SPECIAL REPAIR WORK IN MD ACCN BLDG NO T-82 AT URI LINE IN DAMANA UNDER GE JAMMU

Amount

B/R Portion: - Taking down chowkhats or frames with shutter without taking off shutter from the frame not exceeding 1.5 Sqm each including cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and as directed.

Taking down chowkhats or frames with shutter without taking off shutter from the frame exceeding 1.5 Sqm but not exceeding 4 Sqm each including cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and as directed.

Taking down shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) and removing unserviceable material exceeding 100 metres complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position complete all as specified and as directed by the Engineer-in-Charge.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including racking out joints, hacking for key, scrubbing with water etc complete all as specified and as directed.

Dismantling floors, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Dismantling of PVC, cast iron 100mm or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches if required complete all as specified and as directed.

Dismantling of PVC, cast iron 75 mm or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches if required complete all as specified and as directed.

Taking down GI tubing of 15 mm dia and connection and including cleaning for refixing or removal complete all as specified and as directed.

Taking down GI tubing of 20 mm dia and connection and including cleaning for refixing or removal complete all as specified and as directed.

Dismantling / disconnecting / demolition of water storage tank of any type or description PVC exceeding 250 and not exceeding 500 litres capacity and removing from site or refixing in position complete all as specified and as directed.

Taking out the roots of trees / shrubs of any girth from the surface of buildings and making good the damaged portion to match with the existing surface in cement mortar (1:3) or with PCC (1:2:4) or brick work in cement mortar (1:4) and finally finishing the surfaces to match with the existing surfaces complete all as specified and as directed.

Supply and fixing pressed steel frames for door (factory made) out of 1.25 mm thick black mild steel sheet with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc. complete size of frame 105x60mm including bottom of each chowkhat to be welded with 2 No's 25x25x3 mm thick flat iron projecting 10 cm on either side and back fill to chowkhats with PCC (1:3:6) type C-0 (using 12.5 mm graded crushed stone aggregate) including one shop coat of red oxide primer complete all as specified and as directed.

Supply and fixing pressed steel frames for door (factory made) out of 1.25 mm thick black mild steel sheet, with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc. complete size of frame 125x60mm including bottom of each chowkhat to be welded with 2 No's 25x25x3 mm thick flat iron projecting 10 cm on either side and back fill to chowkats with PCC (1:3:6) type C-0 (using 12.5 mm graded crushed stone aggregate) including one shop coat of red oxide primer complete all as specified and as directed. Note: - PCC (1:3:6) type C-O as in back fill will be paid separately.

Material and labour for cement concrete (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) as in backfill of pressed steel door frames complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet and edges will be painted to match with printed sheet, reinforced with mild steel square tube supplying and fixing in opening as per specification complete all as specified and as directed.

Supply and fixing solid PVC frame for cupboards of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet and edges will be painted to match with printed sheet, reinforced with mild steel square tube supplying and fixing in opening as per specification complete all as specified and as directed.

Supply and fixing 30 mm thick PVC wood grain printed factory made panel door shutter (style) consisting of frame made out of mild steel tubes for top and bottom rail, mild steel frame shall be covered with heat moulded wood grain printed PVC channel and 5 mm thick X 15 mm wide PVC sheet beading used inside style and rails and decorative PVC beading of 10x10 mm used instead of exposed portion of PVC sheet beading as in toilet/ Kitchen cabinet shutters complete all as specified and as directed.

Supply and fixing 30mm thick flush shutters, solid core construction, with particle board core and plywood face panels, both faces are covered with decorative face veener with lipping/ frame to match complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing for 35 mm thick Ist class hard wood factory made glazed and skelton shutters open rebated and prepared to receive glass/ wire gauge etc. without sash bar but with lock rail edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass/ wire mesh etc sizes of member as per clause 8.20 (a) of SSR Part -I for door shutter complete all as specified and as directed.

Material and labour for 18/19 mm thick prelaminated particle board interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work as in cupboard shutters/ pelmet box including teak wood beading all around complete all as specified and as directed.

Material and labour for 25 mm thick prelaminated particle board interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work as in cupboard shelves including teak wood beading all around complete all as specified and as directed.

