FURNISHING WORKS OF CPEPA SMART CLASS ROOM IN SCHOOL OF ECONOMICS SECTION AT DAVV KHANDWA ROAD , INDORE

Amount

Contractor/ Firm has to make 3 D plan of smart class room for colour approval and also provide Student Desk & Chair furniture sample for approval with tender submission.

Providing and fixing at all height false ceiling of 12.5 mm thick tapered edge gypsum board conforming to IS: 2095 including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanized in accordance with zinc coating 600 as per IS: 277 and consisting of angle cleats of size 25 mm wide X 15 mm thick with flanges of 22 mm and 37 mm at 1200 mm centre to centre one flange fixed to the ceiling with dash fastner 12.5 mm dia X 40 mm long with 6 mm dia. Bolts to the angle hangers of 25 X 25 X 5 mm of required length, and other end of angle hanger being fixed with nuts and bolts to 6.1 channels 45 mm X 15 mm X 0.9 mm running at the rate of 1200 mm centre to centre to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450 mm centre to centre shall be fixed in a direction perpendicular to 6.1 channel with connecting clips made out of 2.64 mm dia. X 230 mm long 6.1 mm wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre with 25 mm long drive – all screws @ 230 mm interval including joining and fixing to a flush finish of tapered and square edges of the gypsum board with recommended filler, paper tapes, finished and two coats of primer suitable for gypsum board as per manufacturers specification and also including the cost of making openings for light fittings, grills, diffusers,

Grid Ceiling Providing and fixing 15mm thick of approved texture with required groove approved by architect false ceiling tiles of Armstrong/Saint Gobin India Gypsum of size 600x600mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel section ( galvanised @ 170 gms/sqm.) consisting of main T runner suitably spaced at joints to get required length and of size 24x38 mm made from .3mm thIck. sheet spaced at 1200mm c/c and cross T of 24x25 mm made of .3mm thIck. sheet 1200mm long spaced between main T ant 600mm c/c to form a grid of 1200x600 and a secondary T of length 600mm of size 24x25 made of .3mm thck. sheet to be interlocked at middle of the 1200x600mm panel to form a grid of 600x600mm and laying of 15mm thck. mineral fiber ceiling tiles of approved texture in the grid including where ever required cutting/making opening for services like difusers, A.C grills, light fixture, smoke dectoters etc.Main T runner to be suspended from ceiling using G.I slotted cleats fixed to the ceiling with 6mm dia. and 50mm long dash fasteners,

P/F WOODEN LAMINATE FALSE CEILING Providing and fixing at all height false ceiling of 12 mm thick MR garde plyboard including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanized in accordance with zinc coating 600 as per IS: 277 and consisting of angle cleats of size 25 mm wide X 15 mm thick with flanges of 22 mm and 37 mm at 1200 mm centre to centre one flange fixed to the ceiling with dash fastner 12.5 mm dia X 40 mm long with 6 mm dia. Bolts to the angle hangers of 25 X 25 X 5 mm of required length, and other end of angle hanger being fixed with nuts and bolts to 6.1 channels 45 mm X 15 mm X 0.9 mm running at the rate of 1200 mm centre to centre to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450 mm centre to centre shall be fixed in a direction perpendicular to 6.1 channel with connecting clips made out of 2.64 mm dia. X 230 mm long 6.1 mm wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre with 25 mm long drive – all screws @ 230 mm interval including joining and fixing to a flush finish. The wooden ceiling will be finished with the approved 1MM laminate as per directions and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed finishing of all joints neatly to proper line & level including providing of additional framework for electricals fixtures.including giving trap doors where ever required.Diffusers, cutouts for fire sprinklers etc. as per the specifications approved by architects Including necessary scaffolding supports, suspenders etc. All complete as per drawing and specification and direction of the architect.

