8209-PROVN OF ONE STATIC WATER TANK (SWT) OF 110 KL CAPACITY NEAR BATTALION MAGAZINE AT ARMY CAMP PALLAVARAM, PROVN OF TILES WORK AT CORRIDOR AND VARANDAH AT MH CHENNAI AND CERTAIN OTHER SANCTIONED WORKS AT OTA ,DGQA UNDER GE STM

Amount

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings.

Supply & fixing Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M & L Preparation of old painted steel surfaces and applying one coat of synthetic enamel paint..

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for non skid coloured jointless ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed

S&F glazed ceramic joint less tiles coloured of size 450 x 350 x7 mm thick joint free on vertical surfaces such as dados etc set and jointed in neat cement slurry and pointed in coloured cement, incl screed bed 10 mm thick CM (1:6) all as specified and directed by Engr-in-Charge.

S & F in repair Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap,and to flushing pipe, anti-syphonage pipe,etc. complete including making good to floor

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white( excluding fixing bolts, flushing cistern and flush pipe) all as directed

S & F CP Health faucet with CP connection and hook fixed all as directed. Make :Parry ware Cat No .T9937A1 or equivalent as approved by GE.

S & F PVC valveless, syphonic action type, flushing cistern, low level white, with inlet ball valve, float and handle including brackets 10 litrs capacity.

S&F in repairs vitreous china wash hand basin, white flat back size 550x400mm (excluding taps, waste, pipe chain and plug) but including porcelain stopper and a pair of MS bracket etc complete all as specified.

S&F Bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe, 15 mm bore fixed in repairs all as specified

S&F Pillar taps, CP cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down, high pressure and fly nuts, screwed for iron pipe 15 mm bore and all as specified.

S&F towel rail 600mm long 20mm dia aluminium anodised chromium plated fixed with wooden guities embeded in cement mortar (1 : 3) with steel screws etc, complete all as specified.

S&F PVC connection 15 mm size with PTMT nuts of length 450mm.

S&F in repairs Angle cock cast copper alloy , Chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, 15 mm bore.

M&L in repair GI tubing ISI marked medium grade 15mm bore with all fittings and fixed complete to walls and ceilling or laid under floor including connection etc, complete all as specified .

M&L in repair GI tubing ISI marked medium grade 20mm bore with all fittings and fixed complete to walls and ceilling or laid under floor including connection etc, complete all as specified .

M&L in repair GI tubing ISI marked medium grade 25mm bore with all fittings and fixed complete to walls and ceilling or laid under floor including connection etc, complete all as specified .

M&L in repair GI tubing ISI marked medium grade 40mm bore with all fittings and fixed complete to walls and ceilling or laid under floor including connection etc, complete all as specified .

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth

Taking down chowkats or frames with shutters (without taking off shutters from frames) exc. 1.5 Sqm but n. exc 4 Sqm each including making good disturbed surfaces

S&F Solid PVC Frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling &fixing in opening as per spcification & drawing Note:- i)Existing wall edges will have to be finished properly in cement plaster 1:4 . including fixing of 6 Nos wooden plugs for catch door frame size not exc 17Sqcm average sectional areas and 100mm long. (i)Frame will have to be fixed to the wooden plugs inserted in wall using 6 Nos of 100mm long MS screw, 3 each on either side. (ii)PCC strip of section 5*5mm will have to be created at bottom incl. smooth finish in each door opening.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S frame shall be top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC `C`channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S frame welded / sealed to the stile &rail with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F for 2nd class hard wood for plain, solid, straight chowkats and frames, wrought, framed rebated on the solid put together jonts.

S&F Second class hardwood 35 mm thick plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats.

S&F Butt hinges 100 mm, cold rolled mild steel type all as specified.

S&F Alumininum anodised barrel tower bolts of extruded section 200 mm size

S&F Extruded aluminium alloy handles, fabricated type, anodised 150 mm long

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded sections or cast aluminium alloy and fixed .

Forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete in cement mortar 1:4

M& L PCC 1:2:4 type B1 using 20 mm graded stone aggregate as for holdfasts including necessary formwork

S & F hold fasts, wall tiles hooks, for hanging fans plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165.

Preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

Demolition of Brickwork built in cement mortar including all quoins, arches, pillars, etc, complete all as directed

M&L for plain Cement concrete type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete all as specified.

