REPAIR/MAINT SUMERSIBLE PUMPING SETS, LT PANELS, WATER LEVEL INDICATORS, DOSING EQUIPMENT AND CERTAIN MISC WORK AT FATEHGARH CANTT

Amount

Supply & fix in replacement of DOL Starter 415 Volt suitable for 5 HP motor complete all as specified and directed .

Supply & fix in replacement of Contactor ML-3 rangge 50-70 Amp suitable to operate 40-45 HP submersible pumping set complete all as specified and directed.

Supply & fix in replacement of Contactor ML-2 rangge 35-60 Amp suitable to operate 20-40 HP submersible pumping set complete all as specified and directed.

Supply & fix in replacement of Contactor ML-3 range 60-95 Amp suitable to operate 40-45 HP submersible pumping set complete all as specified and directed.

M&L for taking out unserviceable submersible pumping set complete with column pipe any capacity and any type from existing bore well carefully without damaging the p/set including connecting parts and lowering the same after repair including provision of suitable size of nut & bolts with washer and suitable packing for column pipes and connection of submersible cable complete all as directed. ( NOTE: (1) Chain pully block and clamps etc shall be provided by the department. (2) Necessary safety pracaution will be responsibility of the contractor. (3) Parts replaced of submersible pump set shall be measured and paid seperately under relevant item here in after under as supply only. (4) No extra payment will be made to the contractor for note (1) and (2) above

Dismantling of submersible motor 40 to 41 HP and taking out unserviceable spares and burnt copper binding wire complete. M&L for rewinding of submersible motor with insulated copper winding wire including sleeves as per original company and replacement of worn out parts, including grinding & polishing of rotor sleeves and refixing, testing & transport charges complete all as specified & directed. Note:(Parts for following items shall be paid under relevent item here-in-after under as supply).

All as per item above but for motor 30 to 35 HP motor complete all as specified & directed

All as per item above but for motor 25 HP motor complete all as specified & directed

Supply only impeller suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only neck ring suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only shaft sleeve suitable for 25 HP motor of existing make/company complete all as specified & directed.

M & L for rematelizing of pump shaft suitable for 25 HP pump complete all as specified & directed.

Supply only coupling suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only coupling key suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only impeller key suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only stud with nuts suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only thrust bearing suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only lower housing bush suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only upper housing bush suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only rotor shaft sleeve suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only drain plug suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only water seal suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only CI Bowel suitable for 25 HP motor of existing make/company complete all as specified & directed.

M & L for rematalizing of rotor shaft suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only ball bush suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only impeller suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only neck ring suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only shaft sleeve suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

M & L for rematalizing of pump shaft suitable for 30 to 35 HP pump complete all as specified & directed.

Supply only coupling suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only coupling key suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only impeller key suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only stud with nuts suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only thrust bearing suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only lower housing bush suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only upper housing bush suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only rotor shaft sleeve suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only drain plug suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only water seal suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only CI Bowel suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

M&L for rematalizing of rotor shaft suitable for 30 to 35 HP motor complete all as specified & directed.

Supply only ball bush suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only impeller suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only neck ring suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only shaft sleeve suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

M & L for rematalizing of pump shaft suitable for 40 to 41 HP pump complete all as specified & directed.

Supply only coupling suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only coupling key suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only impeller key suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only stud with nuts suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only thrust bearing suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only lower housing bush suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only upper housing bush suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only rotor shaft sleeve suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only drain plug suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only water seal suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only CI Bowel suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

M & L for reamalizing of Rotor shaft suitable for 40 to 41 HP motor complete all as specified & directed.

Supply only ball bush suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply & fix in replacement of Water pressure guage 100 mm dia in size ranging 0 to 25 kg/ sq cm calibration complete with size 3/8"X1/2" and brass cock 1/2" dia complete all as directed.

Supply & fix in replacement of electronic Timer for Star Delta Starter type ETSD2 Cat No TESD 2 timing range 3-30 sec complete all as specified and directed.

Supply & fix in replacement of Single Phase Preventor for 15/25/35/41 HP submersible pumping set motor complete all as specified and directed.

Supply & fix in replacement of overload protection relay for FASD starter ranging 28-42/30-35 Amp complete all as specified and directed.

S&F in replacement of Digital type ampere meter of size 96x96mm with CT 100/5 Amp,AC,3 phase,415 volts complete all as specified & directed.

S&F in replacement of Digital type voltmeter of size 96x96mm AC, 3P, 415 volts complete all as specified and directed.

Supply,fixing ,testing and commissioning in replacment of submersible cable ,flat, 16 sqmm,3 core,PVC insulated and PVC sheathed with multi stranded, copper conductor,1100 Volts grade ,fixed to submersible motor column pipe ,using suitable size of clamps made out of stainless steel flat of size 20 x2 mm with steel nuts ,bolts & washer for every column pipe of 3 m length including complete all as specified and directed.