Providing and fixing AUDITORIUM Hall Stage in 18 mm BWP ply of ht 450 mm , L profile, Skirting & Reducer etc. complete. Only Top will be measured

Providing and fixing AUDITORIUM Hall steps in 18 mm BWP ply of Avg Ht 525mm at center , L profile, Skirting & Reducer etc. complete. Only Top will be measured

Providing and fixing in position imported carpet of approved shade and brand 550 GSM PILE WT , GROSS WT 1800 GMS, Graphic loop pile having thickness 7mm-9mm with primary backing of polypropylene wooven sect and secondary action back, complete as per drawings, specifications and as per the direction of architect.Carpet and underlay to be installed with standard fevicol/Dunlop adhesives.The flooring to be installed as per manufacturer’s specifications and to be installed by its authorized agency or as approved, with eighteen months warranty from principals from any manufacturing defects.The installation to be in line and level including the cost of all materials, disposal of debris etc, complete to the satisfaction of architect.(Inclusive of profile)

Providing and fixing paneling on wall, on G.I hat furring channel 22-25 depth with grid size 600mmx 600mm both ways fixed to wall, columns in any profile and covered with 8mm. plywood of approved make and finished with 1mm laminate as approved on exposed faces with grooves as per design.The rates shall include all hardware, fittings, adhesives, beadings, lippings etc. as directed by the architect.

Providing and fixing paneling on wall, on G.I hat furring channel 22-25 depth with grid size 600mmx 600mm both ways fixed to wall, columns in any profile and covered with 12.5mm perforated gypboard of approved make and glass wool and finished with 10mm acoustical pet panels as approved on exposed faces with grooves as per design.The rates shall include all hardware, fittings, adhesives, beadings, lippings etc. as directed by the architect.

Providing and Installation of acoustical polyester fiber panels of thickness 10 mm on wall with an option of colors as per the choice of the Architect/Engineer in charge. It shall be fixed on walls as per suitable arrangements and as suggested by the engineer in charge.

Providing and fixing Ist ClassTeak wood/Rubeer wood skirting wherever required as per carved profile of size 75mm widex15mm thick duly melamine polished.Fixing details as per drawing and as directed by architect.

Providing and fixing Ist ClassTeak wood/Rubber wood beading of size 25mmx15mm(max)or as per profile duly melamine polished complete as per details, drawings and as directed by architect.

Providing and fixing of Venetian blinds Both side Coated with Blackout Fabric, Coating is of PU. Max. Width 2.50 M; with mooth operating roller rods of approved shade and quality

Providing and fixing black out roller blinds Vista/Mascot make and shade with hanging and drawing system including all hardware and fixing complete.

P/F Acoustical doors in position with proper line and level.The shutter shall consists of CP-II wood inner frame 40x40mm with top, bottom and lock rail and covered with 1mm laminate in inner side with 8 mm distance between two slates &12 mm ply with 1 mm laminate from outerside ..The shutter shall be fitted into ply door frame.The shutter and door frame shall be finished with 1mm laminate of approved shade and make.The door shall be fitted with 4 nos heavy duty brass hinges and stainless steel handle and imported door closer complete lock arrangement etc.

Providing & fixing flush door. Frame made out of with ply of thickness 30mm, with lock handles, hinges, stopper , tower bolt, door closures etc. complete of approved quality . The ply is finished with 1 mm thick laminate from both sides. . All exposed wooden members to be finished in Melamine polish, in approved shade and pattern to be match with partition or as as per instruction.

Painting of Acrylic emulsion paint on wall surface of approved brand and shade of approved colour in two or more coats including , two or more coat of ready made putty to give a smooth shade to the satisfaction of an architect.

Providing and applying vinyl coated wall paper of approved brand and finish as per the architects specification including scaffolding cleaning etc., at all levels and location etc, complete as directed and approved by architect.

Providing and fixing plain glass with edge polish of sizes 12mm thickness as per design, drawing, complete to the satisfaction of architect.

Canvass Paintings - with stretched framing

ARTIFICIAL PLANTS Providing and fixing artificial plants of Exotic flora pvt ltd/approved make.

Providing and installing of removable type aluminium false ceiling system for horizontal inclined and vertical comprising of square edge plane panels , 84mm wide x 15 mm deep with 25mm recessed flanges, formed out of 0.5 mm thick aluminium alloy electrically powder coated in standard colour shades as approved by Engineer In Charge. The panels shall be fixed on formed carriers, 15 mm wide at top 43 mm deep made out of 0.19 mm thick aluminium alloy electrically powder coated in stain black with protruding ears to hold panels in module of 100 mm, with 16 mm gap between the panels , carrier spacing shall be maximum 1.3 M c/c. Carriers to be suspended from the slab or roof by 4mm dia. galvanised steel wire or rod hangers with height adjustment suspension springs made out of galvanised spring steel. Hangers shall be fixed to roof or slab by J-hooks and nylon inserts. Edges of the ceiling shall be neatly trimmed with suitable matching edge profiles to cover the gap between the false ceiling and the walls.

