Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹1.5 CrAccepted-AOC OFFICE NO 2 GROUND FLOOR CO OP HSG SOCIETY SBS ROAD COLABA MARKET MUMBAI 400 005 | MUMBAI | MAHARASHTRA | 400005 | ₹1.5 Cr | L1 | Accepted-AOC Beingh lowest |
| 2 | L2₹1.7 Cr+₹21.0 L (14.1%)Rejected-Finance 15 281 CHHILI INT ROAD GHATIYA AZAM KHAN AGRA UTTAR PRADESH 282003 | AGRA | UTTAR PRADESH | 282003 | ₹1.7 Cr+₹21.0 L (14.1%) | L2 | Rejected-Finance Being other than lowest |
| 3 | L3₹1.8 Cr+₹32.1 L (21.6%)Rejected-Finance NOT AVAILABLE | FARIDABAD | HARYANA | 121004 | ₹1.8 Cr+₹32.1 L (21.6%) | L3 | Rejected-Finance Being other than lowest |
| 4 | L4₹1.9 Cr+₹42.5 L (28.6%)Rejected-Finance GARDEN AVENUE PLOT NO 242 243 244 RH 4 SECTOR 21 NERUL NAVI MUMBAI 400 706 | THANE | MAHARASHTRA | 400706 | ₹1.9 Cr+₹42.5 L (28.6%) | L4 | Rejected-Finance Being other than lowest |
| 5 | L5₹1.9 Cr+₹45.7 L (30.7%)Rejected-Finance BLOCK C 14 GROUND FLOOR PLOT 618 624 BHIVANDIWALA TERRACE JAGANNATH SHANKARSHETH MARG DHOBI TALAO NEAR KALBADEVI POST OFFICE MUMBAI 400002 | MUMBAI | MAHARASHTRA | 400002 | ₹1.9 Cr+₹45.7 L (30.7%) | L5 | Rejected-Finance Being other than lowest |
Tender Value
Refer Docs
EMD Value
₹3.0 L
Closing Date
12 Jun 2021, 6:00 pmClosed
CWE NW MUMBAI
Commander Works Engineer NW Dr Homi Bhabha Road Navy Nagar Colaba Mumbai 05
ADDITION/ALTERATION AND SPECIAL REPAIRS TO BUILDING P 13A DSC LINE SHIKRA NAVAL DOCKYARD MUMBAI UNDER GE (NW) NOFRA COLABA MUMBAI
2021_MES_439390_1
8676/CWE(NW)/MUMBAI
Open Tender
Civil Works
Item Rate
270 days
GE (NW) NOFRA
Class B and above
7 documents required · 7 mandatory
₹2,000
Yes
GE (NW) NOFRA
₹3.0 L
Yes
20 Jul 2021
29 Apr 2021
14 Jun 2021
29 Apr 2021
12 Jun 2021
29 May 2021
29 Apr 2021 - 19 May 2021
Amount
Taking down cement or cement lime plaster of any description on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for chipping , removing carefullly concrete work by low impact hammer, breakar without damaging the structure & cleaning and disposal of debris out side the premises etc. complete all as specified as directed by Engineer-in-charge. Hard concrete should not be removed by force.
Height upto and including 4th floor
Height from 5th floor and above
Demolition of reinforced cement concrete of any description and in any position ( reinforcement cut as required to facilitate demolition whenever required), complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Demolition of brick work or stone masonary built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material & labour for cleaning existing reinforcement with wire/ rotary wire brush, making the surfaces free from loose material dirt etc. complete and applying two coats of alkaline rust converting primer FEOVERT of Krishna Conchem or Roff rust cleaner of Piddilite or Dr. Fixit Rust removal or ShaliRust of STP Ltd. on the rebars, including cleaning the reinforcement, wirebrushing to remove loose rust spalls, wash the rebars with clean water within 3 min and wipe it dry all as per manufacturer's instructions and complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for replacement of steel reinforcement with TMT bars of appropriate size where 30% of cross section is reduced including dismantling of rusted steel complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material & labour for carry out application of Bi-polar migratory corrosion inhibitor EPCO-KP-100/ Protectsil CIT/Ferogard 903 on concrete surface (this inhibitor shall have migratory kind of property which permits the material to migrate to a virtual extent of 100 mm, through pores of concrete, inhibitor the corrosion and de-passivating the Electro-chemical reaction. It should have properly to attack as well as cathode, which is purely alkaline in nature (pH-9.5), So it has no carcinogen activity with concrete all as per manufacturer's instructions complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material & labour for Drilling and fixing Rohibb Teflon nozzles in RCC members, including drilling holes of 12mm dia, 50 to 100mm deep holes. Works shall be carried out as under :- (i) Cleaning of holes. Clean the holes by air blower prior to fixing nozzles. (ii) Fixing of nozzles. Insert 12mm dia. Rohibb Teflon nozzles in cleaned holes. External end of nozzles to be machine to receive outlet of grouting gun.Fix it inside the holes by applying thixotropic epoxy putty to ensure complete sealing. Cure the system for minimum 12 hrs. (iii) Cutting of nozzles. Cut the nozzles by chisel after completion of grouting without damaging structural elements. (iv) In case crack upto 2mm wide, fix the injection nozzels directly over the cracks, at intervals of 6 to 9 inches, using a drilling machine. Fix PVC/MS nozzels in these holes with fast-setting epoxy putty & let it dry for 2 to 3 days. Also, seal the crack between the ports with epoxy putty. (v) In case where the crack is wider than 2mm upto 4 to 5mm, drill holes at the sides of the crack in a staggered fashion, at intervals of 6 inches and affix them with epoxy putty as mentioned above. (vi) Also, seal the face of the crack with a liberal application of the epoxy putty. Make Dr Fixit, STP, Choksy Chemical as approved
Height upto and including 4th floor
Height from 5th floor and above
