GE 861 EWS-83/2024-25

Amount

Dismantling wall and ceiling boards (fibre, pulp, insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed by Engineer-in-Charge.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering complete all as specified and directed by Engineer-in-Charge.

Demolition of brickwork or stone/boulder masonry, biult in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete article complete all as specified and directed by Engineer-in-Charge.

Dismantling timber fillets in framed work , rails, posts, rafters, purlins, etc under 40 sqcm in section complete all as specified and directed by Engineer-in-Charge.

Dismantling timber scantling 40 sqcm and over in section in any position in framed work complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutter (without taking off shutters from the frames) not exc 1.5 sqm each and removing from site complete all as specified and directed by Engineer-in-Charge.

All as per item No 6 above but exc 1.5 sqm and n.exc 4 sqm complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge.

S&F rolled steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafter and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc Fe 410-W(Gde-E-250) quality A complete all as specified and directed by Engineer-in-Charge.

S&F Mild steel plates (Plain or chequered) channels, square cut or notched(ordinary and counter sunk) forming holes, without any attachment Fe 410-W(Gde-E-250) quality A complete all as specified and directed by Engineer-in-Charge.

S&F 16 to 20mm mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 22.5 cm and n.exc 30 cm long complete all as specified and directed by Engineer-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed .

S&F Pre-painted galvalume aluminium zinc coating GI based Plain sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

M&L second class hard wood (clean sawn) in scantling in frame work complete all as specified and directed by Engineer-in-Charge.

S&F 6mm thick Veneered decorative plywood, grade 1(with BWR resin) with decorative face veneers on one faces; fixed with screws to timber frame work complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class hard wood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails of sectional area exc 13 & n.exc 25 Sqcm complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class hard wood plain fillets, square , rectangular or triangular in section, clean sawn,secured with nails of sectional area exc 6 & n.exc 13 Sqcm complete all as specified and directed by Engineer-in-Charge.

Preparation of new surfaces of wood and wood based materials of any description and girth not otherwise described and treated with creosote oil complete all as specified and directed by Engineer-in-Charge.

Material and labour for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick or stone walls or concrete surfaces etc including raking out joints, hacking for key scrubbing down with water complete all as specified and directed by Engineer-in charge.

M&L for rendering 15mm thick on fare faces of brick work or concrete surface in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 5mm thick on concrete surfaces in CM 1:3 on ceiling, finished even and smooth including GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists etc. in walls, ceiling , stanchions , beams etc including all laps, cutting and waste complete all as specified and directed by Engineer-in-Charge.

M&L for 15mm thick cement plastering on brick work or concrete surfaces in cement mortar (1:4) finishing surfaces even and smooth without using extra cement complete all as specified and as directed.

S&F Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock, strike plate etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 25 above but size 105x60mm complete all as specified and directed by Engineer-in-Charge.

S&F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MSD square tube etc all as specified and as directed.

M&L cement concrete type B2 1:3:6 (40mm graded aggregate) in pillars and post (including caps and bases) complete all as specified and directed by Engineer-in-Charge.

S&F 30mm thick flush shutter, solid core construction with block board core and plywood face panels commercial type on both side complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class hard wood 35 mm thick glazed and skeleton shutters open rebated and prepared to receieve glass, gauze, etc. (with or without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a) complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid PVC moulded door shutter, 30 mm thick 2mm thick 3D wood grain Moulded PVC sheet polyurethane painted on the front face & 2mm plain colour PVC sheet on back face complete all as specified and directed by Engineer-in charge.

S&F steel window with side hung shutters including projecting type hinges with steel handle, steel peg stay complete with glazing bar dovetailed/welded complete all as specified and directed by Engineer-in charge.

All as per item No 32 above but without glazing bars complete all as specified and directed by Engineer-in-Charge.

S&F steel ventilator with top hung shutters including hinges, steel handle, steel peg stay complete with glazing bar dovetailed/welded complete all as specified and directed by Engineer-in-Charge.

M&L for framed work such as grills or grating and gate etc with ends of bars shouldered as framed guard bars conforming to Fe-410-0 or 310-0 complete all as specified and directed by Engineer-in-Charge.

S&F Mild steel butt hinges medium weight , cold rolled, 100mm, ISI marked complete all as specified and directed by Engineer-in-Charge.

S&F barrel tower bolts stove enamelled black of size 200 mm complete all as specified and directed by Engineer-in-Charge.

