Special repair to Bldg No P-1 in Zone III, P-183 to P-184 (Tpt coy ASC) in zone III, Sainik Institute (Bldg No.P-378), Addn/Altn in toilet of 322 Inf Bde and S/R to doors at bldg No. P-278 under GE(S) Jaipur

Amount

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil 13/SR/61SA/BLDG - 40 Sqm

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil. 02/SR/61SA/BLDG - 12 Cum

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25 cm soft / loose soil. 02/SR/61SA/BLDG - 3 Cum

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point . 02/SR/61SA/BLDG - 9 Cum 13/SR/61SA/BLDG - 6 Cum

M&L PCC 1:2:4 type B-1 (20mm graded stone aggregate) as in surface channels and drains. 02/SR/61SA/BLDG - 1 Cum

M&L 75mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection, finished even and smooth without using extra cement. 13/SR/61SA/BLDG - 100 Sqm

M&L 50mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection, finished even and smooth without using extra cement. 02/SR/61SA/BLDG - 20 Sqm

M&L Cement concrete in foundations filling and mass concrete type D-2, 1:4:8 ( 40 mm graded stone aggregates ) 02/SR/61SA/BLDG - 3 Cum 46/SR BLDG/61SA - 1 Cum

M&L 75mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base to floor finished fair & even all as specified and directed by Engineer-in-charge. 02/SR/61SA/BLDG - 170 Sqm 13/SR/61SA/BLDG - 40 Sqm

M&L PCC 1:2:4 mix type B-0 (using 12.5 mm graded stone aggregate ) as in roof kerbs rounded or chamfered on edges. 02/SR/61SA/BLDG - 1 Cum 13/SR/61SA/BLDG - 0.5 Cum 46/SR BLDG/61SA - 1 Cum

M&L Providing cement concrete in lintels upto 1.5 m clear span, cills, steps: seismic and other similar bands, plinth courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, appex 1:2:4 type B-1( 20 mm graded stone aggregates) stones, bed plates as directed. 02/SR/61SA/BLDG - 1 Cum 13/SR/61SA/BLDG - 2.4 Cum

M&L PCC 1:3:6 type C1 as in filling of pressed steel chowkhats complete all as specified . 01/SR/61SA/BLDG - 2 Cum

Extra for forming fair finished drain or channel of manholes inner girth not exceeding 30cm in cement concrete using extra cement including forms, mould mitered stopped ends etc all as specified. 02/SR/61SA/BLDG - 5 RM

Add or deduct from above ser item No.13 for each 25mm girth of part of thereof over 30mm. 02/SR/61SA/BLDG - 2 RM

Cutting holes into or through cement concrete slabs, chajjas, etc. reinforced or otherwise superficial area not exc 100 sq cm 13/SR/61SA/BLDG - 10 Per Cm of depth of cutting

Supply only Integral waterproofing compound 02/SR/61SA/BLDG - 16 Kg

M&L Brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4). 02/SR/61SA/BLDG - 3 Cum

M&L Brickwork with subclass 'B' bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) 13/SR/61SA/BLDG - 4 Cum 46/SR BLDG/61SA - 3 Cum

M&L Brickwork with subclass `B' bricks, straight or curved on plan any radius in half brick thick wall, built in CM (1:4). 02/SR/61SA/BLDG - 1 Sqm

Cutting holes into or through stone wall built in cement lime mortar and wall of cement concrete and making good in CM (1:3) or PCC (1:2:4) type B-1 as required superficial area exc 150 sqcm but n exc 400 sqcm. 02/SR/61SA/BLDG - 10 Per CM of depth of cutting

Cutting holes in stone / brick walls built in CM for inserting hold fast & making good dismantled portion in CM (1:3) depth of embaded portion of holdfast n. exc half brick. 02/SR/61SA/BLDG - 10 Each 01/SR/61SA/BLDG - 200 Each 46/SR BLDG/61SA - 20 Each

M&L Sand stone slabs on manhole covers ,landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and in cement mortar 1:4, complete,5 cm thick. 02/SR/61SA/BLDG - 15 Sqm

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like in CM(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite 13/SR/61SA/BLDG - 3 Sqm 46/SR BLDG/61SA - 5 Sqm

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete. 13/SR/61SA/BLDG - 2 Sqm

M&L 35mm thick 2nd class hard wood factory made Glazed and skelton shutters open rebated & prepared to receive glass gauze etc (without sash bars) edges of framing plain chamfered / rounded fitted without & mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I Section 8 Clause 8.2 (a) supplied & fitted to chowkats. 01/SR/61SA/BLDG - 25 Sqm 46/SR BLDG/61SA - 2 Sqm

M&L 35mm thick 2nd class hard wood factory made plain, framed, panelled shutter (two panel) with lock rail & panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail & steel as per IS:1003 (Part-I) kiln seasoned & chemically pressure treated. 02/SR/61SA/BLDG - 12 Sqm 13/SR/61SA/BLDG - 6 Sqm 01/SR/61SA/BLDG - 60 Sqm 46/SR BLDG/61SA - 10 Sqm

Taking down chowkats or frames not exc. 1.5 Sqm each . 13/SR/61SA/BLDG - 5 Each

Taking down Chowkats or frames exc 1.5 sq. m each with shutters (without taking off shutters from the frames). 02/SR/61SA/BLDG - 10 Each 01/SR/61SA/BLDG - 30 Each

Taking down Chowkats or frames exc 1.5 sqm but not exc 4 sqm each with shutters (without taking of shutters from the frames) 02/SR/61SA/BLDG - 2 Each 01/SR/61SA/BLDG - 12 Each 46/SR BLDG/61SA - 10 Each

Taking down shutters of any description exc 1 sqm and N exc 2 sqm each. 02/SR/61SA/BLDG - 10 Per leaf 01/SR/61SA/BLDG - 16 Per leaf

