Construction of Remaining work of Non-Residential Building at Sub-Jail,Chakradharpur in the District of West Singhbhum,Chaibasa

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Extra for E/W in hard soil as per specification and direction of E/I (Vide classification of soil item- B)

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75 B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75 B brick work in C.M.(1 :6) in superstructure with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scafolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 125 mm thick reinforced designation 75 A brick work in C.M (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials , scafolding, raking out joints to 15 mm depth, curing, taxes and royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/l.

1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Columns, Pillars, Piers, Abutments, Posts and Struts

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Suspended floors, roofs, landings, balconies and access platform

Stairs, (excluding landings) except spiral-staircases

Providing G.I pipe hand rails with 40 mm dia G.I. pipe of I.T.C. or equivalent make properly fitted and fixed in position to rail posts with all necessary accessories and taxes all complete as per building specification and direction of E/l.

Suppling, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows, skylight, fanlights and C/W celetial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush shutters in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Supplying fitting and fixing 38 mm thick good quality well dressed and well seasoned Sal wood battened shutters, ledged and braced in doors and windows with oxidised iron fittings such as hinges, sliding door, bolts, tower bolts, handles or rings, hooks and eyes, cleats, sand blocks as per schedule taxes and royalty all complete as per building specification and direction of E/l.

Supplying , fitting and fixing 38 mm thick good quality well dressed and well seasoned Sal wood fully paneled shutters in doors and windows with 25 mm thick panels with one side plain and other side chamfered with oxidised iron fittings such as hinges, sliding door, bolts, tower bolts, handles or rings, hooks and eyes, cleats, sand blocks as per schedule taxes and royalty all complete as per building specification and direction of E/l.

Providing Tor steel reinforcement 8mm dia rods as per approved design and drawing excluding carriage of M.S. bars to work site cutting, bending, and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (Only Valid for SAIL & TATA Steel, JSPL ,Electro Steel Ltd. and Vizal Steel)

Providing Tor steel reinforcement rods as per approved design and drawing excluding carriage of M.S. bars to work site cutting, bending, and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.

(a) 10mm (TMT,Coil Fe 500) (Only Valid for SAIL & TATA Steel, JSPL ,Electro Steel Ltd. and Vizal Steel)

(b) 12mm (TMT,Coil Fe 500) (Only Valid for SAIL & TATA Steel, JSPL ,Electro Steel Ltd. and Vizal Steel)

(c) 16mm (TMT Coil Fe 500) (Only Valid for SAIL & TATA Steel, JSPL ,Electro Steel Ltd. and Vizal Steel)

Providing Tor steel reinforcement rods as per approved design and drawing excluding carriage of M.S. bars to work site cutting, bending, and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.

(a) 20 mm dia TMT bar Fe 500 (Only Valid for SAIL & TATA Steel, JSPL ,Electro Steel Ltd. and Vizal Steel)

(b) 25 mm dia TMT bar Fe 500 (Only Valid for SAIL & TATA Steel, JSPL ,Electro Steel Ltd. and Vizal Steel)

Supplying, fitting and fixing 250x20x6mm L-type M.S. Clamp properly fishtailed, including making holes and setting the same in 375x125x75mm. cement concrete block (1:2:4 )with cost of all labour and materials and taxes as per building specification and direction of E/l.

Providing and fixing fan hook of 16mm dia M.S. bar 1 metre long bent to required size and shape, placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/l. (where material is not supplied by deptt.)

Supplying, fitting and fixing callapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2 mm at 100mm. centres and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40x40x6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, carriage , hoisting and taxes all complete as per building specification and direction of E/l.

Supplying, fitting and fixing fully glazed steel door, windows or ventilations of standard rolled 'Z' and mullion steel sections and size as per IS-1038 joints met and welded with 100x16x3mm M.S. lugs fixed in cement concrete (1:2:4) blocks 15x10x10 cm size including cost of oxidised iron fittings, with hinges, handle per steps, catch springs, 3mm thick plain glass panes with Aluminimum beads and inner frame fixed with lugs with 20mm long 6.3mm G.I. counter sunk machine screw and nuts and applying a coat of red lead paint carriage to work site hoisting and placing in position in all storys and taxes all complete as per building specification and direction of E/l.

