Construction of 6 No. Type-II Quarter for PWD Staff at Chamba Construction of Building portion including W.S.and S.I. and Rain Water Harvesting System

Amount

Excavation in foundation and trenches in all heights and depths and in all kinds of soil including saturated soils comprising of pick work, jumper work, pick jumper work, blasting work both in soft and hard rock, chiseling / wedging out of rock (Where blasting is prohibited) and their intermediate classification of soil setting out true to the required lines, grade, width, cutting and trimming of side slopes as shown in the drawing and if water is met within the excavation due to springs, seepage, rain and other causes it shall be removed by the suitable diversion pumping or bailing out and excavation shall be kept dry wherever so required by the contractor at his own cost as directed by the Engineer-in-charge and disposal of all surplus excavated soil in acquired width or at an approved dumping side including its stacking leveling dressing including all leads and lifts by head-load, mechanical transportation or by any other mode of transportation with all cost of labours, machineries and other incidentals to complete the work as per HPPWD specification. Any loss to the public and private property during the course of execution and disposal of unserviceable material shall be absolute responsibility of the contractor which shall have to be compensated by him in all cases.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including all taxes, carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in foundation, footing, basis of columns etcetra and mass concrete including all taxes, carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Columns, pillars, posts and struts square rectangular or polygonal in plan including all taxes, carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Beams, cantilever, girders and lintels. Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto all depth and in all heights from floor including all taxes, carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings and the like floor etcetra upto any thickness including all taxes, carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Stair cases with sloping or stepped soffits excluding landing including all taxes, carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.

Providing and laying mechanically mixed and vibrated cement concrete work of grade M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 330 Kg/Per cubic metre ( Three hundred thirty kilograme per cubic metre) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in foundations, footings bases of columns and the like and mass concrete including all taxes, carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.

Providing and laying mechanically mixed & vibrated cement concrete work of grade M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 320 Kg/Per cubic metre ( Three hundred twenty kilograme per cubic metre) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in columns, pillars, posts and struts upto floor all levels as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and laying mechanically mixed & vibrated cement concrete work of grade M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 320 Kg/Per cubic metre ( Three hundred twenty kilograme per cubic metre) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in suspended floors, roofs, landing, shelves and their support, balconies, beams, girders, bressumers and cantilever upto floor all levels as per the directions of the Engineer-in-charge including all taxes. carriage of material within all leads and lifts and other incidentals.

Providing and laying mechanically mixed & vibrated cement concrete work of grade M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 320 Kg/Per cubic metre ( Three hundred twenty kilograme per cubic metre) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in stair cases and connected work upto floor all levels as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and laying mechanically mixed and vibrated reinforced cement concrete work of grade M-20 (M-twenty) design mix to obtain the minimum compressive strength of 20 N/mm square (twenty newton per square millimetre) with cement contents not less than 320 Kg. (Three hundred twenty kilogramme) / Cubic metre and curing complete including form work chajjas upto any thickness and upto floor all level including finishing the exposed surfaces with cement mortor 1:3 ( One cement isto three sand) to give a smooth and even surface centering /form work and curing complet excluding the cost of reinforcement as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and laying mechanically mixed and vibrated plain cement concrete 1:4:8 (one cement isto four sand isto eight graded crushed stone agreegate 40 mm (forty millimetre) nominal size) and curing complete excluding the cost of form work in foudation and plinth including all taxes, carriage of material, within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing and laying mechanically mixed and vibrated cement concrete 1:6:12 (one cement isto six sand isto twelve graded crushed stone aggregate 40 mm (forty millimetre) nominal size) and curing complete excluding cost of centring and shuttering in foundation and plinth including all taxes, carriage of material, within all leads and lifts within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing tor steel reinforcement for reinforced cement concrete work including straightening, bending, binding and placing in position complete as per the directions of the Engineer-in-charge including all taxes, carriage of material, carriage of material within all leads and lifts and other incidentals.

Providing and laying precast cement concrete hollow block masonry with cement concrete blocks of size 30cm x 15cm x15 cm (Thirty into fifteen into fifteen centimetre) including quion block jamb blocks and closers etc. made of cement concrete 1:3:6 (one cement isto three sand isto six graded stone aggregate 20mm (twenty millimetre) nominal size) laid with cement mortar 1:6 (one cement isto six sand) including curing complete in super structure within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Half brick masonry using second class common brunt building brick of approved quality in super structure above plinth level upto floor all levels in cement mortar 1:4 (one cement isto four sand) curing complete including all taxes and carriage of material, as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

Random rubble masonry/polygonal rubble masonry (uncoursed / brought to courses ) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement isto six sand isto twelve graded stone agreegate 20mm (twenty millimetre) nominal size) at plinth level in cement mortar 1:6 (one cement isto six sand) as per the directions of the Engineer-in-charge including all taxes and carriage of material within all leads and lifts and other incidentals.

