REPAIRS TO SEEPAGE LEAKAGE OF ROOF CHAJJA WALLS AND CERTAIN MISC B R WORKS IN THE MD ACCN IN THE AOR OF AGE MEG AREA UNDER GE NORTH BANGALORE

Amount

Demolition of cement concrete and paving not exc 15 cm thick (below or above ground level) complete all as specified and as directed.

Demolition of brick work /stone masonry/pcc block masonry built in cement mortar of any description all as specified and directed.

Dismantling of floor, hearth or wall tilling incl cement mortar bedding (but not backing) and removing rubbish off from premises.

Taking down cement plaster of any description hacking for key or raking out joint on old brick work / stone / concrete surface

Taking up or down 15 mm existing steel tubing and connections all as specified and as directed.

Taking up or down 20 mm existing steel tubing and connections all as specified and as directed.

Taking up or down 25 mm existing steel tubing and connections all as specified and as directed.

S&F 20mm dia GI tubing medium grade and fixed complete to walls and ceiling or laid in floors complete all as specified and directed

S&F 25mm dia GI tubing medium grade and fixed complete to walls and ceiling or laid in floors complete all as specified and directed

Supply & laying 20 mm outer dia CPVC pipes SDR 11 ( Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings and specials complete all as specified.

Dismantling water tanks and removing to store (exc 250 and not exc 500 ltr capacity)

Dismantling water tanks and removing to store (exc500 and not exc 1000 ltr cap)

M & L rotational moulded polythene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I capacity of tank 500 ltrs complete all as specified and directed

Ditto all as per item No 1.013 above but except tanks

M&L rotational moulded polythene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I capacity of tank 1000 ltrs complete all as specified and directed

Ditto all as per item No 1.015 above but except tanks

S&F in repairs 20 mm dia of bore ball float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and as directed [Minimum weight for 20 mm – 210 gms] .

S&F in repairs 20 mm gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and including taking down old gate valve all as specified and as directed.

S&F in repairs 25 mm gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and including taking down old gate valve all as specified and as directed.

S&F in repairs Brass CP wall mixer for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed (Cat No-PIS-75H of Neptune series of Prayag or equivalent make as specified in CA)

S&F in repairs 15 mm Centre hole Basin mixture W/o Pop Up all as specified and as directed.(Cat No PIS-50 H Neptune series of Prayag or equivalent make as specified in CA)

S&F in repairs 15 mm pillar taps swan neck type, chromium plated cast copper alloy fancy type complete all as specified and as directed. (Cat No PIS-14H Neptune series of Prayag or equivalent make as specified in CA)

S&F in repairs 100mm (4") overhead shower ABS with brass Arm (225mm) & flange including fixing to steel pipe or union complete all as specified and as directed. (Cat No BS-73 Neptune series of Prayag or equivalent make as specified in CA)

S&F in repairs 15mm angle cock CP cast copper alloy screwed down high pressure with capstan head handle screwed both ends or for unions etc . (Cat No PIS-10H Neptune series of Prayag or equivalent make as specified in CA)

S&F Bib Cock 2 way double handle with CP flange as fixed in repair all as specified and as directed. (Cat No-PIS-12H Neptune series of Prayag or equivalent make as specified in CA)

S&F chromium plated long body bib tap 15mm dia with CP flange as fixed in repair all as specified and as directed. (Cat No-PIS-08H Neptune series of Prayag or equivalent make as specified in CA)

S&F chromium plated bib tap 15mm dia with CP flange as fixed in repair all as specified and as directed. (Cat No-PIS-06H Neptune series of Prayag or equivalent make as specified in CA)

S&F in repairs Health faucet, brass body with 1mtr SS braided tube & wall hook complete all as specified and as directed (Cat No-BEA-41/BEA-85 of Prayag or equivalent make as specified in CA)

S&F in repairs Towel rail stainless steel glossy finish complete all as specified and as directed. (Cat No-BA10S of prayag or equivalent make as specified in CA)

S&F in repairs Towel rack Brass glossy finish complete all as specified and directed (Cat No BA-03 of Prayag or equivalent make as specified in CA)

S&F in repairs Towel ring Brass glossy finish complete all as specified and directed (Cat No BA-02 of Prayag or equivalent make as specified in CA)

S&F in repairs Soap dish chromium plated brass all as per Cat Part No BA-45 of Prayag or equivlaent makes fixed in wall as per manufacturers instruction.

S&F in repairs Mirror 600x450 x 5-6mm thick with frame cat No BLM-01F of PRAYAG or equivalent make complete all as specified and directed

S&F in repairs PVC Mirror cabinet of size 400x500 mm (Cat No 554 of Prayag or equivalent make) complete all as specified and as directed.