Providing and installing Accoustical and thermal insulation blanket of 25 mm thickness of resin bonded mineral wool covered in polythene bags shall be laid over the aluminium panel ceiling.

Providing and fixing decorative laminate as per Iswith marine grade PVA glue ( fevicol ) applied @ 0 .45 kg per sq mtr to partition , paneling , roof beam or similar places as directed in design and pattern having pin groove (2.10.4) 1.0 mm thk textured finish

Providing and fixing clear heat reflective float glass to partitions, fix glazing, including polishing of edges and filling od gaps with silicon sealent as directed by engineer in charge (2.17.5) 12.0 mm thk

Extra for toughneneing and heat sheilding (2.18.5) 12.0 mm thk

Supply & fixing of matt finish, green painted 8 mm thick glass chalk board with 8 mm thick BWR Ply wood backing, to be fixed on wall in position with alaround teak wood frame work including melamine polish complete

Providing, fitting & fixing pelmet consisting of 19 mm thick block board, 225 mm wide top and 200 mm wide vertical drop with exterior face finished with decorative veneer, including lipping at top & bottom with 25 x 12 mm teak wood bead and fixing to the wall with heavy duty stainless steel hardwares. The veneer surface shall be finished with melamine polish, all complete as per drawing & direction of Engineer-in-Charge/Architects.

fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free straight, mitred and jointed mechanically wherever Aluminium Work required icluding cleat angle, Aluminium snap beading for glazing /paneling C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing and paneling to be paid for separately. (4.13.2) Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron

Providing and fixing clear float glass ( having U value less than 3.75 ) to partitions / window or as directed including polishing of edges and filling of gaps with silicon sealent ,epdm gasket of suitable sizes making holes etx as required (4.14.2) 5 .0 mm thk

Providing and applying of silica base synthtic resin (marketed under the name apex duracast, spectrum rustic finish , acrotex ) base texture coating/ plaster to external wall 3 mm thk at all level i/c coat of sealer, primer on cement base putty / Prepared levelled surface as per manufacturers specification and as directed,cost of scafolding etc as required texture applied in design and pattern of brick or other texture as directyed by engineer incharge

Providing and fixing wall panelling consisting of G.,I channels & stud of G.I sections of prime quality cold rolled steel as per IS:513 hot dipped galvanised 120 gsm as per BS 2989 to be fixed on wall with nylon sleeves to form rigid & proper frame work, 50 mm thick & 24 kg/cum density glass wool to be inserted in cavity of frame. The frame will be covered by 20-25 mm thick microfibre (soft board) (Anutone/equivalent make) sound soak panel of 1200 x 600 mm comprising of NRC 0.9), to be fixed on channel with the help of stainless steel screws at every 250 mm distance interval and 10 mm away from the edges of tiles for proper holding the tile with the G.I frame work in line & level as per specification and direction of Engineer-in- Charge and as per manufacturer's specification.

Supplying and fixing in position vertical blinds made with 100 mm wide fabrics of approved quality, make and shade assembled on top aluminium frame (33 mm x 28 mm x 1.2 mm) with powder coated (approx 50 micron) with high quality nylon runners with auto clutch mechanism, stainless steel master runners, stainless steel fitter chains and PVC end covers. The bottom end of the fabrics are suspended with a weight which are to be connected by link chains. All complete as per manufacturer's specifications. (4.18.1) 100 mm strip

Providing and fixing TW panelled door shutters using TW Styles and Top rails in TW section of 100 mm and Middle rail to be 150mm and bottom rail to be 200 mm size. The panel insert shall be 12 mm thick marine water proof one side Teak face finished ply of superior make and matching grains. The rate includes cost of all heavy duty 4 nos 100 x 35x35 SS bearing hinges & screw of approved quality heavy duty brass door stopper. The rates shall include all material, labour, hardware, wastages, cost of polishing etc complete. (4.3.1) 30 mm thk