Supplying, fitting and fixing 40mm dia G.I. pipe fitted and fixed in floor outlet to drain out water, in cement concrete including cutting hole, making good the wall and finishing, all complete as per building specification and direction of E/l.

Labour for fabricating, erecting, hoisting and fixing in position structural steel work in R.S. joist, channel, Angle, Tee, flat, plate, latice member, built up compound section in column, girder, staircase or truss including cost of gusset plates, holding down bolts, anchor plates at all heights and depths, bolting, welding (machining wherever necessary) with applying a priming coat of red lead paint all complete as per approved drawing, building specification and direction of E/l.

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing designation 75 B one brick on edge soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing 25 mm thick first class patent stone flooring (1:2:4) with stone chips in two layers, bottom layer 19 mm thick (1:2:4) with 12 mm to 6mm size graded stone chips and top layer 6 mm thick (1:2) with 6mm down stone chips, in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royalty with all complete as per building specification and direction of E/l

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing, taxes and royalty all complete as per building specification and direciton of E/l.

With "A" grade white 15 x 15 cm tiles.

Providing 50 mm thick cement concrete flooring (1:2:4) with 20 mm to 6mm size graded stone chips finished with floating coat of neat cement in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royalty with all complete as per building specification and direction of E/l

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M 1.5 including screening curing with all leads and lifts of water scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:4) with clean coarse sand of F.M 1.5 including screening curing with all leads and lifts of water scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 1.5 mm cement punning including curing carriage of water with all leads and lifts as per building specification and direction of E/I.

White washing three coats over new surface with approved quality of lime including cost of cleaning surface thoroughly and removing the scales of smoke and mosh marks with jhama rubbing, scaffolding, washing, of floors and taxes all complete as per building specification and direction of E/l.

Colour washing two coat over a coat of white wash over old surface with approved quality of lime in approved shade including cost of cleaning surface thoroughly and removing the scales of smoke and mosh marks with jhama rubbing, scaffolding, washing, of floors and taxes all complete as per building specification and direction of E/l.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l.

Providing two coats of snowcem of approved shade and make over old surface including washing cleaning, and preparing the walls, scaffolding, curing and taxes all complete as per building specification and direction of E/l.

Providing two coats of synthetic enamel paint over a coat of primer of approved shade and make over new wooden surface after cleaning, removing dirt, scales, smokes, grease and sand papering, including cost of scaffolding and taxes all complete as per building specfication and direction of E/l.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing rust , dirt, , scales , smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/l. ( Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification)

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Labour for fitting and fixing G.C.I, or C.A. sheet roofing in proper slope including the cost of "J" or "L" hooks, limpet and bitumen washers, carriage of sheets to work site, and taxes all complete as per building specification and direction of E/l.

Labour for fitting and fixing G.C.I: or C.I. sheet ridge including the cost of "J" or "L" hooks, limpet and bitumen washers, carriage of sheets to work site, and taxes all complete as per building specification and direction of E/l.

Providing 250mm. wide brick drain in cement mortar (1:6) with av. 250mm. clear depth and 250mm. apron including cost of earthwork involved with 75 mm. ~ cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M.(1:3) with punning over exposed surface all complete as per building specification and direction of E/l.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and rrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Supplying G.I sheet thickness 0.80 mm as per IS 22.7 at site rate exclusive of GST

Supplying iron and steel materials at site rate exclusive of GST as per I.S. 226 RS Joist in size-300x140 (Gr.A)

Supplying iron and steel materials at site rate exclusive of GST (a) Plate size in mm as per IS-226 (over 12 upto 20mm) Plate)

Supplying iron and steel materials at site rate exclusive of GST (b) Angle size in mm as per I.S. 226

