SPECIAL REPAIR TO BUILDING NO NP-10 UNDER GE (SOUTH) MAMUN AT MAMUN MIL STN

Amount

Taking down chowkhats or frames of any description not exc 1.50 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware , complete all as specified and directed.

Taking down chowkhats or frames of any description exc. 1.50 Sqm and n.exc 4.00 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware complete all as specified and directed.

Taking down Shutters of any description exc 1 sqm and nexc 2 sqm each including builders hardware complete all as specified and directed.

Taking down Shutters of any description exc 1 sqm and nexc 2 sqm each including refixing in same opening after repair complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons laid bedded and pointed pointed in any in anymortar complete all as specified and directed.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for pressed steel frames 125mmx60mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface complete all as specified and directed.

M&L for pressed steel frames 105mmx60mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface complete all as specified and directed.

M&L for Solid PVC Door Frame of size 75mm x 45mm (suitable for moulded door) made out of 5mm wood grain printed PVC sheets & edges will be painted to match printed sheet as reinforced with 19mm square MS tube and fixing in opening as specification & drawing complete all as specified and directed.

S&F in repairs CP soap nich fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed.

M&L for 35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12mm veneered particle board with commercial veneering on both faceS ,The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated, fitted to chowkhats incl 02 coats of synthetic enamel paint over a coat of pink primer after preparation of surfaces complete all as specified and directed.

M&L for 35mm thick glazed and skeleton shutters (Factory made) of 2nd class hard wood and prepared to receive glass or gauge etc with rounded, chamfered or mitred sash bars edges of framing plain chamfered or rounded fitted with cut and mitred beads and fitted to chowkats for securing glass/gauge, size of stiles rails and other parts as per clause 8.20 (a) of SSR Part-I 2009 (Larger size to be provided) incl 02 coats of synthetic enamel paint over a coat of pink primer after preparation of surfaces complete all as specified and directed.

M&L for Factory made solid pannel PVC door shutter (Wood grain colour sheets on both sides) 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded wood grain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour & as gap insert for top rail & bottom rail Panelling of wood grain colour sheet to be fitted in MS frame welded / sealed to stiles & rails with suitable PVC sheet beading and joined together with solvent cment, supplying & fixing in the frame complete all as specified and directed.

M&L for Box type Steel windows and ventilators comprised of tubular frame and shutters made out of 1.25mm thick M S sheet tube factory made with double side hung wire gauged shutter & glass/glazed shutter (wire cloth and glass panes only shall be measured and paid separately) with steel handle and steel peg stay dovetailed or welded incl 2 Nos. tower bolts 150mm long for each leaf and 10mm square bar grills at spacing as shown on drg, welded to F I frame work, including other fittings; hinges, handles, tarred hold fasts fixed in PCC blocks all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for 3 mm thick sheet glass ordinary quality and glazing with oil putty or fixed with beads/ glazing pins not .exc 0.5sqm in each pane complete all as specified and directed.

S&F Continuous (piano) hinges,width of flaps (when open) 40 mm mild steel, bright finish or electrogalvanisedfixed in repairs complete all as specified and directed.

M&L for Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or galvanized wire staple complete all as specified and directed.

M&L for Aluminium anodised barrel tower bolt, extruded section 200mm long , complete all as specified and directed.

M&L for Aluminium anodised handle, extruded section of size 100 mm complete all as specified and directed.

M&L for Aluminium anodised handle, extruded section of size 125 mm complete all as specified and directed.

S&F Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

M & L for 50mm dia, polished, hard wood knobs fixed with screws complete all as specified and directed.

S&F Hasp and staple aluminium anodized 100mm long including bolt to hinge plate and fixed with screws complete all as specified and directed.

M&L for 300 mm aluminium alloy sliding door bolt with hasp & staple (bolt type) and fixing clip of sheets cast or extruded section and fixing sliding bolt of extruded section complete all as specified and directed.

M&L for Bitumen blown any grade, applied hot, two coats, to concrete surfaces at the rate of 1.5kg. per sq. m per coat & applying Polythene film, black, 50micron laid in sunken slab and embedded in side wall/covet fillet complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-1 using 20mm graded crushed stone aggregate as in plinth protection laid in slope finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio (1:2) by weight including dismantling existing floor of any type and pattern and removal of rubbish out off the premises complete all as specified and directed.

