CERTAIN MISC REPAIRS TO WATER SUPPLY AND OTHER INSTALLATIONS UNDER GE (NORTH) BIKANER AT MIL STN BIKANER

Amount

Demolition of cement concrete in ground floor and pavings n.exc 15cm thick below or above ground level complete all as specified and as directed by Engineer-in-Charge.

Dismantling plain or corrugated steel sheeting any gauge thickness including nanital or similar pattern complete all as specified and as directed by Engineer-in-Charge.

Dismantling timber scantling over 40 sqcm in section in any position complete all as specified and as directed by Engineer-in-Charge.

As per item No 3 but under 40 sqcm in section complete all as specified and as directed by Engineer-in-Charge.

Taking down cement plaster on brick or conc surfaces including racking out joints hacking for key, scrubbing down with water etc, complete all as specified and as directed by Engineer-in-Charge.

Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) any thickness including covered fillets and supporting members complete all as specified and as directed by Engineer-in-Charge.

Dismantling of Roof tiles of any description or thickness in floor, apron etc laid, bedded and pointed in cement mortar complete all as specified and as directed by Engineer-in-Charge.

Demolition of lime concrete of any description over roof slab complete all as specified and as directed by Engineer-in-Charge..

Demolition of brick or stone masonary including all necessary arches, pillars, quions etc built in cement mortar complete all as specified and as directed by Engineer-in-Charge.

Dismantling structural steel any description including door steel gates etc, complete all as specified and as directed by Engineer-in-Charge.

Demolition of and breaking up of AC rain water pipes any dia fixed in any position complete all as specified and as directed by Engineer-in-Charge.

Raking out joints/pointing to brick work in walls or to bricks on edge in floors, surface channels, roofs, etc, complete all as specified and as directed by Engineer-in-Charge.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons laid in cement mortar etc, complete all as specified and as directed by Engineer-in-Charge.

Taking up or down steel tubing and connections, 15mm bore including cleaning for refixing or removal to store complete all as specified and as directed by Engineer-in-Charge.

Taking up or down steel tubing and connections, 20mm bore including cleaning for refixing or removal to store complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkhat or frames exc 1.50 Sqm n.exc 4 Sqm (without taking down shutters from the frames) complete all as specified and as directed by Engineer-in-Charge.

As per item No 16 above but n.exc 1.50 Sqm complete all as specified and as directed by Engineer-in-Charge.

Taking down shutter only exc 1.00sqm but nexc 2.00 sqm complete all as specified and as directed by Engineer-in-Charge.

Taking down shutter only of any description exc 2.00 sqm complete all as specified and as directed by Engineer-in-Charge.

Taking down shutter only of any description exc 2.00 sqm and refixing the same after easening , greasing in same opening complete all as specified and as directed by Engineer-in-Charge.

Hacking out old broken glasses (Any thickness, size quality, description) from wooden or steel frames fixed with putty or wooden beads complete all as specified and as directed by Engineer-in-Charge.

Roughing surfaces of old conc surfaces by picking up , sweeping,cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @3kg/Sqm including 15 mm thickscreeding in CM (1:4) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separatley) complete all as specified and as directed by Engineer-in-Charge.

M & L Polythene film black 150micron thick complete all as specified and as directed by Engineer-in-Charge.

M & L Applying evenly a tack coat of industrial bitumen 85/25 ,1.2kg/sqm incl cleaning surface complete all as specified and as directed by Engineer-in-Charge.

M & L Lime concrete terracing as specified on roof complete all as specified and as directed by Engineer-in-Charge.

M & L 40 mm thick Brick tiles bedded in 15 mm thick cement and sand mortar (1:6) and joints grouted flush in cement and sand mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and as directed by Engineer-in-Charge.

Roghening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc.

M&L for brick work with sub class 'B' bricks exc 6m mean radius straight or curved on plan built in cement mortar 1:4.

M & L As per item No 28 above but except bricks complete all as specified and as directed by Engineer-in-Charge.

M&L brick work with fly ash bricks straight or curved on plan to any radius built in CM 1:4 all as specified complete all as specified and as directed by Engineer-in-Charge.

