER Cat No: 144 173 09.05)

Supply, Installation, Testing & commissioning of Symetrical Wide Beam Luminiare,LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=125lumens/watt, Life of fixture (Including Driver) : 50K Hrs. @ L70B50 Lumen maintenance,Design to work at Ambient temperature (Ta) of 45Degree, CCT - 6500 (SDCM<5), CRI >80, PF >0.90 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 3.0 KV. The fixture design should comply with IS10322, EMC/EMI compliance maintaining driver leakage current as per as per IEC 60598, Protection of Fixture:- IP65,IK05,Class I protection with Minimum system Lumens 14500. ( (INSTAPOWER Cat No: 231 135 107.16)

Supply, Installation, Testing & Commissioning of Recess Spot LED Downlighter made of pressure die cast aluminum housing with high efficiency Aluminum reflector, fixture should have minimum efficacy at System level (Not Chip Level) >=76/85lumens/watt with wide beam angle of 36Deg , Life of fixture (Including Driver) : 40K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<5), CRI >80, PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.0KV The fixture design should comply with IS10322, EMC / EMI compliance maintaining driver leakage current as per as per IEC 60598,Minimum system Lumens 2000. (INSTAPOWER Cat No: 202.01.15)

Supply, Installation, Testing & Commissioning of Recess Spot LED Downlighter made of pressure die cast aluminum housing with high efficiency Aluminum reflector, fixture should have minimum efficacy at System level (Not Chip Level) >=76/85lumens/watt with wide beam angle of 36Deg , Life of fixture (Including Driver) : 40K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<5), CRI >80, PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.0KV The fixture design should comply with IS10322, EMC / EMI compliance maintaining driver leakage current as per as per IEC 60598,Minimum system Lumens 2000. (INSTAPOWER Cat No: 202.01.15)

Supply, Installation, Testing & Commissioning of Recess LED Downlighter dali dimmable made of pressure die cast aluminum housing with high efficiency reflector, LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt, Life of fixture (Including Driver) : 30K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<5), CRI >80, PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.0KV The fixture design should comply with IS10322, EMC / EMI compliance maintaining driver leakage current as per as per IEC 60598, Minimum system Lumens 1800. (INSTAPOWER Cat No: 144 173 09.07)

Supply, Installation, Testing & Commissioning of 12 watt LED Mirror Light as complete as required. (INSTAPOWER Cat No: 24 09 02.144)

Supply, Installation, Testing & Commissioning of Recess Spot LED Downlighter made of pressure die cast aluminum housing with high efficiency Aluminum reflector, fixture should have minimum efficacy at System level (Not Chip Level) >=76/85lumens/watt with wide beam angle of 36Deg , Life of fixture (Including Driver) : 40K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<5), CRI >80, PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.0KV The fixture design should comply with IS10322, EMC / EMI compliance maintaining driver leakage current as per as per IEC 60598,Minimum system Lumens 4000.(INSTAPOWER Cat No: 202.01.16)

Supply, Installation, Testing & Commissioning of Surface Mounted Linear LED fitting made of CRCA Housing ,LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=123lumens/watt, Life of fixture (Including Driver) : 40K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500, CRI >83 (R9>0), PF >0.97 & THD<15%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 3.0KV LED lamp beam angle to be maintained 150Deg. The with inbuilt protection with Fuse which protect the LED tube from damage and failure in case of voltage surge or spike. ,Minimum system Lumens 1600. (INSTAPOWER Cat No: 25 09 02.288).

Supply, Installation, Testing & Commissioning of Surface Mounted Linear LED fitting made of CRCA Housing ,LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=123lumens/watt, Life of fixture (Including Driver) : 40K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500, CRI >83 (R9>0), PF >0.97 & THD<15%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 3.0KV LED lamp beam angle to be maintained 150Deg. The with inbuilt protection with Fuse which protect the LED tube from damage and failure in case of voltage surge or spike. ,Minimum system Lumens 3200. (INSTAPOWER Cat No: 25 09 02. 500)

Supply, Installation, Testing & Commissioning of Surface Mounted Linear LED IP65 fitting made of Virgin Polycarbonate housing & Non Yellowing PC Diffuser ,LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt, Life of fixture (Including Driver) : 50K Hrs. @ L70B50 Lumen maintenance, CCT 6500 (SDCM<5), CRI >80 , PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 3KV The fixture design should comply with IS10322, EMC / EMI compliance maintaining driver leakage current as per as per IEC 60598,Minimum system Lumens 4000. (INSTAPOWER Cat No: 25 09 02. 500)

Supply, Installation, Testing & Commissioning of Recess LED 600x600mm fitting made of white CRCA powder quoted finish with fully covered by PMMA Acrylic Lumio Diffuser, LED Used shall be SMD type and fixture should have minimum efficacy at System level >=100lumens/watt, Life of fixture : 50K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<5), CRI >80 , PF >0.95 & THD<10%, Fixture must be office compliant & have to comply to UGR<19 value for optimim glare.an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.5KV The fixture design should comply with IS:10322 & Must be EMC / EMI compliance maintaining driver leakage current as per as per IEC 60598, Minimum system Lumens 3000. (INSTAPOWER Cat No: 10 112 23.36).

Supply, Installation, Testing & Commissioning of Recess LED 600x600mm Dali/Non Dali fitting made of white CRCA powder quoted finish with fully covered by PMMA Acrylic Lumio Diffuser, LED Used shall be SMD type and fixture should have minimum efficacy at System level >=130lumens/watt, Life of fixture : 50K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<4), CRI >80 , PF >0.95 & THD<10%, Fixture must comply to UGR<16 value for optimim glare.an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.5KV The fixture design should comply with IS:10322 & Must be EMC / EMI compliance maintaining driver leakage current as per as per IEC 60598, Minimum system Lumens 4100. (INSTAPOWER Cat No: 10 112 23.45).

Supply, Installation, Testing & Commissioning of Surface/Suspended Linear Slim (width 60mm) Non Dali dimmable LED fitting made of Extusion Alu. Housing with anodised coating ,LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=110lumens/watt, Life of fixture (Including Driver) : 50K Hrs. @ L70B50 Lumen maintenance, CCT 6500 (SDCM<5), CRI >80 , PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 3KV The fixture design should comply with IS10322, EMC / EMI compliance maintaining driver leakage current as per as per IEC 60598,Minimum system Lumens 2300.(INSTAPOWER Cat No: 149 123 78.20)

Supply, Installation, Testing & Commissioning of Surface/Suspended Linear Slim (width 60mm) Non Dali dimmable LED fitting made of Extusion Alu. Housing with anodised coating ,LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=110lumens/watt, Life of fixture (Including Driver) : 50K Hrs. @ L70B50 Lumen maintenance, CCT 6500 (SDCM<5), CRI >80 , PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 3KV The fixture design should comply with IS10322, EMC / EMI compliance maintaining driver leakage current as per as per IEC 60598,Minimum system Lumens 2300. (INSTAPOWER Cat No: 149 123 78.20)

Supply, Installation, Testing & Commissioning of Surface/Suspended Linear Slim (width 60mm) Non Dali dimmable LED fitting made of Extusion Alu. Housing with anodised coating ,LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=110lumens/watt, Life of fixture (Including Driver) : 50K Hrs. @ L70B50 Lumen maintenance, CCT 6500 (SDCM<5), CRI >80 , PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 3KV The fixture design should comply with IS10322, EMC / EMI compliance maintaining driver leakage current as per as per IEC 60598,Minimum system Lumens 2300. (INSTAPOWER Cat No: 149 123 78.20)

Supply, Installation, Testing & Commissioning of LED Bulkhead Fixture made of pressure die cast aluminum housing with high efficiency reflector, LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt, Life of fixture (Including Driver) : 30K Hrs. @ L70B50 Lumen maintenance, CCT - 6500 (SDCM<5), CRI >70, PF >0.95 , an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.0KV The fixture design should comply with IS10322, Minimum system Lumens 700.(INSTAPOWER Cat No: 59 152 08.84)

Supply, Installation, Testing & Commissioning of Self contained emergency light units 1x9 watt double sided for wall / ceiling mounting with suspension / mounting kit, lamps, inbuilt standby battery (for 2 hours backup) and battery charger etc. in suitable enclosure. (INSTAPOWER Cat No: 30 25 08.30)

Supply, Installation, Testing & Commissioning of Recessed Foot Light as complete as required.(INSTAPOWER Cat No: 61 03.12)

Supply, Installation, Testing & Commissioning of 4 watt per meter (300 lumen per meter) LED cove Light with high efficiency electronic driver. (Make Delta Light Cat No- 300 92 52 93)

Supply, Installation, Testing & Commissioning of Supply of Recess LED Downlighter made of pressure die cast aluminum housing with high efficiency reflector, LED Used shall be SMD type and fixture should have minimum efficacy at 110 lumens/watt, Life of fixture (Including Driver) : 50K Hrs. @ L70B80 Lumen maintenance, CCT - 4000 (SDCM<3), CRI >90, PF >0.95 , The fixture design should comply with IS10322, EMC / EMI compliance maintaining driver leakage current as per as per IEC 60598,Minimum system Lumens 1075 ,Beam angle 33 Deg, Delta Light Deep Ringo 202 272 811 932 W)

Supply, Installation, Testing & Commissioning of 1x16.8W watt Track light with high efficiency electronic driver 48V DC. (Make Delta Light, Cat No- 414 361 21 931 W)

Supply, Installation, Testing & Commissioning of Surface mounted conductor track 2F with 48V DC in aluminium powder coated to pure white protection class I , L 1000 (segmented) width 29mm and height H15mm, with flexible connector of matching color (to connect two segment ) electrical wire III phase circuit, protection class I, the connector to give flexibility of maximum 90 degree unidirectional. Make : Delta Light Cat no 200 21 41 W

Supply, Installation, Testing & Commissioning of Electronic Buzzer as complete as required.

Supplying, Fitting and fixing of occupany sensor of the following atageories as per required and directed by the department. (ABB/ Panasonic/ mk/ anchor/ crabtree/ Hager/ Panasonic or equivalent make as approved by deptt. Indoor presence detection with 360 degrees angle of detection and 2 relays (one for light and one for HVAC), range up to 7 meter at 2.5 meter ceiling height.

DATA, TELEPHONE, Wi-Fi SYSTEM Supply, installation, testing and commissioning of following LAN networks equipments. Solid Copper Cable 6, 4 pair, UTP 305m SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Patch Panel Cat 6 UTP Keystone-24 Port- Loaded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Patch Cord Cat 6 UTP Gray 1m- Moulded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Cat 6 Keystone UTP Jack with Dust Cover-White SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Back Box-(Surface Mount Box) For Single and Dual SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

APW Cyber Rack Networking Equipment Rack APW President Enclosure, 600mmW CYBERACK 42U/800mmD (CRCA Steel Frame with Aluminium Profiles & 2 Nos. of Removable Side Panels with followwing items:- Top cover with cable entry-1no.-Bottom cover with cable entry-1no.-19" Mounting Angles-2 pairs., Finish: Powder coated to 80 microns; Matt Finish. Colour: BLACK with, Load rating capacity -500 Kgs., Front side vented glass door and rear full perforated steel door with locks. " PDU 10*5/15A-01 Nos., Fan Housing Unit with 4 Fans-01 Set, Mounting Hardware (Set of 20)-1 Set, Castor with Brake- 2Nos., Castor without Brake - 2 Nos., Earthing Kit - 01 Set, Cable Manager 19" 1U - 2 Nos.

Patch Cord Cat 6 UTP Gray 2m- Moulded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Supply , Installtion , Testing and comissioning of 27U wall mount rack with fans , 2 cable managers, satationary shelf , 2 Nos of hardware pkts. Approved Makes: Poweride/MTS/Rittal/APC/APW

Supply of IP Based voice Communication System with 04 Port Voicemail ,04 Port FXS ,04 Port FXO ,1 PRI Trunk lines (30 Ch) Circuit with CLIP Facility ,320 IP users License ,01 Nos. IP Operator Console,100 Party Conference ,Speed Dial, Music on Hold , Internal/ External ring difference ,Call Barring, Call Pickup, - Redundant server in active-Active mode. Approved Makes: Tadiran/Cisco /Polycom/Juniper/Cambium

Supply of Type 1 IP Phone . Graphic LCD display with backlight 3 user accounts with multi-line appearance keys Local and company-wide phone directories. Approved Makes: Tadiran/Cisco /Polycom/Juniper/Cambium

Supply of Type 2 IP Phone 1 VoIP account , Full duplex speaker phone, IPV6, 2xLAN, PoE . Approved Makes: Tadiran/Cisco /Polycom/Juniper/Cambium

Supply, Installation, Testing & Commissioning of Core Switch with switching capacity of 1.4Tbps, forwarding performance of 1Bpps with 32x 1/10G SFP+ ports plus 4x 40G QSFP+ ports from day 1, dual hot swappable internal power supply, 60K IPv6 routes and 48K IPv6 multicast routes. Should support advance layer 3 (RIPng, OSPF, BGP and MPLS) with 1 year support. Stack Module/40 Gig Optics and all other Cables should be included in Day 1. Approved Make : Cisco/ Impulse / Juniper / Extreme/ Arista

Supply, Installation, Testing & Commissioning of 24 Port POE+ Access Switches with switching capaticy of 128 Gbps, forwarding performance 95 Mpps, having 24 x 10/100/1000BASE-T PoE-plus(RJ45) with minimum PoE budget of 370W and 4x 10G SFP+ uplink ports . Should support min 2GB internal DRAM, 2GB internal Flash memory,32K MAC address, 1K IPv6 Multicast Routes, Should have static Routes from day 1.One year support. Approved Make : Cisco/ Impulse / Juniper / Extreme/ Arista

Supply, Installation, Testing & Commissioning of fiber Modules 1000BASE Approved Make : Cisco/ Impulse / Juniper / Extreme/ Arista.

Supply , Installation , Testing and Comissioning of 3X3 MIMO , 802.11 a/b/g/n Indoor Wi-Fi- Access point, dynamic radio management. Approved Makes: Cisco/Juniper/ Extreme/ Cambium/ Der Weiser.

Supply , Installation , Testing and comissioning of wireless LAN Controller supportable for AP upgradable for Aps in standalone and 100 Aps in high availability mode. Approved Makes:Cisco/Juniper/Extreme/Cambium/Der Weiser.

Supply, Installation, Testing & Commissioning of Internet Web Security solution with minimum of 100 users from day one with one years of subscription / support and flexibility to scale up to 1000 users, having 99.9% uptime with each level redundancy, single pane of glass for reporting with minimum 6 months of logs and must be Leaders in Gartner Magic Quadrant in the last 3 consecutive years (2015, 2016 and 2017) and includes following features as per detailed specification: a) Web Security b) Full SSL Inspection c) Next Generation Firewall d) Sandboxing e) Bandwidth Control f) Cloud Applications Visibility g) Mobility Approved Makes: Zscaler/ Checkpoint/Palo Alto/Cisco/Juniper

Supply , Installtion , Testing and comissioning of armoured 6 core multimode OFC cable for interfloor switch connectivity.

Supply , Installtion , Testing and comissioning of 6 port loaded LIU with adaptor plates , pigtel cables for connections.

Supply , Installtion , Testing and comissioning of 24 port loaded LIU for core switch to access switch connectivity over fiber.

Supply , Installtion , Testing and comissioning of SC-LC multimode fiber patch cord.

LIGHTNING PROTECTION AS PER IEC 62305 / IS IEC 62305 Supply 8 mm round aluminium conductor for horizontal lightning protection - run in roof. Model : AL8. Make : Hakel / APS

Supply of roof conductor holder for 8 mm round aluminium conductor made of Gun Metal for horizontal installation. The distance between each holder should be min of 1.5 mtr. Model : APSRCS50. Make : Hakel / APS

Supply of Cross connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model : APSCCRC50 , Make : Hakel /APS

Supply of T connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model : APSCCRC50 , Make : Hakel /APS

Supply of L connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model : APSCCRC50 , Make : Hakel /APS

Supply of straight connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model : APSPCRC50, Make : Hakel / APS

Supply of Expansion piece to compensate the expansion of round 8 mm Al conductor when temperature variation . Connection should be in every 20 mtr. Model : APSEXP50 , Make : Hakel/APS

Supply of fixing glue for fixing of roof conductor holder .

Supply of Expansion piece connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model : APSCEP50- Make : Hakel /APS

DOWN CONDUCTOR AS PER IEC 62305 Supply of 8 mm round aluminium conductor as a down conductor mounted in the surface of wall which will carry the lightning current to earth pit. Model : AL8. Make : Hakel / APS

Supply of Down conductor holder for 8 mm round aluminium conductor of min distance between the wall to the conductor will be of 50 mm. The distance between each holder should be min of 1.5 mtr. Model : APSRCH50 Make : Hakel /APS

Supply of Test Joint Point for 8 mm round aluminium conductor , the size should be of 25 x 3 x 150 mm copper in ABS boxes. Model : APSTLBCU. Make : Hakel / APS

EARTHING AS PER IEC 62561- 2 & 7 Supply of UL approved low carbon high tensile steel rod with copper coating of min 254 micron JK Chemrode - 317 CBR the dia should be 17.2 mm with length of 10 feet ( 3000 mm) . The rod shall be as per IEC 62561-2 and approved by UL 467. The rod shall be tested from NABL lab for current discharge not less then 46kA peak. The Chemrode shall be surrounded with 50 kg ( 2 bag) of Earth enhance materiel JK Activer+ according to IEC 62561-7 and the Chemical resistance value shall not increase more then 0.064 Ωm and same will be tested from NABL lab. Make :APS/JK

FIRE ALARM SYSTEM (ADDRESSABLE TYPE) Supply, Installation,Testing & Commisioning of Microprocessor based X loop fire alarm control panel EN approved expandable upto 18 loops fully networkable with each loop capable of taking 125 devices, 4 line x 40 character alpha-numeric liquid crystal display .The panel shall be soft addressable type . The panel shall be able to give pin point location of all fire/fault conditions. Further, the panel must be able to automatically switch off respective control switches when ever any alarm is triggered. The panel shall have in built rectifier, Loop cards,provision for externel & internal printer(if required), L C D unit to indicate Fire/Fault Signal with address and analog output, built in printer to log all fire or fault events complete in all respects, integral SMF lead acid batteries with sealed cells of 24 V capable of running for a minimum of 8 hours with integral battery charger complete as required and as per specification. The fire alarm panel shall be suitable for software integration with BMS & PA system. 10 Loops

Supply, Installation,Testing & Commisioning of Fire Graphics Software to be loaded on PC to monitor the Floor wise Fire Detection System.