Material & labour for Injecting of site cement slurry grout, in the ratio 1:2 (1-cement 2-water) including super plasticizer (supercom-100) 250 ml/50 Kgs. Mixing shall be done by mechanical mixer continuously stirring mechanically to keep cement particles in suspension. Injection of approved/specified grout by means of pump at a pressure of 0.5 Kg/cm2 till the grout mix flow out from the nozzle indicating complete filling of grout in the holes drilled complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material & labour for Injecting low viscosity MONOPOL (3-5 cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories till nozzles refuses to accept the grout, including, mixing of material mixing of material components(part a & b) in the required quantities as per manufacture`s instruction by weigh batching, Grouting maintain the pressure at exit(0.5 to 1.0 kg/cm2) by monitoring pressure gauge at exit grout the material through prefixed nozzles in the structural elements@100ml per nozzle Repeat the process for all the nozzles. (Beam, RCC wall and columns) complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for providing and applying structural grade EPIBOND-21-LP prior to application of any type of mortar plaster confirming to ASTM-C-882-91 (Arizona slant shear test) to ensure bond between old concrete and new concrete complete all as per manufacturer's instructions complete all as specified as directed by Engineer-in-charge. Make :- Krishna Conchem, Dr Fixit, Fosroc as approved by GE.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for building up the profile of structural member by using latex additives (MONOBOND) modified air cured motor system (Polymer modified motor/LW+) (1:5:15 = 1 monobond-5 cement -15 sand) -in damaged area in 30mm thickness including leveling profiling etc complete all as per manufacturer's instructions complete all as specified as directed by Engineer-in-charge. Make :- Dr Fixit, Sita, STP, Fosroc as approved by GE.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for providing and applying jacketing around columns with Micro concrete (Molith-MC) M40 including all lifts, shuttering, drilling holes and fixing shear anchor as per specification complete. Note :- Reinforcement shall be measured and paid separately rates quoted shall be inclusive of jacketing, formwork and micro concrete etc complete all as specified as directed by Engineer-in-charge. Make :- Dr Fixit, STP, Fosroc as approved by GE.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for rendering 15mm thick cement plaster in CM 1:4 on fair faces of brick work/concrete surfaces finished even and smooth without using extra cement by using synthetic fibre additives of recorn @ 125gms per bag cement mixed with WPC @2% by weight of cement complete all as specified as directed by Engineer-in-charge. Note :- WPC and synthetic fibre additives of recron shall be meaasured and paid seperately.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for rendering 20mm thick cement plaster in CM 1:4 on fair faces of brick work/concrete surfaces finished even and smooth without using extra cement by using synthetic fibre additives of recorn @ 125gms per bag cement mixed with WPC @2% by weight of cement. (WPC and synthetic fibre additives of recron shall be meaasured and paid seperately) complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material & labour for preparation of newly plastered wall surfaces, over 10cm girth & applying two coats of water proof paint (rain coat of Dr. fixit or equivalent in STP, Fosroc, Krishna as approved) over a coat of Dr. Fixit primeseal or equivalent in STP, Fosroc, Krishna as approved or wall primer complete all as specified and as per manufacturer's instruction complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for rendering 15mm thick cement plaster in CM 1:6 on fair faces of brick work/concrete surfaces finished even and smooth without using extra cement complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for rendering 15mm thick cement plaster in CM 1:6 on fair faces of brick work/concrete surfaces finished even and smooth without using extra cement by using WPC @2% by weight of cement. (WPC shall be meaasured and paid seperately) complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for rendering 10mm thick on fair faces of ceilings in CM (1:3) & rendering is to be finishing even & smooth without using extra cement., complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for preparation of new plastered surface of wall and applying 2 coats of oil emuslion distemper over a coat of 1 to 2 mm thick wall care putty (JK / Birla or equivalent)complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for preparation of new plastered surface of ceiling and applying two coats of oil emuslion distemper over a coat of 1 to 2 mm thick wall care putty (JK / Birla or equivalent) complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for preparation of old plastered surface of ceiling and applying 2 coats of oil emuslion distemper over a coat of 1 to 2 mm thick wall care putty (JK / Birla or equivalent) complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for preparation of old plastered surface of wall and applying 2 coats of oil emuslion distemper over a coat of 1 to 2 mm thick wall care putty (JK / Birla or equivalent) complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixing for MS framed works as in grills, railings, brackets for chajjas etc, conforming to FE-290 Gde E-165 complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixing for pre-painted Galvalume Aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for excavating in post holes (or similar holes) each n.exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm in hard / dense soil or in cement concrete, complete all as specified as directed by Engineer-in-charge.
