ADDN/ALTN AND SPECIAL REPAIR TO 44 DUs IN ARJAN VIHAR AND 20 DUs IN DK PART-I AND DK PART-II UNDER GE (CENTRAL)

Amount

Item No 1 Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) including removal of rubbish out side complex (MOD land) complete all as specified and directed

Item No 2 M & L for 40 mm thick cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in floors surface finished even and smooth using extra cement complete all as specified and directed

Item No 3 Supply only glass dividing strips, 38mm wide and 3mm thick and inserted in position to conform to design, complete all as specified and directed. (Note : - Rate for fixing included in item No 02 above.)

Item No 4 M & L for 75 mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection laid in bays & surfaces finished even and fair complete all as specified and directed

Item No 5 Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) including removal of rubbish outside complex ( MOD land) complete all as specified and directed.

Item No 6 Demolition/cutting of RCC of any description such as RCC Water tank, beams, columns or any position by using diamond saw blade cutting machine without damaging adjacent RCC structures not otherwise specifically provided for (reinforcement cutting as required to facilitate demolition) including G+5 on roof top/Mumty/ parapet and removal of rubbish outside complex (MOD Land) complete all as specified and directed. Note: The rate quoted by the contractor is deemed to include using saw blade cutting machine wherever required as directed by Engineer in Charge. Rate quoted are for G+5 Building

Item No 7 M&L reinforced cement concrete 1:1.5:3 type A-1 (using 20mm graded stone aggregate) (nominal mix) as in slabs supported on wall,landing, balconies, shelves and like including bonding agent , complete all as specified (reinforcement to be measured & paid under respective items).

Item No 8 M&L Formwork to soffits of suspended slabs (rough finish) such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

Item No 9 M&L form work to edges of concrete flats, treads, breaks in floors window cill, concrete railing opening in conc wall , floor and roof n.exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20cm wide for rough finished surfaces of concrete, complete all as specified.

Item No 10 Supply and fix TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) but not less than 0.9 mm dia complete all as specified.

Item No 11 All as per item 10 above but 6mm to 8mm dia

Item No 12 Demolition of brick work built in cement mortar in any description and position, complete all as specified.

Item No 13 M&L for brick work with sub class 'B' brick straight or curved on plan exc 6 metre mean radius with old size bricks, built in cement mortar 1:6, complete all as specified.

Item No 14 M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls with old size bricks, built in cement mortar 1:4, complete all as specified.

Item No 15 All as per item no 13 above but except bricks

Item No 16 M&L for cement concrete 1:2:4 type B1(using 20mm graded stone aggregate) as in blocks for hold fast, coping, benching etc. including weathering, slightly rounded or chamfered angles or throating including form work to concrete surfaces, complete all as specified upto six storey height.

Item No 17 M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1 : 4 mixed with water proofing admixture finished even and smooth without using extra cement complete all as specified. (Water proofing admixture shall be measure and paid separatelly).

Item No 18 M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1 : 4 mixed with water proofing admixture finished even and smooth without using extra cement including taking down old plaster complete all as specified. (Water proofing admixture shall be measure and paid separatelly).

Item No 19 Supply only liquid water proofing admixture of approved quality.

Item No 20 M & L for 10 mm thick rendering in cement mortar 1:3 on concrete surfaces of ceiling, chajja and like surface finished even and smooth without using extra cement and applying 3 coat of white lime wash on newly plastered surfaces of ceiling including taking down old plaster complete all as specified and directed.

Item No 21 All as item No 20 above but two coat of OBD over 1-2 mm thick wall care putty over one coat of acrylic resistant primer

Item No 22 M&L for Preparation of new surfaces (Plastered or un-plastered) on ceiling and applying three coats of white lime wash, complete all as specified.

Item No 23 M&L for preparation of old decorated surface(Plastered or unplastered) of ceiling by brooming down or steel wire brushing scraping down smook root mould moss and efforescent salts and treating oil and greasy spots as applicable and applying two coat of white wash complete all as specified and directed.

Item No 24 M&L complete removal of existing treatment of old surface of ceiling including tucking of surface and grinding the surface with mechnical grinder for preparation of new surface and applying 2mm thick putty POP punning/plaster including two coat of oil bound distemper on ceiling complete all as specified and directed

Item No 25 M & L for 15 mm thick rendering in cement mortar 1:6 on fair face of brick walls/ concrete surfaces & finished even and smooth without using extra cement, including taking down old plaster complete all as specified.

Item No 26 M&L for Preparation of new surfaces (Plastered or un-plastered) of walls and applying three coats of white lime wash complete all as specified.

Item No 27 M&L for Preparation of old decorated surfaces(Plastered or unplastered) of wall including cornices, pillasters etc by complete removal of existing treatment and applying two coats of white lime washing, complete all as specified.

Item No 28 M&L for Preparation of new surfaces (Plastered or un-plastered) of walls and applying two coats of oil bound distemper(white or tinted) over a coat of 2 to 3mm thick chalk whitening wall putty over one coat of alkali resistant primer on plastered surfaces complete all as specified.

Item No 29 M&L for preparation of old decorated surface (plastered or unplastered) of walls by complete removal of existing treatment by mechanical grinder and applying two coat of oil bound distemper over a coat of 2 to 3 mm thick wall putty over one coat of alkali resistant primer on plastered surfaces of walls complete all as specified .

Item No 30 M&L POP cornice 75mm to 100mm thick as per design/moulding as approved by GE/Engr-in-charge in corner of ceiling incl two coats of oil bound distemper complete all as specified and directed.

Item No 31 M&L for complete removal of existing treatment on wall , preparation of surfaces and applying two or more coats of plastic emulsion paint with and including applying cement based wall care putty uniformly 1mm thick (average thickness) upto 1.20m height of wall complete all as specified and directed.

Item No 32 M&L Easing of doors/windows for easy opening /closing ,tightening of hinges and changing its position or adjustment of tower bolts/sliding bolts etc area not exc 2 sqm each complete all as specified and directed.

Item No 33 Taking down chowkats or frames n.exc 1.5 sqm each with shutters (without taking off shutters from frames), complete all as specified.

Item No 34 Taking down chowkats or frames exc. 1.5 Sqm and n.exc 4 Sqm each with shutters (without taking off shutters from frames ), complete all as specified.

Item No 35 Taking down shutter of any description exc 1 sqm and not exc 2 sqm each, complete all as specified.

Item No 36 Taking down shutter of any description exc 1 sqm and not exc 2 sqm each, and refixing in same opening after easing complete all as specified.

Item No 37 M&L for 2nd class hardwood plain, solid straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, complete all as specified.

Item No 38 S& F 35 mm thick flush shutters (factory made) solid core construction, with block board core and plywood face pannel, commercial type on both sides. Flush shutters shall have teak wood edging as specified complete all as specified.

Item No 39 S&F 35mm thick 2nd class Hard wood rail & style (factory made) plain, framed, panelled shutter (two panel) with lock rail & panel of 12mm veneered particle board with commercial veneering on both sides. The size of rail & style as per IS :1003 (Part I), Kiln seasoned & chemicals pressure treated, complete all as specified.

Item No 40 M&L for 35 mm thick 2nd class hard wood glazed and skelton door shutter, factory made, open rebated and prepared to receive glass/guage etc. (without sash bar) edges of frames plain, chamfered or rounded, fitted with cut & mitred beads for securing glass/guage etc size of member as specified in SSR Part I Section 8 clause 8.24(a) and fixed to chowkat, complete all as specified.

Item No 41 M&L for 30 mm thick 2nd class hard wood glazed and skelton window shutter, factory made, open rebated and prepared to receive glass/guage etc. (without sash bar) edges of frames plain, chamfered or rounded, fitted with cut & mitred beads for securing glass/guage etc size of member as specified in SSR Part I Section 8 clause 8.24(b) and fixed to chowkat, complete all as specified.

