SPL REPAIR TO JCOs/OR MD ACCN NO P-298 AT NAGDA ENCLAVE OF JAK RRC AND PROVN OF OVERHEAD SHED OVER UTENSIL WASHING AREA IN 09 X COOK HOUSES IN THE AREA OF AGE B/R-II UNDER GE (WEST) JABALPUR

Amount

M&L for taking up or down, 20mm bore, existing steel tubing and connections including cleaning for refixing or removal to stores complete all as specified and as directed

M&L for taking up or down, 15 mm bore, existing steel tubing and connections including cleaning for refixing or removal to stores complete all as specified and directed

Dismantling of water tanks of capicity 500 ltrs to 1000 ltrs and removing to store complete all as specified and as directed

Removing old tar felt, all loose dirt,old roof tiles,including taking down cement plaster cleaning the concrete surface including removal & cleaning of vegetation, fungus,moss small trees etc from the roof top with wire brush, removing the strips of lightening conductor including refixing the same after repair work complete all as specified and as directed.

Taking down chowkats or frames with shutter without taking off shutter from the frame of size exc 1.5 Sqm but n.exc 4.00 sqm each and removing from site complete all as specified and as directed.

Taking down chowkats or frame with shutters without taking off shutters from the frame of size n.exc 1.5 Sqm each (Wooden/PVC Door, steel window/Ventilator ) and removing from site complete all as specified and as direct

Taking down Shutters of any description and any size complete all as specified and as direct

Taking down shutters of any description exc 1.00 sqm but n.exc 2.00 sqm each resecuring, easing , adjusting and re-fixing in same opening after minor repairs including all necessary fittings complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry built in cement mortar incl all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Dismantling of Stone slabs and kota stone,Cuddappa stone, Granite, Chequered tiles, Paver block, etc of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and as directed.

Dismantling of floor hearth or wall tilling including cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor or pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed.

Supply & laying of CPVC pipes 20 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors including chase cutting and fixing with solvant suitable for CPVC pipe and brass threaded fittings for fixing taps and valves, complete all as specified and as directed.

Supply & laying of CPVC pipes 25 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors including chase cutting and fixing with solvant suitable for CPVC pipe and brass treaded fittings for fixing taps and valves, complete all as specified and as directed.

M&L for 10 mm thick rendering on fair faces of brick or concrete surfaces of wall in CM 1:6,with white sand only from narmda river, including taking down old plaster,complete all as specified and as directed

M&L for 5 mm thick rendering on fair faces of brick or concrete surfaces of ceiling in CM 1:3,with white sand only from narmda river, including taking down old plaster, complete all as specified and as directed

Material and labour for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings .complete all as specified and as directed. (Note: Payment for providing grooves shall be made separately)

M&L for three layered Rotational moulded polyethylene water storage tanks capacity 1000 ltrs(cylindrical vertical with closed top) hoisted and fixed in position including cover complete all as specified and as directed.

S&F for 20 mm dia Ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

M&L for 10mm thick rendering on fair faces of brick or concrete surfaces in CM 1:4 mixed with water proofing compound @ 3 % by weight of cement on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc,including taking down old plaster, white sand only from narmda river, complete all as specified and as directed. (Note-WPC shall be measured and paid separately)

Applying evenly a coat of blown type bitumen at the rate of 0.30 kg per square metre complete all as specified and as directed.

M&L for 3mm thick APP based polymeric membrane minimum weighing 3kg/sqm and minimum reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced application complete all as specified and as directed.

Applying two coats of aluminum paint on top of membrane @ 0.20Kg/Sqm complete all as specified and as directed.

S & F for 125x60mm Pressed steel frames made of 1.25 mm thick MS Sheet size for doors, with double rebates including necessary fixing lugs, hinges, lock strike plate etc,including providing PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) to fill the frame & making good complete all as specified and as directed.

S & F for 105x60mm Pressed steel frames made of 1.25 mm thick MS Sheet size for doors, with single rebates including necessary fixing lugs, hinges, lock strike plate etc, including providing PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) to fill the frame & making good complete all as specified and as directed.

S&F for 35 mm factory made shutters of second class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated supplied and fitted to chowkat complete all as specified and as directed.

