PROVN OF CHANGING ROOM FACILITY NEAR WATERMANSHIP TRG AREA AND PARADE CUM ENROLLING SHED NEAR BLDG NO T-8A AT ROWRIAH UNDER GE JORHAT

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft / loose soil etc complete all as specified and as directed by Engr in Charge.

Excavation in trenches n exc 1.5 mtr wide and depth n exc 1.5 mtr deep for foundation, etc n exc 10 sqmtr on plan, in soft/loose soil and getting out complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated materials (soil) n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as directed.

M&L for Earth filling in floor including spreading, levelling, watering and consolidation and well ramming in layers not exc 25 cm complete all as specified and as directed.

M&L for PCC (1:4:8), type D2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for RCC M-25 ( Design mix ) using 20 mm graded stone aggregate) as in foundation, footing, plinth beam, bases for columns etc and mass concrete complete all as specified and directed.

M&L for RCC M-25 ( Design mix ) (using 20 mm graded stone aggregate) as in columns, pillars, posts etc complete all as specified and directed..

M&L for RCC M-25 ( Design mix ) (using 20 mm graded stone aggregate) as in Beams, cantilevers, bressummers,lintels over 1.5m span complete all as specified and directed.

M&L for RCC M-25 ( Design mix) using 20 mm graded stone aggregate) as in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work;not exceeding 200 mm thick (Horizontal or sloping) complete all as specified and as directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers,lintels, cantilevers, shelves including supports,overhangs,etc. also splays between floors and beams, etc. complete all as specified and as directed.

M&L for Formwork to sides of pillars,posts, struts, piers, columns and stanchions etc. complete all as specified and as directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

M&L for Mild steel TMT deformed bars, 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed.

M&L for Mild steel TMT deformed bars, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders confirming to Fe 500D complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base of floor , finished even and fair without using extra cement complete all as specified and as directed.

M&L for Sand filling (river,dry and clean sand) under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for 25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in floor , finished even and fair without using extra cement complete all as specified and as directed.

M&L for Non - Skid ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,conforming to IS 15622, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement sand mortar (1:6), complete all as specified and as directed

M&L for Glazed ceramic coloured , 300 mm X 200 mm X 6 mm thick , on vertical surfaces of wall such as dados etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick screed bed or bedding layer of cement sand mortar (1:4), complete all as specified and as directed.

M&L for Polythene film, black, 50 micron laid in floors etc complete all as specified and as directed.

M&L for Brick work with sub class‘B’ bricks,well kiln burnt , straight or curved on plan exc 6m mean radius, built in cement sand mortar 1:6 etc complete all as specified and as directed.

M&L for Brickwork with subclass ‘B’ bricks, well kiln burnt , straight or curved on plan to any radius in half brick thick walls built in cement sand mortar 1:4 etc complete all as directed.

S&F Mild steel work as in tubular trusses , purlins, and posts etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 etc complete all as specified and as directed.

S&F Rolled mild steel sections as in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete Fe-410-W.Gde-E-250 ,quality A complete all as specified and as directed.

S&F Pre-painted, galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws,complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed.

S&F Mild steel work as in Bands, straps, supports or stays for rainwater, ventilating pipes, clamps;hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 etc complete all as specified and as directed.

S&F factory made Steel ventilator with top hung shutter including hinges, steel pegstay, complete all as specified and as directed.

M&L for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on other than fair face of brickwork and finishing surface even and smooth without using extra cement, complete all as specified and directed.

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framedguard bars; barred iron doors;ladders; framed balusters; walkways; railings; framework ofwater tanks and similar workcon- forming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality type and glazing with oil putty in squares n.exc 0.5 sqm in each pane etc complete all as specified and as directed.

M&L for rendering 5 mm thick, cement plaster, in cement sand mortar (1:4) mixed with water proofing compound @ 3% by the weight of cement used or as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surface in walls, complete all as specified and directed. Note: - (Water proofing compound shall be measured and paid separately)

Supply only integral water proofing compound ISI marked etc complete all as specified and as directed.

M&L for 75 mm thick plain cement concrete (1:3:6) type C-2 (using 40 mm graded stone aggregates) as in plinth protection, finishing surface even and smooth without using extra cement including necessary formwork complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C1 using 20 mm graded aggregate as in surface channels and drains including necessary formwork etc complete all as specified and as directed.

