Spl repairs to bldg No P-03 and P-04 MES Key pers accn under GE(South) Bangalore

Dismantling existing water proofing treatment any type and thickness from top surface of roof slab and removing the materials out of MD land complete all as specified and directed.

M&L for PCC, 1:2:4 type B1 (using 20mm graded stone aggregate) as in roof/floor complete all as specified and directed.

M&L for 10 mm thick rendering in cement mortar 1:4 on concrete surfaces mixed with integral water proofing compound as per manufacturer's instructions, surfaces finished even and smooth without using extra cement complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid separately as supply only under relevant item of this schedule)

Supply only integral water proofing compound complete all as specified and directed.

Preparing the new plastered surface of roof, removing the dust and laitance etc, Apply one coat of polymer based priming bond coat 1:4:7 (polymer, water and cement) to seal all the pores on the treated surface. Lay 45GSM glass fibre mesh or geo textile on the primed surface while it is in tacky condition. Apply two coats of PU RoofKoat/Davko K10 on the Glass Fibre Mesh with a gap of 3-4hrs between the coating complete inlcuding taking down and refixing of water supply lines, cabes etc all as specified and as directed.

S&F 1000 Ltrs. Capacity rotational moulded polyethylene water storage tanks (cylinder vertical with class top) hoisted and fixed in position including dismatling and removing to store all as specified.

S&F 25 mm bore Ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) complete, fixed in repairs, all as specified.

S&F 25 mm bore nipple suitable for HDPE water tank. (Min wt 45 gms).

Taking down cement plaster on brick or stone walls etc, incl raking out joints, hacking for key scrubbing down with water, etc.

M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 incl finished even and smooth (without using extra cement).

M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces of ceiling in cement mortar 1:3 incl finished even and smooth (without using extra cement).

M&L for preparation of new plaster surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for complete removal of existing treatment of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for preparation of new plaster surfaces of wall and applying three coats of white wash over 1 mm thick of wall care putty over a coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment of old treated surfaces of walls including washing, rubbing etc. and applying three coats of white wash over 1mm thick wall care putty on walls, ceiling, chajja etc. with all necessary scaffloding etc.

M&L for complete removal of existing treatment of old treated surfaces of walls including washing, rubbing etc. and applying two coats of cement Base paint on walls, ceiling, chajja etc. over a coat ot primer as manufactures instructions with all necessary scafolding etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground floor)

M&L for 75 mm thick, PCC 1:3:6 type C1 (using 20mm graded stone aggregate), finished even and and fair as in plinth protection incl joints filling complete all as specified.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing rubbish ouside MD land.

S&F coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement or coloured cement to match over 15 mm thick screed bed in cement mortar 1:6.

All as per item No 20 above but in skirting with and including 10mm thick cement plaster in CM 1:4.

S&F coloured Glazed ceramic tile in verticle surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 mm thick rendering in CM 1:4

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar incl removal of debries out side MD land.

M&L 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs,pillars, window cills, cooking platforms and like in cement mortar (1:4), 15mm thick including pointing in white cement (1:2) using marble dust with admixture of pigment to match with the granite complete all as specified and directed

M&L 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs,pillars, window cills, cooking platforms, shelf and partition pointing in white cement (1:2) using marble dust with admixture of pigment to match with the granite complete all as specified and directed

Providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and as directed.

M&L for machine cut polished sadarahalli stone, uniform texture, in one piece in trade and risers, skiring of staircase inlcluding rounding the edge, cutting anti skid grooves 3 Nos in each trade, plastering/screed 15mm thick in CM 1:4 complete as specified and as directed.

S&F Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc, overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm including fixing cantilever brackets and connecting union to waste pipe complete all as specified and as directed.

Supply and laying of 20 mm dia CPVC pipe SDR 11 & plain CPVC SDE 11 fitting on wall/ceiling or laying in tfloors Iincluding taking down old tubes 20mm dia, complete all as splecified.

All as per item No 29 above but 25mm dia including taking down 25mm dia pipe all as specified and as directed.

S&F in CPVC brass treaded elbow 20 mm fixed with all as specified.

S&F CPVC brass treaded Tee 20 mm all as specified.

