REPAIR TO HELIPAD CRACKERS JOINT FILLING DAMAGED DRAIN SLABS AROUND HELIPAD BOUNDARY WALL SECURITY FENCING PAINTING DISPERSAL AREA PAINTING OF ATC HANGERS CLEANING OF DISPERSAL AREAS AND AIR FIELD LIGHTING AT INS SHIKRA UNDER GE NW NOFRA COLA

Amount

Material and labour for preparation of surface, 50mm depth of cutting damaged portion of PQC slabs 50mm depth such as edges of joints and cracks not less than 50mm on either side of edge of concrete slab, to remove all the damaged, loose and unsound concrete by the help of Electric / diamond tool cutter of appropriate geometrical size in order to have straight and smooth edges, inside of the cut concrete surface shall be made rough for proper mechanical anchorage and cleaned with hard wire brush to remove all loose particles and vacuumed cleaned to have a dry and dirt free surface, prior to mixing and placing the elastomeric concrete, prime the substrate coming in contact with the elastomeric concrete both vertical and horizontal surface should be primed with special primer RDL 942 the material shall be applied using a paint brush and in a single coat. Flex O Patch (Elastomeric concrete), kits contain 3 kg of part A and 1.5 kg of part B with a 5.5 Kg.part of part C (E-Crete Aggregate) using a drill and spiral mixing paddle, pre-mix A & B components until uniform (approx 60-90 seconds) immediately remove contents from C and add to the above and continue mixing until no dry material appears once mixed, the material can be poured into the block out/hole while the primer is still wet the material is self leveling trowel finish as desired.(Make : Pidilite/ Dr fixit /Ultra Tech / Choksey / Fosroc) Note :- 1. The quoted rate for the above item shall be deemed to include disposal of debris to the outside of MD Land. Curing of the repaired joints, removing of the thermocol and cleaning of the concrete surfaces etc complete all as directed by the Engineer-in-Charge. 2. The work shall be carried out through an authorised applicator of the company and certificate is required. 3. Contractor has to submit bank guranatee of 30% of amount quoted by him for five years against this item towards defects rectification. 4. Due care shall be given to avoide any damage to the existing lighting system as this is related with landing & take off of Helicopter etc and any damage if happened, noted the same shall be rectified immediately to the satisfaction of GE.

Material and labour for racking out damaged/deteriorated old sealing compound 25 to 30 mm wide & 40mm average depth of existing expansion joints with air blower and filling with 30mm dia polyethyelene rod and balance gap with polyurethane joint sealient upto top surface (suitable for old rigid pavement) including applying suitable primer for proper bonding with polyurethane joint sealient etc complete and all as specified. Make : Pidilite/ Dr fixit / Choksey / STP / Fosroc

Material and labour for racking out damaged/deteriorated old sealing compound upto 15 mm wide & 30 mm average depth of existing consturction/dummy joints with air blower and filling with 12mm dia polyethyelene rod and balance gap with polyurethane joint sealient upto top surface (suitable for old rigid pavement) including applying suitable primer for proper bonding with polyurethane joint sealient etc complete and all as specified. Make : Pidilite/ Dr fixit / Choksey / STP / Fosroc

Material and labour for racking out damaged/deteriorated old sealing compound 25 to 30 mm wide & 30mm average depth of existing expansion with air blower ( if required) priming the joints surfaces with Primer & sealing the joints with polyurethane joint sealient (suitable for new rigid pavement) all as specified and as directed by Engineen-in-Charge and also included disposing the debris as obtained from demolition to the outside of MD land. Make : Pidilite/ Dr fixit / Choksey / STP / Fosroc

Material and labour for racking out damaged/deteriorated old sealing compound upto 15 mm wide & 30mm average depth of existing construction/dummy joints with air blower ( if required) priming the joints surfaces with Primer & sealing the joints with polyurethane joint sealient (suitable for new rigid pavement) of all as specified and as directed by Engineen-in-Charge and also included disposing the debris as obtained from demolition to the outside of MD land. Make : Pidilite/ Dr fixit / Choksey / STP / Fosroc

Material & labour for cleaning the existing drainage/culvert including removing cover slab,soils,spoils,vegetation,silt etc and refixing cover slab making good and removing waste materials outside MD Land complete all as directed by Engineer-in-Charge.

Material & labour for cleaning the dispersal area with brooming down/steel wire brushing/washing to remove all dirt, dust, loose particles and any other deleterious materials etc including scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots by employing two unskilled labour per day for each job consisting of minimum area 400 sqm all as directed by Engineer-in-Charge

Removing old paint by paint removers or burning off by blow lamps and cleaning with scrapers any nos of coats , any width or girth as specified and directed by the Engineen-in-Charge

Material & labour for preparation of old painted concrete surfaces (Rigid Pavement) over 10cm width or girth and apply two coats in 24 hour interval with water based road marking paints conforming to IS-164, 1981(Amended 1993) , fast drying,highly durable 100% acrylic retro-refective water borne paints applied with spray machine to lines, dashes, arrows, letters etc & the like, exceeding 10cm wide with road marking paint & tint as approved & as specified (Painting shall be done by using wooden/plywood template at edges to be provided). First time painting. Make:Apcotrak from Asian paints or equivalent

All as per item No 09 above but one coat for second time painting for the same area after three months gap from first time painting.