Stone filling under floor/ behind retaining wall curing complete including all taxes and carriage of material, within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing and fixing 40 mm (forty millimnetre) thick second class deodar wood panelled, glazed or panelled and glazed shutters for doors, windows, clerestory windows including black enamelled iron butt hinges with necessary screws within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing and fixing 40 mm (forty millimetre) thick second class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G(eighty five G) with wire of dia 0.56 mm (zero point five six millimetre) for doors, windows and clerestory windows including bright finished black enamelled iron hinges with necessary screws within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing and fixing 25mm (twenty five millimetre) thick commercial board water prooof shutters for cup boards i/c fixing with nickel plated piano hinges with screws etcetera complete within all leads, lifts as per the direction of the Engineer-in-charge and other incidentals.

Providing and fixing factory made panelled or with PGI sheet linning upto 1.00 mtr. )one metre) inner side including bright finished black enamelled iron hinges with necessary screws complete within all leads, lifts as per the direction of the Engineer-in-charge and other incidentals.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etcetra complete 250 X 16 mm (two hundred fifty into sixteen millimetre) within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.

Providing and fixing aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetera complete 200 X 10 mm (two hundred into ten millimetre) within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.

Providing and fixing aluminium handles anodized transparent or dyed to required colour and shade with necessary screws etcetera complete 125 mm (one hundred twenty five millimetre) within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.

Providing and fixing bright finished or / and black enamelled iron Helical door spring 150mm (one hundred fifty millimetre) within all leads and lifts as per the direction of Engineer-in-charge and other incidentals.

Providing and fixing M.S. plain grills of required pattern in wooden frames of windows etc.with M.S.Flats, square or round bars with round headed bolts and nuts or by screws within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing and laying vibro hydraulic compressed and polished precast terrazo tiles 20mm (twenty millimetre) thick of 300mm X 300mm (three hundred millimetre into thre hundred millimetre) size ISI mark No. 1S-1237 with 70% (seventy percent) white and 30% (thirty percent) grey cement with marble chips ratio of 55% (fifty five percent) white and 15% (fifteen percent) each of green, yellow and maroon shade of specified sizes laid in floors, treads of steps and landings on a bed of 25mm (twenty five millimetre) average thicknes of cement mortar 1:6 (one cement isto six sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (where ever required) including rubbing and polishing complete within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing and laying vibro hydraulic compressed and polished precast terrazo tiles 20mm (twenty millimetre) thick (with marble chips of specified sizes) fixed on wall on 10mm thick cement plaster 1:3 (0ne cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles including rubbing and polshing complete mark No. IS-1237 with 70% (seventy percent) white and 30% (thirty percent) grey cement with marble chips ratio of 55% (fifty five percent) white and 15% (fifteen percent) each of green, yellow and maroon shade of specified sizes within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing and laying 20mm (twenty millimetre) thick white makrana marble work (table rubbed and polished ) in flooring on 20mm (twenty millimetre) thick cement mortar 1:3 (one cement is to three sand) including jointing with cement mortar (one cement isto two marble dust) with an admixture of pigment to match the shade of the marble including carriage of material within all leads and lifts as per and as per the direction of the engineer-in-charge and other incidentals.

White glazed tiles 6mm (six millimetre) thick in skiriting or risers of steps and dado on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) finished with flush pointing in white cement as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

Steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a primming coat of red lead paint in trusses and trusses purlins in building including all taxes, carriage of material within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.

Providing and fixing moulded hand rail of M.S. hollow pipe 50mm (fifty millimetre) dia welded in straight length over M.S. flat at top of vertical balusters including one coat of red oxide priming coat complete (M.S. flat & balusters of railings shall be measured & paid separately) including carriage of material within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.

Providing and fixing steel door, windows, ventilaters and clerestory windows frame manufactured from M.S. channal 75x40mm (Seventy five into forty millimetre), size vertically welded with M.S. flat 75 X 4mm (Seventy five into four millimetre) for central frames with split to end tail to each jambs including joints and miterd and welded with 16 X 3.15mm (Sixteen into three point five millimetre) lugs 10cm (ten centimetre) long embedded in cement concrete block 15cm X 10cm X 10cm (Fifteen centimetre into ten centimetre into ten centimetre) size of 1:3:6 (one cement isto three sand isto six graded crushed stone aggregate twenty millimetre nominal size) with provision for locking arragnement and shock observor fixed with by mechanical means lugs and curing complete including applying a coat of approved steel primer after pretreatment of the surface as specified within all leads and lifts as per the direction of Engineer-in-Charge and other incidentals.