M&L for 60mm thick factory made rubberised coloured (laminated) interlocking paver block (using vibro compaction method) (topping thickness not less than 5mm) in white cement and non fadable glossy pigment of approved shade of any shape and size conforming to IS-15658-2006 of M-35 grade laid over & including cleaned dry sand cushion 50mm thick over and including 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) over and including 50mm thick sand cushioning complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick of size as directed over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed

M&L for Machine cut kota stone slab 18-20 mm thick in single piece as directed in stairs / step / window cills over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over and including 10mm thick screed bed or bedding layer of cement mortar (1:4) complete all as specified and directed

M&L for Cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregates) kneelers, apex stones, bed plates, kerbs, benching, coping, Bed blocks and the like, rounded or chamfered on edges including necessary formwork complete all as specified and directed.

M&L for Non-skid ceramic coloured rectified edges joint free tiles 8mm thick area of each tile exceeding 0.18Sqm but not exceeding 0.38 Sqm as in floors etc, set & jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed.

M&L for Non-skid ceramic coloured rectified edges joint free tiles 8mm thick as in floor area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors etc, set & jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:6) including taking out cement plaster sweeping clean & washing down with water to remove dust complete all as specified and directed.

M&L for Marble Green/Bhaislana Zebra 18 to 20mm thick (table rubbed and premirror polished) in single piece in steps, jambs, pillars, window-cills, cooking platforms and like set and jointed in neat cement slurry including pointing in epoxy grout to match marble shade, including making 25 mm dia hole for gas pipe including rounding the edges of marble stone , laid over and including 15mm thick screed bed in CM 1:4 dismantling of existing tiles/stone etc complete all as specified and directed.

M&L for Glazed ceramic (coloured) tiles 7mm thick, of size 450mmx300mm on vertical surfaces such as in dado etc, set and jointed in neat cement slurry and pointed in coloured epoxy grout to match tiles over and including 10mm thick backing coat in cement mortar (1:4), surface finished even and rough to receive tiles, including dismantling existing tiles of any type and pattern including cement mortar backing coat and removal of rubbish out off the premises complete all as specified and directed.

S&F in repair 15mm bore Stop valves fancy type, chromium plated cast copper alloy long shank and exposed part kit with fitting sleeve, operarting lever & adjustable wall flange (concealed type) screwed both ends for iron pipe or for unions complete all as specified and directed. Make : Jaquar Cat part No CON-083FT & CON-083FTK or equivalent of Hindware/Marc.

S&F 15 mm bore Stop valves/Angle valve cast copper alloy, chromium plated (ISI marked) , screwed down,high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and directed.

S&F in repair for single towel rail brass chromium plated 600mm long fixed with chromium plated screw and PVC cleat complete all as specified and directed. Make : Cat part No AQN-7711 of Jaquar or equivalent model in Hindware/Marc.

S&F in repair Brass Chromium Plated shower rose with arms fancy type with swivel joints 75 mm face dia of appoved make and cat part for 15mm bore iron pipes complete all as specified and directed. Make : Prayag Cat part No BS-73 or equivalent model in Hindware/Marc.

S&F Peg set of six, powder coated fixed with chromium plated brass screws and wooden & plastic cleats (minimum weight 190 grams) complete all as specified and directed.

Supply and fixing factory made 18mm (+0.7mm) thick PVC sheet one side prelam sheet for cupboard shutter of density 600kg/Cbm bent 90o and finish at all edges at level for making edges at level for making edge lipping/benching or 0.5mm thick PVC sheet lipping at 4 edges using bonding tape, complete as per direction of Engr-in-Charge & as per Manufacture specification & recommendation.

S&F in repair for 15mm bore bib taps fancy type with wall flange, chromium plated cast copper alloy long body with capstan heads, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repair for Rotational moulded polyethylene water storage tanks three layer of capacity 1000 litre, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm ball valve high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and dismantling of existing PVC tank of any capacity, complete all as specified & directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed. Make:Paryag/Polytech

Taking up or down 15mm bore pipe and connections including cleaning for refixing including all new fittings for 15mm bore complete all as specified & directed.

Taking up or down 20mm bore pipe and connections including cleaning for refixing including all new fittings for 20mm bore complete all as specified & directed.