M&L for 25 mm thick Damp proof course in cement sand mortar 1:2 mixed with intrgral water proofing compound @ 3% by the weight of cement ,applied to horizontal or vertical surfaces including necessary formwork and applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m complete all as specified and as directed.

S&F PVC (Plastic polymer Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 litres, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections and good to disturbed surface with cement sand mortar 1:3 complete all as directed by Engineer-in-Charge Make:- Prayag cat part no.701 or equivalent make in Parryware / Hindware.

S&F PVC connection pipe 15 mm size with PTMT nuts of length 450 mm long etc complete all as specified and as directed by Engineer-in-Charge .Make:- Prayag / Parryware / Hindware.

S&F CP bib cock 15 mm bore, cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down, high pressure, screwed for iron pipe complete all as specified and as directed. Make:- Prayag cat part no. 8306 or equivalent make of Pearl / Hindware / Jaquar

S&F CP stop cock 15 mm bore, cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down, high pressure, screwed for iron pipe complete all as specified and as directed. Make:- Prayag cat part No 7326 /7328 or equivalent make in Jaquar / Hindware.

Supply , laying and connection, GI water tubing , 15 mm bore , medium grade, including new GI fittings such as tee, bend, nipple, socket, reducer, flange, union etc on wall , ceiling or laid in floor etc complete all as specified and as directed by Engr in Charge.

Supply , laying and connection, GI water tubing , 20 mm bore , medium grade, including new GI fittings such as tee, bend, nipple, socket, reducer, flange, union etc on wall , ceiling or laid in floor etc complete all as specified and as directed by Engr in Charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing etc complete all as specified and directed.

S&F Factory made solid panel wire gauge PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling shall be of wire gauge .The wire gauge shall be wrapped on an additional square 8 mm MS soild tube . Wire gauge shall be stretched to tightened firmly,fixed in the frame at site etc complete all as specified and as directed.

S&F 100 mm Butt hinges, stainless steel ,medium weight cold rolled mild steel complete all as specified and directed

S&F Aluminium anodised barrel tower bolt, extruded type, 100 mm long, complete all as specified and directed.

S&F Aluminium handles, cast type, anodized, 100 mm size, complete all as specified and directed.

S & F PVC (SWR) Junction single, (Single T) equal or unequal , 110 mm bore with access door etc complete all as specified and as directed.Make:- Supreme / Prayag / Prince

S & F PVC (SWR) vent cowl , 75 mm dia etc complete all as specified and as directed.Make:- Supreme / Prayag / Prince

S&F PVC (SWR) pipes , 110 mm bore , single socketed in any length with rubber ring joints fixed to walls with mild steel clamps made out of flat iron of size 25 mm x 3 mm including necessary nuts and bolts etc complete all as specified and as directed.Make:- Supreme / Prayag / Kanha / Prince

S&F PVC (SWR) pipes , 110 mm bore , single socketed in any length with rubber ring joints , laid in trenches or on floor etc complete all as specified and as directed.Make:- Supreme / Prayag / Kanha / Prince

S&F PVC (SWR) pipes , 75 mm bore , single socketed in any length with rubber ring joints , laid in trenches or on floor etc complete all as specified and as directed.Make:- Supreme / Prayag / Kanha / Prince

S&F PVC (SWR) floor trap, plain 75 mm size with grating including jointing with solvent cement etc complete all as specified and as directed.Make:- Supreme / Prayag / Kanha / Prince

S & F PVC (SWR) Junction single, (Single T) equal or unequal , 75 mm bore with access door etc complete all as specified and as directed.Make:- Supreme / Prayag / Prince

S & F PVC (SWR) bends of any radius , 110 mm bore etc complete all as specified and as directed.Make:- Supreme / Prayag / Prince

S & F PVC (SWR) bends of any radius , 75 mm bore etc complete all as specified and as directed.Make:- Supreme / Prayag / Prince

S&F Rotational moulded polyethylene 1000 ltrs capacity water storage tanks ,white or black colour , three layered, (ISI marked) (cylindrical vertical with closed top) hoisted and fixed in position including 20mm dia GI medium grade over flow pipe, approx lenght 1.5 mtr, 25 mm dia wash out pipe with pluged at one end including 20 mm PTMT ball valve high pressure with polythene float and nut etc complete all as per SSR Part-I ,specified and as directed.Make:- Polycon / Polytuf / Sintex.