Providing and fixing 0.60mm (zero point six zero millimetre) thick prepainted steel sheets roofing made of cold rolled steel roll with spray coating of 25 micron with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 micron (twenty micron) over 5 microns (five micron) primer coating and back coat of polyster of 5 microns (five micron) over 5 microns (five micron) primer coating of TATA / SAIL/ RELIANCE/ ZINDAL STEEL including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia metre with prepainted limpet washers complete with all accesories as required including all taxes, carriage of material within all leads and lifts and as per specification or as per the direction of the engineer-in-chief and other incidentals.

Providing and fixing ridges or hips 60cm (sixty centimetre) overall 0.60mm (zero point six zero millimetre) thick prepainted steel sheets in roofing having proper gola shape with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 micron (twenty micron) over 5 microns (five microns) primer coating and back coat of polyster of 5 microns (five microns) over 5 microns (five microns) primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia metre with prepainted limpet washers complete with all accesories as required including all taxes, carriage of material within all leads and lifts and as per specification or as per the direction of the engineer-in-chief and other incidentals.

Providing and fixing valley 90 cm. (ninety centimetre) overall with 0.60mm (zero decimal six millimetre) thick prepainted steel sheets in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 micron over 5 micron primer coating and back coat of poltster of 5 micron over 5 micron primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia and prepainted G.I. limpet and bitumen washers complete with all accessories including all taxes, carriage of material within all leads and lifts and as per specification or as per the direction of the engineer-in-chief and other incidentals.

Providing and fixing M.S. B.P. sheet 1.66mm (one point six six millimetre) any thickness in eaves board / facia / soffits / ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per specification including all taxes, carriage of material within all leads and lifts and as per the direction of the engineer-in-chief and other incidentals.

Providing and fixing 15cm (fifteen centimetre) wide 45cm (forty five centimetre) overall semicircular plain 0.63mm (zero point six three millimetre) thick G.I. sheet gutter with iron brackets 40x3mm (forty into three millimetre) size bolts and nuts and washers etcetera including making necessary conections with rain water pipe complete as per design including all taxes, carriage of material within all leads and lifts and as per specification or as per the direction of the engineer-in-chief and other incidentals.

Providing and fixing angle iron door, window, clerestory window frame manufactured from steel iron section of 40x40x6mm (forty millimetre into forty millimetre into six millimetre) thickness including hinges jamb, lock jamb, beed and if required angle thrashold of mild steel angles 50x25mm (fifty millimetre into twenty five millimetre) welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including steel but thinges 2.5mm (two point five millimetre) thick with provision for locking arrangement and shock as specified and applying a coat of approved steel primer after preteatment of the surface as dirceted by Engineer-in-charge within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing and fixing double rebate steel windows side hung one glazed and other wire gauge of standard rolled steel sections joints mitred and welded with mechanical means to relevent ISI standard specification frames and in M.S. Tee section 25X15X3mm (twenty five millimetre into fifteen millimetre into three millimetre) including glazing clips or pins, glass panes, M.S. wire mesh 4 designation 85 (eighty five) SWG and M.S. fitting as required including providing and fixing of projecting, hinges, tower bolts, handles, hooks and eyes, presty, locking arrangment spring catch etcetra and providing and fixing wire mesh fly proof including fixing with special metal sesh putty of approved make complete including applying a priming coat of red lead paint within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Supplying and fixing 4mm (four millimetre) thick plain glass panes in fixed glazing with rubber gasket and aluminium channel beed including standard roll sections frame work within all leads and lifts as per the direction of Engineer-in-Charge and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter with Readymixed paint brushing wood primer pink as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

Painting two coats (excluding priming coat ) on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of dirt, dust and other foreign matter, sand papering and stoping with enamel paint other than white as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

Painting two coat (excluding priming coat) on new steel and other metal surfaces under coat with ready mixed paint brushing to give an even shade including cleaning the surface all dirt, dust and other foreign matter With white readymixed paint within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

6mm (six millimetre) thick cement plaster to ceiling in cement mortar 1:3 ( one cement isto six sand) as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

20mm (twenty millimetre) cement plaster in single coat on rough side of brick / concrete / stone masonry for interior plastering upto floor all levels including arises, internal rounded angle, chamfer and / or rounded angle not exceeding 80mm (eighty millimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement isto six sand) as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

15mm (fifteen millimetre) thick cement plaster in single coat on fair side of brick / concrete / stone walls for interior plastering upto floor all levels including arises, internal rounded angles, chamfers and / or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth with cement mortar 1:6 (one cement isto six sand)as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

Distempering two coats with oil bound washable distemper of Asian / Nerolac approved brand and manufacture and of required shade on un-decorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and including preparing the surface even and sand papered smooth as per the directions of the Engineer-in-charge including all taxes carriage of material within all leads and lifts and other incidentals.