S&F in repairs Unbreakable (Square) wall mounted shelf 500mm (Cat No BEA-47A of Prayag or equivalent make as specified in CA) complete all as specified and directed

S&F in repairs Unbreakable corner shelf (3Pcs set i.e 8"-1, 10"-1 & 12"-1) (Cat No BEA-44A of Prayag or equivalent make as specified in CA) complete all as specified and directed

S&F in repairs peg set of six (Cat No BEA 30 of Prayag or equivalent make of CA) fixed in wall as per manufacturers instruction

S&F in repairs Toilet paper holder (Cat No BA-88 of Prayag or equivalent make of CA) fixed in wall as per manufacturers instructions

S&F in repair PVC connection (Suitable for Cold Water Supply) 15 mm size with PTMT nuts of length 450 mm, all as specified and as directed.

S&F in repair PVC connection (Suitable for HOT Water Supply) 15 mm size with PTMT nuts of length 450 mm, all as specified and as directed.

M&L 32 mm dia waste fittings,brass,chromium plated for sinks,basins,etc with long screwed shanks and flynuts,flange end fixed in repair complete all as specified and as directed

S&F in repair 75mm dia PVC(SWR) Multi floor trap,plain with grating including jointing with slvent cement all as specified and as directed.

S&F in repair grating doom 100 mm dia of PTMT complete all as specified and as directed

S&F kitchen sink with drainage board made of stainless steel 1mm thick kitchen or laborotry with plugs, washers and wastes including bedding in mortar on to dwarf wall or including fixing cantilever brackets and connecting union pipes overall size 915x460mm bowl size 410x330x160mm complete in repairs including Dismantling of old sink .

S&F of kitchen sink made of stainless steel 1mm thick kitchen with plugs, washers and wastes: including bedding in cement mortar to dwarf wall or including fixing cantilever brackets or fixing in granite slab and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete in repairs including Dismantling of old sink

S&F in repairs stainless steel plate rack of 0.63mm thick sheet, size 800mm x 600mm complete all as specified and as directed

S&F vitreous china wash basin white flat back size550x400mm excl chain and plug and porcelain stopper but incl CI bracket. waste fittings, brass chromium plated for glazed ware sinks, basins etc with long screwed shanks and flynuts, flange end bedded in red leead cement and other end fixed, PVC waste pipe 75 cm long complete all as specified and directed fixed in repairs

S&F vitreous china wash down water closet pan (Pedestal Pan) including fixing bolts, flush pipe anti syphonage pipe, plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device etc complete of cera model cat pt no. 2008 incl plastic EWC seat cover, coloured closed pattern with flat bottom and cover of cera model cat pt 2308 and mild steel chromium plated or aluminised hinging device as in repairs complete all as specified and directed

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including PVC SWR P trap connecting to flush pipe and to anti syphonage pipe, etc. complete including making good to floor, fixed in repairs complete all as specified and directed.

PVC valveless, syphonic action type, flushing cistern, Duo Flush cistern 10ltr capacity,low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes and fixing of chain and pull, or lever, fixed in repairs complete all as specified and directed. (Cat No-502 of Prayag or equivalent in any approved make as in CA)

M & L cement concrete type B0 1:2:4 (12.5 mm graded agg) 25mm thick finished even and fair.

M&L Screed bed or bedding layer of mortar 15mm thick in CM 1:6 for laying floor finishes complete all as specified and directed

M&L Rendering 10mm thick in CM (1:3) on Brick work or stone masonry surface as backing coat of tiles complete all as specified and directed

M&L Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

M & L Glazed coloured ceramic tiles in vertical surfaces 300x450x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed

M&L for vitrified ceramic light coloured tiles 8-10mm thick (square/rectangular)polished, area of each tiles not exc 0.36sqm in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

M&L for vitrified ceramic light coloured tiles 8-10mm thick (square/rectangular)polished, area of each tiles not exc 0.36sqm in vertical surfaces such as skirtind/dados, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

M&L Pre-polished Machine cut Granite stone slab 25mm thick with edge rounded one side laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Taking down chowkat (without taking of shutter from the frame) not exc 1.5 sqm each including making good the disturbed surface in PCC 1:2:4 type B0 or CM 1:3 all as specified and directed

All as per Item No 1.059 above, but exc 1.50 sqm and not exc 4.00 sqm each

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each all as specified and as directed

S&F in repairs 18mm thick, PVC sheet one side prelaminated of approved texture ("Celuca Ply of Rajshree make or equivalent as approved by GE) as in Kitchen cabinet (with shelves and partitions) including necessary fittingS&Fixtures as per manufacturer's instructions complete all as specified and directed.