All as per item No 09 above but one coat for third time painting for the same area after three months gap from second time painting.

All as per item No 09 above but one coat for forth time painting for the same area after three months gap from third time painting.

Material & labour for preparation of old painted concrete surfaces (Rigid Pavement) as in lines, dashes, arrows, letters etc & the like not exceeding 10cm wide apply two coats in 24 hour interval with water based road marking paints conforming to IS-164, 1981(Amended 1993) , fast drying,highly durable 100% acrylic retro-refective water borne paints applied with spray machine to lines, dashes, arrows, letters etc & the like, exceeding 10cm wide with road marking paint & tint as approved & as specified (Painting shall be done by using wooden/plywood template at edges to be provided). First time painting. Make:Apcotrak from Asian paints or equivalent

All as per item No 13 above but one coat for second time painting for the same area after three months gap from first time painting.

All as per item No 13 above but one coat for third time painting for the same area after three months gap from second time painting.

All as per item No 13 above but one coat for forth time painting for the same area after three months gap from third time painting.

Material & labour writing letters or figures (Block,Roman,Italic/Arabic) n.exceeding 30 cm high and apply two coats in 24 hour interval with water based road marking paints conforming to IS-164, 1981(Amended 1993) , fast drying,highly durable 100% acrylic retro-refective water borne paints applied with spray machine to lines, dashes, arrows, letters etc & the like, exceeding 10cm wide with road marking paint & tint as approved & as specified (Painting shall be done by using wooden/plywood template at edges to be provided). First time painting. Make:Apcotrak from Asian paints or equivalent

All as per item No 17 above but one coat for second time painting for the same area after three months gap from first time painting.

All as per item No 17 above but one coat for third time painting for the same area after three months gap from second time painting.

All as per item No 17 above but one coat for forth time painting for the same area after three months gap from third time painting.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, as in valley gutter, ridge of roof, wall and cladding etc

Dismantling structural steel work wrought iron or mild steel work including door, gates, of any description not otherwise provided for

Supply & fix of Rolled sections of Fe-410-W (Gde-E-250) quality-B as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates

Supply & fix as in repairs plates (plain or corrugated) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410(Gde-250)

Supply & fix Mild screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 5 but not exceeding 10 cm long dia of shank 11 to 15mm.

Supply & fix Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, chajjas, fixed with self tapping screws as specified.

Supply & fix Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in ridge of roof covering/ cladding to wall, chajjas, valley gutter, fixed with self tapping screws as specified.

Material & labour for preparation of new steel surfaces exceeding 10 cm in width or girth and applying 2 coats synthetic enamel paint over a coat of pink primer.

Material and labour for cutting of PQC slabs of depth not exceeding 15cm by the help of electric/diamond tool cutter of appropriate geometrical size in order to have smooth edges the inside of cut concrete surface shall be made proper vertical finishing and cleaned with hard wire brush to remove all loose particles and vaccumed cleaned to have a dry and dirt free surface and removal of debris out side of MD land all as specified and directed by the Engineer-in-Charge

Material and labour for micro concrete for filling concrete surface made rough for proper mechanical anchorage. the surface shall be further cleaned with suitable 'solvents' for a clean stable surface and preparing and applying Epoxy Bond Coat (Fosroc Nitobond EP or equivalent) inclusive of Base and hardner brushed and worked well on the old concrete of M-50 grade (Renderoc RG of Fosroc or equivalent) to form rigid edges of joints. Note :- (a) The hardening edges of the joints to be repaired shall not be less than 35mm in depth. (b) The work shall be carried out through authorised applicator only

Material and labour for applying one coat of primer to vertical and horizonatal surface with special primer RDL 942 or equivalent using brush and filling of flex-o-patch, (Choksey) a self leveling three component a modified urethane system as Part-A (3Kg) and Part-B (1.5Kg) and Part-C (5.5 Kg) using a drill and spiral mixing paddle, pre-mix A&B components until uniform (Approx 60-90 seconds) no dry material shall appear and once poured into block out/hole while the primer is still wet mix with tremendous physical properties allowing elastomeric concrete to detect under load without destroying it's matrix and finished with trowel as specified by the manufacturer's instruction and as spcified by the Engineer-in-Charge.(Make : Choksey/fosrac/STP Ltd/Pidilite/SIKA or Equivalent) Note :- The work shall be carried out through an authorized applicator of the Company.