Finishing walls with weather proof exterior grade emulsion of approved design (Apexultima) or its equivalent on undecorated wall surface (two coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matter etc. including sand paper smooth complete as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

Applying Birla white wall care putty over plastered surface after thoroughly brushing the surface free from mortar drops, dust loose materials and other foreign matter sand papered smooth to give final matter finish to the surface complete as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

Providing under layer for plinth protection of 75 mm (seventy five millimetre) thick (unconsolidated) bed of dry brick / stone agreegate 40 mm (forty millimetre) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing plinth protection 50 mm (fifty millimetre) thick in cement concrete 1:3:6 (one cement isto three sand isto six graded stone agreegate 20 mm(twenty millimetre) nominal size) within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Constructing course rubble hammer dressed 'U' shape open surface drain with side wall 15 X 23 cm (fifteen into twenty three centimetre) in cement mortar 1:6 (one cement isto six sand) and inside plastering with cement mortar 1:3 (one cement isto three sand) including earth work and laying 10 cm (ten centimetre) cement concrete in 1:5:10 (one cement isto five sand isto ten graded stone agreegate 40 mm (foty millimetre) nominal size) and 7.5 cm (seven point five centimetre) cement concrete 1:2:4 (one cement isto two sand isto four graded stone agreegate 20 mm (twenty millimetre) nominal size) and finished with a floating coat of neat cement complete as per standard design within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing and fixing on wall faces PVC (D-plast) 100mm dia (one hundred millimetre diametre) rain water pipes working pressure not less than 4.5 Kg (four point five) kilogram per square metre including filling the joints with approved adhesive complete within all leads and lifts and as per the direction of the Engineer-in-Charge and other incidentals.

Providing and fixing on wall faces PVC (D-plast) 100mm (one hundred millimetre) dia PVC plain bend for rain water pipes including filling the joints with approved adhesive complete within all leads and lifts and as per the direction of the Engineer-in-Charge and other incidentals.

Providing and fixing to wall, ceiling and floor galvanised mild steel tubes (medium grade) tube fittings and clamps including making good the wall, ceiling and floor 15 mm (fifteen millimetre) nominal bore including carriage of material within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals

Providing and laying in trenches galvanised mild steel tubes (medium grade) tube fittings (Earth work in trenches to be measured and paid for separately) 15 mm (fifteen millimetre) nominal bore including all taxes, carriage of material within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals

Making connection of galvanised steel distribution branch with galvanised mild steel main 20 mm to 40 mm (twenty millimetre to forty millimetre) nominal bore by providing and fixing tee including cutting and threading the pipes complete including all taxes, carriage of material within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.

Providing and placing in position 1000 (one thousand) litres net capacity PVC water storage tank of ISI 12701 marked G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangment including hoisting upto all heights above ground level.as per the directions of the Engineer-in-charge including all taxes carriage of material within all leads and lifts and other incidentals.

Providing and placing in position 500 (Five hundred ) litres net capacity PVC water storage tank of ISI 12701 marked G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangment including hoisting upto all heights above ground level.as per the directions of the Engineer-in-charge including all taxes carriage of material within all leads and lifts and other incidentals.

Providing and fixing high pressure PVC spigot and socket of supreme make , waste and ventilating pipes ISI marked including fixing with approved adhesive 150 mm (one hundred fifty millimetre) dia as per the directions of the Engineer-in-charge including all taxes carriage of material within all leads and lifts and other incidentals.

Providing and fixing high pressure PVC spigot and socket of supreme make , waste and ventilating pipes ISI marked including fixing with approved adhesive 110 mm (one hundred ten millimetre) dia as per the directions of the Engineer-in-charge including all taxes carriage of material within all leads and lifts and other incidentals.