Supply and fixing prepainted (factory painted) box type mild steel windows/ Ventilator (factory made) outer frame made out of ERW tube 'P' section 65X45X25 mm and shutter of ERW tube 'P' section 50mm X 35mm X 20mm openable (double shutter) with glazed shutter on external side and gauzed shutter fixed with galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm including necessary GI wire staples etc on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 no's on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler/ AC window complete all as specified and as directed and shown on drawings No CEPZTD-324/07 Sh 1/3 to 3/3. Notes: - The quoted rates shall also include: - (i) Two coats of synthetic enamel paint over one shop coat of zinc chromate primer on all exposed surface complete and one coat of tar on the ends of steel surface in contact with bricks/ concrete surface. Colour/ shade will be approved by Engineer-in-charge. (ii) 4 no's MS steel lugs made of 20X5 mm Iron flat 200 mm long. (iii) 10 mm Sq Bar grill/guard bar design as per drawing. (iv) PCC block for embedding lugs complete. (v) Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples complete.

Material and labour for PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed. Note: - Formwork required for these items included in the unit rate of this item.

Hacking out old broken glass of any thickness, size, quality or description from the wooden/ steel frames glazing with putty or fixed with wooden beads complete all as specified and as directed.

Supply and fixing 3.0 mm thick sheet glass ordinary quality glazing with steel pins, oil putty to steel windows and beads nails etc. to wooden surfaces as in square exceeding 0.50 Sqm in each pane complete all as specified and as directed.

Supply and fixing 3.0 mm thick figured glass, pin headed/ frosted head type and glazing with oil putty in square not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

Supply and fixing galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks or galvanized with staples including one coat of red oxide primer complete all as specified and as directed.

Supply and fixing mild steel butt hinges 100mm long medium weight cold rolled complete all as specified and as directed.

Supply and fixing 100 mm long hasp and staple, aluminium anodixed with bolt to hinge plate and fixed with screws complete all as specified and as directed.

Supply and fixing aluminium tower bolt of size 150 mm complete all as specified and as directed.

Supply and fixing aluminium handle of size 150 mm complete all as specified and as directed.

Supply and fixing in repair continuous piano hanges, mild steel, bright finish or electrogalvanised, width of flap 30mm (when open) fixed with welding complete all as specified and as directed.

Supply and fixing mild steel helical/ ordinary rat tail rod pattern door spring 300 mm including roller and roller plate complete fixed with welding complete all as specified and as directed. (ISI marked).

Supply and fixing small fittings Ist class hard wood such as brackets of any types latch and hinges blocks shaped door and window stops and the like, not exceeding 200 Cu cm each complete all as specified and as directed.

Supply and fixing aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and as directed.

Material and labour for glazed ceramic coloured tiles 300x450x7 to 8 mm thick on vertical surface as in skirting, dado set and jointed with neat cement slurry and pointed in white or coloured cement to match with the surface over and including taking down old plaster and 10 mm thick screed in cement mortar (1:4) complete all as specified and as directed.

Material and labour for non skid ceramic coloured tiles 7 to 8 mm thick (Square / rectangulament) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors over 15 mm thick screed in cement mortar (1:6) set and jointed in neat cement slurry and pointed in white/ coloured cement with pigment to match complete all as specified and as directed.

Material and labour for non skid ceramic coloured tiles 7 to 8 mm thick (Square/ rectangulament) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors over 15 mm thick screed in cement mortar (1:6) set and jointed in neat cement slurry and pointed in white/ coloured cement with pigment to match complete all as specified and as directed.

Material and labour for green marble work 18 to 20 mm thick (table rubbed and polished) in staples jambs, pillars, window cill, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Material and labour for machine cut kota stone slab flooring 20 mm thick laid over cement screed base 20mm thick in cement mortar (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting as required, rubbing and polishing to granite finish complete all as specified and as directed.

Material and labour for machine cut kota stone slab 18-20 mm thick as in riser of steps, skirting, dado and pillar laid over cement screed bed of 15mm thick in cement mortar (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting as required, rubbing and polishing to granite finish complete all as specified and as directed.

Material and labour for rendering 15 mm thick cement plaster, in the layer 10mm in (1:6) and 5mm in (1:4) on other than fair faces of brick work or concrete surfaces and to be finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 10 mm thick cement plaster (1:6) on fair faces of brick work or concrete surfaces and to be finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 5 mm thick cement plaster (1:3) on fair faces of concrete surfaces as in ceiling, chajja, shelves etc. finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 15 mm thick cement plaster (1:3) on other than fair faces of concrete surfaces as on fascia of roof slab, chajja, shelves etc. finished even and smooth without using extra cement (including all necessary scaffolding, lifting arrangement for three storey building on external surfaces) complete all as specified and as directed.