Item No 42 S&F Factory Made Solid PVC double door frame of size 120 x 50mm with a wall thickness of 5mm (+0.25) made out of extruded 5mm (+0.25) thick prelam PVC sheet of density 600kg/cum manufactured by an ISO-9001-205 certified company ,and by joining 3 Nos. heat moulded PVC section, The Hinge section of size 35 x 35mm shall be made from plain colour PVC sheet of 5mm (+0.25) thickness, the inside section will be covered with 5mm thick PVC sheet C shape covering section of size 120mm x 50mm. At centre top section of 5mm (+0.25) thick 50x50x50mm pattam section should be pasted with solvent cement adhesive to make double pattam of frame. The frame shall be mitre cut at two corners and joined with 4 Nosof 150mm long L brackets of 19mm x 19mm M.S square tube or joint by fusion heat welding. The two vertical doors frames are to be shall be reinforced with 25mm x 25mm M.S. square tube of 19 gauge through out the frame. The door frame shall be fixed to wall using 8/100mm long M.S Screws through the frame by using PVC fasteners. A minimum of 4 nos. of screws to provided for each vertical member & minimum 2 nos. for horizontal member etc complete as per manufacturers specifications and direction of Engr in charge.

Item No 43 S & F Factory Made solid PVC moulded door shutter 35mm thick (styles) with 2, 4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face and 2mm thick prelam PVC sheet on back face complete all as specified and directed

Item No 44 FRP DOOR FRAME WITH DOUBLE REABATE :- M & L Fibre galss reinforced plastic (FRP) door frames shall be three lagged of cross section 120 mm x 65 mm having rebate of 32mm x 15mm to receive shutter of 30 mm thickness. The laminate door frame moulded with fire retardant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fibre glass from all sides. MS stay shall be provided at the bottom to steady the frame etc, complete all as specified and directed.

Item No 45 All as per Item No. 44 above but FRP door frame with single rebate and door frame cross section 90 mm x 45 mm

Item No 46 FRP PANEL DOOR SHUTTER : M & L FRP door shutter shall be 30mm thick glass fibre reinforced plastic (FRP) panelled door shutter of required colour and approved brand and manufactures. Made with fire retardant grade unsaturated polyester resin moulded to 3mm thick FRP laminate for forming holow rails and styles with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP panels and confirming to IS 14856-2000.

Item No 47 PVC WIRE MESH DOOR SHUTTER : Factory made solid PVC wire gauged door shutter 35 mm thick (style) consisting of rame made out of MS tubes for top &bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail&bottom rail on either side and as gap insert for top rail and bottom rail. The wire gauze shall be 0. 36 mm nominal dia of stainless steel wire and average width of aperture 1.40 mm ,the wire gauze shall be wrapped on an additional square 8 mm MS Solid tube and this tube shall be welded to MS Tubes. The wire gauze shall be stretched to tighten firmly, supply and fixing in the frame at site as per specification and drawing complete all as specified and directed.

Item No 48 All as per item No 47 above -ditto- but fully glazed and gauged window shutter thickness 30 mm (Note : Glass pane shall be measured and paid seperately)

Item No 49 S& F 25 mm thick flush shutters solid core construction, with block board core and plywood face pannel, commercial type on both sides. , complete all as specified.

Item No 50 Cutting holes in brick wall built in cement mortar for inserting hold fasts, depth of embedded postion of hold fast /lugs measured from the face the jambs into the wall exc half brick but n.exc one brick thick and making good the dismantaled portion in cement mortar 1:3 or in cement concrete 1:2:4 type B-1, using 20mm graded stone agg complete all as specified upto six storey height.

Item No 51 S&F mild steel work as in hold fast 25x3mm flat iron and similar articles conforming to Fe-410-0, complete all as specified.

Item No 52 Dismantling boarding any description (board/plywood) fixed in any position with screw, complete all as specified

Item No 53 M&L for 18/19mm thick block verneered board core grade 2 quality,interior grade,commercial type, fixed with screws to timber frame work as in cup board shutter, loft shutters incl 15mm thick teak wood leaping and necessary rebating for leaf shutters where required including polishing to leaping/rebating complete all as specified.

Item No 54 S&F 18mm/19mm thick pre laminated board core grade 2 quality interior grade decorative type with decorative face veneer on one face fixed with screws to timber frame work as in cupboard shutter, loft shutter with and including 15mm thick tea wood leaping on edge and necessary rebating for leaf shutters where reqd including polishing to leaping/rebating complete all as specified and directed

Item No 55 S&F factory made PVC frame of size 75x40mm with wall thickness of 4mm made out of extruded 4mm thick plain or prelam PVC sheet reinforced with 15x15mm MS square tube of 19 gauge thickness through out the frame and mitred cut and two corners and jointed with two nos of 150mm long bracket of 10x10mm MS Square tube. The door frame shall be fixed to the wall using 65x100mm long MS screws though the frame by using PVC fastners minimum of four Nos of screws to be provided for each vertical members and minimum of two nos of screws to be provided horizintal members etc complete all as per manufacture instructions and directed.

Item No 56 S&F 18/19mm thick PVC moulded solid board one side pre-laminated for cabinet boxes etc with self and shutter full size fitted under/above the kitchen cooking platform and other platform directed incl provn of fixing arrangement etc, complete all as specified and directed.

Item No 57 Providing and fixing factory made uPVC any colour fixed window/ventilator made of extruded profiles with wall thickness of 2.3mm ( + 0.2mm). Window profile with hollow section with multi chamber, Frame (60mm x 58mm), T Profile ( One vertical length in between two shutters) (60mm x 74mm).Glazing bead (35mm x 20mm) will be mitred cut and fusion welded at all corners, including railing of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 + 0.2mm thick galvanised steel frame (28mm x 21.5) , sash (31mm x 27.5mm), T Profle (27mm x 17mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasterners including 5mm thick toughened glass with single glazing bead and weather seal and required accessories. Note: Net opening will be measured for payment purpose.

Item No 58 Providing and fixing factory made UPVC any colour casement (Double rebated) window area n exc 1.00 sqm each made of extruded profiles with wall thickness of 2.3mm ( + 0.2mm). Window profile with hollow section with multi chamber, Frame (110mm x 38mm), Glass Sash (60mm x 78mm) another mesh sash (50mm x 77mm),T Profile ( One vertical length in between two shutters) (60mm x 74mm).Glazing bead (35mm x 20mm) will be mitred cut and fusion welded at all corners, including railing of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 + 0.2mm thick galvanised steel frame (26mm x 10mm) , sash (31mm x 27.5mm), T Profle (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasterners. Hardware (Casement handle made of zinc alloyed (any colour powder coated), transmission gear made of mild steel with multi point locking system ) 5mm thick toughened glass/frosted glass with single glazing bead and weather seal , Stainless steel wire cloth 0.36mm nominal dia of wire and avg width of aperture 1.40mm and required accessories. Note: Net opening will be measured for payment purpose.

Item No 59 Providing and fixing factory made uPVC any colour sliding window Three track of area n exc. 2.00 Sqm each made of extruded profiles with wall thickness of 2.3mm ( + 0.2mm). Window profile with hollow section with multi chamber, Frame (88mm x 52mm), Sliding sash (42mm x 67mm), Sliding mesh sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm).Glazing bead (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including railing of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 + 0.2mm thick galvanised steel frame (30mm x 18) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasterners. Hardware (Touch lock of zinc alloyed (any colour powder coated), steel roller system, including 5mm thick toughened glass with single glazing bead and weather seal , Stainless steel wire cloth 0.36mm nominal dia of wire and avg width of aperture 1.40mm and required accessories). Note: Net opening will be measured for payment purpose.

Item No 60 S&F Factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement

Item No 61 Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

Item No 62 S&F 100 mm long (size) butt hinges, medium weight, cold rolled mild steel, complete all as specified.

Item No 63 S&F in repairs 100 mm long (size) butt hinges, medium weight cold rolled stainless steel of AISI 304 ISI marked complete all as specified and directed.

Item No 64 S&F continuous (Piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 30 mm, complete all as specified.

Item No 65 S&F in repairs 75 mm long L Bihari concealed type hydrauilc hinges incl stainless screw complete all as specified.

Item No 66 S & F in repairs 150mm size double action spring, hinge, mild steel with steel wire spring, stove enamelled black, complete all as specified.

Item No 67 S & F 300 mm long, Mild Steel sliding door bolts,plate type, stove enamelled black, with bright bolts not less than 12mm dia with & including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified.

Item No 68 S&F 300mm long, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed, complete all as specified.

Item No 69 S&F in repair 300mm long, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed, complete all as specified.

Item No 70 S&F 300mm long, stainless steel of AISI 304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and fixed, complete all as specified and directed.