Supply, Installation,Testing & Commisioning of Networkable Repeater Panel (LCD indicator panel) with 2 line X 20 characters alpha numeric LCD display with all commands such as reset, mute, silence with suitable battery backup complete as required.

Supply, Installation,Testing & Commisioning of Analog Addressable Intelligent multisensor detector with two inbuilt optical smoke sensors with light angles as well as additional heat detector sensor with decentralise intelligence, soft addressable Photothermal type with inbuilt fault isolator as per NFPA style 7 wiring complete with base as required.

Supply Installation, Testing & Commissioning of Intelligent addressable photothermal detector with blue colour LED for very early warning with inbuilt isolator as per NFPA7 style 7 wiring & standard base complete as per specification.

Supply, Installation, Testing & Commisioning of Analogue Addressable Intelligent Heat Detector with fixed & rate of rise temperature function with decentralise intelligence , soft addressable type, with inbuilt fault isolator as per NFPA style 7 wiring complete with base as required.

Supply Installation, Testing & Commissioning of Intelligent addressable Manual Call Point / Pull station complete as per specification.

Supply, installation, testing and commissioning of addressable control module complete as per specification.

Supply, installation, testing and commissioning of addressable monitor module complete as per specification.

Supply Installation, Testing & Commissioning of wall mounting loop powered addressable type hooter with all accessories.

Supply Installation, Testing & Commissioning of Response Indicator.

Supply Installation, Testing & Commissioning of fire fighter main console at control room including power supply and accessories.

Supply Installation, Testing & Commissioning of Fire fighters telephone handset.

Supply Installation, Testing & Commissioning of Fire fighters telephone jack.

SITC of 2x250W Class-D Amplifier with 4 independent channels and can provide automatic re-settable overcurrent, overload, overheating, overvoltage, under-voltage and DC protection Approved Makes : Bosch Praesedio / Honeywell - X618/ Ateis - IDA

SITC of Network Resource Interface, 4 channels network audio source, 32 dry contacts in and 8 try contacts out for Fire Alarm Interface

SITC of 6W Ceiling mount with max SPL1M/1W 96dB . Frequency response of 160Hz-20KHz. The speaker shoud have tappings at 6W/3W

SITC of 6W Wall mount with max SPL1M/1W 96dB . Frequency response of 160Hz-20KHz. The speaker shoud have tappings at 6W/3W

Supply, Installation, Testing & Commissioning of 2C x 1.5 sq.mm Fire Survival unarmoured cable (300/500V) with Class-2 Copper conductor having Mineral ceramic glass fire barrier tape covered by an extruded layer of Cross-linkable Low Smoke Zero Halogen (LSZH) insulation as per EI-5 Of BS EN 50363 along with ATC drain wire, aluminium tape screening and LSZH outer sheath as per BS 7629-1 & BS-5839-1 (latest edition). Outer sheath should be Anti Rodent/Anti Termite. Should retain circuit integrity as per BS 8434-2 (930 deg C for 120 mins on single sample) including end termination etc as complete as required. (For Fire & PA System)

CCTV SYSTEM- Supply, installation, testing and commissioning of following LAN networks equipments. Solid Copper Cable 6, 4 pair, UTP 305m SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Patch Panel Cat 6 UTP Keystone-24 Port- Loaded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Patch Cord Cat 6 UTP Gray 1m- Moulded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Cat 6 Keystone UTP Jack with Dust Cover-White SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Back Box-(Surface Mount Box) For Single and Dual SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

APW Cyber Rack Networking Equipment Rack APW President Enclosure, 600mmW CYBERACK 42U/800mmD (CRCA Steel Frame with Aluminium Profiles & 2 Nos. of Removable Side Panels with followwing items:- Top cover with cable entry-1no.-Bottom cover with cable entry-1no.-19" Mounting Angles-2 pairs., Finish: Powder coated to 80 microns; Matt Finish. Colour: BLACK with, Load rating capacity -500 Kgs., Front side vented glass door and rear full perforated steel door with locks. " PDU 10*5/15A-01 Nos., Fan Housing Unit with 4 Fans-01 Set, Mounting Hardware (Set of 20)-1 Set, Castor with Brake- 2Nos., Castor without Brake - 2 Nos., Earthing Kit - 01 Set, Cable Manager 19" 1U - 2 Nos.

Supply, Installation, Testing and Commissioning of UL Listed , ONVIF profile S & G , 1/2.8" CMOS, IP Vari Focal Dome Camera , Full, HD 3 MP , 2.8-12 mm Motorized Varifocal Lens, 30 FPS , Triple Stream with Edge Based Analytics , True Day/Night with IR Cut Filter with auto switch , Shutter Speed 1/5s ~ 1/20,000 s, IR Illuminator 30 Meter Min Effective Range, 120DB Wide Dynamic Range, Alarm 1/1, Audio 1/1, SD Card, H.265, H264 Compression, PoE, IP66 , Vandal Proof IK10 etc. Approved Makes: Allgovision/ Pelco/ Avigilon/ Impulse/ Axis.

Supply, installation, testing and commissioning of UL Listed , ONVIF profile S & G ,1/2.8" CMOS, IP Vari Focal Bullet Camera , Full, HD 3 MP Resolution , 2.8-12 mm Motorized Varifocal Lens , 30 FPS , Triple Stream with Edge Based Analytics , True Day/Night with IR Cut Filter with auto switch , Shutter Speed 1/5s ~ 1/20,000 s, IR Illuminator 30 Meter Min Effective Range, 120DB Wide Dynamic Range, Alarm 1/1, Audio 1/1, SD Card, H.265, H264 Compression, PoE, IP66 etc. Approved Makes: Allgovision/ Pelco/ Avigilon / Impulse/ Axis.

Supply, installation, testing and commissioning of UL Listed ONVIF profile S &G , 1/2.8" CMOS Box type camera , external lens 5mm to 50 mm, Full, HD 3 MP Resolution ,3MP@25FPS , 2 MP @ 50 FPS , Quad Stream with Edge Based Analytics, Shutter speed 1 ~ 1/10000 sec, SD card support , P-iris, ONVIF profile S & G etc. .Approved Makes :Allgovision/ Pelco/ Avigilon / Impulse/ Axis.

Supply , Installation , Testing and Comissioning of 6 MP , Fish eye Camera ,ONVIF profile S & G , UL,CE,FCC certified , 1/1.8" CMOS lens , 1.55 mm focal length , shutter speed :1 ~ 1/10000 sec , Quad stream , Frame rate : 6MP @ 25 fps , 2 MP @ 50 fps , Digital Zoom , Two way audio support ,Auto white balance ,Inbuilt IR LED , IR Distance upto 5 mtrs ,IP 66 weather proof , POE. Approved Makes: Allgovision/ Pelco/ Avigilon / Impulse/ Axis.

Supply, installation, Testing and Commissioning of Open Platform ONVIF profile S &G Network Video Recorder, Intel based, Full Rack, RAID 0/1/5/10, @ 2M/30FPS, 1*2.5" SATA + 8 * 3.5" SATA, Throughput: 640 Mbps.1 X HDMI , 1X VGA ,, 1 X mic in , 1 X line out , USB 3.0 x 2 + USB 2.0 x 3 , 1 X WAN port , 1 X LAN port , pre-installed VMS :Approved Makes :Allgovision/ Pelco/ Avigilon / Impulse/ Axis.

Supply, installation, testing and commissioning of UL Listed , ONVIF Compliant 1/2.8" IR PTZ Speed Dome Camera max resolution 3 MP , 0.05 @ F1.6 (Color), 0 (B/W) @ F1.6, Quad Streams, IR Distance 150m, Edge Analytics, 120DB Wide Dynamic Range, H264 Compression, IP66 Motorized Lens 4.3-129mm 30x Optical zoom Audio in/out 1/1, MicroSD slot, IP66 etc. Approved Makes :Allgovision/Pelco/Avigilon / Impulse/Axis.

Supply, Installation, Testing & Commissioning of Core Switch with switching capacity of 1.4Tbps, forwarding performance of 1Bpps with 32x 1/10G SFP+ ports plus 4x 40G QSFP+ ports from day 1, dual hot swappable internal power supply, 60K IPv6 routes and 48K IPv6 multicast routes. Should support advance layer 3 (RIPng, OSPF, BGP and MPLS) with 1 year support. Stack Module/40 Gig Optics and all other Cables should be included in Day 1. Approved Make : Cisco/ Impulse / Juniper / Extreme/ Arista

Supply, Installation, Testing & Commissioning of 24 Port POE+ Access Switches with switching capaticy of 128 Gbps, forwarding performance 95 Mpps, having 24 x 10/100/1000BASE-T PoE-plus(RJ45) with minimum PoE budget of 370W and 4x 10G SFP+ uplink ports . Should support min 2GB internal DRAM, 2GB internal Flash memory,32K MAC address, 1K IPv6 Multicast Routes, Should have static Routes from day 1.One year support. Approved Make : Cisco/ Impulse / Juniper / Extreme/ Arista

Supply, Installation, Testing & Commissioning of 4TB HD Approved Makes: WD, Segate / Toshiba.

Supply, Installation, Testing and Commissioning of Full HD 65" LED Professional Display Panel. Approved Makes: Panasonic, Sony, Samsung.

Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); Memory: 4GB, NON-ECC, 1600MHZ; RAM: 4GB (1x4GB) Non-ECC DDR3 1600MHz SDRAM Memory; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; 20" TFT Monitor; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit. Approved Makes: HP, Dell, IBM.

UPS SYSTEM Supply, Installation, Testing & Commissioing of 80 KVA UPS in paralleling mode at 0.99 input power factor with SNMP card, compatible for BMS connectivity on backnet/MODBUS, Isolation transformer as per specification given in the document with following broad features. THD(i) shall be less than 3% in the entire loading range. UPS shall carry design output at 40 deg. Shall have soft start and hold of for incoming supply. Invertor capability to supply 150% load for 5 sec. Three Phase Input and Three Phase Output. (Input - 340V - 470V, Three Phase, 4 wire. / Output - 400-415 Volt, Three Phase, 4 Wire.) Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case of 12 volt cells. Battery shall be external type with rack and suitable for 30 minute backup on 100% load. UPS shall be compatible for 4 nos unit in parallel operation. (Synchronize). Parallel operation kit shall be supplied with UPS. UPS described as above

Supply, installation, testing & commissioing of 30 KVA UPS at 0.99 input power factor with SNMP card, compatible for BMS connectivity on backnet/MODBUS, inbuilt isolation transformer as per specification given in the document with following broad features. THD(i) shall be less than 3% in the entire loading range. UPS shall carry design output at 40 deg. Shall have soft start and hold of for incoming supply. Invertor capability to supply 150% load for 5 sec. Three Phase Input and Three Phase Output. ( Input - 340V - 470V, Three Phase, 4 wire. / Output - 400-415 Volt, Three Phase, 4 Wire.) Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case of 12 volt cells. Battery shall be external type with rack and suitable for 90 minute backup on 100% load. UPS described as above

Supplying, installation, testing & commissioning of Escalators, speed 0.5 mps, height as per sketch enclosed, 30 degree inclination with step & 2 step flat at each landing, width of 1000 mm, balustrades and base panel of Stainless Steel and complete as required and as per technical specification and drawing enclosed. (For Height 8000 mm).

AUDIO VISUAL SYSTEM FOR 2X250 SEATER AUDIO GROUND FLOOR Supply, Installation, Testing and Commissioning of Active Steerable Columnar Array : Active Column Loudspeaker with onboard DSP, Twenty Four (24) or more transducers with 130Hz-20kHz, AES/DANTE and line-level analog input connectivity, Articulated array configurations with 110-130 degrees horizontal and Vertical 10 - 100 degree Symmetrical or asymmetrical with single of multiple beams (no of modules to match the require angle) vertical coverage, +/- 40 degrees vertical Beam steering angles with application distance of minimum 35 - 40mtr. Max SPL 96dB at 30 meter. Internal / External Interface Module for comission the Digital Steerable Speaker Approved Make: Tannoy / Bose / Meyer Sound / Renkus-Heinz

Supply, installation, testing & Commissioning of Compact Dual 8" or better Installation friendly subwoofer with Freq. Range of 38 Hz - 200Hz or better. It should have an axial Sensitivity of > = 97dB (1W/1m) or more delivering a Max. Calculated SPL(Continuous) of >=123 dB (129dB Peak). The loudspeaker should have a nominal impedance of 8ohm or better and continuous Power Handling of 400W (1600W Peak) or more. The Subwoofer shall be enclosed in Baltic birch plywood with polyurethene paintable grill. Approved Make: Tannoy / Bose / Martin Audio / Renkus-Heinz

Supply, installation, testing & Commissioning of 2 channel class D Networkable Power amplifier with a Max Output Power of 2 x 600W@8 Ohms, 2x1200W@4 ohms, (in scenario of Muliple Channel Amplifier, need to match the reuire amplification power) shall give . 20Hz - 20 KHz, SNR of 104dB or better and THD + N of <0.1% with built in protection such as Limiters, Temperature, DC, Short Circuit, Peak Current Limiters, Turn on delay etc. Built in DSP for Matrix routing, Speaker equalization, Delays, Array EQs etc complete with Ethernet Port for Network Control, programming and monitoring. Approved Make: Labgruppen / Bose / Powersoft / Procella

Supply of 40 channel Digital Mixing Console with 16 mic inputs, 25 bus, 6 Aux outs. Main LCR out and Matrix outputs, 40-Bit floating-point DSP, 24 bit ADC and DAC converters with minimum 112 dB dynamic range, minimum 17 motorised 100 mm faders, Optional wireless remote control for iPhone* and iPad* etc. 32 x 32 channel USB 2.0 audio interface, 8 DCA and 6 mute groups, Built in effect processor, Complete with Built in aur external 100-Band RTA for all Channel/Bus EQ 's, Auto-ranging universal switch-mode power supply. Digital Audio Port fo connectivity with Stage Box Approved Make: Behringer / Yamaha / Soundcraft

Supply, Installation, testing and commissioning of wireless digital Handheld Microphone with 18 or more channel, RF output 80mW or more, super cardiod pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital lavalier Microphone with 18 or more channel, RF output 80mW or more, omni directional pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital Headworn Microphone with 18 or more channel, RF output 80mW or more, omni directional pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital Gooseneck Microphone with 18 or more channel, RF output 80mW or more, Cardioid / super cardiod pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital Gooseneck Microphone charging charging pad can charge minimu 2no. Of microphone simulataneously and operate on network Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital Hadheld , Lapel & Headworn Microphone charging docking station can charge minimu 4no. Of microphone simulataneously and operate on network Approved Make: Sennheiser / Shure / Beyerdynamic

Vocal Handheld wired microphone. Approved Make: Sennheiser / Shure / Beyerdynamic

Heavy duty 2 core 2.5 sqmm copper loudspeaker cable. Approved Make: Sommer / Belden / Canare

Heavy duty 2 core shielded microphone cable, 22AWG Approved Make: Sommer / Belden / Canare

Making of Mike/speaker points on stage Approved Make: Custom / Apprv Eqv

Table stand Approved Make: K&M / Beyerdynamic / Sennhiser

Floor Stand Approved Make: K&M / Beyerdynamic / Sennhiser

19 "Equipment Rack Made of MS for housing of all above equipment , front lockable acrylic door, Fan for colling, Caster wheel base , Complete with MCB including all internal wiring/ interconnection as required Approved Make: Rittal / Valrack / President

FOR 2X250 SEATER PROJECTION GROUND FLOOR SITC of 1-chip DLP LASER Phosphor Multimedia Projection system having, 10000 Lumens (center) 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, 10000:1 Contrast Ratio, inputs: HDBaseT,HDMI, DVI-D, VGA alongwith powered Zoom Lens & projector mountin bracket etc. complete with installation as per the site requirement. Approved Make: Panasonic / Barco / NEC

Motorised Projection Screen with Unity Gain of size 147" (h) x 236" (w), 16:10 Aspect Ratio complete with Low Voltage control module, upto 2' of black drop as per site requirement Approved Make: Dallite / Draper / Stewart

Should have and support 4K UHD, HDBaseT active wall plate with step−in auto switcher for HDMI, VGA and analog audio signals and Output should be in twisted pair format that supports resolutions up to 4K@60Hz (4:2:0). The device has EDID management, easy control options and audio embedding. The unit is a fully−featured with the convenience and simplicity of a wall plate.It should be easy to install with browser−based configuration and single PoE cable for Ethernet connectivity and powering.it should be HDCP cmpliant and support Max. Data Rate - 10.2Gbps (3.4Gbps per graphic channel. Should support Range − Up to 70m in normal mode. Approved Make: Kramer / Lightware / Crestron / Extron / Wyrestrom

Distribution amplifier 1:4 for 4K@60Hz (4:2:0) HDMI 2.0 signals complying with the HDCP 1.4 content protection standard. The unit takes one HDMI input, equalizes and reclocks the signal and distributes it to four identical outputs.Should have Max. Data Rate — 10.2Gbps (3.4Gbps per graphic channel) and Should have 1 USB for firmware upgrade.Device Should have Compliance - HDMI 2.0, HDCP 1.4 and support deep color, x.v.Color, lip sync, 7.1 PCM, Dolby TrueHD, DTS–HD, CEC (OUT 1 only), 2K, 4K, and 3D. Device also have button for EDID setup and status indicators for HDMI input and output connected signals, and power indicator. Approved Make: Kramer / Lightware / Crestron / Extron / Wyrestrom