S&F stainless steel kitchen basket in various type of basket , plain basket height 4" Thali basket 8" height Cup saucer 4" heigt and perforated cutlury basket 4" height all as specified and directed.

S&F Stainless steel channel for basket sizes 600mm long and 46mm wide all as specified and directed (Make : Hettich/Godrej)

S&F stainless steel handle for basket size 6" all as specified and directed

S&F stainless steel Auto closing concealed hinges 9.5 cranks for half overlay doors with opening angle 95* (14-32mm) with integrated overlay adjustment +_ 2.50mm & depth adjustment 4mm complete all as specified. Make : Godrej / Hettich.

S&F in repairs 18/19MM THICK Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, alround 6mm thick teak wood fillets fixed in kitchen Cabinet or cupboards all as specified.

M&L for Plain fillets square, rectangular or triangular in section clean sawn , secured with nails or brads of second class hard wood fixed to cupboard shutter Not Exc 3 sqcm cross section area all as specified and directed.

Solid PVC door frame (Single rebated) of size 60 mm x 30 mm made out of solid foam with homogenious fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100x8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) complete all as specified and directed

M & L for factory made solid PVC moulded door shutter , 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm plain colour PVC sheet on back face supplying and fixing in frame at site as per specification & drawing with wood free EPS .

S&F Flush door shutters 35mm thick, factory made as per IS:2202 (Part-I 1999) solid core construction, with block board core with decorative face veneer both faces with lipping/frame to match as per drawing fixed to chowkhats all as speified and directed

S&F 2nd class hard wood plain, solid, straight chowkats and frames, clean sawn, frame rebeated on the solid , rounded or chamfered, put tegether with glue pinned at joints etc complete all as specified and as directed

S&F 2nd class hard wood 35 mm thick made glazed and skeleton shutters open rebated and prepared to receive glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) kiln seasoned and chemically pressure treated complete all as specified and as directed

S&F framed work as in doors or gates of angle or other sections with gusset plates, rails braces, etc complete drilled for fixing of steel sheeting or other covering, doors etc, to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings(exclusive of steel sheeting or other covering, running rails and guides) and hanging ; also fastening and fixing complete including painted with one shop coat of zinc chromate primer paint (including preparation of surface) at contractors workshop/factory before fabrication complete all as specied and directed

M&L preparing new wooden surface of any description, not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and as directed

M & L applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces over 10 cm width or girth including preparation of new steel surfaces

S&F Butt hinges stainless steel 100mm long and fixed to door frame and shutter duly welded / screwed complete all as specified and as directed

S&F Butt hinges medium weight, cold rolled mild steel 100mm long and fixed to door frame and shutter duly welded/screwed complete all as specified and as directed

S&F Aluminium anodised tower bolt 150mm long of extruded section etc complete all as specified and as directed

S&F Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed

S&F 150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed

S&F aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as specified and as directed

S&F 150 mm floor door stopper of aluminium alloy powder coated, with hard down steel spring all as specified and as directed.

S&F in repair mild steel 300mm, ordinary rat tail rod pattern springs,including roller and roller plate complete

S&F Anodised aluminum powder coated (of any shade/colour as approved by GE ) ventilators with adjustable 4mm thick figured glass louvers, fixed in qtr portion, without sash bars, aluminum section weighing 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws, including stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.18mm including complete etc all as specified and directed by the Engineer-in-charge (Size of Ventilators = 600 x 900 mm)

S&F Anodised Aluminum Powder coated three track sliding aluminum window including Frame and shutters consisitng of 2xglazed shutter (thickness of glass not less than 5mm) & 1xGauged shutter(stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature 1.40mm), Aluminum sections weighing n.less than 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws, anodised aluminum fittings such as peg stays, self closing clips, handles etc all as specified and directed

S&F Box type Steel Windows/Ventilators double side shutters (Windows side hung type, Ventilators top hung) pressed steel frames made out CRC Sheet of 80x60x1.25mm double rebated, Shutters box type made out of CRC Sheet of 40x20x1.0mm, windows & ventilator shutter fixed made of glass and gauge fixed with box type hinges, Aluminium die cast handles for glass shutters, Iron flat type handles for mesh shutters, Telescopic stays, etc complete all as specified incl 12mm square guard bars/grill welded with steel frame (100c/c horizontically) all as specified and directed by Engineer-in-Charge. NOTE: (i) Payment under this item will be make combined for steel frames, steel shutters and Guard bard / Grill, However unit rate quoted shall deemed to include cost of beading, fittings such as handles, hinges, Telescopic stays, locking arrangements and fixing of glass and wiremesh etc. (ii) Supply only 4 mm thick sheet glass and stainless steel wire mesh be measured and paid separately. (iii) Weight of Grill/Guard Bars, handle,hinges and locking arrangements shall not be accounted for payment purpose . (Note : All Windows/Vent design as per CECZ TD drg No 539)

Hacking out old broken glass (any thickness, size, quality or description) from wooden surface concrete or brick surrounds. Glazed with putty or fixed with beads all as specified.