Supply & Fixing rolled sections as in main & cross beams , columns, hip and jack rafters , purlins where connected to common rafters and running rails & any other places with angles cleats ot other connected plates confirming to Fe 410 -W (Gde-E-250) quality A, complete all as specified as directed by Engineer-in-charge.
Supply & Fixing plates (plain or chequered ) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attahment, confirming to Fe 410 -W (Gde-E-250) quality A, complete all as specified as directed by Engineer-in-charge.
Taking down soil, rain water pipes (any size or pattern), including all fittings, heads,shoes,bends, swan-neck, etc. Including cleaning or refixing or removal to store ( measured over all as fixed along the center line over fittings and accessories) complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixing 110 mm dia PVC (SWR) grade pipes, single socketed in any length with rubber ring joints fixed to walls / laid in trenches with and including fixing clip complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fix in repairs110 mm dia PVC (SWR) grade single T/Y, etc, with access doors including fixing clips complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixing in repairs 110 mm dia bore PVC (SWR) bends any radius complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixing 160mm dia PVC (SWR) grade pipes, single socketed in any length with rubber ring joints fixed to walls with and including fixing clips complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixing in repairs 160mm dia PVC (SWR) grade single T/Y, etc, with access doors including fixing clips complete all as specified as directed by Engineer-in-charge.
Supply and fixing in repairs 160mm dia PVC (SWR) bends any radius from 5th floor and above complete all as specified as directed by Engineer-in-charge.
Supply & Fixing 100 mm bore of sand cast CI soil waste pipe in any length with ears and jointed with neat cement paste fixed to wall complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing 75mm bore of sand cast CI soil waste pipe in any length with ears and jointed with neat cement paste fixed to wall complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour in repair 75mm cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) including grating jalli complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing 75mm sand cast CI Branch pieces (Tee), Single (equal), ordinary or inverted (spigot or socket type) or with parallel branches with ovel access door and jointed with neat cement paste to CI pipes fixed to wall or roof at any floor/ any height/ any location including all fittings complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing 100mm sand cast CI Branch pieces (Tee), Single (equal), ordinary or inverted (spigot or socket type) or with parallel branches with ovel access door and jointed with neat cement paste to CI pipes fixed to wall ,complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing in repair 100mm CI ‘P’ or ‘S’ Traps jointed with neat cement paste fixed to wall or roof at any floor/ any height/ any location including all fittings complete all as specified and as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing in repair cast iron cowl suitable for 75mm dia pipe , complete all as specified as directed by Engineer-in-charge.
Height from 5th floor and above
Supply & Fixing in repair cast iron cowl suitable for 100mm dia pipe,complete all as specified as directed by Engineer-in-charge.
Height from 5th floor and above
Supply & Fixing in repair stack clamps suitable for securing 100mm dia CI pipe made out of 50mm by 5mm flat iron and 16mm dia round iron stays Including bolts and nuts and securing ends of stays fixed to wall, complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing stack clamps suitable for securing 75mm dia CI pipe made out of 50mm by 5mm flat iron and 16mm dia round iron stays Including bolts and nuts and securing ends of stays fixed to wall,complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing, complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing, complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Taking up or down 25mm bore steel tubing and connections, including cleaning for refixing, complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Taking up or down 50mm bore steel tubing and connections, including cleaning for refixing,complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing 15mm bore steel water tubes, medium grade, galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors,complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing 20mm bore steel water tubes, medium grade, galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors , complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixing 25mm bore steel water tubes, medium grade, galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixing 50mm bore steel water tubes, medium grade, galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixing in repairs CP Pillar taps 15 mm dia, cast copper alloy , with capstan heads, chromium plated , screwed down high pressure ,with long screwed shanks and fly-nuts , screwed for iron pipe and fixedcomplete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixing in repairs fancy type bib taps, chromium plated cast copper alloy 15mm bore with crutch handle, screwed down, & fixed complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixing in repairs stop valve fancy type chromium plated screwed down, high presure with butterfly handle screwed both ends for pipe and fixed to pipe of 15mm dia bore complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixing in repairs stop valves fancy type chromium plasted with long shank and cup (concealed type) 15 mm dia screwed down, high pressure with crutch or butter fly handle, screwed both ends, complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixing 20 mm bore Stop valves , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unionSupply and fixing ixed as in repairs complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixingin repairs Vitreous China wash down water closet pan ( pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing in repairs, Plastic water closet seat, black or white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing in repair vitreous china squatting pan Orissa pattern long pan size 510 x 410 x 260 mm with CI trap 100mm with integral foot rest & fixing incl but (excluding flushing cistern and flush pipe) making good floor to match complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing as in repair Vitreous china wash basin counter type , white , flat back, size 550 x 400mm including brackets and 32mm waste cupling, complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing as in repairs Vitreous China urinal, Half stall type white , complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing as in repair vitreous china urinal partition white of size 310 x 700mm, complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing in repairs PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing in repairs PVC valveless syphonic action type, flushing cistern Low level white, with inlet ball valve , float and handle 10 Ltr capacity including brackets complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing in repairs Flush pipe of Polyethylene of low or high density or PVC 32 mm dia. for low level cistern complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing in repairs Chromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing in repairs Soap dish, vitreous china white approximate size 160 x 160 x 90mm, complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing in repairs aluminium anodised tubular towel rail 20mm dia, D type 600mm long between flanges,complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing in repairs low density polyethylene pipes (LDPE) of pressure rating 6 kg/cm2 fixed complete to walls, ceilings or in floors etc for outlet of washing machine/wash basin etc of 40 mm dia bore complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing 2000 lit capacity rotational moulded polyethylene water storage tanks (cylindrical, vertical with closed top ) hoisted and fixed position all specified in SSR Part-I, with and including 20mm dia ball valve, high pressure of PTMT, with epoxy coated aluminium rod & high density plastic ball, minimum weight 210gm, screwed for iron pipes and fixed; including disconnecting and dismantling/ taking down of existing old unserviceable water storage tank above 5th floor terrace, complete all as specified and directed by Engineer-in-Charge.