S & F in repair vitreous china washdown water closet pan & trap (pedestal pattern) with plastic water closet seat black closet pattern with flat bottom and cover and mild steel chromium plated or aluminium hinginng device with flush pipe to pedestal pan incl all joints incl connection to drain pipe and flush pipe.

S&F viterous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests Squatting pan orrisa pattern including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor including trap set in and including concrete.

S&F in repair PVC low level flushing cistern 10 ltr capacity, valveless, syphonic action type with inlet, ball valve float and handle incl brakcet and flush pipe 32 mm dia complete all as specified.

S & F in repair vitreous china white wash hand basin flat back size 550x400 mm incl brackets chain & plug and waste pipe waste coupling 32mm dia etc.

S & F PVC connection 15 mm dia with PTMT nuts of length 450 mm.

S&F in repair 32 mm dia PVC waste pipe for sink and WHB of suitable length complete all as specified.

S&F in repairs angle valves male/female threaded 15 mm nominal bore, brass, fancy type, chromium plated, screwed down, high pressure with Capston head, screwed ends for iron/CPVC pipes or for unions complete all as specified and directed.

S&F in repair 15 mm bore Fancy type Bib taps, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed.

S&F in repair 15 mm bore pillar taps, cast copper alloy, fancy type with capstan heads, chromium plated screwed down high pressure with or without lattered 'Hot' or 'Cold' with long screwed for iron pipe and fixed.

S&F in repair Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified

S&F in repair brass chromium plated tubular towel rail 20 mm dia, D type 60 cm long between flanges

S&F shelf of PTMT fixed with and incl Chromium plated brass screws and wooden/plastic cleats (Min wt 300 gms)

S&F in repairs chromium plated grating 100/75 mm dia circular with centre hole/ without hole of approved make and fixing with cement mortar 1:3 on Nahani trap or floor trap complete all as specified.

S&F assembled ready to use stainless steel grade 304, kitchen plate rack inlcuding top/middle shelves of 1.0mm thick sheet, square hollow supports, including bottom hooks, spoon holes, front and back open, size 915x915mm as approved and specified.

S&F 20mm PP-R Gate valves (brass insert) as per requirement of the site

S&F in repairs Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms), conrner type 250mm dia complete all as specified and directed.

S&F in repairs 15mm bore brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed all as specified.

S&F in repair PVC (SWR) pipes 75 mm size in bore single socketed , in any length with rubber ring joints, fixed to walls including dismantling and breaking of pipe and fittings complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 110 mm size in bore single socketed , in any length with rubber ring joints, fixed to walls including dismantling and breaking of pipe and fittings complete all as specified and as directed.

S&F PVC (SWR) bends 75mm any radius

S&F PVC (SWR) bends 110mm any radius

S&F in repairs Stainless steel curtain rod medium weight 25mm dia with and including support wall bracket of and end knobs of polished stainless steel all as specified.

Taking down chowkat or frames with shutter (without taking off shutters from the frame)n. exc 1.5 sqm complete all as specified and directed.

Taking down chowkat or frames with shutter (without taking off shutters from the frame) exc 1.5 sqm but n.exc 4 Sqm etc complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube and fixing in position with hold fast, complete all as specified and directed.

M &L factory made solid pannel PVC door shutter 30mm thick (style) consisting of frame made out of MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck in side with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame wedded /sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at side,including two Nos tower bolts/ Handles for each shutter as per specification and drawing upto complete all as specified and as directed.

M&L for 105x60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed.

M&L for 125x60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed.

S&F powder coated, min thickness (50 micron) aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed.

Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 not exc half brick wall all as specified and as specified.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hold fasts; wall ties; and similar small articles conforming to Fe-290 Gde-E-165

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type lamination on both sides complete all as specified and as directed.

S&F stainlees steel 150mm door handles with stainless steel screws all as specified and as directed.

S&F stainlees steel 150mm tower bolt with stainless steel screws all as specified and as directed.

S&F stainlees steel 250mm sliding door bolt with stainless steel screws all as specified and as directed.

S&F mild steel 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete (Helical door spring) including welding to steel chowkhats if required all as specified.

S&F powder coated aluminium anodised frame for doors, windows vetilators with one of more rebates incl joining cleat for fixing etc, with powder coating complete all as specified and directed.