CASETTE AC :- Supply installation testing and commisioning of split type cassette slim line / floor standing air conditioning unit of capacity including indoor outdoor unit fittedwith rotarycompressor copper condensor and forst charge refrigerent R410A/eco friendly green gas only, cordless remote control, auto air swing louvers, connection copper lead wire between outdoor and indoor unit connection copper lead upto 1.5mtr. excluding connection copper pipe of required size insulation floor stand for outdoor unit condense water outlet complete etc as required outdoor / indoor unit should be of same make(Brand) (4.13.1) Ceiling suspended/ mounted cassette type 4 way unit with inbuild drain pump & decorative panels (4.13.1.1) 1.8 TR / 2.0 single phase MAKE - SAMSUNG WITH 410 GAS , SIZE 3 X 3 FT

(4.13.1.3) 2.7/3.0 TR Three Phase

AC Installation :- Installation of split type Ceilling cassatte air conditioning unit including indoor outdoor unit fitted with rotary compressor, condensor and firsdt charge refrigerant R410A/ eco friendly green gas only including connection of copper pipe and material supplied with complete unit etc as required (Excluding copper pipe)

Supply, ionstalltion, testing & commissioning of suction/ discharge copper pipe line in slipt air conditioning unit 1.0/ 1.5 TR / 2TR / 3TR Capacity including brazing, nitrile rubber insulation 6/9mm thickl class '0' etc acomplete as required (4.3.1) Copper Tube 1/4"

Copper Tube 5/8"

Control Cable :- Supply and laying testing & Commitioning of following sizes of Copper Conductor Control Cables on existing Tray including fixing Clams & proper connections to equipment etc Complete as required (4.38.1) 2C X 0.75 Sq.MM

4C X 2.5 SQMM

Drain Piping :- Providing and Fixing of CPVC 6Kg/cm2 drain water piping with fitting support and insulated with 6MM Thick closed cell elastomeric nitrile rubber insulation complete as per specification (4.28.1) 20mm Dia ID

MS STAND FOR ODU CASSETTE AC FLOOR MOUNTED 2 TR

MINOR CIVIL WORK RELATED TO AC WITH CORE CUTTING AND FREIGHT

Supply, Installation, testing and commissioning of light point, exhaust fan point , wall fan point with 1.5 sq. mm. copper wire (for phase,neutral earth wire)1.1KV grade PVC insulated (including supply of all material like hardware , GI boxes , conduits ,modular switches,accessories.Point Length 7 Mtr

Supply, Installation, Testing and commissioning of light points in group control system including 1.5 sq. mm copper flexible 1.1 KV grade insulated wire (for phase,neutral earth wire),modular switch, switch board, conduit and material.Neutral & earthing can be looped on points for one light point. 2 Lights controlled by 6A switch.

3 Lights controlled by 6A switch.

Supply, Installation, Testing and commissioning of Bell/Buzzer point including 3*1.5 sq. mm copper 1.1 KV grade insulated, conduit, bell, buzzer and material.Including CPL buzzer board

Supply & Installation of 1.6mm thick MMS FR grade ISI conduit of approved make with accessories like heavy duty pull boxes with covers, GI saddles, bends, socket etc. in concealed/surface manner in wall, ceiling, floor etc. The work includes chiseling of wall i.e. ziri with mechanical cutter, saddling of conduits at maximum 400 mm distance etc.

DIA 25mm conduit

DIA 32mm conduit

Supply, Installation, Testing and commissioning of following size flexible copper wire 660 V/1.1 KV grade of approved make PVC insulated in existing PVC conduits , pull boxes , hardware etc.

2*1.5 sqmm (P&N) + 1*1.0 sqmm (E)

2*2.5 sqmm(P&N)+1*1.5 sqmm (E) ( FOR Switchboards and power)

2*4 sq.mm(P&N)+1*2.5 sq.mm (E) ( for AC)

1*10 sq.mm(E)

Supply, Installation, Testing and commissioning of 6A 5 pin switch and socket outlet on separate board (including supply of all material like MS box, switch, socket and hardware etc).The socket shall be suitable for international connectors and shall be approved from client before instllation.

3 no. 6A socket and 1 no. 16A switch on separate board( for computer power) .