130x130x12mm Gr-A

100x110x12mm Gr-A

80x80x10mm Gr-A

Carriage of Material incluiding loading & unloading and stacking

(i) Sand

(ii) Bricks

(iii) Stone chips

(iv) Stone metal

(v)Stone Boulder

(vi) Earth

Providing rough dressed course stone masonry in C.M. (1:6) in foundation and plinth with hammer dressed stone of less than 0.03 M3 in volume and clean coarse sand of F.M. 2 to 2.5 including cost of screening, raking out joints to 20mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation stone boulder soling joints with local sand including cost of watering taxes and royalty all complete as per building specification and direection of E/I

Providing 12mm C.P (1:3) with clean coarse sand of F.M 1.5 with floating coat of neat cement in skirting including foundation of junctions with floor, curing taxes and royalty all complete as per building specification and direction of E/I.

Supplying, fitting and fixing M.S. grill gate with M.S. grills made of 20x6mm M.S. flats or 16mm square bars fitted on 25x25x6mm M.S Angle frame including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l. (where steel is not supplied by the deptt.)

Supplying labour and tools for fixing G.I. pipes with Red lead and yarn of following nominal bore with screwed and socketted joints on wall, ceiling and floor including supplying and fitting of wall hooks or pipe clamps, wooden plugs, cutting pipes to size and threading ends if required etc. all complete as per specification and direction of E/l. (Pipe with socket to be supplied deparmentally free of cost ).

(a) 15 mm dia Normal bore G.I. Pipe

(b) 20 mm dia Normal bor G.I. Pipe

(c) 25 mm dia Normal bor G.I Pipe

(d) 50 mm dia Normal bor G.I. Pipe

Supplying G.I. pipe (Tata mark) or Equivalent as per IS. 1239 (part-I)/2004 ISI marked /medium Quality

(i) 15 mm dia

(ii) 20 mm dia

(iii) 25 mm dia

(vi) 50 mm dia

Providing and placing on terrace (at all floor levels) polythylene water storage tank ISI 12701 marketed with cover and suitable locking arrengment and making necessary holes for inlet outlet and overflow propose but without filings and the base supported for tank.

Laying of G.I pipes of approved make in trenches with red lead and yarn with socket and screw joints, and cutting pipes to size and threading ends where necessary etc. all complete as per specification and direction of E/l

(a) 25 mm dia G.I. Pipe

(b) 50 mm dia G.I. Pipe

Providing and fixing brass / C.I. Stop cock of approved quality all complete as per specification and direction of E/l .

Brass Stop Cock

(a) 15 mm dia

(b) 20 mm dia

C) 25 mm dia

(d) 50 mm dia

Supplying and fixing G.I fittings of approved make all complete as per specification and direction of E/l

(A) Elbow

(a) 15 mm dia

(b) 20 mm dia

(c) 25 mm dia

(d) 50 mm dia

(Bl TEE (PLAIN)

(a) 15 mm dia

(b) 20 mm dia

(c) 25 mm dia

(d) 50 mm dia

(C) REDUCING SOCKET

(a) 20 mm dia

(b) 25 mm dia

(c) 50 mm dia

(D) Nipple

(a) 15 mm dia

(b) 20 mm dia

(c) 25 mm dia

(d) 50 mm dia

(E) PLUG

(a) 15 mm dia

(b) 20 mm dia

[c) 25 mm dia

(d) 50 mm dia

(F) Reducing Tee Plain (Taking larger dimension)

(b) 20 mm dia

(c) 25 mm dia

(d) 50 mm dia

(G) UNION SOCKET

(a) 15 mm dia

(b) 20 mm dia

c) 25 mm dia

(d) 50 mm dia

(H ) SOCKET PLAIN

(a) 15 mm dia

(b) 20 mm dia

(c) 25 mm dia

(d) 50 mm dia

(J) Jam Nuts

(a) 15 mm dia

(b) 20 mm dia

(c) 25 mm dia

(d) 50 mm dia

Earth work in excavation ( as per I.S. 3114/1965 for laying of different types and sizes of pipes so as to give 1 m av. cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of E/l.

a) For classification of soil item- A

Earth work in back filling the trenches after laying different types and size of pipes with earth removed dufing excavation within initial lead and lift as per specification and direction of E/l. ( For classification of Soil item - A & B)

Providing and fixing male ended 15 mm dia brass bib cock of approved quality ( wt not less than 350 gms ) with extra socket all complete as per specification and direction of E/l .