M&L 28mm thick factory made PVC Supreme Door Shutter consisting of frame made out of m.S. tubes of 19 gauge thickness nd size of 40mmx20mm for stiles, top and bottom rails having a coat of steel primers of approved make and manufacture. M.S. Frame covered with 4mm thick heat moulded "Rajshri" Prelam PVC 'C' Channel of size 28mm thickness,75mm width out of which 60mm shall be flat and 15mm shall be tapered in 45dgree angle on either sides forming stiles, top and bottom rail and 100mm wide Rajshri Prelam PVC sheet out of which 100mm shall be be flat and 15mm shall be tapered An additional of 5mm thick PVC sheet of 20mm width is to be stuck on the interior side of 'C' Channel using PVC solvent adhesive etc. complete on both sides to form lock rail.Lock rail shall be provided on either side of panel. Panelling of 4mm thick PVC sheet to be fitted in the MS Frame welded/sealed to the stiles with 8mm (4mm + 4mm) x 12mm wide PVC sheet as beading on inner side and 8mm (4mm + 4mm) x 20mm wide PVC sheet as beading on the inner tapered side of lock rails joined together with solvent cement adhesive. An additional of 4mm thick PVC sheet of 20mm width is to be stuck on the interior side of 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification and drawing. 02/SR/61SA/BLDG - 3.6 Sqm 01/SR/61SA/BLDG - 24 Sqm

M&L Factory made Adjustable (PVC) Doorframe Manufactured by M/s Rajshri of the size 65mm x 60mm with a wall thicknes of 4mm, made out of extruded 4mm PVC foam sheet, metre cut at two corners and joined with 2nos. of 150mm long brackets of 15 x 15mm M.S. Square tube. The two vertical door profile are to be reinforced with 40 x 20mm M.S. tube of 19 guage through out the frame. The doorframe shall be fixed to the wall using 65/100mm long M.S. Screw through the frame by using PVC fastners. A minimum of 4 nos. of screws to be provided for each vertical member & minimum 2 nos. for horizontal member etc. complete as per manufacturers specification and direction of Engineer-in-Charge. 02/SR/61SA/BLDG - 10 RM 01/SR/61SA/BLDG - 60 RM

S&F 150 mm long Mild steel barrel tower bolt stove enamelled black with bright bolt 02/SR/61SA/BLDG - 30 Each 01/SR/61SA/BLDG - 96 Each

S&F 150 mm long Aluminimum, anodised, barrel tower bolt all as specified. 01/SR/61SA/BLDG - 24 Each 46/SR BLDG/61SA - 30 Each

S&F (length of bolt 300 mm) Mild steel sliding door bolt plate type stove enameled black with bright bolt not less than 12mm dia with & including a minimum of 6 bolt & nut four on bolt plate & 2 on staple plate & fixed. 02/SR/61SA/BLDG - 4 Each 01/SR/61SA/BLDG - 30 Each

S&F 300 mm long Aluminium, anodised sliding door bolt with hasp, and staple bolt type and fixing a clamps of sheet , cast or extruded sections complete fitted all as specified and directed . 01/SR/61SA/BLDG - 12 Each

S&F 100 mm size Butt hinges medium weight cold rolled mild steel. 02/SR/61SA/BLDG - 30 Each 13/SR/61SA/BLDG - 9 Each 01/SR/61SA/BLDG - 174 Each 46/SR BLDG/61SA - 30 Each

S&F MS spring hinges 300 mm, ordinary rat tail rod pattern including roller and roller plate complete fixed to wooden/ angle iron chowkats . 02/SR/61SA/BLDG - 2 Each 01/SR/61SA/BLDG - 16 Each

S&F 125 mm size Mild steel pressed handles oval type stove enamelled black 02/SR/61SA/BLDG - 20 Each 01/SR/61SA/BLDG - 96 Each

S&F 125 mm long Aluminimum , anodised bow handle all as specified. 01/SR/61SA/BLDG - 24 Each 46/SR BLDG/61SA - 30 Each

S&F Overall length of cover plate140 mm aluminium anodised floor door stopper double legged with rubber shoe, fixed to bottom rail of door as directed. 02/SR/61SA/BLDG - 4 Each 46/SR BLDG/61SA - 12 Each

S&F Aluminimum (Die cast ) body door closer hydraulically regulated, designation No 2 universal type , suitable for dooe shutter of 701-850mm in width and of weight between36 to 60 Kg and fixed complete all as specified and directed. 01/SR/61SA/BLDG - 3 Each

S&F Aluminimum (Die cast ) body door closer hydraulically regulated, designation No 3 universal type , suitable for dooe shutter of 851-1000mm in width and of weight between 61 to 80 Kg and fixed complete all as specified and directed. 46/SR BLDG/61SA - 8 Each

S&F Galvanised mild steel wire cloth, 0.56 nominal dia of wire & average width of aperture 1.18mm with tinned tacks, or galvanised wire staples 02/SR/61SA/BLDG - 10 Sqm 01/SR/61SA/BLDG - 15 Sqm 46/SR BLDG/61SA - 6 Sqm

M&L Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; barred iron doors ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165. 02/SR/61SA/BLDG - 50 Kg 01/SR/61SA/BLDG - 40 Kg

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position. 02/SR/61SA/BLDG - 5 KG 46/SR BLDG/61SA - 5 KG

M&L Mild steel angle iron door frame 40x40x6mm conforming to Fe 410.0 incl.12 mm dia deformed bars( Tie bar) for strengthening at bottom of chowkhat incl.cutting floor to accommodate strengthening bar & making good in PCC(1:2:4) type B0. 02/SR/61SA/BLDG - 20 KG

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, & steel peg stay, complete with glazing bars, dovetailed or welded incl. taking down old window 02/SR/61SA/BLDG - 8 Sqm 01/SR/61SA/BLDG - 15 Sqm

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, & steel peg stay, complete without glazing bars, dovetailed or welded incl. taking down old window 02/SR/61SA/BLDG - 8 Sqm 01/SR/61SA/BLDG - 15 Sqm

M&L Steel ventilators with top hung shutters incl hinge steel peg stay complete incl. taking down old ventilator 02/SR/61SA/BLDG - 1.2 Sqm 01/SR/61SA/BLDG - 6 Sqm

M&L Size of frame 125x 60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed 01/SR/61SA/BLDG - 80 RM

M&L Size of frame105x 60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed 01/SR/61SA/BLDG - 20 RM

M&L Running welding in repairs thickness of metal to be welded n.exc 6 mm thick 01/SR/61SA/BLDG - 50 Per 10 RCM

M&L Welding in repairs. Exc 2.5cm but n.exc 5 cm in length and exc 6 mm but n.exc 9 mm thickness of metal 01/SR/61SA/BLDG - 200 each

S&F Powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified complete all as specified and directed. 01/SR/61SA/BLDG - 25 Kg 46/SR BLDG/61SA - 28 Kg

S&F Powder coated (minimum thickness of powder coating 50 micron) aluminimum anodised door/window shutter openale / sliding type with aluminimum section weighing 0.55 kg/mtr incl necessay joining , cleats, glazing clips , rubber packing anodised aluminimum snap beading , screws handle tower bolt etc complete all as specified and directed. 01/SR/61SA/BLDG - 6 Sqm 46/SR BLDG/61SA - 28 Sqm