S&F 150mm long (D type) aluminium anodised handles or extruded section (ISI marked) complete all as specified and directed by Engineer-in-Charge.

S&F 300mm long Aluminium alloy, anodised , sliding door bolt with hasp , staple,(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast-aluminium alloy (ISI marked) complete all as specified and directed by Engineer-in-Charge.

S&F Mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

S&F sheet glass ordinary quality 3mm thick and glazing with oil putty or fixed with wooden beads in squares n.exc. 0.50 sqm in each pane complete all as specified and directed by Engineer-in-Charge.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and width of aperture 1.18mm & fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engineer-in-Charge.

M&L for joint free Non-Skid ceramic coloured tiles 6-7mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including provision of screed bed 15mm thick in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured tiles in vertical surfaces 350mmx250mmx7mm/450mmx350mmx7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over backing coat 10mm thick in cement mortar 1:4 complete all as specified and directed,

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

All as per item No 45 above but in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement to match complete over and including 10mm thick cement screed in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Rounding to edges of stone slabs, such as in steps, cooking platform, and other similar situation complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15mm bore steel water tubing & connections, including cleaning for re-fixing or offering credit as per schedule of credit complete all as specified and directed by Engineer-in-Charge.

All as per item No 48 herein before but 20mm bore complete all as specified and directed by Engineer-in-Charge.

S&F 15mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

S&F 20mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

Re-fixing 15mm bore old steel water tubing & connection in new or old position of wall, ceiling, floor etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 52 herein before but 20mm bore of pipe complete all as specified and directed by Engineer-in-Charge.

S&F vitreous china squatting pan "Orrisa Pattern" size 580x440mm white with integral foot rest (excluding flushing cistern) but including flush pipe and trap complete all as specified

S&F in repairs 10 ltr capacity PVC valve less, syphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including bracket and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and directed by Engineer-in-Charge.

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15mm fancy type bib tap, chromium plated with crutch or butterfly handle, screwed down , screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repairs 15mm dia stop valve chromium fancy type , screwed down, high pressure , with crutch or butterfly handle , screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-in-Charge.

M&L 2nd class hardwood clean sawn weather boarding, plain, 20mm thick or feather edged 15mm to 20mm thick and fixed with 30mm laps complete all as specified and directed by Engineer-in-Charge.

M&L for preparing new surfaces of wood of any description , not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all, as specified and directed.

M&L for painting to steel surfaces of any description over 10 Cm width or girth including preparation of new or untreated surfaces and applying with two coats of synthetic enamel paint over one coat of red oxide primer all as specified and directed.

M&L preparing newly plastered surfaces of walls and applying two coats of oil bound distemper over one coat primer on walls over thin layer of wall care putty complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling over thin layer of wall care putty all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces on wall surfaces and applying two coats of cement base paint over a coat of primer complete all as specified.

M&L for complete removal of existing treatment and applying 3mm thick Birla wall care putty and applying two coats of Oil Bound distemper white or tinned over a coat of primer on walls, etc complete all as specified and directed by Engineer-in-Charge.

M&L complete removal of existing treatment and applying two coat of white wash on walls surface over a coat of chalk whitening primer complete all as specified and directed by Engineer-in-Charge.

M&L complete removal of existing treatment and applying two coat of cement base paint over a coat of primer complete all as specified and directed by Engineer-in-Charge.

S&F in repair 75mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

All as per item No 68 above but 110mm (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 75mm PVC(SWR) bend any radius (ISI Marked) complete all as specified and directed

All as per item No 70 above but 110mm dia (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F in repair 75mm PVC(SWR) junction single(single T) equal or unequal (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

All as per item No 72 above but 110mm bore of pipe (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

M&L in repairs 75mm PVC(SWR) floor trap with grating including jointing with solvent cement (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

All as per item No 74 above but 110mm (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 75mm PVC(SWR) vent cowl (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

All as per item No 76 above but 110mm (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F 500 Ltrs capacity rotational moulded polyethylene water storage tanks(cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed in SSR Part-I including dismantling existing water tanks and removing to store complete all as specified and directed by Engineer-in-Charge.

S&F 20mm ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

M&L 18/19mm thick Pre-laminated board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination , fixed with screw to timber frame including taking down existing board of any description complete all as specified and directed by Engineer-in-Charge.

