COMPREHENSIVE MAINT IN OTM MD ACCN UNDER AGE BR II OF GE SOUTH MAMUN

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 18 mm thick green marble (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills, cooking platforms & like including pointing in white cement (1:2) using marble dust with admixture of pigment to match shade of granite laid over and including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4, complete all as specified and directed.

M&L for non-skid ceramic jointless coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm in floor etc set & jointed in neat cement slurry & pointed in white or coloured cement mixed with pigment to match, laid over and including 15mm thick screed layer in cement mortar 1:6, complete all as specified and directed.

M&L for non-skid ceramic jointless coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match, laid over and including 15mm thick cement screed in cement mortar 1:6, complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 450mmx350mm, thickness 7mm as in vertical surfaces such as skirting, dado, etc., set and jointed in neat cement slurry and pointed with coloured cement to match, laid over and including 10mm thick rendering in cement mortar 1:4, complete all as specified & directed.

Demolition of cement concrete (unreinforced) in ground floor n. exc. 15 cm below or above ground level complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) in sub base of floors surface finished even & rough to receive floor top finish, complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in coping, bed plates benching, floor by maintaining required gradient / undulation etc slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L in repair for Machine pressed precast coloured chequered cement concrete tiles of size 20cm x 20cm x 25mm thick, set, jointed & pointed in neat cement slurry with grey pigment cement and pigments to match as in floors, laid over and including 15mm thick screed bed or bedding layers in CM 1:6, complete all as specified and directed.

M&L for 40 mm thick (average thickness) PCC 1:2:4, type B-1 (using 20mm graded stone aggregates) as in floor finishing to required gradient/undulation, finished even and smooth , complete all as specified and directed.

M&L in repairs for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in surface channels & drains by maintaining required gradient / undulation etc including demolition of existing PCC, complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tanks three layers of 500 ltrs capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed refixing of inlet, outlet & over flow pipe etc. (Minimum weight of 20mm ball valve - 210 gms including dismantling of old existing broken water tank complete all as specified and as directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) area not exc. 1.5 Sqm each, complete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) area exc. 1.5 Sqm but n exc 4.0 sqm each, complete all as specified and directed.

Taking down shutters of any description area exc. 1 sqm and not exc. 2 Sqm each, complete all as specified & directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ windows/ Ceosetory windows & other frames / Chowkhat of size 45 x 70 mm comprising of virgin PVC Polymer of K value 58-60 (Suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ weat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solveng cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/ cum, screw withdrawal strength of 2200N (Face), 1100 N (Edge), minimum compressive strength 58 N/ mm Sq, Modulus of elasticity 900 N/mm Sq and resistence to spread of flame of Class A category with property of being termite / borer proof, water/ moisture proof and fire retardant and fixed in position MS hold fasts/ lugs/ SS dash fasteners of required dia and length complete, as per direction of Engr-in-Charge (Note MS hold fasts/ Lugs or SS Fasteners shall be paid separately) Note: for WPC Solid door/ window frames minus 5mm tolerance in demension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ windows/ Ceosetory windows & other frames / Chowkhat of size 50 x 125 mm comprising of virgin PVC Polymer of K value 58-60 (Suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ weat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solveng cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/ cum, screw withdrawal strength of 2200N (Face), 1100 N (Edge), minimum compressive strength 58 N/ mm Sq, Modulus of elasticity 900 N/ mm Sq and resistence to spread of flame of Class A category with property of being termite / borer proof, water/ moisture proof and fire retardant and fixed in position MS hold fasts/ lugs/ SS dash fasteners of required dia and length complete, as per direction of Engr-in-Charge (Note MS hold fasts/ Lugs or SS Fasteners shall be paid separately) Note : for WPC Solid door/ window frames minus 5mm tolerance in demension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F 35 mm thick factory made wire guazed and skeleton shutters (2nd class hardwood), open rebated and prepared to receive wire cloth, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing wire cloth, etc.; sizes of me-mbers of shutters as specified fitted to chowkats including preparation of surfaces of shutters and application of two coats of synthetic enamel paint over a coat of pink primer, etc complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative both sides Flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ weat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650kg/ cum and screw withdrawal strength of 1800 N (face) & 900 N (Edge), minimum compressive strength 50 N/ mm Sq, Modulus of elasticity 850 N/ mm Sq and resistence to spread of flame of Class A category with property of being termite / borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws, all as per direction of Engr-in-Charge. Note Stainless steel butt hinges and necessary SS screws shall be paid separately.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative decorative both sides Flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ weat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650kg/ cum and screw withdrawal strength of 1800 N (face) & 900 N (Edge), minimum compressive strength 50 N/ mm Sq, Modulus of elasticity 850 N/ mm Sq and resistence to spread of flame of Class A category with property of being termite / borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws, all as per direction of Engr-in-Charge. Note: Stainless steel butt hinges and necessary SS screws shall be paid separately.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F for 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F in repair 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 250 mm long aluminium alloy , anodised sliding door bolt with hasp, staple bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F in repairs 250 mm long aluminium alloy , anodised sliding door bolt with hasp, staple bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S & F in repair 100 mm long Butt hinges type C-21, extruded aluminium alloy with galvanised mild steel hinge pin, anodised complete all as specified and directed.

