Rehabilitation of Bithan Dam and Canal System District Jalore

P&F steel glazed doors, windows and ventilators shutters of standard rolled steel section (IS 1038-1983) joint mitred and welded with steel 13×3 mm lugs 10 cm. long embedded in cement concrete blocks 15×10×10 cm of 1:3:6 ( 1- Cement : 3- coarse sand : 6 - graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of plain glass panes 4mm thick with copper glazing clips and special metal sash putty of approved make, or metal beading with screws complete including priming coat of approved steel primer, excluding the cost of metal beading and fittings except neccessary hinges of pivots steel handles and peg stay etc. as required. Windows side hung ventilator top or center hung (openable ). PWD BSR Building HMH 2022, item 9.19.3

Plaster on new surface on walls in cement sand mortar 1 : 4 including raking of joints etc. complete fine finish: 12 mm thick.PWD BSR Building Ch B-12, item 12.2.3

Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connections, testing etc. as required. . OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . 40 A rating (E06.1.2.3)

P & F rigid PVC pipe (IS: 4985 mark) class 2 (4 Kg./Cm.) approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant.PWD BSR Building HMH 2022 Ch S-3(2),item 3.16.3 110 mm dia

P. and F. Bib Cock ( I.S. : 8931 Mark ) superior quality of approved make :-- Brass 400 gm. 15.00 mm nominal bore(As per PWD BSR Building 2022 , ChapNo-S-2, Item 2.7.1

Finishing walls with Acrylic Smooth exterior paint of required shade including all scaffolding.New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ).[Ref: PWD BSR Integrated (Bldg) 2022 , Chapter B-12 Item No: 12.42]

Providing and fabricating reinforcement for R.C.C. work including straightening, cuting, bending, placing in position and binding ( Including cost of binding wire ) all complete up to floor three level. Hot rolled deformed bars( IS 1139 ) .(As per PWD Building BSR HMH 2022 , Item no 4.13.3) Chap no B-4

P & F rigid PVC pipe fittings (IS: 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant: PWD BSR Ch S-3, 3.17,, Bend 110 mm (3.17.9.ii)

P & F Squre bars or other flat welded to window , ventilators etc.PWD BSR Building 2022 Ch B-9, item 9.27