M&L for GI water tubing surface/concealed, 15mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Refixing of old steel tubing 15mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) fixed to wall , floor etc complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc, and making good, cutting not exc 10 cm girth complete all as specified & directed.

M&L for GI water tubing surface/concealed, 20mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Refixing of old steel tubing 20 mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) fixed to wall , floor etc complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

M&L for GI water tubing 50mm bore, medium grade galvanized as in short length as spout pipe in brick wall complete all as specified and directed.

S&F in repair for 25mm bore Mild steel powder coated, single curtain rod (wall thickness not less than 1mm) including fancy type PVC brackets of approved design/pattern, funnels etc suitable for single curtain rod complete all as specified and approved by GE.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc and removal of rubbish out off the premises complete all as specified and directed.

M&L for Brick work with Fly Ash Brick (Non-Modular) straight or curved on plan to any radius built in CM 1:6 complete all as specified and directed.

M&L for Brick work with Fly Ash Brick (Non-Modular) straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.

Taking down cement or cement lime plaster of any description and removal of rubbish out off the premises, complete all as specified & directed.

M&L for rendering 5mm thick cement plaster on surfaces of concrete ceiling in cement mortar 1:3, surface finished even and smooth using extra cement complete all as specified & directed.

M&L for Rendering 15mm thick in two layers [base layer 10mm in 1: 6 & finishing layer 5mm thick in cement mortar (1:4)] using liquid water proofing compound in IInd layer only on brick work or concrete surfaces of wall, surfaces finished even and smooth using extra cement complete all as specified & directed. (Note : WPC shall be measured and paid separately)

M&L for rendering 10mm thick on brick work or concrete surface in CM (1:6) on wall surfaces finished even and smooth using extra cement complete all as specified & directed.

M&L for rendering 10mm thick on brick work or concrete surface in CM (1:3) on in fasia /edges/ ceiling of chajjas/ roof projections etc including taking out peeled off plaster / concrete and making the line in true shape and finishing the surfaces finished even and smooth using extra cement complete all as specified & directed.

Supply and fixing "Rajshri/Accucel/Plasopan" brand factory made PVC door/Cupboard frame (prelam) - of size 115mm x 50mm with a wall thickness of 5mm, made by joining 3 Nos heat bent 'C' chennel of 5mm PVC sheet density 600kg/Cbm manufactured by ISO 9001-2008 certified company of size 35mm x 35mm x 35mm and 50mm x 45mm x 50mm and 35mm x 35mm x 35mm using solvent cement. The two side 'C' channel shall be reinforced with 19mm x 19mm M.S square tube of 19 gauge. All three 'C' channel shall be fixed to flat base of 5mm PVC sheet with solvent cement. The door frame shall be mitre cut to two corners and jointed by insert 4 No 150mm long brackets of 15mm x 15mm M.S square tube inside the 19mm x 19mm square tube. The door frame shall be fixed to the wall using 65/100mm long MS screws through the frame by using PVC fasterner. A minimum of 4 Nos of screw to be provided for each vertical member and minimum 2 Nos for horizontal member etc. Complete as per direction of Engr-in-Charge, Manufacturer's specification and drawing.

M & L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sqm of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete complete all as specified and directed.

M & L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

S&F Magnet ball catcher for cupboard shutter, complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in sub base laid in slope including making kerbs along the walls, junctions (average thickness 7cm) finished even and smooth using water proofing compound (liquid) as in sunken portion complete all as specified and directed.

M&L for 20 mm bore gun metal gate valve, with cast iron wheel head, screwed both ends for GI pipe, fixed in repair, etc complete all as specified and directed.

S&F in repair for Vitreous china White Squatting Orissa Pattern pan of size 580x440mm, including cast iron ‘P’ trap, front or back inlet and integral foot rests and making connection to trap and to flushing pipe, anti syphonic pipe complete all as specified and directed. (Note : Demolition and refilling of concrete PCC 1:5:10 type E-2 in sunken portion shall be measured & paid separately.)

S&F in repair PVC flushing cistern dual flush type 10 Ltr capacity, valve-less syphonic action type, low level, complete with inlet, ball valve, handle, including brackets/pins, PVC flush pipe 32mm bore and PVC connection 15mm bore 450mm long complete all as specified and directed.