Supply & Fixing Gun-metal, globe or gate valves 50mm bore dia., with iron wheel head, screwed both ends for iron pipe and fixed above 5th floor terrace complete all as specified as directed by Engineer-in-charge.
Demolition of Cement concrete in any description and in any position not other wise specifically provided on terrace of bldg ( above 5th floor) complete all as specified as directed by Engineer-in-charge. and removal of debris to out side MD land as per guidelines of BMC.
Material and labour for cement concrete 1:2:4 type B-2 (40mm graded stone aggregate) by using WPC @ 2% of weight of cement as in floor of RCC roof ( above 5th floor) complete all as specified as directed by Engineer-in-charge. Note: WPC shall be paid seperately.
Demolition of existing treatment of any type and preparing the surface by cleaning the concrete surface with wire brush and a high pressure water jet and ensure that it is free of dust, oil grease, loose particles vegetation roots etc and filling crackswith polymer modifed mortar using smartcare RP or Epoxy mortar including material and labour for laying padding cement concrete in terrace 1:2:4 type B-0 (using graded stone aggregate) of 50mm average thickness maintaining 1:30 slope finishing with 10 mm thick cement mortar 1:3 and providing High performance hybrid polyurea elastomeric waterproofing spray applied SmartCare Hypertron Hybrid liquid membrane with an elongation of 600% and tensile strength of more than 13 N/mm2 as per ISO 527 type 5 , shore A Hardness of min. 85 as per ISO 868, and crack bridging ability of 3.5 mm as per ASTM C1305. The system includes final base preparation, epoxy primer application and applying SmartCare Hypertron Hybrid or approved equivalent in two coats with a consumption of 2kg/sqmt, etc., complete as per Manufacturere specifications complete all as specified as directed by Engineer-in-charge.
Material and labour for cement 1:2:4 type B-0 (12.5mm graded stone aggregate) as in roof kerbs and leveling course on RCC roof surfaces ( Terrace above 5th floor of bldg.) complete all as specified as directed by Engineer-in-charge.
Material and labour for brick work with sub class "B" bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4), complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4), complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Removal of tree roots and branches spreed over stone wall/brick wall joints, injecting anti vegetation chemical and making good the stone/ brick wall joints by flush pointing in CM (1:4) including provision of necessary scafolding and removing the debris outside MD land complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour PCC 1:7:12 with brick aggregate as in lean concrete/filling concrete complete & including scaffolding upto 5th floor of building complete all as specified as directed by Engineer-in-charge.
Treatment of sunken floor slab comprising of the following specifications and all as specified :- (i) Material & labour for cleaning the sunken/lowered portion of RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely 40 mm thick avg PCC (1:2:4) type B-0 using 12.5mm graded aggregate as in padding concrete to achieve proper slope including cutting holes in bricks or RCC wall for spout (Cost of cutting holes and pipes shall be measured and paid separately) (ii) Rendering of uneven surfaces with 6mm thick CM (1:4) mixed with integral water proofing compound @ 3% by wt of cement consumed. Fill it with water and check dampness and seepage. Where dampness/seepage is noticed, nozzles shall be fixed and grouting to be carried out. (WPC shall be measured & paid separately) (iii) All junctions points of side wall where CI/GI pipes are passing through shall be sealed with epoxy putty. (iv) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean.
(v) Material & labour for applying two coats of polymer modified cementious water proof coating as per manufacturs instruction to bottom and vertical sides up to finished floor level+100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion all as specified and directed.(This item shall be measured and paid separately) Note :- Test the water proofed area (ponding test) by filling water for at least 72 hours and shall be tested for leakage seepage and to the entire satisfaction of GE. Test shall be done in presence of reps of PMG and record for each sunken slab shall be maintained. The treatment shall be carried out by authorised applicators of chemicals. Cost of testing shall be deemed to be included in the rates quoted above. (vi) All pipes laid in sunken portion shall be covered with 50mm thick PCC (1:3:6) all round after painting with anticorrosive paint (This shall be measure & paid separetely).