High−performance, extended−reach HDBaseT PoE transmitter for 4K60Hz (4:2:0) HDMI, Ethernet, RS−232 and IR signals over twisted pair.It converts. It extends video signals to up to 100m (330ft) over CAT copper cables at up to 4K@60Hz (4:2:0) 24bpp video resolution and provides even further reach for lower HD video .Should support a minimum data rate of 10Gbps.HDMI Signal Extension HDMI 2.0 and HDCP 2.2 compliant. Supports deep color, x.v.Color, lip sync, HDMI uncompressed audio channels, Dolby TrueHD, DTS–HD, 2K, 4K, and 3D. EDID and CEC signals are passed through from the source to the display.Multi–channel Audio Extension — Up to 32 channels of digital stereo uncompressed signals for supporting studio–grade surround sound.minimum data rate of 10Gbps Approved Make: Kramer / Lightware / Crestron / Extron / Wyrestrom

4K60 4:2:0 HDMI HDCP 2.2 PoE Receiver with Ethernet, RS–232 & IR over Extended–Reach HDBaseT,It extends video signals to up to 100m (330ft) over CAT copper cables at up to 4K@60Hz (4:2:0) 24bpp video resolution and provides even further reach for lower HD video resolutions.HDMI Signal Extension — HDMI 2.0 and HDCP 2.2 compliant. Supports deep color, x.v.Color, lip sync, HDMI uncompressed audio channels, Dolby TrueHD, DTS–HD, 2K, 4K, and 3D. EDID and CEC signals are passed through from the source to the display.I–EDIDPro-Intelligent EDID Processing — Intelligent EDID handling, processing and pass–through algorithm that ensures Plug and Play operation for HDMI source and display systems. Multi–channel Audio Extension — Up to 32 channels of digital stereo uncompressed signals for supporting studio–grade surround sound.minimum data rate of 10Gbps Approved Make: Kramer / Lightware / Crestron / Extron / Wyrestrom

Wireless collaboration and presentation solution that makes sharing and presenting in meetings easier. With any laptop or mobile device, users can view, edit and comment on documents in real time, share files and chat with individuals or multiple participants simultaneously. The solution can show up to four screens on the main display. and participant can view the main display, edit documents together in real time, share any size file, turn the main display into a digital whiteboard, and more. The solution features iOS mirroring for MacBook, iPad, iPhone, Windows phone and Android device connectivity wirelessly. Device having HDMI input and High quality video streaming, supports full HD 1080p/60Hz. device is capable to connect more than 200 device with secure 1024–bit encryption. device having 4 USB 3.0, 1 LAN on an RJ–45 connector, 1 HDMI Input and 1 HDMI, 1 mini DisplayPort and Audio output. Device having 4GB high Speed memory,4th generation Intel® Dual core 1.4GHz processor and 32GB, solid–state drive with Do not disturb (DND) feature that would enable uninterrupted presentation. Approved Make: Kramer / AMX / Crestron / Wyrestrom

Master/space controller with PoE with Minimum 4 bidirectional RS232, 4 IR, 4 Relays and 4 GP/IO and 1 Ethernet port to control all the devices in the room. Should have inbuilt IR sensor to learn IR commands .The compatible relay controller to control the Projector up down should be supplied as a package (may be from same OEM of controller or different). Should have inbuilt processing power and internal storage to store and process the control program. Should be compatible with any (IOS/Android) wireless or wired Touch screen of any size. Additional ports if required can be added with minimum hassle. Should have the flexibility to add as many user interfaces as required. Should have embedded webpage for control port settings.Should have Status LED to check for Control/Connection status.It should support PoE. Device Has 512MB RAM, 4GB Flash memory.It should have minimum 5 free license if required for iOS/Android application Approved Make: Kramer / AMX / Crestron / Wyrestrom

12−button control keypad, with knob and LCD displays with 12 RGB–color, backlit buttons. custom labeled removable button caps. with Digital knob for volume control.It should have 3 8–characters program–configurable LCD displaysand control processor in-built with 3 RS-232, 2 IR, 2 I/O & 4 relay ports. Device have IR learner in-built,1 mini USB connector for programming and work in sync with primary master room controller.Every button should be configurable and touch sensitive.Should be operable within the temperature range of 0 deg C to 40 deg C.Extra component or equipment maybe added to match the complete specs. Approved Make: Kramer / AMX / Crestron / Wyrestrom

3.5mm to Single IR Emitter Cable Approved Make: Kramer / AMX / Crestron

CAT6A U/FTP 4 shielded twisted pairs ,23AWG solid copper conductor Video & LAN Bulk Cable — Low Smoke & Halogen Free recommended by HDBaseT Approved Make: Kramer / Extron / Belden

Layer 2 Gigabit switch 8 port. Approved Make: HP / Cisco / Netgear

Network router standard quality to create WIFI Approved Make: HP / Cisco / Netgear

Cat6 Cable for Data . Approved Make: Belden / AMP / Punduit

High Speed triple-shielded bonded pairs HDMI Cable with Ethernet Gold Palted Lockable Connector. It support Data Transfer rate of upto minimum 10GBps and upto 48 bit Deep Color. Cable has overall shield against EMI/RFI interference and CL2 flame tested. Approved Make: Kramer / Extron / Crestron / Belden

High Speed triple-shielded bonded pairs HDMI Cable with Ethernet Gold Palted Lockable Connector. It support Data Transfer rate of upto minimum 10GBps and upto 48 bit Deep Color. Cable has overall shield against EMI/RFI interference and CL2 flame tested. Approved Make: Kramer / Extron / Crestron / Belden

FOR MEDIA BRIEFING ROOM AUDIO SYSTEM Supply, Installation, testing and commissioning of Wall Mount multi driver full range loudspeaker with free field frequency range (-10dB) of 70Hz to 18kHz; RMS continuous power handling of 120W better; Nominal dispersion of 120 H X 60 V; full range Sensitivity of 89 Db SPL; Max SPL of 111 dB SPL (117dB peak); Nominal Impedance of 8 ohms; Rugged Birch Plywood enclosure with powder coated steel grille. Approved Make: Tannoy / Bose / Martin Audio / Renkus-Heinz

Wall Brackets Approved Make: Tannoy / Bose / Martin Audio / Renkus-Heinz

Supply, installation, testing & Commissioning of Compact Dual 8" or better Installation friendly subwoofer with Freq. Range of 38 Hz - 200Hz or better. It should have an axial Sensitivity of > = 97dB (1W/1m) or more delivering a Max. Calculated SPL(Continuous) of >=123 dB (129dB Peak). The loudspeaker should have a nominal impedance of 8ohm or better and continuous Power Handling of 400W (1600W Peak) or more. The Subwoofer shall be enclosed in Baltic birch plywood with polyurethene paintable grill. Approved Make: Tannoy / Bose / Martin Audio / Renkus-Heinz

Supply, installation, testing & Commissioning of 2 channel class D Networkable Power amplifier with a Max Output Power of 2 x 600W@8 Ohms, 2x1200W@4 ohms, (in scenario of Muliple Channel Amplifier, need to match the reuire amplification power) shall give . 20Hz - 20 KHz, SNR of 104dB or better and THD + N of <0.1% with built in protection such as Limiters, Temperature, DC, Short Circuit, Peak Current Limiters, Turn on delay etc. Built in DSP for Matrix routing, Speaker equalization, Delays, Array EQs etc complete with Ethernet Port for Network Control, programming and monitoring. Approved Make: Labgruppen / Bose / Powersoft / Procella

Supply, Installation, testing and commissioning of wireless digital Handheld Microphone with 18 or more channel, RF output 80mW or more, super cardiod pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital lavalier Microphone with 18 or more channel, RF output 80mW or more, omni directional pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital Headworn Microphone with 18 or more channel, RF output 80mW or more, omni directional pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital Hadheld , Lapel & Headworn Microphone charging docking station can charge minimu 4no. Of microphone simulataneously and operate on network Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of shotgun microphone, pollar pattern : super-cardioid / lobar / array, Frequency response : 40 Hz to 20 kHz , Min. terminating impedance : 1 kΩ , Equivalent noise level : 23 dB(A) , Acoustics : interference tube transducer, gooseneck length : 180mm or less Approved Make: Sennheiser / Shure / Beyerdynamic

Heavy duty 2 core 2.5 sqmm copper loudspeaker cable. Approved Make: Sommer / Belden / Canare

Heavy duty 2 core shielded microphone cable, 22AWG Approved Make: Sommer / Belden / Canare

Making of Mike/speaker points on stage Approved Make: Custom / Apprv Eqv

19 "Equipment Rack Made of MS for housing of all above equipment , front lockable acrylic door, Fan for colling, Caster wheel base , Complete with MCB including all internal wiring/ interconnection as required Approved Make: Valrack / Rittal / President

FOR MEDIA BRIEFING ROOM PROJECTION SYSTEM Projector: 1-chip DLP Solid state(Laser Phosphor) Projection system with ultra short throw lens having 6000 Lumens, 1920 x 1200 Native Resolution, 10000:1 Contrast Ratio, Lamp Life 20000 hours, Min Image size 100" or above, Aspect Ratio 16: 10, Inputs: HDMI, HDBaseT, VGA, Powered Zoom Lens & projector mountin bracket etc. complete with installation as per the site requirement. Approved Make: Panasonic / Barco / NEC

Projection Screen fixed type. Screen size 100 " in 16: 9 Aspect ratio with unity gain Approved Make: Dallite / Draper / Stewart

Scaller cum Automatic switcher High−performance presentation scaler/switcher for HDMI and VGA . The unit scales the video, embeds the audio, and outputs the signal to two HDMI (with embedded audio) outputs (with S/PDIF and balanced stereo audio) simultaneously with PixPerfect Scaling Technology precision pixel mapping and high−quality scaling technology. High−quality 3:2 and 2:2 pull down de−interlacing and full up and down scaling of all video input signals,Video Inputs - 10 HDMI & 2 VGA ,Scaled Outputs - 2 HDMI , 22 Output Resolutions - Up to WUXGA/1080p and Auto Input Scanning and Switching. Approved Make: Kramer / Lightware / Crestron / Extron / Wyrestrom

Wireless presentation system : Wireless Collaboration device for in−room meeting participant can present and view the main display, edit documents together in real time, share any size file, turn the main display into a digital whiteboard, and more.Should have e−polling feature for easily and instantly measure how much students & trainees are actually learning. Device can show up to six user screens on one main display or up to 12 screens on two displays. The solution features iOS mirroring for MacBook, iPad, iPhone, Windows phone, Chromebook and Android mirroring (Lollipop OS 5.0 or newer). Remote students can easily join the class and collaborate in real time with embedded 3rd−party video conferencing and office apps.Should be able to share uninterrupted HD video of 1080p @ 60Hz on HDMI Output withaudio de-mbedding feature.. It Should have in-built memory of 64GB (SSD). Approved Make: Kramer / AMX / Crestron / Wyrestrom / Extron

Passive Wall Plate : Active wall plate having connectivity port for HDMI, VGA, Audio and Ethernet and HDBaseT output on twisted pair format.Should support 4K@60Hz with chroma sampling of 4:2:0 and capable of carrying Ethernet & RS-232 as control signal.Should be capable of carrying Audio signal independently without any active VGA input at any given time. Should have a minimum data rate of 10 GBPS.Wall plate should be capable of managing Extended Display Information Data.Should have automatic Live input detection.Should be capable of re-building the signal so that it can travel upto longer distances-Up to 130m (430ft) at normal mode (2K), up to 100m at normal mode (4K).Should be compatible with HDTV and HDCP. Device should be capable of automatic Analog Audio Detection & Embedding. Approved Make: Kramer / Lightware / Crestron / Wyrestrom / Extron

UTP based HDMI Receiver: HDMI, Bidirectional RS−232 & IR over Twisted Pair Receiver; Input: 1 CAT 5; Output: 1 HDMI; Supports HDMI and HDCP. Approved Make: Kramer / Lightware / Crestron

HDMI Cable should be High Speed with Ethernet it should support Data Transfer rate of upto minimum 10GBps and upto 48 bit Deep Color. Connectors must have a minimal locking capability to prevent ousting of cables from ports. Should have an overall shield against EMI/RFI interference Should be CL2 flame tested. Approved Make: Kramer / Extron / Crestron

Wi Fi Router Approved Make: HP / Cisco / Netgear

FOR 3X500 SEATER ROOM PROJECTION SYSTEM SITC of 1-chip DLP LASER Phosphor Multimedia Projection system having, 10000 Lumens (center) 20000 hours lamp life, 1920 x 1200 WUXGA Native Resolution, 10000:1 Contrast Ratio, inputs: HDBaseT,HDMI, DVI-D, alongwith Powered Zoom Lens & projector mountin bracket etc. complete with installation as per the site requirement. Approved Make: Pansonic / Barco / NEC

Motorised Projection Screen with Unity Gain of size 147" (h) x 236" (w), 16:10 Aspect Ratio complete with Low Voltage control module, upto 2' of black drop as per site requirement Approved Make: Dallite / Draper / Stewart

Should have and support 4K UHD, HDBaseT active wall plate with step−in auto switcher for HDMI, VGA and analog audio signals and Output should be in twisted pair format that supports resolutions up to 4K@60Hz (4:2:0). The device has EDID management, easy control options and audio embedding. The unit is a fully−featured with the convenience and simplicity of a wall plate.It should be easy to install with browser−based configuration and single PoE cable for Ethernet connectivity and powering.it should be HDCP cmpliant and support Max. Data Rate - 10.2Gbps (3.4Gbps per graphic channel. Should support Range − Up to 70m in normal mode. Approved Make: Kramer / Lightware / Crestron / Extron / Wyrestrom

Distribution amplifier 1:4 for 4K@60Hz (4:2:0) HDMI 2.0 signals complying with the HDCP 1.4 content protection standard. The unit takes one HDMI input, equalizes and reclocks the signal and distributes it to four identical outputs.Should have Max. Data Rate — 10.2Gbps (3.4Gbps per graphic channel) and Should have 1 USB for firmware upgrade.Device Should have Compliance - HDMI 2.0, HDCP 1.4 and support deep color, x.v.Color, lip sync, 7.1 PCM, Dolby TrueHD, DTS–HD, CEC (OUT 1 only), 2K, 4K, and 3D. Device also have button for EDID setup and status indicators for HDMI input and output connected signals, and power indicator. Approved Make: Kramer / Lightware / Crestron / Extron / Wyrestrom

High−performance, extended−reach HDBaseT PoE transmitter for 4K60Hz (4:2:0) HDMI, Ethernet, RS−232 and IR signals over twisted pair.It converts. It extends video signals to up to 100m (330ft) over CAT copper cables at up to 4K@60Hz (4:2:0) 24bpp video resolution and provides even further reach for lower HD video .Should support a minimum data rate of 10Gbps.HDMI Signal Extension HDMI 2.0 and HDCP 2.2 compliant. Supports deep color, x.v.Color, lip sync, HDMI uncompressed audio channels, Dolby TrueHD, DTS–HD, 2K, 4K, and 3D. EDID and CEC signals are passed through from the source to the display.Multi–channel Audio Extension — Up to 32 channels of digital stereo uncompressed signals for supporting studio–grade surround sound.minimum data rate of 10Gbps Approved Make: Kramer / Lightware / Crestron / Extron / Wyrestrom

4K60 4:2:0 HDMI HDCP 2.2 PoE Receiver with Ethernet, RS–232 & IR over Extended–Reach HDBaseT,It extends video signals to up to 100m (330ft) over CAT copper cables at up to 4K@60Hz (4:2:0) 24bpp video resolution and provides even further reach for lower HD video resolutions.HDMI Signal Extension — HDMI 2.0 and HDCP 2.2 compliant. Supports deep color, x.v.Color, lip sync, HDMI uncompressed audio channels, Dolby TrueHD, DTS–HD, 2K, 4K, and 3D. EDID and CEC signals are passed through from the source to the display.I–EDIDPro-Intelligent EDID Processing — Intelligent EDID handling, processing and pass–through algorithm that ensures Plug and Play operation for HDMI source and display systems. Multi–channel Audio Extension — Up to 32 channels of digital stereo uncompressed signals for supporting studio–grade surround sound.minimum data rate of 10Gbps Approved Make: Kramer / Lightware / Crestron / Extron / Wyrestrom

Wireless collaboration and presentation solution that makes sharing and presenting in meetings easier. With any laptop or mobile device, users can view, edit and comment on documents in real time, share files and chat with individuals or multiple participants simultaneously. The solution can show up to four screens on the main display. and participant can view the main display, edit documents together in real time, share any size file, turn the main display into a digital whiteboard, and more. The solution features iOS mirroring for MacBook, iPad, iPhone, Windows phone and Android device connectivity wirelessly. Device having HDMI input and High quality video streaming, supports full HD 1080p/60Hz. device is capable to connect more than 200 device with secure 1024–bit encryption. device having 4 USB 3.0, 1 LAN on an RJ–45 connector, 1 HDMI Input and 1 HDMI, 1 mini DisplayPort and Audio output. Device having 4GB high Speed memory,4th generation Intel® Dual core 1.4GHz processor and 32GB, solid–state drive with Do not disturb (DND) feature that would enable uninterrupted presentation. Approved Make: Kramer / AMX / Crestron / Wyrestorm / Extron

Master/space controller with PoE with Minimum 4 bidirectional RS232, 4 IR, 4 Relays and 4 GP/IO and 1 Ethernet port to control all the devices in the room. Should have inbuilt IR sensor to learn IR commands .The compatible relay controller to control the Projector up down should be supplied as a package (may be from same OEM of controller or different). Should have inbuilt processing power and internal storage to store and process the control program. Should be compatible with any (IOS/Android) wireless or wired Touch screen of any size. Additional ports if required can be added with minimum hassle. Should have the flexibility to add as many user interfaces as required. Should have embedded webpage for control port settings.Should have Status LED to check for Control/Connection status.It should support PoE. Device Has 512MB RAM, 4GB Flash memory.It should have minimum 5 free license if required for iOS/Android application Approved Make: Kramer / AMX / Crestron / Wyrestorm / Extron

12−button control keypad, with knob and LCD displays with 12 RGB–color, backlit buttons. custom labeled removable button caps. with Digital knob for volume control.It should have 3 8–characters program–configurable LCD displaysand control processor in-built with 3 RS-232, 2 IR, 2 I/O & 4 relay ports. Device have IR learner in-built,1 mini USB connector for programming and work in sync with primary master room controller.Every button should be configurable and touch sensitive.Should be operable within the temperature range of 0 deg C to 40 deg C.Extra component or equipment maybe added to match the complete specs. Approved Make: Kramer / AMX / Crestron /Wyrestorm / Extron