Demolition of pre-cast RCC of any description and in any position not otherwise specifically provided for as in drain covers

Material & labour precast RCC (1:1.5:3) A-1, using 20mm graded stone aggregate as in cover slabs for drains etc including necessary form work of any size & thickness and also making holes in precast slab in a standard pattern as per requirement and as directed by EIC etc complete, set and jointed in CM (1:4).

Material & labour for PCC (1:2:4), type B-1, using 20mm graded stone aggregate as in cills, copings, benching,bed plates, water troughs and the like including weathering , slightly rounded or chamfered angles and throating, etc complete including necessary form works

Material & labour for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia. or securing with clips

All as per item No 35 above but 8mm dia.

Material & labour for mild steel TMT bars 5 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia. or securing with clips as in stirrups, spacers and binders, complete all as specified.

Demolition of reinforced cement concrete of any description and any position, complete all as specifed & directed.

Material & labour for rough finished square or rectangular Formwork to sides of pillars, posts, struts, piers, columns and stanchions, complete all as specified.

Material & labour for reinforced cement concrete (nominal mix) type B1 (1:2:4) in columns, pillars etc. complete all as specified & dirceted.

Dismantling of wrought iron or mild steel work of any description

Supply & fix framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-290 (Gde-E-165)

Material & labour MS framed work such as grills , gratings, etc., with ends of bars shouldered and/ or riveted, or forged in to spikes; framed guard bars ;ladders; framework of water tanks and similar work conforming to Fe-290, Gde-E-165

Material & labour for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified.

Material & labour for Cleaning of static tank of 40,000 Ltrs and above size by dewatering with pump/manual, removing all scale, liquid waste and dirt etc from the static tank to the outside of MD land and cleaning the static tank with fresh water etc complete all as specifed and directed (A notice board to be erected near buried position to identify and to avoid any accident as directed by Engineen-in-Charge).

Removing old lime wash, hacking for key , raking out joints of old brick work or stone work built in old brick work or stone work built in cement mortar; not previously plastered; and scrubbing down with water etc. to receive plaster

Material & labour rendering (15+5) 20 mm thick in CM (1:4) stone surface of walls finished the surfaces even and smooth & mixing of integral WPC in 2nd layer (5mm thick) etc complete (integral WPC will be measured separately).

Supply only integral water proofing compound.

Material & labour for preparation of newly plastered surfaces of walls, chajjas, parapets, pilasters etc and applying two coats of acrylic emulsion exterior weather proof paint (100 % Acrylic) on external surfaces over a coat of primer complete all as per manufacturer's instructions.

Material & labour for preparation of old plastered surfaces of walls, chajjas, parapets, pilasters etc and applying one coats of acrylic emulsion exterior weather proof paint (100 % Acrylic) on external surfaces complete all as per manufacturer's instructions.

All as per item No 50 above but second time one coat of acrylic emulsion exterior weather proof paint (100% Acrylic) for the same area after six months gap of first time painting.

Dismantling interlocking tiling, removing serviceable tiles to store and disposing the rubbish to the out side of MD land

Material & labour for PCC (1:1.5:3) type A-O, interlocking tiles gloosy finish coloured of approved design/pattern, 60mm thick laid over and including fine sand cushion not less than 25 mm thick to a line surface, slope etc and joined complete also including spreading screened river sand over surface for filling the joints with rising surface vibrator etc complete all as specified and as per manufacturers instructions and directed.

Taking down interlocking tiles from existing surface and Material & labour for refixing the same place after necessary fill the PCC in lower portion and laid over and including fine sand cushion not less than 25 mm thick to a line surface, slope etc and joined complete also including spreading screened river sand over surface for filling the joints with rising surface vibrator etc complete all as specified.

Supply and fix stainless steel (SS-304) wind turbine air ventilator of 600 mm throat dia with capacity of 2700 cfm to be mounted on top of FRP base plate of 2 mm thick with venture dome, including necessary cutting of existing roof sheets, sealing with watertight arrangements etc complete all as specified and directed by Engineen-in-Charge. Make :- Mbient turbo or Equivalent

Material & labour for scarification of concrete surfaces at lower level till a depth of 25mm from top surface at a width of 3m, thorough cleaning of scarified surface by water jet. Apply of epoxy- based bonding agent on scarified surface & provide a separation joint with suitable closed cell backup material of 15mm width. Nosing at higher level side to existing level with fibre reinforced grout/ micro-concrete with strength not less than 60Mpa. Casting of M-40 grade fibre reinforced concrete flush with higher level on one side and existing level on the other . After curing period, cutting the separation joint at a depth of 15mm and finishing the same with suitable polysulfide or PU sealent post primer application. All work is carried out under the instructions & supervision of authorised applicator of pidilite.

RAJU AND CO

SHREE JAGDISH FURNITURE CO.