S&F Powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified.

S&F stainless steel 75/100 mm butt hinges for doors complete all as specified.

S&F framed work such as grills, gratings, support brackets etc., with ends of bars shouldered and/or riveted, or forged into spikers framed guard bars barred iron doors ladders; framed balusters walk ways railings framework of watertanks and similar work conforming to Fe-290 Gde-165.

M&L for powder coated aluminium sliding window shutter sections weighing not less than 0.37 including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, stainless steel screws, anodised aluminium fittings such as locking arrangements, rollers etc complete all as specified and directed. Note - Each shutter area will be measured seperately

S&F sheet glass 4.8mm thick ordinary quality, in squares n exc 0.5 sq. m each pane complete all as specified and directed.

All as per item No 76 above but 4.8mm thick sheet glass exc 0.5 sq. m each pane complete all as specified and directed.

S&F galvanised mild steel wire cloth, 0.56 mm nominal ida of wire and average width of aperature 1.18 mm and fixed with tinned tacks, or galvanised wire staples all as specified and as directed.

S&F 3 mm thick figured glass pin headed type and glazing with oil putty in square n.exc 0.50 Sqm in each pane incl Hacking out old broken glass (any thickness, size, quality or description) from wooden or metal frame including punching or drilling out old glazing pins/spring clips all as specified.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L precast cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in block masonry with solid blocks, exc 10 cm in width and setting in mortar complete 1:6

M&L preparation of new or previously untreated steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enemel paint over a coat of red oxide.

S&F chequered cement concrete tiles 20 cm x 20 cm x 25 mm thick with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors over 15 mm thick screed bed in cement mortar 1:6.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M & L for point wiring with 1100 Volts grade 1.5 sqmm PVC insulated FRLSH unsheated cable with multistandred copper conductor conforming to IS: 694:1990 (for phase, Neutral and and Earth) in casing caping/ PVC Conduit all accessories, with cast iron / pressed steel terminal box of sutaible size duly painted inner & outside by anticorrosive paint, including plastic laminated sheet 1.6 mm thick for mounting switches, socket cover with fitting screw washer, including cutting chasses in wall/floor/roof for fixing of casing caping/ PVC Conduit and making good the distributed surfaces matching with existing complete all as specified and as directed by Engr-In-Charge.

M & L for One Light/ Fan point on same switch circuit board with other switches complete all as specified and directed by Engr-In-Charge

One switch / 5 Amp socket outlet point as same board with other switches complete all as specified and directed by Engr-In-Charge

One 3 pin 5 Amps socket outlet point on independent board complete all as specified and as directed by Engr-In-Charge.

One Bell point controlled by one switch complete all as specified and as directed by Engr-In-Charge.

One light point controlled by two way switch complete all as specified and directed by Engr-In-Charge

M&L switch socket outlet 2in1, 3pin,5A complete all as specified and as directed by Engr-In-Charge.

M & L switch piano, flush type single pole, 5 Amps complete all as specified and as directed by Engr-In-Charge.

S&F Bell push piano type, 5 Amps complete all as specified and directed by Engr-In-Charge.

S&F call bell, musical type, 230 volts AC single pole complete all as specified and as directed by Engr-In-Charge.

S&F Fan Regulator step type 120W modular type Complete all as specified and as directed by Engr-In- Charge.

M&L ceiling rose surface bakelite 65x50 mm two to three terminals.complete all as specified and as directed by Engr-In-Charge.

All as per item No 85.01 here in before but with cable 2.5 sqmm wire for power point consealed in wall/ ceiling/ casing caping sutaible for 3 pin 15 Amps socket outlet on independent board complete all as specified and as directed by Engr-In-Charge.

M&L switch socket outlet 2in1, 3pin,15A complete all as specified and as directed by Engr-In-Charge.

M & L switch piano, flush type single pole, 15 Amps complete all as specified and as directed by Engr-In-Charge.

S&F in replacement wall mounting fancy light fitting in plastic body with lamp holder B22 base and diffiuser sutaible for and including 9w LED Lamp of colour as decided with mounting provision complete all as secified as directed by Engr-in-Charge.

