Upgradation and Beautification of Road from Bus Stand to Govt. Circuit House, Nani Daman. (5th call) (E-23734)

Amount

Civil work

Clearing and grubbing road land including uprooting rank vegetation grass bushes,shrubs,sapling and trees girth up to 300 mm removal of stumps of trees cut earlier and disposal of unserviceable materials (C) By mechanical means in area of light jungle

Scarifying gravelled macadam or bitumen macadam surface 6 cm to 10 cm.depth including stacking useful materials on road side and disposing off remaining stuff. For removing bitumenous surface layers from bitumen road

Demolition including stacking of serviceable materials and disposal or unserviceable materials at nonobjectionable place with all leads and lifts including cutting the reinforcement, and finishing the broken surfaces to match with the surroundings etc. complete : RCC Works

Demolition including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift. (i) P.C.C. work/ Road Works

Demolition of Brick Work/AAC block work with plastered surface/ wall dedo including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift.

Dismentaling tiled of stone floors laid in mortar including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift. Also for stone floor, chinamosaic floor, tile dedo, etc.

Dismentling steel work including distempering and stacking the materials with all lead and lift.

Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 60 cm girth upto and including 120 cm girth

Taking out existing kerb stones of all types from footpath/ central verge, including removal of mortar etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.

Dismentling/ removal Charges of existing LED Street Light/ telephone Fixtures/ Traffic Signals of various wattages with Bracket & Street Light Pole including excavation and dismantling of foundation concrete and lines,carring & handling charge for shifting under the supervision of concerned department, to proper place as specified and directed by the dept. disposal with all lifts and up to all lead and lift, stacking the serviceable and unserviceable material separately.

Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material with all lead and lift, as per direction of Engineer-in-Charge.

Dismantling of manhole including R.C.C. top slab, C.I. cover with frame, including stacking of useful materials near the site and disposal of unserviceable materials with all lead and lift as per direction of Engineer-in-charge. Max. size 120x90x90 cm deep.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing material and labour, machinery for Excavation of foundation/utilities upto 1.5 m depth including sorting out and stacking of useful materials and disposing off the excavated stuff within the site for all lead, all lift/ depth (excluding hard rock and black cotton soil) anywhere from the site etc complete as directed by Engineer in charge. - Any type of soil or rock not requiring Blasting.

Providing material and labour for Excavation of foundation/utilities from 1.5 mt to 3.0 mt depth including sorting out and stacking of useful materials and disposing off the excavated stuff with in the site for all lead, all lift/ depth (excluding hard rock and black cotton soil) anywhere from the site etc complete as directed by Engineer in charge. - Any type of soil or rock not requiring Blasting.

Providing material and labour for Filling in foundation, plinth and plot filling with murrum (brought from out side) CBR value higher than 8% in layers of 20cm. thickness including watering, ramming and consolidating etc complete as directed by Engineer in charge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each deposited layer by ramming and watering. (Ramping by manual or mechanical means)

Disposing off the un-used excavated earth (black cotton soil) for all lead and lift/ depth out side the site at non objectional place as directed by Engineer in charge.

Rolling of earthwork in layers with power roller including filling in depressions which occur during the process including watering of earthworks.

Providing material and labour for Filling in plinth with coarse sand with CBR value higher than 8% under floors or base of foundation including watering ramming, consolidating and dressing etc complete as directed by Engineer in charge.

Providing and filling in rubbles in foundation, in plinth and for plinth protection, filling, with quarry spalls covering and leveling the surface in layers of 20 cm thickness stone/metals or stone chips, including watering, ramming well and consolidating each layer using minimum 100mm cut size stones. (Ramping by manual or mechanical means)

Carrying out plinth treatment to post construction / existing structure by spraying chemical solution for termite control treatment including labour and material consistment with I.S.I specification. Using Chlordene and Chiorpurfiles 20 EC. As Per 6131_paret-II Concentration Weight one percent is recommended i.e one litre 20 EC chemical emulsion with 19 liter give 1 % concentration inclusive of one litre chemical emulsion application at the rate of 5 Litre chemical / Sqm of surface is recommended as per I.S

Dewatering in all sorts of soil and soft murrum, hard Murrum and boulders, Soft Rock, Hard Rock including removal of surface water, water from foundation, trenches and ground water as nessesary to performed construction required by the contract in accodance with the specification.

Construction of Granular sub-base (GSB) by providing close graded Material conforming to specifications, mixing in place method with rotavator at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing, laying, spreading and compacting graded stone aggregate to Wet mix macadam (WMM) specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

Providing and laying Dense Graded Bituminous Macadam (DBM) using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specificatons and directions of Engineer-in-Charge. (50 to 100 mm average compacted thickness with bitumen of grade VG-40 @ 4.5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.)

Providing and laying Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge. 30 mm compacted thickness with bitumen of grade VG-40 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.

Providing and applying tack coat with bitumen emulsion (RS-1) using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom.

Providing and applying Prime coat with bitumen emulsion (SS1) Bulk using emulsion pressure distributor on prepared surface of granular base including clearing of road surface and spraying emulsion at the rate of 0.60 kg/sqm using emulsion pressure distributor for finished item of work etc.

Painting the BT surface with bitumen of grade VG-40 including cleaning the surface using wire brushes and air compressor and then applying the bitumen @7.00 kg/10 sqmt with mechanical sprayer and flushing fine clean sand @0.03 cum/10 sqmt over the asphalt painted surface including the cost of material, transportation, royalty chargers, heating of bitumen, hire charges of air compressor, sprayer and all type of labours & materials etc. complete as directed by Engineer in charges etc. complete

Providing and fixing pre-cast fair finish concrete kerb stone with vacuum wet hydraulic pressing technology of M30 grade cement based concrete block 60x30cm LXH and 15/12.5cm thick as per approved design and including excavation for fixing in proper line and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc complete including corner, quadrants, angles, radius, dropper kerbs in all shapes (Brands: Vyara, Alcock)

Regulatory / Mandatory Sign :-Providing and fixing sign boards made out of 2mm aluminium sheet / 4mm ACP (Aluminum composite Panel); size 60 cms. Dia Circle as per design of IRC- 67-2012. Pre treated with phospheting process & acid etching; coated with one coat of epoxy primer and two coats of best quality epoxy paint ; reflectorised with High Intensity Prismatic Grade retro refiectivesheeting of Type-4 as per ASTM D-4956 and latest M.O.S.T.Specifications; 3.6mtr long stand post of Iron Angle 75 x 75 x 6mm / 65NB Circular MS Pipe as required and frame fabricated from suitable size iron angle of 35 x 35 x 3mm; painted with bestquality epoxy coatings in black and white bends. The details of symbol for each board shall be as per the instruction of engineer in charge. The fixing at site shall be in 1:2:4 CC blockof size 45 x 45 x 60 Cms. for each leg including excavation, curing etc.complete under the supervision of engineer in charge. A warranty for 7 years for the Retro reflective sheeting from original manufacturer & a certified copy of 3 year outdoor exposure test report from third party test lab for the product offered shall be submitted by contractor. (B) Class-B Type-4 Retro Reflective sheeting.

Parking Sign :-Providing and fixing sign boards made out of 2mm aluminium sheet / 4mm ACP (Aluminum composite Panel); size size 60 x 60cms. sequare plus 60 x 20cms rectangular additional plate as as per the design of IRC-67- 2012. Pre treated with phospheting process & acid etching; coated with one coat of epoxy primer and two coats of best quality epoxy paint ; reflectorised with High Intensity Prismatic Grade retro refiectivesheeting of Type-4 as per ASTM D-4956 and latest M.O.S.T.Specifications; 3.6mtr long stand post of Iron Angle 75 x 75 x 6mm / 65NB Circular MS Pipe as required and frame fabricated from suitable size iron angle of 35 x 35 x 3mm; painted with bestquality epoxy coatings in black and white bends. The details of symbol for each board shall be as per the instruction of engineer in charge. The fixing at site shall be in 1:2:4 CC blockof size 45 x 45 x 60 Cms. for each leg including excavation, curing etc.complete under the supervision of engineer in charge. A warranty for 7 years for the Retro reflective sheeting from original manufacturer & a certified copy of 3 year outdoor exposure test report from third party test lab for the product offered shall be submitted by contractor. (B) Class-B Type-4 Retro Reflective sheeting.

Sign board per Square Meter :-Providing and fixing sign boards made out of 2mm aluminium sheet / 4mm ACP (Aluminum composite Panel); size 1 meter x 1meter as per design of IRC- 67-2012. Pre treated with phospheting process & acid etching; coated with one coat of epoxy primer and two coats of best quality epoxy paint ; reflectorised with High Intensity Prismatic Grade retro refiectivesheeting of Type-4 as per ASTM D-4956 and latest M.O.S.T.Specifications; 4 mtr long stand post (2 Nos.) of Iron Angle 75 x 75 x 6mm / 65NB Circular MS Pipe as required and frame fabricated from suitable size iron angle of 50x50x5mm; painted with bestquality epoxy coatings in black and white bends. the details of symbol or inscription / numerals for each board shall be as per the instruction of engineer in charge. The fixing at site shall be in 1:2:4 CC blockof size 45 x 45 x 60 Cms. for each leg including excavation, curing etc.complete under the supervision of engineer in charge. A warranty for 7 years for the Retro reflective sheeting from original manufacturer & a certified copy of 3 year outdoor exposure test report from third party test lab for the product offered shall be submitted by contractor. (B) Class-B Type-4 Retro Reflective sheeting

Road marking with hot applied thermoplastic paints with reflectorising glass beads on bitumin surface providing and laying a hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250gms per sqm area, thickness of 2.5mm is excluding of surface applied glass beds as per IRC:35-2015. The finished surface to be level, uniform and free from streaks and holes. zebra patta /bump patta lane/center line/ edge line/cut patta. The white color marking should provide liminance coefficinet on cemend road shalll be min 130 mcd/m2/lux and Asphalt road shall be min 100 mcd/m2/lux during the service life during the day time. The marking should meet the performance criteria for night time reflectivity, wet reflectivity and skid resistance as mentioned in the section-15 of IRC 35-2015. Warranty for the Retro reflectivity should be two years.

Supplying and fixing cat eye (Stimsonite) made out from Acrilo beautile sterine injuction high compressed molding with reflector made of MMC (prismatic type of size 12cm x 6cm x 2.5cm) provided with bituminous adhesive 100g. with each unit for fixing. (High Intensity grade)

Providing material and labour for laying Plain cement concrete 1:3:6 (1- Cement : 3- Coarse sand : 6- crushed stone aggregates 20 mm nominal size) in Foundation, Plinth, Pavement, Road work including cost of formwork, compacting, finishing, curing etc complete for all level, all height/ depth as directed by engineer in charge.

Providing Material and Labour for laying cement concrete1:2:4(1- Cement : 2- Coarse sand : 4- crushed stone aggregates 20 mm nominal size)and curing complete excluding cost of form work in (A) Foundation and Plinth

Providing material and labour for laying controlled cement concrete M25 produced in batch mix machine, using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregates conforming to latest IS 383 (without fly ash) for durability shall be followed as per approved design mix and latest IS 456 for reinforced concrete work in Foundation, footings, base of columns, pavement, grade slab, roads and Mass concrete including cost of Formwork with centering, steel/ply shuttering, strutting, steel scaffolding and propping etc. exluding cost of reinforcement. Height of propping and centering below supporting floor to ceiling not exceeding 4 M and removal of the same for in situ reinforced concrete and plain concrete work in with all lead and lift complete as directed by engineer in charge.

Providing and laying in position Ready Mixed M25 grade concrete for reinforced cement concrete work , using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying in Foundation, footings, base of columns, pavement, grade slab, roads and Mass concrete including cost of Formwork with centering, steel/ply shuttering, strutting, steel scaffolding and propping etc. exluding cost of reinforcement. Height of propping and centering below supporting floor to ceiling not exceeding 4 M and removal of the same for in situ reinforced concrete and plain concrete work in with all lead and lift complete as directed by engineer in charge.Including cost of admixtures in recommended proportions as per IS: 9103 and placing of PVC sleeves during casting as per direction of the EIC. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) Including providing and adding colour pigment as admixture of approved make.

Providing and laying in position Ready Mixed M25 grade concrete for reinforced cement concrete work , using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying in Columns, Fins, Pillars posts, Rectangular polygon in plan and struts upto floor two level including cost of Fair /Expose RCC finish Formwork with centering, steel/ply shuttering, strutting, steel scaffolding and propping etc. exluding cost of reinforcement. Height of propping and centering below supporting floor to ceiling not exceeding 4 M and removal of the same for in situ reinforced concrete and plain concrete work in with all lead and lift complete as directed by engineer in charge.Including cost of admixtures in recommended proportions as per IS: 9103 and placing of PVC sleeves during casting as per direction of the EIC. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) Including providing and adding colour pigment as admixture of approved make.

Providing and laying in position Ready Mixed M25 grade concrete for reinforced cement concrete work , using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying in Walls, from top of foundation level upto floor two level including cost of Fair /Expose RCC finish Formwork with centering, steel/ply shuttering, strutting, steel scaffolding and propping etc. exluding cost of reinforcement. Height of propping and centering below supporting floor to ceiling not exceeding 4 M and removal of the same for in situ reinforced concrete and plain concrete work in with all lead and lift complete as directed by engineer in charge.Including cost of admixtures in recommended proportions as per IS: 9103 and placing of PVC sleeves during casting as per direction of the EIC. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) Including providing and adding colour pigment as admixture of approved make.

Providing and laying in position Ready Mixed M25 grade concrete for reinforced cement concrete work , using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying in Slabs, landing, lintels, shelves, Balconies and Cantilever upto floor two level including cost of Fair /Expose RCC finish Formwork with centering, shuttering, strutting, steel scaffolding and propping etc. exluding cost of reinforcement. Height of propping and centering below supporting floor to ceiling not exceeding 4 M and removal of the same for in situ reinforced concrete and plain concrete work in with all lead and lift complete as directed by engineer in charge.Including cost of admixtures in recommended proportions as per IS: 9103 and placing of PVC sleeves during casting as per direction of the EIC. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) Including providing and adding colour pigment as admixture of approved make.

Providing and laying in position Ready Mixed M25 grade concrete for reinforced cement concrete work , using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying in Beams, Plinth beam, Girders, Lintels and Cantilever upto floor two level including cost of Fair /Expose RCC finish Formwork with centering, steel shuttering, strutting and propping etc. exluding cost of reinforcement. Height of propping and centering below supporting floor to ceiling not exceeding 4 M and removal of the same for in situ reinforced concrete and plain concrete work in with all lead and lift complete as directed by engineer in charge.Including cost of admixtures in recommended proportions as per IS: 9103 and placing of PVC sleeves during casting as per direction of the EIC. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) Including providing and adding colour pigment as admixture of approved make.