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall,fixed with self tapping screws as specified. 13/SR/61SA/BLDG - 50 Sqm

M&L 75 mm thick stone patti setting and jointed in CM (1:4) 02/SR/61SA/BLDG - 6 Sqm

M&L Particle board, 19 mm medium density, flat pressed, single layer type or three layer type with BWR type adhesive,fixed with screws to timber frame work 46/SR BLDG/61SA - 18 Sqm

M&L Veneered decorateive plywood, grade 1 (with BWR resin) with decorate face veneers on both faces; fixed with screws to timber frame work 46/SR BLDG/61SA - 18 Sqm

M&L Machine cut kota stone slab flooring 20-25 mm thick over 15 mm thick screed bed in CM (1:4) laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete 02/SR/61SA/BLDG - 30 Sqm 46/SR BLDG/61SA - 10 Sqm

M&L Surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 40mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with WPC @ 3% weight of cement. 02/SR/61SA/BLDG - 353 Sqm 13/SR/61SA/BLDG - 250 Sqm 46/SR BLDG/61SA - 140 Sqm

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. 46/SR BLDG/61SA - 20 Sqm

M&L Coloured Glazed ceramic tiles size 300x450mm x 7mm thick edge cut/ joint free , on walls etc in the combination of light and dark shed concept . set & jointed in neat cement slurry & pointed in white/coloured cement to match over 15mm thick plaster in cement mortar (1:4) Pattern and colour as directed by engineer-in-charge. 02/SR/61SA/BLDG - 100 Sqm 46/SR BLDG/61SA - 30 Sqm

M&L Coloured Glazed ceramic tilessize 300x450mm x 7mm thick edge cut/ joint free , on walls etc. set & jointed in neat cement slurry & pointed in white/coloured cement to match over 15mm thick plaster in CM(1:4) 01/SR/61SA/BLDG - 20 Sqm 04/REV/61SA - 61 Sqm

M&L Coloured Glazed ceramic tiles size 300x450mm x 7mm thick edge cut/ joint free , on walls etc in the combination of light and dark shade concept set & jointed in neat cement slurry & pointed in white/coloured cement to match over 10mm thick plaster in cement mortar (1:4) 13/SR/61SA/BLDG - 100 Sqm

M&L Coloured Non Skid Ceramic tiles joint free 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm , in floors etc, set and jointed in neat cement slurry or tiles addeshive and pointed in white or coloured cement to match over 15mm thick screed bed in cement mortar (1:6) Pattern and colour as directed by Engineer-in-charge. 02/SR/61SA/BLDG - 250 Sqm 46/SR BLDG/61SA - 150 Sqm

M&L Coloured Non Skid ceramic tiles 7 to 8mm thick edge cut/ joint free (squares/ rectangular) area of each tile exc. 0.11 sqm but not exc. 0.18 sqm, in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match over 15 mm thick cement rendering in CM ( 1:6) finished fair and even . 13/SR/61SA/BLDG - 20 Sqm 01/SR/61SA/BLDG - 10 Sqm 04/REV/61SA - 20 Sqm

S&F light shade Vetrified Ceramic tiles edge cut 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM (1:4) . 46/SR BLDG/61SA - 20 Sqm

S&F light shade Vetrified Ceramic tiles edge cut 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster in CM (1:4) on vertical surfaces such as in skirting & dado. 46/SR BLDG/61SA - 5 Sqm

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness , M-35 grade, set with grey cement & pigments, over 25mm thick sand cushion, sides/ ends of tiles shall be protected with CM 1:4,all as directed by Engineer-in-Charge. 13/SR/61SA/BLDG - 40 Sqm

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. 02/SR/61SA/BLDG - 350 Sqm 13/SR/61SA/BLDG - 150 Sqm 01/SR/61SA/BLDG - 30 Sqm 46/SR BLDG/61SA - 30 Sqm 04/REV/61SA - 81 Sqm

M&L 10mm thick Rendering on fair faces of brick work or concrete surfaces in CM (1:3) finished even and smooth without using extra cement in ceiling 02/SR/61SA/BLDG - 200 Sqm 13/SR/61SA/BLDG - 30 Sqm 01/SR/61SA/BLDG - 20 Sqm 46/SR BLDG/61SA - 50 Sqm

M&L 15 mm thick Rendering in CM(1:6) on brick walls or concrete surface, surface finished even and smooth without using extra cement complete all as specified. 02/SR/61SA/BLDG - 400 Sqm 13/SR/61SA/BLDG - 50 Sqm 01/SR/61SA/BLDG - 30 Sqm 46/SR BLDG/61SA - 200 Sqm

M&L 15mm thick Rendering on fair faces of brick work or concrete surfaces in CM (1:4) on walls 04/REV/61SA - 50 Sqm

M&L 15mm thick Rendering in cement mortar 1:4 on stone masonry surfaces or surface other than fair face of brick work of walls, finished fair & even. 13/SR/61SA/BLDG - 30 Sqm 46/SR BLDG/61SA - 100 Sqm

Taking down cement plaster, any description on brick or stone walls, etc. incl. raking out joints, hacking for key, scrubbing down with water, etc. 02/SR/61SA/BLDG - 600 Sqm 13/SR/61SA/BLDG - 100 Sqm 01/SR/61SA/BLDG - 50 Sqm 46/SR BLDG/61SA - 100 Sqm 04/REV/61SA - 50 Sqm

M&L Applying three coats of white wash on new plastered surface of wall including preparation of surface. 02/SR/61SA/BLDG - 200 Sqm

M&L Applying two coats of white wash on old wall surface including preparation of surface 02/SR/61SA/BLDG - 50 Sqm

M&L Preparing newly plastered surfaces including scrapping and applying two coat of Dry distemper all as specified and directed by Eng-in-Charge 01/SR/61SA/BLDG - 30 Sqm

M&L Applying two coats of OBD on newly plastered surfaces of Walls including preparation of surfaces. Over a coat of primer 46/SR BLDG/61SA - 100 Sqm 04/REV/61SA - 50 Sqm

M&L Applying two coats of cement base paint white or tinted on newly plastered surface of wall including preparation of surface. 02/SR/61SA/BLDG - 200 Sqm

M&L Applying Two coats of OBD on newly plastered surfaces of celing including preparation of surfaces. Over a coat of primer 46/SR BLDG/61SA - 50 Sqm

