SPECIAL REPAIR TO ROOF SHEET OF BLDG NO WB-12 AND WB-13 UNDER GE (MCTE) MHOW

Amount

Dismantling unframed timber scantlings 40 sq. cm & over in section, in any position complete all as specified

Dismantling unframed timber fillets, rails, posts, rafters,purlins, etc. under 40 sq. cm in section, in any position complete all as specified

S&F 0.50mm thick galvalume sheet profile pattern precoated coloured having tensile strength 550 Mpa as in roof covering, fixed with self driving screws, including dismantling of Mangalore pattern or similar tiles in roofing Roof covering or Plain or Corrugated steel sheeting any gauge, thickness complete all as specified

S&F 0.50mm thick galvalume sheet precoated coloured Profile ridge, fixed with self driving screws, including dismantling of plain or corrugated steel sheeting ridge any gauge thickness or old manglore patteren ridge complete all as specified

S&F of structural steel work as in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified

M&L for rolled section/ hollow tube section as in post, main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecction plates including drilling hole for bolting, connecting to gusset plate etc complete all as specified

S&F of structural steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats complete all as specified

S&F MS plates (plain or chequered) channels square cut to or notched forming holes with riveted bolted or welded attachment for Fe-410W complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal/ square heads at one end & screwed the other/ screwed both ends, each screwed end to be fitted with washers & one hexagonal or square nut, length of bolt exc 22.5cm & n exc 30cm long dia of shank 16 to 20mm, complete all as specified

M&L for Cutting channels, grooves or rebates n exc 15cm girth, and trimming surface with or without reinforcement complete all as specified

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enameled paint over a coat of red oxide all complete all as specified

Demolition of brick work built in cement mortar in any position and removing rubbish off the premises within 50m complete all as specified

M&L for brick work in modular size with sub class "B" bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L for cement concrete type B-1, 1:2:4 mix (using 20mm graded stone aggregate) in bed blocks, coping etc; including necessary formwork complete all as specified

Taking down cement or cement lime plaster of any description including racking out joints, hacking for keys, scrubbing down with water etc, complete all as specified

M & L for rendering 15mm thick on fair faces of brick work or concrete surface in CM 1:4 surface finished even and smooth without using extra cement, complete all as specified

M&L for preparation of new surfaces of walls and applying two coat of weather proof coat over a coat of primer complete all as specified

M&L for preparation of old surfaces of walls and applying two coat of weather proof coat complete all as specified

M&L for Rendering 15mm thick on fair faces of concrete/ brick interior surfaces in cement mortar 1:6 as per manufacturer's instruction, finished fair and even without using extra cement complete all as specified and directed.

M & L for prepration of new wall surfaces & applying birla/ J.K. wall care white putty 2mm thick for levelling the surfaces and applying two coat of interior emulsion distemper over a coat of wall primer incl. preparation of surfaces of walls etc complete.

M&L for complete removal of existing treatment from walls by scrapping & washing etc and applying Birla/ J.K. wall care white putty 2mm thick for levelling the surfaces including properly making of 'V' shape crakes and filling of all crakes with crakes seal of walls and applying two coats of oil emulsion distemper over a coat of primer complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint on wooden surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of old painted surface complete all as specified

M&L for applying one coat of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of old painted surface, complete all as specified

Dismantling/ wall and ceiling boards (fibre pulp, insulation etc) or insulation boards/ slabs, complete all as specified

M&L for suspended false ceilling comprising of 4mm thick non asbestos fibre cement bulding boards of size 595mm x 595mm ‘E’ Board Classic Design Lake & hill including supply and fixing GI ‘Tee” grid frame work made of special section of M.S galvanized sheet 0.30mm thick, bottom portion painted with cellular nitro painting, warping the suspending wire around the existing wooden/ steel purlin/ rafter for suspending grid frame work of size 605mm x 605mm suspended with 4mm dia GI wire @ 1200mm c/c on main Tee and fixed to T-grid with the help of level clip or as per manufacturer direction. The section consisting of main Tee 37mm x 24mm x 0.60mm, cross runner tee 37mm x 24mm x 0.60mm and perimeter angle of 24mm x 24mm x 0.50mm thick. Perimeter angle to be fixed to wall with GI screw of 40mm long @ 450mm c/c along the perimeter of wall including applying two coats of distemper oil emulsion complete all as specified and directed

M&L for 10-12mm thick decorative plaster of paris false ceiling bending/ moulding as required shape with two coats of plaster emulsion paint over a coat of primer on decoratived surfaces of ceiling including 26 gauge galvanished iron sheet 'C' shaped main member @ 750mm C/C cross member 'U' shape @ 450mm c/c and perimeter of 'C' shaped GI wire 6mm dia or more or FI 40 x 4mm thick for hanging arrangement with MS suspension fastner spaced @ 450mm C/C in both direction and 'C' member shall be made out of not less than 90mm wide GI sheet strip and side tray as required of approximate size 3.5 mtr height as required at site complete all as specified and directed.