M&L for 35 mm thick 2nd class hard wood glazed/gaused and skelton door shutter, factory made, open rebated and prepared to receive glass/guage etc. (without sash bar) edge of frames plain, chamfered or rounded, fitted with cut & mitred beads for securing glass/guage etc size of member as specified in SSR Part I Section 8 clause 8.24(a) and fixed to chowkat including stainless steel wire mess complete all as specified.

M&L for cement concrete type B1 1:2:4 (using 20mm graded stone aggregate) as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs,Hold fast and similar works water troughs and the like including weathering, slightly rouinded for chamfered angles and necessary formwork complete all as specified and as directed

S & F for Factory made internal PVC door frame of size 50x47mm single rebated made out of extruded 5 mm PVC foam sheet, mitre cut at two corners and jointed with 02 Nos of 150 mm brackets of 15x15 mm MS square tube. The two vertical door profiles are to be in forced with 40x20 mm MS tube of 19 gauge through out the frame complete all as specified and as directed.

S&F, for Factory Made Solid PVC Moulded Door Shutters with wood free EPS 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face with particle board core, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

S&F for 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed

M&L for 200mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

M&L for 150 mm long aluminium anodised handles, oval type, stove enamelled black complete all as specified and as directed.

S&F for 75mm long Butt hinges of extruded aluminium alloy, and fixed complete all as specified and as directed.

M&L for 150 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F in repairs 140 mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor complete all as specified and as directed.

S & F for stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples in window, ventilator complete all as specified and as directed.

S&F for powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

S&F for powder coated aluminium door,window and ventilator shutters, fixed type without sash bar, aluminium section weighing on site(only aluminium section), including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and as directed.

M&L for 4 mm thick Sheet glass, ordinary quality and glazing with rubber beads in square n exc 0.5 sq. m in each pane,complete all as specified and as directed.

M&L for Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and as directed.

M&L for 20-25mm thick Machine cut cudappa stone slab as in Shelf/cooking platforms, and like including cutting and fixing over and including 15mm thick cement screed base in CM (1:4) and jointed to support granite top complete all as specified and as directed.

M&L for zed granite Black Work 18 to 20 mm thick (table rubbed and polished ) as in cooking platforms, and like over 15mm thick cement screed base in CM (1:4) including pointing with white cement (1:2) using marble dust with admixture pigment to match with shade of slab and rounding to edges complete all as specified and as directed.

M&L for Granite tiles 18 to 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 15 mm thick screed bed of CM (1:4) , as in tread and riser of staircase,steps , jambs, pillars, window- cills, complete complete as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete as specified and as directed.

M&L for 20-25mm thick Machine cut kota stone slab flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, over and including 15 mm thick Screed bed or bedding layer in cement mortar(1:6), for steps,floor, including rubbing and mirror polishing complete all as specified and as directed

M&L for 20-25mm thick Machine cut kota stone slab as in riser of steps, skirting, dado and pillar, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, over and including 10 mm thick rendering in cement mortar (1:4), on fair faces of brick work or concrete surface as backing, including rubbing and polishing complete all as specified and as directed

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed.

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed.

M&L for non skid coloured ceramic tiles size of tiles 450x350/300x600x7mm thick vertical surface such as in skirting/dado etc over and including 10 mm thick rendering in CM 1:4, complete all as specified and as directed.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting,dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over including 10 mm thick rendering in cement mortar (1:4) complete all as specified and as directed.

M & L for 25 mm thick PCC 1:2:4 type B-0 using 12.5mm crushed stone aggregate as in leveling course Iincluding demolition of existing PCC complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F in repair mild steel, Framed work such as railings, gratings, doors,etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S & F for frame work such as window grill, grating etc of square bars, flat iron with ends bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors and similar work confirming to Fe 290 Gde E-165 complete all as specified and as directed.

M&L for 50 mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) laid in panels surface finish even and smooth using extra cement as in plinth protection, hard standing and similar works, complete all as specified and as directed.

M&L for Brick work using old size bricks with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel and iron surfaces of any description not otherwise described over 10 cm width or girth including preparation complete all as specified and as directed.

M &L for applying one coat of synthetic enamel paint of any tint on old painted steel surfaces of any description not otherwise described over 10cm width or girth including complete all as specified and as directed.

M & L for applying two coats of synthetic enamel paint over one coat of pink primer on new or previously untreated wood surfaces of any description not otherwise described over 10 cm width or girth including preparation complete all as specified and as directed.