M&L Applying three coats of white wash on ceiling surface including preparation of surface 02/SR/61SA/BLDG - 200 Sqm 01/SR/61SA/BLDG - 20 Sqm

M&L Applying two coats of white wash on old ceiling surface including preparation of surface 02/SR/61SA/BLDG - 30 Sqm

S&F Sheet glass 4.0mm thick, ordinary quality & glazing with oil putty in square n exc 0.5 sq.m in each pane. 02/SR/61SA/BLDG - 15 Sqm 01/SR/61SA/BLDG - 15 Sqm

Hacking out old broken glass any thickness size, quality or description from wooden/steel frames fixed with wooden beads/metal pinning and S&F 3 mm thick sheet glass in squares not exc 0.50 sqm in each pane fixed with wooden beads or putty (in metal frame 13/SR/61SA/BLDG - 5 Sqm 01/SR/61SA/BLDG - 50 Sqm

S&F Figured glass 4.0mm thick, pin head type & glazing with oil putty in squares n exc 0.5 sq.m in each pane 02/SR/61SA/BLDG - 20 Sqm 01/SR/61SA/BLDG - 15 Sqm 46/SR BLDG/61SA - 20 Sqm

S&F 5.5 mm thick glass of ordinary quality and glazing in square including solar control film 25mm micron reflective type sticked to glass panes as per instructions of manufacturers . 01/SR/61SA/BLDG - 18 Sqm

M&L Applying two coats of synthetic enamel paint on wooden surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new surface & applying one coat of pink primer 02/SR/61SA/BLDG - 15 Sqm 01/SR/61SA/BLDG - 200 Sqm 46/SR BLDG/61SA - 20 Sqm

M&L Applying two coats of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new surface & applying one coat of zinc chrome primer 02/SR/61SA/BLDG - 25 Sqm 01/SR/61SA/BLDG - 20 Sqm

Dismantling and taking up or down the existing unserviceable GI pipe and M&L 15 mm bore galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors 02/SR/61SA/BLDG - 15 RM

Dismantling and taking up or down the existing unserviceable GI pipe and M&L 20mm bore galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors 02/SR/61SA/BLDG - 10 Rm

Dismantling and taking up or down the existing unserviceable GI pipe and M&L 25 mm bore galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors 02/SR/61SA/BLDG - 10 Rm

S&F 500 ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantalling old water tank 46/SR BLDG/61SA - 1 Each

S&F 1000 ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantalling old water tank. 02/SR/61SA/BLDG - 2 Each 04/REV/61SA - 2 Each

M&L Providing pre cast cement concrete block or slab 150mm thick 1:2:4 type B1 using 20mm graded stone aggregate with plain or inter locking joints as directed set in CM 1:6. kerbing/edge block to hard standing/footh including necessary earth work. 02/SR/61SA/BLDG - 7.5 Cum

S&F in repairs 15 mm bore CP Bib taps, cast copper alloy with crutch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule fancy type. 02/SR/61SA/BLDG - 2 Each 46/SR BLDG/61SA - 2 Each

S&F in repair 15 mm bore CP Pillar taps fancy type, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe. 02/SR/61SA/BLDG - 8 Each

S&F in repair Stop valves 15 mm bore, . copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions. 02/SR/61SA/BLDG - 4 Each 13/SR/61SA/BLDG - 2 Each

S&F in repair 20 mm bore Stop valves, . copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions. 02/SR/61SA/BLDG - 2 Each 13/SR/61SA/BLDG - 2 Each

S&F in repairs 25 mm bore Stop valve, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions 02/SR/61SA/BLDG - 2 Each

S&F 15 mm bore Stop valves, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends fancy type chromium plated with long shank and cup (concealed type) 04/REV/61SA - 8 Each

S&F 20mm bore Ball brass valves, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule and fixed in repair. 02/SR/61SA/BLDG - 2 Each 13/SR/61SA/BLDG - 2 Each 04/REV/61SA - 2 Each

S&F in repairs Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste chain & plug & porcelain stopper but including brackets, including cutting for and pinning in ends of brackets, erecting stand complete & Waste fittings 32mm bore, brass, CP. 02/SR/61SA/BLDG - 4 Each 46/SR BLDG/61SA - 2 Each

S&F PVC connection 15mm bore with 2 Nos PTMT nuts, 45cm long fixed with one end to pillar tap & the other end to stop cock or iron pipe all as directed by Engineer-in-charge. Make - PRAYAG/SIMET. 02/SR/61SA/BLDG - 30 Each 04/REV/61SA - 8 Each

S&F Cast iron 75mm bore Sand cast soil, waste & vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors, incl Dismantling old pipe 02/SR/61SA/BLDG - 2 Rm.

S&F Cast iron 100 mm bore Sand cast soil, waste & vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors, incl Dismantling old pipe 02/SR/61SA/BLDG - 2.5 Rm

S&F Cast iron 75 mm bore Sand cast soil, waste & vent pipes, in any length with or without ears with cement joints, fixed to walls, incl Dismantling old pipe. 02/SR/61SA/BLDG - 2.5 Rm

S&F Cast iron 100 mm bore Sand cast soil, waste & vent pipes, in any length with or without ears with cement joints, fixed to walls, incl Dismantling old pipe. 02/SR/61SA/BLDG - 2.5 RM

S&F Cast iron 75 mm bore Bends (any radius),diminishing pieces or tapers (larger bore meassured ) 02/SR/61SA/BLDG - 2 Each

S&F Cast iron 100 mm bore Bends (any radius),diminishing pieces or tapers (larger bore meassured ) 02/SR/61SA/BLDG - 2 Each

S&F Cast iron 75 mm bore branches pieces single (equal or unequal )ordianry or inverted (spigot or socket type ) or with paralllel branches. 02/SR/61SA/BLDG - 2 Each

S&F Cast iron 100 mm bore branches pieces single (equal or unequal )ordianry or inverted (spigot or socket type ) or with paralllel branches. 02/SR/61SA/BLDG - 2 Each

S&F 100 mm bore Cast iron cowls 02/SR/61SA/BLDG - 2 Each

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors 13/SR/61SA/BLDG - 5 Rm

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors 13/SR/61SA/BLDG - 2 Rm

S&F PVC (SWR) bends any radius 75mm dia 13/SR/61SA/BLDG - 1 Each

S&F PVC (SWR) bends any radius 110mm dia 13/SR/61SA/BLDG - 1 Each

S&F PVC (SWR), junction single, (Single T) equal or unequal 75mm dia 13/SR/61SA/BLDG - 1 Each