Extra over rates of block board or veneered particle board for external teak wood 18/19mm lipping 6mm thick fixed with nails complete all as specified and directed by Engineer-in-Charge.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanised width of flaps (when open) in 30mm complete all as specified and directed by Engineer-in-Charge.

S&F 150mm hasp and staple, mild steel, wire type stove enamelled black, including bolt to hinge plate and fixed with screw complete all as specified and directed by Engineer-in-Charge.

Taking down carefully aluminium/copper point wiring (light fan socket or power) complete with fitting such as switches, tube lights, ceiling rose, pendants, regulators, MCB DB, MCB'S, Main switch from control board and making good disturbed surfaces of walls, floor to match with existing and keeping items aside in safe custody for reuse such as regulators, light fitting, MCBs all as specified and directed.

M & L for point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green colour) as earth lead in and including PVC casing and capping medium grade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS/ wooden sunk box of required size, & as directed by Engr in Charge & 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified.

All as per srl item No-85 here in above but for One 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5 sq. mm size

All as per srl item No-85 here in above but for One 3 pin socket outlet, 5 Amps, independent, with cables 1.5 sq. mm size

All as per srl item No-85 here in above but for One 3 pin socket outlet, 15 Amps, independent, with cables 4 sq. mm size

S&F switch piano flush type, 05 / 06 Amps single pole, one way 240 volts complete all as specified & directed.

S&F switch socket combination 2 in 1, 3 pin, 5 Amp flush type universal 240 volt complete all as specified and directed by Engineer-in-Charge.

S&F switch socket combination 2 in 1, 3 pin, 15 Amp flush type universal 240 volt complete all as specified and directed by Engineer-in-Charge.

S&F fan step regulator, 120W - 2 module type electronic fan regulator, duly ISI marked with and including connector complete all as specified & directed.

S&F ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified & directed by Engineer -in- Charge.

S&F lamp holder (Angular / Straight), insulated body, with back plate for batten fitting complete all as specified and directed by Engineer-in-Charge.

S&F in replacement LED lamp 9 W all as specified and directed by Egnr-in-Charge.

S&F in replacement round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed and directed by Engineer-in-Charge.

S&F decorative ultra slim linear LED 20 Watt 4' long lighting fixture with extruded al heat sink, environment friendly, energy efficient ready to use pack including LED tube complete with inbuilt electronic driver, PCB, connector block etc. including connecting up three copper flexible cable from ceiling rose to fittings including connecting up and fixed on including two nos PVC square box of required size complete all as specified and directed by Engineer-in-Charge.

S&F in replacement LED Bldg security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engineer-in-Charge.

S&F in replacement sheet metal enclosure Vertical type, Triple pole and neutral, AC, 415 volts, 4 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as directed by Engineer - in - Charge.

S&F in replacement sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 8 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as directed by Engineer - in - Charge.

S&F MCCB 4 Pole 63Amps, AC 415 V, 16kA complete all as specified and directed

Supply and fixing MCB, SP, AC, 240 volts "B" series capacity of 06 to 32 Amps, 10kA and making connections complete all as specified & directed.

Supply & fixing MCB, SPN (single pole neutral), AC, 240 volts, B series capacity 32 Amps 10kA and making connections complete all as specified & directed.

S&F in replacement Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm centre to centre both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1 , Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed by Engineer-in-Charge.

S&F in replacement exhaust fan 300 mm sweep PVC body with louver, 240 volts AC single phase, 50 Hz, ISI marked, including necessary work in wall/sheet, including connection cable, nut bolt and other fixing material complete all as specified and directed by Engineer-in-Charge.

S&F in replacement ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed by Engineer-in-Charge.

Supply and lay cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) 1100 volts grade with stranded aluminium conductor of size 35 Sqmm 3.5 core complete all as specified and directed by Engineer-in-Charge.

S&F in replacement electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.5 m wide and n.exc. 1.5 m deep for foundation of poles/stay/cable etc including getting out in hard/dense soil complete all as specified and directed by Engineer-in-Charge.

M&L for Sand cushioning to cable with dry fine sand in trenches as per SSR part - I complete all as specified Note : punned thickness shall be measured and paid.

M&L for Bricks laid in trenches flat with width equal to length of brick for cable protection well burnt sub class 'B' bricks laid across the cable complete all as specified and directed by Engineer-in charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed by Engineer-in charge.

Removing excavated material n.exc. 50m and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified and directed by Engineer-in charge.

JANDOO AND CO (BID ID -3251057)