Cutting floor for laying G.I pipes and restoring the same as per specification and direction of E/I

Providing and fixing 15mm size C.P brass pillar cock (Weight not less than 350 gms) C.I body brass spindle pillar cock of approved quality as per spcification and direction of E/l.

(b) C.I. body brass spindle

Supplying and fixing G.M. ferrule of approved make in existing C.I main including drilling and taping C.I main all complete as per specification and direction of E/l.

(c) 22 mm and 25 mm dia ferrule weight not less than 900 gms.

Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l

(f) 50 mm dia wt not less than 1.5 kg

Making long screw in G.I. pipe including supplying and fitting jam nuts and extra socket etc. all complete as per specification and direction of E/I.

(a) 15 mm dia

(b) 20 mm dia

(c) 25 mm dia

(d) 50 mm dia

Cutting chajja or cornice for laying G.I pipe and restoring the same with R.C.C (1:2:4) brick work in cement mortar (1:4) and cement plaster (1:4) as per specification and direction of E/l.

Making holes in walls for laying G.I pipes and restoring the same after pipe laying as per specification and direction of E/l

(a) 125 mm thick wall.

(b) 250 mm thick wall.

(c) 375 mm thick wall.

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/l.

1) 600 x 125 mm glass shelf

(b) Mirrors of 4 mm thick plate glass bevelled edge mirror including C.P brass revolving fittings, 3 mm plywood board and C P hinges to fix with mirror

( c) C.P brass towel rail 20 mm x 600 mm with bracket container

(v) C.P. brass soap dish container medium quality with acrew and hinges etc.

Providing and fixing N.P/C.P brass/P.V.C porcelain shower rose of 15mm inlet etc. all complete as per specification and direction of E/l (A) C.P. SHOWER

(b) 125 mm dia. C.P shower

Providing and fixing G.M. non return valve Horizontal / vertical type of approved quality as per specification and direction of E/l.

(A) Horizontal non return valve 25 mm

(B) Vertical non return valve 25 mm

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. (A) 580 mm long

(c) with 12.5 lit. low level P.V.C. cistern

Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. (A) With "P" trap

(b)12.5 lit. low level P.V.C. cistern

Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthenware urinal of "Hindustan" " Parry" or any other approved I.S.S. make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15 mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grms. , 15 mm P.V.C. alkathene pipe 450 mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l.

(A) Flat back or standing corner ( 450 mm x 350 mm )

Supplying, fitting and fixing viterous white glazed earthen ware indian squating type 600 x 350 mm urinal plate of Parry Hindustan or any other I.S.S. approved make with internal flushing rim 100 mm white glazed earthen ware channel about 1m long 5litre capacity C.I. automatic flushing cistern of reliance or any other approved make with fittings C.I. or R.S. brackets 15 mm & 45 cm long P.V.C. alkathene pipe standard G.I. flush pipe for back and front with spreader fitting and brass coupling etc. 15mm C.I. body brass spindle stop cock weight not less than 450 grms. all complete including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l.

(A) 600 mm x 350 mm size ( large )

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l.

Supplying fitting and fixing H.C.I, pipes with ear of approved make confirming to I.S.I. 1729 including supplying nails and bobins short pieces, cutting loose collars, lead and yarn for making lead chaulked joints, cutting pipes to size including earth work or scaffolding where neccessary etc. all complete as per specification and direction of E/l.