Supply, Installation, Testing and commissioning of 6A switch/socket outlet on switch board (including supply of all material like MS box, switch, socket and hardware etc).Including wiring between switch and socket.

Supply, Installation, Testing and commissioning of 16A single phase switch and 16A 5 pin socket (including supply of all material like MS box, switch, socket and hardware etc). Including wiring between switch and socket.

Supply, Installation, Testing and commissioning of 20A industrial socket, 20A pin top and 20A SP MCB with box and the box shall be concealed in wall. The box also shall be of respective make of MCB. Including wiring between switch and socket.

8 Module Pop up Boxes for Conference Table complete with mounting arrangement

4 Module Pop up Boxes for Conference Table complete with mounting arrangement

Supply and laying of cables in excavated trenches, concrete trenches, along walls, through hume pipes, cable trays etc

4CX16 SQMM AL.AR XLPE CABLE

4CX4 SQMM CU.AR XLPE CABLE

Cable termination of armoured cables 1.1 KV grade including supply & installation of cable glands, cable lugs (copper or aluminium single compression type), heat shrinkable sleeves on long ends, crimping paste etc. (One set includes termination of all cores of one end only)

4CX16 SQMM AL.AR XLPE CABLE

4CX4 SQMM CU.AR XLPE CABLE

Supply, Installation , Testing & Commissioning of following lighting fixture and fan. All fixtures should be complete with all accessories.

LED fitting 38W PHILIPS/WIPRO MAKE 2X2 complete with all accessories.

Down light fitting 12/15 Watt LED complete with all accessories MAKE - WIPRO/PHILIPS/BAJAJ

Recess Mounted 1x6/3/2Watt LED Spot Light complete with Driver

LED Rope light 5Watt / meter with Driver/ controller

Supply and Installation of Wall Fan 16"

Supply and Installation of Celling Fan 1200 mm swip

Supply & installation of EXHAUST 300 MM

Supply & Installtion of Fan regulatore

Supply , installation, testing commissioning of 8Way VTPN DB With 63 Amp 4Pole MCB as incomer and Tp 32/40 amps 4 nos SP Mcbs 12 nos For outgoing.6 to 32 amps Main LPDB

Supply , installation, testing commissioning of 4Way TPN DB With 40 Amp 4Pole MCB as incomer andSP Mcbs 12 nos For outgoing.6 to 32 amps Main LPDB

Supply , installation, testing commissioning of 6Way VTPN DB With 63 Amp 4Pole MCB as incomer and SP Mcbs 18 nos For outgoing.6 to 32 amps Main LPDB

Supply,Installation, Testing & commissioning of 0.5 mm size tinned copper conductor , 2 pair PVC insulated telephone wire of approve make in existing MS conduits.

Supply,Installation, Testing & commissioning of Telephone outlet box with top plate

Supply,Installation, Testing & commissioning of crone type tag block for termination of telephone cables/conduits in MS sheet steel enclosures as per drawing and specifications.

Tag block 20pair.

Supply , installation,testing and commissioning of enhanced CAT E6 LAN cable in preveiously laid conduits .Data cable installation shall be carried out by approved vendor & final certification shall be required.

Supply , installation,testing and commissioning of RJ 45 connector type computer socket outlet with RJ 45 connector of approved make .

Supply, installation, testing and commissioning of RG 6 Coaxial cable .

Installation, Testing & commissioning of TVoutlet box with top plate

Supply, installation, testing and commissioning of 1.5 SQ MM X 2CORE speaker wires

Supply, installation, testing and commissioning of HDMI CABLE 15 MTR

Supply, installation, testing and commissioning of HDMI CABLE 30 MTR

Supplying, providing wiring (supply, fixing, testing and comm.etc) for Light / Power with following PVC insulated copper conductor single core multi stranded wire ( HRFR ) in existing conduit i/c electrical connections and making good all the damages, painting, cleaning the site etc complete as required as per site requirement and as directed. 3x 4.0 sqmm.

