General Repairs with replacement of defective parts and complete service of Divisional Truck bearing Registration No. JK02AR-1620 under M and R

Amount

Repairs to Steering:- Repairs to steering of the vehicle by way of dismantling/removing of steering from the vehicle and then providing/fitting of new parts in place of old i.e. steering tie rod assy. 01 set, steering UJ cross-01 No, Steering kit-01 kit, split pin-02 nos, spindle pin-02 nos. Steering/TQ oil-2 ltrs and setting up and checking. The job includes cost of material, labour charges and taxes.

Repairs to Silencer:- Repairs to Silencers of the vehicle by way of removal damaged silencer and exhaust pipe and P/F of silencer with pipe, gasket, flange nut/bolt- 02 nos., clamp with nut/bolt-02 Nos. assembling of exhaust system, including all allied works. The job includes cost of material, labour charges and taxes.

Repairs to Clutch assembly system:- P/F of spares/material in place of defective/worn out of vehicle by way of dismantling of clutch system with P/F of new parts i.e. Pressure plate-01 No, Clutch Plate-01 No. Clutch release bearing-01 No. Face Plate-01 clutch release fork-01 No. Shaft bolt-04 Nos. The job includes cost of material, labour charges and taxes.

Repairs to Propeller shaft:- Repair to the Transmission system of the vehicle by way of dismounting of propeller shaft ad removal of defective/damaged parts. Providing and fitting of Centre Bearing-01 Nos. Half Yoke-01 Nos, cross Holder-02 Nos. Centre Bearing Coupling-01 No. Coupling nuts & bolts-4 Nos. Assembling of propeller shaft and all allied works, checking of alignment complete job includes the cost of material, labour charges and taxes.

Repair to Tie rod end and King pin assy: P/F of new parts in place of defective parts/worn out parts i.e. King pin-02 Nos. king pin bush-01 set. Thrust washer upper and lower-01 No. each, thrust bearing-01 No. cotter kit-01 No. spacer-01 No. shims-02 No, king pin repair kit-01 No., tie rod end small-01 set, tie rod end big-01 set. After repair complete testing and wheel alignments. The job includes cost of material, labour charges and taxes.

Repairs to Radiator:- Repair to the Radiator of the vehicle by way of dismantling it from the vehicle, repair to fins, tubes and then joining the cracked corners by binding solution to prevent leakage and fitting of the same to the vehicle after cleanings and testing and also P/F of temperature meter-1 No. thermostat valve -01 No, Hose pipe-01 set, coolnt-4 ltrs. The job includes cost of material, labour charges and taxes.

M oil Change:- Periodical maintenance of Departmental vehicle by way of flushing old engine oil from the vehicle and filling with fresh Engine oil-18 ltrs. M oil filter-01 No. Diesel filter-01 No..The job includes cost of material, labour charges and taxes.

Repairs to Differential: Repair to the Differential of the vehicle by way of dismantling it and extracting of defective parts, cleaning, inspecting, P/F of new parts in place of defective parts, crown wheel+ pinion-01 set, pinion star set-01 set, differential bearing -02 No differential side bearing-01 No. pinion oil seal- 1 No. differential joint-01 No. crown washers-02 No., chuck nut-02 No, Differential oil-2.5 ltrs. (Topping) job also includes repair to rear axles cutting & welding of axles to axle shaft, Assembling of system and all allied works, complete job includes cost of material, labour charges and taxes

Repairs to Electrical system: Repairs to wiring of the vehicle by way of replacement of old / defective /burnt out wiring with new wiring for the vehicle, this also includes replacement of the complete fuse box of the vehicle and P/F of new head lights for the vehicle and testing the complete new circuit on load so as to ensure proper functioning of the auto-electric circuit of the vehicle. Job includes cost of material, labour charges and taxes.

Repairs to Front and Rear Leaf Spring:- Repairs to front and rear leaf spring assembly by way of dismantling and removing of damaged items and P/F of new items in place defective items i.e. Rear leaf spring main R/H-01 No, Rear leaf spring R/H 2nd – 01no, Rear leaf spring R/H 4th – 01 no, front leaf spring R/H main-01 no, front leaf spring R/H 4th -01 no, centre bolt front-01 nos, centre bolt rear-01 no. leaf spring bush-06 nos, leaf spring pin-06 nos, spring shackle assy front-02 no, Spring shackle assy rea-02 no, U clamp small -06 nos, with nut and bolts. U clamp Big-04 Nos with nut and bolts, Grease nipple-03 no and washers-04 nos. The job also optimum curvature and assembling, fitting and alignment of front and rear leaf spring assy, and all other allied works. The job includes cost of material, labour charges and taxes.

Speed__________ also P/F

M/s Nanda Auto works (BID ID -2350191)

N B Engineering and Electric Works (BID ID -2350220)