(a) 100 mm dia

(b) 75 mm dia

© 50 mm dia

Supplying materials and labours for painting the exposed H.C.I, pipes and fittings with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.

(a) 100 mm dia

(b) 75 mm dia

© 50 mm dia

Supplying, fitting and fixing white glazed fires clay sink of approved make with overflow arrangements supported on C.l. or R.S. painted brackets 40 mm dia C.P. brass waste with C.P. brass chain and rubber plug, 40 mm dia P.V.C. waste pipe about 750mm long with brass coupling at one end and 15 mm C.I. body brass spindle bib cock of approved quality of weight not less than 450 grms. including cutting wall and making good the same etc. all complete as per specification and direction of E/l.

(a) Kitchen sink of size 600 mm x 450 mm x 250 mm

Supplying and fixing H.C.I, fittings of approved make confirming to I.S.S. 1729 including supplying nails and bobins lead and yarn for making lead chaulked joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/l. (A) H.C.I, single junction with door but without ear except socket

(i) 100mmdia(Wt. 10.5 Kg. app.)

(ii) 80 mm dia (Wt. 7 Kg. )

(B) H.C.I. Heal Rest Bend

(i) 100 mm dia (Wt. 5.5 Kg. app.)

(ii) 80 mm dia (Wt. 4 Kg. app.)

( C) 100mm dia H.C.I."P" TRAP with Anti syphonage Horn (Wt. 8.5 Kg. app.)

(D) H.C.I, double junction with door and ear

(i) 100 mm dia (Wt. 15.5 Kg. app.)

(ii) 80 mm dia (Wt. 15.5 Kg. app.)

(G) H.C.I, bend with door and ear

(i) 100 mm dia (Wt. 6.5 Kg. app.)

(ii) 80 mm dia (Wt. 4.5 Kg. app.)

(H) H.C.I plain bend with ear

(i) 100mm dia (Wt. 5.5 Kg. app.)

(ii) 80 mm dia (Wt. 3.75 Kg. app.)

(K) Norton patent H.C.I, cowel

(i) 100 mm dia (Wt. 3.25 Kg. app.)

(ii) 80 mm dia (Wt. 2.25 Kg. app.)

(J) Floor trap with gratinqs

(i) 100mmdia

Supplying all tools and labours and cutting chajja, cornice, for laying H.C.I, pipes and making good the same as per specification and direction of E/l.

Making holes in wall for laying H.C.I, pipe and restoring the same after pipe laying as per specification and direction of E/l.

(i) 375 mm dia

(ii) 250 mm dia

(iii) 125 mm dia

Supplying NP2 250mm dia RCC Hume pipe with coller as per ISS 458 -1971 including all taxes and royalty etc. as per building specification and direction of E/I

Labour for laying, fitting and fixing NP2 R.C.C. spun pipe with collars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak proof including providing sight rails, bonning rod, night guard, red light and barrier etc. all complete as per specification and direction of E/l.

250 mm dia R.C.C. spun pipe Upto 3.0 meter depth of invert below G.L.

Earth work in excavation for laying of different types and sizes of R.C.C. spun pipes with disposal of excavated earth within initial lead and lift as per specification and direction of E/l.

(a) For classification of soil item- A

Earth work in back filling the trench after laying different types and sizes of R.C.C. spun pipes with removed during excavation within initial lead and lift as per specification and direction of E/l.

Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750 mm deep, 600 x 450 internal dimension having 250 mm wall thickness in cement mortar ( 1:6 ) including 3 mm cement plaster ( 1:4 ) with punning on inside and cement plaster (1:6 ) with 600 x 475 mm G.I. cover with frame (Weight not less than 36 Kg.) in foundation and refilling all complete as per specification and direction of E/l.

Supplying NP2 150mm dia RCC Hume pipe with coller as per ISS 458 -1971 including all taxes and royalty etc. as per building specification and direction of E/I

Labour for laying, fitting and fixing NP2 R.C.C. spun pipe with collars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak proof including providing sight rails, bonning rod, night guard, red light and barrier etc. all complete as per specification and direction of E/l.

