CONSTRUCTION OF NAVEEN RAJKIYA HIGH SCHOOL AT KEALADEVI (MUJAHIDPUR), BLOCK PANWASA IN DISTRICT SAMBHAL (U.P.)

Civil works

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 100 mm dia

In all kind of soil upto 1.5m to 3.0m. depth

In all kind of soil upto 3.0m to 4.5m. depth

Sand filling in plinth including supply of necessary quantity of sand from a distance not excluding 8km from the site of work and including watering dressing etc. rate to include cost of all materials, labour and T&P etc.required for proper completion of the work.

Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 stone grit 40 mm nominal size) and curing complete,including cost of form- work,in foundation and floors.

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. 6XLWDEOH M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 450 lpm at 35 m Head

Earth work in excavation in trenches for foundations and pipes c

ables etc in ordinary soil (loan clay or sand) including lift upto 1.5 m, lead upto 50 m and dressing of sides and ramming of bottom and disposal of surplus excavated earth as directed by the Engineer- in- charge with in a lead of 50m .

Filling of carted earth up to 5 km i/c levelling watering compacted, loading & unloading

Providing and injecting chemical emulsion for antitermite treatment and creating a chemical barrier under and alround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the the external perimeter of binding expansion joints, surrounding of pipes and conduits etc, complete (plinth area of the building at ground floor only shall be measured as per I.S.6313 (PartII 1981) Alderine emulsifiable concentrate or any other approved material such as Heptrachlor or Chlordane will be used. The rate of application of chemical emulsion shall be as follows: (1) Treatment for masonary & foundation 5 liters per sqm. (2) Back fill in immediate contact with foundation 7.5 liters/sqm (3) Treatment of top surface of plinth filling 5 liters/sqm (4)Treatment junction of wall and the floor 7.5 liters /sqm (5) Treatment of soil along external perimeter of building 5 liters/sqm

R.C.C. work with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 (M-20) in lintels of doors and windows excluding supply of reinforcement and its binding but B.W.G.G.I. binding wire and including necessary centering and shuttering etc. and also including supply of all materials, labour and T & P etc.required for proper completion of the work.

Class 150 brick work in 1:6 cement and coarse sand of 2.25 fineness modulus mortar in foundation and plinth including supply of all materials, labour and tools and plants etc. required for proper completion of the work.

Class 150 brick work in 1:6 cement and coarse sand of 2.25 fineness modulus mortar in super-structure above plinth level up to floor two level ( up to two storeys ) including necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than 12cms.including supply of all materials, labour and tools and plants etc. required for proper completion of the work.

Class 150 brick work in 1:4 cement and coarse sand of 2.25 fineness modulus mortar in foundation and plinth including supply of all materials, labour and tools and plants etc. required for proper completion of the work.

Class 150 brick work in 1:4 cement and coarse sand mortar in superstructure for wall thickness 12 cms & below.including supply of all materials, labour and tools and plants etc. required for proper completion of the work.

Painting on D.P.C. with two coats of airblown bitumen 85/50 or 85/25 @ 1.7 kg/sqm approx. including cost of fuel if any.

Providing and laying "brick coba" 12mm thick laid with M-150 class brick bat coba 7.50 cm thick with gap of 15mm to each other, over 20mm thick base of cement mortar 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with aerelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compound in 1:4 cement and coarse sand mortar finished smooth & top mashed false square 30cm x cm and side wall parapet shall be mono tythic plaster wall upto 30 cm higher and junction and corner shall be rounded by brick ballast cement and coarse sand masonary Coba with top finished plaster mixed with acetic water proofing compound @ 2% by weight & including S/o all material, labour, T&P etc complete for proper completion of work.

Supply and fixing of flush door commercial quality conforming to IS : 2202 (Part I) including fixing of wooden cleats and stopper core and including fixing and adjestment of hings bolts locks handle spring fitting with necessary screw to be supplied. 32 mm thick

Add extra for Double Leaf

Mild steel or iron work of small sizes and sections such and holding down bolts, hold fast tierods,gratings etc. ( when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. Fabrication of hold fast for door chaukhats and windows.

Mild steel or iron work of small sizes and sections such and holding down bolts, hold fast tierods,gratings etc. ( when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. Fabrication of grill / stairs case railing.

