REPAIR / MAINT OF DRAIN, FENCING AND FOOTPATH ETC IN THE AREA OF AGE B/R I UNDER GE (WEST) LUCKNOW

Amount

Demolition of cement concrete (unreinforced) of any description and in any position not other wise specifically provided for complete all as specified and directed.

Dismantling fencing wire mesh any type complete all as specified and directed.

Dismantling/Taking out barbed wire in fencing complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground etc complete all as specified and directed.

M & L for PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M & L for providing reinforced cement concrete type B-1, 1:2:4 (using 20mm graded aggregate) as in pre-cast posts, fencing posts, straining or terminal posts, struts etc. for fencing, average, sectional area exc 100 and n exc 250 sq.cm, with or without chamfered angles and flat, splayed, rounded or mitred tops complete all as specified and directed.

S & F Galvanised 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barb at 75mm spacings and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire staples or steel pins, etc complete all as specified directed (Note :- Each line of wire to be measured).

Labour only for Restraining/resecuring including making good staples, Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire staples or steel pins, etc complete all as specified and directed (Note :- Each line of wire to be measured).

M&L mild steel framed work such as posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting and/or welding etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Supply only mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, 5 to 10mm dia of neck, length of bolts exc. 5cm but not exc 10cm long complete all as specified and directed.

Supply only 3mm dia GI wire chain link fencing of mesh size 75x75mm and any type complete all as specified and directed. NOTE: Weight constant of fencing shall be fixed by BOO.

Fixing only chain link fencing including line wires, any mesh size and type to any type of standards rails, straining bolts, etc. including provn of galvanised mild steel binding wire of 0.9mm dia annealed complete all as specified and directed.

S&F Concertina coil fencing with punched tape coil 450mm dia (at stretched position), made out of hot dipped, galvanised steel wire coated with CLR anti corrosive paint, making diamond shape barbs with 18 SWG sheet, spring core 2.5mm thick wire with tape 0.52mm thick and weight of each coil should not be less than 7.50 Kg, each coil should have 50 rounds and should covers 6 RM length, fixed over and including 6 lines of horizontal RBT (reinforced barbed tape) wire or razor wire at points wherever coil touches the bottom of wire with the help of hog rings (14 SWG) and in between Y shaped angle iron post complete all as specified and directed. NOTE: (i) Hogging shall be fixed at a interval of 600mm centre to centre, wherever it touches with the razor wire. (ii) Overlapping of concertina coil and razor wire shall be 300mm. (iii) Y shaped angle iron post shall be measured and paid separately under respective items. MAKE: M/s Global Engg or M/s Specials steels Ltd or M/s Super Fence or other equivalent make as approved by GE.

Demolition of brick work or stone/ boulder masonary, built in cement mortar or cement lime mortar including all quions, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles etc. complete all as specified and directed.

M&L brick work with old size fly ash bricks of class designation 75, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

All as per item no. 15 above but except bricks. NOTE: Brick retrieved from demolition shall be used

Taking down cement or cement lime plaster any description from walls/ceiling etc including racking out joints, hacking for key & scrubbing down with water all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 with integral water proofing compound @ 3% by weight of cement on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed. NOTE: WPC shall be measured and paid seperately under respective item.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

Supply only integral waterproofing compound complete all as specified and directed.

M&L for two coats of cement base paint over one coat of primer on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for one coat of cement base paint on old treated plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for three coats of white wash on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

M&L Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm in height, copings, kneelers, apex stones, bed plates, water troughs, hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M & L for cement concrete (1:2:4), type B0 using 12.5mm graded stone aggregate as in benching ,haunching for drains etc complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for cutting holes in brick walls built in cement or cement lime mortar for inserting hold fasts, etc and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required; depth of cutting exceeding half brick but not exceeding one brick complete all as specified and directed.

S&F Structural steel framed work with rolled mild steel sections as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing conforming to Fe-290 (Gde E-165) complete all as specified and directed.

Taking down Iron/steel door shutters, side hung exc 1.5 sqm and n. exc 5 sqm and refixing in same opening after repairing including welding and necessary jointing cleats screws etc fittings such as hinges complete all as specified and directed.

Supply and fixing in repair 1.0mm thick PVC plain (colour as specified by Engr-in-charge) sheet including taking down old one in hearth covering to framed steel/iron doors/gates and in partition walls, etc cut to size edges beaded if directed holes punched including round headed screws clout nails or rivets and fixed to steel members complete all as specified and directed.

M&L 1.0mm thick mild steel, plain black sheet in hearths, covering to door shutters, covering to door chowkats (frames), chullah hoods, water tanks, water troughs, ducts, urinal troughs and funnels, etc. cut to size, edges beaded if directed, holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel members, etc. with plain 40mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old or previously treated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed. NOTE: Reinforcement shall be cut as required to facilitate demolition.

M&L for precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves etc and similar works set in cement mortar 1:4 complete all as specified and directed.

M&L Mild Steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild Steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Demolition of PCC in ground floor and paving n exc 15cm thick below or above ground level complete all as specified and directed.

M&L for 40mm thick cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in floor, finished surface even and smooth without using extra cement complete all as specified and directed.

M & L for 38mm wide of glass dividing strips, 3mm thick and inserted in position to confirm design of flooring complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection, laid in panels, finished surface even and smooth without using extra cement and forming 12mm wide expansion joints to the full depth, and filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' complete all as specified and directed.

M&L in repair 35mm thick (measured solid) precast cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in louvres and jallies including all mouldings and similar works set in cement mortar 1:4 complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness, laid, bedded and pointed in any mortar in floors, aprons etc. complete all as specified and directed.

M&L 75mm thick cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub bases of floors and pavings etc. finished even and fair without using extra cement complete all as specified and directed.

M&L for 60mm thick M-35 grade rubber moulded factory made machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 with grey cement and pigment as approved laid over and including 25mm thick sand cushion and joints filled with sand complete all as specified and directed.

S&F Exterior finish floor tiles of size 300x300x10-12 mm thick, superior quality, approved shade, set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed. Make: Endura/ Duracrete/ Naveen/ Eurocon/ NITCO.

M&L for factory made coloured, glossy finish, rubber moulded chequered cement concrete tiles with mixture of white cement and pigments of size 300x300x25mm thick, superior quality, set, jointed and pointed in neat cement slurry with grey cement and pigment as in floor including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M & L Glass coping in repairs with broken glass @ 14 Kg/Square metre fixed in and including 20 mm thick cement mortar (1 : 3) complete all as specified and directed.

Preparation of old external treated surface of concrete/kerb stone surfaces, facias, cornices etc by removing all scale, loose material dust etc & applying one coat of weather proof anti fungal exterior emulsion paint over a coat of putty applied as per manufacturer instruction complete all as specified and directed at site.

M&L for cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

All as per item no. 52 above but add or deduct for each 25mm girth or part thereof over or under 30cm complete all as specified and directed

M/S S&R Construction

R K CONTRACTOR AND SUPPLIERS

M/s J C Oberoi

M/s Chandra Mohan and Sons

M/s SNS Construction

Matrubhoomi Construction

M/S Reliance Construction

M/S SWATI CONSTRUCTION

M/s Sachkhand Traders