Height upto and including 4th floor
Height from 5th floor and above
Cutting holes in bricks walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 exceeding half brick wall but n.exc one brick, complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material & labour for applying two coats of polymer modified cementious water proof coating as per manufacturs instruction to bottom and vertical sides up to finished floor level + 100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portioncomplete all as specified as directed by Engineer-in-charge. Make :- Dr Fixit, Fosroc, STP as approved by GE.
Height upto and including 4th floor
Height from 5th floor and above
Material & labour for PCC (1:7:12) with brick agg as in lean concrete/filling concrete etc complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material & labour for water proofing plaster for sunken portion in CM (1:3), 15 mm thick in two coats using Pidiproof LW+ water proofing chemical of Dr. Fixit or equivalent in STP, Fosroc as per manufacturer's instruction and finishing the surface even and smooth without using extra cement complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material & labour for water proofing treatment of sunken floor/wall surfaces by applying two coats of water proofing chemical and cement mix in ratio (1:1.5), (PIDICRETE UPR or equivalent approved water proofing chemicals), complete all as per manufacture's instructionscomplete all as specified as directed by Engineer-in-charge. Make : Dr. FIXIT, Chemisol, Choksy Chemicals as approved
Height upto and including 4th floor
Height from 5th floor and above
Taking down chowkats or frames but n exc 1.5 sqm each but with shutters (without taking off shutters from the frame) complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Taking down chowkats or frames but exc 1.5 sqm each but n.exc 4 sqm with shutters (without taking off shutters from the frame) complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing powder coated (colour of coating as directed) aluminium (minimum 25 micron thickness of coating) of various section as required/suitable for doors, window & partion/Ventilator (sliding /or openable type)etc including fixing and making the frames hinges to receive glass/wire gauge etc. Complete incl all fittings like jointing cleats, glazing clips, rubber neoprene packing. anodised aluminium snap beading screws etc. rubber beading, clips locking arrangement, handle, sealant etc complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & fix 6mm thick bakelite sheet with decoratve choice lamination on both sides complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & fix aluminium anodised grill (minimum thickness of anodising 15 micron) with and including suitable aluminium anodized 'E'/'H' section frame as required with aluminium rebated/screwed attachment complete all as specified as directed by Engineer-in-charge.. Note:- Aluminium grill shall be of Deco grill of M/s ELESAR FOCCHI Ltd as per Design No DG 102, 7.50mm x 6.0mm and weight shall not be less than 3.131Kg/Sqm or approved design
Height upto and including 4th floor
Height from 5th floor and above
Height upto and including 4th floor
Height from 5th floor and above
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixingsolid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixingfactory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement forstyle and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site.complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixing in repairs 18/19 mm thick Prelaminated partical board interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work including 6 mm thick teak wood beading all around complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixing in repairs 12 mm thick Prelaminated partical board interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work including 6 mm thick teak wood beading all around complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour 2nd class HW Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing 30mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing 30mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats , complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fixingfor aluminium anodized barrel tower bolts 150 mm size of extruded section and fixed.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing 150 mm size aluminium alloy handles, cast type anodised, ISI marked all as specified.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing butt hinges 100 mm stainless steel hinges medium weight and fixed.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing 125 mm long hasp and staple safety type aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing for aluminium anodized barrel tower bolts 200mm of extruded section and fixed complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing 200 mm size aluminium alloy handles, cast type anodised, ISI marked complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Preparation of new wooden surafces & apply two coats of synthetic enemal paint over a coat of pink primer, complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for machine cut cudappa stone slab 20-25 mm thick laid over screed base in cement and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishingcomplete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour Granite (of any type) work (table rubbed and polished) 20mm thick in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite., and nosing /rounding to edges of stone slabs one edge,complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Preparation of new steel surafces & apply two coats of synthetic enemal paint over a coat of red oxide,complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply only Integral water proofing compound
Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar, complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for 25mm thick PCC (1:2:4) type B-1 using 20mm graded stone aggregates as in flooring finished even & rough to receive the bedding mortar complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Dismantling floor hearth or wall tiling including cement mortar bedding removing serviceble tiles to store and rubbish off the permises.complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour Non - skid Ceramic tiles coloured 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM (1:4), complete all as specified. complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour Glazed ceramic tiles coloured of size 450 x 300 X 6 to 7mm thick laid on vertical surface such as dado/skirting over cement mortar backing coat, set jointed in neat cement slurry and pointed in white or coloured cement including 15mm thick backing coat in CM 1:4 , complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for machine cut kota stone slab flooring 20-25mm thick over cement screed bed in CM (1:4) 15mm thick, & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for machine cut kota stone slab flooring 20-25mm thick in riser / treads of steps in single piece, skirting, dado and pillar laid over cement screed and jointed withover cement screed bed in CM (1:4) 15mm thick, & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for rounding to edges of stone slabs, such as in steps, cooking platform, and other similar situations, complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Material and labour for plain cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in floor or paving 75 mm thick and finished even and smooth without using extra cement, as in plinth protection complete all as specified as directed by Engineer-in-charge.