Mild steel or iron work of small sizes and sections such and holding down bolts, hold fast tierods,gratings etc. ( when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. Fabrication of Z-section steel windows.

Mild steel or iron work of small sizes and sections such and holding down bolts, hold fast tierods,gratings etc. ( when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. Angle iron door chaukhats .40*40*5

Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in anover all rates ) wrought to required shape as necessary including bending for proper completion of the work and i

ncluding supply of steel and wastage and over lapping and hookes.

15 mm cement plaster on plinth side of single or half brick wall 1 cement : 3 Course sand

12 mm cement plaster in single coat on fair side of single or half brick wall for interior plastering up to floor two level including brick wall for interior plastering upto floor two level including internal rounded angles chamfers, and / or rounded angles not exceeding 80 mm in girth and finished even and smooth No. extra for mixing any additive. (1)1 cement : 6 Course sand

12 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1)1 cement : 6 Course sand.

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the plastered surface as per approved pattern using wooden battens nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in- Charge.

R.C.C. work with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 (M-20) in slab excluding supply of reinforcement and its binding but B.W.G.G.I. binding wire and including necessary centering and shuttering etc. and also including supply of all materials, labour and T & P etc.required for proper completion of the work.

R.C.C. work with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 (M-20) in beams excluding supply of reinforcement and its binding but B.W.G.G.I. binding wire and including necessary centering and shuttering etc. and also including supply of all materials, labour and T & P etc.required for proper completion of the work.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 25 mm thick with 20 mm nominal size stone aggregate

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 3 (1 cement : 3 coarse sand) 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete

R.C.C. work with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 (M-20) in raft foundation and footing excluding supply of reinforcement and its binding but B.W.G.G.I. binding wire and including necessary centering and shuttering etc. and also including supply of all materials, labour and T & P etc.required for proper completion of the work.

R.C.C. work with cement approved coarse sand and 2 cm. (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 (M-20) in column excluding supply of reinforcement and its binding but B.W.G.G.I. binding wire and including necessary centering and shuttering etc. and also including supply of all materials, labour and T & P etc.required for proper completion of the work.

Supply and fixing 6 mm. (¼") China white glazed tiles in flooring or in skirting or dado laid with 1:3 Cement and approved coarse sand mortar finished with white cement slurry, jointing and polishing complete, including supply of all materials, labour and Tools and Plants.

Providing and laying Vitrified floor tiles in different sizes (thickness 8mm), with a water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in desired colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand ) including grouting of joints with white cement and matching pigment etc. complete.(600x600mm)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Providing and laying 6 to 8mm thick ovory or light shade Vitrified tiles in different sizes with a water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in desired colours and shades, laid on 20mm thick cement mortar 1:3 (1 cement :3 coarse sand ) including grouting of joints with white cement and matching pigment etc. complete. (Skirting)

Providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Painting two coat over priming coat (but excluding cost of priming coat) on steel and other metal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as LUXOL3,Hi-gloss apcolite superlac, DULUX specified brushing to give an even shade and including cleaning the surface of all dirt,dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work.

Providing and fixing stainless steel sliding door bolts, ISI marked to required colour or shade, with nuts and screws etc. complete: 300x16 mm

Providing and fixing stainless steel handles, ISI marked, to required colour or shade, with necessary screws etc. complete : 125 mm

Painting two coat over priming coat (but excluding cost of priming coat) on wood surface and other metal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as LUXOL3,Hi-gloss apcolite superlac, DULUX specified brushing to give an even shade and including cleaning the surface of all dirt,dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work .

Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material &sand papered smooth including cost of all materials.

Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete

Providing & fixing glass panes with putty in steel doors, windows, clerestory windows, all complete with : 3.8 to 4.7 mm thick glass panes

Providing and fixing stainless steel tower bolts, ISI marked, to required colour or shade, with necessary screws etc. complete 200x10 mm

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality.M.D. -10- Circular shape 500mm internal diameter

Providing & Fixing 75mm plane sand cast iron S&S bend of required drgtee.