Providing and fixing PVC 110x90mm (one hundred ten into ninety millimetre) dia floor trap ISI Marked of self cleaning design including fixing with approved adhsive, cost of cutting making the walls and floors etc. complete including all taxes, carriage of material within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive 150 mm (one hundred fifty millimetre) dia as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive 110 mm (one hundred ten millimetre) dia as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and laying PVC plain bend of ISI marked including fixing with approved adhesive etc. complete 150 mm (one hundred fifty millimetre) dia as per the directions of the Engineer-in-charge includingall taxes, carriage of material within all leads and lifts and other incidentals.

Providing and laying PVC plain bend of ISI marked including fixing with approved adhesive etc. complete 110 mm (one hundred ten millimetre) dia as per the directions of the Engineer-in-charge includingall taxes, carriage of material within all leads and lifts and other incidentals.

Providing and fixing vitreous China water closet squatting pan (Indian type W.C. pan) ( earth work, bed concrete, foot rest and trap to be measured and paid for separately). Orrisa pattern No. 2004 of size 58x40 cm. of hindware / Cera in white shade as per specification or as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and fixing PVC P or S trap for water closet (squatting pan ) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete 150mm (one hundred fifty millimetre) dia as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and fixing PTMT coloured/ white high density polythene / poly prolylene 10 litre (ten litre) capacity low level P.V.C. cistern plus) flushing cistern with a pair of C.I. or M.S. brackets complete with fitting such as lead valve syphon, 15mm (fifteen millimetre) dia PVC wall valve , coupling for connection with inlet, outlet and overflow pipes 40mm (forty millimetre) dia C.P. flush bend including cutting holes and making good the same (overflow pipe to be measured and paid for separately) as per specification as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and fixing vitreous China wash basin of Hindware with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings Flat back 630mm X 450 mm (six hundred thirty millimetre into four hundred fifty millimetre) as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

Providing and fixing vitreous China pedestal for wash basin complete recessed at the back for wash basin complete recessed at the back for the reception of pipes and fittings.as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

Providing and fixing C.P. brass waste of 32mm (thirty two millimetre) dia size for sink or wash basin.as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

Providing and fixing 600mm X 450 mm (six hundred millimetre into four hundred fifty millimetre) bevelled edge mirror of superior glass mounted on 6mm (six millimetre)thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brass screws and washers.as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and fixing 600mm X 20mm (six hundred millimetre into twenty millimetre) C.P. brass towel rail complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and fixing charomium plated brass soap dish of ISI marked Jal with C.P. brass brackets fixed to wooden cleats with C.P. brass screws as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and fixing C.P. brass bib tap with capstan head of ISI marked Jal 15 mm (fifteen millimetre) dia with capaston head as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and fixing C.P. brass pillar tap with capstan head of ISI marked Jal 15mm (fifteen millimetre) dia.as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and fixing wall mixing faucet for shower and bath with over head pipe ( 1210cm) (One thousand two hundred ten centimetre) and bath shower as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

Providing and fixing C.P. brass angle valve 15mm (fifteen millimetre) dia.as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

Providing and fixing PVC connection with brass union 45cm. (forty five centimetre) Long and 15mm (fifteen millimetre) dia as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and fixing C.P. brass full way valve with wheel of ISI marked Jal 15mm (fifteen millimetre) nominal bore as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and fixing in position water lifting pump (toollu pump) having 1.00 (one) horse power capacity of Kirloskar or equivilent make ISI mark including all necessary fitting required at site complee in all respect including carriage of material within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals

Construting manhole with RCC top slab in 1:2:4 ( one cement isto two sand isto four graded stone aggregate) 20mm (twenty millimetre nominal size) ,foudnation concrete 1:4:8 (one cement isto four sand isto eight graded stone aggregate 40mm (forty millimetre nominal size) in side plastering 15mm (fifteen milliemtre) thick with cement mortar 1:3 (one cement isto three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (one cement isto two sand isto four grade stone aggregate 20mm (twenty millimetre)nominal size finished smooth complete including curing and testing having inside size 800mmx800mm (eight hundred millimeter into eight hundred millimeter) and 500mm (five hundred millimetre) deep including C.I. cover with frame (light duty single seal pattern one) 455mm x610mm (four hunded fifty five millimetre into six hundred ten millimetre) internal dimension total weight of cover and frame to be not less than 38 kg (thirty eight kilogram )weight of cover 23 kg (twenty three kilogram) and weight of frame 15 kg (fifteen kilogram) with 23cm. thick brick wall of approved quality in cement mortar 1:3 (one cement isto three sand) as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

RASHID KHAN GOVT CONTRACTOR

ANKIT MAHAJAN

naveen kumar