S&F Sheet glass 4mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane and all as specified.

S&F stainless steel wire cloth 0.36mm nominal dia and average width of aperture 1.40mm and fixed with tinned tack or galvanized wire staple all as directed fixed.

S&F grid suspended false ceing grid system of size 600x600mm with main runner 29x24.7x0.8mm cross tee 29x24.7x0.8mm and wall angle 22.2x22.2x0.65mm. Ceiling suspended with 3mm dia GI wire hanger fixed with steel dash fastner, butter fly clips, hold down clips etc (Main runner, cross tee& wall angle of MS galvanised with PPPCGS) including 4mm thick HPSC self textured design pre primered non asbestos fibre cement building board fixed to false ceiling complete including taking down old celing of any description .

M&L Precast cement concrete block masonry Type C1 1:3:6 (using 20mm graded stone aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L providing cement concrete type B0 1:2:4 (12.5mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges in chajjas etc complete all as specified and directed.

M&L for rendering 15 mm thick on fairfaces of brick work or concrete surfaces in cement mortar 1:6 finished plastered surface even and smooth without using extra cement

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:4 with WPC, finished plastered surface even and smooth without using extra cement Note :- WPC will be measured and paid separately

Supply only liquid water proofing compound

M&L for rendering 5 mm thick on ceiling /RCC surfaces in cement mortar 1:3, finished plastered surface even and smooth without using extra cement

M&L Cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) 100mm thick as in subbase

M&L for cement concrete type C-1, 1:3:6 ( using 20 mm graded crushed stone aggregate ) 75mm thick as in plinth protection, laid in alternate bays (not exceeding 2 Sqm each) finished the concrete surface even and smooth at top without using extra cement and providing joints throughout the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight all as specified and directed

M&L chequerred cement concrete tiles 300x300x25mm thick set and jointed and pointed in neat cement slurry with grey cement and pigments to match the colour of tiles over and including 20mm thick screed bed in CM (1:4) complete all as specified and directed by Engineer-in-Charge

Supply and spreading of M-sand as cushioning material complete all as specified and directed

M&L Machine pressed (rubber mould) precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, of M-35 grade with grey cement and pigment complete all as specified and directed.

M&L Preparation of newly plastered surfaces and applying two coat of oil bound distemper over a coat of alkali resistent primer over two coats of wall care putty complete all as specified and directed

M & L preparation of newly plastered surface of wall and applying two coats of cement base paint complete all as specified and as directed.

M & L for preparing newly plastered ceiling surfaces and applying three coat of white wash complete all as specified & as directed.

M&L for providing and laying water proofing treatment to sunken portion of WCs, bathroom and kitchen etc by applying cement slurry mixed with two component Elastomeric Acrylic based polymer modified cementitious composite compound coating of make as approved in TI 5/2003 including demolition and removal the same from site of existing treatment of any type. The following procedures to be adopted during the execution of work :- (i) Demolition of existing treatment of any type including cleaning and removal of debris from site. (ii) First layer of slurry of cement @ 0.488 kg/sqm mixed with Acrylic based polymer modified cementitious composite compound @ 0.253 kg/sqm. The layer will be allowed to air cure for 4 hours. (iii) Second layer of slurry of cement @ 0.242 kg/sqm mixed with with Acrylic based polymer modified cementitious composite compound @ 0.126 kg/sqm. The layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (iv) 20mm thick screed in cement mortar 1:3 mixed with liquid water proofing compound as per manufacturers instructions above the treated area. Contd/--1.107

Contd/-1.106 (v) Ponding the treated portion atleast 48 hours. if any leakage/seepage observed the entire procedures will be repeated without any extra cost. (vi) Provide 40mm dia light grade GI spout at the lowest point with 30cm projection beyond the out face of the wall. (vii) Sunken portion shall be filled with lean concrete 1:5:10 type E-2(using 40mm graded stone aggregate). Note :- (i) The sunken slab sloped towards outer face so as the drain the water to GI Spout pipe. (ii) Coving shall be provided at the junction of slab with the wall. (iii) Nahni trap shall be 10mm below finished floor level. Ensure the drain of pipe dia is larger than the nahni trap size. (iv) The outer end of the spout should be chamfered.