S&F PVC (SWR), junction single, (Single T) equal or unequal 110mm dia 13/SR/61SA/BLDG - 1 Each

S&F PVC (SWR) vent cowl 110mm dia 13/SR/61SA/BLDG - 1 Each 46/SR BLDG/61SA - 32 Each

S&F PVC (SWR) vent cowl of 75mm bore. 46/SR BLDG/61SA - 33 Each

M&L Diameter of outlet 75 mm Cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) 02/SR/61SA/BLDG - 2 Each

Dismantling of old U/S grating and M&L of PVC Nahani / floor trap and square in size of 100X100 mm including MS chromium plated grating 125mm dia of weight not less than 50gm for floor trap / Nahani trap.( Make Paryag and equilant ) 13/SR/61SA/BLDG - 5 Each

M&L PVC (SWR) gully trap 125/110 mm, setting & jointing with solvent cement 13/SR/61SA/BLDG - 4 Each

M&L PCC 1:4:8 type D2 (Using 40mm graded crushed stone aggregates) as in bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150mm bore. 02/SR/61SA/BLDG - 30 RM

M&L Reinforced concrete NP2 drain pipe 150mm internal dia laid in trenches on concrete bed and jointed, complete all as specified. (excavation, earth work and concrete bed and haunching shall be measured and paid for separately) 02/SR/61SA/BLDG - 30 RM

S&F in repairs Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern & flush pipe) 02/SR/61SA/BLDG - 2 Each

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe including PVC pipe (excluding flushing cistern, flush pipe and waste pipe) 02/SR/61SA/BLDG - 2 Each 46/SR BLDG/61SA - 2 Each

Demolition of old existing unserviceable EWC seat and S&F vitreous china wash down water closet pan ( Pedestal pattern ),white including connection to drain (or outgoing pipe) and to flushing pipe,anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete. 46/SR BLDG/61SA - 1 Each

S&F in repair PVC valve less syphonic action type low level flushing cistern coloured with inlet ball valve float and handle incl bracket 10 Lit capacity Make:- slimline / Paryware 02/SR/61SA/BLDG - 2 Each

S&F Grating fixed in repair 02/SR/61SA/BLDG - 2 Each

S&F PVC Waste Pipe 32 mm bore for WHB 02/SR/61SA/BLDG - 16 Each

S&F Flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern 02/SR/61SA/BLDG - 15 Each

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concretebut excluding ashlar facings, dressed stonework and precast concrete articles. 02/SR/61SA/BLDG - 3 Cum 13/SR/61SA/BLDG - 4 Cum 46/SR BLDG/61SA - 3 Cum

Demolition of stone setting paving of any discription of any thickness laid ,bedded and pointed in any mortar 02/SR/61SA/BLDG - 3.6 X Sqm

Demolition of PCC in ground floors and pavings not exc 15cm thickness ( below or above ground level ) 02/SR/61SA/BLDG - 17.55 Cum

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for. 13/SR/61SA/BLDG - 8 Cum

Demolition of PCC in roof covering, kerbs, roof kerbs, benching, coved fillets etc including old decayed water proofing treatment of any type all as directed by Engineer-in-charge. 02/SR/61SA/BLDG - 10.83 Cum 13/SR/61SA/BLDG - 1 Cum 46/SR BLDG/61SA - 1 Cum

Demolition of Stone slabs in roofs, suspended floors, chajjas, landings, etc. any thickness, jointed in any mortar 13/SR/61SA/BLDG - 2 sqm

Dismantling of cast iron drain pipe of 100mm bore, jointed in CM and taking out of trenches, if required. Note :- Excavation & earthwork shall be measured and paid separately. 02/SR/61SA/BLDG - 10 Rm

M&L Applying one coat of polymeric primer @ 0.30 Kg per sqm, conforming to IS : 3384. A layer of APP based polymeric membrane, 3 mm thick (min), weighing not less than 3.5 Kg/Sqm, reinforced with polyster non woven fabric ( weighing not less than 150 gms/ Sqm). Application of polymeric membrane shall be by torch application all as per manufacturer instructions and finally applying one coat of bitumen @ 1.20 Kg/ Sqm on APP membrane before application of Aluminium Paint. 02/SR/61SA/BLDG - 353 Sqm 13/SR/61SA/BLDG - 250 Sqm 46/SR BLDG/61SA - 140 Sqm

M&L Applying one coat of alluminium paint on surface of any description wood,steel,iron, concrete,brick , stone etc exc 10 cm in width or girth, application of paint shall be as per manufacturers instructions. 02/SR/61SA/BLDG - 353 Sqm 13/SR/61SA/BLDG - 250 Sqm 46/SR BLDG/61SA - 140 Sqm

M&L Fancy type MS bracket suitable for curtain rod fixed in repair 02/SR/61SA/BLDG - 30 Pair 13/SR/61SA/BLDG - 40 Pair 01/SR/61SA/BLDG - 60 Pair

M&L 20 mm dia Drapery Fancy type curtain rod fixed in repair 02/SR/61SA/BLDG - 50 RM 13/SR/61SA/BLDG - 30 RM 01/SR/61SA/BLDG - 125 RM

M&L Fancy type caps/ side Bulbs PVC powder coated suitable for curtain rod fixed in repair 02/SR/61SA/BLDG - 30 Pair 13/SR/61SA/BLDG - 40 Pair 01/SR/61SA/BLDG - 60 Pair

M&L Precast interlocking tiles with bullnosed edge jumbo popodoro PVC moulded of 60mm thick M 35 grade epoxy coated set, jointed and pointed in dry sand over 25mm thick sand cushion 02/SR/61SA/BLDG - 130 Sqm

M&L Preparation of new plastered surfaces and applying two coats of plastic emulsion paint of approved shade/tint over a coat of Birla wall care putty and primer on walls all as specified & directed by Engineer-in-Charge 13/SR/61SA/BLDG - 30 Sqm

M&L Two coats of plastic emulsion paint on newly plastered surfaces of Ceiling over a coat of Birla putty and primer including preparation of surfaces. 13/SR/61SA/BLDG - 30 Sqm

M&L Preparation of new plastered surfaces and applying two coats of weather based Apex paint of approved shade on walls over a coat of primer all as specified & directed by Engineer-in-Charge 13/SR/61SA/BLDG - 50 Sqm