S&F 150 mm long aluminium handle cast type anodised complete all as specified and directed.

S&F in repairs 150 mm long aluminium handle cast type anodised complete all as specified and directed.

Hacking out old broken glass ( any thickness , size, quality, or description) from metal frame glazed with putty or fixed with beads/ clips complete all as specified and directed.

S&F 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F 3mm thick Figured glass, pinhead type in squares n exc 0.5 sq. m each pane fixed with oil putty complete all as specified and directed.

S & F GI wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or rubber/aluminium beads complete all as specified and directed.

S&F in repairs GI wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or rubber/aluminium beads complete all as specified and directed.

S&F 300mm size mild steel, ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F in repair 300mm size mild steel, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L for preparation of old painted surface of steel of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint, white or tinted complete all as specified and directed.

M&L for preparation of old painted surface of wood or wood articles of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint, white or tinted complete all as specified and directed.

S&F in repair 25mm PVC Ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F in repair 20mm PVC Ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F in repair for 15mm bore water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

S&F in repair for 20mm bore water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

S&F in repair for Shower rose swivel type brass chromium plated any size including fixing to steel pipe or unions complete all as specified and as directed.

S&F in repair Stop valve/Angle valve (ISI Marked), fancy type cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore ccomplete all as specified and as directed.

S&F in repair stop valve (ISI Marked) 15 mm bore fancy type, chromium plated with long shank and cup (concealed type), cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore complete all as specified and as directed.

S&F in repairs 15mm bore bib tap, with flange, cast copper alloy fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F in repairs 15mm bore PTMT bib tap, any colour, high pressure screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S & F in repair Flush pipe (PVC) squatt pattern closet including all joints and making good to the floor complete all as specified and directed.

S&F in repairs vitreous china wash hand basin flat back or angle back type, white of bowl size 550mm x 400mm including CP brass waste coupling and rubber plug, porcelain stopper, a pair of CI brackets, waste pipe of 32mm dia, complete all as specified and directed.

S&F in repairs 15mm bore Pillar tap, cast copper alloy, fancy type, with capston head, chromium plated, screwed down, high pressure with long screwed shank and fly nuts, screwed for iron pipe, complete all as specified and directed.

S&F in repairs Brass CP towel rail 20mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

S&F in repairs Vitreous china squatting pan of 'Orissa pattern' of size 580mm x 440mm, white with CI ‘P’ or ‘S’ trap, front or back inlet and foot rests of any pattern (including fixing of flush pipe) and connecting etc. including provision of cement concrete bedding, complete all as specified and directed.

S&F in repairs Vitreous china wash down water closet pan (pedestal pattern), white complete including fixing to trap including PVC seat and cover with hinging device for pedestal pan and connecting etc, complete all as specified and directed.

S&F in repairs PVC low level flushing cistern, valveless, syphonic action type, 10 litres capacity with inlet ball valve and handle with and including brackets and PVC bend pipe 60/90cm long etc, complete all as specified and directed.

S&F PVC (SWR) floor trap, plain with grating of 75/100mm dia including jointing with solvent cement complete all as specified and directed.

S&F in repair 110 mm dia PVC (SWR) rainwater pipes single socketed, in any length with rubber ring joints,fixing to walls complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) rainwater pipes single socketed, in any length with rubber ring joints,fixing to walls complete all as specified and directed.

S&F in repair PVC 110 mm bends /TEE complete all as specified and directed.

S&F in repair PVC 75 mm bends /TEE complete all as specified and directed.

S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays,including bolts and nuts and securing ends of stays to wall or roof for 100 mm dia CI pipe complete all as specified and directed.

S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays,including bolts and nuts and securing ends of stays to wall or roof for 75 mm dia CI pipe complete all as specified and directed.