Supply,Installation of 24 watt LED recess / surface fixture 600 x 600 panel , Make of LED OSRAM/ Phillips/Dominent/wipro . Panels should be made of white powder coated CRCA sheet hsg.Lamp type Clear / Neutral White LED,Power Consumption - 32 to 38 W,Wattage of single LED – 0.15 to 0.25 W,No. of LED – depending upon total power consumption and illuminance,Lamp Colour Temp - 4000 to 6000K, Light coverage -- 100° to 120°,Illuminance -- 300 - 450 Lux, Rated lamp life --Min. 50,000 Hrs ,Visor -Acrylic / Prismatic sheet

Supply,Installation of 11 watt LED recess / surface fixture, Make of LED OSRAM/ Phillips/Dominent/wipro .,Life Of LED 50000 Hrs ,Warranty 3 Years , 4 THD % < 10% , Power Factor 0.95-0.99 , Make of Driver C&S/ Olieve / Bajaj wipro , philips crompton ,Operating Current AC 300-350 mA , Operating Voltage AC 100- 240 V , Material of Heat sink Aluminium

Supplying, unloading, storing , laying, testing and commissioning of following sizes of PVC / XLPE insulated (Heavy duty) Al / Cu conductor armoured cables suitable for working voltage upto and including 1100 Volts , laid and tied on existing overhead cable trays; or laid and tied over MS supports in masonry trenches including providing MS supports and clamps for fixing to supports ; or buried in ground complete as required and as per specifications. 4.0 core,10sq mm al cable.

Supply, Installation, Testing and commissioning of the surface / recess mounting following ways MCB DB's 230 / 415 Volts on surface / recessed, complete with tinned copper busbar, neutral bar, earth bar, din bar detachable gland plate, interconnection and making good all the damages, painting, cleaning the site etc complete as required as per site requirement and as directed. (9.27.3) U.P.S. POWER DIS.BOARD :1 no.SPN MCB DB 8 way ( 2 + 6 ways ) , 1 no SPN MCB 16 amp.6 nos SP MCB 10 amp.

Supply,fixing,testing and commissioning of 1 No 6 A Multi Socket with 1No. 6 A switch ( Modular type ) with cover plate , sheet steel box / PVC modular box etc on surface / concealed manner I/c electrical connections and making good all the damages, painting, cleaning the site etc complete as required as per site requirement and as directed

Providing and laying vitrified floor tiles in different sizes with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 sand) including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 1000x1000x 10-12 mm

Stage Table Overall Size:- Length:1200mm, Width: 600mm, Height: 750mm, Top made of 25mm thick Pre-laminated Particle Board. PVC edge beading of 2 mm edges by Through Feed Machine. Provision of Cable manager as per L.H. or R.H. side requirement. Cable duct made of 0.8 mm CRCA Sheet. Leg/Side made of 25 mm thick PLPB fitted with Aluminium section of size 60X40 with grooving. Leg/Side Base & Top plate with profile cut made of M.S. plate 44 mm width & 4 mm thk with knock down fitting arrangement. All steel components are epoxy powder coated after seven tanks anti corrosion treatment of surface.

Chair Stage Low backSize: Total Height-810-895mm, Depth 685mm, Width-555mm Seat Height:425-510mm. 5-Prong nylon base for stability. Twin Wheel heavy Duty Castor for easy mobility under load. Hot pressed ply wood with steel T-Nuts for rigid fastening. Seat and back are covered with PP cover. Sturdy steel column gas lift for centre support and seat height adjustment. Telescopic ABS cover over steel column. Lockable centre tilt mechanism and with Single piece integral skin PU arm rest. Quality tapestry. High density Moulded PU cushion. Upholstery 1.2 Mtr. Over all appearance of product as shown in picture.

Student desk Front Row - Only Desk Front Row Overall Size :- W480mm, D405mm, H770mm, Top- H750mm. Tablet size :- W430mm, D315mm, 12mm thick, Front mould size : Height 467mm, Width 478mm, 12mm thick,:- Mounted on 64mmx64mmx3mm aluminium glide fitted with MS cold rolled close annealed leg made of 60mmx60mmx2mm MS tube and MS sheet 3mm thick covered with nylon cap. Front of desk made of hot pressed ply with 0.6mm thk Laminates. Tablet made of 12mm thick postform on MDF board with 0.6mm thk Laminates. Sliding & foldable in specially designed nylon mould accessories fitted on top aluminium glide of 30mmx70mm. All steel components are powder coated while aluminium glides are anodized or powder coated. Note: Floor must be minimum 100mm thick RCC slab to grout the desk or otherwise written confirmation on deviation should be taken by Bonton, as regard to floor. Steps depth must be as per layout – deviations must be discussed with Bonton and written consent of Bonton is must in this regard before placing the order.