Material and labour for forming construction joint 50mm deep x 10mm wide filled with sealing compound Grade 'A' in plinth protection, complete all as specified as directed by Engineer-in-charge.
Material and labour for plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in floors, complete all as specified as directed by Engineer-in-charge.
Material and labour for fixing in repairs machine pressed pre cast concrete interlocking tiles of any shape & size confirming to IS 15658-2006 of 60mm thickness, M-35 graded with grey cement & pigment,( design pattern & colour as approved) complete all as specified as directed by Engineer-in-charge.
Material and labour for sand filling under floors or in foundation including watering and consolidation etc.,complete all as specified as directed by Engineer-in-charge.
Supply and fixingin repairs fancy type drapery rods, powder coated aluminium of 20-25mm size incl brackets complete all as specified as directed by Engineer-in-charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply & Fixing in repairs door closer aluminium (Die cast) body hydraulically regulated, designation No 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 Kg and fixed complete all as specified as directed by Engineer-in-charge.
Supply & Fixing 250 lit capacity water storage tanks (rectangular, vertical with closed top ) hoisted and fixed position all specified in SSR Part-I, with and including 20mm dia ball valve, high pressure of brass (make Kohinor), with epoxy coated aluminium rod & high density plastic ball, minimum weight 210gm, screwed for iron pipes and fixed including dismantling water tanks, complete all as specified and directed by Engineer-in-Charge.
Height upto and including 4th floor
Height from 5th floor and above
Supply and fix false ceiling with powder coated exposed GI grip suspension system (E-grip T-2430 or equivalent load carrying capacity with mid span deflection not exceeding. 1/360 span with hanger spacing of 1200mm c/c) consisting of main runner 3600mm long, cross tee 1200mm/600mm long wall angle. The main runners to be placed @ 1200mm, the cross tee 1200mm will be inserted in the pre cut slots of main runner at a regular interval of 600mm from a modular grid of 1200mm x 600m. Additinoal cross tees of 600mm shall be placed perpedicular to the cross tee 1200mm long to finally form a grip of 600mm x 600mm. Grip of modular size 600mm x 600mm shall be supported by 6mm dia GI wire from purlins / soffit with and including 6mm thick high pressure steam cured non asbestos fiber and fixed as in repairscomplete all as specified as directed by Engineer-in-charge.
Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/ dense soil complete all as specified as directed by Engineer-in-charge.
All as per item no 133 above but exc 1.5 m depth and n.exc 3.00 m depth-
Supply and fixingfor 200mm bore RCC pipe class NP-2 laid and jointed complete with collers as specified including testing all as specified and directed by Engineer-in-Charge.
Material and labour for cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in bed to drain pipes including forming cradle after they are laid and tested for 200mm bore RCC pipe complete all as specified and as directed by Engineer-in-Charge.
Material and labour for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundations, filling ad mass concrete complete all as specified as directed by Engineer-in-charge.
Material and labour for cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in benching, coping, cills steps, parapets, railings up to 60cm in height, water troughs and the like rounded or chamfered on edges including necessary form work complete all as specified as directed by Engineer-in-charge.
Material and labour, Extra for forming fair finished drain or channel 200mm inner girth in cement concrete, using ex-tra cement, including forms, moulds, mi-tred/stopped ends etc complete all as specified as directed by Engineer-in-charge.
Cutting into existing manholes for connecting new drain making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 Sec) in cement concrete 1:2;4 type BI smooth finished and reforming benching as reqd for 200mm bore of pipe complete all as specified as directed by Engineer-in-charge.
Removal of excavated soils from site to distance exc1.50 Km but not exc 5 Km and depositing where directed , complete all as specified as directed by Engineer-in-charge.
Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. in Hard / dense soil, complete all as specified as directed by Engineer-in-charge.
M&L for colured vetrified Ceramic double charged tiles 10mm thick, area of each tiles not exceeding 0.36 Sqm in floors etc. Set and joined in neat cement slurry and pointed in white or colured cement to match over 15mm thick screed bed in CM (1:4) complete all as specified as directed by Engineer-in-charge.
Height Upto and including 4th floor
Height from 5th floor and above
M&L for colured vetrified Ceramic double charged tiles 10mm thick, area of each tiles not exceeding 0.36 Sqm as in skirting etc.and set and joined in neat cement slurry and pointed in white or colured cement to match over 10mm thick backing coat in CM (1:4) complete all as specified as directed by Engineer-in-charge.
Height Upto and including 4th floor
Height from 5th floor and above
Supply and fixing for pre-painted Galvalume Aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Map as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified as directed by Engineer-in-charge.
Height Upto and including 4th floor
Height from 5th floor and above
Taking down carefully aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators sockets etc to be measured separately) and making good disturbed surfaces of walls, floors, etc.complete all as specified as directed by Engineer-in-charge.