M&L Complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of plastic emulsion paint of approved shade/tint over a coat of primer on walls including filling the depression and holes by birla putty all as specified & directed by Engineer-in-Charge Make Asian Paints royale emulsion 13/SR/61SA/BLDG - 300 Sqm

M&L Complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of oil bound distemper of approved shade/tint over a coats of birla wall care putty on ceiling all as specified & directed by Engineer-in-Charge 46/SR BLDG/61SA - 50 Sqm

M&L Complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of plastic emulsion paint of approved shade/tint over a coat of primer on ceiling including filling the depression and holes by birla putty all as specified & directed by Engineer-in-Charge Make Asian Paints royale emulsion 13/SR/61SA/BLDG - 200 Sqm

M&L Complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coat of weather based apex paint of approved shade upto two storey building and scaffloding arrangement including filling depressions by birla wall care putty and preparation of surface by primer all as specified and directed by Engineer-in-charge. 13/SR/61SA/BLDG - 400 Sqm 46/SR BLDG/61SA - 400 Sqm

M&L 15 mm bore CP cast copper alloy bib tap two way with wall flange and areator fancy type quarter turn (Make- JAQUAR Queens Collection) fixed in repair. 13/SR/61SA/BLDG - 3 Each

S&F 15mm bore PVC connection with 2 Nos PTMT nuts, 45cm long fixed with one end to pillar tap & the other end to stop cock or iron pipe all as directed by Engineer-in-charge. Make - PRAYAG/SIMET 13/SR/61SA/BLDG - 10 Each

M&L 15mm bore CP fancy Type center hole basin mixer cast copper alloy with 450 mm copper hose /braided hose without Popup waste system quarter turn (Make-JAQUAR Queens collection Cat part No QQT-7167B) 13/SR/61SA/BLDG - 3 Each

M&L CP wall Mixer with flange & 115 mm long bend pipe forover head shower non Telephonictype with connecting legs wall flanges and crutch etc quarter turn ( Make- JAQUAR Queens Collection CAT part No QQT-7267) 15mm bore for mixing hot & cold water fixed in repairs. 13/SR/61SA/BLDG - 3 Each

M&L Towel ring of brass CP Squar flange (Make-JAQUAR queens collection) and fixed in repairs 13/SR/61SA/BLDG - 3 Each

M&L 15 mm bore Chromium plated Overhead Rain shower with relvoling joint and 115mm long shower arm with wall flange fancy type any colour (Make-JAQUAR queens collection cat part No OHS-CHR-1639) and fixed in repair 13/SR/61SA/BLDG - 3 Each

M&L 15 mm bore Chromium plated angle stop cock with wall flange fancy type cast copper alloy any colour (Make-JAQUAR Queens Collection Cat part No QQT-7053) fixed in repair 13/SR/61SA/BLDG - 10 Each

S&F in repairs counter Vitreous China wash hand basin flat back basin white / , coloured, , size 600x385x195 mm including CP waste coupling but excluding taps, waste chain & plug & ( Make-Jaquar VGS-WHT-81931N ), fixed in repair 13/SR/61SA/BLDG - 2 Each

S&F CP bottle trap of best quality of make Jaquar or equivalent all as specified and directed. 13/SR/61SA/BLDG - 2 Each

Demolition of old existing unserviceable EWC seat and S&F vitreous china wash down water closet pan wall mounted white including connection to drain (or outgoing pipe) and to flushing pipe,anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete including Cisteren .( Make- Jaquar queens Collection Cat Part No QNS-WHT-7851S300UF) fixed in repair 13/SR/61SA/BLDG - 3 Each

S&F Waste fittings 32mm bore, brass, CP for glazed ware sinks, basins, etc. with long screwed shanks & fly-nuts, flange end bedded in red lead cement & other end fixed(Make-MARC CAT PART NO MAC 3020 or equivalentof CERA JAQUAR) fixed in repair 13/SR/61SA/BLDG - 2 Each

S&F CP health faucet fancy type complete with hand lever and long CP chain all as specified and directed by Engineer-in-charge Make Jaquar 13/SR/61SA/BLDG - 4 Each

Dismantling and taking up or down the existing unserviceable GI pipe and M&L for new CPVC pipes with all fittings and fixed complete in walls and ceilings or laid in floors including cutting/chases of walls and making good to damage surface of walls of following sizes :-

15 mm bore 13/SR/61SA/BLDG - 10 RM

20 mm bore 13/SR/61SA/BLDG - 5 RM

S&F 500 ltr PVC water storage tank of capacity triple layered including disconnecting of existing tanks all as specified 13/SR/61SA/BLDG - 2 Each

M&L Providing circular, raised platform of height 20 cm below the tank and base 15cm more than the external dia of thank of PVC cylindrical water tank of capacity 500/1000 liters using PCC 1:3:6 type C1 using 20mm graded stone aggregate with smooth finish 13/SR/61SA/BLDG - 2 JOB 04/REV/61SA - 2 JOB

S&F in repairs elegent mirror PVC cabinet with towel rail of size 475 x 600 x 150 mm all as specified (Make : Paryag/ Commander) 13/SR/61SA/BLDG - 4 Each

S&F Soap dish brass CP ((Make-CERA CAT PART NO CA 103 or equivalent of MARC, JAQUAR) fixed in repair 13/SR/61SA/BLDG - 4 Each 04/REV/61SA - 4 Each

S&F Toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws(Make-Jaquar CAT PART NO CAN-1153S) fixed in repair 13/SR/61SA/BLDG - 2 Each

S&F Bathroom Glass corner of best quality (as per sample) 13/SR/61SA/BLDG - 8 Each 04/REV/61SA - 8 Each

S&F Bathroom Glass Shelf fancy type of best quality (as per sample) 13/SR/61SA/BLDG - 4 Each

M&L 19 mm thick coloured kitchen cabinet door shutter made out by MDF boards pre laminated both side with PVC coated lipping work on edge of shutter including fixed in repair 13/SR/61SA/BLDG - 5 Sqm

M&L 19 mm thick kitchen cabinet partition and shelf etc made out by MDF boards pre laminated both side including fixed in repair . And including support/ bearing member of shelf in cabnaite 13/SR/61SA/BLDG - 5 Sqm

S&F Auto close hinges, stainless steel, bright finish or electrogalvanised fixed in repair 13/SR/61SA/BLDG - 10 Each 46/SR BLDG/61SA - 60 Each

S&F Brass handle of 100mm size cast type, polished bright 13/SR/61SA/BLDG - 10 Each 46/SR BLDG/61SA - 30 Each