M&L sub main wiring surface type with two runs of single core, PVC insulated, unsheathed multi standard copper conductor cable of size 6 Sqmm, 1100 volts grade (FRLS) and one run of 06 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through concealed in wall PVC conduit complete all as specified and as directed by Engr-In-Charge. (Note :- Two runs of 06 Sqmm cable, one run of 06 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length).

S & F in replacement VTPN DB - Dobule Door made out of CRCA mild steel sheet flushed in wall, TPN 4 way with 200 Amp rated bus bar, 415 volt with PVC MCB blanking plate, stove enamelled for incorporated of MCBs, insulators and MCCB of capacity upto 125 Amps TP/FP etc, complete all as specified and as directed by engineer in charge

Supply and fixing MCCB FP 415 Volts 63 Amps, 16 KA complete all as specifed and directed by Engr-In-Charge.

S&F MCB, DB double door type, made out of CRCA mild steel sheet flushed in wall, SPN 8 way with 200 Amps rated bus bar , 240 volts IP-43, with PVC MCB blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of MCB's and isolators etc including complete all as specified and as directed complete all as specified and as directed by Engr-In-Charge.

Supply and fixing MCB SPN 40 Amps, 240 Volts complete all as specified and as directed by Engr-In-Charge.

Supply & fixing MCB SP 06-40 Amp, AC, 240 volts, complete all as specified and as directed by Engr-In-Charge.

Supply and fixing surface & wall mounted LED batten 4feet with extruded aluminium housing and robust construction 20 W system lumen including flexible copper 2 core wire from tube light fitting to ceiling rose required length with all accessories all as specified and directed by Engr-in-Charge.

Supply and fixing surface & wall mounted LED batten 2feet 10 W with luminious efficacy not less than 100 lumen/watt including flexible copper 2/3 core wire from tube light fitting to ceiling rose with mounting provisions and all accessories with color of light warm white/cool day light as reqd at site complete all as specified and directed by Engr-in-Charge.

S&F in replacement building protection light fitting to be mounted on pole/bracket of minimum 35W, 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, corrosion resistant including optics for scattering light complete all as specified and directed by Engr-In-Charge.

Taking down unserviceable ceiling fan, wall mounted fan, cabin fan, exhaust fans etc of any type and size from position, disconnecting electric supply, repair/replacement of unserviceable items, including cleaning oiling/greasing,tightening of nut bolt and refixing matching with existing. complete all as specified and directed by Engr-In-Charge.

Supply only following items to be fixed under item no 105 complete all as specified and directed by Engr-In-Charge. Ball/Roller bearing of size and shape matching with existing suitable for ceiling fans

Supply only following items to be fixed under item no 105 complete all as specified and directed by Engr-In-Charge. Ball/Roller bearing of size and shape matching with existing suitable for exhaust fans

Gun metal bush of size and shape matching with existing suitable for ceiling fans

Gun metal bush of size and shape matching with existing suitable for Exhaust fans

Motor stator for ceiling fans wounded with copper wire of size matching with existing with insulation with casing complete.

Motor stator for exhaust fans upto 250 mm sweep wounded with copper wire of size matching with existing with insulation and casing matching with existing complete.

Motor rotor prewired for ceiling fans of size and type matching with existing

Motor rotor prewired for Exhaust fans/wall mounted fans of size and type matching with existing

Fan blades for ceiling fan of any type and size matching with existing

Fan blade for exhaust fan metal body any type and size with mounting provisions matching with existing.

Plastic cup with screw for ceiling fans

Rubber bush with MS bolts, nuts & washers with 'U' clamps for ceiling fans complete all as specified and as directed.

S&F in replacement capacitor 2.5 Mfd suitable for ceiling / exhaust /wall mounting fans complete all as specified and as directed.

S&F in replacement down rod of 30/45 cm with nut, bolts and safety pin for ceiling fans complete all as specified and as directed.

M&L for Preparation of surface & painting the ceiling fans with blades complete after cleaning & applying one coat of stove enamelled white paint by spray painting, writing No complete all as specified & as directed by Engr -in-Charge.

M&L for Preparation of surface & painting the Exaust fans with blades complete after cleaning & applying one coat of stove enamelled white paint by spray painting, writing No complete all as specified & as directed by Engr -in-Charge.