S&F Vitreous china squatting pan of Orissa Pattern of size 580x 440 mm ,white with ‘P’ or ‘S’ trap , front or back inlet but excluding flushing cistern and flush pipe including placing in position in floor and embedded in cushion of PCC type E2 ( using 40 mm graded crushed stone aggregates), 1:5:10 and finishing the top surfaces to match with the existing flooring complete all as specified and as directed .Make:- Prayag cat part no. 4054 or equivalent make of Pearl / Hindware.

S&F Vitreous china wash hand basin, white, flat back of size 550 mm x 400 mm including bracket, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia, PVC flexible waste pipe of adequate length and dia and etc complete all as specified and as directed by Engineer-in-Charge .Make:- Prayag cat part no. 4645 IRIS or equivalent make of Pearl/ Hindware.

S&F 15 mm bore Pillar taps fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. Make:- Jaquar cat part No :QQT-7011 or equivalent make in Hindware cat part no. F280001 or equivalent make of Parryware / Prayag.

S&F chromium plated shower rose 125 mm size with or without swivel joint of any size etc complete all as specified and as directed.Make:- Prayag cat part no. B0S-05 or equivalent make of Parryware / Hindware.

S&F brass chromium plated tubular towel rail 600mm long between the flanges and 20mm dia etc complete all as specified and as directed.Make:- Prayag cat part no. BA-30 or equivalent make of Parryware / Hindware.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel or iron surface exceeding 10 cm in width or girth including necessary preparation of surfaces complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wall including cornices , pilasters and applying two coats of cement base paint over and including a coat of suitable wall primer etc complete all as specified and as directed.

M&L for preparation of new or previously untreated surfaces of wall and applying three coats of white wash etc complete all as specified and as directed.

S&F Mild steel work as in Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required:hooks (stay), heavy, for largegates; hook and pintle hinges:large hasps and staples; chains;hand made sliding bolts; clamps;hold fasts; wall ties; hooks forhanging fans; plain angle cleatsfor securing purlins to woodtrusses or rafters; knee pieceinserts; two way and three waystraps, plate washers and similarsmall articles conforming to Fe-290 Gde-E-165 etc complete all as specified and as directed.

S&F PVC (SWR) gully trap 125/110 mm,setting and jointing with solvent cement complete all as specified and directed.

M&L for filling of joints with bitumen 85 / 25 mixed with coarse sand 1:3 etc complete all as specified and as directed.

M&L for Granite slab of approved shade 20mm thick Granite (of any type) tiles machine cut, laid over and ncluding cement screed bed 20 mm thick and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone over and including 20 mm thick screed bed in cement sand mortar 1:4 etc including necessary grinding and polishing till entire satisfaction of Engineer in Charge etc complete all as specified and as directed.

S&F Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed. Make:- BIR / Prayag / Zoloto

M&L for plain cement concrete (1:3:6) type C-2 using 20 mm graded aggregate as in foundation , filling and mass concrete etc complete all as specified and as directed.

M&L for 75 mm thick plain cement concrete (1:2:4) type B-1 using 20 mm graded aggregates as in sub base, finishing surface even and fair without using extra cement , complete all as specified and as directed.

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:4) , mixed with water proofing compound , on fair face of brickwork and finishing surface even and smooth without using extra cement, complete all as specified and directed. ( Note:- WPC compound shall be measured and paid seperately under relevant items of BOQ).

Materials and Labour for rendering 20 mm thick, cement plaster, in cement mortar (1:4) , mixed with water proofing compound , on fair face of brickwork and finishing surface even and smooth without using extra cement, complete all as specified and directed. ( Note:- WPC compound shall be measured and paid seperately under relevant items of BOQ).

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:4) , on fair face of brickwork and finishing surface even and smooth without using extra cement, complete all as specified and directed. ( Note:- WPC compound shall be measured and paid seperately under relevant items of BOQ).

M&L for Mild steel TMT deformed bars, 6 to 8 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1, nominal mix, ( using 20mm graded stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc complete all as specified and as directed.

M&L for RCC 1:1.5:3 type A-1, nominal mix, ( using 20mm graded stone aggregate) as in Walls, retaining walls, basementwalls, ballast walls and the like;any thickness; above top of footings; including attached pilaster and buttresses etc complete all as specified and as directed.