M&L for Vitreous china wash hand basin, white, flat back, size 550x400mm (Make : Jaquar Cat part No CNS-WHT-801 or equivalent model in Hindware/Parryware/Somany) including 15mm bore fancy type Pillar taps, cast copper alloy, with long screwed shank and fly nuts, chromium plated (Make : Jainko Cat part No PCJ-1 or equivalent model in Hindware/Marc.) brackets, CP waste coupling, 32mm bore PVC waste pipe of min 600mm long & 15 mm bore PVC connections, including cutting for and pinning in end of brackets or erecting stand fixed in repairs complete all as specified and directed.

S&F in repair for Stainless steel sink with draining board 1mm thick sheet for kitchen with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm, including 32mm bore PVC waste outlet pipe of minimum length 600mm complete all as specified and directed. Make : Blue star Cat part No. BSSBSD-52 or equivalent model in Nirali/Jyoti

S&F Stainless steel plate rack of size 750x900mm fixed with chromium plated screw and PVC cleat complete all as specified and directed. Make : Blue star Cat part No. KPR-312 or equivalent model in Nirali /Jyoti

M&L for Filling of sunken floor with PCC 1:5:10 type D-2 using 40mm graded crushed stone aggregate complete all as specified and directed.

S&F rubber lining fitted with aluminium powder coated strip 100mm wide for door cill completed all as directed.

S&F in repair for 100 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with or without ears, laid in floor complete all as specified and directed.

S&F in repair for 75 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with or without ears, laid in floor complete all as specified and directed.

S&F 110 mm bore bends PVC (SWR) (any radius) fixed with cement solvent etc complete all as specified and directed.

S&F in repair for 100 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) complete all as specified and directed.

S&F in repair for 75 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) complete all as specified and directed.

S&F in repair for 100 mm bore, cast iron branch pieces or Tee, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access doors etc complete all as specified and directed.

S&F in repair for 75 mm bore, cast iron branch pieces or Tee, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access doors etc complete all as specified and directed.

S&F in repair for 75 mm Cast iron floor trap, with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repair 50 mm Cast iron cowl, fixed with cement joints complete all as specified and directed.

M&L for PVC (SWR) rain water pipes of 110 mm bore dia in any length, with rubber ring joints, fixed to walls with stack clamp made out of 25mm by 2 mm galvanised iron flat fixed with bolt and nuts, including taking down existing CI/SWR pipes etc complete all as specified & directed.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in roof padding finishing top surface even and smooth using extra cement complete all as specified and directed

M&L for 10mm thick in cement plaster in cement mortar 1:4 on concrete surface finished even and smooth using WPC liquid of make Dr. Fixit or STP as manufacturer instruction@ 0.200Ltr in 50Kg of cement complete all as specified and directed (Note : WPC shall measured and paid separately)

M&L for APP modified roof treatment over existing non-accessible RCC roof slab / chajjah / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specification complete all as directed :- (a) Cleaning existing surface properly. (b) Applying oil bound bitumen primer @ 0.30 liter/Sqm manufactured by the same agency as that of APP with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface. (c) Laying not less than 3mm thick APP modified water proofing membrane weighing not less than 3.60 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Laying of membrane, Physical property of membrane shall be as under :- (i) Membrane weight not less than 3.60 Kg/Sqm. (ii) Non woven polyester weight not less than 160 gsm/ Sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650/Sqcm and transverse not less than 450/sqcm at 230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation of reinforcement not less than 30%. (vii) Impermeability under water pressure not less than 3 Kg/Sqcm. (d) APP membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (e) Top of membrane shall be provide with solar reflective bituminous aluminum paint @ 0.1 Kg/Sqm as prescribed by manufacture of membrane.

M&L for preparation of newly plastered surfaces of wall & applying two coats of distemper oil emulsion (OBD) over and including a coat of primer as per manufacturer instructions (from same manufacturer of OBD) over and including a layer of wall care putty 2 mm thick complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint over and including a coat of primer as per manufacturer instructions complete all as specified and directed.

M&L for Preparation of existing distempered surfaces of walls by complete removal of existing treatment and apply two coats of distemper oil emulsion (OBD) over and including a coat of cement wall primer (from same manufacturer of OBD) over and including a layer of wall care putty not less than 3mm thick etc complete all as specified and directed.