Demolition of existing roof treatment of any type including cement plaster 15 mm thick and providing screed bed/rendering 10mm thick in CM (1:3) mixed with and including supply of approved water proofing compound as per manufacturers instructions by removing all loose gravel, dirt, oil, grease and foreign materials by jet or dry air, cleaning the surfaces mechanically or by grinding to make it smooth and applying APP modified water proofing membrane as per IS 1654-2017/IS 16352-2017 , 3mm thick and weighing not less than 3.60kg/Sqm reinforced with non woven polyster/HMHDPE matt black finished over compatible primer/bonding bitumen @ 0.40 Litr/Sqm and torch applications of membrane with 75mm side overlap and 100mm end lap after necessary preparation of surface complete as per manufacturer's instructions and applying a coat of solar reflective bituminous aluminum paint on top @ 0.10 litre/sqm complete all as specified and directed.

M&L providing cement concrete type B0 1:2:4 (12.50mm graded stone aggregate) in copings, parapets and railing upto 60cm height, leveling concrete for Roof slab, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed

Disconnecting to existing PVC tanks, setting aside ( for lowering down if required) for repairs, if hoisting if required reconnecting and refixing in position cap upto 1000 ltr including cleaning of overhead tank including removing the sludge washing down with detergent powder & writing the date of cleaning with paint complete all as specified and as directed

Material and labour for spraying antiweed / non toxic solution / chemicals containing Glyphosate as per manufacture instructions and removing the weed including the roots after ensuring complete de-germification of palnt/weed and cutting down the plant/trees off from roof/top sides of external walls of bldgs, in chajjas, wall junctions, junctions of GI/CI/AC/PVC pipes and taking out roots entered in wall/slabs, including making good the surface using PCC 1:2:4 type B1 or cement mortar (1:2) or brick work in CM(1:4) plastered with CM(1:4) to match with existing surface and repairing the pipes and joints which was affected by cutting down/taking out process all as specified and as directed for plants / trees located in the buildings upto four storey high, complete all as specified and directed by Engineer-in-charge. NOTE:- Contractor has to execute the work of de-generated plant/weeds as per the prior approval and directions of Engineer-in-charge.

All As per item no 110 here in before but plants located in the buildings of five to eight storey high.

Material and labour for cleaning of Roof height of (on accessible roof height N.exc 30RM /inaccessible roofs height N.exc 10RM) by removing all scale, dirt, mud, any foreign material, accumulated silt, other dirty substance, algae, fungus , leaves etc deposited over slab and making good the distrubed surfaces if any with and including making good the surface using PCC 1:2:4 type B1 or cement mortar (1:2) or brick work in CM(1:4) plastered with CM(1:4) to match with existing surface and removing the material so obtained out side complete all as specified and directed by Engineer-in-charge. NOTE:- Contractor has to submit the phtographic record of work done (before and after the work done duly annoted the Building No/Location) at the time of claiming the payment (RAR/Final Bill). No payment has to be made without submit the photographic records. (a) Area of Roof upto 500sqm

(b) Area of Roof exc 500Sqm

S&F in repair 75 mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including necessary fittings all as specified and as directed.

Ditto all as per item No 1.115 above but 110 mm dia .

S&F in repair 75mm dia PVC (SWR) Bends with access door of any radious

Ditto all as per item No 1.117 above but 110mm dia

S&F in repair 75mm dia PVC (SWR) junction single(single T) equal or unequal with access door

Ditto all as per item No 1.119 above but 110mm dia

S&F in repair 110mm dia PVC(SWR) brach piece, single(single Y) equal or un equal with access door

Ditto all as per item No 1.121 above but 75mm dia

S&F in repair 110mm dia PVC(SWR) brach piece,(double Y) equal or un equal with access door

Ditto all as per item No 1.123 above but 75mm dia

S&F in repair 75mm dia PVC(SWR) vent cowl

Ditto all as per item No 1.125 above but 110mm dia

B5BUILDING SOLUTIONS

S S BUILDERS

Shanmuga Constructions

RK Builders

Sreyas Enterprises

J PUSHPALATHA ENGINEER AND CONTRACTOR

SHRI NARAYANADRI ENGINEERS & BUILDERS

PRACHANIVA CONSTRUCTIONS

Sangam Construction