Providing and laying in position Ready Mixed M25 grade concrete for reinforced cement concrete work , using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying in Stair and landing upto floor two level including cost of Fair /Expose RCC finish Formwork with centering, steel/ply shuttering, strutting, steel scaffolding and propping etc. exluding cost of reinforcement. Height of propping and centering below supporting floor to ceiling not exceeding 4 M and removal of the same for in situ reinforced concrete and plain concrete work in with all lead and lift complete as directed by engineer in charge.Including cost of admixtures in recommended proportions as per IS: 9103 and placing of PVC sleeves during casting as per direction of the EIC. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) Including providing and adding colour pigment as admixture of approved make.

Providing and Core cutting work in Stone/RCC/Brick structures of maximum 400mm depth upto 150mm Dia with required core-cutting wet drilling, fastners tools, labour and supervision etc complete.

Providing & laying weep hole in Abutments, walls and returns by using A.C. pipe of 100mm including laying in proper grade and jointing the completed as per detailed specification.

Providing material and labour for fixing chemical anchor medium to heavy duty injection adhesive for Anchor fixing in Dry conditions and HILTI HIT-HY 200 + HIT-V rods of size 16mm x 300mm of HILTI or equivalent as per drawing or as instructed by EIC. The system should be made of two foils consisting of resin and Hardener foil pack. The system can be used for threaded rods HIT-V rods or equivalent rods. The installation and the setting instructions should be strictly followed as per the manufacturers recommendations. Rate shall be inclusive of injection adhesive and fastner rod of same make.

Providing material and labour for fixing in position PVC pipe sleeves 75-160mm Diameter - 6Kg/cm2 and length as per design for following diameters for services wherever pipes pass through walls/ slabs/ beam in mtrs length. All pipes shall be accurately cut to the required sizes, laid as per drawing, kept in the position while concreting, and burrs removed before laying etc complete for all floors, all height as directed by engineer in charge. Open ends of the pipe shall be closed as the pipe is installed to avoid clogging while concreting. Pipe sleeve shall be removed before water proofing or grouting (at rain water down take location).

Supplying and fixing reinforced concrete heavy duty non-pressure NP3 pipes with collars/without collars as per IS 458-1991 specifications including setting the pipes in ground for tree protection. 600 mm dia

Supplying, cutting, bending, binding and placing in position Corrosion Resistance Steel TMT bars in all diameter Fe 500/ 500D grade confirming to relevant I.S. standards as per ISS 2502 and IS 1786 including cost of steel and binding with GI wire in position complete upto floor two level (Brands: Tata, Electrotherm, Jindal)

Steel works: Providing material and labour for fabricating, assembling, hoisting/ erecting and fixing in position at all heights/ all levels/ all floors/ all shapes & sizes with all leads & lifts using MS Rolled Steel Sections, ISMB, ISMC, UC, H-Section, Hollow sections, Tubular Sections, MS Plates, Chequered Plates, MS Pipes, Perforated Sheet, Flats, Bars, Angles, MS Sheet, Girder, Beam, cattle trap, deep threaded MS bolts. All confirming to latest relevant IS codes for the work of steel structures like staircases, railings, handrail, jali, gates, grills, bracings, platforms, brackets, monkey ladder, cattle trap, rungs, Roof canopy, fencing posts, M.S. Screen etc. including straightening, cutting, bending, bolting and welding the members including necessary scaffolding/ staging etc. complete and comprising of Profile Cutting, Smooth grinding/ machining of edges/ faces/ all welding joints; Necessary welding; Machine drilling of holes for joining/ anchoring; dry sanding, degreasing (wet cleaning) & preparation of rustfree surface manually or mechanically, metal putty to make the surface even and smooth. The Contractor shall prepare shop drawing as per GFC drawing and as per actual site condition and get approved before execution by EIC. (Standard measurements will be paid for as actual cut length used at site) .(Brand: Tata Steel, Jindal)

Providing and fixing M.S. round holding down or anchor bolts with nuts and washer plates complete.

Providing material and labour for laying Brick work using common burnt clay building Conventional bricks having crushing strength not less than 35 kg/SqCm in foundation and plinth in Cement Mortar 1:5 (1- Cement : 5 -fine sand) in any shape and thickness including finishing, racking of joints, curing, scaffolding for all height all level etc. complete as directed by engineer-in-charge.

Providing material and labour for Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in superstructure above plinth level upto floor two level (B) Cement Mortar 1:5. (1- Cement : 5 -fine sand) in any shape and thickness including finishing, racking of joints, curing, scaffolding for all height all level etc. complete as directed by engineer-in-charge.

Providing material and labour for (i) Half brick masonry in common brunt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in foundation, plinth and superstructure above plinth level upto floor two level, in any shape and thickness including finishing, racking of joints, curing, scaffolding for all height all level etc. complete as directed by engineer-in-charge.(Conventional)

Providing and fixing frames/shutters/louvers for any type of aluminium works in door/window/partition made out of heavy weight extruded aluminium sections of approved make having minimum 50 micron pure polyester Powder Coated coating of approved shade, texture & colour for all floors, levels, heights, shapes, sizes including cutting, bending, crimping, fabricating in best workmanship manner etc excluding glass works as per the drawing and as directed by Architect or Engineer-in-Charge. Including 1) Sheet metal screws and casted solid aluminum corner cleats fixed with external byttins with a spring for rapid and secure joint assembly for casement and sliding shutter and frame; 2) Glazing clips for receiving infill panel; 3) Best quality wool pile and compatible EPDM rubber; 4) Dash Anchor fasteners of HILTI or equi. for fixing the frame at every 600 mm spacing. 5) 10mm GI tie rod for connecting vertical stile at top and bottom for aluminum door shutter and 4mm thick solid aluminium corner cleat of full thickness of section for connecting style and horizontal rails; 6) Providing and fixing packing (rough ground) in full periphery/ at every 600mm c/c with average 6 mm thick PVC spacer/ compact sheet of width ; 7) Filling the gap between wall and frame on both sides with polyethylene baker rod of avg. 10 mm thickness with silicon sealant . 8) Termite treated seasoned teak wood. 9)Zinc alloy powder coated touch lock with hook. 10) Zinc alloy body with single nylon roller (weight bearing capacity to be 40 Kg). Contractor shall prepare shop drawing based on concept drawing and get approved from the consultants before procurement of material including making of mock up for approval with all hardwares. Rate shall be inclusive of all material, labour, fixing, accessories except glass works.

Providing material and labour for fixing 8mm thick Clear Toughen Glass as per approved sample of any size, any shape and specified thickness in frame and shutter work with necessary cutting of glass as per drawing & specifications including providing and fixing EPDM quality rubber/ silicon sealant/ structural sealant and 3M tape on the periphery of the glass as per the required thickness etc. complete at all floors/ all levels/ all heights as per the directions of Engineer in charge. Actual installed quantity shall be measured and paid.

Providing and fixing 5mm thk float glass pane frosted/plain glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): Actual installed quantity shall be measured and paid. Rate shall be inclusive of all type of wastage.

Providing and fixing 35 mm thick flush door filled with country wood with Indian Teak wood frame of 120x80 mm, water proof flush door single shutters with 1 mm thick lamination sheet on both sided (Make:Greenlam/Royale Touche/ Euro/ all sides of shutters) with lipping edging patti all around the door including using 2 Nos pull SS handles in satin finish of the size 25mm diameter, 30 cm long made from anticorrosive high grade AISI 316 stainless steel. Providing and fixing one number of 10 mm diameter 20 cm long anticorrosive high grade AISI 316 stainless steel tower bolt, four numbers of anticorrosive high grade AISI 304 stainless steel hinges of size 102 mm x 76 mm x 3 mm of the make KICH & anticorrosive high grade AISI 316 stainless steel aldrop of 10 mm diameter x 20 cm ( make ORBIT, Kich) in satin finish, with fixing SS heavy duty screws to the frame as approved by Engineer -in-charge etc. complete as per detailed drawing. ALL FLOORS

Providing and fixing 25 mm thick flush door filled with country wood, water proof flush door single shutters with 1 mm thick lamination sheet on both sided (Make:Greenlam/Royale Touche/ Euro/ all sides of shutters) with lipping edging patti all around the door including using 2 Nos pull SS handles in satin finish of the size 25mm diameter, 15 cm long made from anticorrosive high grade AISI 316 stainless steel. Providing and fixing one number of 10 mm diameter 20 cm long anticorrosive high grade AISI 316 stainless steel tower bolt, four numbers of anticorrosive high grade AISI 304 stainless steel hinges of size 102 mm x 76 mm x 3 mm of the make KICH & anticorrosive high grade AISI 316 stainless steel aldrop of 10 mm diameter x 20 cm ( make ORBIT, Kich) in satin finish, with fixing SS heavy duty screws to the frame as approved by Engineer -in-charge etc. complete as per detailed drawing. ALL FLOORS

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). No Weilding OR Fabrication shall be allowed at site. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). Sample shall be approved before execution. Contractor shall arrange mock up of railing system (2 or 3 no) in required length as directed by Architect. Contractor shall protect railing system uptill handling over the project.

Providing & fixing Locks Godrej Mortice lock cover (with 3 sets of key) with all required tools and tackles, gaskets, screws in line and level at the height mentioned in the drawing, cutting and core the doors in exact dimensions, without damaging the shutter or frames up to the satisfaction of engineer in charge with Standard warranty of 1 year

Providing & fixing S.S. Pipe Handle of 30 Cm size of ASIS 316 Grade with all required tools and tackles, gaskets, screws in line and level at the height mentioned in the drawing up to the satisfaction of engineer in charge. (Brands KICH, OZONE AND ENOX)

Providing & fixing S.S. Pipe Handle of 10 Cm size of SS 304 Grade with all required tools and tackles, gaskets, screws in line and level at the height mentioned in the drawing up to the satisfaction of engineer in charge. (Brands KICH, OZONE AND ENOX)

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. (Brand Ozone, Kich, Enox)

Providing and fixing IS:12817 marked stainless steel butt hinges of 4x1x1" inches with stainless steel screws etc. complete in doors, windows, louvers as per drawings.

Providing & fixing Louvers of Anodized aluminium sections as horizontal members at 75 mm c/c and 100 x 25 x 2 mm (Wt. 1.16 kg/m) aluminium vertical section 125x25X2 mm (Wt. 1.43 kg/m) with SS 304 Aldrop 20 cm long including fixing and erection on site and making surface good etc. complete as per design for doors/windows/ventilators.

Providing and fixing in position, interlocking rolling shutter of approved make, made of 18 gauge, 75mm wide cold rolled GI lath interlocked, including top cover (20 gauge), spring, axles (specially designed shaft), guide rails (10 gauge), tees, iron pulleys, ball bearings, handles, arrangement for inside and outside locking arrangement, with Mechanical Type (Gear Arrangement), holding down bolts embedded in CC 1:2:4 / anchor fastener of HILTI or equivalent including 1 coat of Rustocap and 2 coat of Hi-Gloss Metal PU Paint of approved make and shade over all the surfaces etc. as directed. (Measurements considered for payments shall be clear size of opening plus guide channels on both the sides for width and 450mm on top for drum height.)

Providing, making and fixing wall mounted 150mm high, 450 lenght and 1mm thick SS 304 for signage painted with paint in Gujarati, Hindi and English languages and the font style as approved sample or as per design and drawings. It shall be made from ISI Brushed S.S. 304. It shall be fixed on the wall with chemical anchor fastener at any level any height. All Edges and corners shall be smoothened. Width of the letter shall as per the proportion of the word for depth. The rate shall be inclusive of scaffolding, drilling, adhesive material, screwing, stud fitting etc. complete for all heights.

Providing throating or plaster drip groove 10 x 10 MM and moulding to RCC chajja and horizontal surfaces.

Providing and carrying out Washed stone /peeble grit plaster on exterior walls height upto 16 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1cement : 4 coarse sand ), furrowing the under layer with scratching tool,applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone/pebble chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings in all colour, proportions and mix of Grit/stone chips, complete as per specification and direction of Engineer.

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the top layer of washed stone/pebble grit plastered surface as per approved pattern, including providing and fixing aluminium channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove iincluding removal of channel if required, complete as per specifications and direction of the Engineer-in-Charge.

Providing material and labour for fixing G.I. hexagonal chickenmesh of size 16mm x 24mm of 22 gauge at junction of concrete and brick work or between different materials after making "V" grove between two different material surface and filled with rich cement mortar and @ 100mm on each side of surfaces including necessary "U" nails/ screws/ washers with cleats for fixing, overlaps, curing, scaffolding etc complete for all floors/ all levels/ all heights/ all shapes as per direction of Engineer-in-charge.

Providing and applying 10mm thick cement plaster in single coat plastering on ceilings and sofits of stairs upto all levels/floors (i)Cement mortar 1:3 (1-cement:3-sand) including finishing with a floating coat of neat cement slurry, scaffolding, curing, finishing, making grooves, forming pattas etc. complete as directed by the Engineer-in-charge.

Providing and applying 15mm thick cement plaster in single coat on Rough (Similar)side of single or half brick/ AAC blocks walls for plastering upto all levels/floors and finished even and smooth in (i) Cement mortar 1:3 (1-cement:3-sand). Including scaffolding, curing, finishing, making grooves, forming pattas etc. complete as directed by the Engineer-in-charge.

Providing and appying 20mm thick sand faced cement plaster on walls upto height 10 metres above ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. complete. Including scaffolding, curing, finishing, making grooves, forming pattas etc. complete as directed by the Engineer-in-charge.

Providing and applying Wall painting (two coats) with plastic emulsion paint of approved brand having VOC (Volatile Organic Compound) content and manufacture on undecorated wall surface to give an even shade including required scaffolding, thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth.( make Asian, Berger, Dulex, Nerolac)

Providing and applying two coats of Birla (white cement based) or Asian (acrylic lapy- putty) or equivalent & two coats of primer of approved brand and manufacture on new wall surface to give an even shade including required scaffolding, thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth.