Item No 71 All as per item No. 70 above but 250mm long.

Item No 72 S&F 150mm long mild steel barrel tower bolts stove enamelled black with bright bolt & fixed with screws, complete all as specified.

Item No 73 S&F 150mm long aluminium anodised barrel tower bolt of extruded section, complete all as specified.

Item No 74 S&F 200mm long stainless steel tower bolt of AISI 304 grade of extruded sections complete all as specified

Item No 75 S&F 200mm long aluminium anodised barrel tower bolt of extruded section, complete all as specified.

Item No 76 S & F in repair 200mm long (size) aluminium anodised, barrel tower bolt of extruded section and fixed, complete all as specified.

Item No 77 S&F 150mm size mild steel pressed handles, oval type, stove enamelled black complete all as specified.

Item No 78 S&F 150mm size extruded aluminium alloy handle, fabricated type, anodised, complete all as specified.

Item No 79 S&F 150mm size , stainless steel handle of AISI 304 grade complete all as specified.

Item No 80 S&F stainless steel of floor door stopper with hard drawn steel spring 140 mm long ,complete all as specified.

Item No 81 S&F in repair floor door stopper aluminium body double tounge anodised with hard drawn steel spring 140mm long complete all as specified.

Item No 82 S&F Hasp and staple, 75mm size, safety type, brass with mild steel hinge pin including bolt to hinge plate & fixed with screws, complete all as specified.

Item No 83 S&F in repair Hasp and staple, 75mm size, safety type, brass with mild steel hinge pin including bolt to hinge plate & fixed with screws, complete all as specified.

Item No 84 S&F in repairs 75mm long, extrruded fancy type SS handle of ISI Mark for kitchen cup boards shutters, cabinets, crocery shelf drawers fixed with nuts , screw and washer of mild steel bright finished , complte all as specified.

Item No 85 S&F ball catches with 8mm dia steel ball and brass body and striking plate including letting in and fixed, complete all as specified.

Item No 86 S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with steel wire staples, complete all as specified

Item No 87 S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed stainless steel wire staple, complete all as specified.

Item No 88 Hacking out old broken glass of any thickness size quality or description from wooden frames /Aluminium frame fixed with wooden beads/aluminium beads and M&L 4.00 mm thick sheet galss ordinary quality and glazing with wooden bead/aluminium beads, complete all as specified

Item No 89 S&F 4 mm thick plain sheet glass with wooden beads, PVC beading, aluminium beads, in square n.exc 0.5 Sqm in each pane, complete all as specified.

Item No 90 S&F 4.00 mm thick figured glass, pin head type and glazing with wooden beads, glass putty, PVC beading, aluminium beads, complete all as specified Make : Saint Gobain or equivalent Note : Rates quoted are applicable for G+5 bldgs and bidder has to note this aspect while quoting the rates.

Item No 91 S&F 5.5 mm thick sheet glass ordinary quality in square n.exc 0.5 Sqm each including grinding of edges for crockery cupboard including taking out/ broken glass with roller, complete all as specified.

Item No 92 All as per item 91 above but except glass.

Item No 93 S&F mild steel 150mm ordinary rat tail , rod pattern springs including roller and roller plate complete all as specified

Item No 94 S&F in repair mild steel 150mm ordinary rat tail , rod pattern springs including roller and roller plate complete all as specified

Item No 95 S&F in repair double aluminium channel size 10x20x2 mm, complete all as specified.

Item No 96 S&F MS roller with "C" shape stapple, chromium plated for 5.5mm thick sheet glass complete allas specified

Item No 97 Dismantling of existing wooden pelmet box of any description and size and making good the disturbed surface to match with the existing complete all as specified.

Item No 98 S&F drapery curtain rods extruded aluminum section anodized in gold copper or antique silver 25mm nominal dia of approved quality with two number decorative brackets design as approved fixed in brick/concrete wall with same finished knobs/latto on each end of curtain rod complete all as specified and directed.

Item No 99 M&L for Preparation of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified.

Item No 100 M&L Preparing surfaces of wood and wood based materials steel and iron work new or old, of any description and girth, not otherwise described and treating small articles such as stop, covers, gully gratings, holdfast, ends of posts, back of chowkats etc area not exceeding .1 sq m each with tar or coal tar black paint

Item No 101 M&L for Praparation of old painted surfaces of wood and wood based surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint, complete all as specified.

Item No 102 Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar, all as specified.

Item No 103 M&L cement concret 1:2:4 type B-O (using 12.5 mm graded stone aggregate) as in flooring 25 mm thick, complete all as specified.

Item No 104 Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish,vegitation outside complex (MOD land), complete all as specified.

Item No 105 M&L for coloured glazed ceramic tiles 300x600 x 7 to 8mm thick as in vertical surfaces of wall as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement 10mm thick rendering in CM 1:4 complete all as specified and directed.

Item No 106 M&L for coloured ceramic tiles (Non skid) of size 300x300x 6 to 7mm thick as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including match over and including 15mm thick screed bed in CM 1:6 complete all as directed.

Item No 107 M&L for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

Item No 108 All as per item No 107 above but as skirting over and including 10mm thick rendering in CM 1:4 including demolition of existing PCC/Terrace skirting complete all as specified and directed.

Item No 109 M&L for 20 mm thick black granite stone (pre-polished)work (table rubbed and polished) laid over and including 15mm thick screed bed or bedding layer in CM 1:4 as in steps, Jambs, pillars, window clips, cooking platforms and like, inlcuding pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, front and side of slab moulded and polished complete all as specified and directed. Granite stone slab shall be laid in single piece with rounding of edgesand a grove shall be provided beneath the projection portions of stone slab and provn of hole for gas pipe shall be provided.

Item No 110 M & L for 20-22 mm thick (minimum thickness 20mm ) Machine cut kota single piece stone slab for steps and size 22''x22'' (minimum) for flooring over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab laid over and including 15mm thick screed bed in CM 1:6 and rounding of edges, rubbing and polishing complete all as specified and directed.

Item No 111 M&L for 20 mm thick granite black (pre-polished) mirror polished for (FAÇADE) wall lining and pointing with white cement 1:2 using marbel dust with admixture of pigment to match with the shade of granite stone including cutting and polishing over and including 10 mm thick cement plaster in CM 1:4 including taking down existing tiles or kota stone, colour and size as approved by GE complete all as specified and directed. Note:- Slab should be in single piece and dimension will be as per site requirement.

Item No 112 M&L for 18 to 20mm thick Jaisalmer stone of uniform texture as in strips/ borders in between and around the Udaipur Green Marble flooring over and including 15mm thick screed bed in CM 1:6 including polishing complete all as specified and directed. Note:- Width of Jaisalmer stone strip should be 100 mm.

Item No 113 M&L for 1.20m x 1.20 m x 18 to 20 mm thick machine cut udaipur green stone flooring over and including 20mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polishing, laid in designed complete all as specified and directed

Item No 114 M&L for 18 to 20 mm thick Udaipur green marble laid over and including 15mm thick screed bed in CM 1: 6 as in treads/risers of steps in one piece including cutting, jointing, moulding and granite polishing, laid in designed complete all as specited and directed

Item No 115 Taking up or down 15 mm bore GI tubing and connections complete all as specified.

Item No 116 Taking up or down 20 mm bore GI tubing and connections including cleaning for re-fixing, complete all as specified.

Item No 117 S&F 15mm bore including concealed fittings GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors, pipes should be painted with bituminous paint of approved quality incuding concealed complete all as specified and directed. Note: Pre form, rigid, resin bonded glasswool section of any length to be used for geyser pipe insullation.

Item No 118 S&F 20mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors etc complete, all as specified.

Item No 119 S&F self closing ball bearing telescopic channel of size 22 inch long fixed with screws in cupboards incl all fittings complete all as specified and directed by Engr in charge. Note : Runner/ Channel should be brought Zinc plated and min weight not less than 40 kg in capacity.

Item No 120 S&F Modular Cabinet Kitchen accecories of Stainless steel grade - 304, 6mm size rod thickness including :-(i) Perforated Cutlery basket, (ii) Grain trolley, (iii) Thali basket, (iv) Cup & saucer basket, (v) Glass basket, (vi) Plate basket, (vii) Premium magic corner (viii) Oil Pull out Tray ( Triple basket layer) of size as per site requirement all as specified and directed by Engr in charge. Make : Godrej Interio/Devas Steel Industries/Zuari Furniture/Sleek/Spacewood/Tiara/Ikea or equivalent make approved by GE.

Item No 121 S&F 25 mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors etc complete, all as specified.

Item No 122 S & F 50 mm bore Galvanised Iron steel tubing, medium grade as in spout in short length, complete all as specified.

Item No 123 Dismantling of 75 mm bore cast iron pipe (soil/waste/vent) with fittings etc fixed to walls,ceiling, on floors & from trenches if required including taking out any type of joints complete all as specified.

Item No 124 Dismantling of 100 mm bore cast iron pipe (soil/waste/vent) with fittings etc fixed to walls,ceiling, on floors & from trenches if required including taking out any type of joints complete all as specified.

Item No 125 S & F 75 mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed to walls, complete all as specified.

Item No 126 S & F 100 mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed to walls, complete all as specified.

Item No 127 M&L Extra over CI pipe and fitting if led joint is provide in lieu of cement joint for 75 mm dia bore pipe complete all as specified

Item No 128 S&F in repair 100mm dia (bore of pipe) cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with cement joints, complete all as specified.

Item No 129 S&F in repair 75mm dia (bore of pipe) cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with cement joints, complete all as specified.

Item No 130 All as per item 128 above but fitted with oval access door for 100mm dia (bore of pipe).

Item No 131 All as per item 129 above but fitted with oval access door for 75 mm dia (bore of pipe)

Item No 132 S & F 75mm dia (bore of pipe) branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door, complete all as specified.

Item No 133 S & F 100mm dia (bore of pipe) branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door, complete all as specified.

Item No 134 S&F in repair cast iron floor trap square type with Cockroch Proofing CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm, complete all as specified.

Item No 135 S&F in repair Salt Glazed Stone Ware (SGSW) gully traps square or round mouthed type size 150x150mm including excavation/earth work, bed concrete, surrounding concrete and CI grating, complete all as specified.

Item No 136 S & F Brass CP health faucet Hand Shower (Health Faucet) with 8mm Dia 1.2 Meter Long Flexible Tube and Wall Hook screwed for iron pipe fancy type long body all as specified and directed.

Item No 137 Supply & fix in repair PVC connection pipe of 15mm x 600mm size with 2 Nos brass check nuts with washers, complete all as specified.

Item No 138 Supply & fix in repair CP connection pipe of 15mm x 600mm size with 2 Nos brass check nuts with washers, complete all as specified.

Item No 139 S&F in repairs vitreous chinaware coloured wash hand basin with pedestal of size 560mm x 470mm complete including , CP Waste coupling ,waste pipe ,complete fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed by Eng in charge.

Item No 140 S&F in repair vitreous china squatting pan of orrissa pattern long pan size 510 x 400 mm white with "p"or "S" trap front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding complete all as specified.

Item No 141 S&F in repair fancy type brass chromium plated toilet paper holder, complete all as specified.

Item No 142 S&F in repair fancy type brass chromium plated soap dish, complete all as specified.

Item No 143 S&F in repair CP grating 125mm dia, complete all as specified.

Item No 144 S&F in repair aluminium peg set of 6 peg, 45 centimeter long, complete all as specified.

Item No 145 S&F in repair fancy type 15mm dia brass chromium plated mixer for mixing hot and cold water screwed down for iron pipe and fixed to WHB including taking out existing mixer from old WHB, complete all as specified.

Item No 146 S&F in repair chromium plated brass 2 way bib cock (two in one) (quarter turn) suitable for 15mm bore pipe complete all as specified and directed.

Item No 147 S&F in repair 15mm bore chromium plated wall mixer hot & cold L bend 3 in 1 pattren fixing and connection to pipes, complete all as specified and directed.

Item No 149 S&F in repair fancy type 15mm bore chromium plated fancy type wall mixer hot & cold with long swan for kitchen sink fixing and connection to pipes complete all as directed.

Item No 150 S&F in repair fancy type chromium plated brass angle valve (quarter turn type )suitable for 15mm bore pipe complete all as specified

Item No 151 S & F in repair fancy type 150mm size square brass CP shower rose complete all as specified.

Item No 152 S & F in repair fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP bracket gaurd and railling 60 cm long complete all as specified. Make: Cardin or Equivalent

Item No 153 S&F in repair fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with screws fancy type complete all as specified .Make: Cardin or Equivalent

Item No 154 S&F in repair fancy type glass corner 250mm radius of 10mm thick toughned glass with CP railing fixed with screws fancy type complete all as specified .

Item No 155 S&F in repair fancy type stainless steel towel rack of AISI 316 grade size 600mm X 300mm including apair of brass bracket complete all as specified and directed.

Item No 156 S&F stainless steel of AI SI 304 grade tubular towel ring including apair of CP brass bracket complete all as specified .

Item No 157 S&F in repairs bib tap with crutch or butterfly handle, screwed down, screwed for iron pipe, 15mm bore fancy type, (quarter turn) cast copper alloy, chromium plated long body with flange complete all as specified

Item No 158 S&F in repair PTMT bib tap fancy type with flange 15mm dia (quarter turn) screwed for iron pipe or for brass ferrule complete all as specified.

Item No 159 S&F in repair stainless steel sink with drainage board of AISI 316 grade made out of 1.00mm thick sheet for kitchen with plug, washers, waste pipe including connecting union overall size 1145mm x 510mm x 200mm with bowl size 510mm x 400mm x 200 mm including taking out existing sink with waste fittings complete all as specified.

Item No 160 S&F stainless steel kitchen plate rack of AISI 316 grade having four shelves made out of stainless steel sheets 1 mm thick over all size 120x90x25cm complete all as specificed and directed.

Item No 161 Dismantling of PVC water tanks of capacity exc 500 litres and n.exc 1000 litres capacity of any condition or type complete all as specified and directed.

Item No 166 Disconnecting existing tanks of exc 500 ltr and n exc 1000 ltr capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately)

Item No 162 S & F 1000 ltr capacity rotational moulded polyethylene water storage tanks tripple layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I.

Item No 163 S&F 20mm Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed. Minimum wt 20mm-210grm

Item No 164 S&F in repairs of 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

Item No 165 S&F in repairs of 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

Item No 166 S&F in repairs PVC moulding to MS flat railing thickness not less than 5mm and width upto 100mm.

Item No 167 S & F Steel windows and ventilators with side hung glazed and wiremesh shutters with Z section including projecting type hinge with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded. Note : - Net opening will be measured for payment.

Item No 168 Dismantling of floor size not exceeding 4.00 Sqm mtr for EWC water closet and removing out the cinder/concrete from sunken protion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditons, grinding any sharp edges etc all as specified and directed. (b) Cleaning or RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (c) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or MAPEI. (d) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus or approved make as specified. (e) M&L for providing 25mm bore GI pipe spout projecting at least 150mm beyond outer face of wall. (f) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (g) The area of Each WC portion is n.exc 4.00 Sqm each. (h) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. Note : The work will be executed by authorised manufacturers/applicator.

Item No 169 Dismantling of floor size not exc 1.50 Sqmtr for IWC Water closet and removing out the cinder/concrete from sunken protion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditons, grinding any sharp edges etc all as specified and directed. (b) Cleaning or RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (c) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or MAPEI. (d) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus or equvalent approved make as specified. (e) M&L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall. (f) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (g) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. Note : The work will be executed by authorised manufacturers/applicator.

Item No 170 Dismantling of MS grill of parapet railing, any description not otherwise provided for complete all as specified upto six storey height..

Item No 171 S&F Stainless steel grill(Grade- 304) using 10mm thick square bars ( 100 mm C/C) of weight not less than 0.62 kg/RM including necessary frame and accessories for window and ventilator grill complete all as specified and directed.

Item No 172 M&L for Preparation of new steel and iron surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of redoxide primer, complete all as specified.

Item No 173 M&L for Preparation of old painted surfaces of steel and iron surfaces of any description over 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint, complete all as specified.

Item No 174 M & L for providing precast reinforced cement concrete jallies 45 mm thick including all mouldings type B-0 1:2:4(12.5mm graded stone aggreagte) set in cement mortar 1:4, complete all as specified.