150 mm dia R.C.C. spun pipe Upto 3.0 meter depth of invert below G.L.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with piano type switch phenolic laminated sheet, suitable size PVC / GI box etc. as required.

(i) Group (B)

(i) Group (C)

Supplying and fixing folloing Piano type switch / Socket on the existing switch box/cover including connection etc. as reqd.

15/16 amps, one way switch

Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

2 X 10 sq. mm + 1 X 10 sq. mm earth wire

2 X 16 sq. mm + 1 X 16 sq. mm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection,painting etc. as required.

Supplying and fixing suitable size GI/PVC box on surface or in recess,with phenolic laminated sheet cover in front including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps piano type switch, connection,painting etc. as required.

Supplying and fixing batten/ angle holder including connection etc. as required.

Supplying and fixing 2 pin 5 amp Ceiling rose on the existing junction box/ wooden block including connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for D.C/A.C single phase, 230 volts, complete as required.

Supplying and fixing following way, single pole and neutral, sheet , MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

2 +4 way, Single door

4 +8 way, Single door

Supplying and fixing 6 amps to 32 amps rating 240 volts 'B' Series miniature circuit breaker suitable for lighting and other loads of following pole in the existing MCB DB complete with connection testing and commissioning etc. as reqd.

6/32 amps, single pole of "B" Series

Supplying and fixing following rating, four pole,, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Providing and fixing following capacity double pole / TP & N sheet metal switch disconnector fuse unit in exising metal board with rewireable type fuses, including drilling holes in metal board, making connections, etc. as required.

100 Amp TP&N switch

63 Amp TP&N Switch

32 Amp TP&N

Supplying and fixing following rating double pole (Single phase and neutral) 240 volts, residual current circuit breaker (RCCB) having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

63 Amp SP&N Switch

Providing and fixing following capacity busbar chamber with 4 strips of suitable size made of copper heavy duty, complete with all accessories including connections, earthing the body, etc. as required.

Providing and fixing following capacity 2 pole / 4 Pole on/off load change over switch with side handle opening in sheet enclosure exiting metal board including drilling holes in metal board, making connection, earthing the bordy etc. as required.

100 amps 4 pole

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required.

Extra for using salt and coke for G.I or Copper plate earth electrode as required for two set lighting conductor .

Supplying and laying 8 SWG Copper. wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required.

I.T.C of ceiling fan including wireing the down rods of standard length (Up to 30 cm) with 1.5 sq.m FRPVC wigh 1.5 sq.mm FRPVC insulated copper conductor single core cable etc. as required.

Installation of exhaust fan upto 450mm/sweep in the existing opening, including making the hole to suit the size of the above fan making good the damage, connection, testing, commissioning etc. as required.

(ii) Supply 3.5 coare 95 sq.mm Armoured cable

(iii) Supply 3.5 coare 50 sq.mm Armoured cable

(iv) Supply 3.5 coare 25 sq.mm Armoured cable

(v) Supply 2x10 coare 25 sq.mm Armoured cable

Laying of cable in cable trench including excavation sand filling and brick work all complete (Large size)

Laying of cable in cable trench including excavation sand filling and brick work all complete (Average size)

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP, MCCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and drawing following pair 0.5 sq mm FR PVC insulated copper conductor, unarmored telephone cable in the existing surface/ recessed PVC conduit as required.

Supplying and fixing Telephone socket/ out let as reqd. on the existing switch box(caller) including connections etc. as required.

S/F metal box of following size with suitable size phenolic laminated sheet cover 75x75x60 mm deep etc. as reqd in front including pointing etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, copper tube, having single prong at top, with 85 mm dia 3 mm thick copper base plate including holes etc. complete as required.

Fixing of lightning conductor finial made of 25 mm dia 300 mm long, copper tube/G.I tube, having single prong at top, with 85 mm dia 3 mm thick copper base plate including holes etc. complete as required.