3.5mm to Single IR Emitter Cable Approved Make: Kramer / AMX / Crestron / Wyrestorm / Extron

CAT6A U/FTP 4 shielded twisted pairs ,23AWG solid copper conductor Video & LAN Bulk Cable — Low Smoke & Halogen Free recommended by HDBaseT Approved Make: Kramer / Extron / Belden

Layer 2 Gigabit switch 8 port. Approved Make: HP / Cisco / Netgear

Network router standard quality to create WIFI Approved Make: HP / Cisco / Netgear

Cat6 Cable for Data . Approved Make: Belden / AMP / Punduit

High Speed triple-shielded bonded pairs HDMI Cable with Ethernet Gold Palted Lockable Connector. It support Data Transfer rate of upto minimum 10GBps and upto 48 bit Deep Color. Cable has overall shield against EMI/RFI interference and CL2 flame tested. Approved Make: Kramer / Extron / Crestron / Belden / Wyrestrom

High Speed triple-shielded bonded pairs HDMI Cable with Ethernet Gold Palted Lockable Connector. It support Data Transfer rate of upto minimum 10GBps and upto 48 bit Deep Color. Cable has overall shield against EMI/RFI interference and CL2 flame tested. Approved Make: Kramer / Extron / Crestron / Belden / Wyrestrom

FOR 3X500 SEATER ROOM AUDIO SYSTEM Supply, Installation, Testing and Commissioning of Active Steerable Columnar Array : Active Column Loudspeaker with onboard DSP, Thirty two (32) or more transducers with 130Hz-20kHz, AES/DANTE and line-level analog input connectivity, Articulated array configurations with 110-130 degrees horizontal and Vertical 10 - 100 degree Symmetrical or asymmetrical with single of multiple beams (no of modules to match the require angle) vertical coverage, +/- 40 degrees vertical Beam steering angles with application distance of minimum 40 - 50mtr. Max SPL 100dB at 30 meter. Internal / External Interface Module for comission the Digital Steerable Speaker Approved Make: Tannoy / Bose / Meyer Sound / Renkus-Heinz

Supply, Installation, testing and commissioning of Wall Mount full range loudspeaker with frequency range (-10dB) of 80Hz to 20kHz; RMS continuous power handling of 100W better; Nominal dispersion of 90 H X 60 V; full range Sensitivity of 90 Db SPL; Max SPL of 111 dB SPL (117dB peak); Nominal Impedance of 8 ohms; Rugged Birch Plywood enclosure with powder coated steel grille. Approved Make: Tannoy / Bose / Martin Audio / Renkus-Heinz

Wall Brackets Approved Make: Tannoy / Bose / Martin Audio / Renkus-Heinz

Supply, installation, testing & Commissioning of Compact Dual 12" or better Installation friendly subwoofer with Freq. Range of 35 Hz - 200Hz or better. It should have an axial Sensitivity of > = 99dB (1W/1m) or more delivering a Max. Calculated SPL(Continuous) of >=128 dB (134dB Peak). The loudspeaker should have a nominal impedance of 4ohm or better and continuous Power Handling of 750W (3000W Peak) or more. The Subwoofer shall be enclosed in Baltic birch plywood with polyurethene paintable grill. Approved Make: Tannoy / Bose / Martin Audio / Renkus-Heinz

Supply, installation, testing & Commissioning of 2 channel class D Networkable Power amplifier with a Max Output Power of 2x1200W@4 ohms, (in scenario of Muliple Channel Amplifier, need to match the reuire amplification power) shall give . 20Hz - 20 KHz, SNR of 104dB or better and THD + N of <0.1% with built in protection such as Limiters, Temperature, DC, Short Circuit, Peak Current Limiters, Turn on delay etc. Built in DSP for Matrix routing, Speaker equalization, Delays, Array EQs etc complete with Ethernet Port for Network Control, programming and monitoring. Approved Make: Labgruppen / Bose / Powersoft / Procella

Supply, installation, testing & Commissioning of 2 channel class D Networkable Power amplifier with a Max Output Power of 2x600W@4 ohms, (in scenario of Muliple Channel Amplifier, need to match the reuire amplification power) shall give . 20Hz - 20 KHz, SNR of 104dB or better and THD + N of <0.1% with built in protection such as Limiters, Temperature, DC, Short Circuit, Peak Current Limiters, Turn on delay etc. Built in DSP for Matrix routing, Speaker equalization, Delays, Array EQs etc complete with Ethernet Port for Network Control, programming and monitoring. Approved Make: Labgruppen / Bose / Powersoft / Procella

Supply of 40 channel Digital Mixing Console with 16 mic inputs, 25 bus, 6 Aux outs. Main LCR out and Matrix outputs, 40-Bit floating-point DSP, 24 bit ADC and DAC converters with minimum 112 dB dynamic range, minimum 17 motorised 100 mm faders, Optional wireless remote control for iPhone* and iPad* etc. 32 x 32 channel USB 2.0 audio interface, 8 DCA and 6 mute groups, Built in effect processor, Complete with Built in aur external 100-Band RTA for all Channel/Bus EQ 's, Auto-ranging universal switch-mode power supply. Digital Audio Port fo connectivity with Stage Box Approved Make: Behriger / Yamaha / Soundcraft

Supply, Installation, testing and commissioning of wireless digital Handheld Microphone with 18 or more channel, RF output 80mW or more, super cardiod pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital lavalier Microphone with 18 or more channel, RF output 80mW or more, omni directional pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital Headworn Microphone with 18 or more channel, RF output 80mW or more, omni directional pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital Gooseneck Microphone with 18 or more channel, RF output 80mW or more, Cardioid / super cardiod pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital Gooseneck Microphone charging charging pad can charge minimu 2no. Of microphone simulataneously and operate on network Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital Hadheld , Lapel & Headworn Microphone charging docking station can charge minimu 4no. Of microphone simulataneously and operate on network Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of shotgun microphone, pollar pattern : super-cardioid / lobar / array, Frequency response : 40 Hz to 20 kHz , Min. terminating impedance : 1 kΩ , Equivalent noise level : 23 dB(A) , Acoustics : interference tube transducer, gooseneck length : 180mm or less Approved Make: Sennheiser / Shure / Beyerdynamic

Vocal Handheld wired microphone. Approved Make: Sennheiser / Shure / Beyerdynamic

Heavy duty 2 core 2.5 sqmm copper loudspeaker cable. Approved Make: Sommer / Gotham / Canare

Heavy duty 2 core shielded microphone cable, 22AWG Approved Make: Sommer / Gotham / Canare

Making of Mike/speaker points on stage Approved Make: Custom / Apprv Eqv

Table stand Approved Make: K&M / Beyerdynamic / Sennhiser

Floor Stand Approved Make: K&M / Beyerdynamic / Sennhiser

19 "Equipment Rack Made of MS for housing of all above equipment , front lockable acrylic door, Fan for colling, Caster wheel base , Complete with MCB including all internal wiring/ interconnection as required. Approved Make: Valrack / Rittal / President

FOR 900 SEATER ROOM AUDIO SYSTEM Supply, Installation, Testing and Commissioning of Active Steerable Columnar Array : Active Column Loudspeaker with onboard DSP, Forty Eight (48) or more transducers with 110Hz-20kHz, AES/DANTE and line-level analog input connectivity, Articulated array configurations with 110-130 degrees horizontal and Vertical 10 - 100 degree Symmetrical or asymmetrical with single of multiple beams (no of modules to match the require angle) vertical coverage, +/- 40 degrees vertical Beam steering angles with application distance of minimum 35 - 40mtr. Max SPL 101.5dB at 30 meter or more. Internal / External Interface Module for comission the Digital Steerable Speaker Approved Make: Tannoy / Bose / Meyer Sound / Renkus-Heinz

Supply, installation, testing & Commissioning of Compact Dual 12" or better Installation friendly subwoofer with Freq. Range of 35 Hz - 200Hz or better. It should have an axial Sensitivity of > = 99dB (1W/1m) or more delivering a Max. Calculated SPL(Continuous) of >=128 dB (134dB Peak). The loudspeaker should have a nominal impedance of 4ohm or better and continuous Power Handling of 750W (3000W Peak) or more. The Subwoofer shall be enclosed in Baltic birch plywood with polyurethene paintable grill. Approved Make: Tannoy / Bose / Martin Audio / Renkus-Heinz

Supply, Installation, testing and commissioning of Wall Mount full range loudspeaker with frequency range (-10dB) of 80Hz to 20kHz; RMS continuous power handling of 100W better; Nominal dispersion of 90 H X 60 V; full range Sensitivity of 90 Db SPL; Max SPL of 111 dB SPL (117dB peak); Nominal Impedance of 8 ohms; Rugged Birch Plywood enclosure with powder coated steel grille. Approved Make: Tannoy / Bose / Martin Audio / Renkus-Heinz

Wall Brackets Approved Make: Tannoy / Bose / Martin Audio / Renkus-Heinz

Supply, Installation, testing and commissioning of Multipurpose Speaker with Frequency Response of 60 Hz to 20 kHz or better ; Horizontal Nominal Dispersion : 90 degree Horizontal X 60 degree Vertical or better (Rotatable Horn); Sensitivity (SPL / 1 W @ 1 m) of 96 dB SPL or beter. Continuous Power of 200 Watt or better; Impedance of 8 Ohm ; Max SPL @ 1 Mtr (Cont.) of 120 dB SPL or better ; Transducers/Drivers of HF: 1 x 1" or better; LF: 1 X 12" or better complete with standard accessories Approved Make: Tannoy / Bose / Martin Audio / Renkus-Heinz

Supply , installation , testing and commissioning of Compact Indoor type wall mount Music Loudspeaker:Frequency range (-10dB) of 70Hz to 20kHz; Power handling of 150 Watt peak; Nominal dispersion of 110-120 H X 110-120V; Sensitivity of 84 dB SPL and Max SPL of 105 dB SPL peak; Nominal Impedance 8 Ohms; Integral multi-tap Transformer with tap settings of 4/8/15/30 W @ 70V/100V. with Powder-coated steel grille; Brackets with pitch/yaw adjustment included. With wall mount brcaket Approved Make: Tannoy / Bose / Martin Audio / Renkus-Heinz

Volume Controller Approved Make: Apart Audio / Lowell / Bosch

Supply, installation, testing & Commissioning of 2 channel class D Networkable Power amplifier with a Max Output Power of 2x1200W@4 ohms, (in scenario of Muliple Channel Amplifier, need to match the reuire amplification power) shall give . 20Hz - 20 KHz, SNR of 104dB or better and THD + N of <0.1% with built in protection such as Limiters, Temperature, DC, Short Circuit, Peak Current Limiters, Turn on delay etc. Built in DSP for Matrix routing, Speaker equalization, Delays, Array EQs etc complete with Ethernet Port for Network Control, programming and monitoring. Approved Make: Labgruppen / Bose / Powersoft / Procella

Supply, installation, testing & Commissioning of 2 channel class D Networkable Power amplifier with a Max Output Power of 2x6000W@4 ohms, (in scenario of Muliple Channel Amplifier, need to match the reuire amplification power) shall give . 20Hz - 20 KHz, SNR of 104dB or better and THD + N of <0.1% with built in protection such as Limiters, Temperature, DC, Short Circuit, Peak Current Limiters, Turn on delay etc. Built in DSP for Matrix routing, Speaker equalization, Delays, Array EQs etc complete with Ethernet Port for Network Control, programming and monitoring. Approved Make: Labgruppen / Bose / Powersoft / Procella

Supply, installation, testing & Commissioning of 2 channel class D Energy Star Compliant Power amplifier with a Max Output Power of 2x120W@8 / 4 ohms, 20Hz - 20 KHz, SNR of 100dB or better and THD + N of <0.3% with built in GPIO Port & Speaker Preset. Approved Make: Labgruppen / Bose / Powersoft / Extron

Supply of 40 simultaneous input channels min 32 Input Channels, 8 Aux Channels, 8 FX Return Channels min 16 Output Processing Channels 32 microphone preamplifiers 16 Internal Effects Engines (True Stereo / Mono) 25 time-aligned and phase-coherent mix buses AES50 networking 32 x 32 channel USB 2.0 audio interface MIDI Inputs / Outputs, Digital Link Expansion Port,Channel Expansion Card Interface 8 DCA and 6 mute groups,8 stereo signal processing effects engines Open architecture allows for future 96 kHz operation 192 kHz ADC and DAC converters,40 bit floating point digital signal processing, Daylight viewable 7” full colour TFT display screen +48 V Phantom Power (Switchable per Input) min 25 motorised 100 mm faders, Built-in RTA for all channel Remote Controllable, Auto-ranging universal switch-mode power supply etc. all complete. Digital mixer should be suppleid with 32 inputs and 16 output stage Box, etc complete with installation Approved Make: Behringer / Yamaha / Soundcraft

Supply, Installation, testing and commissioning of wireless digital Handheld Microphone with 18 or more channel, RF output 80mW or more, super cardiod pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital lavalier Microphone with 18 or more channel, RF output 80mW or more, omni directional pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital Headworn Microphone with 18 or more channel, RF output 80mW or more, omni directional pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital Gooseneck Microphone with 18 or more channel, RF output 80mW or more, Cardioid / super cardiod pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital Gooseneck Microphone charging charging pad can charge minimu 2no. Of microphone simulataneously and operate on network Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital Hadheld , Lapel & Headworn Microphone charging docking station can charge minimu 4no. Of microphone simulataneously and operate on network Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of shotgun microphone, pollar pattern : super-cardioid / lobar / array, Frequency response : 40 Hz to 20 kHz , Min. terminating impedance : 1 kΩ , Equivalent noise level : 23 dB(A) , Acoustics : interference tube transducer, gooseneck length : 180mm or less Approved Make: Sennheiser / Shure / Beyerdynamic

Vocal Handheld wired microphone. Approved Make: Sennheiser / Shure / Beyerdynamic

Heavy duty 2 core 4 sqmm copper loudspeaker cable. Approved Make: Sommer / Belden / Canare

Heavy duty 2 core shielded microphone cable, 22 AWG Approved Make: Sommer / Belden / Canare

Making of Mike/speaker points on stage Approved Make: Custom / Apprv Eqv

Table stand Approved Make: K&M / Beyerdynamic / Sennhiser

Floor Stand Approved Make: K&M / Beyerdynamic / Sennhiser

19 "Equipment Rack Made of MS for housing of all above equipment , front lockable acrylic door, Fan for colling, Caster wheel base , Complete with MCB including all internal wiring/ interconnection as required Approved Make: Valrack / Rittal / President

FOR 900 SEATER ROOM PROJECTION SYSTEM Supply, Installation, Testing and Commissioning of Projector 3 chip DLP, 1920X1200 native solution, min. 20,000 lumens, laser phosphor projector with minimum 20000 hours light shouce, Contrast Ratio : 10000 : 1, Motorized horizontal and vertical lens offset , Inputs: HDBaseT,HDMI, DVI-D Controls: RS232 and Ethernet should be complete with mounts and lens. Approved Make: Panasonic / Barco / NEC

Motorised Tab Tensioned Projection Screen with Unity Gain of size 177" (h) x 284" (w), 16:10 Aspect Ratio complete with Low Voltage control module as per site requirement Approved Make: Dallite / Draper / Stewart

Should have and support 4K UHD, HDBaseT active wall plate with step−in auto switcher for HDMI, VGA and analog audio signals and Output should be in twisted pair format that supports resolutions up to 4K@60Hz (4:2:0). The device has EDID management, easy control options and audio embedding. The unit is a fully−featured with the convenience and simplicity of a wall plate.It should be easy to install with browser−based configuration and single PoE cable for Ethernet connectivity and powering.it should be HDCP cmpliant and support Max. Data Rate - 10.2Gbps (3.4Gbps per graphic channel. Should support Range − Up to 70m in normal mode. Approved Make: Kramer / Lightware / Crestron / Wyrestorm / Extron

Distribution amplifier 1:4 for 4K@60Hz (4:2:0) HDMI 2.0 signals complying with the HDCP 1.4 content protection standard. The unit takes one HDMI input, equalizes and reclocks the signal and distributes it to four identical outputs.Should have Max. Data Rate — 10.2Gbps (3.4Gbps per graphic channel) and Should have 1 USB for firmware upgrade.Device Should have Compliance - HDMI 2.0, HDCP 1.4 and support deep color, x.v.Color, lip sync, 7.1 PCM, Dolby TrueHD, DTS–HD, CEC (OUT 1 only), 2K, 4K, and 3D. Device also have button for EDID setup and status indicators for HDMI input and output connected signals, and power indicator. Approved Make: Kramer / Lightware / Crestron / Wyrestorm / Extron

High−performance, extended−reach HDBaseT PoE transmitter for 4K60Hz (4:2:0) HDMI, Ethernet, RS−232 and IR signals over twisted pair.It converts. It extends video signals to up to 100m (330ft) over CAT copper cables at up to 4K@60Hz (4:2:0) 24bpp video resolution and provides even further reach for lower HD video .Should support a minimum data rate of 10Gbps.HDMI Signal Extension HDMI 2.0 and HDCP 2.2 compliant. Supports deep color, x.v.Color, lip sync, HDMI uncompressed audio channels, Dolby TrueHD, DTS–HD, 2K, 4K, and 3D. EDID and CEC signals are passed through from the source to the display.Multi–channel Audio Extension — Up to 32 channels of digital stereo uncompressed signals for supporting studio–grade surround sound.minimum data rate of 10Gbps Approved Make: Kramer / Lightware / Crestron / Wyrestorm / Extron

4K60 4:2:0 HDMI HDCP 2.2 PoE Receiver with Ethernet, RS–232 & IR over Extended–Reach HDBaseT,It extends video signals to up to 100m (330ft) over CAT copper cables at up to 4K@60Hz (4:2:0) 24bpp video resolution and provides even further reach for lower HD video resolutions.HDMI Signal Extension — HDMI 2.0 and HDCP 2.2 compliant. Supports deep color, x.v.Color, lip sync, HDMI uncompressed audio channels, Dolby TrueHD, DTS–HD, 2K, 4K, and 3D. EDID and CEC signals are passed through from the source to the display.I–EDIDPro-Intelligent EDID Processing — Intelligent EDID handling, processing and pass–through algorithm that ensures Plug and Play operation for HDMI source and display systems. Multi–channel Audio Extension — Up to 32 channels of digital stereo uncompressed signals for supporting studio–grade surround sound.minimum data rate of 10Gbps Approved Make: Kramer / Lightware / Crestron / Wyrestorm / Extron