Wiring point for light in PVC conduit with 1.5 sq.mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SWG copper earth continuity wire,GP Box, piano type switch & ceiling rose/angle/batten holder on 3mm thick phenolic paminated backalite sheet etc complete in all respect as directed including matching colour wash

Wiring point for fan / fresh air fan (light duty exhaust fan) in PVC conduit with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit. partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, completewith 14 SWG copper earth continuity wire,GP Box , piano type switch & ceiling rose on 3 mm. thick backelite sheet etc., complete in all respect including matching colour wash.

Wiring point for plug in PVC conduit with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit. partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with14 SWG copper earth continuity wire and piano type switch and socket etc., complete in all respect including matching colour wash.

Supply of 20mm ball valve

Supply of 20mm G.I. Nipple

Wiring point for call bell in PVC conduit with 1.5 sq.mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting complete with 14 SWG copper earth continuity wire GP Box and piano type bell push or 2 pin socket etc, complete in all respect including matching colour wash.

Add for light / fan points with modular type switch in place of piano type switch.

Supply and fixing of power plug with 15A/250 volt flush type switch and 5 pin 15A/250V flush type universal socket in suitable M.S. box of 175mm x 100mm x 50mm size with phenolic laminated bakelite sheet cover 3mm thick fixed with brass machine screw and cup washer.

Supply & wiring of sub main FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable heavy duty PVC conduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting, including matching colour wash etc complete in all respects. 2 nos. 1.5 sq. mm. with 1 no 14 SWG copper earth continuity wire, in 25 mm dia conduit.

1 x 4 sq. mm. with 1 no 14 SWG copper earth continuity wire, in 25 mm dia conduit.

2 x 4 sq. mm. with 2 no 14 SWG copper earth continuity wire, in 32 mm dia conduit.

2 x 6 sq. mm. with 2 no 10 SWG copper earth continuity wire, in 32 mm dia conduit.

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 voltes grade.16 sqm .mm 4 core.

Supply and fixing and concealing of PVC conduit pipe with ISI mark embossed and with PVC accessories confirming to IS No. 3419 for drawing wires duly sealed at joints with original resin / adhesive to make the complete piping rigid, plastering with cement sand mortar finished to the level with matching colour wash including cost of all material labour and T&P etc required for proper completion of the work as per directions and to the satisfaction of Engineer in charge. 20 mm dia. 2mm thick

S/F of surface / flush mounting SPN Distribution board without MCB complete in all respects as directed at site by Engineer-in-charge. 8 WAYS

Add for plug point with modular switch & socket in place of piano type switch & socket

Add for call bell point with modular type bell push in place of piano type bell push

S/F of surface/flush mounting TPN distribution board without MCB complete in all respect as directed at site by Engineer-in-charge. (Cat-A) 4 WAYS

Supply Fixing and making commection of 30 MA E.L.C.B. (Earth leakage circuit breaker) of din/R.C.C.B. rail mounting complete in all respects as per direction and satisfaction of engineer-in-charge. 25 Amp 4 Pole

Supply & fixing of power plug with 20A/250 volts flush type modular switch and 5 pin 20 A/250 volts flush type universal modular socket on concealed MS box including supply of all material, labour T&P etc. required for proper completion of the work

Supplying & Laying of 25mmx3mm G.I. Strip for earthing purpose as required complete in all respects.

Supply & fixing of two number 8 SWG G.I. wire for earthing purpose as required complete in all respects.

40 Amp 4 Pole

S/F of led Tube Light with batten suitable for up to 1x22 watt LED tube light fitting including tube on surface complete in all respect. Category AAA

S/F of led Tube Light with batten suitable for up to 2x22 watt LED tube light fitting including tube on surface complete in all respect. Category AAA

Supply and fixing of batten / angle holder complete in all respect

Supply & fixing of 6/10/16/20/25/32 amp. SP MCB (10 KA) Cat-A

S/F of 40 Amp DP MCB (10 KA)

Supply and fixing of recess/ Surface/ Pendent mounting round 10 to 15 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. CAT- AAA

Supply & burrying of 600mm x 600mm x 6.0mm G.I. plate, vertically for earthing with its top at least 3 m below ground level complete 20mm dia. G.I.pipe and funnel for watering and one earthing lead of no. 8 SWG G.I. wire in 15 mm dia. GI pipe upto switch board (from apron to switch board the cost of GI pipe & GI wire will be extra) 300mm square C.I. box with hinged cover, masonary housing alternate layer of charcoal/coke and salt atleast 150mm thick alround etc. as per the direction of engineer in-charge complete in all respect .