Taking down carefully copper/ alluminium point wiring (light, fan, sockets or power) complete including all fitings and fixtures such as switches, sockets, ceiling roses, pendents, regulators, light fittings etc, removing matrials to store for taking credit and making good disturbed surfaces complete all as specified.

Taking down carefully copper/ aluminium sub-main wiring any type and making good the disturbed surface of walls and floors etc complete all as specified.

Taking down existing ceiling fans and exhaust fan of any size and re-fixing the same after B/R work including overhauling/ servicing, winding of fan, replacement of defective parts, painting of the complete fan with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and writing MES Number in black paint with skilled painter and providing three core flexible copper cable for connection from ceiling rose/ connector complete all as specified.

Taking down carefully TPN DB/ SPN DBs/ sheet metal earth plug socket any size and any type including MCBs any type and making good the disturbed surface of walls and floors complete all as specified.

Taking down carefully light fitting any type for refixing or taken in schedule of credit complete all as specified.

M&L for Point wiring with 1.5 Sqmm (nominal cross sectional area), single core, PVC insulated with multistranded PVC unsheathed FRLSH copper conductor cable in and including rigid non- metallic PVC concealed conduit of suitable size medium grade ISI marked complete, including one continuity earth wire of PVC insulated, unsheathed 1.5 Sqmm (nominal cross sectional area) FRLSH copper conductor connected to all fittings, common earth and connected to earth dolly including modular flush box with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches and blank plates of suitable size all fittings and accessories and making good disturbed surface of walls and floors etc. complete all as specified and directed for the following:- Note:- Make of modular GI box should be same with switch/ socket.

One light/ fan/ bell controlled by one, one way switch 5/6 Amps complete all as specified.

One 3 pin, 5/6 Amps socket outlet point on independent board controlled by one, one way 5/6 Amps switch complete all as specified.

One 3 pin, 5/6 Amps socket outlet point on SAME BOARD controlled by one, one way 5/6 amps switch complete all as specified

M&L for Point wiring with 1.5 Sqmm (nominal cross sectional area), single core, PVC insulated with multistranded PVC unsheathed FR LSH copper conductor cable in and including rigid non- metallic PVC surface casing caping/ conduit of suitable size medium grade ISI marked complete, including one continuity earth wire of PVC insulated, unsheathed 1.5 Sqmm (nominal cross sectional area) FRLSH copper conductor connected to all fittings, common earth and connected to earth dolly including modular metal flush box/ PVC, covered with modular white cover plate with inner frame suitable for modular switches and blank plates of suitable size all fittings and accessories and making good disturbed surface of walls and floors etc. complete all as specified and directed for the following:- Note:- Make of modular GI box should be same with switch/socket and type of wiring will be executed as per site requirement and direction of Engr-in-Charge.

One light/ fan/ bell controlled by one, one way switch 5/6 Amps complete all as specified

One 3 pin, 5/6 Amps socket outlet point on independent board controlled by one, one way 5/6 Amps switch complete all as specified

One 3 pin, 5/6 Amps socket outlet point on SAME BOARD controlled by one, one way 5/6 Amps switch complete all as specified

M&L for Point wiring with 2.5 Sqmm (nominal cross sectional area), single core, PVC insulated with multistranded PVC unsheathed FRLSH copper conductor cable in and including rigid non- metallic PVC concealed conduit of suitable size medium grade ISI marked complete including one continuity earth wire of PVC insulated, unsheathed 2.5 Sqmm (nominal cross sectional area) FRLSH copper conductor connected to all fittings, common earth and connected to earth dolly for one three pin 15/16 Amps socket out-let point on an independent board including modular metal flush box/ PVC, covered with modular white cover plate with inner frame suitable for modular switches and blank plates of suitable size incl complete all as specified and directed Note:- Make of modular GI box should be same with switch/socket and type of wiring will be executed as per direction of Engr-in-Charge.

S&F of Ceiling rose three terminals surface bakelite type, AC, 50 HZ, 230V, complete all as specified.

S&F modular switch 1 way 6 A, 1 module complete all as specified.

S&F modular socket 6 Amps 2/3 pin combined 2 module complete all as specified.

S&F switch modular type 16 A, 1 module complete all as specified.

S&F Socket modular type multipurposes 6/16 A, 2 module complete all as specified.

All as per No. 34 here in before but using 4.0 Sqmm single core copper conductor FRLSH cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 Amps switch socket cobmination point including necessary running of 4.0 Sqmm PVC insulated copper conductor FRLSH cable as earth continuity conductor along with wiring and connecting to the common eath dolly. (for AC Point)

S&F Inverter LED batten 20 watt with squre profile and polycarbonate channel. Lithium lon battery with charging time 8 hourse -10 hourse and back up time upto 4-10 hours. with extruded environmental friendly, energy efficient with three core flexible copper conductor cable of suitable size from ceiling rose complete with all connected accessories complete all as specified.