Providing material and labour for Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an required shape even shade after thoroughly brushing the surface to remove all dirt, and remains of loose powdered materials.etc complete inluding required scaffolding. (make: Asian, Berger, Dulex, Nerolac)

Providing material and labour for applying Epoxy based Paint for Metal works on new/ existing metal surface af including including cleaning and removal of all dirt, grease, varnish, paint or any other foreign matter. Hereafter surface sanding before and after the paint to provide seamless aesthetic look complete as per the instructions with proper tools and sanding and wire brushing. First application of 2 coats of mixed red oxide zinc chromate primer of approved brand paint to be applied and there after application of putty works and sanding work, thereafter application of 2 coats of epoxy base paint finish. Sample to be approved before starting of the work by Architect/ EIC. Rate shall be inclusive of the cost of scafolding. (Brands: Asian paint Apcolite Epoxy, Berger, Dulex, Nerolac)

Providing and applying Hot dip Galvanised coating confirming to Indian Standard 4579/2629/2633 with zinc coating thickness to be 86 micron and before application of GI coating the material should be free from all dirt, grease, varnish, paint or any other foreign matter. Including touching of local exposed areas with Zinc metal spray paint with 2 coats to make the structure corrosion free with cleaning thoroughly the applied surface making it free from grease, paint or any other foreign matter , sanding the surface before and after the paint to provide seamless aestheic look complete as per the instructions of the EIC including transport/loading/unloading the materials at plant for HDGC work

Providing and Laying broken China mosaic flooring for terrace using 12 to 20 mm broken pieces of only white glazed tiles (Bell/ Somany/ Johnson/ kajaria/ Cera/ Spartek/Orient / Nitco) to be laid over cement mortar 1:3 to plain or slope and to be tempered to bring mortar cream out up to surface using white cement including off junctions and extending them up to wall top, curing with water and cleaning with oxalic acid etc as directed.

Providing and laying integral cement based water proofing treatment conforming to IS: 2645 for treatment of roofs, balconies, terraces etc: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brickbats 25 mm to 115 mm size with 50% of cement mortar 1:5 admixed with water proofing compound over 20 mm thick layer of cement mortar of mix 1:5 admixed with water proofing compound to required slope and treating similarly the adjoining walls upto 300 mm height rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed jointless cement mortar of mix 1:4 admixed with water proofing compound conforming to IS : 2645 and approved by EIC.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by EIC including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) Curing terrace with water flooded for min. 2 weeks. All above operations to be done in order and as directed and specified by the EIC with average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing cement vata (10 cm X 10 cm size) quarter round in Cement Mortar 1:1 including neat cement finishing, watering etc complete

Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles having Tegular edge & 15 mm Thick Densified edges on the Tile Periphery for Extra Strength The Light weight calcium silicate ceiling tiles shall have , light reflection 85% non-combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity0.043° w/m KC.for the best thermal Insulation . The Light weight calcium Silicate tile shall be of approved texture of size 595 X 595 mm to be laid on true horizontal level suspended inter locking metal grid of hot dipped galvanized steel sections consisting of main ‘T’ runner suitably spaced at joints to get required length and size of 24X38mm made from 0.30 mm thick (minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size 24X28mm made out of 0.33mm (Minimum) sheet spaced 1200mm along spaced between main ‘T’ at 600mm centre to centre to form agrid of 1200X600mm and secondary cross ’T’ of length 600mm and size 24x28mm made of 0.30 mm thick (Minimum) sheet to be interlocked at middle of the 1200X600mm panel to form grid of size 600X600mm resting on periphery walls/partitions on a perimeter wall angle pre-coated steel of size (24X24X3000mm made of 0.40mm thick (min) sheet with the help of rawl plugs at 450mm centre to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick Densified edges light weight calcium silicate ceiling tiles of approved texture (Fine Fissured/ Cosmos/ Spintone) in the grid including, cutting /making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required, Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25X35 X1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm G.I. adjustable rods with galvanized steel level clips of size 85X30X0.8mm, spaced at 1200mm centre to centre long main ‘T’ bottom exposed with 24mm of all T-sections shall be pre-painted with polyester baked paint, for all heights, as per specifications, drawings and as directed by engineer-in-charge.

Providing and laying cement mortar in 1:6 (1-Cement : 6-coarse sand) proportion.

Providing Materiall and Labour For laying polished kota stone slab 25mm thick in risers of steps,skirting Dado and pillars laid on 10mm thick cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with gray cement slury mixed with pigment to match the shade of slab including rubbing and polishing etc. complete. Sample shall be approved before execution. Kota stone shall be in uniform shade of required size. Sample and mockup shall be approved before procurement of material.

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of cement mortar 1:6 (1- cement: 6-coarse sand) or L.M. 1.1.51aid over and jointed with grey cement slurry including rubbing and polishing etc. complete. (B) 30 mm thick

Providing and laying Polished/Natural finish Rajula stone of 22-25 mm thk stone slab/ flooring/wall mounted with edge cutting in required sizes, design and patterns, in linear as well as curvilinear portions all complete as per the architectural drawings over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with cement slurry admixed with pigment of matching shade including wastage,rubbing, cutting, curing and polishing etc all complete as specified and as directed by the Engineering- Charge

Providing and laying POLISHED Granite stone 25mm thk flooring/wall in required design and patterns, in linear as well as curvilinear portions all complete as per the architectural drawings with 25 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with cement slurry admixed with pigment of matching shade including wastage,rubbing, cutting, curing and polishing etc all complete as specified and as directed by the Engineer-in-Charge : Colour Jet Black, Cherry Red, Steel grey, Elite Brown, Cat Eye or equivalent.

Providing and fixing 20 mm thick Granite gang saw cut, mirror polished, premoulded and prepolished, machine cut for wall cladding,plaforms, vanity counters, window sills , facades, in linear as well as curvilinear surfaces and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:2 (1 cement : 2 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Including fixing granite stone, over and above corresponding basic item, in facia, wall cladding and drops with chemical adhesive, including cleaning etc. complete. For all wall Caldding and Copping work also as per drawing including all colour and texture. (Brand for Adhesive:MYK Laticrete, Weber,Kerakoll)

Providing Edge moulding upto 25 mm thick Granite/Kota/ other stones counters, Vanities, steps/ riser etc., including machine polishing to edge to give high gloss finish etc.including wastage,rubbing, cutting, curing and polishing etc complete as per design approved by Engineer-in-Charge.

Providing and laying double charged Antiskid vitrified tiles in floor (thickness to be specified by manufacturer) with residue of approved make and shade as per drawing with water absorption less than 0.08% and confirming to IS: 15622, laid over 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand) bedding of approved make, in all colours and shades. Finishing shall be done with pointing the joints with grey cement slurry at 3.3kg/sq m including grouting the joints with white cement and matching pigment, including curing, cleaning with mild oxalic acid, maintaining till handling over by covering with plastic sheet etc complete for all floor all height as directed by Engineer-in-charge. (Brands: Johnson, Kajaria, Asian, RAK, NITCO)

Extra for providing material and labour for Grouting the joints of any type of flooring tiles of Size upto 600mm having joints of 3mm width and in full depth, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade and approved make (0.10 kg of hardener and 0.20 kg of resin per kg), including filling/ grouting and finishing complete as per direction of Engineer-in-charge.

Providing and laying coloured glazed tiles 8-10 mm thick of the size 300x 300 mm / 300x 450 mm / 300x600mm in skirting, risers of steps and dado on 10 mm. thick cement plaster 1:3 (1 cement : 3 coarse sand) & jointed with white cement slurry. (make Johnson, Kajaria, Asian, RAK, NITCO).

Providing and fixing pre-cast Rubber Dye inter locking concrete block 80 mm thick with grade of concrete M40 pumatic compressed by mechanically pressed and as per approved desing including 35 mm sand layer for levelling and filling the joint with sand in proper line and level.

Providing and fixing 80-100 mm thick Granite Cobble stone (Size: 10x10, 14x14, 10x20 cm) Colour: Cherry Red, Elite Brown, yellow, white or equivalent. block hand cut with machine cut 25 mm deep top edges all side, rounded edges and chisel dressed on top, for paving in floors, drains etc. laid over 30mm minimum thick base of cement mortar 1:4 (1 cement: 4 coarse sand floated with thick and neat cement paste mixed with approved pigment to match the shade of the stone. including dressing, rubbing, curing, rounded edges, wedge, tappering, cleaning etc. Complete with no more than 5mm floor top level variation (the rate shall be for different patterns and details provided by the Architect. No extra amount will be paid for residues to be used to achieve the pattern).

Providing and laying Tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and fixing of 25 mm thick EPDM flooring for Childrens play area in multi colour with 6mm thick EPDM granule top layer, 19 mm thick SBR rubber layer, applied with fast curing polyurathine binder including wastage and complete as per EIC (Brands Ecoflex, Koochieplay, Ebaco)

Seating (Module 8) : Providing and fixing GFRC Cast Concrete Stool of 450x450 mm (DiaxH) and 38mm thickness as per drawing. Each unit will have smooth finish, including transportation, cost of loading, unloading and placing in place with required base. (Brands: Encoar Studio,The Concrete shop)

Table (Module 9) : Providing and fixing GFRC cast concrete Table of size 600x800x745mm (LBH) fixed on a 4mm thick and 200mm dia base plate with a 30mm thick polished kotastone top supported on 25mm thick metal box framing as per the drawing. All MS items to be Hot dip Galvanised coating confirming to Indian Standard 4579/2629/2633 with zinc coating thickness to be 86 micron.

Table (Module 10) : Providing and fixing GFRC cast concrete Table of size 900x900x745mm (LBH) fixed on a 6mm thick and 300mm dia base plate with a 30mm thick polished kotastone top supported on 25mm thick metal box framing as per the drawing. All MS items to be Hot dip Galvanised coating confirming to Indian Standard 4579/2629/2633 with zinc coating thickness to be 86 micron.

Table (Module 11) : Providing and fixing GFRC cast concrete Table of size 900x900x745mm (LBH) fixed on a 6mm thick and 300mm dia base plate with a 30mm thick polished kotastone top supported on 25mm thick metal box framing as per the drawing. All MS items to be Hot dip Galvanised coating confirming to Indian Standard 4579/2629/2633 with zinc coating thickness to be 86 micron.

Table (Module 12) : Providing and fixing GFRC cast concrete Table of size 700x1100x745mm (LBH) fixed on a 4mm thick and 200mm dia base plate with a 30mm thick polished kotastone top supported on 25mm thick metal box framing as per the drawing. All MS items to be Hot dip Galvanised coating confirming to Indian Standard 4579/2629/2633 with zinc coating thickness to be 86 micron.

Cycle stand: Providing and Fixing Bicycle stand made from (Stainless Steel 316) of 875x790mm length, 50 mm pipe dia and wall thickness of 1.5 mm with Glossy/ Matt finish, high quality grade including bending, by CNC hydro-pneumatic bends and fabrication including transportation, loading, unloading, cutting, facing, wielding, finishing, buffing , finishing in any shape and curvature with excavation and fixing in position, line and level complete as per EIC- High quality grade. (Brand: Cheveron Inc)

Design signage 01: Providing and fixing MS Signage board of size 1500x900mm rectangle as per the design drawing, coated with one coat of epoxy primer and two coats of best quality epoxy paint; reflectorized with retro reflective sheeting as per latest M.O.S.T. Specifications; stand post and frame fabricated from suitable size hot dip galvanised iron angle, post as required; painted with best quality epoxy coatings. the details of symbol or inscription / numerals for each board shall be as per the instruction of engineer in charge. The fixing at site shall be in 1:2:4 CC block of size 45 x 45 x 60cms. for each leg. including excavation curing, loading, unloading, transportation, paint complete. complete under the supervision of engineer in charge.

Design signage 02: Providing and fixing MS Signage board of size 2150x3600mm rectangle as per the design drawing, coated with one coat of epoxy primer and two coats of best quality epoxy paint; reflectorized with retro reflective sheeting as per latest M.O.S.T. Specifications; stand post and frame fabricated from suitable size hot dip galvanised iron angle, post as required; painted with best quality epoxy coatings. the details of symbol or inscription / numerals for each board shall be as per the instruction of engineer in charge. The fixing at site shall be in 1:2:4 CC block of size 45 x 45 x 60cms. for each leg. including excavation curing, loading, unloading, transportation, paint complete. complete under the supervision of engineer in charge.

Feature Wall steel works: Providing and fixing MS Feature wall of size 12225x3500mm and 4mm thick MS sheet as per the drawing including loading, unloading, transportation, paint complete. All MS items to be Hot dip Galvanised coating confirming to Indian Standard 4579/2629/2633 with zinc coating thickness to be 86 micron.

Trenching in ordinary soil up to a depth of 90 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying stacking and spreading of good earth at site including royalty and carriage upto 5 k m lead complete (earth measured in stacks will be reduced by 20% for payment).

Carting of soil from inside plant area, including to loading , unloading and transport

Supplying , stacking and spreading sludge / well decayed farm yard manure from thesource approved by the engineer in charge incl. screening, loading, unloading, conveyance and stacking at site.

Mixing earth and manure or in proportion specified or directed, Spreading of dung manure or / and good earth in required thickness. and fine dressing the ground as per natural gradiant

Providing & Laying CE certified (minimum life of 25 years) thermally fused virgin polypropylene Geotextile thickness of less 0.6 mm and dimpled height of minimum 9 mm compulsorily having a self adhesive strip for overlap of the rolls. Roll Size: 12.5/15M x 2/2.4M.

Providing and planting saplings of plants/ trees (The height of plant shall be considered as 8'-10’ and girth size 60mm-80mm) in the proper beds as prepared , and maintaining the same for Two months by involving all the operations like multing, de-weeding , hoeing , forking, watering and application of chemical fertilizer, insecticides/pesticides etc. for the following trees/ plants (the pit shall be filled with fresh soil and manure, i.e as stacked at site,Digging holes in ordinary soil and carting away the excavated earth and refilling the holes with the fresh soil mixed with manure or in the ratio of 2 : 1 by volume the excavated earth shall be placed within premises at required place, rolling, levelling, watering and compaction etc. in required gradient complete as directed.Holes 1.2 m dia and 1.2 m deep. As per below items: 1. Pongamia pinnata

Bauhinia variegata

Lagerstoemia flos reginae

Samanea saman

Erythrina variegata

Gliricidia sepium

Cassia fistula

Tamarindus indica

Tabebuia rosea

Cassia javanica

Alstonia scholaris

Markhamia lutea

Terminalia catappa

Tabebuia argentea

Millettia peguensis

Senna siamea

Manilkara zapota

Cordia sebestenia

Acacia auriculiformia

Plumeria obtusa

Cerbera odollam

Fortunella japonica

Hibiscus tiliaceus

Providing and planting the hedges/shrubs ( 2'-3' height and girth size 8mm-12mm), border plants as mentioned below including making pits/trenches suitably to implant shrubs, including filling the fresh earth and manure and maintaining the same for Two months involving all the operations like multching , de- weeding ,hoeing, forking , application of chemical fertilizer ,insecticides / pesticides and trimming in proper shape.Digging holes in ordinary soil and carting away the excavated earth and refilling the holes with the fresh soil mixed with manure or in the ratio of 2 : 1 by volume the excavated earth shall be placed within premises at required place, rolling, levelling, watering and compaction etc. in required gradient complete as directed.Holes 0.45 m dia and 0.45 m deep. As per below items: 1. Pandamus Baptisti "variegated"

Cymbopogon Cytratus

Ficus Nitida

Hamelia Patens

Ixora Singaporensis

Pennisetum Setaceum

Pennisetum Setaceum "cuprus"

Hibiscus variegated

Cocoloba Unifera

Adhotoda Vasica

Jatropha Integrina

Stachyterpheta Jamaicensis

Cestrun Dinernum

Bauhinia Tomentosa

Pedilanthus Tithymaloides

Providing and planting saplings ( min. 6" height and girth size 5mm-8mm) of ground covers in the proper beds as prepared , and maintaining the same for Two months by involving all the operations like multing, de-weeding , hoeing , forking, watering and application of chemical fertilizer , insecticides / pesticides etc. for the following trees/ plants (the pit shall be filled with fresh soil and manure, i.e as stacked at site,Digging holes in ordinary soil and carting away the excavated earth and refilling the holes with the fresh soil mixed with manure or in the ratio of 2 : 1 by volume . the excavated earth shall be placed within premises at required place, rolling, levelling, watering and compaction etc. in required gradient complete as directed.Holes .15 m dia and .15 m deep.As per below items: 16 Wadelia Trilobata

Senecio Confusus

Caryssa Macrophylla "nano"

Asystacia Gangetica

Portulaca Grandiflora

Alternauthera Bettaikiana

Cuphea Hyssopifolia

Staking of trees done by tying of 2" dia. bamboo stakes with canvas webbing or rubber tubes. Minimum 3 stakes per tree.

STORM WATER Providing & Fixing of factory made precast U shape surface storm water drain having size of 450 mm x 450 mm X 2000 mm long, T-25 load carrying capacity-10 T Axle Load - 5 T Wheel Load confirming to JIS having high performance self-compacting concrete of M40 Cylinder Strength/ M50 Cube Strength & Fe 500 / Fe500D shall be use for reinforcement. The product shall have tie shape joint 10-20 mm width X 25 mm depth groove as per JIS on both sides of each Storm water drain for jointing two precast drains using cement mortar or suitable non shrink grout. The precast Storm water drain must consist of special in built inlets at appropriate location for fixing De-shackle for mechanical installation , including supply ,transportation ,installation on specific location at site in line ,level , gradient and plumb with necessary testing commissioning etc complete as per instruction of engineer in charge.In no case the casting shall be allowed to be prepared at site. It should be casted in the stringent atmospheric & pre-defined condition, including making cut-outs, core cutting for utility ducts as per approved QAP as by Engineer In charge. (Make: Fuji or equivalent)

Providing & laying factory made Precast Lid having length of 500 mm, width suitable for placing on U - Shape Drain (DUSD) 450 x 450 & thickness of 130 mm respectively. Lid should have T-25 load carrying capacity – 10 T Axle Load – 5 T Wheel Load, confirming to JIS & meeting IS requirements having High Performance Self Compacting Concrete of M-40 cylinder strength/ M-50 cube strength. The Fe 500/ Fe500D shall be used for reinforcement. Lid should have anti-skid finish at top. The each lid unit should have slits of 155 mm X 20 mm slit on two sides along the width of the lid for storm water intake. In no case the casting shall be allowed to be prepared at site. It should be casted in the stringent atmospheric & pre-defined condition, as per approved QAP as by Engineer In charge. (Make: Fuji or equivalent)

Providing & laying factory made Precast Perforated Lid having length of 500 mm, width 572 mm suitable for placing on U - Shape Drain (DUSD) sizes 450 mm x 450 mm (in to in) thickness of 130 mm respectively. Lid should have T-25 load carrying capacity – 10 T Axle Load – 5 T Wheel Load, confirming to JIS & meeting IS requirements having High Performance Self Compacting Concrete of M-40 cylinder strength/ M-50 cube strength. The Fe 500/ Fe500D shall be used for reinforcement. The Perforated lid unit should have 10 slits each of 135 mm X 20 mm slit for storm water intake. In no case the casting shall be allowed to be prepared at site. It should be casted in the stringent atmospheric & pre-defined condition, as per approved QAP as by Engineer In charge. (Make: Fuji or equivalent)

Providing & Fixing of factory made precast U shape surface storm water drain having size of 600 mm x 600 mm X 2000 mm long, T-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load confirming to JIS having high performance self-compacting concrete of M40 Cylinder Strength/ M50 Cube Strength & Fe 500 / Fe500D shall be use for reinforcement. The product shall have tie shape joint 10-20 mm width X 25 mm depth groove as per JIS on both sides of each Storm water drain for jointing two precast drains using cement mortar or suitable non shrink grout. The precast Storm water drain must consist of special in built inlets at appropriate location for fixing De-shackle for mechanical installation , including supply ,transportation ,installation on specific location at site in line ,level , gradient and plumb with necessary testing commissioning etc complete as per instruction of engineer in charge.In no case the casting shall be allowed to be prepared at site. It should be casted in the stringent atmospheric & pre-defined condition, including making cut-outs, core cutting for utility ducts as per approved QAP as by Engineer In charge. (Make: Fuji or equivalent)

Providing & laying factory made Precast Lid having length of 500 mm, width suitable for placing on U - Shape Drain (DUSD) 600 x 600 & thickness of 145 mm respectively. Lid should have T-25 load carrying capacity – 10 T Axle Load – 5 T Wheel Load, confirming to JIS & meeting IS requirements having High Performance Self Compacting Concrete of M-40 cylinder strength/ M-50 cube strength. The Fe 500/ Fe500D shall be used for reinforcement. Lid should have anti-skid finish at top. The each lid unit should have slits of 155 mm X 20 mm slit on two sides along the width of the lid for storm water intake. In no case the casting shall be allowed to be prepared at site. It should be casted in the stringent atmospheric & pre-defined condition, as per approved QAP as by Engineer In charge. (Make: Fuji or equivalent)

Providing & laying factory made Precast Perforated Lid having length of 500 mm, width 732 mm suitable for placing on U - Shape Drain (DUSD) sizes 600 mm x 600 mm (in to in) thickness of 145 mm respectively. Lid should have T-25 load carrying capacity – 10 T Axle Load – 5 T Wheel Load, confirming to JIS & meeting IS requirements having High Performance Self Compacting Concrete of M-40 cylinder strength/ M-50 cube strength. The Fe 500/ Fe500D shall be used for reinforcement. The Perforated lid unit should have 15 slits each of 120 mm X 20 mm slit for storm water intake.Each lid may have in-built, specially designed lifting inserts of appropriate load carrying capacity and fixed at specific location to avoid the tilting of the lid for safe & fast installation. In no case the casting shall be allowed to be prepared at site. It should be casted in the stringent atmospheric & pre-defined condition, as per approved QAP as by Engineer In charge. (Make: Fuji or equivalent)

Providing and Laying of factory made precast Box Culvert having 500 mm Width X 500 mm Height in to in dimension , units of 2000mm length, confirming to Japanese Industrial Standards (JIS) & meeting IS requirements, made by using advanced Japanese Technology having High Performance Self Compacting Concrete of M40 Grade cylinder strength/ M50 Grade cube strength and using Fe 500/Fe 500D reinforcement bar designed for 5 T wheel Load with 0.2 m to 3 m earth cushion above it. Product also includes, groove for fixing rubber gasket, flange coupling jointing arrangements and special in-built hanging brackets at appropriate locations for faster & safe installation of the product. In no case the casting shall be allowed to be prepared at site. It should be casted in the stringent atmospheric & pre-defined condition,including making cut-outs, core cutting for utility ducts as per approved QAP as by Engineer In charge. (Make: Fuji or equivalent)

Providing & Fixing of factory made Silvertech brand Precast Chamber, having size (in to in) of 800 mm (L) X 800 mm (B) X Height :800 mm T-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to Japanese Industrial Standards (JIS) & meeting IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & Fe 500 /Fe 500 D shall be used for reinforcement. The contractor shall prepare & provide the base using PCC/Foundation concrete as a levelling course as per drawing / as recommended by the consultant depending upon the foundation soil strata. The precast Chamber unit should consist of special in built insert of suitable load carrying capacity at appropriate location for fixing De-shackle (Hanging hole) for safe & fast mechanical installation.Hole should be provided at site (No Factory) for connection at the waffle side of chamber as per the site requirement.The Precast cover having size 944 x 944 X 120 mm thick, designed for T-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to Japanese Industrial Standards (JIS) & meeting IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & Fe 500 / 500D shall be used for reinforcement. Cover should have hole of conical shape of 50 mm to 30 mm respectively for storm water intake. The lid may have in build specially designed lifting inserts of appropriate load carrying capacity & fixed at specific location to avoid the tilting of the lid for safe & fast installation.In no case the casting shall be allowed to be prepared at site. It should be casted in the stringent atmospheric & pre-defined condition, including making cut-outs, core cutting for utility ducts as per approved QAP as by Engineer In charge. (Make: Fuji or equivalent)

Providing & Fixing of factory made Silvertech brand Precast Chamber, having size (in to in) of 1000 mm (L) X 1000 mm (B) X Height :1200 mm T-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to Japanese Industrial Standards (JIS) & meeting IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & Fe 500 /Fe 500 D shall be used for reinforcement. The contractor shall prepare & provide the base using PCC/Foundation concrete as a levelling course as per drawing / as recommended by the consultant depending upon the foundation soil strata. The precast Chamber unit should consist of special in built insert of suitable load carrying capacity at appropriate location for fixing De-shackle (Hanging hole) for safe & fast mechanical installation.Hole should be provided at site (No Factory) for connection at the waffle side of chamber as per the site requirement.The Precast cover having size 1144 x 1144 X 150 mm thick, designed for T-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to Japanese Industrial Standards (JIS) & meeting IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & Fe 500 / 500D shall be used for reinforcement. Cover should have hole of conical shape of 50 mm to 30 mm respectively for storm water intake. The lid may have in build specially designed lifting inserts of appropriate load carrying capacity & fixed at specific location to avoid the tilting of the lid for safe & fast installation.In no case the casting shall be allowed to be prepared at site. It should be casted in the stringent atmospheric & pre-defined condition, including making cut-outs, core cutting for utility ducts as per approved QAP as by Engineer In charge. (Make: Fuji or equivalent)

SANITARY FIXTURE & FITTINGS Providing and fixing wsh down water closet (European type, W.C. Pan) with integral P or S trap including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover to be measured and paid for separately)(A) vitreous China Pattern :(i) in white colour

Providing and fixing 12.5 Litres high level C..I. flushing cistern with A pair of C.I. or Mild steel brackets, womplete with fittings such as syplionic arrangement, 15mm nominal size brass ball valve with polythene float, lever G.I. China (60 cm. ) and pull union and couplings for connections with inlet, outlet and overflow pipes etc. including cutting holes in walls and making good the same (overflow pipe to be measured and paid fo separately )

Providing and fixing in position with clamps etc. 32mm nominal internal diameter galvanised steel tube flush pipe for high level flushing cistern including connecting the flush pipe with cistern and closet and making good the walls and floors.

Providing and fixing G.I. inlet connection for flush pipe with W.C. Pan

Providing and fixing plastic seat and cover for wash down water closer with C.P. brass hinges and rubber buffers. (B) Black plastic seal and cover.

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. brackets painted white including sutting holes and making good the same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) In white colour.

Providing and fixing C.P. brass waste for washbasin or sink. (A) 32mmdia.

Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers.

Providing and fixing toilet paper holder.(A) C.P. Brass

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (i) 15mm dia.

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. (i) 15mm dia.

Providing and fixing Urinal of approved quality including connection with trap and with integral longitudinal flush pipe.(A) Squating plate pattern white earthenware 550mm x 300mm.

Providing and fixing Rubber plug for sink or wash basin.

Providing and fixing chromium plated, bottle trap with necessary couplings of approved quality for wash basin.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing screw down 2-way bib cock of following size. Brass chromium plated 2-way bib cock (i) 15 mm.(Make: Hind ware/cera/jaguar/Grohe)

Concealed Urinal sensor: Supply and installation of sensotronic concealed type Flushing Valve for urinal complete set with installation box with control cock including all consumable, tools, tackles, labour etc all complete as directed by the Bank. (Make: Kohler, Jaquar, Hindware, Parryware or Equivalent)

Providing and fixing Angle tap, capstan head, screw down high pressure with screws, shanks and back nuts. (i) 15mm dia. (Make: Hind ware/cera/jaguar/Grohe)

Providing and fixing 450mm Long Braided Hose pipe with M10X1 Nipple, 15mm Nut, O-Ring & Rubber Washer (Suitable for Wash Basin, Kitchen Sink etc.) of approved make and conforming to Manufacturers Standards.

Supply, storing, installation and testing twin coat hook, fixed to wall / door with concealed CP screws etc. complete. (Make: Hind ware/cera/jaguar/Grohe)

Providing and fixing of grab bars 300 mm Stainless steel in physically disabled toilet including all necessary fitting, SS Screws & Accessories etc.Complted in all manners and satisfied to of EIC.(Make: Hind ware/cera/jaguar/Grohe)

Providing and fixing of grab bars Vertical Swing 18-8 S, type-304, 18-gauge (1mm) stainless steel tubing with satin-finish. 1–1/4 (25mm) outside diameter wall mounted in physically disabled toilet including all necessary fitting, SS Screws & Accessories etc.Complted in all manners and satisfied to of EIC.(Make: Hind ware/cera/jaguar/Grohe)

WATER SUPPLY Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete.[A] 15 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [B] 20 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [C] 25 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [D] 32mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [E] 40mm.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.(Ac Drain)

Providing, fixing, jointing and testing, heavy quality cast steel / Brass ball valve single/double piece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 25mm diameter (Make:ZOLOTO/VTC/SANT)

Providing, fixing, jointing and testing, heavy quality cast steel / Brass ball valve single/double piece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 32mm diameter (Make:ZOLOTO/VTC/SANT)

Providing erecting and fixing double coated SIntex or equivalent PVC. (ISI) water tank of required capacity each with all necessary fittings and connection etc. complete on terrace. (Make: Sintex / Kaka )

Preparing structural design of RCC Under Ground / Partially under ground /above high ground level Reservoir and constructing of required capacity as per relevant I.S. standards in M30 concrete grade with HYSD Fe 500D reinforcement and constructing the same, including excavation in all types of soil strata (including rock) including shoring strutting if required, for loose soil / to protect from collapse, casting 100 mm thick P.C.C. levelling course in M-15, Refilling the pit with proper soil and disposing of the surplus stuff at all lead. Including cement plaster in CM 1:2 with approved water proofing compound to all over inside container (i.e. walls, base, top slab/dome bottom etc. all). Including Soil testing. Including all types of labour and material charges of lowering, laying, erecting / hosting and jointing of pipe assembly to inlet, outlet overflow, washout and bye pass arrangement as per hydraulic design. Providing and fixing accessories, CI Manhole frame and cover, water level indicator, adequate cowl type ventilators or lantern type ventilator with stainless steel jail. RCC chambers for valves. Providing and applying three coats of cement paint / snowcem to the out side face of structure. It also includes satisfactory water tightness test as per relevant I.S. code and painting name of scheme and capacity on the tank as per direction of engineer in charge.

INTERNAL DRAINAGE:- Providing, laying and jointing in true line and level 40mm diameter U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. (Make: prince/ supreme / astral / finolex)

Providing, laying and jointing in true line and level 50mm diameter U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. (Make: prince/ supreme / astral / finolex)

Providing, laying and jointing in true line and level 110 diameter U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diameter x 149 mm length x 145 mm height at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. (Make: prince/ supreme / astral / finolex)

Providing, fixing and testing PVC Deep seal P-Trap of 110 X 110 mm dia diameter, with necessary distance piece of 75mm dia pipe and 150 x 150mm heavy duty PVC three piece grating, making necessary holes and cutting in Slab/Walls, etc complete as per engineer in charge. (Make: prince/ supreme / astral / finolex)

Providing, fixing and testing PVC Height Riser with wings of 110 X 50 X 40 mm dia diameter, with necessary suported accessories, making necessary holes and cutting in Slab/Walls, etc complete as per engineer in charge. (Make: prince/ supreme / astral / finolex)

EXTERNAL DRAINAGE :- Providing and supplying of Class SN8 Structured Wall polyethelene Piping systems (Pipe with online/offline coupler and elastomeric sealing ring) with non-smooth External Annular Corrugated and Smooth Internal Surfaces (Double Wall) for non-pressure underground Sewerage & Drainage application as per EN:13476-3 including all local and central taxes, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to the departmental stores etc. complete.(ID 150 mm diameter)

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps.(B) 150mm x 100mm size P or R type (make-Local )

Providing and fixing, best Indian make 1st quality, salt glazed PVC Sewer (intercepting) trap, of 150 mm. x 150 mm. size with cleaning eye cap and metal stopper chain, set in CC 1:2:4 etc., complete in last manhole including vent / fresh air pipe.

Providing & Fixing of factory made Silvertech brand Precast Chamber, having size (in to in) of 800 mm (L) X 800 mm (B) X Height :800 mm T-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to Japanese Industrial Standards (JIS) & meeting IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & Fe 500 /Fe 500 D shall be used for reinforcement. The contractor shall prepare & provide the base using PCC/Foundation concrete as a levelling course as per drawing / as recommended by the consultant depending upon the foundation soil strata. The precast Chamber unit should consist of special in built insert of suitable load carrying capacity at appropriate location for fixing De-shackle (Hanging hole) for safe & fast mechanical installation.Hole should be provided at site (No Factory) for connection at the waffle side of chamber as per the site requirement.The Precast cover having size 944 x 944 X 120 mm thick, designed for T-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to Japanese Industrial Standards (JIS) & meeting IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & Fe 500 / 500D shall be used for reinforcement. Cover should have hole of conical shape of 50 mm to 30 mm respectively for storm water intake. The lid may have in build specially designed lifting inserts of appropriate load carrying capacity & fixed at specific location to avoid the tilting of the lid for safe & fast installation.In no case the casting shall be allowed to be prepared at site. It should be casted in the stringent atmospheric & pre-defined condition, including making cut-outs, core cutting for utility ducts as per approved QAP as by Engineer In charge. (Make: Fuji or equivalent)

Extra rate for every 200 mm additional depth of precast manhole of size 800x800

Providing laying (to level or slopes) and jointing reinforced concrete pipe Light duty non-pressure pipes I.S. class NP3 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(D) 300mm (upto 10 ton) (Local Make)

RAIN WATER INTERNAL DRAINAGE :- Providing, laying and jointing in true line and level 110 mm diameter U.P.V.C (Type A) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diameter x 149 mm length x 145 mm height at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. (make: Asirvad/ prince/ supreme / astral / finolex)

Providing, Fixing, Installation and Testing of 100mm rainwater outlets 2HP-2W/3HP-2W/ 4HP-2W* are to be ACO Building Drainage HP Two-Way screw outlets with locked flat grating supplied by ACO Building Drainage SG17 5TE. All components to be manufactured from grade LM6 aluminium alloy to BS 1490/ gun-metal to BS EN 1982. complete as per site engineer in charge.

Providing and fixing, PVC cowl, 110mm diameter on PVC ventilating pipes and verticals for soil and waste Pipes at top level / terrace level, as specified and required, etc. complete.

SOCK PIT AND SEPTIC TANK :- (B) Providing sock pit of 5.00 Cu.M. Volume including excavating and filling brickbats with dry masonry work at top for 45cm. height including covering the top with stone including providing vatas in C.M. 1:3 with finishing curing etc. complete as directed. (up to 10 ton)

C.I. cover with frame (Light duty) 455mm x 610mm internal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. )(Local Make)

Providing and fixing cast iron steps of size 500mm x 150mm x 22.5mm and painting with two coats of Anti-corrosive paint etc. complete.

PUMP ROOM :- Supply, fixing and jointing of heavy class GI puddle flange pipes epoxy coated, 50 mm dia and minimum 400 mm long clear ends outside the RCC surface, and fixed in underground sumps, water tanks etc. complete, with end joints either screwed / flanged as required with endcaps / plugs complete as per the requirement of E-i-C (Local Make)

Supply, fixing and jointing of heavy class GI puddle flange pipes epoxy coated, 80 mm dia and minimum 400 mm long clear ends outside the RCC surface, and fixed in underground sumps, water tanks etc. complete, with end joints either screwed / flanged as required with endcaps / plugs complete as per the requirement of E-i-C (Local Make)

Supply, fixing and jointing of heavy class GI puddle flange pipes epoxy coated, 100 mm dia and minimum 400 mm long clear ends outside the RCC surface, and fixed in underground sumps, water tanks etc. complete, with end joints either screwed / flanged as required with endcaps / plugs complete as per the requirement of E-i-C (Local Make)

Providing and fixing electronic type level indicator for water tanks mounting in panel with level display, alarm (level low or high), and manual reset for alarm, potential free set point contacts etc. complete with electrical wiring to probes and all accessories complete the work. Provision to connect to the building Automation system or pump controller through a suitable port.(Make: Wilo)

Supply, installation, testing & commissioning of Submersible Open well single stage single entry pumps with C.I Casing, C.I Impeller and SS Body SS-304 Shaft,connected to TEFC submersible motor for 415 + 10% volts, 1 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphragm and bend, vertical discharge pipe, electrical panel with in built level controller with operational mode as pump working at low level, as well pump at high level with a hooter alarm and cut off at dry level as determined. The pump shall be provided with a lifting devise of pull chain/guide rail & G.I. heavy class rising main of 1.0 m length including interconnecting piping, valves (Ball Valve / Butterfly), Non return valves (GM/CI) 15 m cable etc. as per requirement complete in all respects. (Pumps shall be installed in a set of One pump operation).Electrical Starter panels complete with O/L Relay with Single phasing preventer feature, earth leakage relay, ON-OFF and Trip Indicating lamps, contactors contacts for Building Automation System, interlocking, level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level, cascade operation, working / standby slelction, etc. suitable for the motor H.P. as specified below and with provision for remote P.B. on/off complete as required. The on/off operations for all pumps shall be available on central BMS system Capacity per pump - 0.28 LPS [1 m3/hour], System Flow - 0.55LPS [2 m3/hour], Head:- 15-20 mtr. 2 Nos. Pumps (1 Working + 1standby)

SITC of 250 LPH water ATM with all required accessories and base. Specifications: IOT enabled solar based dispensing water ATM. Automatically dispense both paper glasses and water. IOT enabled online monitoring dashboard integrated with 32" screen on the water ATM. Minimum one year warranty.

SITC of 1 HP, 0.7kw, Horizontal open well submercible pump set for water sculpture as per following specifications. Placement in underground sump inside water body. Single Phase. Flow: upto 1550 LPM. Head: upto 48 m. Power: 0.7kW (1hp). Voltage: 160 to 240 voltage. Material of construction: Impeller : Noryl*/ Cast Iron. Casing : Cast Iron. Motor Body : SS. Minimumm vibration, noise free operationg and long bearing life. Compact Mechanical design. Pump must be CED coated to protect from corrosion. All internal parts must be specially coated to prevent internal rusting. Lower power consumption. warranty of the product must be minimum three years.

SITC of 400mm dia filter with top mount valve for water sculpture as per following specification. Placement in underground sump in water body. Bobbin-wound non corrosice fibre glass reinfored tank with UV resistant. Internal surface of the tank is finished with water resistant resin. Transperant lid for easy inspection at a time of backwash. Spherical tank with uniform wall thickness. High quality oil filled pressure guage. Operating pressure 2.5 bar (testing pressute 4bar). Must be operated under prolong sun light for years. Equipped with a six-position ABS clamp style top-mount multiport valve. Max. temperature of 43 degree. Warranty of the product must be minimum 3years.

IRRIGATION WORKS :- Supply and fixing of flexible tubing and resistance to UV damage and algae growth black in colour 16 mm size. complate with all necessary fittings and connection etc.(16 mm 50 cm 3.8 lph inline lateral) Make: Rainbird / MetsarPlast

Providing and fixing of Drip Lateral fittings of size 16mm with barbed outlets Make: Astore / GF+ / Rainbird

Providing and fixing of Lateral Hold Stake made up HOT Deep GI, 9" in length with slot to hold 16mm lateral at top Make: Astore / GF+

Providing and fixing of PP service saddle of varying size.3/4' complate with all necessary fittings and connection etc. of Make: Astore / GF+

Providing laying and jointing in true line and level of s U.P.V.C. Pipe ( SCH- 40) - 2" for cold water including fittings make supreme / astral / finolex as approved by Engineer In Charge. This includes jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints at operating pressure, including cost of all materials complete as per direction of Engineer-in-Charge.

Providing laying and jointing in true line and level of s U.P.V.C. Pipe ( SCH- 40) - 1" for cold water including fittings make supreme / astral / finolex as approved by Engineer In Charge. This includes jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints at operating pressure, including cost of all materials complete as per direction of Engineer-in-Charge.

Providing laying and jointing in true line and level of s U.P.V.C. Pipe ( SCH- 40) - 3/4" for cold water including fittings make supreme / astral / finolex as approved by Engineer In Charge. This includes jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints at operating pressure, including cost of all materials complete as per direction of Engineer-in-Charge.

Providing laying and jointing in true line and level of s U.P.V.C. Pipe ( SCH- 40) - 1/2" for cold water including fittings make supreme / astral / finolex as approved by Engineer In Charge. This includes jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints at operating pressure, including cost of all materials complete as per direction of Engineer-in-Charge.

Providing and Fixing Ball Valve, 2" with all required fititngs and accessories Make: Finolex / Supreme / Astral

Providing and fixing, 20 mm. dia. UPVC hydrant, for gardening, at required distance, with 20 mm. dia. ball valve of approved make, as recommended or equivalent and UPVC(SCH-40) pipe piece including excavation and PCC for bsae plate and all supporting fittings, making connections with main lines, specials, if required etc. complete with note board "NO DRINKING WATER", as directed

Providing & fixing of 7"Round box with greenlid and corrugated structure with unique shovel access slot and bolt hole knockout complate with all necessary fittings and connection etc. Make: Rainbird / Carson Brooks

Providing and Fixing of Pump Unit with duty point 2.5 LPS @ 25 mtr head with required panel, pressure tank, pressure switch, cables and accessories with 1 working + 1 Standby unit (Make: Lubi / Grundfos / ITT)

Providing, Fixing, Testing & Commissioning of 50 mm '' Disc Filter for a filtering capacity of 12 -20 m3/hr with 120 micron filter element. Make: Rainbird / Amiad

Providing and Fixing of Air Release Valve, 1" with required uPVC riser pipe and fittings with anti bug notch (Make: Bermad)

Providing and Fixing of Automation Controller with 6 schedules per station with all required power connections (Make: Rainbird)

Providing and Fixing of Solenoid Valve, 24V AC with flow control knob Make: Rainbird

ELECTRICAL WORK :- Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories. Cat. III

Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling, complete with earth continuity and necessary connection with primary light with accessories erected on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling complete with 6A Modular type switch and hum free EME four or more step type electronic fan regulator with separately mounted and accessories with earth continuity of following type erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories. Cat. III

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [I] For 6A Plug with 2-1.5 sq.mm Cu. Wire. (a) with medium class Rigid PVC pipe and accessories. Cat. III

[II] For 16A Plug with 2-2.5 sq.mm Cu. Wire - As per description 1.2.3. (a) with medium class Rigid PVC pipe and accessories. Cat. III

[III] For 20A Plug with 2-4 sq.mm Cu. Wire - As per description 1.2.3. (a) with medium class Rigid PVC pipe and accessories. CAT-III

Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling with following type accessories. Cat-III

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge. (3) Two Pin/RJ-11 Telephone Socket. [A] For One Gang. Cat. III

(4) TV Co-axial Socket outlet - As per description 1.2.6. Cat-III

(5) Electronic hum Free four or more steps EME Fan regulator. Cat-III

(7) Blank Plate Single - As per description 1.2.6. cat-III

(8) Modem Jack for Computer Open RJ-45 - As per description 1.2.6. Cat-III

(10) 6/16Amp. Universal socket - As per description 1.2.6. Cat-III

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed. (a) 20 mm

(b) 25 mm - As per description 1.3.2

(c) 32 mm - As per description 1.3.2

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (1) 20 mm

(2) 25 mm - As per description 1.3.4

(3) 32 mm - As per description 1.3.4

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size. (a) with medium class Rigid PVC pipe and accessories. (a) 2 wire 1.5 sq. mm

(b) 2 wire 2.5 sq. mm - As per description 1.4.1

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size. (a) with medium class Rigid PVC pipe and accessories. a. 2 wire 4 sq. mm

(b) 2 wire 6 sq. mm

(i) 4 wire 10 sq. mm

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly - Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. b).RG-6

Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos.of pairs. With necessary connections.[A] 2 Conductor Size 0.5 mm. 2) Two Pairs

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction. [C] CAT - 6

Miniature circuit breaker single pole 6A to 25A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark. Cat-III

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity -(A) 6 to 32 Amp. Cat-III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity. (c)63 Amp. Cat-III

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used). (A) (b) (ii) Single phase 6way SS Double door

(B) (b) (ii) Three phase 6 way SS Double door for single phase outgoing horizontal box - as per description 3.11.5

(B) (b) (iii) Three phase 8 way SS Double door for horizontal single phase outgoing - As per description 3.11.5

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed. (I) 25 Amps. DP-CAT-III

(ii) 40Amps. DP Cat-III

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on 3 phase and neutral 415V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component for following Max. rating erected as directed. (ii) 40 Amps.FP. Cat-III

(iii) 63 Amps. FP Cat-III

Supplying & erecting approved make RCCB + MCB (Electro magnetic type only) working on residual current device having 6 KA short circuit breaking capacity and 30 mAmp. Sensitivity & 30 mili sec. tripping time conforming to IS 12640 test knob facility trip free mechanism operating for rated leakage at nominal ten volt, complete erected including all materials lugs screws etc. completed. [e] 32A to 40 A, 4 Pole Three Phase. Cat-II

[f] 63A, 4 pole Three Phase. Cat-II

Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and operate battery backup 1 channel day clock with 14 memory programme, suitable to operate on 240V + 5%, 16A with, floating contacts Minimum switching setup time 1 minimum & LCD display. Also comporised permanent ON/OFF switching. Programming switches & housed in fire proof thermoplastic enclosure & transperent cover erected as required with necessary connection.

Providing and erecting metallic vetrified danger notice board for MEDIUM VOLTAGE installation to be erected as per I.S

Providing and erecting required size HOT deep Galvanised strip for earthing of H.T. OCB/ ACB/ Transformer LT pannel board, Motors etc. using copper clamp.

Providing and erecting HOT deep Galvanised strip iron wire 8 to 16 S.W.G.

Supplying & erecting in earthpit of minimum bore dia. 225mm size ASH or approved make Safe Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron galvanising, Inner pipe dia of 40 mm having 200-250 Micron galvanising, connection terminal dia of 14 mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications. [B] For Electrical installation up to 11 KV. located in other than normal soil i.e. Soft Rock, Marshy Soil etc. Length of Pipe : 2 mtr. -Back filling Compound :1 no. Bag of 25 Kg.

[C] For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA)i.e. independent Earthing located in other than normal soil i.e. Soft Rock, Marshy Soil etc. - As per description 3.14.10. -Length of Pipe : 3 Mtrs. -Back filling Compound :2 nos Bags of 25 Kg.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. (A) 3 core 2.5 Sq. mm

(B) 3 core 4 Sq. mm - As per description 4.3.2

(C) 3 core 6 Sq. mm - As per description 4.3.2

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. (A-1) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core)

((B) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core) - As per description 4.3.3

(C) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core) - As per description 4.3.3

(D) 3 1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core) - As per description 4.3.3

(E) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core)

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. (b) 4 core 6 Sq. Mm

(c) 4 core 10 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. (d) 4 core 16 Sq. mm (d) 4 core 16 Sq. mm - As per description 4.3.4

(e) 4 core 25 Sq. mm - As per description 4.3.4

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cable. (a) 3 core 2.5Sq. Mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (A) 4 core 2.5 Sq. mm

Supplying following size of Light duty “A” Class G.I . Pipe & erecting as directed by Engineer-in-charge. (A) 25 mm dia

(B) 50 mm dia - As per description 4.5.6

(C) 80 mm dia. - As per description 4.5.6

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (a) 2 to 4 core 2.5/4 Sq. Mm

(b) 2 to 4 core 6 Sq. Mm

(c) 2 to 4 core 10 Sq. mm - As per description 4.6.1

(d) 2 to 4 core 16 Sq. mm - As per description 4.6.1

(e) 2 to 4 core 25 Sq. mm - As per description 4.6.1

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (B) 3 & 1/2 core 35/50 Sq. mm - As per description 4.6.3

(C) 3 & 1/2 core 70 Sq. mm - As per description 4.6.3

(D) 3 & 1/2 core 95 Sq. mm - As per description 4.6.3

(E) 3 & 1/2 core 120 Sq. mm - As per description 4.6.3

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (A) 1.5/2.5/4/6 Sq.mm. - as per description 4.7.1

(B) 10 Sq.mm

(C) 16 Sq.mm.

(D) 25 Sq.mm. - as per description 4.7.1

(E) 35/50 Sq.mm. - as per description 4.7.1

(F) 70 Sq.mm. - as per description 4.7.1

(G) 95 Sq.mm. - as per description 4.7.1

(H) 120 Sq.mm. - as per description 4.7.1

Providing and fixing approved make Perforated C type cable tray. Made from pre- galvanized CR sheet steel. The cable tray should be bended as per IS 2062/1079 . with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification and as per instruction of engineer in charge. (3) 150 X 50 X 1.5 mm Thick

Providing and fixing approved make 'T' Junction for Perforated C type cable tray. Made from pre galvanized CR sheet steel. The Junction should be bended as per IS 2062/1079. with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification and as per instruction of engineer in charge..(3a)150 X 50 X 1.5 mm Thick ' T' Junction

Providing and fixing approved make '90° Elbow' for Perforated C type cable tray. Made from pre galvanized CR sheet steel. The Junction should be bended as per IS 2062/1079. with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification and as per instruction of engineer in charge.. (3) 150 X 50 X 1.5 mm Thick 90° Elbow

Providing and erecting Approved make Ceiling fan with double ball bearing ISI mark with condenser A.C. 23OV.50 c/s.1200 mm. sweep complete, canopy and 30 cms. down rod erected on existing hook or clamp with 24/0.2 , 3 core flexible wire with earthing. [Make shall be approved by Engineer in charge]

Providing 2.5mm.thick laminated sheet to cover the fan hook or Fan box.

Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable for medium duty having following dia size and maximum speed in RPM. [A] 305 mm dia 900 RPM. Cat-II

Supplying & erecting electro galvanised G.I. wire micro mesh jali cover of grade 304 required size with suitable wooden frame duly fitted in wall outside of exhaust fan for insect protection.

Supplying and erecting approved make oscillating type bracket fan A.C. 23OV. 50cy/s 400/450 mm sweep wall mounted with height adjustment and rotary tilting device complete with guard, flexible Core plug top complete erected with lead wires as directed. Cat-II

Providing and fixing approved make Octagonal poles. Made from CR sheet steel. The pole should be made as per IS. and shall be coated with hot dip galvanizing as per IS 2629/4759. with required base plate suitable suspend local wind speed to be erected on existing foundation. (B) 4 Mtr. Long 70 mm Top X 130 mm bottom dia, 3 mm thickness with 200mmx200mmx12mm base plate, 4-M16 Bolts and 600mm long J-bolt.

Pole base suitable for following size of pole fabricated from 4 mm. Thick M.S. sheet with M.S.door having two hinges welded on M.S. flat 25 x 3 mm which is fitted on M.S..base by bolts welded inside the pole base erected with one coat of Red oxide and two coats of Aluminium paint. Outside dimension as per SOR. drawing. (a) Suitable for 90 mm. dia.base of pole

Providing M-20 / 1:2:4 cement concrete foundation & 70 % PCC from bottom including excavation for the pole of size 45 x 45 x 100 cms. Deep in below ground level with plinth of 45 cms x 45 cms (or 45 cms dia x 45 cms) high upper ground level with necessary curing and finishing in approved manner. ( for 4 & 6 mtr pole)

Providing & erecting approved make street light / wall mounting junction box compression moulded from DMC (thermoset plastic) vertical sliding cover having locking with square head stud loop in / loop out in built terminal suitable for four core cable, waterproof of I.P. 54 protected with clamp or bolt nut & earth bolt of following size. [B] 250mm x 194mm x 99 mm

Supplying and erecting approved make online Un-interruptible Power Supply system comprising flat cum-boost charger, static Inverter & sealed maintenance free batteries. The charger having operating capacity for input 160-270V AC & inverter having output 23OV,5O Hz Ac with 0.8 load power factor with battery, over under voltage output with over load & short circuit protection equipment. The system housed in CRC sheet duly powder coated paint with following capacity & with Following size of batteries. (D) 5 KVA with 1hour back up

Providing and erecting AC-3 duty 3 pole power contactor with 2 NO & 2 NC aux contacts complete with 415V/220V operating coil suitable for (L&T, C&S, BCH, TC, Siemense make) (b)- 40 amp.

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA polyester powder coated and high U.V. & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name. 120 to 300 V,Power Factor more than 0.9, THD < 10 %, CCT 4000 K to 6500K, Uniformity ratio >0.7, Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 %. CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/Bridgelux(U.S.A.) make LED used for luminaire. (Each fitting required LM-79 & LM-80 Certificates). (A) Tube Light with integral/ non-integral driver. (d) 20-22 Watts, Surge - 4KV,IP-20, 4 feet. Cat-III

(D) LED Panel Light with provision for Plane front frame with translucent cover fixed to housing complete. © 12-15 watts, 200 x 200 mm, Surge-2 KV. Cat-III

(d) 18 to 20 watts, 250 x 250 mm, Surge- 4 KV. Cat-II

Lowering, laying and jointing HDPE pipes and specials (By butt fusion welding method) including cost of conveyance from stores to site of works at all level including cost of labour, material. (1) 50mm dia

(3) 75mm dia

Lowering, laying and jointing HDPE pipes and specials (By butt fusion welding method) including cost of conveyance from stores to site of works at all level including cost of labour, material. (1) 110mm dia

(4) 160mm dia

(8) 250mm dia

Providing and supplying in standard length ISI mark high density Polyethylene H.D.P.E. Pipes of size HDPE PE100 PN10 as per IS-4984/2016. suitable for underground cable duct ,including of Couplers and endcaps. (1) 50mm dia

Providing and supplying in standard length ISI mark high density Polyethylene H.D.P.E. Pipes of size HDPE PE100 PN10 as per IS-4984/2016. suitable for underground cable duct ,including of Couplers and endcaps. (2) 75mm dia

(4) 110mm dia

(7) 160mm dia

(11) 250mm dia

(13) 315mm dia

Excavation for pipe line trenches for electrical line, manhole etc. all with shoring and struting if required as per required gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the site etc. complete for all lifts and strata as specified. (a) in all sorts of soil and soft murrum. upto 1.5m depth

RA ITEMS : SITC of 4-Way VTPN DB, IP43 metal door. Double door with arrangement for FPMCCB, TPMCBs. Make: Havell's, Legrand, Schneider

SITC of 32A TP MCB, 10kA Short Circuit Breaking Capacity, ‘C’ curve. Make: Havell's, Legrand, Schneider

SITC of 40A TP MCB, 10kA Short Circuit Breaking Capacity, ‘C’ curve. Make: Havell's, Legrand, Schneider

SITC of 63A TP MCB, 10kA Short Circuit Breaking Capacity, ‘C’ curve. Make: Havell's, Legrand, Schneider

SITC of Panels of below ratings as per IS Specifications and respective drawings. The unit rate for each item shall include : Call for final inspection prior to dispatch. Delivery of the panels to site. Shifting of the panels from site store to the suitable location. Fixing of Shipping Section. Assembly and wiring of component supplied separately. Installation of panel to Electric Room including removing packing. Earthing all components, frame etc. to a common internal earth bar. M.S. parts should be painted with powder coating. Supply & Fixing all accessories and supporting structure. Supply & Fixing of M.100 mm. channels for fixing the panels. Connection, Testing & Commissioning. Checking of Internal connection and wiring, operation of switches, starter, TPN MCCB, relays, contractors etc. Supply of necessary tools, hardware, mounting with necessary civil masonary works etc. Electrical Contractor shall carry out the insulation test at site and all the observations shall be recoreded and submitted in duplicate to the consultant or engineer - in - charge. The rate shall include the civil foundation as approved by site enginner. Make: Schnieder, ABB, Siemense, L&T, . NOTE: Panel design might vary as per final working. Contractor must follow the SLD before execution. SITC of Outdoor type Main Section Feeder Panel-1 as per above specifications. Incomer : 160A, FP, TMB MCCB O/L, S/C (16kA) with RHE, Spreaders-Separators. RYB Indicating Lamp- 4 NOS with VSS & Voltmer. Control Fuse - 3 NOS. Multi Function Meter (MFM) - 1 NO. CT 160/5A 3 NOS (for Measuring Current) with ASS & Ammeter. Surge protection device to be considered. Busbar: 160A TPN, 415V,3-Phase 15KA Aluminium. complete with Heat shrinkable sleeve, expoxy support & hardware. Outgoings : 1 no. of 100A FP MCCB, 6 nos. of 63A, FP Microprocessor Based 36KA, MCCB. 1 no. of 40A, FP Microprocessor Based 15KA, MCCB. Panel details might vary as per final design. Contractor must need to follow the SLD and submit the GA drawing to the consultant before ordering.

SITC of Outdoor type Sub-main Feeder Section Panel-1 as per above specifications. Incomer : 100A, FP MCCB TM Based O/L, S/C (16kA) with RHE, Spreaders-Separators. On, off, trip indicating lamp. 6A, 10kA, SP MCBs-3 nos. RYB Indicating Lamp- 4 NOS with VSS & Voltmer. Control Fuse - 3 NOS. Multi Function Meter (MFM) with RS485 & demand- 1 NO. CT 100/5A, 5VA, 3 NOS (for metering) Resin Cast. 6A, 10kA, SP MCB for Control- 6nos. Space heater with thermostate and MCB-1 no. Plug socket & panel light for supply-1 no. Surge protection device to be considered. Busbar: 100A FP, 415V,3-Phase 15KA Aluminium, complete with Heat shrinkable sleeve, expoxy support & hardware.Outgoings : 4 nos. of 63A FP MCB, 2 nos. of 25A, FP MCB. 9 nos. of 10A, DP MCBs. 2nos. digital timer with required accessories. NOTE: Panel details might vary as per final design. Contractor must need to follow the SLD and submit the GA drawing to the consultant before ordering.