M&L for MS flanged column pipe of 100 mm dia medium grade all as specified and as directed

M & L in replacement of non-return valves(Reflex) of 100 mm nominal (confirming to IS-5312) dia complete all as specified and as directed

M & L in replacement of non-return valves(Reflex) of 150 mm nominal dia (confirming to IS-5312) complete all as specified and as directed

S&F in replacement MCCB , 4 pole, 415 Volt, fixed type 125 amp with breaking capacity 16 kA including complete electrical connection using appropirate size of copper lugs complate all as specified and directed.

S&F in replacement MCCB , 3 pole, 415 Volt, fixed type 100 amp with breaking capacity 16 kA including complete electrical connection using appropirate size of copper lugs complate all as specified and directed.

Day to day checking and Maintenance of chemical dozing plant/chloronome plant & BP dozer, minor repair/replacement of defective parts installed at New Kashim Bagh pump house complete all as specified and directed. NOTE : (i) Tools/ plant and safety equipment required to complete the job shall be provided by the contractor. (ii) Transportation for the personal deployed for attending the complaints to be provided by the contractor to avoid time delay

All as per item above but at Old Kashim Bagh pump house.

All as per item above but at New Rajput pump house.

All as per item above but at Old Rajput pump house

All as per itemabove but at Sub stock pump house.

All as per item above but at Yadunath pump house.

All as per item above but at Jora Line pump house.

All as per item above but at Moude Line pump house.

All as per itemabove but at Children School Pump house.

All as per item above but at Swimming Pool pump house.

Supply only Chlorine test kit with orthotolodine solution complete all as specified.

Supplying and laying in repalcement of 15 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

M & L in repalcement of CPVC non return valve suitable for chemical dozing pump complete all as specified.

M & L in repalcement of gate valve suitable for CPVC pipe 15 mm dia complete all as specified.

Supply and fill gear oil SAE 80W/90 complete all as specified.

M& L Mild steel plates, plain or chequered, 5mm in thickness Fe-290(Gde E-250) quality A cutting and making into shape as desired as per site requirement including dismantling complete all as specified.

M&L for preparation of new steel surface and applying two coat of black synthetic paint over a coat of red oxide primer on chequered plate complete all as specified and directed

S & F in replacement synthetic rubber insulated mats 2 mm thick for voltage upto 3.3 kV for electrical purpose as per IS 15652 of 2006 (superseding IS 5424) suitable for electrical shock safety of size 2 m x 1 m complete all as specified and directed

Supply, installation and commissioning in replacement of multi cavity, power-free, automatic, erosion feed enabled, controlled release water sanitizer/conditioning treatment station with proportional dozing arrangement consisting of :- (a) Station Base Assembly (80-100 L) with water inlet regulator, overflow vent, water outlet regulator with non-return valve (for standalone gravity flow), water outlet regulator (for offline automated gravity flow), drain valve, fluid level controller, sludge level gauge,and station base buffer. (b) Station Hood Assembly with multi-cavity arrangement (11-13) with lids, processor outlet & processor inlet connections, and flexible connecting duct. (c ) Material of construction : Non metallic thermoplastic/FRP, Maximum temperature : 45 deg centigrade.

Supply only plastic cylindrical sealed disposable sanitiser refill containing solid chlorine for disinfection of drinking water, with arrangement for controlled release of disinfectanct in water, suitable for operation through recommended dozing system. Replacement indication : visual & weight variation, Water contact orifice design : sealed when dry, exposed upon immersion. Operation type : Non contact, non-inhalatory. Cylinder dia : 2.5 inches + 0.5 inches. Cylinder height : Minimum 10.0 inches + 0.5 inches complete all as specified and directed.

Testing of Raw and treated water of capacity 50 KLD STP for the following parameters BOD,COD, Focal Coliform (FC) testing will be carried out from Govt authorised agencies/Lab , the sample of Raw and treated water obtain from STP in sealed plastic containers . NOte:- Transportation charges of water samples for testing shall be borne by the contactor

Material & labour for water sample colletcted from all pump houses of the station for testing from Govt authorised agencies/lab for testing of water for chemical and bacteria logical tests as per IS:10500. Sample of water obtained from pump houses in sealed plastic containesr of 5 ltrs capacity.Transportation charge of water samples for testing shall be borne by the contractor.The following tests are required at each pump houses. (i) pH test (ii) Total Dissolved Solids (TDS) test (iii) Coliform test (Microbiological test) (iv) Total hardness test (v) Calcium hardness test (vi) Fluoride test and (vii) Iron test

M/S BEE ESS ENTERPRISES (BID ID -3237468)

M/S SRI JAGDAMBE TRADERS (BID ID -3237324)