Item No 175 S&F of 150 mm dia UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed complete to walls, ceilings or in floors with suitable clamps/bracket including taking down old PVC/CI pipes and necessary cutting through RCC roof and brick work etc (above six storey height) and making good all as specified.

Item No 176 S&F of 150 mm dia UPVC (SWR) bends any radius with solvent joints, complete all as specified.

Item No 177 S&F of 150 mm dia UPVC (SWR) Tee any radius with solvent joints, complete all as specified.

Item No 178 M&L for Provision of letter boxes enclosure of size 1350x1050mm size made up of 19mm thick exterior plywood with backing including necessary frame work with first class hard wood wooden fillets of size 75x50 mm all round and making arrangements to fixing of letter box of size 230x320x150 mm i.e 12 Nos of letter box in one enclosure including two coats of synthetic enamel paint over a coat of pink primer all as specified and directed. Note : Letter box will be paid under supply only item

Item No 179 M&L for 18 to 19mm thick granite stone of size 3' x 2' fixed on wall over 15mm thick screed bed in cm (1:4) and engraved flat Nos and border over the stone for building insignia (letter size 3" to 2") complete all as specified and directed.

Item No 180 M&L cement concrete 1:4:8 type D 2 (40mm graded stone aggregate) as in sub base, hard standing of 75mm thick, complete all as specified.

Item No 181 M&L for 22 to 25mm rubber moulded ultra tiles over 15 mm thick screed bed in cm 1:6 and jointed and pointed in white cement mixed with pigment to match the shade of tiles of flooring all as directed.

Item No 182 Cutting shrubs wild growth, plants not exc 30 cm girth grown on permanet structures and removing same growth right from roots and stopping the recurrence by injecting herbicide Glyphosphate 4+ solution (04 % concentrate) into plant root to eliminate further growth. Application shall be as per manufactureres intructions. The disturbed area shall be repaired with PCC (1:2:4) Type B0 mix and surface finished even and smooth in cm 1:4 incl applying two coats of matching finish i.e.Exterior acrylic emulsion paint of same shade & finish. Likely minimum number of shrub/plants in each Building is not less than 50 nos . Work in high rise building upto six storiey height complete all as specified and directed at site. Safety instructions will be complied as directed by Engr-in-Charge

Item No 183 M&L for Preparation of new plastered surface of walls and applying two coats of external weather proof exterior emulsion paint over a coat of primer and including a coat of wall putty on plastered surface on walls/ceiling, complete all as specified and directed.

Item No 184 M&L for complete removal of existing old surfaces of wall/ceiling by scrubbing with hard brush and applying two coats of weather proof exterior acrylic emulsion paint over 1-2 mm thick wall care putty and 1 coat of acrylic resistance primer complete all as specified and directed.

Item No 185 Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 100mm internal dia pipe, complete all as specified.

Item No 186 Dismantling of brick tiles or terracing tiles single layer on roof and removing the rubbish outside complex (MOD land) incl removal of vegetation if any complete all as specified and directed.

Item No 187 Demolition of mud in roof, any thickness, including mud plastering and mud phuska under brick tiles at any situation and height, complete all as specified and removal outside of MOD land as directed.

Item No 188 M&L for PCC 1:2:4 (using 20mm aggregate) type B-1 as in levelling course using WPA finished even and smooth without using extra cement (WPA shall be measured and paid seperately)

Item No 189 M&L for APP based polymeric membrane mineral slate finish minimum weighting 3 kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) over one coat of 85/25 bitumen @1.2 kg/sqm and paste the membrane with torching method and again apply a coat of 85/25 bitumen @ 1.2 kg/sqm at overlapping joints

Item No 190 M & L for supreme quality Heat Resistant Terrace Tiles of size 250x250x 20mm thick ,tiles are specially developed to integrate seamlessly with the concrete roof to provide an efficient solution for hot climatic conditions for residential accommodation. The eco efficient tiles are made from premium grade materials under strict quality supervision. Further, these easy to install tiles are suitable for retrofitting projects over 15mm thick screed in CM 1:4 complete all as specified and directed. Note : - Make of tile will be best quality as approved by GE

Item No 191 M & L Cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in roof kerbs or mud stops etc including weathering slightly rounded or chamfered edges, finished even and smooth without using extra cement including form work complete all as specified.

Item No 192 Taking down existing steel rolling shutter incl hood cover pull & push type not exc 12 Sqm area of clear opening and cleaning the sides of shutters suspensions shafts,anti-guide channels and greasing all the moving parts of rolling shutters and straightening rolling shafts and replacement of bolts and nuts as required for smooth functioning of shutters and refixing the same incl hood cover complete all as specified and as directed.

Item No 193 S& F in repairs mild steel lock plate & handles made of of Flat iron 35 X 5 mm incl welding and painting with two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Item No 194 S & F in repairs mild steel helical wire springs (confirming) as to IS-6248-1970) for shutters not exc 12 Sqm of approved make complete all as specified.

Item No 195 S & F in repairs 3.15mm thick mild steel bracket plate hexagonal or circular in shape incl welding complete all as specified and directed by Engineer-in-charge.

Item No 196 S & F in repairs mild steel hood covers made out of mild steel sheets 1.00mm thick incl bending the sheet to the reqd shape and fixing the same to the folling shutters bracket plate incl one coat of oxide primer and 2 coats of synthetic enamel paint complete all as specified and directed by Engineer-in-charge.

Item No 197 S & F in repairs mild steel roller ball bearing (ISI marked) for 50/40 mm dia pipe shaft complete all as specified and as directed by Engineer-in-charge.

Item No 198 S&F in repairs mild steel clips (Local name Chidiya) made out of 1.00mm thick MS sheet and revetting the same to the existing steel lath of shutters complete all as specified

Item No 199 S & F in repairs MS Black pipe 40mm dia medium grade for rolling shutters shaft incl drilling holes for fixing springs and welding to MS brackets plate compelete all as directed by Engineer-in-charge.

Item No 200 S & F in repairs mild steel pully for 40mm/50mm bore pipe (of approved make) for rolling shutters complete all as directed by Engineer-in-charge.

Item No 201 S&F in repairs of interlocking lath section formed from rolled MS strip 1,2mm thick for rolling shutters above 3.5m width complete all as specified and as directed.

Item No 202 S & F in repair of steel rolling shutters without ball bearing as specified including top cover anchoring rod hasp & staple and one shop coat of primer before erected in position as directed complete manual type thickness of lath 1.25mm.

Item No 203 Excavation in trenches n exc 1.5m wide and n exc 1.50m in depth for foundation etc and getting out in soft/loose soil complete all as specified.

Item No 204 Demolition and breaking up drain pipes (salt glazed stoneware,asbestos cement or reinforced concrete set in cement mortar internal dia of pipe 150mm complete all as specified.

Item No 205 Returning filling in, incl spreading levelling watering and well ramming in layers n exc 25cm (after the pipes have been laid and tested) in soft/loose soil complete all as specified.

Item No 206 Removing excavated materials to a distance exc 1.50 Km but not exc 5 Km outside defence land and depositing where directed.

Item No 207 M&L PCC 1 : 4 : 8 type D2 using 40mm graded stone aggregates as in foundation of manholes, posts etc complete all as specified.

Item No 208 M&L for PCC 1 : 2 : 4 type B2 using 40mm graded stone aggregates as in surfaces channels and drains complete all as specified.

Item No 209 Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement incl forms, moulds, mitred/stoped ends etc complete all as specified.

Item No 210 S&F DWCPE(SN4) 150mm dia (Internal Dia) pipes,snap fit coupler and rubber ring incl testing and laid and properly jointed laid in trenches to a level on concrete bed complete all as specified. Note : The DWCPE (SN4) pipe shall conform to IS 14930 and of best quality as approved by GE. The DWCPE shall consisst of two layers. The outer layer will be corrugated and inner layer shall be plain and smooth. DWCPE pipe and fitting with the scope of this specification shall be so designed and constructed that in normal use their performance is reliable and without damage to the user or surrounding and shall be laid as per manufacturer instructions.

Item No 211 M&L for Providing & injecting chemical for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in a portion with cement mortar 1:2 to match the existing apron complete all as specified and directed.