M&L applying one coat of synthetic enamel paint on old wood or wood based surfaces of any description over 10 cm width or girth including preparation complete all as specified and as directed.

Complete removal of existing treatment of wall/ceiling surface complete all as specified and as directed.

M&L for applying a coat of chalk whitening primer over 2 mm thick wall care putty to get smooth and even surfaces of wall on New or old plastered wall surfaces of wall including preparation complete all as specified and as directed.

M & L for applying one coat of oil bound distemper complete all as specified and as directed.

M & L for subsequent coat of oil bound distemper complete all as specified and as directed.

M & L for applying three coats of white wash on New plastered surfaces of ceilig complete all as specified and as as directed.

M & L complete removal of existing treatment of ceiling and applying two coats of white wash over a coat of primer complete all as specified and as directed.

S&F in repair vitreous china wash basin white flat back size 550x400 mm with peddestal, including, sawn neck pillar tap, 32 mm dia CP waste coupling and PVC waste pipe 610 mm long and brackets.

S & F in repair water closet (Squat Pattern) complete including provn of lime concrete bedding Orissa pattern size 580 x 440mm white with integral foot rests (excluding flushing cisterns) including connection to trap and flushing pipe anti syphonage pipe etc complete and making good to floor to match with existing complete all as specified and directed.

S&F in rep Vitreous China wash down water closet pan (pedestal pattern), white fixed as in repair with all required fittings,complete all as specified.

S & F in repairs PVC High/Low level flushing cistern 10 litrescapacity including all fittings I.e float valve, syphon, flushpipe,brackets all as specified and directed by EIC.

S&F, in repair kitchen sink with drainage board made out of 1mm thick stainless steel with plugs, washers & wastes including CI cantilever bracket & connection union to pipe over all size 915mmx460mm & bowl size 410 x330x160mm complete all as specified and as directed.

S&F in repair 15 mm bore Stop valves/angle cock, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,conceledd,fancy type, screwed both ends for iron pipe or for unions and fixed

Supply only Liquid water proofing compound.

S & F in repairs Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union

S & F in repair PVC connections 15mm dia with PTMT nut on both ends and washers 450mm long all as specified and directed.

S & F in repair 15 mm dia, bib taps cast copper alloy CP with butterfly handle screwed down screwed for iron pipe or for brass ferrule 15mm bore dia all as specified and directed by EIC.

S & F in repair 15 mm dia, fancy type sawn neck bib taps cast copper alloy CP with butterfly handle screwed down screwed for iron pipe or for brass ferrule 15mm bore for sink, dia all as specified and directed by EIC.

S&F PVC (SWR) gully trap 125/110 mm,setting and jointing with solvent cement grating complete all as specified and as directed.

S&F in repair PVC floor trap square type with CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm, complete all as specified.

S&F in repair towel rail 450 mm long of Brass CP fixed with and including chromium plated brass screw and wooden / plastics cleats ( min wt 170 gms)

S&F in repair for stainless steel kitchen plate rack SIZE (24"X36"X10") three tire ISI marked, including all fittings all as specified and as directed by Engineer-in-charge.

S & F in repair of 110 mm dia PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches,floor and wall including taking down old unserviceable pipe any description and any type complete all as specified.

S & F in repairs PVC (SWR) Pipes single socketed in any length with rubberring joints laid in trenches or in floors and wall 75mm bore including taking down old unserviceable pipe any description and any type complete all as specified.

S&F 110mm dia (bore of pipe) PVC bends (any radius), diminishing pieces or tapers (larger bore measured) with cement joints, complete all as specified.

S & F in repairs PVC (SWR) bends 75mm dia bore any radius with access door all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) junction single (Single T) equal or unequal.

S&F in repairs 110mm bore PVC (SWR) junction single (Single T) equal or unequal.

S&F in repairs 110mm bore PVC (SWR) vent cowl.

S&F Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed by Engr-in-Charge.

S&F in repairs Harrison rails, mild steel, anodised aluminium alloy with fixing brackets for each ,stops, rollers etc. complete all as specified and directed.

S&F in rep Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed .

S&F in repair 18/19 mm thick water proof block board of commercial quality Gde-I fixed with screws as kitchen,cup board's shelves etc all as specified and directed

S&F in repair 18 mm thick ply , PVC sheet Prelaminated on one side with approved texture ("Celuca ply of Rajshree make or equivalent in "sintex" as approved by GE) as in kitchen cabinet ( with shelves and partition ) including necessary fittings & fixtures as per manufacture's instrucions complete all as specified and directed by Engr-in-charge

M&L 6 mm thick cover fillets of standard hard board ,40 mm wide and fixing with screws complete all as specified and directed by Engr-in-charge.

S&F, 1st class HW Beads, straight ( 20 mm cross section size) for glazed or gauzed joinery, renewed, including mitres etc., and removing old beads to store (Plain or moulding as requirement) as in cupboard,kitchen etc complete all as specified and directed by Engr-in-charge

S&F 30 mm wide Steel Continous (piano) hinge, steel bright finish or electro galvanised etc complete all as specified and direcated

S&F and in repair 40 mm dia , SS cupboard knobs fixed with nut ,screw and washer of mild steel bright complete

M&L for cement concrete type D2 1:4:8 (40mm graded aggregate) as in sub base of floor 100 mm thick

M&L Cement concrete (1:3:6) type C-2 using 20 mm graded stone aggregate as in sub base, 75 mm thick, complete all as directed by Engr-in-Charge.

M&L Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Material and labour for crushed stone dust/sand filling under floors or in foundations including watering and consolidation complete all as directed by Engr-in-Charge.

Material and labour for 60mm thick machine pressed glossy finish precast concrete interlocking paver block any shape and size & Colour M-40 grade with grey cement and pigment confirming to IS 15658-2006 complete all as directed by Engr-in-Charge.

M&L Cement concrete type C-2(1:3:6) (40 mm graded stone aggregates) in benching, foundations, filling and mass concrete complete all as specified and directed by Engr-in-charge

S&F in rep 75 mm ,Rim latch with two levers, of mild steel body. stove enamelled finish; with brass knob or lever handle and fixed complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard dense soil complete all as speicfied and directed by Engr-in-charge

M&L Mild steel works as in posts and struts,purlin,rafter,truss,Circular pipe, square section, angle iron, flat iron, Nut bolt, etc, cutting tops to shape as directed, drilling holes, all necessary drilling, bolting or riveting, etc; including embeding in concrete and screwing etc. and similar work conforming to Fe-290 Gde E-165 complete all as speicfied and directed by Engr-in-charge

M&L for plain cement concrete type B2,1:2:4 (40 mm graded stone aggregates) as in post holes complete all as speicfied and directed by Engr-in-charge,

S&F in rep Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified

S&F in Repair Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed .

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out,sof/loose soil, as directed by Engineer-in?charge

Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortor for 150 mm internal dia of pipe complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm retrieve from item no.115 complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, retrieve from item no.115 complete all as specified and directed.

Supply, laying and testing of 150 mm inner diameter of double wall corrugated (DWC) high density polethelene pipes(HDPE) and stiffness class-8 (SN-8) with ISI marked (with CML No) with and including all fittings & jointing materials for sewage lineand laid in trenches as specified in IS-16098(Part-2):2013 and as per manufacturer's instruction complete all as specified and as directed. Note:- Bedding of pipe shall not be provided in normal condition and construction methods shall be strictly compiled as per clause no A-4 Annex 'A' of IS 16098(Part-2):2013

S&F SFRC MH Cover with Frame of size Size 900x560 srounded with steel strip 70 x 1.5 mm Reinforced as per manufacturer's design in Manufactured proccess laid over existing Man hole, confirming to IS 12592:2002 HD 20 grade,including reinforcement, complete all as specified and as directed by Engr-in-Charge.Note- Contractor shall provide PV alongwith manufacturer test certificate of SFRC cover.

Supply & providing water proofing treatment with polymeric standard water proofing membrane, Aquaflex of 10 years gurantee for water tightness complete all as specified and described as under:- (a) Preparation of sunken surfaceproviding 10 mm thick rendering in cement mortar 1:4 mixed with WPC @ 2 % by weight of cement and applying one coat of polymeric modified bitumen 85/25 @ 1.2Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/sqm including cleaning surface all as per manufaturer's specification complete all as specified and directed. (b) Supply & providing water proofing with polymeric proofing membran of 3Kg/Sqm HYPERPLAS STANDARD/ MULTIPLAS STANDARD consisting of 100micron HMHDPE film centre core including coating the surface with compatible primer and torch application of membrane with 10cm overlaps as required thereof, complete all as specified and directed (c) GI pipe 40m bore light grade shall be embedded as outlet at the lowest portion for slope on the wall extending upto at least 450 mm beyond the outer wall

Providing and injecting chemical emulsion for Post Constructional Antitermite TreatmentAlong the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling plugging holes etc. in apron

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete

M&L for rolled mild steel works as in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes,Fe-290 (Gde E16) complete all as speicfied and directed by Engr-in-charge,

M&L Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe-410-W (Gde-E250 quality A

Material and labour for 100 mm thickcement concrete type C-2 1:3:6 (40 mm graded stone aggregate) as in subbase etc all as specified and directed.

M&l 40 mm thick Cement concrete type B-1, 1:2:4 (12.5mm graded aggregate)

M&L for rendering(10mm+5 mm) thick on fair faces of brick work or concrete surfaces in CM 1:4 in two layers on external surface even & fair and using integral water proofing compound.

M & L preparation of New plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed by Engineer-in-charge.

M & L for preparation new surfaces of wall and applying two coats of cement base paint including Priming plastered and other surfaces with alkali resistant complete all as specified

Taking down carefully any type point wiring (light, fan, socket bell or power) , complete with fitting such as switches ceiling roses,lamp holders sockets,regulators,call bell light fitting with PVC conduit surface /concealed or wooden pattens including sunken cast iron /pressed steel terminal boxes etc and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces all as specified and directed by Engineer in charge.

Taking down carefully Main switch and Distribution boards any make and size .

Taking down carefully ceiling fan/Exhaust Fan of any sweep and size and depositing to MES store and Hanging only ceiling fan (M.D.supply) and connecting up including provision of cable from ceiling rose or connector to fan

Taking down carefully Old unserviceable any type sub main wiring with wooden batten/PVC surface conduit of any size and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified and directed by Engineer in charge.

M/L for Sub Main Wiring two single core PVC insulated cable of size 6.0 Sqmm multistranded copper conductor two run drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 25mm dia with all conduit fitting,fixing accessories and one run of 6.0 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and directed by Engineer in charge Note :-Two Nos of 6.0 Sqmm Wire and one No of 6.0 Sqmm Earth wire in One RM length Measured as one unit length.

M/L for Sub Main Wiring with two single core PVC insulated cable of size 4.0 Sqmm multistranded copper conductor drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 20mm dia with all conduit fitting,fixing accessories and 4.00 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and directed by Engineer in charge Note :- Two Nos of 4.00 Sqmm Wire and One No of 4.00 Sqmm Earth wire in One RM length Measured as one unit length.

M&L for Point wiring with PVC insulated 1.5 sq mm multi stranded copper conductor cable 1100 volts grade drawn into and including concealed PVC conduit not less than 20mm (ISI marked) including all fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes duly painted with two coats of antirorrrosive paint outside and two coats of aluminium paint inside, 2.8mm thick hylam brand laminated white bakelite sheet cover for mounting of switches, sockets, fan regulators etc and PVC insulated 1.5 Sqmm multistranded copper conductor cable as earth wire and making good the disturbed surfaces to match with the existing surfaces complete all as specified and directed by Engineer in charge.

(a) One light point/Bell point controlled by one switch.

(b) One fan point controlled by one switch.

(c) One socket point controlled by one switch on same board.

(d) One socket point controlled by one switch on Independent board.

Description all as per item No 7 here in befor but with 1100 volts grade copper standard conductor cable of size 2.5 Sqmm with 2.5 Sqmm solid copper conductor PVC for 3 pin switch socket outlet15 Amp independent board complete all as specified and directed by Engineer in charge .

S & F in repair for bell ding dong AC 230 volts single pole one way complete all as specified and directed by Engineer in charge.

S & F in repair for Switch piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed by Engineer in charge.

S & F in repair for Socket outlet 3 pin, 5 Amps and AC 230 volts flush type complete all as specified and directed by Engineer in charge

S & F in repair for switch socket combination 3 pin 5 and 16 Amps AC 230 volts flush type complete all as specified and directed by Engineer in charge

S & F in repair for Ceiling rose surface bakelite 65 mm x50 mm three terminal AC 230 volts flush type complete all as specified and directed by Engineer in charge

S & F in repair fan regulator Step type of polycarbonate complete all as specified and directed by Engineer in charge.