Supply and fixing PVC (SWR) 'P' trap 110/110 mm bore complete all as specified and as directed.

Supply and fixing PVC (SWR) pipes 110 mm bore single socketed in any length with rubber joint fixed to wall or laid in trenches or in floor with steel clamps complete all as specified and as directed.

Supply and fixing PVC (SWR) pipes 75 mm bore single socketed in any length with rubber joint fixed to wall or laid in trenches or in floor with steel clamps complete all as specified and as directed.

Supply and fixing PVC (SWR) bends of 110 mm bore complete all as specified and as directed.

Supply and fixing PVC (SWR) bends of 75 mm bore complete all as specified and as directed.

Supply and fixing PVC (SWR) junction double (double T) equal or unequal provided with access door of 110 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) junction single (single T) equal or unequal provided with access door of 75 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) reducer of 110 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) vent cowl 75 mm bore complete all as specified and as directed.

Supply and fixing PVC (SWR) water closet connector with lip ring 110 mm complete all as specified and as directed.

Supply and fixing in repair water closet Orissa pattern white with integral foot rest 580 x 440 mm including PCC bedding (1:2:4) and making good disturbed floor connecting to trap and flush pipe complete all as specified and as directed.

Supply and fixing in repair PVC low level flushing cistern 10 litre capacity white with inlet ball valve, float valve and handle including brackets, PVC flush pipe complete all as specified and as directed.

Supply and fixing in repair PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipes of 15 mm bore complete all as specified and as directed.

Supply and fixing in repair pillar taps 15 mm dia, cast copper alloy, with capstan heads, chromium plated fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and flynuts, screwed for iron pipe and fixed suitable for 15 mm bore complete all as specified and as directed.

Supply and fixing in repair vitreous china wash basin, white, flat back, size 580x450 mm including 32 mm dia PVC waste pipe, chromium plated brass waste coupling 32 mm dia, pair of mild steel brackets or mild steel fastener/ bolts for fixing arrangements and 450 mm long PVC connection with PVC nut and washer complete at site all as specified and as directed.

Supply and fixing in repair bib tap cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed for iron pipe, suitable for 15 mm bore complete all as specified and as directed.

Supply and fixing in repair stop valve/angle valve cast copper chromium plated screwed down high pressure with capstan head suitable for 15 mm bore, screwed both ends for iron pipe complete all as specified and as directed.

Supply and fixing in repair brass chromium plated shower rose 125 mm size swivel type with connecting rod 15 mm bore complete all as specified and as directed.

Supply and fixing in repair stop valve cast copper chromium plated concealed type screwed down high pressure with capstan head suitable for 15 mm bore complete all as specified and as directed.

Supply and fixing in repair stainless steel gratings of outer frame dia 150 mm openable type including all necessary fittings such as hinges including embedding in tiles with white cement complete all as specified and as directed.

Supply and fixing in repair curtain rod stainless steel with fixing brackets (wall or end), side ball stops, funnel, rollers, etc complete all as specified and as directed.

Supply and fixing 15 mm dia galvanised pipe medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply and fixing 20 mm dia galvanised pipe medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Fixing only 15 mm dia old galvanised pipes including new fittings where necessary fixed complete to wall and ceiling or laid in floor complete all as specified and as directed.

Fixing only 20 mm dia old galvanised pipes including new fittings where necessary fixed complete to wall and ceiling or laid in floor complete all as specified and as directed.

Cutting chases for concealed water tubing or concealed conduit and making good in cement mortar (1:3) of girth exceeding 10 cm and not exceeding 20 cm in brick wall complete all as specified and as directed.

Material and labour for 750 mm wide, 75 mm thick PCC (1:3:6) laid to an outward slope of not less than (1:12), cast in panels not exceeding 2.0 Sqm areas with 6 mm wide joints. The joint shall be filled with mastic filling and 10 mm wide joints between the walls and plinth protection shall be filled with mastic filling complete all as specified and as directed.

Supply and fixing rotational moulded polyethylene water storage tank with float valve, plastic lid cover, double layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 500 litre including making connections complete all as specified and as directed.

Supply and fixing in repair stop valve 20 mm dia cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe and fixed complete all as specified and as directed.

Material and labour for applying one coat of synthetic enamel paint tint over old painted steel surfaces over 10 cm in width or girth including preparation of old surfaces of steel complete all as specified and as directed.

