Construction of Gram Panchayat Community Centre Panchayat Ghar at Salgran Development Block Keylong Sub Block Udaipur Distt. Lahul Spiti Himachal Pradesh Sub Head Civil work in First Floor Water Supply and Sanitary Installations etc

Amount

Reinforced cement concrete work in walls any thickness including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor all level excluding the cost of centering, shuttering, finishing and reinforcement in secified grade of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed, vibrated and curing complete as required including carriage of materials with in all leads, lifts and other incidentals or as per the direction and to the entire satisfaction of Engineer-in-Charge.

Reinforced cement concrete work in Beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor all levels excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed, vibrated and curing complete including carriage of materials with in all leads, lifts and other incidentals or as per the direction and to the entire satisfaction of Engineer-in-Charge.

Providing form work with steel plates 3.15 mm ( three point fifteen millimetre ) thick welded with angle iron in frame 30x30x5 mm (Thirty millimetre x Thirty millimetre x five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in-charge in:-

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, pillars, posts and struts square, rectangular or polygonal in plan as required.

Edges of slab and breaks in floor and walls under 20 cm wide as required.

Cornices and mouldings

Providing tor steel reinforcement TMT bars of grade Fe-500 D or more ISI make high yield strength for reinforced cement concrete work including straightening, cutting ,bending, binding and placing in position and cost of binding wire complete up to floor all levels including carriage of material with in all leads, lifts and other incidentals complete as per direction and to the entire satisfaction of Engineer-in-Charge

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes in cement mortar 1:6 (one cement : six sand) including curing complete and carriage of material with in all leads, lifts and other incidentals, complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in cement mortar 1:4 (one cement : four sand) including curing complete and carriage of material with in all leads, lifts and other incidentals, complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) complete including carriage of materials with in all leads, lifts and other incidentals.

Providing second class deodar wood work in frames of doors, windows, clerestory, windows and other frames wrought, framed and fixed in position, as required including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick complete including carriage of materials with in all leads, lifts and other incidentals.

5 mm thick glass pans (weight not less then 12.5 kg/sqm)

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4 mm wide aperture with matching wood beading

Providing and fixing ISI marked flush door shutters 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws etc. conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including carriage of materials with in all leads, lifts and other incidentals.

Providing extra for lipping with 2nd class teak wood battens 25 mm (twenty-five milimetre) minimum depth on all edges of flush door shutters (over all area of door shutter to be measured)complete including carriage of materials with in all leads, lifts and other incidentals.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing bright finished stainless steel sliding door bolts, ISI marked with nuts, bolts & screws complete with in all leads, lifts and other incidentals.

300 x 16 mm (three hundred X sixteen mili metres)

200 x 16 mm (two hundred X sixteen mili metres)

Providing and fixing bright finished stainless steel tower bolts, ISI marked with screws complete with in all leads, lifts and other incidentals.

200 x 10 mm (two hundred X ten mili metres)

150 x 10 mm (one hundred fifty X ten mili metres)

Providing and fixing 50 cm long Stainless Steel kicking plate of size 100x3.15 mm, to required colour or shade, with necessary screws etc. complete with in all leads, lifts and other incidentals.

Providing and fixing stainless steel handles, ISI marked with screws complete with in all leads, lifts and other incidentals.

200 mm (two hundred milimeter)

150 mm (one hundred fifty milimeter)

Providing and fixing twin rubber stopper Stainless Steel hanging floor door stopper, ISI marked, with necessary screws etc. complete. with in all leads, lifts and other incidentals.

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. all complete as specified as directed by the Engineer-in-Charge. including carriage of materials with in all leads, lifts and other incidentals.

Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

Casement window double panels with S.S. friction hinges (300 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window above 0.75 sqm upto 1.50 sqm).

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section madefrom roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. all complete as specified as directed by the Engineer-in-Charge. including carriage of materials with in all leads, lifts and other incidentals.

Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Structural Steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer as required including carriage of materials with in all leads, lifts and other incidentals as per direction by the Engineer-in-Charge.

Providing and fixing stainless steel ( Grade 304) railing, grills made of Hollow/solid tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). as required including carriage of materials with in all leads, lifts and other incidentals complete as per direction by the Engineer-in-Charge.

Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying vitrified floor tiles 600 mm x 600 mm x 10 mm with water absorption less than 0.08 % and conforming to IS: 15622, of approved make Kajaria/Nitco/Jonson tiles in all colours and shades, laid on 20 mm thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. complete including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying Vitrified tiles 600 mm x 600 mm x 10 mm with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make Kajaria/Nitco/Jonson tiles in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (one cement : three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 0.60 mm ( zero point sixty milimeters) thick prepainted steel sheet in roofing with hot dipped metallic zink coated sheet with top coat of regular modified polyster ( RNP ) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted screws complete with all accesoriees as per the directon of engineer in charge including carriage of material with in all leads, lifts and other incidentals.

Providing and fixing ridges or hips 60 cm over all with 0.60 mm ( zero point sixty milimeters) thick prepainted steel sheet in roofing with hot dipped metallic zink coated sheet with top coat of regular modified polyster ( RNP ) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted screws complete with all accesoriees as required as per the directon of engineer in charge including carriage of material with in all leads lifts in all floors.

Providing and fixing valley 60 cm over all 0.60 mm ( zero point sixty milimeters) thick prepainted steel sheet in roofing with hot dipped metallic zink coated sheet with top coat of regular modified polyster ( RNP ) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted screws /J or L hooks, bolts and nuts 6 mm dia withprepainted GI limpet and bitumen washers complete with all accessories including carriage of material with in all leads lifts in all floors as required as per the directon of engineer in charge.