Supply and fixing in repair of LED lamp rotary type/holder type of 9 watt all as specified and directed by engr-in-charge.

Supply and fixing in replacement of decorative wall light fitting WITH LAMPS 12 WATT made up of Polycarbonate , City-1 , Cylindrical shape , with LED lamp 9 Watt complete with fixing arrangements on wall all as specified and directed.

Supply & Fixing Smart bright Batten Series, LED luminaire using LED 22 watt 110 Lumens/watt with diffuser which ensures uniform distribution and comfort, batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminium housing, Energy efficient, Flicker free start Inbuilt driver unit, Suitable for wall and ceiling mounting using brackets with and including the luminaire testing on completion as per Standard Specification IEC 60598-2-1 / IS: 10322(Parts/Secl),

S & F in repair of LED Decorative /mirror light fitting 10watt along with fixture Surface mounted suitable for indoor aplication , connector block, etc . Complete with all accessories internally pre-wired and including round wood block, connecting up with three core flexible flexible copper conductor cable suitable size complete all as specified and directed by Engineer in charge.

S&F in repair Bulk head endura LED light fitting complete with10 watt LED and making necessary electric connection to ceiling rose with copper conductor of suitable size & length complete all as specified & directed.

Supply & fix in replacement of LED Security Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed.

S & F in repair Sheet metal enclosure DBs Tripple Pole and Neutral 4- way with 200 Amps rated bus bar 415 volts single pole and neutral complete double door complete all as specified and directed by Engineer in charge

S & F in repair MCB TPN 415 volts 63 Amps, C Series complete all as specified and directed by Engineer in charge .

Supply and fixing Single phase ceiling fan 1200 mm permanent magnet brushless DC Motor 230 v 50 Hz single phase 26-30watt rated current 0.16 amp,pf 0.98 370/360 rpm air delivery 220m3 rated service value 629m3/min/watt no of blades three type of blade leaf 1.05 mm thick aluminium sheet remote control radio frequency 5 speed +off timer option speed regulation class of insulation two nos bearings including connecting wire complete with all as required and directed at site by eng in charge

S & F in repair Sheet metal enclosure DBs Single Pole and Neutral 8 way with 200 Amps rated bus bar 240 volts single pole and neutral complete double door complete all as specified and directed by Engineer in charge

Supply and fixing in replacement MCB single pole and neutral 240 volts 40 Amps, B Series complete all as specified and directed by Engineer in charge

Supply and fixing in replacement MCB/Isolators single pole 240 volts upto 40 Amps, B Series complete all as specified and directed by Engineer in charge

Supply & Fixing in repair modular AC box (earth plug socket) complete with 01 number single pole MCB 20 Amps complete all as specified & directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

S & F in repair for bell push piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed by Engineer in charge.

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 300 mm sweep, metallic body complete with Metalic louvers including making holes of suitable size and making good the disturbed surface and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.

Supply , laying and testing cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cables ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 4 core 25 Sqmm complete all as specified and directed by Engineer in charge

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 300 mm sweep, metallic body complete with Metalic louvers including making holes of suitable size and making good the disturbed surface and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.

Supplying and fixing,testing the water heater storage type 25 litres, BEE Five star Rated capacity and after connecting electric and water connection and screwing nuts and bolts , anchor hold fast to fixed on wall and making the good the disturbed surface, complete all as required and as directed at site.Make:Bajaj/Racold/Havells.

Supply,laying & fixing double wall corrugated (DWC) pipes made of high density polythyline (HDPE) with all accessories i.e. all type of joints,Sockets,Elbows,bends and End caps etc.. all as specified and directed by Engr in Charge.of size 50 mm outer dia and 38 mm inner dia of

.Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth , for foundation, etc or for shafts, wells, cesspits, manholes, pier holes,etc. n exc 10sqm on plan and n exc 1.5m in depth and getting out in any type of soil

M/L for Returning , filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

M/L for Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed.

Maa Bhawani Construction (BID ID -3325636)

RP ANAND (BID ID -3335467)

chandra builders (BID ID -3326369)

Rai Construction Co (BID ID -3334950)