Taking down, dismantling of geysers of any type/capacity from site for repair and Inspection, cleaning, descaling, brazing inner tank, internal wiring including replacement of unserviceable items as reqd, reassembling & reinstallation after necessary repair incuding testing after repair complete all as specified & directed. Note :(a) Replacement of major unserviceable items shall be measured & paid separately under respective item of work.. (b)Cost of replacement for minor items like washers, gaskets, nuts, bolts etc and items not mentioned below is deemed to be include in quoted rates.

Supply only following items to be fixed under item no 106 complete all as specified and directed by Engr-In-Charge. Inner tank for geyser of capacity 25 ltrs of shape matching with existing.

Siphon Assembly suitable for geyser of capacity 25 ltrs of shape matching with existing.

Heating element rated 1.5/2.0 KW with mounting provisions round/tikona as reqd of shape matching with existing

Thermostat with auto cutoff provision switch capillary/screw type, with range 0-80 deg celcius of shape and size matching with existing suitable for geyser of capacity 25/50 Ltrs.

Indicator lamp red and green with coloured diffuser for geysers matching with existing.

Safety valve/high pressure valve matching with existing for geysers

NRV for geysers matching with existing.

Base fixing cover matching with existing.

Cover outer for geyser of capacity 25/50 ltrs of shape and size matching with existing.

S&F in replacement meter box, Size not less than 200mm x 150mm x 100mm, fabricated out of sheet steel, wall mounting meter box suitable for mounting 1 nos energy meters of size matching with existing, concealed type, painted with stove enamelled paint over a coat of red oxide primer on 2.0mm thick sheet steel, weather proof with double stud hinged door front open with internal locking arrengement and externally locking arrengement with aldrop bolt and meter mounting sheet sutaible size should be fixed inside box including dismantling old meters and cutouts from old box and refixing energy meter with complete connection in new meter box complete all as specifed and as directed by Engr-In-Charge.

M & L earthing complete with GI earth plate Electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth plate not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanished earth wire 4.0 mm dia by means of bolts, nuts check and washers of GI or steel all as shown in electrical plate No. 3 of SSR Pt -I connected to earthing test point all as specified or indicated including GI pipe 15 mm dia light grade for earth wire protection, necessary excavation, earth work in any type of soil, PCC chamber and RCC cover slab, connecting lead wire from test point to DB complete all as specified & as directed by Engr-In-Charge.

Supply and laying 40 mm GI pipe fitting tubes medium grade galvanished with all fittings complete laid in trenches including taking down the old unserviceable GI pipe from trenches Complete all as specified and as directed by Engr-In-Charge.

Supply and laying 25 mm GI pipe fitting tubes medium grade galvanished with all fittings complete laid in trenches including taking down the old unserviceable GI pipe from trenches Complete all as specified and as directed by Engr-In-Charge.

Supply and laying 20 mm GI pipe fitting tubes medium grade galvanished with all fittings complete laid in trenches including taking down the old unserviceable GI pipe from trenches Complete all as specified and as directed by Engr-In-Charge.

S & F of float valves of size 20 mm and as reqired at site as complete brass fitting with rod and plastic ball Complete all as specified and as directed by Engr-in-in Charge.

S & F gun metal gate valve with inner wheel head, screwed both ends in iron pipe and fixed of Size 20 mm Complete all as specifed and as directed by Engr-In-Charge.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm x 4 core including taking down unserviceable UG cable complete all as specified and directed by Engr-In-Charge.

Excavation in trenches in soft /loose soil not exceeding 1.5 M wide and not exceeding 1.5 M in depth for laying of UG cables etc and getting out complete all as specified and as directed by Engr-In-Charge.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cms in any type of soil complete all as specified and as directed by Engr-In-Charge.

Removing excavated soil to a distance not exceeding 50 mtrs and depositing where directed at a level not exceeding 1.5 M above the starting point all as directed.

M&L for sand cushioning in trenches for bricks of u/g cable with coarse sand laid dry in trenches with uniform thickness complete all as specified and as directed by Engr-In-Charge.

Supply and lay burnt bricks of sub class 'B' laid dry across in trenches for cable protection all as specified and directed Complete all as specified and as directed by Engr - In - Charge.