M&L for Brick work with fly ash bricks straight or curved on plan and 6 metre mean radius built in CM 1:6 all as specified

M&L for Brick work with old size sub class "B" bricks straight or curved on plan and 6 metre mean radius built in CM 1:6 all as specified

M&L for Brick work with fly ash bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:6 all as specified

M&L for rendering 10mm thick in CM 1:6 on otherthan fair faces of brick work or concrete surfaces complete all as specified and directed.

Material and labour for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth with out using extra cement

Complete removal of exisisting treatment on external walls and applying two coat of cement base paint over a coat of alkali resistant priming paint

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors

S&F PVC (SWR) bend 110 MM bore complete all as specified and as directed

S&F PVC (SWR) 75 mm dia pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F PVC (SWR) bends 75 mm bore of any radius complete all as specified and as directed

S&F PVC (SWR), 75mm bore junction single, (Single T) equal or unequal complete all as specified and as directed

S&F PVC (SWR) floor trap plain 75 mm dia outlet with grating including jointing with solvent cement complete all as specified and as directed

S & F Rotational moulded polyethylene water storage tanks 1000 litrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

Ball valves 25 mm high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 25mm-455gms)

Supply & fix gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25mm bore and fixed in repairs all as specified.

Supply & fix gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 40mm bore and fixed in repairs all as specified.

M & L for providing precast cement concrete Type B1 1:2:4 (20mm graded aggregate) in cover slabs and setting in Set in Cement Mortar 1:6 complete with joints to match all as specified.

M & L for Mild steel TMT bars 6 to 8 mm dia of grade Fe 500, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming all as specified

M&L mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming all as specified.

Demolition of cement concrete in ground floor & paving n.exc 15 cm thick below or above GL and removing the debris as directed

M & L for PCC 40mm thick type B-1, 1:2:4 (20mm graded aggregate) finishing with even and fair without using extra cement

M&L for providing 100mm thick, PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in sub base of floors and pavings etc.

S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement;

M&L for preparation of new plastered wall surfaces and applying two coats of white wash over a coat of chalk whitening,on plastered surfaces complete all as specified and as directed

M & L for Preparation of new plastered surfaces of wall and applying two coat of cement base paint over a coat of alkali resistant priming paint

S&F Anodised aluminium snap grid frame work ( Size of grid 605 X 605 mm) for false ceiling all as specified

M & L 8mm Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws all as specified.

Plastic water closet seat, coloured, closed pattern with flat bottom, and cover and MS CP or aluminium hinging device

S&F in repairs CP brass shower rose 125mm size suitable for 15mm bore pipe complete all as specified.

S&F 3 in 1 wall mixer Make : Parryware cat N- G 0317A1.

S&F stainless steel Soap Dish Make : Jaquar AHS-1531

M&L toilet paper holder brass chromium plated as in repair complete .(Make: Jaquar continental Cat No .ACN -1151N -or equivalent.)

S & F Glass shelves for bath room corner set of three all as directed by Engr -in -Charge .

Dismantling stone slabs and tiles of any description or thickness in floors, aprons,in roofs etc.laid bedded and pointed in any mortar

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over 20 mm thick screed bed in CM (1:6) complete.

M&L for machine cut kota stone slab flooring 20-25mm thick in skirting, risers of steps, dado laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over 15 mm thick screed bed in CM (1:4) complete.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, drain, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/ dense soil.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in surface channels and drains.

M&L for Cement concrete type C1 1:3:6 using 20 mm graded stone aggregate in surface channels and drains

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement.

M&L for rendering 10 mm thick in CM 1:4 on brick or concrete surface and rendering is to be finished even and smooth (without using extra cement).

M&L PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in copings, bed plates, watertroughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

M & L for Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slabs (for man holes etc.) water troughs, mangers, and similar articles with plain faces

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Excavating post holes (or similar holes) each n exc 0.5 cu m, getting out in hard/ dese soil, including removing surplus soil to a distance n exc 50m and making good surface.

PCC 1:2:4 type B1 using 20 mm graded stone as foundation, filling and mass concrete.

S& F rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc.. Conforming to FE 410-W (Gde E-250) quality "A"

S/F steel work in tubular trusses,purlins,distance pieces including special shaped washer etc complete using ERW or induction butt welded tube confirming to I S 1161- 1979 GRADE S-240.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe 410-W (Gde-E- 250) quality-B

M&L Preparation of New or previously untreated steel surfaces and applying two coats of synthetic enamel paint over a coat of Redoxide primer.

M&L for slab supported on wall, beams and columns in floors, roofs, landing balconics, canopies, deck slabs and shelves and the like providing cement concrete (1:2:4) type B1 using 20mm graded stone aggregate.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping)

Formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide.

S&F GI tubing medium grade including all fitting and fixed to wall and floor complete as required 15mm bore .

S&F GI tubing medium grade including all fitting and fixed to wall and floor complete as required 20mm bore .

S&F GI tubing medium grade including all fitting and fixed to wall and floor complete as required 25mm bore .

S&F Rotational moulded polyethylene water storege tanks 500 ltrs capacity (cylindrical vertical with closed top ) hoisted and fixed in position all as specified in SSR part- I

S&F 20 mm brass ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrrrule

S&F Gun metal gate valves with iron wheel head screwed both end for iron pipe and fixed 20mm bore .

Surface excavation n. exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in hard dense soil

M&L for hardcore of gauge n exc 63 mm deposited spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface of broken stone or boulders

M&L for providing 100 mm thick PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in, floors and pavings etc incl necessary formwork.

M & L for Precast cement concrete 1:2:4 type B0 using 12.5 mm graded aggregate louvres and jallies, 45 mm thick (measured solid) incl. all moulds set in CM 1:4 complete all as directed

Cement concete 1:2:4 type B1 using 20 mm graded stone aggregate as in bands, seismic and other similar bands incl. weathering slightly rounded or chamfered angles and throating as directed incl. necessary formwork.

M & L Rendering 15mm thick in CM (1:6) on fair faces of brick work or concrete wall surfaces all as specified finished even and smooth without using extra cement

Taking down shutters of any description exc 2.00 Sqm each and re-fixing in same opening after necessary resizing/repairs all as directed by Engr-in-Charge.

Taking down shutters of any description exc 1.00 and n exc 2.00 Sqm each and re-fixing in same opening after necessary resizing/repairs all as directed by Engr-in-Charge.

M&L for vitrified ceramic tiles double charged of dark shade 10mm thick (Square / rectangular) polished area of each tiles not eceeding 0.36 sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM 1:4 adhesive chemical as per manufacturer direction complete all as specified and as directed

M&L for glazed ceramic coloured tiles of size 300x450x7/375x250x7mm thick on vertical surfaces such as dado/skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including providing 10mm thick screed in CM 1:4 complete all as specified and as directed

S&F Powder coated Anodised aluminium (minimum 15 micron) frame for doors, windows, ventilators and grills/guard bars etc with one or more rebates including joining cleat for fixing etc. complete all as specified.

S & F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified

S&F Powder coated Anodised Aluminium window and ventilator shutters, sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminum fittings such as roller, channel, locks/handle complete all as specified

M & L for 12 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws.

S&F Sheet glass 5.5 mm thick ordinary quality and glazing with beading in squares exc 0.5 Sq.m in each pane.

Supply and laying GI tubing of 80 mm bore galvanized medium grade of any length including all fittings such as bend, elbow, tee and union in trenches complete.

Excavating in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation of stays, laying cables etc and getting out in soft / loose soil all as specified and directed

Supply and fix of cast iron 80mm bore sluice valve PN 1.6 both flanged heavy duty drilled and installed with stainless spindle gun metal face rings rubber gasket 3mm thick, MS bolts nuts and washers graphite rope complete.

Cutting the existing 150mm dia CI line in position supply and inserting CI fittings and testing including necessary earth work in sludgy soil, dewatering and refilling the same in layers complete all as specified and directed by Engr-in-charge. Note : CI fittings shall be measured and paid separately under respective item.

M&L for cast iron fittings such as bends tapers to pieces( Single or double) branch pieces any type, straight, connecting pieces, socket, collars, caps, plugs, flanges/spigot with nut, bolts and washers for 80mm to 150mm dia complete including taking down existing fitting complete all as specified and directed.

Construction of masonry valve chamber of size 900X900X1200 mm internal size, 100 mm thick foundation using PCC 1:4:8, type D-2, over 15cm thick hard core, 20cm thick solid block masonry with blocks cast using PCC 1:3:6, type C-1, set in cement mortar 1:4, 15MM thick plaster to internal surfaces and external surfaces up to 15cm below ground level and top of floor in cement and sand mortar 1:4, finished even and smooth with out using extra cement , 3.15mm thick MS sheet cover including 50mmX50mmX6mm thick MS angle frame fixed in PCC 1:2:4, type B1 coping with 25mmX6mm flat iron hold fasts, handle, hinges with locking arrangements, applying one coat of red oxide primer and two coats of synthetic enamel paint to all steel surfaces and earth work in any type of soil including disposal of surplus soil to a distance not exceeding 50M complete all as specified.