M&L brick work with fly ash bricks straight or curved on plan to any radius built in CM 1:6 but except bricks complete all as specified and as directed by Engineer-in-Charge.

M&L Brick work with fly ash bricks (old size) straight or curved on plan to any radius in half brick thick walls built in CM 1:4 but except Bricks complete all as specified and as directed.

M & L Jodhpur stone of roof slabs, self faced 7.5 cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

M & L Sand stone slabs 75 mm in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:3 or cement mortar 1:4, complete all as specified and as directed by Engineer-in-Charge.

M & L Roughly squared stone lintels hammer dressed on face and soffits, hoisted, set and pointed in lime mortar 1:3 or cement mortar 1:6 complete, n exc 3m in length, complete all as specified and as directed by Engineer-in-Charge.

Supply only Chain link MS gavinised fencing any size and type ( Wt 2 Kg/ sqm apprx) complete all as specified and as directed by Engineer-in-Charge.

Fixing only chain link fencing incl line wire any mesh size complete all as specified and as directed by Engineer-in-Charge.

Excavation in post holes(or similar holes) in loose/ soft soil each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exeeding 25cm, watering and removing surplus soil to a distance not exceeding 50m and making good surface complete.

M&L for plain cement concrete type D-2 ( 1:4:8) using 40 mm graded crushed stone agg as in mass concrete and foundation filling complete all as specified and as directed by Engineer-in-Charge.

M&L for Mild steel work conforming to Fe-290 Gde E-165 in nosing to steps including embeding in concrete and screwing etc, wind ties for roof including securing bolts, posts & struts in fencing including cutting top to shape as directed, drilling holes, notching for wire, etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc, complete all as specified and as directed by Engineer-in-Charge.

M&L mild steel round bars 10 mm dia or over, cut to length, bend to shape required, fixed independently to support chain link fencing complete all as specified. Fe 410-0 or Fe 310-0 complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing mild steel work as in flats , ties, straps etc,complete all as specified and as directed by Engineer-in-Charge.

M&L for Mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 75mm long and dia of shank 11 to 15mm complete all as specified and as directed by Engineer-in-Charge.

S&F precasted RCC jallies 25 mm thick (measured solid ) set in cement mortar 1:4 including all mouldings but excluding frames conforming to type B-0 1:2:4 using 12.5mm graded crushed stone aggregate complete all as specified and as directed by Engineer-in-Charge.

M&L For pcc type B1(1:2:4) using 20 mm graded cushed stone agg as in coping ,benching and the like incl form work complete all as specified and as directed by Engineer-in-Charge.

M&L for PCC type C1 1:3:6 using 20mm graded crushed stone aggregate as in surface channel and drain beads including all necessary form work complete all as specified and as directed by Engineer-in-Charge.

M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge.

M&L for 15mm thck rendering on fair faces of brick works in cement mortar 1:6 finished even and smooth without using extra cement in cement mortar complete all as specified and as directed by Engineer-in-Charge.

M&L for 5mm thick rendering on fair faces of concrete finished even and smooth without using extra cement in cement mortar 1:3 complete all as specified and as directed by Engineer-in-Charge.

M & L Flush pointing to brick walls in cement mortar 1:3 complete all as specified and as directed by Engineer-in-Charge.

M&L for 75mm thick PCC 1:4:8 type D2 (using 40mm graded aggregate) complete all as specified and as directed by Engineer-in-Charge.

M&L for 100 mm thick cement concrete type B-2 ,1:2:4 (20 mm graded aggregate) laid to alternate pannels and making surface even and fair complete all as Eng-in-Charge . ( Note:- Formwork is deemed to be included in quoted rates. Contractor shall not be claimed any extra cost.)

M&L for sand filling under floors, cushning under interlocking tiles or in foundations incl watering and consolidations complete all as specified and as directed.