S&F 150mm long Brass barrel tower bolts of extruded section. 13/SR/61SA/BLDG - 6 Each

S&F 300 mm long Brass sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded sections or cast aluminium alloy. 13/SR/61SA/BLDG - 2 Each

S&F Brass floor door stopper overall length of cover plate140 mm double legged with rubber shoe, fixed to bottom rail of door as directed. 13/SR/61SA/BLDG - 2 Each

M&L Grinding and polishing of marble and kota stone with machine and evenly applying polish on the surface all as specified and directed. 13/SR/61SA/BLDG - 300 Sqm

S&F Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-410W Gde E-250 quality 'A' all as specified and directed by EIC. welding etc and fixing in position complete of Gde Fe-410W Gde E-250 quality 'A' 13/SR/61SA/BLDG - 300 Kg

M&L Suspended false ceiling using mineral fibre board of size 600 x 600 x 15mm as ceiling over and including suspension metal(galvanised iron) system ) designer grid (15mm grid 8mm return) bevelled tegular suprafine XL 15mm / silhouete complete including necessary hanging system arrangement 6 mm dia suspenders as per manufacture's instruction which is required to be made from existing RCC roof/stone slab of building complete all as specified and directed by Engineer-in-Charge Make :- Armstrong(ANF RH 90) or equivalent make of Everest , Gypsum India Ltd, Bison and Aerolite. 13/SR/61SA/BLDG - 42 Sqm 46/SR BLDG/61SA - 250 Sqm

M&L PVC vinyl flooring in size 0.60x0.60 m in floors including preparation of surface all as specifed and directed. 13/SR/61SA/BLDG - 20 Sqm

M&L French polishing on surfaces of any description, width or girth including cleaning and preparing the surface. 13/SR/61SA/BLDG - 100 Sqm

M&L CP cast copper alloy bib taps two way with wall flange and areator fancy type of 15 mm bore quarter turn (Make-CERA CAT PART NO CQ 606or equivalent of MARC, JAQUAR) fixed in repair. 04/REV/61SA - 4 Each

S&F in repairs elegent mirror PVC cabinet with towel rail of size 475 x 600 x 150 mm all as specified (Make : Paryag/ Commander) 04/REV/61SA - 4 Each

S&F Tooth brush holder/ Tumbler brass CP for putting bathroom utilities ((Make-CERA CAT PART NO CA 104or equivalent of MARC, JAQUAR) fixed in repair 04/REV/61SA - 4 Each

S&F 15 mm bore Brass CP Angle stop cock fancy type concealled type long body 04/REV/61SA - 12 Each

M&L CP fancy Type center hole basin mixer 15mm bore cast copper alloy with 450 mm copper hose /braided hose without Popup waste system quarter turn (Make-CERA CAT PART NO CQ 615 or equivalent of MARC, JAQUAR) 04/REV/61SA - 2 Each

M&L CP wall Mixer with flange & 115 mm long bend pipe forover head shower non Telephonictype with connecting legs wall flanges and crutch etc quarter turn ( Make-CERA CAT PART NO CQ 612 or equivalent of MARC, JAQUAR) 15mm bore for mixing hot & cold w 04/REV/61SA - 2 Each

M&L Towel ring of brass CP Squar flange (Make-CERA CAT PART NO CQ 102 or equivalent of MARC, JAQUAR) and fixed in repairs 04/REV/61SA - 4 Each

M&L Chromium plated Overhead Rain shower with relvoling joint and 115mmlong shower arm with wall flange 15 mm bore fancy type any colour (Make-CERA CAT PART NO CP 140 or equivalent of MARC, JAQUAR) and fixed in repair 04/REV/61SA - 2 Each

M&L CP cast copper alloy bib taps Long body with wall flange fancy type of 15 mm bore quarter turn (Make-CERA CAT PART NO CQ 604 or equivalent of MARC, JAQUAR) fixed in repair. 04/REV/61SA - 4 Each

S&F in repairs Vitreous China wash hand basin flat back basin including half pedastal CERA Part No 1071 CYRCSS white / , coloured, , size 610x560mm including CP waste coupling but excluding taps, waste chain & plug & ( Make-Make-CERA CAT PART NO1071 or equivalent of , HINDWARE/ PARRY WARE ), fixed in repair 04/REV/61SA - 2 Each

Demolition of old existing unserviceable EWC seat and S&F vitreous china wash down water closet pan ( Pedestal pattern ),white including connection to drain (or outgoing pipe) and to flushing pipe,anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete Make-EWC HINDWARE CAT PART NO 20053 TULIF or equivalent& CISTEREN HINDWARE CAT PART NO 21036 or equilant ) fixed in repair 04/REV/61SA - 2 Each

M&L Complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of old decorated plastered/ unplastered Surfaces of edges, facia & projection etc and applying two coat of OBD including all arrangement all as specified and directed by Engineer-in-charge. 46/SR BLDG/61SA - 200 Sqm 04/REV/61SA - 100 Sqm

E/M Portion Taking down carefully copper/ aluminum point wiring (light, fan, socket or power) complete including all fittings such as switches, ceiling roses, pendants, sockets, lamp holder, brackets light fittings tube light fitting, bell/ buzzer ,regulator etc (excluding fans) and making good disturbed surfaces of wall floors, ceiling etc complete all as specified and as directed by Engr-in-Charge to match with existing surface. 02/SR/61SA/BLDG - 138 Point 13/SR/61SA/BLDG - 195 Point 46/SR BLDG/61SA - 148 Point

M&L Point wiring using approved colour coding as per IS, with stranded copper conductor 1.5 Sq. mm (nominal area), single core, FRLS insulated, PVC insulated and unsheathed stranded cable 1100 volts grade, confirming to IS-694/ISI marked in and including PVC concealed conduit including conduit accessories, medium grade, ISI marked, with mild steel sunken boxes with earth dolly zink coated and including mounting frame and over cover plate, including PVC insulated stranded copper conductor 1.5 Sqmm (nominal area) single core cable as earth continuity conductor to common earth and connected FRLS cable 1100 V grade as continuous earth wire to earth dolly for followings. Make:- Finolex/Havells/Polycab

(a) One light/fan/ bell point controlled by one, one way switch. 13/SR/61SA/BLDG - 100 Point 02/SR/61SA/BLDG - 63 Point 46/SR/61SA/BLDG - 54 Point

(b) One light point controlled by two, two way switches. 13/SR/61SA/BLDG - 4 Point 46/SR BLDG/61SA - 2 Point

