Renovation and Furnishing of Existing Water Quality Lab Level-2, Aurangabad. (Hydrology Project Sub Division, Aurangabad) (Second Call)

Amount

Providing and laying Vitrified mirror/glossy finish having decorative type of size 590 millimeter to 605 millimeter x 590 millimeter to 605 millimeter of 8 to 10 millimeter thickness (on a existing flooring) with bonding chemical and confirming to IS15622-2006 (Group Bla) of approved make shade and pattern for flooring in required position laid on a bed of bonding chemical filling joints curing and cleaning etc complete.

Providing and preparing kitchen otta up to 75 cm width,made up from 30 mm thick and 75 cm high vertical support for kadppa at 1 m. c/c of 25 mm thick both side polished kadappa middle shelf and bottom of 20 mm thick one side polished kadappa with facia patti of 20 x 50 mm kadappa including all material labour cutting fixing with cement mortar and araldite curing polished and cleaning etc. complete.

Providing and fixing shutter to wall cupboard made from 19 mm thick Teak particle board with approved coloured laminated face 1.5 mm thick bonded with phenol formaldehyde synthetic resin B.W.P. grade including lipping beading iron oxidised fixtures and fastening and oil primer coat etc. complete. (Excluding cupboard frame).

Providing and fixing partitions with 12 mm thick three layerd flat pressed teakwood commercial board compressed one face and other teak veneer bonded with phenol formaldehyde synthetic resin including CTW vertical 70 x 70 mm and top and bottom rail of 70 x 35 mm and covering batten of 20 x 10 mm at 1.00 metre apart on both ways or as directed including finishing with one coat of primer complete.

Providing antitermite treatment to the sides of flooring of the existing building as per I.S. 6313 (Part-III) by punching holes 6mm dia. drilled at a distance of 30cm. centre to centre and injecting one percent of chlorodane emulsion concentrate at the rate of 50 ml per hole and sealing by filling putty etc. complete covering 2 years guarantee on bond paper.

Providing general pest control services to the building to control the nuisance of cockroaches, lizards, pin bores and other insects etc. with 4 operations in a year and monthly check up.

Providing antitermite treatment to the wooden frames of doors/windows of the existing building as per I.S. 6313 (Part-III) by drilling 6mm dia. holes at four corners on one side and four corners on other side at a downward angle of about 45 degree at the junction of wood work and masonary and injecting 150 ml. of chlorodane 5% W.C. and sealing by filling putty etc. complete covering 2 years guarantee on bond paper.

Providing and fixing in position extruded aluminium partitions having frame made out of extruded tubular section of size 65 mm x 40 mm with 12 mm thick three layered flat pressed teak wood particle board bonded with BWP type exterior grade phenol formaldehyde synthetic resin conforming to IS 129231990, laminated on both sides, Novateak or equivalent with aluminium glazing clips of size 12 mm x 12 mm (conical) as per drawing etc. complete.

Providing and fixing in position, Single shuttered aluminium extruded powder coated openable door of overall size 0.90 m x 2.40 m with aluminium door frame of powder coated section 101.60 x 44.75mm , 3.18 mm thick and shutter comprising of powder coated section having bottom and lock rail of size 150 mm x 44.5 mm x 3.00 mm thick top rails 47.62 x 44.45 mm x 3.00 mm thick , vertical style 47.62 x 44.45 mm, 3.00 mm thick and for shutter plain glass panes 5 mm thick for top panels and 12mm thick both side laminated phenol bonded particle board panels for bottom panels etc. , I.S.I. mark , with bijagiri having heavy duty concealed lock, necessary beading, glazing clips, PVC gaskets, 250mm length tower bolts, 150mm diam. pad handle, etc. as per detailed design and drawing or as directed by engineer in charge including all materials , labours, and equipment etc. complete

Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 kg/Rmt. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 kg/Rmt.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section 40 x 18 x 1.25 mm at weight o.417 kg/Rmt. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour Anodising with box

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete.

Providing and laying in trenches 15 mm dia. medium grade having embossed as ISI Mark galvanised iron pipes of 1.25 kg/meter necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. 15mm dia

Providing and laying in trenches 20 mm dia. medium grade having embossed as ISI Mark galvanised iron pipes of 1.63 kg/meter necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. 20mm dia

Providing and laying in trenches 25 mm dia. medium grade having embossed as ISI Mark galvanised iron pipes of 2.49 kg/meter necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. 25mm dia

Providing and laying in trenches 40 mm dia. medium grade having embossed as ISI Mark galvanised iron pipes of 3.68 kg/meter necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. 40mm dia

Providing and fixing stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. 75 mm dia

Providing and fixing stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete . 110mm dia

Providing and fixing white glazed earthenware lipped flat back/corner type Urinal with PVC 5 liters flushing cistern with fittings, inlet pipe with stop tap, brackets for fixing the cistern, 32 mm diameter P.V.C. flush pipe with fitting including lead soil pipe, lead trap and soil pipe connection up to the outside face of wall.