Wireless collaboration and presentation solution that makes sharing and presenting in meetings easier. With any laptop or mobile device, users can view, edit and comment on documents in real time, share files and chat with individuals or multiple participants simultaneously. The solution can show up to four screens on the main display. and participant can view the main display, edit documents together in real time, share any size file, turn the main display into a digital whiteboard, and more. The solution features iOS mirroring for MacBook, iPad, iPhone, Windows phone and Android device connectivity wirelessly. Device having HDMI input and High quality video streaming, supports full HD 1080p/60Hz. device is capable to connect more than 200 device with secure 1024–bit encryption. device having 4 USB 3.0, 1 LAN on an RJ–45 connector, 1 HDMI Input and 1 HDMI, 1 mini DisplayPort and Audio output. Device having 4GB high Speed memory,4th generation Intel® Dual core 1.4GHz processor and 32GB, solid–state drive with Do not disturb (DND) feature that would enable uninterrupted presentation. Approved Make: Kramer / AMX / Crestron / Wyrestrom / Extron

Master/space controller with PoE with Minimum 4 bidirectional RS232, 4 IR, 4 Relays and 4 GP/IO and 1 Ethernet port to control all the devices in the room. Should have inbuilt IR sensor to learn IR commands .The compatible relay controller to control the Projector up down should be supplied as a package (may be from same OEM of controller or different). Should have inbuilt processing power and internal storage to store and process the control program. Should be compatible with any (IOS/Android) wireless or wired Touch screen of any size. Additional ports if required can be added with minimum hassle. Should have the flexibility to add as many user interfaces as required. Should have embedded webpage for control port settings.Should have Status LED to check for Control/Connection status.It should support PoE. Device Has 512MB RAM, 4GB Flash memory.It should have minimum 5 free license if required for iOS/Android application Approved Make: Kramer / AMX / Crestron /Wyrestrom / Extron

12−button control keypad, with knob and LCD displays with 12 RGB–color, backlit buttons. custom labeled removable button caps. with Digital knob for volume control.It should have 3 8–characters program–configurable LCD displaysand control processor in-built with 3 RS-232, 2 IR, 2 I/O & 4 relay ports. Device have IR learner in-built,1 mini USB connector for programming and work in sync with primary master room controller.Every button should be configurable and touch sensitive.Should be operable within the temperature range of 0 deg C to 40 deg C.Extra component or equipment maybe added to match the complete specs. Approved Make: Kramer / AMX / Crestron / Wyrestrom / Extron

3.5mm to Single IR Emitter Cable Approved Make: Kramer / AMX / Crestron

CAT6A U/FTP 4 shielded twisted pairs ,23AWG solid copper conductor Video & LAN Bulk Cable — Low Smoke & Halogen Free recommended by HDBaseT Approved Make: Kramer / Extron / Crestron

Layer 2 Gigabit switch 8 port. Approved Make: HP / Cisco / Netgear

Network router standard quality to create WIFI Approved Make:HP / Cisco / Netgear

Cat6 Cable for Data . Approved Make: Belden / Amp / Punduit

High Speed triple-shielded bonded pairs HDMI Cable with Ethernet Gold Palted Lockable Connector. It support Data Transfer rate of upto minimum 10GBps and upto 48 bit Deep Color. Cable has overall shield against EMI/RFI interference and CL2 flame tested. Approved Make: Kramer / Extron / Crestron / Wyrestrom / Belden

High Speed triple-shielded bonded pairs HDMI Cable with Ethernet Gold Palted Lockable Connector. It support Data Transfer rate of upto minimum 10GBps and upto 48 bit Deep Color. Cable has overall shield against EMI/RFI interference and CL2 flame tested. Approved Make: Kramer / Extron / Crestron / Wyrestrom / Belden

FOR 80 SEATER ROOM AUDIO SYSTEM Supply, Installation, Tetsing & Commissoning of Wireless Table Top Digital Chairman Unit with super cardiod / array Microphone, Goosneck length minimum 400mm or better, unit should have inbuilt Dual / Two way Loudspeaker for better sound reinforcement, Microphone on/off button, Priority switch for temporary muting delegates,20hr or more battery backup, frequency response : 100Hz to 16KHz, Audio quality : 16bit or better, built in headphone socket complete as per specification. Approved Make: Sennheiser / Shure / Beyerdynamic / Bosch

Supply, Installation, Tetsing & Commissoning of wireless Table Top Digital Delegate Unit with Super cardiod / array Microphone, Goosneck length minimum 400mm or better, unit should have inbuilt Twin / Two way Loudspeaker for better sound reinforcement, Microphone on/off button, ,20hr or more battery backup, frequency response : 100Hz to 16KHz, Audio quality : 16bit, built in headphone socket or better complete as per specification. Approved Make: Sennheiser / Shure / Beyerdynamic / Bosch

Supply, Installation, Tetsing & Commissoning of Digital Audio Conference Control Unit with antenna modeule for conference system supplies Power for minimum for 40 units and controls up to Miniumum 100 discussion units, RF output power : 100mW, Frequncy range: 5.1 - 5.9GHz, Coverage area : 30m or more, encryption : 128bit or more, built in / External USB Audio Recorder . An Ethernet Port shall be provided for network connection and control units, Integrated / external PC with 22 inch Full HD LED monitor, pre-installed control software for Microphone management, synoptic and Audio Recording, can be controllable wired and wireless discussion system etc and as per attached specification. Approved Make: Sennheiser / Shure / Beyerdynamic / Bosch

Charging Case for Chairman or delegate. Chargin time 4hr or less Approved Make: Sennheiser / Shure / Beyerdynamic / Bosch

Supply, Installation, Testing and Commissioning of Passive Column Array FOH Loudspeaker with minimum 5 drivers with frequency range: 130Hz-15kHz, Nominal Dispersion: 120degree H, Senstivity: 89dB, Max SPL 110dB SPL (116dB Peak), Power handling: 120W (480W Peak), Multiple Driver, Imp: 8 Ohms or better, Transformer Tap 100W/50W/25W @ 70V/100V with included accessories for mounting Approved Make: Tannoy / Bose / D&B Audio Teknik / Renkus-Heinz

Supply , installation , testing and commissioning of Ceiling Flush Music/PA Loudspeaker: Frequency range (-10dB) of 80Hz to 20kHz; Power handling of 120 Watt peak; Nominal dispersion of 90-100 Conical; Sensitivity of 86 dB SPL and Max SPL of 109 dB SPL peak; Nominal Impedance 6 Ohms or better; Integral multi-tap Transformer with tap settings of 3.75/7.5/15/30 W @ 70V/100V. with Powder-coated steel grille; Shall include necessary standard hardware for ceiling install. Approved Make: Tannoy / Bose / Martin Audio

Supply, installation, testing & Commissioning of 2 channel class D Energy Star Compliant Power amplifier with a Max Output Power of 2x400W@8 / 4 ohms/70Volt, 20Hz - 20 KHz, SNR of 110dB or better and THD + N of <0.1% complete with accessory Approved Make: Labgruppen / Bose / Powersoft

Supply, installation, testing & Commissioning of 2 channel class D Energy Star Compliant Power amplifier with a Max Output Power of 2x100W@8 / 4 ohms/70 Volt, 20Hz - 20 KHz, SNR of 110dB or better and THD + N of <0.1% complete with accessory Approved Make: Labgruppen / Bose / Powersoft

Supply, Installation, testing and commissioning of wireless digital Handheld Microphone with 18 or more channel, RF output 80mW or more, super cardiod pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital lavalier Microphone with 18 or more channel, RF output 80mW or more, omni directional pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, Battery back up : 16hr more, Battery capability : rechargable by dock station and mini / micro USB Approved Make: Sennheiser / Shure / Beyerdynamic

Supply, Installation, testing and commissioning of wireless digital Hadheld , Lapel & Headworn Microphone charging docking station can charge minimu 4no. Of microphone simulataneously and operate on network Approved Make: Sennheiser / Shure / Beyerdynamic

Heavy duty 2 core 2.5 sqmm copper loudspeaker cable. Approved Make: Sommer / Belden / Canare

Heavy duty 2 core shielded microphone cable, 22AWG Approved Make: Sommer / Belden / Canare

19 "Equipment Rack Made of MS for housing of all above equipment , front lockable acrylic door, Fan for colling, Caster wheel base , Complete with MCB including all internal wiring/ interconnection as required Approved Make: Valrack / Rittal / President / Netrack

FOR 80 SEATER ROOM PROJECTION SYSTEM Projector: 1-chip DLP Solid state(Laser Phosphor) Projection system with ultra short throw lens having 6000 Lumens, 1920 x 1200 Native Resolution, 10000:1 Contrast Ratio, Lamp Life 20000 hours, Min Image size 100" or above, Aspect Ratio 16: 10, Inputs: HDMI, HDBaseT, VGA, Powered Zoom Lens & projector mountin bracket etc. complete with installation as per the site requirement. Approved Make: Panasonic / Barco / NEC

Projection Screen fixed type. Screen size 120 " diagonal or better in 16: 9 Aspect ratio. Approved Make: Dallite / Draper / Stewart

Scaller cum Automatic switcher High−performance presentation scaler/switcher for HDMI and VGA . The unit scales the video, embeds the audio, and outputs the signal to two HDMI (with embedded audio) outputs (with S/PDIF and balanced stereo audio) simultaneously with PixPerfect Scaling Technology precision pixel mapping and high−quality scaling technology. High−quality 3:2 and 2:2 pull down de−interlacing and full up and down scaling of all video input signals,Video Inputs - 10 HDMI & 2 VGA ,Scaled Outputs - 2 HDMI , 22 Output Resolutions - Up to WUXGA/1080p and Auto Input Scanning and Switching. Approved Make: Kramer / Lightware / Crestron / Wyrestrom / Extron

Wireless presentation system : Wireless Collaboration device for in−room meeting participant can present and view the main display, edit documents together in real time, share any size file, turn the main display into a digital whiteboard, and more.Should have e−polling feature for easily and instantly measure how much students & trainees are actually learning. Device can show up to six user screens on one main display or up to 12 screens on two displays. The solution features iOS mirroring for MacBook, iPad, iPhone, Windows phone, Chromebook and Android mirroring (Lollipop OS 5.0 or newer). Remote students can easily join the class and collaborate in real time with embedded 3rd−party video conferencing and office apps.Should be able to share uninterrupted HD video of 1080p @ 60Hz on HDMI Output withaudio de-mbedding feature.. It Should have in-built memory of 64GB (SSD). Approved Make: Kramer / AMX / Crestron / Wyrestrom / Extron

Passive Wall Plate : Active wall plate having connectivity port for HDMI, VGA, Audio and Ethernet and HDBaseT output on twisted pair format.Should support 4K@60Hz with chroma sampling of 4:2:0 and capable of carrying Ethernet & RS-232 as control signal.Should be capable of carrying Audio signal independently without any active VGA input at any given time. Should have a minimum data rate of 10 GBPS.Wall plate should be capable of managing Extended Display Information Data.Should have automatic Live input detection.Should be capable of re-building the signal so that it can travel upto longer distances-Up to 130m (430ft) at normal mode (2K), up to 100m at normal mode (4K).Should be compatible with HDTV and HDCP. Device should be capable of automatic Analog Audio Detection & Embedding. Approved Make: Kramer / Lightware / Crestron / Wyrestrom / Extron

UTP based HDMI Receiver: HDMI, Bidirectional RS−232 & IR over Twisted Pair Receiver; Input: 1 CAT 5; Output: 1 HDMI; Supports HDMI and HDCP. Approved Make: Kramer / Lightware / Crestron / Extron / Wyrestorm

HDMI Cable should be High Speed with Ethernet it should support Data Transfer rate of upto minimum 10GBps and upto 48 bit Deep Color. Connectors must have a minimal locking capability to prevent ousting of cables from ports. Should have an overall shield against EMI/RFI interference Should be CL2 flame tested. Approved Make: Kramer / Extron / Crestron / / Extron / Wyrestorm

Wi Fi Router Approved Make: HP / Cisco / Netgear

FOR 900 SEATER ROOM CAMERA SYSTEM High performance Full HD PTZ camera with Integrated Pan-Tilt Provides Video Output via 3G-SDI or IP Streaming Transmission for an Expanded Range of Applications Introducing a new PTZ camera capable Production Quality Full HD video output up to 1080/60p via IP transmission, in addition to 3G-SDI and HDMI. Equipped with three newly developed 1/2.86 MOS sensors for high sensitivity, a superior S/N ratio and high resolution, also supports PoE+*, so the camera only needs one LAN cable for its power supply, control and video output. Standard in versatile, high-quality remote production with 3G-SDI, IP-Streaming, and POE+.Dynamic Range Stretch (DRS) / Hybrid Digital Noise Reduction (Hybrid DNR) Equipped with Night Mode for infrared shooting, High Performance 20x Zoom Lens/1.4x Digital Extender Zoom, Optical Image Stabilization System (OIS), Equipped with ND filters (Through, 1/8, 1/64), Preset memory of up to 100 positions, Functions such as freeze during preset, digital extender zoom, color temperature settings can be assigned to the user buttons on Equipped with RS422 remote terminal can be controlled via serial control from a controller. Equipped with RS232C remote terminal (Standard serial communication support). Approved Make: Sony / Panasonic / Vaddio / Blackmagc Design

Camera controller Remote PTZ Camera System Controller with IP and Serial Connectivity of power supply DC12 V/0.5 A (DC input range:DC10V to DC16V), In IP connection Upto 100 remote cameras can be controlled, Serial Control compatibility for Upto 5 remote cameras can be controlled, Preset Memory upto 100 camera angle settings, Camera Image Quality Adjustment with AWB,ABB,pedestal and gain adjustment, its control panel features a large pan/tilt joystick; seesaw zoom lever; iris dial; and manual focus dial with One-Touch Autofocus. A dedicated speed adjustment dial is provided for each of the pan/tilt/zoom and focus functions. Precise camera moves and scene operations can be memorized and recalled via the unit's Tracing Memory. Up to 10 Tracing Memory script items can be stored for each camera. In addition; up to 100 standard presets; including pan; tilt; zoom position; focus; iris and white balance settings; can be quickly stored and recalled for each camera, Its LCD panel facilitates menu operation as well as dedicated zoom; focus and iris indicator display. Various functions can also be allocated to eight User Buttons for one-touch control. Approved Make: Sony / Panasonic / Vaddio / Blackmagc Design

AV production switcher HD/SD multi format live switcher with Nine Standard Inputs: Eight SDI and One DVI and Six Standard Outputs: Five SDI and One DVI, Built-in 178 mm ( 7 inches) multi-mode color LCD monitor displays versatile menus, image monitor, waveform/vectorscope, Featuring High-quality Primatte chroma keying and Versatile transitions, including DVE functions,Enhanced MultiViewer Display with up to 16 splits enables nine screen variations, clock, level meter and 4:3 marker display, Video Memory function allows playback of two channels of still or moving images, Memory Preview function provides previews of shot memory and event memory image effects, Supports Plug-in API function for external control, external camera control, output of status data, Control panel with additional direct button control, numeric keypad, etc achieves enhanced ease of operation Make: Sony / Panasonic / Vaddio / Blackmagic Design

Portable P2 Memory Card Recorder compact, lightweight field recorder and deck that supports the AVC-ULTRA family of codecs. It records up to 1080p 59.94/50 video to microP2 and P2 memory cards, and features HDMI, 3G-SDI, and analog inputs/outputs for connecting to a wide range of video and audio devices having high-speed USB 3.0 (Host) interface for transferring and backing up files to an external storage device and previewing externally stored files. The recorder also provides a standard RJ-45 Ethernet port for wired connection to a LAN for remote control and transferring files to a network. The recorder has three memory card slots; two for microP2 cards, and one for full-sized P2 cards. Make: Sony / Panasonic / Vaddio / Blackmagic Design

H.264 Streaming Media Processor, Process two high resolution AV sources from up to five available input signals, Stream and record simultaneously, High quality scaling with flexible two-window management, Produces MP4 media files that are compatible with virtually any media player, Dual Recording and Streaming with LinkLicense. Input: Number/signal type 3 HDMI digital video (HDCP compliant), 1 component video (Y, R-Y, B-Y; interlaced, progressive, HD), or composite video, Nominal level 1 Vp-p for Y of component video and for composite video, Minimum/maximum level Analog: 0.0 V to 1.0 Vp-p with no offset, Horizontal frequency 15 kHz to 100 kHz, Vertical frequency 24 Hz to 75 Hz ,Resolution range 640x480 to 1920x1200 (reduced blanking), 480p, 480i, 576p, 720p, 1080i, 1080p, NTSC, and PAL, sampled pixel for pixel. Video output: SMP 351, SMP 351 3G-SDI 2 H.264/AVC digital video over Ethernet, 1 HDMI digital video (HDCP compliant).The unit has built in 80 GB SSD memory for internal recording. Make: Sony / Panasonic / Vaddio / Blackmagic Design

Network Switch Approved Make: HP / Cisco / Netgear

HDMI Cable :High Speed with Ethernet HDMI Cable. Should support Data Transfer rate of upto minimum 10GBps and upto 48 bit Deep Color. Connectors must have a minimal locking capability to prevent ousting of cables from ports. Should have an overall shield against EMI/RFI interference Should be CL2 flame tested. Approved Make: Kramer / Extron / Crestron / Belden / Wyrestrom

Shielded U/FTP of 23 AWG solid copper conductor 4 shielded Twisted pair cable, low smoke halogen free. Approved Make: Kramer / Extron / Crestron