Material and Labour for point wiring concealed complete with 1.5 sqmm single core multistranded FRLS PVC insulated unsheathed copper conductors 1100 volts grade drawn through and including PVC pipe of size not less than 20 / 25 mm dia including PVC bend, tee joints etc as per site requirement , ISI marked with accessories fixed on wall/ceiling/truss etc with PVC non metallic ISI marked terminal boxes/ modular boxes surfacing on wall including one FRLS PVC insulated & sheathed multistranded green colour copper conductor 1.5 sqmm as earth continuity conductor connected to common earth as earth dolly for :-
One light point controlled by one switch SP one way.
One ceiling fan point controlled with one 5A switch
One exhaust fan point controlled with one 5A switch
One 3 pin socket outlet 5Amps on independant board.
One 3 pin socket outlet 5Amps on same board with other switches.
One 3 pin socket outlet 15 Amps on same board with other switches.
Material and Labour point wiring for Geyser /AC complete with 4 sqmm single core multistranded FRLS PVC insulated unsheathed copper conductors 1100 volts grade drawn through and including PVC pipe of size not less than 20 / 25 mm dia including PVC bend, tee joints etc as per site requirement, ISI marked with accessories fixed on wall/ceiling/truss etc with PVC non metallic ISI marked terminal boxes / modular boxes surfacing on wall including one FRLS PVC insulated & unsheathed multistranded green colour copper conductor 4 sqmm as earth continuity conductor connected to common earth as earth dolly complete all as specified as directed by Engineer-in-charge.
Material and Labour point wiring for 15 Amps socket complete with 2.5 sqmm single core multistranded FRLS PVC insulated unsheathed copper conductors 1100 volts grade drawn through and including PVC pipe of size not less than 20 / 25 mm dia including PVC bend, tee joints etc as per site requirement, ISI marked with accessories fixed on wall/ceiling/truss etc with PVC non metallic ISI marked terminal boxes / modular boxes surfacing on wall including one FRLS PVC insulated & unsheathed multistranded green colour copper conductor 4 sqmm as earth continuity conductor connected to common earth as earth dolly complete all as specified as directed by Engineer-in-charge.
Supply and fix Modular Switch, 6Amp, One way, 1 module. complete all as specified as directed by Engineer-in-charge. Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (NIXON)
Supply and fix Modular Switch, 16Amp, One way, 1 module complete all as specified as directed by Engineer-in-charge. Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (NIXON).
Supply and fix support function blank plate single, 1 module complete all as specified as directed by Engineer-in-charge.
Supply and fix Modular type, electronic fan regulator (5 step), 450 Watts, 230 volts, 2 module complete all as specified as directed by Engineer-in-charge. Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (NIXON).
Supply and fix ceiling rose surface bakelite with ISI mark, flush type with ISI mark three terminals complete all as specified as directed by Engineer-in-charge.
Supply and fix Modular switch Socket oulet, 6 Amps, 2/3 pin combined, 2 module complete all as specified as directed by Engineer-in-charge. Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (NIXON).
Supply and fix Modular Socket oulet only , 6/16 Amps, 2/3 pin , 2 module complete all as specified and directed Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (NIXON).
Supply and fix Modular white cover plate with Frame 2 Module complete all as specified and directed. Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (WEGA)
Supply and fix Modular white cover plate with Frame 3 Module complete all as specified and directed. Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (WEGA)
Supply and fix Modular white cover plate with Frame 4 Module complete all as specified and directed. Make : Legrand(Arteor), Havells(Coral) , Anchor(Ave) .
Supply and fix Modular white cover plate with Frame 6 Module complete all as specified and directed. Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (WEGA)
Supply and fix Modular white cover plate with Frame 8 Module complete all as specified and directed. Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (WEGA)
Supply and fix Modular white cover plate with Frame 12 Module complete all as specified and directed. Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (WEGA)
Supply and fix Modular metal flush box 2 module including cutting and chassing complete all as specified and directed. Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (WEGA)
Supply and fix Modular metal flush box 3 module including cutting and chassing complete all as specified and directed Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (WEGA)
Supply and fix Modular metal flush box 4 module including cutting and chassing complete all as specified and directed Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (WEGA)
Supply and fix Modular metal flush box 6 module including cutting and chassing complete all as specified and directed.Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (WEGA)
Supply and fix Modular metal flush box 8 module complete all as specified and directed Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (WEGA)
Supply and fix Modular metal flush box 12 module including cutting and chassing complete all as specified and directed. Make : Legrand (Arteor)/Havells (Coral)/Gold Medal Electrical Pvt Ltd (WEGA)
Supply and fix baton intergrated LED channel 1x20WH accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed . Make : Havells/Philips/Jaquar
Supply & Fixing Ceiling light 36 WATT-2ft X 2 ft Recess mounting led ultra slimceiling light with extruded aluminium housing and milky diffuser.LED ultra slim panel complete all as specified as directed by Engineer-in-charge. Make : Havells/Philips/Jaquar
Supply & Fixing baton intergrated LED channel 1x10 WH accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Make : Havells/Philips/Jaquar
Supply & Fixing Plug and Socket enclosure, in sheet metal enclosure with MCB, SP 20 Amps 240 Volts complete with metal clad socket for window type air conditioners complete all as specified as directed by Engineer-in-charge. Make : Javells/L^T/Legrand/Seimons
Taking down old unserviceable submain cable of any size and capacity and finishing wall surfaces complete all as specified as directed by Engineer-in-charge.