Providing and fixing 15 mm diameter PVC Aqua kraft type Supreme make or equivalent make super Two Way bib tap with flange and extender including all accessories etc complete

Providing and fixing stainless steel sink of size 600 x 510 x 200 mm incluidng coupling, outlet pipe, elbow and other necessary fitting, finishing etc. complete.

Providing and fixing 10cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete.

Providing and fixing 40 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirements etc. complete.

Providing and applying priming coat on concrete/ masonry/ Abestos cement/plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required As directed by Engineer in charge.

Providing and applying plastic emulsion paint of approved quality, colour and shade to old and new surface in three coats including scaffolding, preparing the surface. ( excluding prime coat) complete.

Providing and applying washable oil-bound distemper of approved colour and shade to old and new surfaces in three coats includidng scaffolding, preparidng the surfaces. ( excluding the primer coat) complete.

Providing and applying two coats of synthetic enamel paint of approved colour to new /old structural steel work and wood work in buildings, includidng scaffolding if necessary, cleaning and preparing the surface ( excludidng primer coat) complete.

Part –II Electrical Work

Point wiring in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FR grade copper wire, Modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter ISI mark approved make duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 6A / 10A ISI mark approved make duly erected on provided plate and box with wiring connections complete.

Point wiring for independent plug in PVC trunking (casingcapping) with 1.5 sq.m (2+1E) FR grade copper wire with Modular switch and required accessories as per specification No: WG-PW/SW

Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter ISI mark approved make duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch one way 16 / 20 A, ISI mark, approved make duly erected on provided plate and box with wiring connections complete with neon indicator.

Supplying and erectingPVC Surface modular switch boxwith double mounting plate for 12 moduleduly erected in an approved manner.

Supplying and erectingPVC Surface modular switch boxwith double mounting plate for 6 moduleduly erected in an approved manner.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 3 module duly erected in an approved manner

Supplying and erecting ISI mark modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete. Note: Add Rs 57/- for additional two module box with double mounting plate if required.

Supplying & erecting mains with 3x6 sq.mm F.R copper PVC insulated wirelaid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying & erecting mains with 3x4 sq.mm F.R copper PVC insulated wirelaid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No:WG-MA/BW

Supplying & erecting mains with 2x2.5 sq.mm F.R copper PVC insulated wirelaid in provided conduit/trunking/inside pole/Bus bars or any other places. As per specification No: WG-MA/BW

Supplying & erecting mains with 1x2.5 sq.mm F.R copper PVC insulated wirelaid in provided conduit/trunking/inside pole/Bus bars or any other places. As per specification No: WG-MA/BW

Supplying & erecting mains with2x1.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erectingPVC trunking (PVC casing-ncapping of size 32 mm with accessories on wall/ceiling as per specification No: WG-MA/CON, para no. 1.1.2

Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification No. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, C-series (for motor/power) in provided distribution board as per specification No. SW-SWR/MCB

Supplying, erecting & marking DPMCB 40A to 63A, B - series (for lighting) in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking DPMCB 40A to 63A, C series (for motor/power) in provided distribution board as per specification No.SW-SWR/MCB

Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/ flush mounted with 2 ways for incoming and 10 ways for outgoing SP MCB’s on iron/ G.I. frame/wooden board as per specification No. SWSWR/ MCBDB

Supplying and erecting single pole and neutral distribution board (SPNDB) with doorsurface/flush mounted with 2 ways for incoming and 6 ways for outgoing SP MCB’s on iron/ G.I. frame/wooden board as per specification No. SWSWR/ MCBDB

Supplying and erecting regular/ standard model Ceiling fan of 1400 mm. sweep complete erected in position as per specification no. FG-FN/CF

Supplying & fixing Anchor type fastener Fan hook, with 2 Nos of 10mm dia x 75 mm long with necessary materials for Ceiling Fan.

Supplying and erecting modular type blanking plate one module ISI mark approved make duly erected on provided plate & box.

Supplying and erecting Electronic Type cordless call bell erected on T.W. board having portable bell push working on 9V. D.C.battery and (Effective range upto 45 meter) bell on 250 V A.C. supply.

Supplying & erecting T8 LED 20W tube light fitting (4 feet)with aluminium housing, heat sink, integrated HF electronic driver complete( including lamp).

Dismantling the existing light, fan, bell, clock, independent plugpoint, wiring including circuit mains of all types along with accessories etc.complete as per specification No:WG-DM/PW

Dismantling of existing fluorescent fittings of any type & size.

Supplying and erecting Exhaust fan heavy duty 230 V A.C. 50 cycles 375/380 mm. 1400 RPM complete erected in position as perspecifcation no. FG-FN/EXF

Providing earthing with Copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification No.EA-EP

rudra construction