M&L for Preparing new wall surface including making surface clean, and applying two coats of acrylic , antifungal emulsion exterior weather proof paint over and including a coat of primer as per manufacturer recommendation on external surfaces, complete all as specified & directed.

M&L preparation of old treated steel surfaces of any description over 10 cm in width or girth & applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of old treated wooden surfaces of any description over 10 cm in width or girth & applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and apply three coats of white wash on plastered surfaces complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and apply three coats of white wash on plastered surfaces complete all as specified and directed.

M&L for preparation of existing white washed surfaces of walls and apply two coats of white wash on plastered surfaces complete all as specified and directed.

M&L for preparation of existing white washed surfaces of ceiling and apply one coat of white wash on plastered surfaces complete all as specified and directed.

Supply only Polymer liquid water proofing compound of make Pidilite/Bauchemic/Fosrock, all as specified and directed.

Taking down carefully unserviciable/ damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets, Bracket /sketch fitting etc ) and removing material from site and making good to the disturbed surface to match with existing finish complete all as specified and directed.

M&L for Modular Point wiring using FRLS PVC insulated unsheathed /multi stranded copper conductor cable 1.5 sqmm including 1.5 Sqmm FRLS PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bends, junctions box and approved make sunken modular metal flush gang box and suitable support frame and cover plate (inner/outer) of required modules for mounting modular switches/ sockets etc, connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc (conduit shall be fixed on surface of ceiling with necessary saddles where concealing of conduit is not feasible), for light/fan/bell point complete all as specified and directed. (Note : Modular switch/bell push/fan regulator etc shall be measured and paid separately under respective items.)

All as per Srl item No. 100 above but one two way point controlled by two Nos switch 06 Amp two way, complete all as specified and directed.

All as per Srl item No. 100 above but for 5 pin 5 Amp socket outlet point on independent gang box and suitable support frame and cover plate (inner/outer) controlled by one switch 5Amp one way, etc complete all as specified and directed.

All as per Srl item No. 100 above but for 5 Pin 5 Amp socket outlet point on same board controlled by one switch 5 Amps one way on same gang box support frame and cover plate etc complete all as specified and directed.

All as per Srl item No. 100 above but for one 15Amp socket outlet point concealed using 2.5Sqmm FRLS PVC insulated multi-strand copper conductor wire including 2.5Sqmm FRLS PVC insulated unsheathed copper conductor earth wire and making good to disturbed surfaces of wall floor to match existing finishes complete all as specified and directed.

S&F Modular Socket outlet, 5 pin, multi purpose 2 module 6 Amps, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKSWW065 or equivalent of Legrand/Siemens/Schenider/Anchor Roma.

S&F Modular Socket outlet, 5 pin, multi purpose, 2 module 6/16 Amp, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKCWW163 or equivalent of Legrand/Siemens/Schenider/Anchor Roma

S&F Modular Switch 2 way 6/10 Amps , 1 module etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVSXXW101 or equivalent of Legrand/Siemens/Schenider/Anchor Roma.

S&F Modular bell push, 10 Amp, AC 230 Volt etc complete all as specified and directed. Make : Legrand Cat Part No 673404/ Anchor Roma Cat Par No 289101/ Schenider Cat Part No P1005.

S & F modular switch piano type flush button 16 Amp one module, complete all as specified and directed. Make : Legrand Cat Part No 673009/Crabtree Cat Part No ACMSXXW102/Anchor Roma Cat Part No 66104.

S & F modular switch piano type flush button one way 06/10 Amp one module complete all as specified and directed. Make : Legrand Cat Part No 673000/Crabtree Cat Part No ACMSXXW101/Anchor Roma Cat Part No 66111.

S&F Ceiling rose polycarbonate isolated body surface Bakelite, not less than 50x20mm, three terminals, AC 230 volts etc complete all as specified and directed. Make : Anchor (Penta) Cat Part No : 39040 or equivalent of Havells(Reo)/SSK (Topline)/GM (Vyoma)

S&F in repair for ceiling fan 1200mm sweep BEE certified 5 Star rated white including making connecting using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose and testing etc, complete all as specified and directed.

S & F Fan regulator modular step type suitable for 1200/1400mm sweep ceiling fan hum free, 120W- 2 module including necessary connections complete all as specified and directed. Make : Legrand Cat Part No 673028/Crabtree Cat Part No ACARFHW005/Anchor Roma Cat Part No 66502.

S&F for Bell Ding Dong AC 230 Volt, single Pole complete all as specified and directed. Make : Anchor Cat Part No 8024/Cona Cat Part No 2856/ Anchor Cat Part No 8272/GM Cat Part No 4001.

S&F Surface mounted 1x20 watt LED tube light fittings (4 feet long), prewired, decorative luminaire with inbuilt LED tube rod and acrylic end covers with all accessories and PVC Round/Square block for fixing of fittings and making connection with and including 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc complete all as specified and directed.

S &F in repair the Bulk head light fitting LED type 10 watt complete with 10 watt LED and having IP-63 protection and fixing on wall/ceiling complete with all accessories and including connecting up with ceiling rose with & including PVC insulated and overall sheathed flexible copper conductor cable and including 3 core 0.50 Sqmm complete all as specified and directed.

S&F Mirror decorative light of toughened glass and having with and including 1 X 11 Watt LED mounting on surface with high output diffuser and 1' length with all accessories connected with and including twisted flexible copper conductor all as specified and direted.

S &F building LED security light luminaries 45 W LED 5000K AC 230 volts, new generation saving & enviromental friendly long life versatile pressure die cast aluminium luminaries with high power LED as light source complete making connection with street light/ building security light box or OH line using PVC insulated and sheathed single core multi stranded copper conductor cable of size 1.5Sqmm including suitable size 32mm of bracket and light grade pipe for muntaining of fitting complete all as specified and directed.

S&F Lamp holder insulated body with back plate suitable for batten fitting including 12W LED lamp of approved make and cat part and PVC Round/Square block etc complete all as specifeid and directed.Notes : Notes for Srl item No 115 to 119:- 1. Driver shall be potted antivibration type. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be povided. 3. CRI (Colou Rendring Index) of fixture shall be > 70. 4. CCT (Colout Correlated Temprature of fixture shall be 5700K ± 300 K. 5. System Lumen Efficacy shall be > 100Lm/W 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 5 years gurantee shall be provided by contractor suppoted by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the Contractor shall replace / repair the defective fitting within 07 Days after handing over to Contractor for replacement / repair 11. CA No shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintaince required, if any can be carried out from Top cover.

S&F in replacement distribution board iron clad,double door with IP-43 protection suitable for MCCB as incomer and MCB as outgoing 415 Volts 3 phase 50 C/S '4' way, complete with and including approriate size copper busbar and neutral link complete with and including one MCCB 3 pole 415 Volts 100 Amps rating with rupturing cap 16 KA of the same make as of distribution board & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge. [Note :- Outgoing MCB only shall be measured and paid separetly]

S&F Double door MCB DB SPN, 240 Volts, 08 Way made out of CRCA powder coated sheets, IP43 protection with copper bus bar including taking out old unsv DB any size/type, complete all as specified and directed. Make: Legrand Cat Part No 6077-12 or equivalent model in L&T/Hager/SCHNEIDER

S&F for MCCB tripple pole & neutral (TPN) 415 volts, 100 Amps, 10KA complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB single pole (SP) 240 volts, 6 to 32 Amps, 10KA (C-series) , complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB single pole and neutral(SPN) 240 volts, 6 to 32 Amps, 10KA (C-series) complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F Single pole & neutral enclosure with a two pin & earth plug & socket complete with & including one single pole MCB 20 Amps 240 volts (C-series) complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F Heavy duty Exhaust fan, single phase, 220 Volts, 50 Hz, 1400RPM, 300mm sweep with louvers including cutting round opening, through one brick thick masonry wall suitable for exhaust fan by providing, fixing and removing shoring, forming jambs with CM 1:3 and making good disturbed surface to match existing finish and removal of rubbish out off the premises etc complete all as specified and directed. Make : Crompton Model No EXHD300-4-1 or equivalent model of Bajaj/Havells

Supply, installation, commissioning and testing of storage water Heater, 25 Ltr capacity 5 Star rated BEE certified, vertical type, ABS body, external thermostat, Single phase 220 volt, 50 Hz including Plug Top, inlet/outlet PVC connection ,15mm dia 450mm long braided in stainless steel wire with chrome finish for Hot & Cold water pipe line and necessary mounting arrangement by grouting split bolts of size 12mm dia and not less than 100mm long etc complete all as specified and directed. Make : Havells Model No Puro Plus/Bajaj Model No Calents/Crompton Model No Solarium DLX.

Supply, Installation as in repair including, Connecting & testing of tamper proof electronic AC, 240 Volts, 50Hz, Single phase, multi feature of rating 5 to 30 Amps static, energy meter (ISI marked) with backlit LCD digital display with special feature like TOD, Tamper logging, Optical communication port for down loading the data and push button for manual operation to read the data without opening box, two wire direct operated of accuracy class 1.0, operating voltage 140V to 300V, (measures & display KWH, V, I, KW, PF, last six months history of KWH & MD in KW) including factory fitted hinged meter box made out of polycarbonate engineering plastic transparent piller proof to house energy meter (conforming to IS-5133 Part-II) with protection class IP-51, dust, vermin & shock proof with 9 Pin D type male connector for cable used for interface between meter and CMRI including paint contract number on box and sealing the cover of box & taking out existing electric meter with or without box of any type etc complete all as specified and directed. Make : HPL Cat Part No SPPB1321120002ME03 or equivalent model in L&T/Hager/ Secure. Note : Old unserviceable electrical energy meter will be deposited in MES store yard to GE (South) Mamun.

Taking down ceiling/exhaust fan of any sweep & size and refix in same position after overhauling including minor repairs by replacement of capacitor, safety pin, cap, nuts & bolts etc and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose to fan, including testing to ensure efficient functioning including application of one coat of synthetic enamel paint by spray painting & rewriting number complete all as specified and directed.

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation etc (for cable, pole stay manhole etc), in any type of soil and getting out, complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25cm thick, etc complete all as specified and directed.

Removing excavation material n exc. 50m & deposited where directed at a level n exc. 1.5m above the starting point etc complete all as specified and directed.

M&L for Sub main wiring with FRLS PVC insulated unsheathed 2X6 sqmm multistranded copper conductor cable 1100 V with 1X6 sqmm FRLS PVC insulated green multistranded copper cable for continuous earth drawn through & including concealed PVC conduit of appropriate size not less than 20 mm dia & 1.8mm wall thickness with all accessories including cutting grooves and making good disturbed surface to match existing including taking down existing surface sub main wiring complete all as specified and directed. (Note: Two runs of FRLS PVC cable with one run of earth conductor and conduit shall be measured as one RM.) Make for wiring : Polycab/Anchor/Finolex

Supply , laying, testing and commissioning for 1100 volt grade XLPE insulated heavy duty cable, 25 sqmm 4 core, strip armoured with aluminium stranded conductor overall PVC sheathed laid in trenches including taking down existing cable & bricks complete all as specified and directed. Note : Excavation & Earthwork shall be measured and paid separately.

M & L for well burnt bricks , laid flat ( old size) sub class B designation 75 for cable protection complete all as specifed and directed.

M & L for sand filling in trenches dry and and clean sand unwashed including punning around cable for protection of under ground cable complete all as specified and directed. [Note : Punned thickness shall be measured and paid]

S&F for GI tubing 40 mm bore light grade laid in trenches/floors/ fixed to wall/poles for protection of cable with necessary fittings and FI clamps duly painted complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in the ground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground level connected to galvanized iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point, HDPE pipe 15mm bore as protection pipe, GI watering pipe 20mm bore light grade with funnel and wire mesh, charcoal and salt, 40mm thick pre-cast RCC (1:2:4) type B-0 (Nominal mix) cover reinforced with XPM (weighing n.less than 4 Kg/Sqm) with suitable steel handle, and angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-0 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing on completion, all as shown on electric plate No. 03 of SSR-2009 Part-I, complete all as directed. Notes: 1. Earth lead & protection pipes length upto & including 7.50 metre is deemed included in unit rate quoted by the contractor. 2. Earth filling shall be done by vegitable soil. 3. Soil shall be free from stone, boulders, aggregate, gravels .

GANDOTRA CONSTRUCTION CO

M/s. RAMESH KUMAR

Ravinder Singh

A V BUILDERS

M/S J N TRADERS

naresh kumar sharma

WALIA ENTERPRISES

M/S INDIAN ELECTRICAL

KULBHUSHAN AGGARWAL

abrol enterprises