Construction of Sub Health centre building at Kadayal Area in Kadayal Town Panchayat, 15th SFC 2022-23 Health Grant, Kanyakumari District

Amount

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling stone dust in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Refilling the basement with excavated earth other than sand complying the standard specification

Cement Concrete 1:4:8 (One Cement, Four sand and Eieght hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Brick work in Cement Mortar 1:5 using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specification. below basement

above basement

Brick partition walls in Cement Mortar 1:3 using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specification. Partition walls

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting us below ground level

Plain and surface

Reinforced Cement Concrete 1:11/2:3(One Cement, One and a half sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three Sand) etc., complete complying with standard specification and as directed by the departmental officers. below basement

basement To ground floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the departmental officers.

Finishing with one course of pressed tiles of size 23x23x2cm with cm 1:3 pointed with same mortar

Flooring with Vitrified tiles size 600x600x8mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / m². etc., complete complying with standard specification.

Providing granolithic floor finish in cement concrete 1:2:4 mix using 10-12mm ISS metal to 25mm thick including cost and conveyance of all materials to site and all labour charges for mixing, laying, curing etc complete for 10 cum

Paving the flooring with special type of flooring tiles (Cement based Hydraulically pressed Anti skid tiles (20mm thick) in CM 1:3, 20mm thick

Dadooing walls with best approved quality, colour glazed tiles of 150mm x 150mm x 6mm size set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / m². neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes of 110mm dia., having a pressure of 4 kg. / sq.cm including cost of necessary PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of Paris putty, wherever required etc., complete complying with standard specification. Inner + ceiling

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of Paris putty, wherever required etc., complete complying with standard specification. Outer

Painting new iron works such as steel doors, windows,ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing of door shutter using MDF board of exterior grade both sides prelaminated of 35mm thick

Solid PVC Door Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm.The over all size of frames shall be 50mm

Supplying and fixing of steel window with frame (two leaves) of size 1.20 x 1.30 m and cost including welding and conveyance of all materials to site, locking arrangements and painting one coat of primer etc complete.

Fabrication, Supply and fixing in position of 'N' type ventilators using M.S. angle of size 25 x 25 x 5 mm for frame and MS flat of size 20 x 3 mm for fixing the weld mesh and using 25 x 22 x 3 mm 'T' section for frame glass. Special type of Hold fast welded to the frame of 45 degree inclined towards centre for wall and fixing the weldmesh 75 x 25 mm 10 gauge including cost of 3 mm thick pinheaded glass panes for all panels and fixing the glass panels with necessary clips & putties with required bolts, nuts and washers and one coat of red oxide primer etc including necessary dismantling, making holes in RCC columns, beams, masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by the departmental officers.

Supply and fixing in position best quality of approved make Indian Water closet of size 580 x 440 mm with all accessories such as 'P' trap or 'S' trap confirming to IS 2556 part XII with sand cusion and forming flooring alround the closet using 40 mm leveling course 1:4:8 - 100 mm thick and finishing the top to the required slope and including necessary internal connection and outlet connection and making the disturbed potion to original condition without leakage etc including Labour charges for fixing etc complete.

Supplying and fixing in position of glazed water closet of size 58 cm with ‘P’ trap; and double flopped seat cover, 12.5 litres capacity PVC low level automatic flushing tank including all internal plated brown headed stopcock, 12 mm nylon connection with necessary teak wood plugs, clamps screws to the portion of coming with wall or floors, including dismantling masonry and redoing the same to the original condition.

Supply and fixing in position best quality of approved make Wash hand basin of size 550 x 440 mm with all accessories such as cast iron brackets, including cost of 15 mm Ø brass nipple, 15 mm nylon connection etc including fixing the wash basin in the wall in position with a pair of CI brackets with TW plug and screws and giving necessary water supply connection and painting the brackets with two coats of paint over priming coat of anticorrosive paint including testing leakages etc, complete complying with standard specifications (the wash hand basin and the specials should be got approved by Departmental officer before use on works)

Supply and delivery of fixing of HDPE tank 2000 litres capacity as per IS 12701/1996 including loading, unloading, transportation and labour charges for fixing of GI pipes and specials for pipe connection works including cutting, threading and fixing chargers as directed by officers.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A FT switch and making good of the concealed portion with suitable colour for PVC concealed light / fan Point

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A FT switch and making good of the concealed portion with suitable colour for PVC concealed light (6 points per coil) (for rooms like bath, toilet & pumproom, etc.)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm TW switch box with 3mm thick hylem sheet cover for 5A 3 pin non inter locking wall socket with 5A flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point

Wiring with 2 x 4 sq.mm. (56 / 0.3) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm TW switch box with 3mm thick hylem sheet for 15A 3 pin non inter locking wall socket with 15A flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed power plug point

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall

4' 18W Crystal Glass LED Tube Light Fitting

Supply and fixing of TNEB Meter Board suitable for 3 Phase, 63A service connection made up of suitable angle iron frame work of size 2 feet x 1½ feet using angle iron of size 1½ inch x 1½ inch x ¼ inch rigidly fixed on wall, covered with hylem sheet of size 2 feet x 1½ feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units (500V), 1 No. Neutral link, copper earth flat of size 1inch x ¼ inch with interconnection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete.

Supply and run of 2 of 6 sq.mm. (84 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V on 7 / 20 GI bearer wire for service connection mains

Supply and run of 1 of No.8 SWG GI wire for earth connection

Supply and fixing of 32 Amps DP Switch of 500 V with Metal clad with fuse and neutral (Side Handle) on suitable TW Board , with earth connection only

Supply and fixing of 9W LED bulb fitting for BH point. SD80

JAYASINGH.P (BID ID -1072196)