Construction of Barrack for CISF near Switch Yard at BSPS, Surangani

Amount

Construction of Barrack for CISF near Switch Yard at BSPS, Surangani.

Cutting in earth work and disposal of excavated earth upto a lead of 20 metres.: 50% spade work % 50% pick work.

Excavation in foundations, trenches etc., in earth work, lift upto 1.50 Metres stacking the eacavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15cm. layers, when required in to plinths sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with in a lead of 20 metres. 50% spade work % 50% pick work.

Providing and laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in: Foundation and plinth.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in: Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in:

Foundation, footings basis of columns etc. and mass concrete.

Columns, pillars, posts and struts Square, rectangular or polygonal in plan.

Sides and soffits of beams, beam haunchings, cantilevers,girders, bressumers and lintels exceeding 1 Mtr. in depth in all heights from floor.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like. Floors etc.upto 200mm. In thickness.

Edges of slabs and breaks in floors and walls Under 20 cm. wide.

Providing and laying cement concrete 1:5:10 (1cement :5sand :10 graded stone aggregate 40mm. nominal size) with 15 % plum and curing complete excluding cost of form work in retaining walls/ Breast walls, the size of plums shall usually be 150mm. to 300mm. as per H.P.P.W.D. Specification.

Providing and laying cement concrete 1:1.5:3 (1cement :1.5 sand :3 graded stone aggregate 20mm. nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:

Foundation footings bases of columns and the like and mass concrete.

Lintels, beams girders bressumers and cantilevers upto floor two level.

Column, pillars, posts and struts upto floor two level.

Suspended floors, roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto floor two level.

Providing mild steel/Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level : Tor Steel.

Stone soling properly hand packed filling with intersticks with spalls and consolidating to the required gradient including spreading watering & compacting binding material moorem or earth etc. 100mm spread thickness (finished work with material & labour).

Stone filling behind retaining walls :

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Brick work using common burnt clay building bricks in foundation and plinth in :-Cement Mortar 1:4 (1 Cement : 4 Sand) Second Class Bricks.

Brick work using common burnt clay building bricks in Super-structure above plinth level upto floor two level (Second Class Bricks) :-Cement Mortar 1:4 (1 Cement : 4 Sand).

Half brick masonry in common burnt clay building bricks in :- : Cement mortar 1:4 (1 cement:4 sand).

Half Brick thick honey comb brick work with common burnt clay building bricks in cement mortar 1:4 (1 Cement : 4 Sand) -Second Class Bricks.

6mm Cement plaster to ceiling In Cement mortar 1:3(1 Cement:3 Sand)

10mm cement plaster in single coat on fair side of brick/concrete walls for internal plastering upto floor two level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement mortar 1:4 (1 cement:4 sand).

15mm Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement Mortar 1:4 (1Cement:4 Sand).

Providing throating or plaster drip and moulding to R.C.C. Chajja

Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm nominal size)laid in one layer finished with a floating coat of neat Cement. (50mm thick)

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble: Area of slab over 0.50 sqm.

Providing and fixing angle iron door, window, clerestory window frame manufactured from M.S. Angle iron section of 50X50X6 mm ,thickness including hinges jamb, lock jamb, beed and if required angle thrashold of mild steel angle 50X25 mm welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including steel butt hinges 2.5 mm thick with provision for locking arrangement and shock observer as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-in-Charge.

Steel work welded in built up sections, trusses and framed work, including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint: In beams joists channels ,angles, tee ,flats with connecting plates or angle cleats as in main and cross beams, hip and jack rafters, purlins connected to common rafters and the like.

Providing and fixing flush door shutters core of black board construction with frame of first class hard wood and well matched first class Indian teak ply veneering with vertical grains of cross band and face veneers on one face and commercial ply veneering with vertical grains of cross band on other face of shutters.: 35 mm thick including black enamelled M.S. butt hinges.

Providing and fixing flush door shutters core of black board construction with frame of first class hard wood and well matched first class Indian teak ply veneering with vertical grains of cross band and face veneers on one face and commercial ply veneering with vertical grains of cross band on other face of shutters.: 25mm thick including black enamelled M.S. butt hinges.

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws. 35mm thick 2nd class deodar wood.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestory windows including bright finished black enamelled iron hinges with necessary screws. 30mm thick 2nd class deodar wood.

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete : 25 mm dia

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : 20 mm dia

Grading roof for water treatment with Cement concrete 1:2:4 (1 cement :2 sand 4 graded stone aggregate 20 mm nominal size ).

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominal size).

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces(two coats)to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter) sand papering and knotting. Ready mixed paint brushing wood primer pink.

Painting two coats (excluding coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt, dust and other foreign matter, sand papering & stoping With white enamel paint.

Painting two costs (excluding priming cost on new steel and other metal surfaces with enamel paint brushin to give an even shade including cleaning the surface of all dirt, dust and other foreign matters :-- Enamel paint other than white :--

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. Complete: 300x16mm.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. Complete: 250x16mm

Providing and fixing aluminium tower bolts (barrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete. 100x10mm

Providing and fixing aluminium tower bolts (barrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete. 150x10mm

Providing and fixing aluminium tower bolts (barrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete. 200x10mm

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete. 100 mm.

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete. 125 mm.

Providing and fixing M.S. hooks and eyes. 150 mm

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. Complete. Double strip (horizontal type).

Providing and fixing 100mm bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete.

Providing and fixing bright finished or/and black enamelled iron (Helical door spring 150mm)

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour: 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes: 110mm diameter.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion: Bend 87.5° (110 mm bend).

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. ( Internal work ):15mm nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. ( Internal work ): 20mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 20 mm nominal bore.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm diameter

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required: (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board. (610x460 mm bowl depth 200 mm)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe : 32mm dia.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe : 40mm dia.

Providing and fixing CP Brass Single lever non-telephonic wall mixer of quality & make as approved by Engineer in charge-15MM nominal diameter.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing toilet paper holder : C.P. Brass.

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length : 15 mm nominal bore.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing soil, waste and vent pipes. 75 mm diameter : Sand cast iron S&S pipe as per IS: 1729

Providing and fixing soil, waste and vent pipes. 100 mm diameter : Sand cast iron S&S pipe as per IS: 1729

Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter. 75mm nominal diameter/size pipe

Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter. 100mm nominal diameter/size pipe

Providing and fixing plain bend of required degree: 75 mm dia, Sand cast iron S&S as per IS - 1729

Providing and fixing plain bend of required degree: 100 mm dia, Sand cast iron S&S as per IS - 1729

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 75x75x75 mm, Sand cast iron S&S as per IS - 1729

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100x100x100 mm Sand cast iron S&S as per IS - 1729

Providing and fixing terminal guard. 75 mm, sand cast iron S&S as per IS - 1729

Providing and fixing terminal guard. 100 mm, sand cast iron S&S as per IS - 1729

Providing lead caulked joints to sand cast iron / centrifugal cast (Spun) iron pipes and fitting of diameter 100MM.

Providing lead caulked joints to sand cast iron / centrifugally cast (Spun) iron pipes and fitting of diameter 75 MM.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: 100 mm inlet and 75 mm outlet. ( Sand Cast Iron S&S as per IS- 1729).

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end)-20mm nominal bore.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in charge.

Providing weapholes in brick masonry / stone masonry /plain reinforced concrete abutment, wing wall, return wall with 100 mm dia PVC pipe extending through the full with of the structures with slop of 1(v):20(H) towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3.7

Narain Singh Thakur

ARCTURUS ENGINEERING PRIVATE LIMITED