M&L for 60 mm thick factory made coloured glossy finished inter locking cement concrete paver blocks any shape and size confirming to IS 15658-2006 of M-35 grade manufacturing by vibromechenically floated rubber molded process complete all as specified and directed by engr-in-charge(Coloured and shape of block shall be approved by Engr-in Charge)

M&L for 75mm thick PCC type C-1 1:3:6 using 20mm graded crushed stone aggregate as in plinth protection laid in alternate pannels finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L for 40 mm thick florring type, B-1 ,(1:2:4:) , using 20 mm graded crushed stone aggregate ,finished the surface even and smooth w/o using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L glass dividing strips 3mm x38mm in reqd pattern for flooring complete all as specified and as directed by Engineer-in-Charge.

M&L for 25mm thick PCC type B-0 using 20mm graded crushed stone aggregate as in sub base for laying floor finishes complete all as specified and as directed by Engineer-in-Charge.

M&L for 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and as directed by Engineer-in-Charge.

M&L for 15mm thick rendering on fair faces of brick works in cement mortar 1:4 finished rough for receiving tiles as in dado complete all as specified and as directed by Engineer-in-Charge.

M&L for 7mm thick non skid coloured ceramic tiles (area of each tile exc 0.11 and nexc 0.18 sqm) etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments complete all as specified and as directed by Engineer-in-Charge.

As per item No 61 but in vertical surfaces complete all as specified and as directed by Engineer-in-Charge.

M&L for rustic tiles with stone finish rough textures of app design set and jointed with neat cement slurry and pointed with white or coloured cement to match the shade of existing surfaces complete all as specified and as directed by Engineer-in-Charge.

M&L white marble stone slab 20mm thick as in flooring set and jointed in neat cement slury and pointed with white or colored cement complete all as specified and as directed by Engineer-in-Charge.

M&L for (350mmx250mmx7mm/450mmx350mmx 7mm thick ) coloured ceramic tiles set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments complete all as specified and as directed by Engineer-in-Charge..(Note :Contractor shall have no claim on colour or shade what so ever on this account)

Welding in repairs n. exc 2.5cm in length complete all as specified and as directed by Engineer-in-Charge.

M&L for Mild steel rolled section /tubular section as in main and cross beams , purlins , rafters ,posts where connected to common rafter and running rails etc conforming to Fe- 410-w complete all as specified and as directed by Engineer-in-Charge.

S&F 8 mm thick double wall standard polycarbonate sheets of approved colour fixed to MS frame using screw / bolts/aluminum profile and rubber packing including sealing of joints by using silicon gel complete all as specified and as directed by Engineer-in-Charge.

S&F AC board ceiling 4mm thick in 600X600mm pannel (Make-everest) designer ceiling conforming to IS 14862 type B cateogory three incl GI frame , grid work,hold fast,suspended complete.

M&L for high rib profile tile pattern color coated 0.5mm thick sheets as in roof covering and fixed as per manufacturers instruction (design as app by Engg in charge complete all as spfd )

M&L for 0.8mm thick color coated plian galvanised mild steel sheeting factory made as in ridges fixed with self driven screws complete all as specified and as directed by Engineer-in-Charge.

M&L for priming the surface with self adhesive membrane (Texa India Ltd/ Sika ) over application of primmer with a minimum of 70mm overlap (Note: primmer to be applied @ of 250gm/sqm ) including complete removal of existing treatment, complete all as specified and as directed by Engineer-in-Charge.

M&L for 10 mm thick screed bed or bedding layer in cement mortar 1:3 for finished even and fiar for receiving roof treatment icluding mixing of water proofing compound URP 301 as directed by Engr-in-Charge.

Supply only (URP -301)water proofing liquid solution complete all as specified and as directed by Engineer-in-Charge.

M&L for applying URP solution mixed with water in ratio of 1:1. as approved by Engr-in-Charge.

M & L Steel rolling shutters with 1mm thck laths , with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete; push pull or manual type complete all as specified and as directed by Engineer-in-Charge.

M&L for stainless steel as in framing for grills,gates , railing plates or other sections as per site requirement conforming to Gde 304 as spfd and directed by Eng-in Charge

Solid PVC Door Frame /guides of section of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

S&F 28 mm to 30 mm thick solid core PVC boards as in shutters to cup boards, duct covers shutters and shelves of partitions, covering etc., complete all as specified and as directed by Engineer-in-Charge.

S&F 105 x 60mm pressed steel frames for doors with one or more rebate including necessary fixing lugs, hinges lock strike plate etc complete as specified including a coat of shop coat zinc chrome primer complete all as specified and as directed by Engineer-in-Charge.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed by Engineer-in-Charge.

As per item No 81.00 above, but without glazing bars complete all as specified and as directed by Engineer-in-Charge.

S&F 200mm long mild steel tower bolt stove enamelled black with bright bolt complete all as specified and as directed by Engineer-in-Charge.

S&F 300mm mild steel sliding door bolts plate type sove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on stapple plate complete all as specified and as directed by Engineer-in-Charge.

Supply only 100mm long mild steel medium weight but hinges cold rolled complete all as specified and as directed by Engineer-in-Charge.

S&F 150mm mild steel pressed handles oval type stove enamelled black complete all as specified and as directed by Engineer-in-Charge.

S&F 35mm thick second class hard wood plain framed pannelled shutter (two panels) with lock rail and pannel or 9mm BWP comerical ply or 12mm venered particle board with comerical face venering on both faces. The size of rail and style as per IS-1003 part kilin seasoned, complete all as specified and as directed by Engineer-in-Charge.

S&F 3mm thick glass sheet oridinary qlty in steel or wooden frames complete with fixing materials such as putty glazing pins wooden beads etc, complete all as specified and as directed by Engineer-in-Charge.

S&F galvanished mild steel wire cloth .46mm nominal dia of wire and average width of apperature 1.18mm complete all as specified and as directed by Engineer-in-Charge.

S&f 110mm bore PVC (SWR) pipe single socketed , in any length with rubber joints fixed to walls complete all as specified and as directed by Engineer-in-Charge.

S&F 110mm bore PVC (SWR) bend any radius complete all as specified and as directed by Engineer-in-Charge.

M&L for 15mm bore medium grade galvanished iron water tubing with all fittings and fixed complete to walls or laid in trenches complete all as specified and as directed by Engineer-in-Charge.

M&L for 20 mm bore medium grade galvanished iron water tubing with all fittings and fixed complete to walls or laid in trenches complete all as specified and as directed by Engineer-in-Charge.

Dismantling PVC water tank exc 250 litres and n.exc 500 ltrs capaicty and removing to store.

S&F 500 ltre capacity rotational moulded polythene water storage tanks cylndrical with closed top hoisted and fixed in position all as specified,complete all as directed by Engineer-in-Charge.

S&F PVC waste coupling 32mm dia PTMT (half or full threaded ) minm wt 450 gms complete all as specified and as directed by Engineer-in-Charge.

S&F PVC waste pipe 32mm bore with cup and washers complete all as specified and as directed by Engineer-in-Charge.

S&F 15mm bore bib taps cast copper alloy with capstan head chromium plated screwed down screwed for iron pipe or brass ferrule complete all as specified and as directed by Engineer-in-Charge.

S&F 15mm bore pillar tap cast copper alloy with capstan head chromium plated screwed down under high pressure with or without lettered hot or cold with long shank and fly nuts screwed for iron pipe complete all as specified and as directed by Engineer-in-Charge.

S&F 15mm bore stop cock chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule complete all as specified and as directed by Engineer-in-Charge.

S&F 15mm bore brass valve high pressure with polythene float and fly nuts complete screwed for iron pipe or brass ferrule complete all as specified and as directed by Engineer-in-Charge.

S&F shelf of PTMT with and including chromium plated brass screws and wooden or plastic cleats complete all as specified and as directed by Engineer-in-Charge.

S&F 15mm bore 450 mm long PVC connection with PTMT nutscomplete all as specified and as directed by Engineer-in-Charge.

S&F 75mm bore cast iron floor trap with grating including jointing to waster pipe fixed in cement concrete type B-1 1:2:4, complete all as specified and as directed by Engineer-in-Charge.

S&F 75mm bore sand cast iron waste pipe any length with or without ears laid in floor complete all as specified and as directed by Engineer-in-Charge.

S&F viterous China squatting pan or Orissa patter 580 x 440 mm white with integral foot rest (excluding cistern) as in repairs, complete all as specified and as directed by Engineer-in-Charge.

S&F sand cast iron 'P' or S trap 100mm bore for ind type w/c,complete all as specified and as directed by Engineer-in-Charge.

S&F viterous China urinal half stall type white including CP spreader, waster pipe etc, complete all as specified and as directed by Engineer-in-Charge.

S&F PVC flushing cistern 10 ltrs capacity with complete in let ball valve complete all as specified and as directed by Engineer-in-Charge..(Make Perryware/CERA)

S&F viterous china wash hand basin flat back size 580x450mm excluding traps, waste , chain , plug and porcelain stopper incl brackets complete all as specified and as directed by Engineer-in-Charge.

Grubbing out tree trunk nexc 30 cm girth of tree including cutting of of trunk portion protruding over ground ,incl cutting out walls of building , plinth protection / walls / slabs etc (any type of trees peeple or any other ) stacking servicable material and removing of unservicable material to a distance nexc 50 m and clearing site. (Note : Holes cut out to remove roots shall be repaired and matching the same )

Labour only for prooning off tree roots form walls , roofs etc irrespective of any heights and repairing the same after removal of vegitation complete all as specified and as directed by Engineer-in-Charge.

M&L for two coats of oil bound distamper on new surfaces treared with POP over a coat of primmer including preparation of surfaces complete all as specified and as directed by Engineer-in-Charge.

M&L for one coats of oil bound distamper on new surfaces treared with POP over a coat of primmer including preparation of surfaces complete all as specified and as directed by Engineer-in-Charge..

M&L for two coats of synthetic enamel paint on new steel surfaces inclduing preparation.

M&L for two coats of synthetic enamel paint on new steel surfaces including preparation over a coat of red oxide Zinc chrome primer.

M&L for one coats of synthetic enamel paint on new steel surfaces including preparation over a coat of red oxide Zinc chrome primer complete all as specified and as directed by Engineer-in-Charge.

M&L for two coats of synthetic enamel paint on new wooden surfaces incl prep over a coat of pink primmer complete all as specified and as directed by Engineer-in-Charge.

M&L for one coats of synthetic enamel paint on new wooden surfaces incl prep over a coat of pink primmer complete all as specified and as directed by Engineer-in-Charge.

M&L for two coats cement base paint on newly plastered surfaces including preparation of surfaces, complete all as specified and as directed by Engineer-in-Charge.

As per item No 120 but one coat on old decorated surfaces, complete all as specified and as directed by Engineer-in-Charge.

M&L for three coats of white wash on newly plastered surfaces including preparation of surfaces, complete all as specified and as directed by Engineer-in-Charge.

As per item No 122 but one coat on old decorated surfaces, complete all as specified and as directed by Engineer-in-Charge.

M&L for two coats of white wash on newly ceiling plastered surfaces including preparation of surfaces, complete all as specified and as directed by Engineer-in-Charge.

As per item No 124 but one coat on old decorated surfaces, complete all as specified and as directed by Engineer-in-Charge.

M&L for one coat of weather proof exterior emulsion paint on old surfaces incl prep complete all as specified and as directed by Engineer-in-Charge.

M&L applying two coats pidifin coat including mixing of liquid agent and dry powder . (Pidifin 2K no 112 ) on wall in any position such as UG sump( Dr Fixit /Sikka) ,complete all as specified and as directed by Engineer-in-Charge.(Note : Scaffolding reqd at site by contractor shall be deemed to be included in Quoted rates)

Demolition of spalling concrete from soffits of slab to any thickness in controlled manner incl cleaning of reinforcement as directed and approved by Eng-in-Charge.

Apply one coat of “Dr Fixit Rust Remover” (Rust removing chemical) or “Defroster” or equivalent chemical as approved to old rusted reinforcement after necessary preparation of surfaces by brush application with out any deduction of mesh slots complete all as specified and as directed by Engineer-in-Charge.

Supply and fix hard drawn steel wire fabric cut to length bent to shape, fabric 3 mm dia, 50 mm mesh cover entire steel surface , complete all as specified and as directed by Engineer-in-Charge.

Bonding the entire exposed surface with one coat of “Fosroc Ntobond SBR” as per manufacture instruction , complete all as specified and as directed by Engineer-in-Charge.

Apply one layer of Fosroc spray ser SL concrete 20 mm to 25 mm thick (comprises composition 1:2:1 plain cement concrete i.e. one part of cement two parts of fine aggregate and one part of 10 mm and down size trap stone aggregate) mixed with spray set SL 2 to 2.5% weight of cement and 12.5 to 16.5 liters of water mixed as per manufacture instructions and gunniting pressure nozzle with a delivery capacity of 2.5 kg per sq m over column, beam, roof slab and other similar work , complete all as specified and as directed by Engineer-in-Charge.(Note Contractor shall provide the even surface duly floated and clearence from wall floor or site damaged due to splashing of cement grouts)

Excavating in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation etc or for laying of cables, pipes etc and getting out in soft/loose soil completed all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick in soft/loose soil completed all as specified and directed by Engineer-in-Charge

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point completed all as specified and directed by Engineer-in-Charge.

M&L for Rendering 10mm thick cement plaster on fair faces of brick or conc. Surfaces in cement mortar 1:4,even and smooth w/o using extra cement complete all as specified and as directed by Engineer-in-Charge.

M & L for repairing/replacing RCC collar for jointing RCC pipe up to 600 mm dia with spun yarn and epoxy as approved so as to make leak proof the same as directed. Any other damage to side wall of jack well and flocculator shall be repared with out any extra cost to govt complete all as specified and as directed by Engineer-in-Charge.

M & L Formwork to sides and soofits of beam rough finished surfaces of flat concrete surfaces complete all as specified and as directed by Engineer-in-Charge.

M&L for TMT steel bars 10mm dia and over cut to length bent to shape reqd incl cranking bending spirally for hooping for columns hooking ends and binding with mild steel wire annealed not less than 0.9mm dia or securing with clips, complete all as specified and as directed by Engineer-in-Charge.

Ditto as above SI No 139.00 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed by Engineer-in-Charge.

M&L for reinforced cement concrete M-20 (nominal mix 1:2:4 type B-1) using 20mm graded crush stone as in beam/band etc, complete all as specified and as directed by Engineer-in-Charge.

M&L for reinforced cement concrete M-20 (nominal mix 1:2:4 type B-1) using 20mm graded crush stone as in Chajjas etc, complete all as specified and as directed by Engineer-in-Charge.

M & L Formwork to chullah hoods, chajjas, throughs and similar items including edges complete all as specified and as directed by Engineer-in-Charge.

Greasing and oiling of old steel rolling shutters of any size and description by any mean and making usable and smooth functioning, including taking down of hood rolling spring if required complete all as specified and as directed by Engineer-in-Charge.

Taking down carefully existing unserviceable Copper/aluminum batten/surface conduit/concealed conduit point wiring (light, fan, bell/buzzer, socket or power) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, pendents, sockets, lamp holders, shades, fan regulators, light fittings, bells etc (including old MS sunken boxes) and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and as directed by the Engr-in-Charge.

Taking down of unserviceable DBs/switch fuses/changeover in sheet steel enclosure complete with MCBs/Fuse/grips any capacity and removing from site and making good disturbed surface of wall, floor etc. Taking after disconnecting all cable complete all as specified and as directed by the Engr-in-Charge.

Point wiring with stranded copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 1.5 Sq mm single core in and including new non-metallic rigid surface PVC conduit, not less than 20 mm dia, medium duty ISI marked, including conduit fittings such as tees, bends etc terminating in and including new sunken box covered with and including 3 mm thick bakelite laminated sheet top cover of approved make for one fan or light or exhaust fan or bell/buzzer point controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed copper conductor cable, multi stranded as earth wire to common earth & connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per item No 147.00 here-in-before but socket point on the same board with other switches complete as specifed as directed by Engineer - In - Charge .

All as per item No 147.00 here-in-before but socket point on the independent board with other switches complete as specifed as directed by Engineer - In - Charge .

All as per item No 147.00 here-in-before but cable of 2.5 Sq mm for 15 Amp switch socket outlet on independent board

S&F Switch piano flush type, Single pole 5 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge

S&F Ceiling rose PVC/poly carbonate insulated body three terminal ISI marked, complete all as specified and as directed by Engineer-in-Charge.

S&F Socket outlet flush type, 3 pin, 5 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge.

S&F Switch piano flush type, Single pole 15 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge .

S&F Socket outlet flush type, 3 pin, 15 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge.

S&F Lamp holder insulated body with back plate for conduit/casing capping fittings with LED Bulb 9W complete all as specified and as directed by Engineer-in-Charge.

Ceiling fan regulator electronic type, 230 Volt, 150 Watt with 5 step of control including making holes in laminated bakelite sheet cover and connection complete all as specified and as directed by Engineer-in-Charge.

S&F Decorative ultra slim linear LED lightening fixture, energy efficent 18/20 Watt complete all as specified and directed by Engineer-in-charge.Make Surya /Phillips/wipro/CG /Bajaj

Suppy and Fixing LED based security light, housing made up of LM6 pressure die cast aluminium alloy with effective thermal management, sturdiness. The fixture should have a minimum system efficiency of more than 100 lumen/watt and a minimum system lumen output of not less than 2500 lumens and maximum system wattage 25 Watts. The fixture shall have a correlated colour temperature of al least 5700K and CRI f minimum 70. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance ingress protection of IP66 (lamp and gear compartment and mechanical inpact resistance raiting of IK>=08. The fixture driver should have an operating voltage range of 140-270 V & potted type for humming free operation, driver should be withstand up to 440v for 8hrs, two surge proection not less than 5KV one on driver and one external surge protection, PF>0.95 and THD<10% and have double phase protection. LED light fitting should be suitable for ambient temperature from (-) 10C to (+) 50 C. The fixture should comply with the parameters IEC 60598 and LED should comply to IEC 61000-3-2 ed. 3.2 per harmonics IEC 61347-2-3,2006 in configuration with IEC 61347-1 ed 2.0,2007 for electrical safety LM 79 and for LED LM 80 test report needs to be submitted from the house NABL accreditation laboratory. Make CG/C&S/Bajaj/Havells

S&F in replacement Sheet metal enclosure for distribution boards, suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 8 ways double door , supplied and fixed in repair, including making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement sheet metal enclosure for distribution boards, suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 4 ways double door , supplied and fixed in repair, including making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement MCB single pole, 240 volts of rating 6-32 Amps, breaking capacity of 10 KA complete all as specified and as directed by Engineer-in-Charge .

S&F in replacement MCB suitable for 6 to 32 Amps, 240 Volt AC supply single pole and neutral with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge.

Taking down old sub main wiring and providing new sub main wiring with 2 single core, multi-stranded PVC insulated cable unsheathed 1100 volts grade with copper conductor of size 4 sq mm drawn in and including PVC concealed including earth continuity conductor cable of size 4 sq mm PVC insulated unsheathed copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by mean of GI wire 4 mm dia by means of bolts, nuts check nuts and washers of GI or steel and connecting to earthing test point, main switch board, testing on completion including GI pipe 20 mm dia light grade for watering and bringing the same upto 30 cm above normal ground level with plug at top including pipe fittings etc complete and GI pipe 15 mm dia light grade for the protection of GI wire from earth pit to earth point complete including necessary excavation and earth work in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance n.exc 50 m all as specified as shown in electrical plate No 3 SSR Part-I.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed by Engineer-in-Charge.

Hanging only ceiling fan as taking down vide item Ser No 163.00 and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed by Engineer-in-Charge.

GS BUILDERS AND ENGINEERS

Satish kumar and company