SITC of Outdoor type Sub-main Feeder Section Panel-2 as per above specifications. Incomer : 63A, FP MCB. On, off, trip indicating lamp. 6A, 10kA, SP MCBs-3 nos. RYB Indicating Lamp- 4 NOS with VSS & Voltmer. Control Fuse - 3 NOS. Multi Function Meter (MFM) with RS485 & demand- 1 NO. CT 63/5A, 5VA, 3 NOS (for metering) Resin Cast. 6A, 10kA, SP MCB for Control- 6nos. Space heater with thermostate and MCB-1 no. Plug socket & panel light for supply-1 no. Surge protection device to be considered. Busbar: 63A FP, 415V,3-Phase 15KA Aluminium, complete with Heat shrinkable sleeve, expoxy support & hardware.Outgoings : 4 nos. of 25A FP MCB, 10 nos. of 10A, DP MCBs. 2nos. digital timer with required accessories. NOTE: Panel details might vary as per final design. Contractor must need to follow the SLD and submit the GA drawing to the consultant before ordering.

SITC of Outdoor type Sub-main Feeder Section Panel-3 as per above specifications. Incomer : 100A, FP MCB. On, off, trip indicating lamp. 6A, 10kA, SP MCBs-3 nos. RYB Indicating Lamp- 4 NOS with VSS & Voltmer. Control Fuse - 3 NOS. Multi Function Meter (MFM) with RS485 & demand- 1 NO. CT 100/5A, 5VA, 3 NOS (for metering) Resin Cast. 6A, 10kA, SP MCB for Control- 6nos. Space heater with thermostate and MCB-1 no. Plug socket & panel light for supply-1 no. Surge protection device to be considered. Busbar: 100A FP, 415V,3-Phase 15KA Aluminium, complete with Heat shrinkable sleeve, expoxy support & hardware.Outgoings : 1no. 63A, FP, MCB. 4 nos. of 25A FP MCB, 12 nos. of 10A, DP MCBs. 1no. 32A DPELCB, 30mA. 2nos. 25A DP ELCB, 30mA. 1no. 16A DP ELCB, 30mA. 2nos. digital timer with required accessories. NOTE: Panel details might vary as per final design. Contractor must need to follow the SLD and submit the GA drawing to the consultant before ordering.

SITC of Outdoor type Sub-main Feeder Section Panel-4 as per above specifications. Incomer : 63A, FP MCB. On, off, trip indicating lamp. 6A, 10kA, SP MCBs-3 nos. RYB Indicating Lamp- 4 NOS with VSS & Voltmer. Control Fuse - 3 NOS. Multi Function Meter (MFM) with RS485 & demand- 1 NO. CT 63/5A, 5VA, 3 NOS (for metering) Resin Cast. 6A, 10kA, SP MCB for Control- 6nos. Space heater with thermostate and MCB-1 no. Plug socket & panel light for supply-1 no. Surge protection device to be considered. Busbar: 63A FP, 415V,3-Phase 15KA Aluminium, complete with Heat shrinkable sleeve, expoxy support & hardware.Outgoings : 1no. 63A, FP MCB. 4 nos. of 25A FP MCB, 10 nos. of 10A, DP MCBs. 2nos. digital timer with required accessories. NOTE: Panel details might vary as per final design. Contractor must need to follow the SLD and submit the GA drawing to the consultant before ordering.

SITC of Outdoor type Sub-main Feeder Section Panel-5 as per above specifications. Incomer : 63A, FP MCB. On, off, trip indicating lamp. 6A, 10kA, SP MCBs-3 nos. RYB Indicating Lamp- 4 NOS with VSS & Voltmer. Control Fuse - 3 NOS. Multi Function Meter (MFM) with RS485 & demand- 1 NO. CT 63/5A, 5VA, 3 NOS (for metering) Resin Cast. 6A, 10kA, SP MCB for Control- 6nos. Space heater with thermostate and MCB-1 no. Plug socket & panel light for supply-1 no. Surge protection device to be considered. Busbar: 63A FP, 415V,3-Phase 15KA Aluminium, complete with Heat shrinkable sleeve, expoxy support & hardware.Outgoings : 1no. 63A, FP MCB. 4 nos. of 25A FP MCB, 11 nos. of 10A, DP MCBs. 2nos. digital timer with required accessories. NOTE: Panel details might vary as per final design. Contractor must need to follow the SLD and submit the GA drawing to the consultant before ordering.

SITC of Outdoor type Sub-main Feeder Section Panel-6 as per above specifications. Incomer : 63A, FP MCB. On, off, trip indicating lamp. 6A, 10kA, SP MCBs-3 nos. RYB Indicating Lamp- 4 NOS with VSS & Voltmer. Control Fuse - 3 NOS. Multi Function Meter (MFM) with RS485 & demand- 1 NO. CT 63/5A, 5VA, 3 NOS (for metering) Resin Cast. 6A, 10kA, SP MCB for Control- 6nos. Space heater with thermostate and MCB-1 no. Plug socket & panel light for supply-1 no. Surge protection device to be considered. Busbar: 63A FP, 415V,3-Phase 15KA Aluminium, complete with Heat shrinkable sleeve, expoxy support & hardware.Outgoings : 1no. 63A, FP MCB. 4 nos. of 25A FP MCB, 12 nos. of 10A, DP MCBs. 2nos. digital timer with required accessories. NOTE: Panel details might vary as per final design. Contractor must need to follow the SLD and submit the GA drawing to the consultant before ordering.

SITC of Outdoor type Sub-main Feeder Section Panel-7 as per above specifications. Incomer : 63A, FP MCB. On, off, trip indicating lamp. 6A, 10kA, SP MCBs-3 nos. RYB Indicating Lamp- 4 NOS with VSS & Voltmer. Control Fuse - 3 NOS. Multi Function Meter (MFM) with RS485 & demand- 1 NO. CT 63/5A, 5VA, 3 NOS (for metering) Resin Cast. 6A, 10kA, SP MCB for Control- 6nos. Space heater with thermostate and MCB-1 no. Plug socket & panel light for supply-1 no. Surge protection device to be considered. Busbar: 63A FP, 415V,3-Phase 15KA Aluminium, complete with Heat shrinkable sleeve, expoxy support & hardware.Outgoings : 1no. 63A, FP MCB. 4 nos. of 25A FP MCB, 15 nos. of 10A, DP MCBs. 2nos. digital timer with required accessories. NOTE: Panel details might vary as per final design. Contractor must need to follow the SLD and submit the GA drawing to the consultant before ordering.

SITC of Outdoor type Sub-main Feeder Section Panel-8 as per above specifications. Incomer : 63A, FP MCB. On, off, trip indicating lamp. 6A, 10kA, SP MCBs-3 nos. RYB Indicating Lamp- 4 NOS with VSS & Voltmer. Control Fuse - 3 NOS. Multi Function Meter (MFM) with RS485 & demand- 1 NO. CT 63/5A, 5VA, 3 NOS (for metering) Resin Cast. 6A, 10kA, SP MCB for Control- 6nos. Space heater with thermostate and MCB-1 no. Plug socket & panel light for supply-1 no. Surge protection device to be considered. Busbar: 63A FP, 415V,3-Phase 15KA Aluminium, complete with Heat shrinkable sleeve, expoxy support & hardware.Outgoings : 1no. 63A, FP MCB. 4 nos. of 25A FP MCB, 13 nos. of 10A, DP MCBs. 2nos. digital timer with required accessories. NOTE: Panel details might vary as per final design. Contractor must need to follow the SLD and submit the GA drawing to the consultant before ordering.

SITC of Outdoor type Sub-main Feeder Section Panel-9 as per above specifications. Incomer : 63A, FP MCB. On, off, trip indicating lamp. 6A, 10kA, SP MCBs-3 nos. RYB Indicating Lamp- 4 NOS with VSS & Voltmer. Control Fuse - 3 NOS. Multi Function Meter (MFM) with RS485 & demand- 1 NO. CT 63/5A, 5VA, 3 NOS (for metering) Resin Cast. 6A, 10kA, SP MCB for Control- 6nos. Space heater with thermostate and MCB-1 no. Plug socket & panel light for supply-1 no. Surge protection device to be considered. Busbar: 63A FP, 415V,3-Phase 15KA Aluminium, complete with Heat shrinkable sleeve, expoxy support & hardware.Outgoings : 1no. 63A, FP MCB. 4 nos. of 25A FP MCB, 12 nos. of 10A, DP MCBs. 2nos. digital timer with required accessories. NOTE: Panel details might vary as per final design. Contractor must need to follow the SLD and submit the GA drawing to the consultant before ordering.

SITC of IP66, 55-65W(towards Road) & 25W-35W(towards pathway) LED, 3000K,>120lm/W, Light pole with following specification. Upper frame made in sheet aluminium, with quick coupling threaded G 3/4" for fixing to support. Bottom frame in sheet aluminium, removable for access to the wiring and optical compartment. Fixing with 3 screws in stainless steel, equipped of safety cable against accidental falls. Gasket in silicone between the upper and bottom frames. Pure polyester powder coating in Standard Grey Colour. Height – 225mm,Diameter - 420mm,Weight - 6.5Kg, Area Exposed to Wind(S) - 0.05 m2. Power LED Module with Company /brand name printed on PCB with the metal core plate, in compliance with IEC 62031 (Supporting Test Report from UL Authorised Laboratory/Intertek should be submitted. LED Chips of CREE/ NICHIA/ OSRAM/ SEOUL/ LUMILEDS make with Individual LED's Minimum Luminous Flux (lm) - 148lm @ 350 mA (@ 85 °C) shall be used- same should be supported by LED manufacturer's tech sheet . Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection a minimum of 4kV (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA which offersType II/III/IV/V distribtuion. LM80 Reported LED Lifetime is L90@ 50,000hours minimum & Estimated LED Lifetime is L80 @ 100,000 hours(Ta-25°C) minimum.LM 80 report & TM 21 calculation should be submitted to support the same.The Light fixture shall be in compliance with IEC 60598-2-3; IEC 60598-1(Supporting Test Report from UL Authorised Laboratory/Intertek should be submitted). LM79 report also should be submitted from UL Authorised Laboratory/Intertek. Sample should be submitted for approval from concerned architect/consultant. 7.5M height Twin arm Pole Made of mild steel pipe sections 114mm dia.,89mm dia. & Propus Design Brackets which is made of hot dip galvanised mild steel pipe sections 89mm dia.(vertical)-only road side & 60mm dia.(Gradually bent ), to get 750mm arm length(both road & pathway side) & pleasing aesthetics. Provision for Advertisement Banner.Entire pole & bracket shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized(60 microns Minimum ) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size.....

SITC of IP66, 25W-35W 3000K,>120lm/W, Light fitting with pole including following specifications. Upper frame made in sheet aluminium, with quick coupling threaded G 3/4" for fixing to support. Bottom frame in sheet aluminium, removable for access to the wiring and optical compartment. Fixing with 3 screws in stainless steel, equipped of safety cable against accidental falls .Gasket in silicone between the upper and bottom frames. Pure polyester powder coating in Standard Grey Colour. Height– 225mm, Diameter-420mm, Weight-6.5Kg, Area Exposed to Wind(S) - 0.05 m2. Power LED Module with Company /brand name printed on PCB with the metal core plate, in compliance with IEC 62031 (Supporting Test Report from UL Authorised Laboratory/ Intertek should be submitted. LED Chips of CREE/ NICHIA/ OSRAM/ SEOUL/ LUMILEDS make with Individual LED's Minimum Luminous Flux (lm) -148lm @ 350 mA (@ 85 °C) shall be used- same should be supported by LED manufacturer's tech sheet. Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection a minimum of 4kV (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA which offersType II/III/IV/V distribtuion. LM80 Reported LED Lifetime is L90@ 50,000hours minimum & Estimated LED Lifetime is L80 @ 100,000 hours(Ta-25°C) minimum.LM 80 report & TM 21 calculation should be submitted to support the same.The Light fixture shall be in compliance with IEC 60598-2-3; IEC 60598-1(Supporting Test Report from UL Authorised Laboratory/Intertek should be submitted) .LM79 report also should be submitted from UL Authorised Laboratory/Intertek. Sample should be submitted for approval from concerned engineer-in charge. 4.5M height Single arm Pole Made of mild steel pipe sections 114mm dia.,89mm dia. & Propus Design Bracket which is made of hot dip galvanised mild steel pipe sections 89mm dia.(vertical) & 60mm dia. (Gradually bent ), to get 750mm arm length & pleasing aesthetics. After Fabrication, Entire Pole is hot dip galvanized(60 microns Minimum ) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The decorative pedastal to be mounted on a suitable size steel plate.

SITC of IP65, IK04, corrosion resistant 5W LED Shrub Uplighter type light fixture with following specifications. 3000K. Tiltable. LED life time 50000h. Low copper content aluminium housing with a chemical chromatised protection before powder coating, ensuring high corrosion resistance. Stainless steel fasteners in grade 316. Power must be provided to the luminaire through water tight single cable gland supplied with 0.5m 2x0.5sqmm. Outdoor power cable. Durable silicone rubber gasket. High efficiency optical PMMA. Clear toughened glass. Plastic ground spike for garden type. Accessory visor and Remote driver must be included. This luminaire is constant current type and need connecting in series. Connections must be done with IP68 connectors. Contractor has to make pcc foundation base of 150mm dia and 300mm deep (or as per the consultant's detail) for the spike installation. Make: Neri, Ligman, K-lite. Contractor must submit the sample to the consultant/architect or engineer incharge before execution. Fixture warranty must be 3 years minimum.

SITC of IP67, corrosion resistant 10W LED Tree Uplighter type light fixture with following specifications. 3000K. Tiltable. LED life time 50000h. Low copper content aluminium housing with a chemical chromatised protection before powder coating, ensuring high corrosion resistance. Stainless steel fasteners in grade 316. Power must be provided to the luminaire through water tight single cable gland supplied with 0.5m 2x0.5sqmm. Outdoor power cable. Durable silicone rubber gasket. High efficiency optical PMMA. Clear toughened glass. Plastic ground spike for garden type. Accessory visor and Remote driver must be included. This luminaire is constant current type and need connecting in series. Connections must be done with IP68 connectors. Contractor has to make pcc foundation base of 150mm dia and 300mm deep (or as per the consultant's detail) for the spike installation. Make: Neri, Ligman, K-lite. Contractor must submit the sample to the consultant/architect or engineer incharge before execution. Fixture warranty must be 3 years minimum.