Item No 212 M & L for Post Construction anti termiteTreatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same ®

Item No 213 M & L for Post Construction anti termiteTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor sall as specified and directed.

Item No 214 M&L for followings :- (i) Removing plaster & finishes all around the coloumns, slabs & beams (on all four sidescription of column to full height , three sidescription of beam to entire span & bottom of slab to area as directed) (ii) After cleaning gently removing cover concrete using pneumatic/electric chipper or any other approved tool in entire portion of structural member (removal of cover concrete shall be done to an extent when reinforcement is visible) (iii) Removal of cover concrete with under cutting of up to a depth of 20mm beyond reinforcement around full circumference & full length of bar where directed. (concrete shall be stripped to an extent concrete substrate is exposed) (iv) Cleaning exposed concrete substrate by using water jet. (v) Removing visible rust along the length of reinforcement using hand tools as approved. Supply & applying of rust removing chemical to remove rust from existing reinforcements. (The Engr-in-charge may order sand blasting if rust is approved) (vi) Any other work as directed by Engr-in-charge to present clean surface for determination of type of repair to be carried out complete all as specified and directed.

Item No 215 M&L for providing rust proof /anti corrosive treatment to bars :- (i) cleaning of all exposed bars (new & old) alround (ii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer (iii) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating.

Item No 216 M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

Item No 217 M&L for treatement of cracks found in the core concrete :- (i) Opening of crack by making a ' V' notch/groove of size 12mm x 12mm over the entire length of the crack as identified by the Engr-in-charge. (ii) cleaning ' v' notch/groove of all dust/debris/loose material (iii) Drilling hole of 16mm dia and about 40mm deep along the length of crack @ (300 mm c/c or thickness of structural member whichever is less) Note : In case length of crack is found less than 300 mm then min 2 holes shall be drilled. (iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole drilled above and fixing the nipple with the help of fast setting epoxy putty. (v) seal the surface around the nipple and the area of crack between successive nipples polymer modified mortar to ensure that there is no leakage from any gap. (vi) Allow the polymer modified mortar to cure for 24 hours and ensure that firmly fixed in postion. (vii) cleaning nipple one by one commencing from the top to bottom in case of column and one by one in alternate direction incase of beam/slab using blow compressed air followed by water injection. It is to be ensured that there is no obstruction in free flow of grouting materials complete all as specified and directed.(viii) Injecting " resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin. Note : pressure shall be in the range of 1-2 kg/sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardenere shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly. (ix) Allow entire effected surface to cure for 24 hours. (x) cutting out projected parts of the nipple & seal the hole in the nipple with epoxy putty as recommended by manufacturer. (xi) cleaning exposed surface of substrate off any dust /loose material after ageing of the grout as recommended by manufactuer.

Item No 218 M&L for treatement of core concrete when found to be porous/honeycombed :- (i) Marking the area in marker as directed by the Engr-in-charge. (ii) Drilling holes of 16mm dia in an orthogonal grid on exposed cone of member @ 150 mm c/c both way, depth of the hole shall be about 60% of the element thickness. (iii) clean the drill hole using compressed air removing the dust/dirt. (iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole with the annular space around the nipple sealed with epoxy putty. It shall be ensured that the injected grount does not leak. (v) Allow the nipple to cure for 24 hours. (vi) Injecting " Resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin. Note : Pressure shall be in the range of 2-3 kg/sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardener shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly. (vii) Allow entire effected surface to cure for 24 hours. (viii) cutting out projected parts of the nipple & seal the hole in the nipple with epoxy putty as recommended by manufacturer. (ix) cleaning exposed surface of substrate off any dust /loose material after ageing of the grout as recommended by manufactuer.

Item No 219 Supply & fixing 12mm dia steel shear connector in grid pattern in between old core and new concrete as wherever directed by Engr-in-charge and as specifed by manufactuer including drilling hole of depth of 100 mm and chemical anchoring with pure epoxy resin anchoring mortar (The cost of drilling hole &chemical anchoring with epoxy resin is inclueded in this item) complete all as specified and directed.

Item No 220 M&L for Providing & Pouring Micro concreting M-40 grade :- (i) Dry concrete substrate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound concrete substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above pour Micro concreting M40 grade, using approved mixing machines/pumping under pressure via approved pneumatic pump at the locations to be repaired in RCC beams & columns etc,. Adding of aggregates will be permitted only as per manufacturer’s recommendation without compromising the strength. The rate shall include cost of all materials (except re-bar) labour charges for mixing, pouring concrete, cost of tools, lead & lift of materials, transportation etc., to carry out the complete work complete all as specified and directed. Note : The cost of micro concrete M-40 grade & Epoxy bond coat is inclueded in this item.

Item No 221 M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 8 mm dia bar - drilling length 80 to 100 mm Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc complete. (The cost of drilling hole & chemical anchoring with epoxy resin is included in this item)

Item No 222 M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 16 & 20 mm dia bar - drilling length 160 to 180 mm Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete complete all as sspeified and directed. (The cost of drilling hole & chemical anchoring with epoxy resin is included in this item)

Item No 223 M&L for use & waste of form work using steel sheets , steel bracing, propping etc around structural members where micro concreting to be done and keeping form work in position till required specified period complete all as specified and directed. Note : Form work shall be 100% leak proof. For purpose of payment area in touch with concrete shall be measured.

Item No 224 S&F for stengthening existing reinforcement by use of mild steel bars of any dia , cut to length, bent to shape required, including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Item No 225 M&L for chipping of spalled and loose concrete and cleaning rust from re-inforcement by sand brushing scrubing down concrete surfaces with wire brushes cleaning with water allowed to dry applying a layer of zinc rich epoxy primer as antirust on all exposed reinforcement followed by a layer of bonding coat of a layer of epoxy adehessive on complete exposed surfaces of concrete and provide guniting in two layers over steel welded mesh 2 mm dia of wire and total aperture 75 mm, thickness of gunite n.exc 25 mm thick (average thickness) using cement mortar 1 :3 with OPC 43 grade cement mixed with polycrete admixture @ 2 % by wight of cement or as per manufactures instructions and finally applying cement plaster over gunite surfaces of required thickness to give an even uniform and smooth finish conforming to proper Geometrics in cement mortar 1:4 to match with the existing surface as in side and soffits of slabs,chajjas,fins,facias ,parapets ,columns and beams etc complete including necessary scaffolding ,shuttering necessary chased to brick work or RCC members at any height upto four storey buildings incl removing of small trees shrubs etc all as specified(Note: steel welded mesh to be welded with the existing reinforcement. The cost of welded meshis to be welded with the existing re-inforcement is deemed to be included in the quoted rate complete all as specified and directed.

Item No 226 S&F in repair vitreous China coloured European type WC with floor mounted (single piece)including connection to drain, P/S trap and fixing bolts ,plastic water closet seat cover complete all as specified.

Item No 227 S & F in repair 500 ltr capacity three layer white colour rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling old water tank all as specified in SSR Part I

Item No 228 M&L 75 mm PCC(1:4:8) type D2 using 40mm graded stone aggregate as in sub base of floor and filling as mass conc.

Item No 229 M & L Machine pressed precast concrete interlocking paver block with gray cement and PU coated any shape and size confirming to IS 15658-2006 of 80mm thickness M-40 Grade complete all as specified

Item No 230 M & L sand filling under floors or in foundations including watering and consolidation.

Item No 231 S&F steel work in tubular trusses including special shape washer etc complete using ERW or induction butt welded tubes including painted one shop coat of zinc chromate primer paint (including preparation of surface ) at conractrors workshop before fabrication conforming to IS 1161-1679 grade St-240 complete all as specified and directed.

Item No 232 S&F MS Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angels, as necessary gusset plates riveting etc n. Exc 10 kg each to be measured under stuctural steel.

Item No 233 Taking down carefully copper/aluminium point wiring (light/fan/ socket/power) complete from the wall by cutting/ chasing including fittings and fixtures such as switches, ceiling roses, pendants holder, regulators,sockets,light fittings etc for credit and making good the disturbed surfaces of wall, floor etc complete all as specified and directed.

Item No 234 Taking down carefully sub main wiring of any description.

Item No 235 Disconnecting electric & water supply connections, nuts-bolts & taking down Geyser different capacity and shifting to MES store yard.