Erection and testing of ceiling fan and regulator for room height upto 3.50 meter including supply of 3 mm thick G.I. Rod 19 mm dia. Duly painted, complete in all respect.

Erection and testing of exhaust fan on the existing hole with suitable size of rag bolts nuts and washers etc complete in all respects.

S/F of hexagonal fan box with hexagonal side of approx. 80 mm.in length fabricated from 16 SWG M.S. sheet incorporating with 10 mm. dia. M.S. round bar duly bent for supporting fan hanger duly painted with red oxide and screwing arrangement with wiring conduit laid in the R.C.C. roof before concreting along with supply of all materials, labour, T&P etc. for proper completion of work.

Making hole in the wall for exhaust fan and fini

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).

shing properly complete in all respect.

Supply of Ceiling fans with fan moter of AC permanent insulation , capacitor rating to conforming BEE 5 star rating & IS 374/79 and aslo comply with IS: 1709/1984 with latest amendment . The rated Voltage 220/240 Volts, 50 Hz I-ph AC assemble should consists of down rod, blades, shackle canopies etc. and wih double ball bearing system . BEE 5 Star Rated - 1200mm sweep

Providing M.S. foot rests including fixing with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design With 20x20 mm square bar

Supply and Fixing of LED bulb 9 watt

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require a) White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap.

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm

Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. Semi rigid pipe a) 32mm dia

b) 40mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing soil, waste and vent pipes:75 mm diameter Sand cast iron S&S pipe.

Providing lead caulked joints to sand cast iron/ cetrifugally cast (squn) irons pipes & fitting of 75 mm dia

Providing and fixing CP Brass Single lever lelephonic wall mixture of quality & make and as per thedirection of Enginer-in-charge. a) 15mm dia nominal dia.

Supply of AC 230/250 Volts, 50 Hz exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required 300mm sweep.

Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 meter long with S.S. triangular plate for Eureopean type W.C. of quality and make as approved by engineer-in-charge. 15mm nominal bore

Same as above but for European type W.C. pan with white plastic seat and lid.

Providing and Fixing C.P. brass Ablution health faucet assembly with 1.0 m long braided PVC hose with mounting bracket fixed on wall complete.[FOR EWC]

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes. a) 110mm diameter

Providing and fixing C.P. brass Two-way angle valve for EWC points & for fixing Ablution Health Faucet of approved quality conforming to IS:8931. 15 mm nominal bore

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and making and finishing the outlet complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. a) 110mm

Providing and fixing in floor and wall face Ringfit UPVC ASTRAL ULTRADRAIN Conventional system for soil and waste water pipes conforming to Type B including jointing with seal ring. (i) Double socketed pipes.a) 110mm dia P.V.C. pipe

b) 90mm dia P.V.C. pipe

Bend 110 mm

Providing & fixing G.I. pipes complete with G.I. fittings & clamps including cutting & making good the walls etc. (internal work) Exposed on wall a) 32mm dia nominal bore (medium duty)

Painting G.I. pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work. a) 32mm dia nominal bore.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (internal work) Exposed on wall a) 25mm dia nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. a) 15mm dia nominal outer dia pipes

Providing & fixing UPVC Floor trap of self cleansing design with CP Jali complete in all respects. P-Trap type Floor Trap 110 x 90 mm

Providing and fixing

on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Door Tee 110x110x110 mm

b) 20mm dia nominal outer dia pipes

c) 25mm dia nominal outer dia pipes

Providing and fixing gun metal gate valve with wheel of approved quality. a) 25mm dia nominal bore

b) 32mm dia nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete a) 25 mm nominal bore

110x110x90 mm door tee

90 mm bend

Providing & fixing CP brass bib cock of approved quality conforming to 15mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. a) Circular Tank

Excavating trenches in all kind of soil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. up to 1.50 m depth Pipes 80 mm to 300 mm diameter

Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 15mm nominal bore

Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to 15mm nominal bore

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarase sand of size range 1.5 mm to 2mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Providing and fixing in floor and wall face Ringfit UPVC ULTRADRAIN Conventional system for soil and waste water pipes conforming to Type B including jointing with seal ring. (i) Double socketed pipes. 160mm dia Under floor (for External sewer)