S & F for Energy saving new generation environmental friendly long life versatile LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including necessary mounting arrangements and provision of 2.5 Sqmm three core copper conductor cable multi stranded from ceiling rose to light fitting and necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts, complete all as specified.

S & F LED down light luminaire round Surface/ Recessed Mounted 18/20 watts, white finish operating voltage 150 Volts - 270 Volts AC, 50 Hz, recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling, including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified

S & F LED luminaire 600mm x 600mm square LED panel 35/36 watts, 220 volts, lumen efficacy of 120 lumens/ watt, AC Surface/recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling, including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified

S&F Flush mounting factory made Vertical FP DB, IP-43 Protection -IK 09 with metal double door with 200 Amps rated copper busbar with 2 neutral bar, earth bar and cables ties for cable management fully insulated bus bar with set of wires and door earthing with provision of space for 100-125 Amps MCCB as incomer and SPN/TP MCBs as out going, 6 way (Optium F1+18 Module) including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonry etc and making good of disturbed surface to match with existing colour of wall or make suitable arrangement to installed the DB on the wall by drilling screwing complete all as specified

S&F MCB DB SPN 8 way double door with 200 Amps rated bus bar, 230 volts, 50 Hz including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonry etc and making good of disturbed surface to match with existing colour of wall or make suitable arrangement to installed the DB on the wall by drilling screwing complete all as specified

S&F 32 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 32 Amps and current carrying capacity in the MCB DB complete with connection by using alluminium/ copper lugs, testing and commissioning complete all as specified.

S&F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp in the MCB DB complete with connection by using alluminium/ copper lugs, testing and commissioning complete all as specified and directed.

S&F MCCB 4 pole, 415 volts, in the existing panel/ location and connection with using aluminum lugs complete all as specified and directed for 100 Amps rating, 36 KA breaking capacity with connection by using alluminium/ copper lugs testing and commissioning complete all as specified and directed.

M&L for single pole and earth encolsure with a two pin and earth plug with socket 240 Volts, 50 Hz complete with one single pole MCB SP 20 Amps including necessary provision for inserting the Metal clad in wall by cutting the brick/ stone masonry etc and making good of disturbed surface to match with existing colour of wall complete all as specified and directed.

M & L sub main wiring with 02 runs of 6 Sqmm main wire along with 01 run of 06 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC concealed/ surface conduit (medium grade) wherever necessary with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the same complete all as specified and directed. Note:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

All as per item No.51 here in above but with 2 runs of 4 Sqmm main wire along with 01 runs of 4 Sqmm earth wire complete all as specified.

S&F in repair of exhaust fan, steel body AC single phase 230 volt of size 380mm sweep complete with blade, frame all as specified and directed including making/ alteration of hole whatever necessary by cutting of wall/ surface and making good disturbed surface, painting to match with existing colour of surfaces complete all as specified and directed.

S&F in reapair of ceiling fans complete with blades, down rods 15mm/12mm upto two mtr, electronic regulator and remote with battery and complete accessories, 230 V, 50Hz, 1200mm sweep and rated power 26W (+ 10%) and rate speed 350 RPM (+ 10%) Min air delivery 210 CFM with service value shall not be less than 8.46 BEE as per BIS. Five star rated with brushless direct current motor (BLDC), painting to match with existing surfaces including writing the MES number with synthetic enamel paint complete all as specified. Note:- Rate of electronic regulator and remote with battery shall be deemed to be included in the quoted rate.

S & F Galvanised, steel rod 16/15mm diameter and length from 0.5 meter to 2.5 metres as per site requirement complete all as specified.

M & L for of earthing complete with galvanized steel earth plate electrode 600 x 600 x 6mm thick, buried directly in ground vertically to a depth not less than 2.25 meters deep below ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level connect to galvanised earth lead wire of 4.0 sqmm size by means of bolts, nuts, check nuts and washers of galvanized iron or steel up to 7.5 meter length including connected to earth plate including necessary excavation & earthwork, PCC (1:3:6) type C-1 earth chamber, 40mm thick RCC cover 1:2:4 mix with 6mm dia nominal reinforcement @ 150mm c/c both ways etc complete all as shown in electrical plate No 5, connected to earthing test point complete including testing on completion all as specified.

BHATIA ASSOCIATES (BID ID -3273087)

sunway associates (BID ID -3273407)

Goyal Construction (BID ID -3273208)

M/S GARG CONSTRUCTION (BID ID -3276546)

r.s.jain & sons (BID ID -3273314)

SATHI ENTERPRISES (BID ID -3272824)

M/S Umashanker Mishra (BID ID -3273303)