SITC of IP68, IK07, 8W LED Underwater Flood Light type light fixture with following specifications. 3000K. Tiltable. LED life time 50000h. Stainless steel grade body and fasteners in grade 316. Cable entry PG11. Cable gland supplied with 2m. 2x1.0sqmm. of outdoor submersible power cable. Durable silicone rubber gasket. Clear toughened glass. Remote driver and IP gear box must be installed. Maximum depth 2 meter. The luminaire must be submerged when operational. Connections must be done with IP68 connectors. Make: Neri, Ligman, K-lite. Contractor must submit the sample to the consultant/architect before execution. Fixture warranty must be 3 years minimum.

SITC of IP65, IK07, weather proof & corrosion resistant 28W LED Wall Bracket Up-Down Light type fixture with following specifications. Square Shape, wide beam angle with symmetrical distribution, 3000k. LED lifetime 50000h. Low copper content die-cast aluminium housing. Stainless steel fasteners in grade 316. Durable silicone rubber gasket. High efficiency optical reflector. Clear toughened glass. Single cable entry. Housing is treated with a chemical chromatised protection before powder coating, ensuring high corrosion resistance. Fixture colour must be as per consultant/architect's approval. Make: Ligman, Simes, Neri. Contractor must submit the sample to the consultant/architect before execution. Fixture warranty must be 3 years minimum.

SITC of IP65, IK07, weather proof & corrosion resistant 11W LED Down Light type fixture with following specifications. Square Shape, open surface, medim wide beam angle with symmetrical distribution, 3000k. LED lifetime 50000h. Low copper content die-cast aluminium housing. Stainless steel fasteners in grade 316. Durable silicone rubber gasket. High efficiency optical reflector. Clear toughened glass. Single cable entry. Housing is treated with a chemical chromatised protection before powder coating, ensuring high corrosion resistance. Fixture colour must be as per consultant/architect's approval. Make: Ligman, Simes, Neri. Contractor must submit the sample to the consultant/architect before execution. Fixture warranty must be 3 years minimum.

SITC of IP65, IK08, 15W LED Open Surface Mounted Bulkhead type Light fixture with following specifications. Shielded, 3000k, LED lifetime 50000h. Low copper content corrosion resistant die-cast aluminium frame and body. Stainless steel fasteners in grade 316. Durable silicone rubber gasket. Impact resistant UV stabilised polycarbonate diffuser. The luminaire is treated with a chemical, chromatised protection before powder coating, ensuring high corrosion resistance. Make: Ligman, Neri, Simes. Contractor must submit the sample to the consultant/architect or engineer incharge before execution. Fixture warranty must be 3 years minimum.

SITC of 4Ft. LED (4000K) Batten with all required accessories and connections. Make: Havell's, Wipro, Crompton. Contractor must submit the sample to the consultant/architect before execution. Make: K-lite, Ligman, Havell's, Bajaj, Wipro. Fixture warranty must be 3 years minimum.

SITC of IP66, weather proof & corrosion resistant GI 10-12 Mtr. High Mast. Suitable for mounting 6 nos. of 240W LED flood lights, 3000K. Motorized brackets for maintenance purpose. Complete installation including required RCC foundation. Approved coloured and coated with epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint. Built in control box with service door with safety lock and chain and with all necessary connection with suitable MCB. Make: K-lite, Havell's, Bajaj. Contractor must submit the sample to the consultant/architect or engineer incharge before execution. Fixture warranty must be of min. 3 years.

SITC of Industrial grade corrision resistant Aluminium turbo ventilator fan for roof with all required fixing accessories. Twin Sealed bearings with self lubricating resin to ensure frictionless rotation even at lowest wind velocity. Permanently Lubricated & Sealed. Turbine diameter 760mm, Neck diameter 610mm. 42 nos of aerofoil Vanes (Blades). Net weight approx. 6kgs.

Liaison fees for preparing necessary documents and drawings for getting N.O.C from Electricity Co. and Electrical Inspector for the installation of 11 KV / 0.433 KV Electrical L.T distribution sub stations. (All statutory fees will be paid by client)

Providing & Fixing of factory made Silvertech brand Precast Chamber, having size (in to in) of 800 mm (L) X 800 mm (B) X Height :800 mm T-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to Japanese Industrial Standards (JIS) & meeting IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & Fe 500 /Fe 500 D shall be used for reinforcement. The contractor shall prepare & provide the base using PCC/Foundation concrete as a levelling course as per drawing / as recommended by the consultant depending upon the foundation soil strata. The precast Chamber unit should consist of special in built insert of suitable load carrying capacity at appropriate location for fixing De-shackle (Hanging hole) for safe & fast mechanical installation.Hole should be provided at site (No Factory) for connection at the waffle side of chamber as per the site requirement.The Precast cover having size 944 x 944 X 120 mm thick, designed for T-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to Japanese Industrial Standards (JIS) & meeting IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & Fe 500 / 500D shall be used for reinforcement. Cover should have hole of conical shape of 50 mm to 30 mm respectively for storm water intake. The lid may have in build specially designed lifting inserts of appropriate load carrying capacity & fixed at specific location to avoid the tilting of the lid for safe & fast installation.In no case the casting shall be allowed to be prepared at site. It should be casted in the stringent atmospheric & pre-defined condition, including making cut-outs, core cutting for utility ducts as per approved QAP as by Engineer In charge. (Make: Fuji or equivalent)

SITC of Stainless Steel Hand Dryer with all required connections and following specifications. Weld-free cover fixed to the base with two safety screws and lock withspecial speedflow key. Aluminium base. Includes silent-blocks to damp mechanical vibrations. Fire resistant plastic UL 94-V0 fan scroll. High-speed motor with safety thermal cut-off.The motor revolutions canbe adjusted manually by the potentiometer. • Aluminium centrifugal double asymmetrical inlet fan wheel. Disconnects automatically after 60 seconds of continuous use. Electronic infrared detection sensor. Adjustable detection by potentiometer(5- 25 cm). Ultra-flat: 10 cm deep (complies with ADA regulations). Make: Jaquar, Kohler

SITC of 2.0 MP 1/2.8" Progressive Scan CMOS , Min. Illumination Color: 0.01 Lux @(F1.2, AGC ON), 0.028Lux @(F2.0, AGC ON); B/W: 0.001 Lux @(F1.2, AGC ON), 0.0028 Lux @(F2.0, AGC ON), 0 Lux with IR Shutter Speed 1/3 s to 1/100,000 s Slow Shutter Yes Auto-Iris No Day & Night IR Cut Filter Digital Noise Reduction 3D DNR WDR 120 dB 3-Axis Adjustment Pan: 0°to 355°, tilt: 0°to 70°, rotate: 0°to 355°, IR Range Up to 40 m Wavelength 850nm, Video Compression Main stream: H.265/H.264 Sub-stream: H.265/H.264/MJPEG, Third stream: H.265/H.264 H.264 Type Baseline Profile/Main Profile/High Profile, H.264+ Main stream supports, H.265 Type Main Profile, H.265+ Main stream supports Video Bit Rate 32 Kbps to 8 Mbps, Audio Compression (-S) G.711/G.722.1/G.726/MP2L2/PCM, Audio Bit Rate (-S) 64Kbps(G.711)/16Kbps(G.722.1)/16Kbps(G.726)/32-192Kbps(MP2L2), TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, PPPoE, NTP, UPnP™, SMTP, SNMP, IGMP, 802.1X, QoS, IPv6, Bonjour

SITC of 4.0MP,  1/2.8" Progressive Scan CMOS,  1920 × 1080@30fps  2.8/4/6 mm fixed lens  Color: 0.01 Lux @(F1.2, AGC ON), 0.028Lux @(F2.0, AGC ON);  H.265+, H.265, H.264+, H.264  120 dB WDR, IR Range Up to 40 m Wavelength 850nm, Video Compression Main stream: H.265/H.264 Sub-stream: H.265/H.264/MJPEG, Third stream: H.265/H.264 H.264 Type Baseline Profile/Main Profile/High Profile, H.264+ Main stream supports, H.265 Type Main Profile, H.265+ Main stream supports Video Bit Rate 32 Kbps to 8 Mbps, Audio Compression (-S) G.711/G.722.1/G.726/MP2L2/PCM, Audio Bit Rate (-S) 64Kbps(G.711)/16Kbps(G.722.1)/16Kbps(G.726)/32-192Kbps(MP2L2), TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, PPPoE, NTP, UPnP™, SMTP, SNMP, IGMP, 802.1X, QoS, IPv6, Bonjour, Behavior analyses, BLC/3D DNR/ROI/HLC,  Built-in micro SD/micro SDHC/micro SDXC, card slot, up to 128 GB, PoE: (802.3af, 36V-57V), 0.2 A to 0.1 A, max. 6.5W, 12 VDC, 0.4 A, max. 5W, Protection Level IP67, IK10,

SITC of 16 Channel NVR DS-7716NI-K4. As per above specification.

SITC of 48 Channel NVR. - as per specification in item no. 390.

SITC of 6 TB Hard drive. MAKE: SEGATE

SITC of 4U rack with all required accessories.

SITC of 16 Port POE Switch. With following specifications; 16x10/100 mbps RJ-45 posrts. 2 RJ-45 gigabit ethernet uplink ports. 2SFP gigabit ehternet fibre optical uplink ports. Power upto 16 POE Cameras. Rack mount compatible. LED's to provide status feedback. 7.2 gbps switching capacity. IEEE 802.3AF/AT complaint + UL listed. CSMA/CD complaint. Half duplex/Full duplex. TENDA/TPLINK/NETGEAR

SITC of 32" display with following specifications. Screen Size 32 Inches Screen Resolution-1366 x 768 Pixels. Display Quality-HD Ready. LED Lighting Type-Backlit. USB 2.0, HDMI, Ethernet ports. 1 x PC Audio In (Mini Jack), 1 x RF In (Terrestrial/Cable Input), 1 x (Common Use for PC Audio in) DVI Audio In (Mini Jack). 2 Built-in Speakers, Down Firing + Full Range. Wide colour enhancer. Minimum 3 years of warranty. MAKE: Samsung

SITC of 55" display with following specifications. Screen Size 55 Inches Screen Resolution-1920 x 1080 Pixels. Display Quality-HD Ready. LED Lighting Type-Backlit. USB 2.0, HDMI, Ethernet ports. 1 x PC Audio In (Mini Jack), 1 x RF In (Terrestrial/Cable Input), 1 x (Common Use for PC Audio in) DVI Audio In (Mini Jack). 2 Built-in Speakers, Down Firing + Full Range. Wide colour enhancer. Minimum 3 years of warranty. MAKE: Samsung

SITC of 24 Port Layer- 2 Switch with following specifications. 24 RJ-45 connectors for 10BASE-T/100BASE-TX/1000BASE-T with 4 shared Gigabit SFP slots Console port. Auto medium dependent interface (MDI) and MDI crossover (MDI-X). Auto negotiate/manual setting. RPS port for connecting to redundant power supply unit. Switching capacity up to 48 Gbps, nonblocking. Forwarding rate upto 35.7 mpps. Built-in web user interface for easy browser-based configuration (HTTP/HTTPS). MAKE: TENDA/TPLINK/NETGEAR

SITC of Camera Box ipv 66 DS-1280ZJ-XS

SITC of Network DB

SITC of IP65 Wifi Access point with following specifications. WiFi Standards IEEE 802.11 a/b/g/n/ac (Wave-2). WEP, WPA/WPA2-PSK, WPA/WPA2 Enterprise (TKIP/AES), Port Forwarding, DHCP Reservation, Roaming, Band Steering, ACL (Layer2), Rate Limit, WLAN Scheduling, DNS Filtering, Client Isolation, Hotspot, Captive Portal. Up to 16 per Access Point (8 per Radio) 4 x Internal Omni-Directional Antennas ETHERNET 3 x 10/100/1000 Base-T with One PoE In 802.3af/at) port USB 1 x USB 2.0 MAKE: Ubiquiti/CAMBIUM/QUANTUM

SITC of Wifi supported POE Switch with following specifications. As per WiFi Standards IEEE 802.11 a/b/g/n/ac (Wave-2). Rack mount compatible. LED's to provide status feedback. 7.2 gbps switching capacity. IEEE 802.3AF/AT complaint + UL listed. CSMA/CD complaint. Half duplex/Full duplex. 2SFP gigabit ehternet fibre optical uplink ports. MAKE: AECONNECT/NETGEAR/TP-LINK

SITC of Computer System including 17" monitor. CPU with 8GB RAM, 2TB HDD, Memory graphic card, DVD writer, minimum 6 nos. USB ports, 2 nos. ethernet ports, HDMI, VGA ports. Keyboard. Mouse. Make: Dell, Lenovo, Toshiba

SITC of 24 core armoured optical fibre cable. Make: BTL

SITC of Media Converter (Pair). MAKE: DBC/TPLINK/NETGEAR

SITC of Grandstream-4 Incoming Line SIP/IP Extension. MAKE: Grandstream/PANASONIC/MATRIX

SITC of Grandstream IP Phone. MAKE: Grandstream/PANASONOC/MATRIX

Installation & Configuration of the CCTV & Wifi system.

Spacers for the maintaining space between the HDPE conduit pipe

Providing & Fixing of factory made Silvertech brand Precast Chamber, having size (in to in) of 1000 mm (L) X 1000 mm (B) X Height :1200 mm T-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to Japanese Industrial Standards (JIS) & meeting IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & Fe 500 /Fe 500 D shall be used for reinforcement. The contractor shall prepare & provide the base using PCC/Foundation concrete as a levelling course as per drawing / as recommended by the consultant depending upon the foundation soil strata. The precast Chamber unit should consist of special in built insert of suitable load carrying capacity at appropriate location for fixing De-shackle (Hanging hole) for safe & fast mechanical installation.Hole should be provided at site (No Factory) for connection at the waffle side of chamber as per the site requirement.The Precast cover having size 1144 x 1144 X 150 mm thick, designed for T-25 load carrying capacity - 10 T Axle Load - 5 T Wheel Load, confirming to Japanese Industrial Standards (JIS) & meeting IS requirements, having High Performance Self Compacting Concrete of M-40 cylinder strength/M-50 cube strength & Fe 500 / 500D shall be used for reinforcement. Cover should have hole of conical shape of 50 mm to 30 mm respectively for storm water intake. The lid may have in build specially designed lifting inserts of appropriate load carrying capacity & fixed at specific location to avoid the tilting of the lid for safe & fast installation.In no case the casting shall be allowed to be prepared at site. It should be casted in the stringent atmospheric & pre-defined condition, including making cut-outs, core cutting for utility ducts as per approved QAP as by Engineer In charge. (Make: Fuji or equivalent)

Extra rate for pre-cast in M-50 chamber for every additional depth of 0.1 M GR part there of over above item (I) For depth Above 1.0M to 2.0M

Ms Natvar Construction Co.