Constructing brick masonry manhole with F.P.S. bricks in cement mortar 1 : 4 (1 cement : 4 coarse sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 grade stone aggregate 20mm nominal size); foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1cement 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finishd with a floating coat of neat cement complete as per standard design Inside size 90 x 80 cm & 45 cm deep

Providing and fixing square mouth S.W. Gully trap grade `A' complete with C.I. grating brick masonry chamber with F.P.S bricks and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 180 x 150 mm. size P type

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supply & installation of india marka - ii Hand pump with Boring 150 MM dia .60.00 mtr deep,110 mm dia p.v.c casing pipe and const of c.c. 1:2:4 circular plate form complete

Supplying, installation, testing and commissioning of Sector panel suitable for following zones,complete with visual indications for short circuit fault,open cricuit fault fire condition zone covered,complete with all connections,interconnections as required. 6 Zone

Supplying, installation, testing & commissioning of addressable manual call point complete as required

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.

Supplying, installation, testing & commisssioning of ceiling/wall mounted loud speaker, 3/1.5 watt in ABS enclosure complete as required

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheathcomplete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. Speaker cable Four pair, 2 core, 1.5 sqmm.

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Gravel packing in tubewell construction in accordance including providing gravel fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction of Engineer-in-charge.

Constructing brick masonry manhole with 75 class designation F.P.S. bricks in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand: 4graded stone aggregate 20mm nominal size); foundation concrete 1:4:8 mix (1 cement :4 coarse sand: 8 graded stone aggregate 40mm nominal size) inside plasstering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design. a) Inside size 60x60 cm & 90 cm deep

Supply & fixing of fire extinguishers, ABC type 6.00 Kg capacity complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Supply of 1.5HP Submersible pump

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous unmetal/ Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/ gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & anding valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

Supplying and fixing of Self Glow Exit signage for stairs and exits size 100 x 300.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing weather proof standard hose cabinet (900mm x 750 mm x 400 mm) out door type suitable for accommodating yard hydrants made of 1.5mm thick M.S. sheet having central opening glazed door including necessary locking arrangements, painting one coat of primer and two coats of postal red enamel paint

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone ggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed , including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-incharge, upto 90 metre depth below ground level. Drilling of 300mm dia bore hole manually.

and housing 2 Nos. canvas hose pipe and branch pipe as required. (The cabinet shall be floor mounted on suitable raised platform). The shutters are to be lockable type. The words “Fire Hose Cabinet” to be painted on the box.

Providing and fixing Fire hose cabinet glazed door shutter and frame with hold fasts ( frame fabricated from 40 x 40 x 5mm and shutter from 35x35x5mm M.S. angle) 1500 mm high x 1000 mm wide with locking arrangement, 4mm thick glass with M.S. flats including all accessories, painting with one coat of steel primer and two coats of postal red enamel paint. The words “Fire Hose Cabinet” to be painted on the box.

Providing and fixing air release valve.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having CBR Value-20

Supply & Fixing 80 mm thick Precast cement concrete I-Shape interlocking paver block a with top layer of minimum 8 mm thickness having plan dimension 200x(160+120mm) of O.P. cement, Smooth high gloss finish skid reditant manufactured from rubber moulds through vibro-compression machanism. the compressive strength of concrere paver block shall not be less Than 30MPA ((M-30) AND wight 5kg per no confirming to IS;15658-2006 with a 4 cm thick layer of fine sand including cost of material,labour, T& p TAXES etc. requried for proper completion of the work as directed by Enginner-in-charge. (I)Grey color

Drilling of 200 mm dia bore hole.

Lowering of 110 mm dia blue casing pipe.

Development of tubewell

Installation of pump 1.5 HP

Shifting of Machine of boring

Supply of Blue casing pipe 110mm

Supply of Blue casing ripped screen 110mm

Supply of P.V.C. end cap 110mm

Supply of P.V.C. dori

Supply of 32mm G.I. pipe

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia

Supply of M.S. Socket 32mm

Supply of Boring cover 100mm

Supply of Clamp 32mm

Supply of control panel 1.5 /1.0 H.P.

Supply of 4.00sqmm cable

Add GST as per Applicable