Revetting sweating and soldering of copper /G.i tape (with another copper /G.I tape , base of the final or any other metallic object) as required

Providing and fixing copper tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing copper tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick copper strip, 125 mm long, with 4 nos. of tinned brass bolts, nuts, chuck nuts and spring washers etc. complete as required.

Laying copper/ G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

P/F 25mm x5mm copper strip in 40 mm dia G.I pipe from earth electrode etc. as required.

Supplying and fixing suitable size GI/PVC box on surface or in recess,with phenolic laminated sheet cover in front including providing and fixing 5 pin 5/6 amps socket outlet and 5/6 amps piano type switch, connection,painting etc. as required.

Supplying and fixing following rating, double pole, , 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Earthing with copper. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required.

Providing and fixing following capacity double pole / TP & N sheet metal switch disconnector fuse unit in exising metal board with rewireable type fuses, including drilling holes in metal board, making connections, etc. as required.

200 amps TP & N

Supplying and fixing following way, single pole and neutral, sheet , MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 way, Double door

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)Single socketed pipes. 75 mm diameter

75 mm diameter

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick

Providing and laying Rectified glazed Ceramic floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours White, Ivory, Grey, Fume Red Brown laid on 20mm thick bed of Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

Providing and applying plaster of paris (POP) putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

P/F pressed steel door frames of 1.25mm thick commercial mild steel sheet -do-do- with steel butt hinges and a coat of steel primer all complete job. Profile B

Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing on wall face unplasticised-PVC moulded fitting/accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion.

75 mm bend

Coupler

Shoe(Plain)

75 mm shoe

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Making soakpit 2.5 m m dia meter deep with 45x45 cm dry brick comb shaft with brick of class designation 75 and S.W. Drain pipe 100mm diameter , 1.8 long complete as per standard design (with F.P.S. brick)

Providing and fixing PTMT grating of approved quality and colour. Circular type

100 mm nominal dia

Non-Schedule Items

Providing 25mm dia M.S. grating in 50x10mm flat as per design drawing all complete as per building specification and direction of E/I

Supply & Fitting Special type Bulk Head fittings with 100 W Bulb etc. as reqd. all complete as per building specification and direction of E/I

Supply & Fitting 100 W Bulb etc. as reqd. of ISI mark all complete as per building specification and direction of E/I

Supply , Fitting & Fixing 4'x40 wattl single box type tube light fittings with all accessories viz chock starter with duly wire up ready for use on 220V /SP/ all electrict of philips/ Bajaj/ Cramption. all complete as per building specification and direction of E/I

Supply & Fitting 4'x40 watt double box type tube light fittings with all accessories (Bajaj/Philips/cremption all complete as per building specification and direction of E/I

Supply & Fitting 4'X40 watt tube light all complete as per building specification and direction of E/I

Supply of 48" (1200 mm) ceiling Fan of I.S.I mark all complete as per building specification and direction of E/I

Supply of 12" dia khaitan india Exhaust Fan of I.S.I mark all complete as per building specification and direction of E/I

Supply , Fitting & Fixing 250 wat HPSV fitting complete set with chak ignitar, lamp etc. as required all complete as per building specification and direction of E/I

Supply & Fitting 2 Amp . D.P. Switch all complete as per building specification and direction of E/I

Supply & Fitting 20 watt CFL as reqd. of I.S.I mark (Tomado Philips make)all complete as per building specification and direction of E/I

Supply & Fitting integral flood light luminarie compute with all accessories (without lamp) etc. as required. all complete as per building specification and direction of E/I

Supply & Fitting metal Lamp 400 watt etc. as required. all complete as per building specification and direction of E/I

End Termination of cable (25mm x 4 core) all complete as per building specification and direction of E/I

Supply of 56" (1400 mm) ceiling Fan of I.S.I mark all complete as per building specification and direction of E/I

Add 12% GST

Add 1% Labour Cess

M/s Raj Construction