S&F GI pipe 25mm dia light grade (in short length) as spout pipe in sunken floor slab laid in slope to brick wall with PCC (1:2:4) type B-1, complete all as specified.

Material and labour for Rendering 15mm thick cement plaster on brick work or concrete surfaces in cement mortar (1:4) including using WPC liquid as per manufacturer instruction @ 200ml /50 kg of cement to sunken portion with proper slope towards outside and finishing cement concerete or brick work surface even and smooth using extra cement including application of APP based polymeric membrane minimum weighing 3Kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid over primed surface by forced application complete all as specified and as directed by Engr-in-Charge Note: Water proofing compound shall be measured and paid for separately under respctive item.

M & L for Accessible, Sloped & Exposed Terrace, Deck Slab as under:- (a) Removal of Existing PCC/Brick Bat Coba/Mud phuska/ APP membrane from the roof stacking the reusable material and disposal of unserviceable ribbish out site the campus as per direction of the client with in 3 Km. (b) Cleaning of surface of loose dust and dirt cement slury etc. by means of wire brush, dust removing brush and scraper etc.In case of Pot Holes/ Cracks same shall be repaired with cement with cement admixed with Polymer as per manufacturer instructions etc. (c) Gola on Mother Slab: Providing and Making of PCC coving (gola) of size 75mm X 75mm with concrete Mix (1:2:40, cement sand, grit and including cost of mixing water proofing compund of approved make etc. complete as per direction by engineer in charge. (d) The surface shall be primer with Smart care epoxy primer to seal the pores and enhance the adhesion of the coating. Supplying and applying single component water proofing liquid membrane based on pure elastomeric, polyutherine resin smart care pu magnum us, cold applied of spray/ brush applied, membrane with elogation > 600% and tensile strength of 3-4 Mpa as per Astm D 412. crack bridging ability of 3mm as per ASTM C1305, no leakage upto 5 bars of water pressure as per DIN 1048, shore A Hardness > 50 Shore as per ASTM D 2240. The minimum thickness to be applied shall be 1.5mm. (e) Providing & laying of protective Geotextile fabric 150GSM over the entire membrane with proper overlaps of 75mm before of Brick bat coba treatment. (f) M & L for Non skid ceramic jointless coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but nexc 0.18 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 20mm thick screed layer in cement mortar 1:6, complete all as specified and directed .

Supply and applying for two component elastomeric acrylic polymer modified cementitious waterproofing coating over brick wall surface, Smartcare UltraBlock 2K or approved Equivalent Having>220% elongation as per ASTMD 2370, Resisting 5 Bars Hydrostatic pressure as pepr DiN 1048, Reduction to rapid chloride shall be 70 as per DIN 1048, Craki bringing upto 3.50mm as per EN 1062. The coating shall have food grade certificate from laboratories like CFTRI. The Mixing ratio of Coating shall be 2 Parts of Powder & 1 Part of Liquid without any water addition in mixing etc. complete as per manufacturers specification. Minimum consumption shall be 2 kg/Sqm. Supply and applying bond application MIX AP SC repair polymer and cement in Ratio of 1: Brush apply 1 or 2 continuous coat of Mix and ensure minimum consumption shall be 0.2 Kg/Sqm complete all as specified and directed.

M& L preperation of inaccessible roof surface by scrapping and properly cleaning the existing roof treatment in any number of layers upto original RCC roof top surafce. (i) Apply first coat Fiber reinforced Elastomeric liquid water proofing membrane formulated with PU hybrid polymers and reinforcing acrylic fibres with sun reflective index(SRI) of 100-110, having minimum elongation of 350% tensile strength of 2.9 Mpa and shall have cracks bridging ability upto 2.5mm and shall resisit 10 bars of hydrostatic pressure reduce surface temperatureuoto 10 degree celsius with 33% dilution of priming coat. (ii) Laying of fiber mesh of 0.3 mm thickness weave in leno pattern having 45 gsm/Sqm and pasting it properly with overlap of 50mm and allow it to dry. (iii) Apply second coat of undiluted coat @4.5 Ltr/Sqm. Apply third and final co for 10mm thick cement rendering in CM 1:E168 at undiluted @0.45 ltr/sqm. (iv) Apply third and final coat [email protected]/Sqm as directed by Engr in Charge. (a) M&L for 10mm thick cement rendering in CM1:3 and finishing the surface even and smooth before application of priming coat complete all as specified and directed

M&L for cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in slabs supported on walls, sunken floor, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs including demolition of existing concrete etc complete all as specified and directed

S&F in repairs sheet glass shelf assembly, consisting of 5.5 mm thick sheet glass 12 cm wide with CP brass bracket, complete all as specified and directed.

M&L for PCC 1:2:4 type B1 using 20 mm graded crushed stone aggregate as in landings, cover slabs (for drains), shelves, chajja & similar works with plan faces & set in cement mortar 1:4 incl demolition of existing PCC complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over in reinforcement cut to length, bent to shape required incl bending spirally cranking, hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified.

S&F in repairs PVC connection 15 mm bore with PTMT nuts of length 450 mm long complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate as in plinth protection finished even and smooth using extra cement (incl necessary joint filling with mixture of paving bitumen & sand in 1:3) complete all as specified and directed.

S&F in repair box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick M S sheet tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire cloth and glass panes only shall be measured and paid seperately) with side hung shutters with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100 mm long for each leaf and 10 mm square bar grills at spacing as shown on drg welded to FI frame work, including other fittings, hinges, handles, tarred hold fasts, PCC blocks etc all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 complete all as specified and directed.

S&F in repairs 20mm bore stainless steel drapery rod with 1.0mm thick PVC wood grain coating including brackets and knobs, fixed on windows and doors for hanging curtains, complete all as specified and directed.

S&F in repairs syphonic action kit for 10 litres capacity PVC flushing cistern, complete all as specified and directed.

S&F in repairs Jet Spray (with 1.50 Mtr tube), fixed to EWC and angular stop cock/valve, complete all as specified and directed.

S&F in repairs 32/40mm CP waste coupling for sink complete all as per specified and directed.

S&F factory made 18mm (+0.7mm) thick WPC cupboard shutter/ kitchen cabinet, prelaminated one side with coating of ultra voilet chemical, glossy/mat finish incl. 100% termite/water proof, fire retardant, Eco friendly, density not less than 600Kg/cum finish at all edges for making edges lipping/bending, complete as per direction of Engineer-in-Charge and manufacturer's specifications.

S&F 30 mm flap Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F in repair 100 mm Hasp and staple,aluminium anodised, including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F in repairs high grade stainless steel kitchen plate rack of size 700 x 900 mm of approved make fixed with mild steel screw complete all as specified and directed.

S&F in repairs 32/40 mm dia, corrugated waste pipe suitable for WHBs/sinks including threaded PVC socket suitable for shank of waste coupling complete all as specified and directed.

S&F in repairs 32/40mm PTMT waste coupling for basin/sink (half or full threaded) complete all as per specified and directed.

S&F ball catcher with proper magnetic effect fixed with shutter, complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls of any description by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and including taking down existing grass, vegetation, small trees, making good the disturbed surfaces to match and applying one coat of cement base paint including curing before and after providing cement base paint complete all as specified

M&L for preparation of old decorated surfaces of walls of any description and applying one coat of oil bound distemper, white or tinted, including removing nails etc and making good the disturbed surface complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls of any description by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coats of white wash complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling of any description by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash complete all as specified and directed.

Taking down cement plaster / wall tiles including backing etc from brick/stone walls / concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 over on brick work and concrete surfaces of wall, finished the surface even and smooth without using extra cement, including necessary scaffolding complete all as specified and directed.

M/L 15 mm thick rendering in two layers (5 mm thick in CM 1:4 over 10 mm thick in cement mortar 1:6) mixing with liquid WPC @ 200 ml/ 50Kg of cement on brick or concrete surfaces and finished even and smooth without using extra cement including necessary scaffolding all as specified and directed Note: Water proofing compound shall be measured and paid for separately under respctive item.

M&L for rendering 10 mm thick plaster on fair face of brick work or concrete surface as in ceiling in cement mortar 1:3, finished even and smooth without using extra cement, including necessary scaffolding complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls by applying 1mm thick wall care putty making the surface even & smooth and applying two coats of oil bound distemper, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resisant priming paint, white or tinted, including curing before and after paint complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls, roof projection, ceiling, chajjas and applying three coats of white wash, complete all as specified and directed.

S & F in repair Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.Fe 410 -W (Gde-E- 250) quality- A complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified including dismanling of existing roof sheets any type all as specified.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick and 600 mm width of an ecofriendly colour having tensile strength of 550 Mpa as in riges/vally, fixed with self tapping screws any type complete all as specified and directed.

M&L for brickwork with Fly Ash Bricks (old size), straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6, including demolition of existing brick work, complete all as specified and directed.

Please Enable Macros to View BoQ information