Material and labour for preparation of new steel surface exceeding 10cm width or girth and applying two coats of synthetic enamel paint over priming with red oxide complete all as specified and as directed.

Material and labour for preparation of new wood or wood based surface and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Material and labour for applying two coats of oil bound distemper of wall to newly plastered surfaces including preparation of surfaces complete all as specified and as directed.

Material and labour for applying two coats of oil bound distemper of wall to old plastered surfaces including preparation of surfaces complete all as specified and as directed.

Material and labour for preparation of old plastered surfaces including filling of small holes etc and applying two coats of white wash over wall surface complete all as specified and as directed.

Material and labour for preparation of surfaces new plastered surfaces and applying three coats of white wash on ceiling complete all as specified and as directed.

Material and labour for applying two coats of cement based paint to newly plastered surfaces including preparation of surfaces complete all as specified and as directed.

Material and labour for applying two coats of cement based paint to old plastered surfaces including preparation of surfaces complete all as specified and as directed.

Supply and fixing in repair stainless steel kitchen sink with drainage board made of stainless steel of 1 mm thick sheet including plugs, washers and PVC waste pipe of 40 mm dia fixing with complete on appropriate size of cantilever brackets of mild steel angle or GI pipe 15 mm dia with proper arrangement to hold and fitting of sink complete all as specified and directed at site and connecting union to pipe. The overall size of sink 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

Supply and fixing in repairs stainless steel plate rack made out of 1mm thick sheet of size 750 x 600 x 250mm of size having partition and fixed with steel fasteners or steel screwed complete all as specified and as directed.

Material and labour for preparation of surface, the surface must be sound and free from dirt, dust and loose particles, thoroughly wire brush the surface and clean the dust, wash the surface with water. Any damage surface must be repaired by using polymer modified repair mortar with Dr. Fixit Pidicrete URP. Clean the surface, saturated with water and remove the excess water if any and bring to touch dry state. Applying the first coat of mixed (@ 75 Sqm/kg, 1mm thick for 2 coats) Dr Fixit Pidifin 2K on the prepared surface and allow to dry for 4 to 6 hours. Prepare another batch of Dr Fixit Pidifin 2K and apply 2nd coat in direction 90 degree to first coat. Overlay protected screed using cement sand (1:3) along with Dr Fixit LW+ complete all as specified and as directed.

Removing existing treatment from roof surfaces such as tiling, tarfelt, fungus, moss, dust etc., cleaning the surface of all foreign material by wire brushing and dusting and racking out RCC slab and removing the debris outside defence land complete all as specified and as directed.

Material and labour for rendering 20 mm thick in cement mortar (1:4) on fair faces of brick work surfaces finished even and smooth without using extra cement up including mixing liquid water proofing compound complete all as specified and as directed. Note: - Liquid water proofing compound shall be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and as directed.

Material and labour for roof treatment with the folowing specification: - (a) Applying evenly one coat of bituminous primer conforming to IS 3384-1986 @ 0.3 litres per Sqm over cleaned plastered surface. (b) Applying evenly one coat of blown Hot bitumen of grade 85/25 @ 1.2 Kg per Sqm on primed surfaces. (c) Applying a layer of APP based Polymeric Membrane 3mm thick (minimum) weighing 3.5 Kg per Sqm (reinforced) with polyster non woven fabric weighing not less than 160 gms per sqm by torch application. The overlap shall be minimum 100 mm on tranverse direction and 75 mm on longitudinal direction and sealing overlap by torch application. (d) Applying evenly one coat of aluminium paint @ 0.10 litre per Sqm over the APP based polymeric membrane.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing unserviceable material outside cantt area complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75mm thick cement concrete (1:3:6) type C-2 (using 40mm graded crushed stone aggrregate) as in plinth, path etc surface finished even and fair finish complete all as specified and as directed.

Material and labour for machine pressed precast concrete interlocking paver block with grey cement and pigment, any shape and size confirming to IS : 15658-2006 of 60 mm thickness, M-35 grade complete all as specified and as directed.

Material and labour for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

E/M Portion: - Taking down old unserviceable copper/ aluminium point wiring concealed / batten (light, fan, socket or power) complete including fixture and fittings such as switches, sockets, ceiling roses, bell push, bell electric, lamp holder, bulk head fitting, pendants, regulators, sockets, light fitting and any type of switch board wooden/ iron, round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

Taking down carefully unserviceable distribution boards of any type/ size with MCB's and disconnecting and making good disturbed surfaces complete all as specified and as directed.