Item No 236 Disconnecting elect connection and taking down of ceiling fan / Exaust fan of any make and any height, dismantling blade and removing fan alongwith blade for depositing in MES store yard complete all as specified and directed by Engr- in- Charge.

Item No 237 Taking down defective switch fuse main board /MCCB Enclosure/ distribution iron clad or sheet metal enclosure/ MCB DBs with MCBs of any capacity and make including wooden board etc complete all as specified and directed.

Item No 238 M & L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through new PVC conduit 20 mm dia medium grade ISI marked and all conduit accessories concealed in walls/ceiling/fixed to roof/truss/columns etc and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuty, fabricated branded modular metal flush box duly make embossed, concealed in walls with suitable modular inner and outer plate for housing switches , socket out let and fan regulators etc, complete all as specified and as directed for the followings:-

(a) One light /Ceiling fan/exhaust fan point controlled by one, one way switch .

(b) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on same board

(c) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on independent board.

(d) One bell point controlled by one bell push.

(e) One light point controlled by two Nos two way switches

Item No 239 All as per item No.238 herein before but with 4 Sqmm cable for one 3 pin 15 Amp switch socket outlet and using 4 sqmm PVC single core copper conductor cable multistranded as earth wire complete all as specified and directed. Note for Item 238 & 239 : (i) In case the wiring is encountered with any beam/column, then the wiring will run on PVC casing/caping to avoid any damage to the RCC portion. (ii) No cutting shall be done in the roof for laying PVC conduit for ceiling fan point wiring, in this specified portion wires shall run through the surface new conduit shall be provided as mentioned in note (i) above. (iii) Proper colour code will be used for wiring as per the electrical rule and as directed by EIC.

Item No 240 M&L switch Modular type 6 Amps 230V AC complete all as specified and directed by Engineer in charge.

Item No 241 M&L switch modular type 6 amp SP two way complete all as specified and directed by Engineer in charge.

Item No 242 M&L Modular socket outlet 5 pin 6 Amp socket 2 module complete all as specified and directed by Engineer in charge.

Item No 243 M&L switch bell push Modular type 6 Amps 1W-1 module, 230V AC complete all as specified and directed by Engineer in charge.

Item No 244 M&L switch Modular type 16 Amps 230V AC complete all as specified and directed by Engineer in charge.

Item No 245 M&L Modular socket outlet 5 pin 6/16 Amp universal socket 2 module complete all as specified and directed by Engineer in charge.

Item No 246 Supply & Fix Modular five stepped type electronic fan regulator 2 module 360 degree rotatable type 230V AC complete all as specified and directed by Engineer in charge.

Item No 247 S&F Modular double USB charger 2 module 2400 Ma confirming to IS 13252 (Part - 1) complete all as specified

Item No 248 M & L for Point wiring with PVC unsheathed multi stranded copper conductor cable 1.5 sqmm (nominal dia ) 1100 volts in new PVC conduit 20 mm dia medium grade ISI marked and all conduit accessories concealed in walls/ceiling/fixed to roof/truss/columns etc and and new MS steel terminal boxes not less than 1.6 mm thick of required size (factory made) terminal boxes concealed in walls and with top cover of 3 mm thick hylam sheet of white colour including one run of 1.5 SQMM FRLS 1100 Volts copper conductor cable (green colour) as earth continuity connected to common earth for one light point complete all as specified and directed by Engr-in-Charge for the followings:- Note : (i) In case the wiring is encountered with any beam/column, then the wiring will run on PVC casing/caping to avoid any damage to the RCC portion. (ii) No cutting shall be done in the roof for laying PVC conduit for ceiling fan point wiring, in this specified portion wires shall run through the surface new conduit shall be provided as mentioned in note (i) above. (iii) Proper colour code will be used for wiring as per the electrical rule and as directed by EIC.

(a) One light /Ceiling fan/exhaust fan/ bell point controlled by one switch.

(b) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on same board

(c) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on independent board

(d) One light point controlled by two Nos two way switches

Item No 249 M&L switch piano flush type 5 amp SP one way ISI marked.

Item No 250 S & F switch piano, flush type, single pole, Two way, 5 Amps 230Volts ISI Marked complete all as specified and directed by Eingr-in-Charge.

Item No 251 M&L socket outlet 5 Amps 5 pin flush type ISI marked

Item No 252 Supply & Fix fan regulator electronic step type 5 steps piano type, one module connecting complete all as directed.

Item No 253 S&F ceiling rose, PVC/Polycarbonate isolated body with three terminals.

Item No 254 M&L bell electric (ding dong) 230 volt, SP all as specified and directed.

Item No 255 S & F sheet metal enclosure single pole and Neutral with a two pin earth plug top and socket complete with a MCB SP 20 Amp, "C" Curve 220 volts, 50 Hz, 10KA breaking capacity complete all as specified and directed.

Item No 256 Supply and fix LED batten luminaire surface mounted, 4 feet system wattage of 20-22 Watts with lifetime of 50000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.95, THD< 20%, colour temperature - 6500K, surge protection 3KV in CM, IP-20 protected, meets LED IS specifications, Class - 1, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 DegreeC, system efficacy at luminarie level >105 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete. Note- All the above mentioned specification will be verified through LM 79 and LM 80 report of NABL accredited lab before supply of LED fixtures

Item No 257 S&F in replacement of LED batten luminaire surface mounted 2 feet system wattage of 9/10 watts and not less than 1000 lm with life time of 50000 burning hours with 70% of its initial lumen maintained. CRI > 80, power factor > 0.95, THD < 10%, color temperature > 6500 K , surge protection 2.5 KV in CM IP- 20 protected meets LED IS specifications, voltage range-150 to 270 volts AC, temperature range 0 to 50 Degree C,system efficiancy at luminarie level ≥100 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed complete all as specified and directed. Note- All the above mentioned specs will be verified through LM 79 and LM 80 report of NABL accredited lab before supplyof LED fixtures”

Item No 258 S&F in replacement of decorative type wall mounted luminaire with unbreakable poly carbonate materials with 1x14 watt LED bulb B22 Base, complete all as directed.

Item No 259 S&F in replacement of LED 10 watts bulkhead fitting with powder coated die cast aluminium housing with glass/ non yellowing polycarbonate cover, IP65 Protection, System level efficacy of the Luminary is >100 lm/W with a life class of 50,000 burning hours at L70 criteria, Power Factor >0.95,driver with Voltage range 150- 270V, Temperature range 0 to 50 Deg, Driver efficiency >85%, THD<20%, CRI>80, Color Temperature-6000K, Surge protection of 4 KV, including connecting up with necessary PVC sheathed 3 core 1.5 Sqmm copper conductor flexible wire fixed complete all as specified and directed.

Item No 260 S & F in replacement of surface ceiling mounted, round LED down light fitting 15 watts with die cast aluminium housing and system wattage of 12W, system efficacy at luminary level ≥100 Lumens/watt, 50000 burning hours, 6500K color temperature with CRI >100, Power Factor > 0.90, Driver should meet IEC compliant for safety with multi stage high Isolate CC-CV operated driver with voltage variation range - 150 to 270 Volts AC, and surge protection of 3 KV, and including connecting up with PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete all as specified and directed. Note- All the above mentioned specs will be verified through LM 79 and LM 80 report of NABL accredited lab before supply of LED fixtures

Item No 261 M&L for angle Lamp holder with metalic ring, pvc/ polycarbonate type back plate with LED bulb 09 watt, 900 lumens out put, 6500K suitable for B-22 base all as per directed

Item No 262 S&F 30W High efficient LED Street light fitting with pressure die cast Aluminum housing and has lenses specially designed for Street Lighting with polycarbonate cover. System level efficacy of the Luminarie should more than 110lm/W. The color temperature is around 6500 K with a color rendering index of 70. The luminaire is IP:66 protected. It has an electronic driver complaint to IEC safety standards with a power factor>.0.9, voltage variation range 120-270V, THD<10%, High and low protection along with a surge protection of 4 KV including provision of suitable dia GI light grade pipe1.5 meter length bend to shape and necessary clamps etc for fixing the light fittings on wall fixed complete as specified and directed. Note- All the above mentioned specs will be verified through LM 79 and LM 80 report of NABL accredited lab before supply of LED fixtures

Item No 263 S & F water heater storage type (Geyser) vertical type with suitable size of fastner and incl provision and connecting up of SS braided pipe with adopter for inlet and outlet water connection, having adjustable knob for temperature control and inner tank material of superior glass lined tank and outer body material ABS with high pressure with standing capacity upto 8 bar pressure complete all as specified of capacity 25 ltr having heating element 1.5 KW and not less than 5 star rating.

Item No 264 Supply and fix Instant Hot Water Geyser 3 Ltrs capacity,3 KW with corrosion proof thermoplastic external body ,withstand high pressure capacity to use in high rise buildings, ISI approved with suitable size of fastner and incl provision and connecting up of SS braided pipe with adopter for inlet and outlet water connection complete all as specified

Item No 265 Supply and fixing ceiling fans three blade, Robust and reliable inverter motor (brush less DC Motor) powered by ECM technology, BEE 5 star rating for energy saving, rated Air delivery >220cum/min, AC single phase 230/240 V of size 1200 mm sweep including making connection with three core flexible, copper cable pvc insulated of suitable length, complete all as directed.

Item No 266 Supply and fixing ceiling fans three blade, Robust and reliable inverter motor (brush less DC Motor) powered by ECM technology, BEE 5 star rating for energy saving, rated Air delivery >220cum/min, AC single phase 230/240 V of size 1400 mm sweep including making connection with three core flexible, copper cable pvc insulated of suitable length, complete all as directed.

Item No 267 S&F wall mounted fan 400 aerodynamic designed air delivery ≥ 70 CMM, thermal over load protected motor 3 blade white colour, 230 Volts, 50 Hz 1420 RPM with 90 degree oscillation and having speed & oscillation control by two pull cords system all as specified and directed.

Item No 268 Supply and fixing Ventilating Fan 250 mm sweep, 1250 RPM, non metallic resin body air delivery > 800 CMH,5 number of blades, with 240 volts AC 50 Hz and connecting up complete including louvers and provision of copper cable 3 core of size 0.5 sqmm complete all as specified and as directed.

Item No 269 Supply, and Fixing wall mounted angular Electric chimney black colour of suction power not less than 1220Cum/Hr,Al casette with stainless steel outer layer ,touch control panel,3 speed motor with 250 watt with decorative smart cooker hood SS and glass ,energy efficent Led light with digital display , including ducting not less than 10 feet as per site required complete all as specified and as directed by Engr-in-Charge Make: Elica model kitty Plus or equivalent in kaff/ Hindware

Item No 270 S&F MCB DB SPN 12 way Horizontal, IP - 43, IK 09 Protection double door 240 V AC 50Hz with for MCB SPN as incomer and SP MCBs as out going with tinned copper bus bar ,neutral link earth link complete all as directed by Engineer -in- Charge.

Item No 271 S&F MCB DB SPN 02 way, single door 240 V AC 50Hz, MCB SPN as incomer / out going complete all as directed by Engineer -in- Charge.

Item No 272 S&F MCB SPN 40 to 63 Amps 240 volts 10 KA 50 HZ 'C' curve complete.

Item No 273 S&F MCB SPN 16 Amps 240 volts 10 KA 50 HZ 'C' curve complete.

Item No 274 S&F MCB SP 6 - 32 Amps 240 volts 10 KA 50 HZ 'C' curve complete.

Item No 275 M &L telephone Point wiring complete with single pin 0.61mm dia copper conductor cable telephone pain taped and rip conforming to ITD specification D-3003 and ITI-113C/114C cable PVC insulated drawn though PVC concealed conduit not less than 20 mm dia for one 2 pin telephone socket out let on independent modular type board complete all as specified and as directed.

Item No 276 Supply & Fix in repair RJ-11 Telephone socket with transparent shutter 1 module on phenolic laminated sheet etc as required complete all as specified and as directed.

Item No 277 S&F PVC telephone Junction box suitable for 2 incomming and 2 outgoing connection complete.

Item No 278 Supply, and drawing in concealed New PVC conduit not less than 20 mm dia medium duty incl 02 runs of single core 04 Sqmn (for main current& Neutra) and one run single core 04 Sqmm (As earth wire) of multi stranded FRLS conductor copper conductor PVC insulated unsheathed. 1100 votls, ISI marked for sub main wiring.

Item No 279 Supply, and drawing in concealed New PVC conduit not less than 20 mm dia medium duty incl 02 runs of single core 06 Sqmn (for main current & Neutral) and one run single core 06 Sqmm (As earth wire) of multi stranded FRLS conductor copper conductor PVC insulated unsheathed. 1100 votls, ISI marked for sub main wiring.

Item No 280 Supply, and drawing in new PVC concealed conduit not less than 25 mm dia medium grade ISI marked and all conduit accessories concealed in walls/ceiling fixed to roof/truss/columns etc including 2 runs of single core 10 Sqmn (for main current& Neutra) and one run single core 10 Sqmm (As earth wire) of multi stranded FRLS conductor copper conductor PVC insulated unsheathed. 1100 votls, ISI marked for sub main wiring.

Item No 281 Supply, and drawing in new surface PVC conduit not less than 25 mm dia medium duty incl 02 runs of single core 10 Sqmn (for main current & Neutral) and one run single core 10 Sqmm (As earth wire) of multi stranded FRLS conductor copper conductor PVC insulated unsheathed. 1100 votls, ISI marked for sub main wiring.

Item No 284 M&L earthing complete with GI electrode 600x 600 x 6mm, thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below normal ground level (with top edge of earth plate not less than 1.50 mtr below normal ground level connected to GI strip 32x6mm as earthing lead by means of bolt nuts, check nuts, and washers of brass connected including gun metal or phosphorus bronze of size 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25 mm long hexagonal head screwed all as specified including excavation and earth work and disposal of surplus soil incl 40 mm GI tubing light grade and necessary fitting for protection of GI strip incl laying of alternate layer of charcoal dust and common salt PPC (1:2:3) type C-1 (using 20mm graded stone aggregate) for earth pit with 40 x 40 x 6mm MS angle iron frame for cover 40 mm thick (1:2:4) type B20 using 12.5 mm graded stone aggregate reinforced with 8 mm dia round bar @ 75mm C/C both way with MS handle 20mm dia plastering 15mm thick CM (1:6) internally and upto 150mm below ground level externally PGL funnel with ground wire mesh 20mm dia GI pipe Medium grade for watering complete all as shown on electrical plate No 3 of SSR Part-1 2009 and connected in earth test incl testing completed all as specified and directed. Note:- Galvanised strip and protection light grade GI pipe upto 7.5 mtr shall be deemed to be in the rates.

Item No 285 M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recessed or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc of size 32x6 mm thick galvanised strip with duly fixed on suitable size of porcelain/ PVC insulator complete all as specified and directed by Engr-in-Charge.

Item No 286 Supply & fix XLPE insulated PVC sheathed armoured heavy duty electric cable with stranded aluminium conductor 1100 volts grade, cross sectional area 70 Sqmm 3.5 core duly fixed on PVC saddle and spacer complete all as specified and directed.

Item No 287 M&L for fixing of GI tubing medium grade 40 mm bore fixed to wall / ceiling for hanging of ceiling fan (Approx length- 2.3 RM) including suitable size of fan hook as per site requirement and cement work including making good the disturbed surface with existing surface complete all as specified and directed.

Item No 288 S&F factory made epoxy powder coated distribution board (MCCB DB) TPN 4 way vertical type, IP-43, protection made out of min1.6mm thick CRCA sheet, Fabricated, metal double door fixed to wall and suitable for universal monting and including 200 Amps rated copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plated with knockouts and incl MCCB 100 Amps as incomer and confirming to IS : 8623 complete all as specified an directed

Item No 289 S&F in reapirs sheet metal enclosure one way for independent mounting of 4 Pole MCCB, Including MCCB 4 Pole 250 Amps 25 KA, 415 Volts complete all as specified and directed by Engineer-in-charge

Item No 290 Supply and lay in repairs XLPE insulated PVC bedded galvanised steel strip or wire armoured electric power cables(heavy duty) 1100 volts grade with stranded aluminium conductor of size 95 Sqmm 3.5 core including connection of cable at both ends with suitable size of glands, aluminum lugs complete jointing, testing and commissioning complete all as specified and directed.

AMIT ASSOCIATES

Third Wave Services Pvt Ltd