HD SDI to single mode fiber on LC connector 3G HD-SDI Tx. High performance fiber optic transmitter for SDI video signals up to 3G HD−SDI,it supports 2 x 3G SDI input & give single mode/Multimode fiber output and has a minimum data rate of 3 Gbps, the unit is capable to carry high quality signal upto a distance of 10km , it is HDTV compatible, it also supports multi-standard operation – SDI (SMPTE 259M and SMPTE 344M), HD–SDI (SMPTE 292M), 3G HD–SDI (SMPTE 424M) and is capable to receive signal from the below fiber optic receiver Approved Make: Kramer / Extron / Crestron / Wyrestorm

Single mode fiber to on LC connector 3G HD-SDI Rx. High performance fiber optic reciever for SDI video signals up to 3G HD−SDI,it supports 2 x 3G SDI input & give single mode/Multimode fiber output and has a minimum data rate of 3 Gbps, the unit is capable to carry high quality signal upto a distance of 10km , it is HDTV compatible, it also supports multi-standard operation – SDI (SMPTE 259M and SMPTE 344M), HD–SDI (SMPTE 292M), 3G HD–SDI (SMPTE 424M) and is capable to receive signal from the above fiber optic transmitter Approved Make: Kramer / Extron / Crestron / Wyrestorm

LIU & other accessories like rack & pig tails

4K SDI Distribution Amplifier . One input Eight output SDI distribution amplifier it supports upto 4K at 12GBPS resolution and is able to Re-Build and Re-Clock the video signal on output for 80Meter for 12GBPS signal. It complies with SMPTE 259M (SD–SDI), 292M (HD–SDI), 344M (ED–SDI), 424M (3G HD–SDI), ST–2081 (6G–SDI) and ST–2082 (12G–SDI) standards. Approved Make: Kramer / Extron / Crestron / Wyrestrorm

Display unit, 32" digaonal, 350 nits, 720p or better, HDMIApproved Make: Panasonic / Samsung / Chrisitie

Armoured Single mode Fiber Optic cable from Main mandap to parking bay of OB van

SUBSTATION WORK- 1250 KVA RADIATOR COOLED D.G. SET Supplying, including installation. Testing and commissioning of water cooled jackson Diesel Generator set coupled to suitable alternator of 415 V, AC, 3-Phase 0.8 p.f. mounted on a 1) M.S. fabricated base frame., 2) M.S. fuel tank of required capacity., 3) Residual Silencer., 4) AMF/Standard Control Panel. 5) Suitable batteries with lead., 6) First fill of Lube oil., 7) Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to IS comprising the following Technical Specification. GENERATOR SET SPECIFICATIONS 1250/1000 No. of Phases- 3 Phase POWER FACTOR-0.8 LAG JACKSON ENGINE SPECIFICATIONS 1. Make- Cummins 2. Model- KTA-50-G3 with PCC-3.3 3. No. of Cylinders-16 4.Aspirations- TURBO CHARGED after COOLED 5.Cooling- Water Cooled 6.Governor-Electronic 7. Battery Capacity Rating-4X12 Volt 8.FUEL CONSUMPTION LTR?HR @ 75% LOAD 190.8 ALTERNATOR SPECIFICATIONS 1. Make- STAMFORD 2. Voltage Regulation : +/- 1.0% 3. Insulation : Class-H 4. Standard Enclosure : IP 23 5. No. of Phases-3 D.G. Set described as above

DIESEL GENERATOR Supplying, including installation. Testing and commissioning of water cooled jackson Diesel Generator set coupled to suitable alternator of 415 V, AC, 3-Phase 0.8 p.f. mounted on a 1) M.S. fabricated base frame., 2) M.S. fuel tank of required capacity., 3) Residual Silencer., 4) AMF/Standard Control Panel. 5) Suitable batteries with lead. 6) First fill of Lube oil. 7) Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to IS comprising the following Technical Specification. GENERATOR SET SPECIFICATIONS 625/500 No. of Phases- 3 Phase POWER FACTOR-0.8 LAG JACKSON ENGINE SPECIFICATIONS 1. Make- Cummins 2. Model- VTA-28-G5-1 with PCC-3.3 3. No. of Cylinders-12 4.Aspirations- TURBO CHARGED after COOLED 5.Cooling- Water Cooled 6.Governor-Electronic 7. Battery Capacity Rating-2X12 Volt 8.FUEL CONSUMPTION LTR?HR @ 75% LOAD 98.6 ALTERNATOR SPECIFICATIONS 1. Make- CGT (STAMFOR) 2. Voltage Regulation : +/- 1.0% 3. Insulation : Class-H 4. Standard Enclosure : IP 23 5. No. of Phases-3 WITH STANDARD CONTROL PANEL

EXHAUST PIPING Supply, Installation, Testing and Commissioning of following sizes MS exhaust piping heavy duty conforming to IS:3589 complete with all accessories such as bends, flanges, stainless steel flexible bellows etc. as required. 350 mm dia MS pipe. (5.0 mm thick)

300 mm dia MS pipe. (5.0 mm thick)

250 mm dia MS pipe. (5.0 mm thick)

Providing & Fixing of Insulation and cladding for exhaust piping using 75 mm thick rockool of density 150 Kg/ M3 & 24 SWG Aluminium Sheet.

Fabrication, supply & erection of MS structure for supporting of DG emission, exhaust piping with RCC foundation etc. complete in all respect.

INCOMMING / OUTGOING / BUSCOUPLER AIR CIRCUIT BREAKER: Supplying with fitting and fixing panel mounting open execution 4 pole Air Circuit Breaker type (MDO/EDO) with guide frame and 4 standard auxillary contacts in the existing cubical panel board of the following capacity complete with making necessary connection as specified and directed by the Dept. (ABB Emax/L & T U Power/ Siemens 3 WL/ Schneider Master pact NW) 6A trip system. 1000A Breaking capacity @ Ics=50 KA (EDO)

2000A Breaking capacity @ Ics=65 KA (EDO)

3200A Breaking capacity @ Ics=65 KA (EDO)

INCOMMING / BUSCOUPLER AIR CIRCUIT BREAKER: Supplying with fitting and fixing panel mounting open execution 4 pole Air Circuit Breaker type (MDO/EDO) with guide frame and 4 standard auxillary contacts in the existing cubical panel board of the following capacity complete with making necessary connection as specified and directed by the Dept. (ABB Emax/L & T U Power/ Siemens 3 WL/ Schneider Master pact NW) 6A trip system. 1600A Breaking capacity @ Ics=50 KA (MDO)

2000A Breaking capacity @ Ics=65 KA (MDO)

3200A Breaking capacity @ Ics=65 KA (EDO)

OUTGOING MCCB: 4P MCCB with Microprocessor release (Adj Over Load, Short Ckt & neutral setting incl earth protection) Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, neutral adjustable with earth fault protection without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 63A

50KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

33KV, H.T. METERING PANEL- (INDOOR TYPE) Supply, erection, testing and commissioning of Metring cubicle with 11 KV PTs 33 KV/110V, 33 kV CTs 100/5A with trivector meter indoor type as per local Electricity board, getting approval and calibration as required by the Department. complete etc.

TRANSFORMER Supplying, installation, testing and commissioning of the following cast region dry transformer with Off-Circuit tap link complete including the payment of APDCL to be made for supervision charge, labour charge, cost of L.T/H.T metering etc, (excluding the cost of load security) and making necessary arrangement of charging approval of the sub-station from the Chief Electrical inspectorate as directed and specified by the department. Transformer should be as per CEA guidelines as ammended up to date upto 200 KVA star rating up to 5 star, above 200KVA as per CEA guidelines for losses along with LV enclosure. 2000 KVA 33/0.433 KV. Dry transformer with off Circuit tap links

Supply and laying of following size power / control copper cables, solid copper conductor, HLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured, extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) Core-2, 2 XY 10.00 Sq.mm 2 Core Unarmoured U.G. Cable

Armoured 2 XY 2.5 Sq.mm 6 Core Unarmoured

Unarmoured 2 XY 2.5 Sq.mm 12 Core Unarmoured

Supply and laying 11/33 KV HT 3 core stranded compact circular Aluminium Conductor, Conductor screen with extruded semi conducting compound, XLPE Insulated, Insulation Screening with extruded semi conducting compound in combination with copper tape (0.3KA for 1 sec, cores laid up, inner sheath of PVC tape, galvanized flat steel strip armoured and overall PVC sheathed cable confirming to IS 7098 / (PART-I 1985 with latest ammendment cable laid in air or through existing cable trench/ duct/ cable tray/ HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by deptt. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) 240 Sq.mm 3 Core Armoured 33 KV H.T. U.G. Cable

BULK OIL HSD YARD Supply, Installation, Testing & Commissioning of 25 KL capacity mild steel horizontal cylindrical underground HSD tank (2.5M dia & 5.5M length) with shell 6mm and end plate 8mm thick suitable for underground installation complete with manhole accessories, fittings, piping inside the tank Decanting hose, bucket filter etc. with paint with inside surface scrapped clean. Tank will be tested at works under hydrostatic pressure of 5 psi before being painted with two coats of Red Oxide Primer as required as per specifications.

Supply, fixing, testing and commissioning of M.S. heavy class ERW piping (Class-C) conforming to IS : l239 with necessary clamps, supports, anti vibration mountings, hangers and fittings such as bends, tees, reducers etc. painted as per specifications: 80 mm dia

40 mm dia

25 mm dia

VALVES & STRAINERS Supply, Fixing and Testing of following valves, strainers, in the H.S.D. Fuel Handling System piping complete with companion flanges, nut bolts, gaskets, supports and painted etc. as per specifications : Ball valves : 80mm dia.

40mm dia.

25mm dia.

Non return valves :- 40mm dia

Y-strainers :- 40mm dia.

80mm dia.

Supply, Laying, Testing & Commissioning of 1 No. 40mm dia M.S. heavy class ERW piping (Class-C) conforming to IS : 1239 complete with fittings such as bends, tees, reducer sets on surface/hume pipe or directly in ground including excavation, sand cushioning, 4 mm PYPCOT protective covering and refilling the trench etc. as required. In Ground / On surface

Supplying and laying of 1 No. 25mm dia M.S. heavy class ERW piping (Class-C) conforming to IS : 1239 complete with fittings such as bends, tees, reducer sets on surface/hume pipe or directly in ground including excavation, sand cushioning, 4 MM PYPCOT protective covering and refilling the trench etc. as required. On surface/ hume pipe.

Supply and erection of canopy type M.S.Structure made out of 40mm medium class M.S. pipe (Class-B), 25 x 25 x 3 mm angle iron frame work and 14 SWG GI Sheet. Structure shall be grouted in C.C. 1:2:4 foundation for hanging 4 Nos. 9 litre each fire fighting buckets including providing buckets with two coats of anticorrosive paints etc. complete as required.

Supply and installation of 50ltr capacity Chemical Foam Fire Extinguisher with trolley suitable for Petroleum Fires Protection conforming to IS : 5507.

Supply and installation of 5 kg. capacity dry chemical powder type fire extinguishers conforming to IS : 2171.

Supply of suitable sizes sign boards as per IPR :1976 and fixing the same at various locations within the petroleum installation complete with painting and installation.

Supply & erection of 3 HP Flame Proof positive displacement type HSD pump inside the fuel tank yard having mechanical seal complete with all accessories, fixing on M.S. channel including making earthing as required. Suction head not less than 3.5 m

Supply and fixing of flow meter for diesel line as required. 80mm dia.

25mm dia.

Supply, Installation, Testing & Commissioning of 32A Flame Proof out door type isolator switch, M.S. Stand, earthing etc complete as required.

Liasioning work for getting the HSD Yard layout drawing approval and licence / NOC from concern department.

SAFETY EQUIPMENT First aid box as approved by St.John Ambulance Brigade /Indian Red Cross society conforming to IS : 2217 - 1963.

Shock treatment chart duly mounted on a wooden frame with glass on, as required in 2 languages (Hindi & English).

Rubber mat 1000 mm. Wide to withstand 1.1 KV dielectric strength as per latest IS 15652-2006.

Rubber mat 1000 mm. Wide to withstand 11 KV dielectric strength as per latest IS 15652-2006.

ACCESS CONTROL SYSTEM Supply, Installation, Testing & Commissioning of Controllers- Networkable 2 reader/ 2 door Intelligent controller with enclosure and power supply (Enclosure + Power Supply) .Approved Makes:/Avigilon/HID/Honeywell

Supply, installation, testing and commissioning Short Range (up to 9 cm ) Smart Card Reader For Exit of Lift Access Doors , tripod/Flap barrier- Entry & Exit (doors) as per the specification. Approved Makes:/Avigilon/HID/Honeywell

Supply, installation, testing and commissioning of contactless Clamshell 2K /2Application Area Smart Card suitable for Access Door as per the specification. Approved Makes:/Avigilon/HID/Honeywell

Supply, installation, testing and commissioning Access Control System Server Software consisting of Access Control system , Alarm Document , Alarm management , All these along with high end security features consist in single package as per specification. Approved Makes:/Avigilon/HID/Honeywell

Single Door Leaf

Supply and Laying of of 8 Core x 0.2 sq mm multi strand, copper, unarmored shielded Cable as per specification (between the every card readers & the access controllers)

Supply , Installation , Testing and commissioning of CAT 6 UTP cable 23 AWG solid copper conductors Approved Make :Approved Makes: Belden/Siemon/Panduit/Der Wiser/Molex

Power Supply- Supply, Installation , testing and commissioning of 12 V SMPS DC Power Supply Unit, highly regulated and spikes free terminal voltage and heavy sourcing current for regulated terminal voltage.

Magnetic Contact- Supply, Installation, Testing and commissioning of Magnetic Contact.Approved Makes:/Avigilon/HID/Honeywell

Supply , Installation , Testing and commissioning of Single Front Facia Plate consisting of Soft Touch Push Buttons Emergency Exit Door Release and indicator LED to show the door status .Approved Makes:/Avigilon/HID/Honeywell

SITCC of Bacnet Control Systems that bring all the technology and devices together onto a single platform so they work together seamlessly and intelligently. Anything and everything connected to a processor system can be monitored, managed, and controlled — anytime, anywhere from a touch screen, laptop, or smart device.enables you to connect all local devices to the Building Management System (BMS), as well as to control all BMS devices from a touch screen. BACnet/IP support provides a scalable, IP-based platform for implementing fully integrated building management and automation. Integrated control of lighting, shades, HVAC, AV, BMS, security, voice & data, and other connected systems is now faster, simpler and more efficient than ever. Built-in BACnet/IP support enables seamless integration with existing building management systems. All systems run independently and communicate with each other on the same platform, creating a truly smart building. Make : Crestron/ AMX/ Philips. Preffered system integrator: Interioarch Solutions/Techtron India/ times Info system.

SITC of DigitalMedia 8G™ Cable, non-plenum, 1000 ft spool. Make : Crestron/ AMX/ Philips. Preffered system integrator: Interioarch Solutions/Techtron India/ times Info system.

SITC of Control Cable, Non-Plenum, Teal, 1000 ft (304 m) spool. Make : Crestron/ AMX/ Philips. Preffered system integrator: Interioarch Solutions/Techtron India/ times Info system.

SITC of 12x8 DSP Matrix Mixer w/USB Audio, AEC, & Audio Conferencing Interface. Make : Crestron/ AMX/ Philips. Preffered system integrator: Interioarch Solutions/Techtron India/ times Infosystem.

SITC of IR Emitter . 2-pin 3.5mm detachable terminal block for connection to IR Port. Connects to a 2-pin terminal block type IR port, providing a 1-way IR control interface to the device. Make : Crestron/ AMX/ Philips. Preffered system integrator: Interioarch Solutions/Techtron India/ times Infosystem.

SITC of DIN-Rail Mountable power supply to power DIN-RAIL Products.capable to provide at least 60 Watts regulated and limited power at 24 Volts DC not consuming more than 70 W att at full output having multiple connectivity ports to give power to different devices. Make : Crestron/ AMX/ Philips. Preffered system integrator: Interioarch Solutions/Techtron India/ times Infosystem.

SITC of Pass-Through Cable for fliptop Series, HDMI® to HDMI, 18 Gbps, 8 ft (2.4 m). Make : Crestron/ AMX/ Philips. Preffered system integrator: Interioarch Solutions/Techtron India/ times Infosystem.

SITC of Pass-Through Cable for Fliptop Series, HD15 male to HD15 male, VGA, 1080p, 8 ft (2.4 m). Make : Crestron/ AMX/ Philips. Preffered system integrator: Interioarch Solutions/Techtron India/ times Infosystem.

SITc of Universal Power supply for the flip top. Make : Crestron/ AMX/ Philips. Preffered system integrator: Interioarch Solutions/Techtron India/ times Infosystem.

SITC of Computer VGA Interface Cable w/Audio, 6 ft. Make : Crestron/ AMX/ Philips. Preffered system integrator: Interioarch Solutions/Techtron India/ times Infosystem.

SITC of HDMI® Interface Cable, 18 Gbps, 6 ft (1.8 m). Make : Crestron/ AMX/ Philips. Preffered system integrator: Interioarch Solutions/Techtron India/ times Infosystem.

SITC of High-Definition Video Scaler, VGA In, HDMI ® Out. Make: Crestron/ AMX/ Philips. Preffered system integrator: Interioarch Solutions/Techtron India/ times Infosystem.

Supply, Installation, Testing & Commissioning of Locks US Standards Mortise with five latches, Card capacity 1-99, Golden &Silver color, 13.56 MHZ mifare card, Special indoor safe bolt, Zine alloy elegant Look, 4 AA Batteries, Low voltage warning etc as per technical specification and as required.

Supply, Installation, Testing & Commissioning of CR 50 W Encoder as per technical specification and as required.

Supply, Installation, Testing & Commissioning of Energy saving switch ( Key Tag) as per technical specification and as required.

Supply, Installation, Testing & Commissioning of Card with data space as per technical specification and as required.

Supply, Installation, Testing & Commissioning of Locks management software, PC, Monitor etc as per technical specification and as required.