Supply and fix submain wiring in repair with two single core FRLS unsheathed 1100 volts grade cable with stranded copper conductor of size 4 Sqmm in and including PVC conduit of suitable dia, concealed ISI marked including 1 single core cable with stranded copper conductor of size 4 sqmm (green colour) for earthing. Make : Polycab, Havells, Plaza, Note :- (i) Two runs of 4Sqmm cable, 1 run of PVC conduit and 1 run of 4 Sqmm cable shall be measured as 1 RM. (ii) Each submain wiring shall run in seperate PVC conduit.
Supply and fix submain wiring in repair 2 single core FRLS unsheathed 1100 volts grade cable with stranded copper conductor of size 10 Sqmm in and including PVC conduit of suitable dia, ISI marked including 1 single core cable with stranded copper conductor of size 10 sqmm (green colour) for earthing. Make : Polycab, Havells, Plaza, Note :- (i) Two runs of 10 Sqmm cable, 1 run of PVC casing caping and 1 run of 10 Sqmm cable shall be measured as 1 RM. (ii) Each submain wiring shall run in seperate PVC conduit
Supply & Fixing sheet metal enclosure 12 way Double door type having protection IP-42, with 200 Amps rated bus bar connecting with existing wiring circuits by providing copper pin terminals of suitable size complete all as specified as directed by Engr-in-charge comprising of the following :- Make: Strandred/ Legrand / L &T/Havells / Schinder (a) MCB SPN 63 Amps, 240 Volts - 01 No Make - Legrand Schneider / Havells/ L &T/ Strandered (b) MCB SP 6-32 Amps, 240 Volts - 10 Nos Make - Legrand / Standard/ Havells / L & T
Supply and fix , testing and commissioning of storage type water heater (geyser) vertical type of 25 Ltrs capacity , single phase, vertical type, Rust Resistant, ABS made with thermal cut off with power consumption 1500 watts, ISI marked, BEE 5 star rating including fixing on wall with chroumium plated screws & nut bolts , connection to water pipe line and electric connection complete all as specifed and directed by Engineer-in-charge. Make- Havells/ Jaquar / Philips/ Racold Note:- (a) Taking down U/S geyser of any capacity will be deposited in MES store yard
Material and labour for cleaning all dust filling cavities with filler, prepartation of surfaces, painting of ceiling fans any type /any site in situ with one coat of synthetic enamel paint by spray painting complete all as specified as directed by Engineer-in-charge. Make : Asian Apoclite, Berger, Nerolac Hi Gloss
Material and labour for cleaning all dust filling cavities with filler, prepartation of surfaces, painting of Exhaust fan any type/any site in situ with one coat of synthetic enamel paint by spray painting complete all as specified as directed by Engineer-in-charge. Make : Asian Apoclite, Berger, Nerolac Hi Gloss
Material and labour for rewinding of unserviceable ceiling fans lof size 1200/1400 sweep with approved copper enamalled wire of suitable guage, varnishing, replacing existing split/ quarter pins, rubber bush, capacitor 2.5 Mfd and including taking down and refixing in exsiting position and testing complete all as specified and directed by Engr in charge.
Material and labour for rewinding of unserviceable exhaust fans of size 225/300/450/630mm sweep with approved copper enamalled wire of suitable guage, varnishing, replacing existing nut bolts pins, rubber bush, capacitor , bearing ,m bush, frastner etc and including taking down and refixing in exsiting position and testing complete all as specified and directed by Engr in charge.
Supply and fix decorative 9 watt wall light fitting internally pre wired and including connecting up with twin core twisted copper conductor cable with suitable size complete all as specified as directed by Engineer-in-charge. Make : Havells/ phillips/ Jaquar
Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick ,buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth strip 32 x 6 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion.
Supply & Fix Factory fabricated MS fire cabinet box as per give design made out flat CRCA of appropriate size and thickness all as directed including two coat of powder coated approved colour synthetic enamel paint over a coat of red oxide primer & fixed on wall with necessary nuts/bolts or welding to existing MS pipe by supporting angle complete all as specified & directed by Engineer-in-Charge.
Supply & Fixing canvas fire hose 63mm dia bore 30metre long confirming to IS Having male/female brass coupling both end complete all as specified as directed by Engineer-in-charge.
Supply &Fixing brass Nozzle 25 mm bore suitable for 63mm dia canvas pipe complete all as specified as directed by Engineer-in-charge.
Supply & Fixing rubber fire pipe with drum and nozzle 25 mm dia bore 30 metre long confirming to IS marked fixed to wall mounted angle iron frame complete all as specified as directed by Engineer-in-charge.
Taking out fire rubber pipe drum with frame and frame fix to new locatioin with anchor fastner / nut bolt as per site requirement and complete all as specified as directed by Engineer-in-charge.
Garima Construction Co
ASHOK CONSTRUCTION
M/s S.D Construction Co
AGRAWAL ASSOCIATES
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .