PROVN OF CERTAIN MINOR AND REVENUE WORKS UNDER GE SATWARI

Amount

Surface dressing not exc 15 cm deep and getting out in any type of soil complete all as specified and directed.

Excavation in trenches in any type of soil, not exceeding 1.5m deep and 1.5m wide for foundation etc or manholes, piers , shafts etc not exceeding 10 Sqm on plan & not exceeding 1.5m in depth and getting out complete all as specified and directed.

All as per Ser item No 2 here-in-before but, depth exceeding 1.5m and n.exc 3.00m complete all as specified and directed.

Returning , filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and directed

Removing excavated material to a distance exc 250m but n. exc 500m & depositing where directed at a level n. exc 1.5 m above the starting point complete all as specified and directed.

M&L for plain cement concrete 1:4:8, type D2 (using 40mm graded crushed stone aggregates) as in foundation, filling & mass concrete complete all as specified and directed.

M&L for reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed .

M&L for reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for M&L for reinforced cement concrete M-25 (design mix) (using 20mm graded crushed stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies complete all as specified and directed.

M&L for reinforced cement concrete M-25 (Design mix), (using 20mm graded crushed stone aggregates) as in walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses complete all as specified.

M&L for use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of concrete foundation and plinth beams and similar work for fair finished concrete surfaces complete all as specified and directed.

M&L for use and waste of form work to sides of pillars,struts,piers and columns square/rectangular for rough finished surfaces complete all as specified and directed.

M&L for use and waste of form work to soffits of suspended slab such as roof slabs, not exceeding 200mm thick, horizontal or sloping for fair finished surfaces complete all as specified and directed .

M&L for use and waste of formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups , spacers and binders including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, using old size bricks, straight or curved on plan exceeding 6m mean radius , built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with old size sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed .

M&L for rendering 15mm thick in cement mortar 1:4 on brick work or concrete surfaces, surface finished even and smooth without using extra cement complete all s specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on brick work or concrete surfaces, surface finished even and smooth without using extra cement complete all s specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for sand filling under floor with washed and screened dry fine river sand including watering, well ramming and consolidation complete all as specified and directed .

M&L for preparation of new plastered surfaces of walls, & applying two coats of oil bound distemper over two coats of wall care putty of 1-2 mm thick each and one coat of primer complete all as specified and directed.

M&L for preparation of new plastered/ concrete surfaces of walls and applying two coats of weather proof acrylic emulsion paint over one coat of wall care putty of 1-2 mm thick and one coat of primer complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for hard core of gauge not exceeding 63mm using broken stone or boulders, deposited, spread and leveled in layers not exc 15cm thick, watered and rolled/rammed to a true surfaces complete all as specified and directed .

M&L for 25 mm thick plain cement concrete 1:2:4, type B-0, (using 12.5 mm graded crushed stone aggregate) as in sub base/ levelling course of floors, finished even and fair complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 , type C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection, laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. surfaces finished even and fair including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:2 complete all as specified and directed .

M&L for plain cement concrete 1:2:4 ,type B1(using 12.5mm graded crushed stone aggregates)as in lintels upto 1.5m clear span, window or door cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm in height, copings,side posts of precast jallies,benching etc. including slightly rounded or chamfered angles including necessary formwork complete all as specified and directed.

M&L for 7 to 8mm thick non skid coloured digital ceramic joint less tiles (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and poined in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed in cement motar 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured digital tiles,300x450x7 mm thick, as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colored cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for granite work(Z-Black) 16 to 18 mm thick (table rubbed and polished) in steps, jambs , pillars, window cills , cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match shade of granite over and including 15 mm thick screed bed in cement mortar 1:4 complete all s specified and directed

S&F pressed steel frames of size 105mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including mild steel hinges, 100 mm long , medium weright and 25 mm x 3 mm flat iron as in hold fast , tie bar including necessary fixing lugs, lock strike plate and fixing arrangement and making good the disturbed surfaces in cement mortar 1:3 or cement concete 1:2:4 type B-1 including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed.

S&F factory made prelaminated solid 18mm(+0.7mm) thick celuka PVC foam ply,glossy finish, one side prelam and other side plain of density 600Kg/cbm including 2mm thick edge banding tape of equal width to be fixed on all exposed edges for kitchen cabinet shutter/Wardrobe complete all as specified and directed .

M&L for plain 18mm (+0.7mm) thick celuka matt finish PVC foam ply of density 600Kg/cbm, for kitchen cabinet shutter/Wardrobe complete all as specified and directed .

S&F continuous (piano) hinges,30mm width, heavy duty, mild steel ,bright finish or electrogalvanised suitable for 19mm thick shutter complete all as specified and directed.

S&F steel fasteners of size 75 mm long, drilled and fixed to walls complete all as specified and directed.

S&F steel support of 50mm dia and 75mm length fixed with bolts at bottom of cupboard box complete all as specified and directed.

S&F stainless steel designer handle ( heavy type) 100 mm size, fixed in drawers or shutters of cupboards complete all as specified and directed.

S&F UPVC (SWR) type B pipes, 110 mm bore, single socketed, in any length with rubber ring joints fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed.

S&F UPVC (SWR) type B pipes, 75 mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F UPVC (SWR) type B pipes, 75 mm bore, single socketed, in any length with rubber ring joints fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed.

S&F UPVC (SWR) bends any radius, 75 mm bore complete all as specified and directed

S&F UPVC (SWR) bends with access door any radius, 75 mm bore complete all as specified and directed

S&F UPVC (SWR) bends any radius, 110 mm bore complete all as specified and directed

S&F UPVC (SWR) bends with access door any radius,110 mm bore complete all as specified and directed

S&F UPVC (SWR) floor trap plain with grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed.

S&F uUPVC (SWR), junction single, (single 'T') equal or unequal for 75 mm bore complete all as specified and directed

S&F vitreous china squatting pan, Orissa pattern, size 580 x 440mm white with integral foot rest, cast iron 'P' or 'S' trap of size 100mm, including provision of plain cement concrete bedding and connection to trap and to flushing pipe, anti syphonage pipe etc and making good the floors complete all a specified and directed

S&F vitreous china wash down water closet pan (pedestal pattern) white in colour including connection pipe to union of flushing cistern, inlet and overflow pipes, connecting only to flushing cistern, anti-syphonage pipe with PVC flush pipe of 32mm dia including plastic seat with cover, white in colour with mild steel chromium plated hinging and 'P' or 'S' trap device complete all as specified and directed

S&F 10 litres PVC, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float 32mm PVC 'L' bend and handle including brackets complete all as specified and directed

S&F Reinforced concrete pipes of size 150mm (internal dia),class NP-2 , laid, jointed and tested complete with collar complete all as specified and directed .

S&F vitreous china table top wash basin, size 600x480x150mm, rectangular shape , white, to be fixed on counter/ RCC slab including chromium plated waste coupling, 32mm waste pipe complete all as specified & directed

S&F single lever basin mixer without popup waste with 450mm long braided hose, fancy type complete all as specified and directed..

S&F brass chromium plated tubular rail 20mm dia, D type , 600 mm long between flanges fixed with CP brass screws including wooden/plastic beads complete all as specified and directed.

S&F sheet glass shelf assembly consisiting of 5.5 mm thick sheet glass, shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F corner glass shelf of size 30cm with Chromium plated bracket guard and railing fixed with and including screws and wooden/plastic cleats complete all as specified and directed .

S&F health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connectios and fixed in position complete all as specified and directed.

S&F bib tap with flange , chromium plated, fancy type, cast copper alloy , screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F angle cock with flange,cast copper alloy , fancy type, chromium plated, screwed down for high pressure with crutch or butterfly handle, screwed both ends for iron pipe of 15mm bore complete all as specified and dircted.

S&F Gun-metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe of 20 mm bore pipe, including making connections complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tanks of 1000 litres capacity (cylindrical vertical with closed top) with plastic lid cover, hoisted and fixed in position including PTMT Ball valves high pressure with epoxy coated aluminum rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe including making connections complete all as specified and directed.

S&F Galvanised steel tubing, 15mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling and laid in floors complete all as specified and directed

S&F Galvanised steel tubing, 20mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling and laid in floors complete all as specified and directed

S&F PVC connection 15 mm x 600 mm including brass check nut at both ends complete all as specified and directed.

S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to distributed surface of walls complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick ( style ) consisting of frame work made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour P.V.C‘ C’ channel having a PVC sheet strip 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap inserts for top rail; and bottom rail paneling of plain, colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rail with suitable PVC sheets beading and jointed together with solvent cement S&F in frame at site as per specification complete all as specified and directed.

S&F aluminium anodised barrel tower bolts, 150mm long of extruded section, fixed to doors with screws complete all as specified and directed.

S&F 100mm long mild steel butt hinges, medium weight ,fixed with screws complete all as specified and directed

S&F aluminium anodised , fabricated type handle 100mm size fixed to doors with screws complete all as specified and directed.

S&F aluminum alloy, anodised, sliding door bolt of length 250mm with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminum alloy and fixed complete all as specified and directed.

S&F aluminum powder coated (coating not less than 50 micron) window and ventilator shutters, side hung type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, necessary glazing and locking arrangements anodised aluminium fittings such as peg stays 150mm long (1 No.). 100mm long hinges type B-21(2 Nos.) suitable handle (1 No.) complete all as specified and directed

M&L for rendering 15mm thick in cement mortar 1:4 mixed with water proofing compound on roof surfaces , surface finished even and smooth without using extra cement complete all as specified and directed. Note:- water proofing compound will be measured and paid separately

M&L for water proofing treatment in the following sequences:- (a) Applying 1st course of bituminous primer confirming to IS-3384 @ 0.4 Kg/sqm .Cover the surface till the surface properly impregnated and insolvent oil primer evoporate completely. (b) Applying 2nd coat of blown 85/25 graded bitumen confirming to IS 702 @ 1.2 Kg/sqm. (c) Applying 3rd course of APP (Atactic Polypropylene) modified polymeric membrane 3 mm thick weight not less than 3.6 Kg/sqm with 160 Grams/sqm non woven polyster made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat complete all as specified and as directed (d) Complete treatment to be carried out by authorised applicator of waterproofing manufacturer.

M&L for applying two coats of aluminum paint over the APP membrane complete all as specified and directed.

Supply only Integral water proofing compound

M&L for factory made box type steel windows/ventilators, double shutter,outer frame made out ERW TUBE 'P section (60x45x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) openable shutters side hung including pintle hinges with two nos MS tower bolts 150mm size on each shutter, steel handle and stopper of 'Z' section as specified complete with sash bars dovetailed or welded ready for glass fixing and wire gauzed fixing with suitable fittings/opening for cooler/AC where required steel windows will be double shutter (external glazed and internal wire gauzed) complete all as specified in Drg No CEPZ/TD-324/07 of sheet No 1/3 to 3/3 complete all as specified and directed. Note: - The quoted rate shall be deemed to include :- (i) 04 Nos MS steel lugs of MS flat 20 x 5mm & 20 cm long over all welded to frames (ii) PCC block for embedding lugs.

S&F Mild Steel framed work such as grills, gratings etc. with ends of bars shoulderd and/or riveted, or forged into spikes, framed guard bars, barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks,cooler stand,ladder and similar work conforming to Fe290, Gde-E-165 complete all as specified and directed.

M&L for preparation of new or previously untreated steel surface of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M&L for machine pressed chequered cement concrete tiles 30cmx30cmx25mm thick, polished with grey cement and pigment, set , jointed and pointed in neat cement slurry as in floors, laid over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L for preparation of new plastered/concrete surfaces of walls and applying two coats of cement base paint over one coat of primer complete all as specified and directed .

M&L for 100 mm thick plain cement concrete 1:4:8, type D2 (using 40 mm graded crushed stone aggregates) as in sub base of floors, finished even and fair complete all as specified and directed.

M&L for 40 mm thick plain cement concrete 1:2:4, type B-0, (using 12.5 mm graded crushed stone aggregate) as in sub base/ levelling course of floors, finished even and fair complete all as specified and directed.

M&L for providing and laying 80 mm thick factory made charmfered edge cement concrete paver block of M-35 grade of approved colour, design & pattern as in foothpath, parks, lawns, drive ways or light traffic parking etc of required strength , thickness & size/ shape made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

S&F structural steel work in tubular trusses including special shaped washer complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed.

S&F Pre painted galvalume aluminium zinc coating (AZ-150 micron) GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified and directed .

M&L for plain cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregates) as in surface channel and drain including necessary form work and finishing top of benching even and fair complete all as specified and directed.

M&L for extra for forming fair finish drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds mitred/topped ends etc complete all as specified and directed.

M & L for Pre cast cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in manhole cover slab and likes, rounded or chamfered on edge included neccessary formwork, set in cement mortar 1:4 complete all as specified and directed ..

M&L for 8 to 9 mm thick vitrified ceramic coloured light shade tiles (square/ rectangular) polished area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm ,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed .

M&L for 8 to 9 mm thick vitrified ceramic coloured light shade tiles (square/ rectangular) polished area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm ,in vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed ..

M&L for aluminum powder coated (coating not less than 50 micron), sliding window, three track with stainless steel mosquito proofing with window style of section 44.4mmx44.5mmx 2.0mm thick and frame of section 101.60 x 44.45 mmx 1.20mm thickness including 4.0 mm thick coloured/tinted/frosted glass panes & stainless steel wire mesh of aperature 0.63mm and all necessary fittings and fixtures complete all as specified and directed.

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2) round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required (Internal Dia of pipe in 150mm) complete all as specified and directed.

M&L for PCC 1:2:4 type B 1 (using 20mm graded crushed stone aggregates) as in walls or, retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and directed .

S&F mild steel work such as in angle iron fencing posts, struts and flat iron fillets, gates etc, including drilling hole, punching,splitting ends to secure chain link fencing or fixing of barbed wire to posts including all necessary cutting, welding bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 quality complete all as specified and directed.

S&F mild steel screw bolts having dia of neck 5 mm to 10 mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut n. exc 5 cm long complete all as specified and directed .

Supply only mild steel galvanized chain link cold dip fencing of aperature 50mm x50mm complete all as specified and directed. Note: The weight of chain link fencing shall be ascertained by BOO as ordered by GE and payment shall be made accordingly and contractor shall have no claim on this account.

Fixing only chain link fencing including line wires(steel wire), any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire compete all as specified and directed Note:- Angle iron, flat iron and nuts & bolts shall be measured and paid separately.

S&F Galvanised, 2strand, steel barbed wire 2.24 mm dia, barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails, straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc. as directed (each line wire to be measured).complete all as specified and directed.

Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable(ISI marked) 1100 volts grade FRLSH with multistranded copper conductor, drawn through concealed / surface in wall / roof/ceiling surface and its accessories on the surface etc including PVC rigid concealed conduit ,medium grade,of suitable size with all accessories such as bend, reducers, MS hooks including galvanised/pressed steel moduar terminal boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc including continuous earth wire of size 1.5 Sqmm PVC FRLSH stranded copper conductor unsheathed, insulated, stranded connected to common earth point dolly for one light point/fan point/call bell point, 230 volts controlled by one switch complete all as specified and directed . Note:- Proper colour coding is to be followed as per IS specifications.-

All as per Srl item No 102. here-in-before but for one socket outlet, 3 Pin 5 Amps, 230 Volts on independent board complete all as specified and directed

All as per Srl item No.102 here-in-before but for one three pin socket outlet 5 Amp on the same board with other switches complete all as specified and directed

All as per Srl item No 102 here-in-before but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire complete all as specified and directed

S&F modular type switch, one way 6 Amps , 1 module complete all as specified and directed .

S&F modular type socket 3 pin, 6 Amps, 2 module complete all as specified and directed .

S&F modular type switch, one way, 16 Amps, 1 module complete all as specified and directed .

S&F modular type socket 3 pin, 6 A/16 Amps, 2 module complete all as specified and directed .

S&F ceiling rose, surface backelite, two/ three terminal, 240 volts complete all as specified and directed .

S&F LED light fitting 1 x 18Watt, 220V, Integrated batten type with driver, holder including LED tube light, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose with all fixing arrengenment complete all as specifieds and directed.

S&F energy saving new generation 10W LED bulk head luminaire with opal diffuser, IP 65 and including connecting up with twin core twisted flexible copper coductor cable with suitable size of 230 volt,50 Hz complete all as specified and directed.

S&F Sheet metal enclosure for DBs,SPN, double door,IP-43 protected, 230 Volts,8 ways with 100 amps rated copper bus bar complete all as specified and directed

S&F MCB Single pole, 6 to 32 Amp, 240 Volts with rupturing capacity 10 KA, 'C' series, complete all as specifieds and directed .

S&F MCB SPN, 32 Amp, 240 Volts with rupturing capacity 10 KA, 'C' series, complete all as specifieds and directed .

S&F exhaust fan, steel body, AC single phase. 230 V of size 300 m sweep with, blades and frame and louvers, hanging on wall with 4 Nos steel fasterners 10mm dia & 100mm long including wall hole and making good the disturbed surfaces as per existing complete all as specified & directed

S&F electric water heater of capacity 50 litres,BEE 5 Star rated,storage type, steel body vertical type with glass lined /porcelain enamel coated steel inner tank and glass line double ceramic heating element upto 2 KW complete with all accessories such as safety valve,thermostate NRV,connection piece etc and fixing with 04 Nos nut bolt grouting in wall in PCC(1:2:4) using 12.5mm graded stone aggregate for hanging the geyser and making good the disturbed surface complete all as specified and directed

M&L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1, precast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh ,15mm dia light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and directed ..

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 25 Sqmm, 2 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and directed.

M&L for sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment.

M&L for factory made unreinforced precast concrete cable cover LV type-1, flat, of size 250x150x40mm, laid flat and dry in trenches over the cable for protection, length perpendicular to the direction of cable adjacent to each other, complete all as specified and directed.

S&F Galvanised steeI tubing, light grade, 40mm bore, for cable protection, fixed to pole/wall with MS clamps, nuts, bolts etc or laid under floor/road/pavement complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 50 Sqmm, 3.5 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and directed.

M&L for cutting esisting cast iron/GI pipe in position for insertion of CI specials or GI fittings viz Tee, collar, bend or tail piece etc for upto 50 mm bore pipe including removing of blockage, cleaning of pipe line complete all as specified and directed .

S&F Galvanised steel tubing, 25mm bore, medium grade with all fittings, fixed to wall/ceiling and laid in floors complete all as specified and directed

S&F Galvanised steel tubing, 50mm bore, medium grade with all fittings, fixed to wall/ceiling and laid in floors complete all as specified and directed

S&F 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed .

S&F 50mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed .

M&L for construction of Valve pit of size 900mmX900mmX900mm (internal dimensions) with brick masonry construction including necessary excavation and earth work in any type of soil, 15cm thick PCC 1:3:6 type C-2 extended 15cm beyond extertal edges of brick work, brick work in cement mortar 1:4,15mm thick plastering in cement mortar 1:4 internally & flush pointing externally as the wor proceed, three coats of white wash, PCC coping in 1:2:4 Type B-1, MS frame made out of angle iron of size 40mmx40mmx6 mm grouted with anchor fasteners(04 Nos) of length not less than 15cm, MS sheet cover of 10SWG fixed to angle iron frame by means of hinges, welded to frame and painting with 2 coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces including handle and locking arrangement with one number 50 mm dia brass pad lock complete all as specified and directed.

S&F ceiling fan complete with blades,clamp, hooks and accessories, 230 V, 1200 mm sweep, min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC) with compatible regulator and fixing of hooks by anchor fastner including connecting from ceiling rose/connector with & including flexible copper cable of suitable size complete all as specified and directed .

Supply, installation, testing & commissioning air cooled , split unit air conditioner electric driven AC 230 V, 50 Hz single phase of capacity 1.5 TR, BEE 5 Star rated with cooling and intelligent heating facility and Digital Inverter twin rotary including its fixing accessories with following specification: (i ) Rated cooling capacity: 18000 Btu/Hr (ii) Rated Current cooling : 7.8 Amp (iii) Rated heating capacity: 18000 Btu/Hr, (iv) Copressor type: High EER twin Rotary (v) Anti dust/Anti-bacterial Filter, (vi) Dehumidifier (vii) Refrigerant gas: R32, (viii) noise level -33db (ix) Operation: LCD Remote with self dignosis facility all as specified and directed. Note: The quoted rate shall deemed to include powder coated stand (bracket) for fixing outdoor unit and cutting, chasing of wall/surface and making good as per existing.

S&F automatic boost/bulk transformer of capacity 5.0 KVA, for low & high voltage correction, equipped with electronic transistorized relay, suitable for correction on single phase, 50 c/s, AC supply complete with voltmeter and designed for input voltage 175 V to 250 V and output voltage 215V to 250 V complete all as specified and directed .

S&F Sheet metal enclosure for DBs,SPN, single door,IP-43 protected, 240 Volts,2 ways complete all as specified and directed

S&F Sheet metal enclosure for DBs,SPN, double door,IP-43 protected, 230 Volts,12 ways with 100 amps rated copper bus bar complete all as specified and directed

S&F MCB SPN, 40-63 Amp, 240 Volts with rupturing capacity 10 KA, 'C' series, complete all as specifieds and directed . .

S&F Submain wiring with two runs of single core PVC FRLSH unsheathed, insulated, copper cable of 4 Sqmm size, multi stranded, 1100 volts grade with PVC insulated,unsheathed FRLSH copper wire 4 Sqmm for continous earth wire drawn into and including concealed PVC conduit of suitable size complete all as specified and directed . Note :- Two runs of 4 Sqmm copper cable and one run of 4 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length)

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 16 Sqmm, 2 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 16 Sqmm, 4 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and directed.

S&F street light bracket fabricated out of GI tubing, medium grade, 40mm bore, bend to the shape as directed and of length 1.2 mtr complete with mounting MS clamp made of flat iron 25 x 3 mm of suitable length including nuts, bolts etc of suitable size and painting of MS clamps with two coats of aluminum paint over one coat of red oxide primer complete all as specified and directed .

M&L for LED Street lighting 60W LED IP66 New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium with lens and toughened glass type roadway luminaire with high power LEDs as light source including electronic driver 60W LED 6000K complete all as specified and directed.

Supply and fixing in replacement multi core round PVC insulated aluminium conductor (flexible) industrial cables PVC sheathed , 1100 volts of size 2.5 Sqmm, 3 core from junction box /overhead conductor to street light inside/outside pole complete all as specified..

Supply & fix thermoplastic polystyrene polycarbonate junction box of size 250 X 180 X 110 mm, shock proof with IP 66 protection with provision of all side cable entry through gland with suitable connector for three phase loop in loop out branch out and vibration proof connection and fixing on LT/HT poles using MS clamp made out of 25mm x 3mm MS flat (02 Nos) and nuts & bolts of required size complete all as specified and directed .

Supply & erecting in truly vertical position steel tubular swaged poles, type 410 SP-31(9.00 meters long) in replacement of UNSV /broken PCC poles, complete with cast iron base plate, finial taper plug, bolts, nuts & screws, including marking pole numbers & transformer number in a 15 cm dia yellow circle with number writting with black synenthic paint/ Stricker including painting strips in alternate from bottom to top with three strips of white synthetic enamel paint & two strips of Yellow/ black paint throughout the circumference of pole including one coat of lime wash on PCC copping of pole complete all as specified and directed..

S&F Submain wiring with two runs of single core PVC FRLSH unsheathed, insulated, copper cable of 2.5 Sqmm size, multi stranded, 1100 volts grade with PVC insulated,unsheathed FRLSH copper wire 2.5 Sqmm for continous earth wire drawn into and including concealed PVC conduit of suitable size complete all as specified and directed . Note :- Two runs of 2.5 Sqmm copper cable and one run of 2.5 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length)

S&F electric water heater of capacity 25 litres,BEE 5 Star rated,storage type, steel body vertical type with glass lined /porcelain enamel coated steel inner tank and glass line double ceramic heating element upto 2 KW complete with all accessories such as safety valve,thermostate NRV,connection piece etc and fixing with 04 Nos nut bolt grouting in wall in PCC(1:2:4) using 12.5mm graded stone aggregate for hanging the geyser and making good the disturbed surface complete all as specified and directed

S&F exhaust fan, steel body, AC single phase. 230 V of size 380 m sweep with, blades and frame and louvers, hanging on wall with 4 Nos steel fasterners 10mm dia & 100mm long including wall hole and making good the disturbed surfaces as per existing complete all as specified & directed

M&L for cutting of wall of any thickness for fixing of exhaust fan of sweep 380 mm and making good the disturbed surfaces as per existing complete all as specified & directed

M/S SHAKTI STEEL INDUSTRIES (BID ID -3378927)

M/S S S Engineers (BID ID -3378843)

J P TECHNO (BID ID -3374632)

M/S PARAMJEET SINGH (BID ID -3384531)

M/S VED PAUL MAHAJAN (BID ID -3378900)