HVAC WORKS Chilled Water Piping With Nitrile Rubber Insulation Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 350 mm dia. (32 mm thick insulation)

250 mm dia. (32 mm thick insulation)

200 mm dia. (32 mm thick insulation)

150 mm dia. (32 mm thick insulation)

125 mm dia. (32 mm thick insulation)

100 mm dia. (32 mm thick insulation)

80 mm dia. (32 mm thick insulation)

65 mm dia. (32 mm thick insulation)

50 mm dia. (32 mm thick insulation)

40 mm dia. (32 mm thick insulation)

32 mm dia. (19 mm thick insulation)

25 mm dia. (19 mm thick insulation)

Part III Chilled Water Piping & Pipe Insulation Work. Manual Balancing Valves BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified. 200 mm dia (For Chiller)

100 mm dia (For HWG)

Valves & Strainer Supply, installation, testing and commissioning of following valves in chilled / hot water line as per specification given in the tender. Valves shall be insulated as per pipe insulation material & thickness given above. BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified 200 mm dia

150 mm dia

125 mm dia

100 mm dia

80 mm dia

65 mm dia

50 mm dia

NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation including insulation as specified. 200 mm dia

100 mm dia

Y-strainer 200 mm dia

100 mm dia

Part III Chilled Water Piping & Pipe Insulation Work. 80 mm dia

65 mm dia

50 mm dia

40 mm dia

Pressure Gauges Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required.

Thermometer Providing & fixing in position the mercury in glass industrial type thermometers.

Part IV Condenser Water Piping Work. Condenser Water Piping Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS 'C' class along with necessary clamps, vibration isolators and fittings such as bends, tees etc..but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:-The Pipes size 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 250 mm dia pipe

200 mm dia pipe

Motorised Butterfly Valves Supplying, fixing, testing and commissioning of following sizes Motorized Butterfly Valve with CI Body, SS Disc, O - ring and minimum PN-16 pressure rating, conforming to BS 5155, IS 13095, with IP-55 actuator, capable of accepting upto 10V DC , and upto 20 mA electric signal and providing similar transduced feedback output to control system as required. 250 mm dia (For Condenser Out, Cooling Tower In & Out)

Valves & Strainer Supplying, fixing, testing and commissioning of following valves, gauges and strainers for condenser water circulation as per specifications. BUTTERFLY VALVE (MANUAL) with CI body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 50 mm dia

Thermometer Providing & fixing in position the mercury in glass industrial type thermometers.

Pressure Gauges Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required.

Part V Air Distribution Work. Rectangular GI Ducting (Factory Made - L Shape) Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Thickness 0.63 mm sheet

Thickness 0.80 mm sheet

Thickness 1.00 mm sheet

Thickness 1.25 mm sheet

Site Fabricated GI Ducting Supply, installation, balancing and commissioning of site fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required 24 G (Up To 750 mm)

22 G (751 to 1500 mm)

20 G (1501 to 2250 mm)

18 G (Above 2250 mm)

Duct Accoustic Lining Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m3, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.

Part V Air Distribution Work. Fire Dampers & Actuator Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. Fire Damper

Actuator

Grilles, Diffusers, VCD Supply, installtion and testing of Powder coated Aluminium extruded grills / diffusers as per specifications given in tender and of following sizes. Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core.

GSS Duct Damper Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc., as per specifications

Part V Air Distribution Work. Supply Duct Insulation "Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class ""O"") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 19 mm"

ARI Certified Rotary Screw Water Cooled Chilling Machine With Air Cooled VFD & Microprocessor Based Control Panel (Capacity - 400 TR) Supply, installation, testing and commissioning of Rotary Screw Water cooled water Chilling M/C of 400 TR actual capacity at below mentioned operating conditions with R - 134 A refrigerant, open / semihermatic / hermatically sealed compressor, driven by suitable KW Sq. Cage induction motor with variable speed drive (VFD), watercooled shell & tube condenser, insulated shell and tube flooded chiller, flow switches at condenser & chiller outlet, flexible pipe connector at condenser & chiller inlet / outlet, refrigerant piping, Refrigerant and Oil (First Charge), Microprocessor based control panel, chiller / floor mounted aircooled VSD with IP 54 enclosure, active harmonic filters & accessories etc. all mounted on M.S. frame. Motor shall be suitable for 415 volts ± 10%, 50Hz ± 5 %, three phase A.C. supply. The chilling m/c as described above shall be in line with specifications & shall have interface card compatible with BMS system. Actual capacity of chillers shall be based on the parameters given below & power consumption / TR at 100%, 75%, 50% & 25% load shall be based on ARI Condition.

Condenser CDW IN - 29.44º C. CDW OUT - 33.61º C. FLOW - 6048 LPM Fouling Factor (MKS) - 0.0002 Pressure Drop Max - 6.5 Meter Chiller CHW IN - 12.22º C. CHW OUT - 6.67º C. FLOW - 3629 LPM Fouling Factor (MKS) - 0.0001 Pressure Drop Max - 6.5 Meter COP At AHRI Condition - 5.8 (Min) Power Consumption Of Chiller / TR At Tender Condition Mentioned Above (Max) - 0.68 The price quoted for supply, installation, testing & commissioning of Rotary Screw Water Chilling Unit shall be inclusive of all duties & taxes, insurance, transportation / shipment cost from works to site, loading / unloading, port clearance charges etc. as required in Indian Rupees. (3W+1S) Condenser Water Pumps Set Supply, installation, testing and commissioning of Vertical Inline condenser water centrifugal pump sets with bronze impeller for condenser water recirculation complete with TEFC (IE3) Sq. Cage induction motor with class "F" insulation, base plate, coupling guard, SS Shaft Grade 316, bronze impeller, factory fitted mechanical seal, flexible pipe connector at inlet and outlet etc. conforming to technical specification & as per following parameters.

Condenser Water Pumps Set (3W+1S) Capacity of Each Pump LPM 6048 Pump Head (Mt) 24.0 Motor HP (Proposed) 50.0 Pump Efficiency (Approx) 80% Part I Equipment. Primary Chilled Water Pumps Set Supply, installation, testing and commissioning of Vertical Inline chilled water centrifugal pump sets with bronze impeller for chilled water recirculation complete with TEFC (IE3 rating) and as per IS12615, Sq. Cage induction motor with class "F" insulation, base plate, coupling guard, SS Shaft Grade 316, bronze impeller, factory fitted mechanical seal, flexible pipe connector at inlet and outlet etc. conforming to technical specification & as per following parameters. The chilled water pumps shall also include the cost of thermal insulation.

Primary Chilled Water Pumps Set (3W+1S) Capacity of Each Pump LPM 3629 Pump Head (Mt) 12.00 Motor HP (Proposed) 15.0 Pump Efficiency (Approx) 75% Secondary Chilled Water Pumps Set Supply, installation, testing and commissioning of Vertical Inline chilled water centrifugal pump sets with bronze impeller for chilled water recirculation complete with TEFC (IE3) Sq. Cage induction motor with class "F" insulation, base plate, couplingguard, SS Shaft Grade 316, bronze impeller, factory fitted mechanical seal, flexible pipe connector at inlet and outlet etc. conforming to technical specification & as per following parameters. The chilled water pumps shall also include the cost of thermal insulation. Secondary chilled water pumps shall be suitable for operation on variable frequency drives & conforming to the specifications of variable speed pumping system. Zone - 1, Convention Centre

Secondary Chilled Water Pumps Set (2W+1S) Zone - 1 Capacity of Each Pump LPM 3175 Pump Head (Mt) 18 Pump Motor HP (Proposed) 20 Pump Efficiency (Approx) 80% Zone - 2, Hotel

Secondary Chilled Water Pumps Set (2W+1S) Zone - 2 Capacity of Each Pump LPM 3175 Pump Head (Mt) 18 Pump Motor HP (Proposed) 20 Pump Efficiency (Approx) 80% Variable Speed Pumping System for Secondary Chilled Water Pumps For Zone - 1, Convention Centre Supply, installation, testing and commissioning of Variable Speed Pumping system for Zone I consisting of two numbers 20 HP variable frequency drive (VFD) having IP-54/55 enclosure with heat sink suitably interfaced with other system components, hand / auto macro designed for pumping application, 01 no. dedicated microprocessor based pump logic controller, parallel pumping software duly downloaded, 02 No. Differential Pressure Sensor / Transmitters, interfacing amongst all components and compatibility of I/O signals etc complete with other accessories as required.

Part I Equipment. For Zone - 2, Hotel Supply, installation, testing and commissioning of Variable Speed Pumping system for Zone II consisting of two numbers 20 HP variable frequency drive (VFD) having IP-54/55 enclosure with heat sink suitably interfaced with other system components, hand / auto macro designed for pumping application, 01 no. dedicated microprocessor based pump logic controller, parallel pumping software duly downloaded, 02 No. Differential Pressure Sensor / Transmitters, interfacing amongst all components and compatibility of I/O signals etc complete with other accessories as required.

Hot Water Generator For Winter Heating (For Hotel) Supply, installation, testing and commissioning of electrically operated Hot Water Generator of capacity 240 KW in multiple bank complete with PLC based microprocessor controls, electrical panels, flexible pipe connector etc. confirming to technical specifications section. (2W+1S)

Hot water generator shall meet ASHRAE 90.1-2004 Table 7.8 performance standard Inlet Water Temperature 50 °C Outlet Water Temperature 55 °C Hot Water Pumps Set Supply, installation, testing and commissioning of Vertical Inline hot water centrifugal pump sets with bronze impeller for chilled water recirculation complete with TEFC (IE3) Sq. Cage induction motor with class "F" insulation, base plate, couplingguard, SS Shaft Grade 316, bronze impeller, factory fitted mechanical seal, flexible pipe connector at inlet and outlet etc. conforming to technical specification & as per following parameters. The hot water pumps shall also include the cost of thermal insulation. Hot water pumps shall be suitable for operation on variable frequency drives & conforming to the specifications of variable speed pumping system.

For Hotel Hot Water Pumps Set (2W+1S) Capacity of Each Pump LPM 557 Pump Head (Mt) 25 Pump Motor HP (Proposed) 5 Pump Efficiency (Approx) 75% Part I Equipment. Variable Speed Pumping System for Hot Water Pumps For Hotel Supply, installation, testing and commissioning of Variable Speed Pumping system consisting of three numbers 5 HP variable frequency drive (VFD) having IP-54/55 enclosure with heat sink suitably interfaced with other system components, hand / auto macro designed for pumping application, 01 no. dedicated microprocessor based pump logic controller, parallel pumping software duly downloaded, 02 No. Differential Pressure Sensor / Transmitters, interfacing amongst all components and compatibility of I/O signals etc complete with other accessories as required.

CTI Certified FRP Induced Draft Cooling Tower (450 TR) Supply, installation, testing and commissioning of CTI Certified FRP Induced draft, cross / counter flow, twin fan, direct driven, site erected cooling tower of capacity as mentioned below based on the parameters given below and complete with PVC Fill, Louvers, Drift Eliminator, Weather Proof IP 55 TEFC Motor (IE3), Propeller Fan, FRP Basin with additional sump in the bottom of the basin on every outlet point to avoid vortex formation in the condenser water pipe line, Hot dip galvanised Steel Ladder, Stainless Steel hardware including nut, bolt, washer etc. The cooling tower shall conform to technical specifications given in the tender. The maximum allowable sound power at a distance of 1 M from the cooling Tower shall be less than 75 dB. Tower fan motor shall be suitable for VFD operation and operation of VFD system shall be based approach of cooling tower. Performance required for cooling tower is minimum 38.2 gpm/hp when tested according CTI ATC-105 procedure. Water Flow - 6804 LPM (4 GPM / TR) Designed Wet Bulb Temperature - 27.8 °C Water Inlet / Outlet Temperature - 33.61 °C / 29.44 °C Cooling Tower Basin Height - 300.0 MM Fan Motor HP - 2 x 10 / 12.5 HP, 960 RPM Cooling Tower Capacity: 17,01,000 Kcal/Hr, 3W+1S

VFD System For Cooling Tower Supply, installation, testing and commissioning of VFD having IP-54/55 enclosure from factory with heat sink for each cooling tower fan (10 / 12.5 HP Each, 8 Nos.) with VFD control panel & other accessories as required. VFD control panel shall be installed in the AC Plant Room. The system shall be complete with variable frequency drive (VFD) suitably interfaced with other system components, hand / auto macro designed, 01 no. dedicated microprocessor based logic controller, software duly downloaded, tempearture Sensor / Transmitters, interfacing amongst all components and compatibility of I/O signals etc complete with other accessories as required. Operation of VFD system shall be based approach of cooling tower.

Part I Equipment. Pressurised Expansion Tank (Chilled / Hot Water) Supply, installation, testing and commissioning of pressurised insulated chilled water Expansion Tank of capacity as given below made of MS Sheet & finished with epoxy enamel, having interchangeable butile - EPDM membrane, operating pressure 10 Kg/cm² or as actually required, suitable HP pump, pressure switch, valves, make up water connection, overall height of the tank shall be limited to 3.0 meter & the tank shall be complete with necessary controls etc. as required to make it fully functional. The capacity of each tank shall be 3000 Liters approx. Capacity of tank is for the guidance only & AC Contractor to quote as per actual requirement.

Air & Dirt Separators with Air Release Valve & Drain Valve Supply, Installation, testing & commissioning of a common Air and Dirt Separators as per Specifications on the return chilled water line located at the pump suction and suitable for following flow rate of water. The separator should be complete with high capacity air vent, service valve, non return valve, butterfly valve connection for makeup water inlet, flanges, drain valve etc. Total Chilled Water Flow Rate 11000 LPM

Part II AHU & their Controls Double Skin Floor Mounted AHU Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted (Horizontal / Vertical to suit site), fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, cooling coil made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. Static pressure given below for each AHU is indicative & shall be as per actual requirement based on shop drawings. The capacity of Air-handlers shall be as follows. The AHU shall be with one set of commissioning filter which shall be replaced with actual filter. 1,000 CFM, 35 mm St. Pr., 6 Row, (Ceiling Suspended / Floor Mounted TFA AHU & Without VFD)

2,500 CFM, 35 mm St. Pr., 4 Row, (Ceiling Suspended AHU & Without VFD)

3,000 CFM, 35 mm St. Pr., 4 Row, (Ceiling Suspended AHU & Without VFD)

3,500 CFM, 40 mm St. Pr., 4 Row

4,500 CFM, 45 mm St. Pr., 4 Row

5,000 CFM, 45 mm St. Pr., 6 Row

6,000 CFM, 50 mm St. Pr., 6 Row

7,000 CFM, 50 mm St. Pr., 6 Row

8,000 CFM, 50 mm St. Pr., 6 Row

8,500 CFM, 55 mm St. Pr., 6 Row

9,000 CFM, 55 mm St. Pr., 6 Row

10,000 CFM, 55 mm St. Pr., 6 Row

11,000 CFM, 60 mm St. Pr., 6 Row

13,000 CFM, 60 mm St. Pr., 6 Row

14,000 CFM, 65 mm St. Pr., 6 Row

Part II AHU & their Controls 15,000 CFM, 70 mm St. Pr., 6 Row

16,000 CFM, 70 mm St. Pr., 6 Row

1.5 TR, 3-4 mm external static

2.0 TR, 3-4 mm external static

2.5 TR, 4-5 mm external static

3.0 TR, 4-5 mm external static

3.5 TR, 4-5 mm external static

4.0 TR, 5-6 mm external static

FCU Valves and Copper Connection Set Supply, installation, testing and commissioning of insulated copper connection set for chilled water line consisting of ball valve with strainer at inlet, ball valve at outlet, copper connection set with braided pipe flexible connector at in and out at one end etc excluding 2-Way PIBC modulating control valve (quantified separately) but provision of fixing it as required for smooth functioning of unit. Valves sizes shall be 25 mm up to 2 TR & 32 mm for 2.5 TR & above)

Thermostat for FCU Supply, installation, testing and commissioning of automatic control for Fan Coil Units consisting of pressure independant balancing cum two way control valve (already quantified herein) & digital thermostat, which will have provision of setting of room temperature, setting of fan speed (High, Medium, Low). The quoted price of thermostat shall include the cost of 20mm MS conduits, control cabling, MS Box etc as required. Thermostats shall be interlocked to prevent simultaneous heating and cooling.

Digital Display Type Thermostat For AHU Supply, installation, testing and commissioning of Proportional cooling / heating digital display, communicating type thermostat at air-handler. Temperature Sensor for AHUs are also specified in BMS Part. Thermostat shall be installed in case BMS commissioning is significantly delayed.

Part II AHU & their Controls Pressure Independant Balancing Cum Two Way Control Valve (Cooling Coil For AHU & FCU) Supply, installation, testing and commissioning of Pressure Independant Balancing Cum Two Way Control Valve in a single body equipped with electronic modulating actuator working on 2-10 V DC, 4- 20 mA electric signal. The minimum close off Pressure of actuator must be 1.5 times shut off head of pump as per specifications of following sizes: 15 mm Dia, Maximum 2.4 GPM

19 mm Dia, Maximum 5 GPM

40 mm Dia, Maximum 26 GPM

50 mm Dia, Maximum 54 GPM

65 mm Dia, Maximum 80 GPM

80 mm Dia, Maximum 125 GPM

300 - 400 CFM (8mm static pressure, single phase)

500 - 600 CFM (10mm static pressure, single phase)

700 - 900 CFM (15mm static pressure, single phase)

1000 - 1500 CFM (15mm static pressure, single phase)

1600 - 2000 CFM (15mm static pressure, single phase)

Plastic Propeller Fans Supply, installation, testing and commissioning of propeller exhaust fans of various capacities as given below suitable for 240 volts, 50 Hz, single phase AC supply complete with gravity louvers & speed regulator etc. 100 - 200 CFM (3 mm Ex. St. Pr.)

300 - 500 CFM (3 mm Ex. St. Pr.)