M&L for plain cement concrete (1:2:4) type B-2 using 40 mm graded aggregate as in channels and benching to manholes including necessary formwork etc complete all as specified and as directed.

S&F PVC (SWR) pipes , 75 mm bore , single socketed in any length with rubber ring joints , fixed to wall with MS clamp and screws etc complete all as specified and as directed.Make:- Supreme / Prayag / Kanha / Prince

S & F PVC (SWR) vent cowl , 110 mm dia etc complete all as specified and as directed.Make:- Supreme / Prayag / Prince

M&L for PCC ( 1:3:6) type C-2 using 40 mm graded stone aggregate as Concrete bed to drain pipes 110 mm bore including packing under,and haunching against the sides of pipes after they are aid and tested;in etc complete all as specified and as directed.

M&L for Hardcore of crushed stone, gauge n exc 63mm, deposited, spread and levelled well in layers n exc 15cm thick, watered and rammed to a true surface etc complete all as specified and as directed.

M&L for Machine pressed rubber moulded coloured precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment bedded etc complete all as specified and as directed.

M&L for precast cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate , block of size 300 mm x 300 mm x 150 mm thick ,finished at top bullnosed shape and jointed in cement sand mortar 1:4 etc complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5cum, getting out in soft / loose soil , returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and removing surplus soil to a distance n.exc 50 m from starting point etc complete all as specified and as directed.

M&L for PCC 1:3:6 type C-1 ( Using 20 mm graded stone aggregate) as in embedding of poles and similar work etc complete all as specified and as directed.

S&F Mild steel work as in Rolled sections as in main andcross beams, hip and jack rafters;purlins where connected to common rafters and running rails and guides for sliding doors;fixed with angle cleats or other connecting plates conforming to Fe 410-W(Gde-E- 250) quality-A etc complete all as specified and as directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5 cm long and dia of neck 5 to 10 mm etc complete all as specified and as directed.

M&L for preparation of new or previously untreated surfaces of steel or iron of any description and applying two coats of black bituminous paint over and including a coat of red oxide primer etc complete all as specified and directed.

M&L for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on fair face of brickwork and finishing surface even and smooth without using extra cement, complete all as specified and directed.

M&L Point wiring with single runs PVC insulated FRLSH grade, 1100V grade cable with multistranded copper conductor of size 1.5 Sqmm (Nominal area) (ISI Marked) drawn in and including PVC Casing capping of suitable size with all fittings and accessories including PVC rectangular board of suitable size and drawing continuous earth wire of PVC insulated FRLSH grade, unsheathed stranded copper conductor of size 1.5 Sqmm (ISI Marked) as continuous earth wire terminated in and including sunken box for following type of point wiring including making good disturbed of wall complete all as specified in SSR Part-I, 2009 and Part-II, 2010 and as directed by Engineer-in- Charge for one light point / one 3 pin socket outlet 5/6 Amps and one bell point / one fan point on independent board controlled by one one way switch.

All as per Item No. 95.00 here-in-before but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 2.50 Sqmm for one power point of 3 pin 15 Amps on independent board including FRLSH grade (ISI mark), PVC insulated, unsheathed one run multi-stranded copper conductor of size 2.50 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.

Supply and fix Socket outlet (ISI marked), 6 pin , 5 and 15 Amps, flush type, multipurpose , 240 volts complete all as specified and as directed.

Supply and fix, Switch piano (ISI marked) Single pole 240 volts, flush type, one way 15 Amps complete all as specified and directed.

Supply and fix, Switch piano (ISI marked) Single pole 240 volts, flush type, one way 5 Amps complete all as specified and directed.

S&F Ceiling rose, 3 terminals PVC/polycarbonate, isolated body complete all as specified and directed.

S&F LED light fittings and fixtures with co extruded polycarbonate body environmental friendly ,, 10W , 240 volts , trim LED NEO tube light , extruded aluminium / polycarbonate batten with efficient diffuser including necessary electric connection etc complete all as specified and directed.Make:- Wipro Cat part No. LL13-181-65SESL or equivalent make in Havells / Philips / Crompton / Bajaj.

S&F lamp holder, insulated body, with back plate for batten fitting complete all as specified and as directed.