Providing and fixing M.S BP sheet 1.66 mm to 2 mm thick in eaves board / facia / soffit / ceiling including cutting fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instructions of engineer in charge ( base members of steel work shall be measured and paid separtely including carriage of material with in all leads lifts in all floors as required as per the direction of Engineer-in-charge.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Gutter (600 mm over all girth) complete as per the directon of engineer in charge including carriage of material with in all leads lifts and other incidentals.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge including carriage of material with in all leads lifts and other incidentals.

12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

Providing and fixing Single socketed pipes 110 mm dia (one hundred ten mili metre) with minimum pressure of 4.5 kg/sqm on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories of working pressure 4 Kgf/sq cm for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion including carriage of material in all leads & lifts and other incidentals.

110 mm bend (one hundred ten mili metres)

110 mm shoe (one hundred ten mili metres)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm (fifty X fifty X fifty mili metres) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (one cement : four coarse sand) and making good the wall etc. complete. including carriage of material with in all leads, lifts and other incidentals.

110 mm diameter (one hundred ten mili metres)

15 mm (fifteen millimeter) thick cement plaster in single coat on rough / fair side of brick /concrete / stone wall for interior plastering for all floors including arises internal rounded angles chafers and / or rounded angles chamfers and / or rounded angles not exceeding 80 mm (eighty millimeters )In girth and finished even and smooth in cement mortar 1:6 (one cement : six sand ) including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

20 mm (twenty millimeter) thick cement plaster in single coat on rough / fair side of brick /concrete/stone wall for interior plastering for all floors including arises internal rounded angles chafers and / or rounded angles chamfers and/ or rounded angles not exceeding 80mm (eighty millimeters )In girth and finished even and smooth in cement mortar 1:4 (one cement :four sand )as per direction of engineer in charge including carriage of material within all leads lifts in all floors and other incidental.

18 mm thick and 7.5 cm wide plain cement mortar band in cement mortar 1:4 (1 cement : 4 fine sand) including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the top layer of washed stone grit or plain plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and applying white cement based putty of average thickness 1 mm (one milimeter), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Distempering two coats with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 (fifty) grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of WC ,kitchen and the like consisting of (i) 1st course of applying cement slurry @4.40kg mixed with water proofing compound confirming to IS 2645 in recommended proportions including rounding of junctions of vertical and horizontal surfaces (ii) 2nd course of 20mm cement plaster 1:3(one cement:three sand) mixed with water proofing compound in recommended proportions including rounding of junctions of vertical and horizontal surfaces (iii) 3rd course of applying blown or residual bitumen applied hot at 1.7kg/sqm of area (iv) 4th course of 400 micron thick PVC sheet(overlaps at joints of PVC sheets shouldbe 100 mm wide and pasted to each other with bitumen at 1.7 kg/sqm) including carriage of material with ileads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) cera/hindware/parryware make with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing White Vitreous China Wash basin cera/hindware/parryware make size 550 x 400 mm (five hundred fifty X four hundred mili meters) with a pair of 15 mm C.P. brass pillar taps wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require including carriage of material with in all leads, lifts and other incidentals.

Providing and fixing white vitreous china pedestal for wash basin cera/hindware/parryware make completely recessed at the back for the reception of pipes and fittings as required including carriage of material with in all leads, lifts and other incidentals .

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. The sample of heavy duty jet should be got approved from Engineer - in - charge before use including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 32 mm dia P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 100 mm stainless steel grating heavy duty for gully trap. complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 600 x 450 mm beveled edge mirror of heavy dutysuperior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 600 x 120 x 5 mm heavy duty of approved quality glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing CP brass heavy duty toilet paper holder complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 15 mm nominal bore C.P. brass bib cock of jaquar/jal/ess ess make of approved quality conforming to IS:8931 : The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of jaquar/jal/ess ess make of approved quality conforming to IS standareds and weighing not less than 810 gms. The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and fixing 15 mm nominal bore C.P. brass long body bib cock of jaquar/jal/ess ess make of approved quality conforming to IS standareds and weighing not less than 690 gms. The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 15 mm nominal bore of jaquar/jal/ess ess make. The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore of jaquar/jal/ess ess make. The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.The sample quality & series should be got approved from Engineer - in - charge before use including carriage of material with in all leads, lifts and other incidentals.

Providing and fixing 110 mm x 75 mm PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive cost of cutting and making good the walls and floors complete.

Single equal branch of required with oval access door insertion rubber washer 3mm thick bolts and nuts. "PVC Door Tee"

75 mm dia.

110 mm dia.

Providing and fixing sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete. "PVC Door Bend"

75 mm dia.

110 mm dia.

Providing and fixing sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete. "PVC Collar"

75 mm dia.

110 mm dia.

Providing and fixing PVC Poly plast sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme / centimeter metre square) fitting & accessories including filling the joints with approved adhesive complete. "PVC Plain Bend"

75 mm dia.

110 mm dia.

Providing and fixing sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete. "PVC Plain Tee"

75 mm dia.

110 mm dia.

Providing and fixing sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete. "PVC Cowel"

75 mm dia.

110 mm dia.

Providing and fixing sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete. "PVC Offset"

75 mm dia.

110 mm dia.

Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixd to wooden cleats with C.P. Brass screws complete including carriage of material with in all leads, lifts and other incidentals.

Providing and fixing C.P. Brass towel rail of size 600 mm x 20 mm complete with C.P. Brass brackets fixed to wooden plugs with CP brass screws complete including carriage of material with all leads and lifts.

Shanoo Sharma Contractor (BID ID -520468)