28,000 CFM (25mm st. pr, 1120 mm Dia Axial Fan, 7.5 KW, 1450 RPM Fan Motor, Direct Driven)

22,000 CFM (20mm st. pr, 1000 mm Dia Axial Fan, 5.5 KW, 1450 RPM Fan Motor, Direct Driven)

20,000 CFM (25mm st. pr, 1000 mm Dia Axial Fan, 7.5 KW, 1450 RPM Fan Motor, Direct Driven)

20,000 CFM (20mm st. pr, 1000 mm Dia Axial Fan, 5.5 KW, 1450 RPM Fan Motor, Direct Driven)

18,000 CFM (25mm st. pr, 1000 mm Dia Axial Fan, 5.5 KW, 1450 RPM Fan Motor, Direct Driven)

18,000 CFM (20mm st. pr, 1000 mm Dia Axial Fan, 5.5 KW, 1450 RPM Fan Motor, Direct Driven)

16,000 CFM (20mm st. pr, 900 mm Dia Axial Fan, 3.7 KW, 1450 RPM Fan Motor, Direct Driven)

15,000 CFM (20mm st. pr, 900 mm Dia Axial Fan, 3.7 KW, 1450 RPM Fan Motor, Direct Driven)

12,000 CFM (20mm st. pr, 800 mm Dia Axial Fan, 3.7 KW, 1450 RPM Fan Motor, Direct Driven)

10,000 CFM (20mm st. pr, 800 mm Dia Axial Fan, 2.2 KW, 1450 RPM Fan Motor, Direct Driven)

Part II AHU & their Controls 8,000 CFM (20mm st. pr, 700 mm Dia Axial Fan, 2.2 KW, 1450 RPM Fan Motor, Direct Driven)

4,000 CFM (20mm st. pr, 500 mm Dia Axial Fan, 1.1 KW, 1450 RPM Fan Motor, Direct Driven)

3,000 CFM (20mm st. pr, 500 mm Dia Axial Fan, 1.1 KW, 1450 RPM Fan Motor, Direct Driven)

35,000 CFM, 1 x 1000 mm Dia. Fan, 1 x 18.5 Kw Fan Motor, 50 mm St. Pressure, Monoblock Pump

Part II AHU & their Controls Kitchen Scrubber Unit Dry Type in Double Skin Construction Supply, installation, testing and commissioning of Double Skin Dry Scrubber Unit comprising of Electrostatic Precipitator Module, SISW Exhaust Air Fan & Accessories as required. "Electrostatic section shall in double skin construction made of 22 gauge galvanized sheet with inner sheet high bake epoxy powder coated, washable type Aluminum mesh pre filters, Suitable SISW Backward Curved Kitchen Exhaust Air Fan complete with TEFC Induction Motor, Drive Assembly, Base Frame, Vibration Isolators and other accessories, wire ionizers to create high voltage DC field, aluminum collector plates which should be alternatively charged positive and negative with large collecting area, to work as magnet for charged smoke and oil particles. Average efficiency of 90-95% as per DOP test method. Electrostatic Precipitator should be able to charge the particles from 0.01 micron to 10 microns through stable power supply. Collector cell should be of permanent type and incorporate facility for easy removal for cleaning. The system should be fitted with appropriate overload protection and safety interlock. Operating Voltage – 220V, 50 Hz. Ionizing Voltage – 12.5 – 13 KVDC. Collector Cell Voltage – 6 – 7 KVDC. 30,000 CFM Capacity, St. Pr. as required "

12,000 CFM, 25mm st. pr, 630 mm Dia Fan, 5 HP, 1440 RPM Fan Motor, Belt Driven

25,000 CFM, 25mm st. pr, 900 mm Dia Fan, 12.5 HP, 1440 RPM Fan Motor, Belt Driven

Part II AHU & their Controls Double Skin Floor Mounted Mechanical Ventilation Unit (MVU) With Fan & Filter Section Only "Supply, installation, testing and commissioning of factory fabricated Double Skin Mechanical Ventilation Unit floor mounted type fabricated out of extruded aluminium section with 0.6mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.6 mm plain Galvanised steel sheet inside with blower, blower section and blower motor TEFC (Efficiency IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, pre-filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90%, polished stainless steel drain pan made out of 22 G sheet duly insulated complete with belt drive package etc. The MVU panels shall be insulated with 23mm thick & 36 Kg/m³ density PU foam. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete MVU shall confirm to tender specication. Static pressure given below for each MVU is indicative & shall be as per actual requirement based on shop drawings. The capacity of MVU shall be as follows: 8,000 CFM, 35 mm St. Pr.

CO & CO2 Based Sensing System For Automated Working Of Parking Ventilation Fans (Normal & Fire Mode Both) Supply, installation, testing and commissioning of CO & CO2 based sensing system for automatic running of parking ventilation supply and exahust fans for normal & fire mode operation. Each set of system for each zone shall have four nos. combined CO & CO2 Sensor.

Sensor shall have following measuring range & accuracy:- CO ( Electrochemical Type ) - Minimum measuring range : 0 ~ 500 ppm, CO2 ( NDIR Type )- Minimum measuring range : 0 ~ 5000 ppm & Accuracy < 1% of measuring range. Coverage of each sensor shall be 7500 Sq Ft & three nos shall be placed in each zone Normal mode axial fan shall automatically start when CO measurement is above 30 ppm or CO2 measurement is above 900 ppm. IF CO level reaches 150 ppm then fan in fire mode should start automatically. User should be able to vary these setpoints through HMI / Web based software interface / supervisory controller. Logic Controller shall also have the logic to switch ON the normal mode fan when CO is above 30 ppm & switched OFF again when CO drops below 25 ppm.Also it should switch on the fan if CO2 is above 900 ppm & switch off once CO2 level reaches below 800 ppm . Similarly fire mode fan should also switched on/off when CO level reaches 150 ppm & switched off when ppm reaches below 50. Logic Controller shall also have the facility of Timer & Manual Override for fan operation. Part II AHU & their Controls Standalone, Networkable, Intelligent Microprocessor based Programmable DDC Supply, installation, testing and commissioning of one no. Standalone Intelligent Microprocessor based Programmable DDC (For Each Zone) with inbuilt HMI , Onboard Modbus port & network functionalities based upon KNX protocol along with suitable Enclosures with all accessories including necessary switchgear, step down transformer, internal power and control cabling (excluding power & control cable to Fan), complete in all respect & as required to suit the site conditions etc. Each Set of DDC Controller should have 4 AI, 8 DI, 4 AO, 5 DO & modbus port as per IO Summary given in specification per Each Zone.

VFD For 50% of Basment Parking Ventilation Fan "Supply, installation, testing and commissioning of Imported BMS compitable VFD for AHU Fan Motor having IP-55 enclosure with heat sink, Mains disconnect, Built-in Harmonic Filters, EMC Filters (Electromagnetic Compatibility Filters), 4 PID Controlers, Automatic Energy Optimization / Load dependent flux optimization functionality for maximum energy savings & complying with the tender specifications. 5.5 KW Motor"

Part III Chilled / Hot Water Piping & Pipe Insulation Work. Motorised Butterfly Valves Supply, installation, testing and commissioning of motorised on / off butterfly valves with modulating motor in return chilled & hot water line of each chiller & Hot Water Generator operated through BMS & of following sizes. Valves shall be insulated as per pipe insulation material & thickness given above. 200 mm dia (For Chiller)

100 mm dia (For HWG)

Valves & Strainer Supply, installation, testing and commissioning of following valves in chilled / hot water line as per specification given in the tender. Valves shall be insulated as per pipe insulation material & thickness given above. Globe / Ball Valves 25 mm dia

32 mm dia

40 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified 250 mm dia

300 mm dia

Condensate Drain Piping With Nitrile Rubber Insulation Supply, installation, testing and commissioning of condensate drain water piping of GI 'Medium' class complete with fittings like elbows, tees, reducers, bends, MS flanges, supports, welding, painting etc. as required conforming to tender specifications and of following sizes. Complete pipe shall be duly insulated with Closed Cell Elastomeric Nitrile Rubber of specified pipe section of specified thickness in the tender specification & suitable for indoor / outdoor application. Complete pipe insulation shall also have 200 g/m² factory laminated, treated woven Glass Cloth coating for mechanical and UV protection. 25 mm dia pipe, 19 mm Insulation Tube

32 mm dia pipe, 19 mm Insulation Tube

40 mm dia pipe, 19 mm Insulation Tube

50 mm dia pipe , 19 mm Insulation Tube

65 mm dia pipe, 19 mm Insulation Tube

80 mm dia pipe, 19 mm Insulation Tube

Part III Chilled / Hot Water Piping & Pipe Insulation Work. Auto Air Vent Supply, installation, testing and commissioning of auto air vent valve of following sizes and complying with tender specification. 10 mm dia auto air vent valve

19 mm dia auto air vent valve

25 mm dia auto air vent valve

Aluminium Cladding on Chilled / Condensate Drain Water Insulated Pipes Supplying & finishing of insulated CHW / Condensate drain pipes with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 350 mm dia. (32 mm thick insulation)

250 mm dia. (32 mm thick insulation)

200 mm dia. (32 mm thick insulation)

150 mm dia. (32 mm thick insulation)

125 mm dia. (32 mm thick insulation)

100 mm dia. (32 mm thick insulation)

80 mm dia. (32 mm thick insulation)

65 mm dia. (32 mm thick insulation)

50 mm dia. (32 mm thick insulation)

40 mm dia. (32 mm thick insulation)

32 mm dia. (19 mm thick insulation)

25 mm dia. (19 mm thick insulation)

Aluminium Cladding on Chilled Water Insulated Valves Supplying & finishing of insulated CHW pipes & valves with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 300 mm dia. (32 mm thick insulation)

250 mm dia. (32 mm thick insulation)

200 mm dia. (32 mm thick insulation)

150 mm dia. (32 mm thick insulation)

125 mm dia. (32 mm thick insulation)

100 mm dia. (32 mm thick insulation)

80 mm dia. (32 mm thick insulation)

Part III Chilled / Hot Water Piping & Pipe Insulation Work. 65 mm dia. (32 mm thick insulation)

50 mm dia. (32 mm thick insulation)

40 mm dia. (32 mm thick insulation)

32 mm dia. (19 mm thick insulation)

25 mm dia. (19 mm thick insulation)

Part IV Condenser Water Piping Work. Condenser Water Piping Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS 'C' class along with necessary clamps, vibration isolators and fittings such as bends, tees etc..but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:-The Pipes size 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 50 mm dia pipe

450 mm dia pipe

Manual Balancing Valves "Supply, installation, testing and commissioning of manual balancing valves in return chilled and condenser water line of each chiller, condenser and cooling tower as per tender specification & of following sizes: 250 mm dia (For Condenser Out, Cooling Tower In)"

Valves & Strainer Supply, installation, testing and commissioning of following valves in chilled / condenser water line as per specification given in the tender. "BUTTERFLY VALVE (MANUAL) with CI body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. " 250 mm dia

450 mm dia

NON - RETURN VALVE with dual plate of CI body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating asspecified. 250 mm dia

Pot Strainer Supply, installation, testing and commissioning of Pot - Strainer of the following sizes confirming to tender specification. 300 mm dia

Part V Air Distribution Work. Return Duct Insulation "Supplying and fixing of external thermal insulation on ducts with Aluminium Metalized Cross Linked Closed Cell Polyethylene FR-XLPE insulation, tape & adhesive (pidilite SR -998) as required of following thickness. 13 mm

Grilles, Diffusers, VCD Supply, installtion and testing of Powder coated Aluminium extruded grills / diffusers as per specifications given in tender and of following sizes. Fresh / Exhaust air louvers with bird screen & damper

Volume control GI Dampers to be provided in supply & Exhaust air registers / terminals.

Slot linear air diffusers of following sizes: 2 Slot

High Flow Jet Diffusers Hi flow jet diffusers suitable for 1000 - 1200 CFM each with a throw of minimum 8 - 10 meters.

Factory Fabricated Double Skin Insulated GSS Spiral Round Duct For Positive Pressure up to 70 mm Supply, installation and testing of double skin insulated G.S.S. factory fabricated spiral round duct made in two layers with 13 mm thick closed cell nitrile rubber Class "O" insulation sandwitched in between two layers. The duct fabrication shall comply with the latest IS / SMACNA standard and complete with double skin fittings such as bends, elbows, collar etc as required and as per approved shop drawings. Inner & outer GSS sheet thickness along with spiral / longitudinal seam gauge shall be same as given below & duct shall be installed using Steel Wire Rope Hangers & Supports. Cost of duct shall include all double skin fittings & steel wire rope hangers / supports. Duct shall be supplied with following internal diameter. Up to 650 mm Dia Internal, 24 G

651 to 900 mm Dia Internal, 22 G

901 to 1250 mm Dia Internal, 20 G

For Vent Fan Motor of 5.6 Kw

Isolators 63 A 3 pole isolator switch with sheet metal enclosure, rain protection etc. as required to suit the site condition.

63 A 6 pole isolator switch with sheet metal enclosure, rain protection etc. as required to suit the site condition.

40 A 3 pole isolator switch with sheet metal enclosure, rain protection etc. as required to suit the site condition.

Power & Control Cabling Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. Power Cabling For Chiller 2 x 3.5C x 300 Sq. mm (Rate For Single Run)

For CHW Primary Pump, Cooling Tower Fan (10, 15 HP Each) 2 x 3C x 6 Sq. mm (Rate For Single Run)

For CDW Pump 2 x 3C x 35 Sq. mm (Rate For Single Run)

For CHW Secondary Pump (20.0 HP Each) 2 x 3C x 16 Sq. mm (Rate For Single Run)

For Motor Up to 3.73 Kw 1 x 3C x 4 Sq. mm

For Motor of 5.5 Kw 1 x 3C x 6 Sq. mm

For Motor of 7.5 to 11 Kw 2 x 3C x 6 Sq. mm (Rate For Single Run)

For Inline Fan / FCU 1 x 3C x 2.5 Sq. mm Copper

Part VI Electrical Work. For Hot Water Generator 240 KW 2 x 4C x 185 Sq. mm

Control cabling (PVC insulated Copper conductor of 1.1 KV Grade armoured cable) 3C x 1.5 Sq. mm

4C x 1.5 Sq. mm

5C x 1.5 Sq. mm

Earthing Strip / Wires as per specs. Supply & laying of 32 x 6 mm GI strip recess / surface as strip earth lead including soldering etc. as required.

Supply & laying of 25 x 6 mm GI strip recess / surface as strip earth lead including soldering etc. as required.

Supply & laying of 4 SWG GI wire or in recess for loop earthing as required.

Supply & laying of 6 SWG GI wire or in recess for loop earthing as required.

Supply and fixing rubber matting conforming to IS-15652-2006 complete etc. as required.

Cable Tray Fabricating and installing following size of perforated M.S. Cable trays including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M.S. suspenders and including painting with powder coating etc as required. 100 mm wide x 50 mm x 1.6 mm

150 mm wide x 50 mm x 1.6 mm

300 mm wide x 50 mm x 1.6 mm

450 mm wide x 50 mm x 2 mm

600 mm wide x 50 mm x 2 mm

Junction Box For FCU / Propeller / Inline Fan etc (Single Phase) Supply, Installation, Testing & Commissioning of 4" x 3" x 3" G.I. Box with modular type 6A socket & switch, modular cover plate etc as required at site.

Host PC comprising core i7 processor or later, 3 GHz, 8.0 GB RAM, 1 TB HDD, DVD drive, 6 nos. USB Port, 18.5" SVGA color flat TFT monitor, keyboard, mouse and pre-loaded windows 8 operating system and anti virus software, Laserjet printer (A4 size, B/W)

Supply, installation, testing & commissioning of the following Web Based graphical Software. Providing facilities to create static & animate the graphics, navigation between the pages, display of logs, changing the time zones, popup alarms with single user license & point capacity as per I-O Summary with 20% spare points configurable password protection for the system and should be able to communicate with BACnet/M-BUS/LONWORK & MODBUS devices simultaneously. This software will act as web server & no additional license should require at client side. Application Software for Building Automation System having facility to to exchange information using SQL database. Software shall have the features to calculate the total power consumption, total refrigeration load consumed on every day etc. Critical alarms generated in a day and its status should also be mailed along with daily report.

Supervisory Controllers Network Area / Supervisory Controller for Building Management System (BMS). Network Area Controller Shall support Communication with AC Plant Controllers (DDC controllers) & Other Application Controllers on BACnet, Shall support Communication with Integrator Units as defined below on BACnet / MODBUS / LONWORKS. Router must be compliant with ANSI / ASHRAE 135-2012 (Rev. 1.10)

For Air Handling Units as per IO Summary as required. (2 Nos. AHU with 1 No. DDC)

PART VII BMS Work For All 3 Phase Fans - Fresh Air / Exhaust Air Fan, Airwasher, Scrubber, Pressurisation Fan etc. as required. (4 No. Fans with 1 No. DDC)

For Lift Well, Lift Lobby & Staicase Pressurisation Fans (4 Nos. Fans with 1 No. DDC)

Field instruments As Per I-O Summary Immersion Temperature sensor with thermowell for Chilled water system (4 Nos. Chiller Outlet, 3 Nos. Chilled Water Header, 1 No. Condenser Water Return Header)

Ambient air temperature and humidity sensor

Current relay for pumps (4 Nos. Primary CHW Pumps, 4 Nos. CDW Pumps, Excluding Pumps on VFD)

Differential pressure switch for various vent. fans excluding Inline & Propeller Fans

Differential pressure switch for AHU blower status

Differential pressure switch AHU Pre Filter status

Temperature, RH & IAQ Monitor Standalone, Networkable Temperature, RH & IAQ Monitor along with single / multiple Touchscreen Display in each AHU Room which will have Modbus Protocol inbuilt as a standard, IOT & Webserver Option for Remote Monitoring, inbuilt memory of 1 GB to monitor & datalog CO2 Level (0-5000 ppm), O2 Level (0-25% Vol O2), PM1, PM2.5, PM10 , VOC ( 0-30 ppm of EToH ), 2 nos. temperature sensor (-10 to 60 Deg C) for AHU supply & return air temperature monitoring i.e. at supply for chilled water modulation & at return air stream for AHU VFD modulation, Humidity Parameters (0-100 % non condensing) & shall work on 24VAC/DC.

Integrators for third party systems on BACnet/MODBUS/LONWORKS/OPC/M-BUS and other industry standard Open protocols for the following Third Party Systems. Integrator should have dedicated one Lon, RS-485 & RS-232 Port with minimum of 96 MB storage.Integrator should be able to store trending to ensure gap free storage.The Third Party Integrator should be from the same manufacturer as that of DDC. Chillers on BACnet/MODbus/LONworks Variable Frequency Drives on BACnet/MSTP, MODBUS-RTU Over RS-485

Cabling and Conduiting Communication & Signal Cabling 2C x 1.5 Sq. mm Shielded Tinned Copper Cable.

MS Conduit 25 mm for Signal & Communication Cable

Shree Gautam Construction Co Ltd