Student desk with chair Middle Row - Desk with BenchMiddle Row Overall Size :- Width 480mm, Depth 800mm, Height 770mm, Top- H750mm. Tablet size :- Width 430mm, Depth 315mm, 12mm thick, Seat size :- Width 477mm, Depth 377mm, 12mm thick, Back mould size : Height 467mm, Width 478mm, 12mm thick, Mounted on 64mmx64mmx3mm aluminium glide fitted with MS cold rolled close annealed leg made of 60mmx60mmx2mm MS tube and MS sheet 3mm thick covered with nylon cap. Front of desk & back of chair made of 12mm thick hot pressed ply with 0.6mm thk Laminates. Foldable seat made of 12mm thick hot pressed ply with 0.6mm thk Laminates. Tablet made of 12mm thick postform on MDF board with 0.6mm thk Laminates. Sliding & foldable in specially designed nylon mould accessories fitted on top aluminium glide of 30mmx70mm.All steel components are powder coated while aluminium glides are anodized or powder coated. Note: Floor must be minimum 100mm thick RCC slab to grout the chairs or otherwise written confirmation on deviation should be taken by Bonton, as regard to floor. Steps depth must be as per layout – deviations must be discussed with Bonton and written consent of Bonton is must in this regard before placing the order.

Student chair Back Row- Only BenchBack Row Overall Size :- Width 480mm, Depth 580mm, Seat Size : Width 477mm, Depth 377mm, 12mm thick, Seat Height 460mm. Back mould size : Height 467mm, Width 478mm, 12mm thick, Mounted on 64mmx64mmx3mm aluminium glide fitted with MS cold rolled close annealed leg made of 60mmx60mmx2mm MS tube and MS sheet 3mm thick covered with nylon cap. Back of chair made of 12mm thick hot pressed ply with 0.6mm thk Laminates. Foldable seat made of 12mm thick hot pressed ply with 0.6mm thk Laminates. . All steel components are powder coated while aluminium glides are anodized or powder coated. Note: Floor must be minimum 100mm thick RCC slab to grout the chairs or otherwise written confirmation on deviation should be taken by Bonton, as regard to floor. Steps depth must be as per layout – deviations must be discussed with Bonton and written consent of Bonton is must in this regard before placing the order.

Sofa 3 Seater Specification- Size-H-700 mm, L-1730 mm, D-800 mm. Structure made of treated agro wood, fitted with 50mm wide rubberized belts 50mm wide with high density PU foam as per design, Upholstered with premium quality PU cloth with help of stitching, where ever necessary.

Conference Table 17 Seater without Chair Size:- Length: 6000mm, Width: 2100mm, Height: 750mm, Top made of 25mm thick Postform Board. Leg made of 25 mm thick & Modesty panel made of 18 mm thick Prelaminated Particle Board. Edge beading of edges by Through Feed Machine.

Chair Conference HI-backSize: Total Height-1070-1190mm, Depth 685mm, Width-590mm Seat Height:425-510mm. 5-Prong nylon base for stability. Twin Wheel heavy Duty Castor for easy mobility under load. Hot pressed ply wood with steel T-Nuts for rigid fastening. Seat and back are covered with PP cover. Sturdy steel column gas lift for centre support and seat height adjustment. Telescopic ABS cover over steel column. Lockable centre tilt mechanism and with Single piece integral skin PU arm rest. Quality tapestry. High density Moulded PU cushion. Upholstery 1.5 Mtr.

Chair conference VisitorSize: Total Height-840mm, Depth 600mm, Width-575mm Seat Height:450mm. Under Structure cantilever type MS cold rolled close annealed Tube 1.6 mm thick. Hot pressed ply wood with steel T-Nuts for rigid fastening. Single piece integral skin PU arm rest. Quality tapestry. Seat and back covered with PP covers. High density PU moulded cushion. All steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface. Upholstery 1.2 Mtr

METHODEX SYSTEMS PVT LTD