Material and labour in replacement for sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 6 Sqmm for phase and neutral and one run of 6.0 Sqmm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/ neutral and one run of cable for earth will be measured and paid as one unit length including taking down old wiring complete all as specified and as directed. Note: - Wiring shall be done in proper colour coding.

Material and labour in replacement for complete point wiring with 1.5 Sqmm single core multistranded copper conductor FRLS insulated and unsheathed heavy duty cable in colour code including continuous earth wire with cable of size 1.5 Sqmm copper conductor flexible FRLS insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall, plastering after concealing conduit including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc and including making good the disturbed surface as per existing complete all as specified and as directed by Engineer-in-Charge for the following: -

Description all as per Ser item No 103.00 here-in-before but for multi 5 pin 5 amp socket outlet on same board ISI marked complete all as specified and as directed.

Description all as per Ser item No 103.00 here-in-before but for multi 5 pin socket outlet 5 amp socket on independent board ISI marked complete all as specified and as directed.

Description all as per Ser item No 103.00 here-in-before but for one bell/ buzzer point controlled by one push button on the same board with other switches or independent with cable 1.5 Sqmm size complete all as specified and as directed.

Description all as per Ser item No 103.00 here-in-before but for multi 6 pin 15 Amp socket outlet independent controlled by 15 Amp switch with 2.5 Sqmm copper conductor multistranded cable PVC insulated FRLS and unsheathed cable in and including PVC rigid concealed conduit 20/25 mm dia and unsheathed copper conductor multistranded cable 2.5 Sqmm as earth wire FRLS PVC insulated in green color complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement modular socket, 6A - 5 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in replacement modular switch 1 module 6A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in replacement modular bell push 6A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in replacement ceiling rose, 3 Pin/ PVC/ polycarbonate isolated body ISI marked complete all as specified and as directed.

Supply and fixing in replacement modular switch 1 way 16A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in replacement modular socket 6A/16A - 6 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in replacement calling bell Ding Dong/ buzzer AC 230 Volts, single pole ISI marked complete all as specified and as directed.

Material and labour in replacement for lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Material and labour in replacement self ballast LED retrofit lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and as directed.

Supply and fixing in replacement LED lights fitting 1 x 20 W, 220 V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.9, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing in replacement of Vertical distribution board (V.TP&N) 4 way double door suitable for TPN 4 pole 125 Amp 16 KA four pole as incomer, it should be IP-43 protected with copper bus bars, neutral links, earthing bar complete all as specified and as directed.

Material and labour for replacement distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and as directed by Engineer-in-Charge. Note:- Distribution board and MCB's should be of same make.

Supply and fixing in replacement SPN 40 to 63 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing in replacement 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole and current carrying capacity 6 to 32 Amp complete with connection, testing and commissioning complete all as specified and as directed.

Material and labour in replacement for earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 metre deep below normal ground level with top edge of the earth plate not less than 1.5 metre below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC (1:2:4) type B-1 precast RCC cover slab using reinforcement with suitable handle made of round bar including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and as directed.

Supply and fixing in replacement LED light fitting 10 W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal managment in multiple optics complete with IP-65/66 protection all as specified and as directed.

Supply and fixing in replacement 415V 10KA 'B' curve miniature circuit breaker (MCB) TPN 4 pole, upto 125 Amps of foloowing poles and current carrying capacity in the distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing in replacement fan step regulator, 100W - 1 module 240 volts ISI marked complete all as specified and as directed.

Disconnecting and taking out defective service cable in any size and any type from roof, pole, pipe, floor, wall etc complete all as specified and as directed.

Supply and laying, connecting and testing XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 volts grade 16 Sqmm 4.0 core laid in trenches/ on poles/ road crossing or passing through existing/ new pipe under road crossing, clamping on wall etc. complete all as specified and as directed. Notes: - (i) Earth work, sand, bricks, removing, returning filling aluminium thimbles/lugs will be paid separately. (ii) Cost of laying electrical cable through new/existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new/existing pipes are to be provided by the contractor without any extra cost.

M/S VERMA ENTERPRISES (BID ID -3225662)

Malik Construction (BID ID -3225698)

Hare krishna engineering const. (BID ID -3224398)

AJAY KUMAR (BID ID -3224071)

Kanwal Nain Behl (BID ID -3225437)

STAR CONSTRUCTIONS (BID ID -3226003)