Replacement of cast iron 80mm bore sluice valve PN 1.6 both flanged heavy duty drilled and installed with stainless spindle gun metal face rings rubber gasket 3mm thick, MS bolts nuts and washers graphite rope complete including taking down the old unserviceable valves.

Supply & fix in replacement of CI non-return valve of size 80mm bore complete all as specified and directed.

S & F GI tubing heavy grade 80mm dia with all fittings, laying in floor / ceiling / lowering in well in 3 mtr lengths with heavy grade sockets all as directed

Supply and Fix Star delta Starter fully automatic including openwell submersible pumpset 10 HP, 415 volts all as specified.

Excavation over areas, n.exc 1.5m deep and getting out in hard/dence soil all as specified.

Excavation over areas, exc 1.50m deep & n.exc 3m in deep; for foundation etc & getting out hard/dence soil all as specified.

M&L providing reinforced cement concrete design mix M-30 (20mm graded aggregates) as in foundations, incl rafts, footings, foundation beams; plinth beams; bases for columns, etc, basement slabs, and mass concrete.

M&L providing reinforced cement concrete Design mix M-30 (using 20mm graded stone aggregates) as in walls incl columns, retaining walls, basement walls, ballast walls and the like; any thick ness; above top of footings; including attached pillasters and buttresses all as specfied and as directed.

Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits of foundation and plinth beams and similar work vertical or to batter rough finished curved surfaces of concrete

Use and waste formwork to faces of walls, retaining walls, abutments, parapets and similar work incl attached pillasters, etc vertical or to batter rough finished curved surfaces of concrete

M&L plain cement concrete 1:3:6 type C1 using 20mm graded stone aggregates as in plinth protection 75mm thick, finished even and smooth without using extra cement

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 and finished even and smooth without using extra cement mixed with water proofing compound all as directed. (WPC shall be measured and paid separately)

Supply only integral water proofing compound

M&L rendering 15mm thick on fair faces of brick work or concrete sufaces on external wall surfaces CM 1:3 mixing with integral water proofing compound.

M&L for Plain cement concrete design mim M-20 using 20mm graded aggregates 100mm thick as in top surface of raft slab all as specified and as directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns, and stanchions rough finished square or rectangular

Material & Labour coloured Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set jointed and pointed in neat cement slurry in floors with grey cement and pigment incl 15mm cement screed bed CM 1:4 complete all as specified and directed.

S&F Mild steel bolts. Exc 12mm n. exc 20mm purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. exc 30cm long

Supply and fix 12mm thick Perlaminated particle boards, exterior grade perlaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work.

Material and labour 6mm thick teak wood lipping for external of 18/19 thckness of board

S&F 50 mm dia,Polished hardwood knobs fixed with screws

S&F stainless steel rolling wheel with puli as per sutable for cup board/door all as per directed by Engr-in-Charge

Material and labour Preparation of New or previously untreated wooden Surfaces of any description, not otherwise described, over 10cm width or girth applying two coats synthetic enamel paint over one coat of prink primer

Supplied and installed, testing and commissioning of Submersible pumpset 2.0 HP, electric driven AC, single phase,240 V, 50 Hz suitable for open well, 50 mtr head,40 mm dia suction/delivery with necessary submersible copper cable as desired size and length and necessary fixing arrangement complete all as specified and directed.

Supply and Fixing submersible pump starter for running of 02 HP motor, single phase with outdoor type Enclosure and necessary fixing arrangement for inatallation of starter enclosure, all accessories and protection systems for motor(ie OLR, dry run protection etc) complete all as specified and directed.

M & L for construction of brick masonary (230 mm thick wall) valve pipt of size 600 x 600 x600mm inner dimension including necessary earth work , PCC 1:4 8, 75 mm thick Type D-2 using 40 mm graded stone aggregate as in foundation , brick wall build in CM 1:6, rendering 15 mm thick with CM 1: 6 externally upto 15 CM below GL and CM 1:4 internally and providing angle Iron base frame and MS Sheet cover 3.15 mm thick welded with hinges including necessary locking arrangement with handle, in and including dismantling & taking down old unserviceable broken Covers Complete. all as specified and directed by Engr-in-Charge.

M/S.RANGA AND CO