S&F LED bulb 10, watt energy efficient , B 22 , cool day white , 6500K , etc complete all as specified and as directed.Make:- Havells / Bajaj / Philips / Wipro.

S&F MCB SPN 40 amps 240 volts , 50 Hz , breaking capacity 10 kA ''C'' series etc complete all as specified and directed. Make:-L&T / Legrand / Siemens

S&F MCB SP 6-32 amps 240 volts , breaking capacity 10 kA ''C'' series etc complete all as specified and directed. Make:-L&T / Legrand / Siemens

S&F MCB DB SPN 8 ways , double door, IP-43 with 200 amps rated busbar ,Earth bar , neutral links , 240V , complete including blanking plates etc complete all as specified and directed. Make:- L&T ,Cat No.DBSPN008DD or equivalent Model of Make Legrand/Siemens]

Supply and Laying galvanized steel tubing, 40 mm bore, light grade in trenches or fixed to poles / Walls for cable protection including necessary cutting in road / hardstanding of appropriate depth and width and making good of the disturbed portion with PCC 1:3:6 type C-1 ( using 20 mm graded stone aggregate etc complete all as specified and directed

Materials and Labour for earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanised iron or steel earth wire , 4 mm dia ( No. 8 SWG) by means of bolts, nuts check nuts and washers of galvanised steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia. MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown on electrical plate No 3 of SSR Part –I (2009)

S&F Exhaust fan AC single phase 230 / 240 volts of weep 250 mm with plastic self closing louver and making necessary electric connection with flexible copper conductor cable 1.5 sqmm 3 core PVC insulated including cutting holes of appropriate size in brick wall or concrete wall and making good to disturbed surfaces with cement sand mortar 1:3 with necessary paint /white wash to match the existing etc complete all as specified and as directed. Make:- Havells cat part No FHVVEDXOWH10 or equivalent make in Usha / Crompton / Havells / Bajaj.

S&F Decorative ultra slim linear LED batten light fitting with co extruded polycarbonate body enviornmental friendly, energy efficient , E-LITE LED GREEN suitable for 18/20 watt LED 6000K , 240 volts LED tube light ( single side connection ) including 1 x 18/20 watt LED tube rod etc complete all as specified and directed.Make:- Wipro Cat part No. LL13-181-65SESL Havells Cat Part No:LHEXBLP7UN1W018 / Philips Cat part no.DX18W or equivalent make in Havells / Crompton / Bajaj.

S&F Ceiling fan ,1400 mm sweep, white colour , 3 blades , 50 watt , including making electrical connection with flexible copper conductor cable 1.5 sqmm 3 core PVC insulated and all fixing arrangement etc complete all as specified and as directed. Make:- Usha cat part No 1400 MM ENERGIA ISI or equivalent make in Havells / Crompton / Bajaj.

S&F Electronic fan regulator flush type , 4 step type , 120 W , AC , 240 volts , 50 Hz , etc complete all as specified and as directed.

Supply,laying, jointing and testing of , XLPE insulated, PVC sheathed, armoured, heavy duty ,electric cables with aluminium conductor for working voltage up to and including 1100 volts, of cross sectional area 25 sqmm 2 core with aluminium lugs etc complete all as specified and directed.

S&F 20 mm dia 3-layer PP-R Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. etc complete all as specified and directed.

M&L for cutting existing GI pipe 80 / 40 mm bore ( dia) in position for taking out branch connection of 40/25 mm bore ( dia) , inserting 1 No Tee (T) of size 40x40x20mm including providing new reducing tee , all joints and jointing materials etc complete all as specified and as directed.

S&F Stop valves, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

Supply and filling in dry and clean , river sand in cable trenches before and after the cables are laid, as in sand cushioning to cables, complete all as specified and as directed. (Note:- Only punned thickness shall be measured and paid)

Supply and laying common burnt clay building bricks, sub-class‘B’ designation 75, old size bricks, in cable trenches, as cable protection, complete all as specified and directed.

Supply,laying, jointing and testing of , XLPE insulated, PVC sheathed, armoured, heavy duty ,electric cables with aluminium conductor for working voltage up to and including 1100 volts, of cross sectional area 16 sqmm 2 core with aluminium lugs etc complete all as specified and directed.

M/S N M TRADERS

PEE BEE INDIA