(c) One 3 pin 5 Amp socket outlet on independent board with other switches. 13/SR/61SA/BLDG - 34 Point 46/SR BLDG/61SA - 42 Point 02/SR/61SA/BLDG - 32 Point

(d) One 3 pin 5 Amp socket out let on the same board with other switches 02/SR/61SA/BLDG - 15 Point 13/SR/61SA/BLDG - 25 Point 46/SR BLDG/61SA - 24 Point

All as per Item No. 232 above but with 2.5 Sqmm copper cable for 3 pin 15 Amps socket outlet on independent board, including 2.5 Sqmm copper cable continuous earth wire and connecting to common earth dolly. 02/SR/61SA/BLDG - 26 Point 13/SR/61SA/BLDG - 22 Point 46/SR BLDG/61SA - 22 Point

All as per Item No. 232 above but with 4 Sqmm copper cable for 3 pin 15 Amps socket outlet on independent board, including 4.0 Sqmm copper cable continuous earth wire and connecting to common earth dolly. 02/SR/61SA/BLDG - 2 Point 13/SR/61SA/BLDG - 10 Point 46/SR BLDG/61SA - 4 Point

S&F switch, piano type 230/250 volts (Make ; Anchor or equivelent model in kinjal/bajaj/Phillips)

(a) Single pole, one way 5 Amp rating 46/SR BLDG/61SA - 120 Each

(b) Single pole, one way 15 Amp rating 46/SR BLDG/61SA - 26 Each

S&F Socket, piano type 230/250 volts :- make: Anchor/kinjal/bajaj

(a) Socket 15 Amp rating 46/SR BLDG/61SA - 26 Each

(b) Socket 05 Amp rating Make- Anchor Cat pt No-14304 46/SR BLDG/61SA - 66 Each

S&F fan speed regulator, electronic step type, suitable for single phase AC, 240 volts, 50 Hz, 100 watts mini rotary type all as specified and as directed. 46/SR BLDG/61SA - 12 Each

S&F only Switch, modular type, 230/ 250V grade on top covers (catered in point wiring) :-

(a) Single pole, one way 6 Amp rating. 02/SR/61SA/BLDG - 106 Each 13/SR/61SA/BLDG - 139 Each

(b) Single pole, one way 16 Amp rating. 02/SR/61SA/BLDG - 26 Each 13/SR/61SA/BLDG - 22 Each

(c) Single pole, two way 6 Amp rating. 13/SR/61SA/BLDG - 8 Each

(d) Bell push flush type, 6 Amp 02/SR/61SA/BLDG - 4 Each 13/SR/61SA/BLDG - 20 Each

S&F Socket outlet multipurpose use, Modular type non/shuttering non/ interlocking flush mounting type, 230/250 Volts grade on top covers (catered in point wiring above) :-

(a) 5 Pin 6 Amp (with 2 pin out let of 5 Amp also). 02/SR/61SA/BLDG - 47 Each 13/SR/61SA/BLDG - 59 Each

(b) 6 Pin 16 Amp (with 3 pin out let of 5 Amp also). 02/SR/61SA/BLDG - 26 Each 13/SR/61SA/BLDG - 22 Each

S&F Speed regulator modular type for ceiling fan electronic type 230 Volts complete. Make Anchor Cat Pt No- 22546 or equivelent model in Havells/Bajaj / CG 02/SR/61SA/BLDG - 29 Each 13/SR/61SA/BLDG - 15 Each

S&F Electric bell multi music type AC 230 volts single pole for AC 230V, 50 Hz .ding dong type(ISI marked) 02/SR/61SA/BLDG - 4 Each 13/SR/61SA/BLDG - 8 Each

M&L Ceiling rose surface bakelite 65x50mm, three terminals ,(ISI marked). 02/SR/61SA/BLDG - 73 Each 13/SR/61SA/BLDG - 30 Each 46/SR BLDG/61SA - 42 Each

S&F Lamp holder insulated body with back plate for batten fitting. Make Anchor/bajaj/philips. 02/SR/61SA/BLDG - 8 Each 13/SR/61SA/BLDG - 10 Each 46/SR BLDG/61SA - 8 Each

S&F T5 integrted batten LED Light fittings 1 x 20 W ,240 volt( size-4 feet/1136 mm) long life, surface/wall mounting IP 20, luminaire per watt (Minium) extruded alluminium housing with frosted PMMA diffuser with high brightness LEDs complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size. Make - C&S Cat No LTTB4F20WLED/ Wor equivelent model in Bajaj/Wipro/ Philips/CG /Surya roshni 13/SR/61SA/BLDG - 40 Each

S&F BATTEN, LED Light fittings multi colour (3 in 1, White, warmwhite and coolwarwhite) 1 x 20 W ,240 volt( size-4 feet/1136 mm) long life, surface/wall mounting IP 20, luminaire per watt (Minium) extruded alluminium housing with frosted PMMA diffuser with high brightness LEDs complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size. Make - Siska CAT part No SSK-SQ-2201-22W-3IN-1 or equivelent model in Wipro/ Philips/CG 13/SR/61SA/BLDG - 12 Each

S&F Surface mounted LED Mirror light fitting 6 W LED Warmwhite waterproof curve, antique design with fine finishing provide with high power LED, energy saving ,lower power consumption, no RF interference, environmental friendly and recyclable, easy for installation water proof LED Driver suitable for bathroom, bedroom pre-wired twin core twisted flexible copper conductor cable with suitable size as per sample and as directed by engineer in charge 13/SR/61SA/BLDG - 10 Each

S&F BATTEN, LED Light fittings 1 x 20 W ,240 volt( size-4 feet/1136 mm) long life, surface/wall mounting IP 20, luminaire per watt (Minium) extruded alluminium housing with frosted PMMA diffuser with high brightness LEDs complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size. Make - Siska CAT part No SSK-T5-22W or equivelent model in Bajaj/Wipro/ Philips/CG /Surya roshni 46/SR BLDG/61SA - 30 Each 02/SR/61SA/BLDG - 44 Each

S&F Wall Bracket light asthetically designed with B22d & E27 lamp holder including 10W LED Lamp with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size. Make - Halonix cat Pt No- HLBW-01-B22 or equivelent model in Bajaj/ Philips/Syska 13/SR/61SA/BLDG - 16 Each

S&F Security lights LED 45 W Energy saving & Environmental friendly long life versatile pressure die cast aluminium with toughened glass cover with high power LED including option of secondary optic with IP 65 protection with and including bracket made out of suitable size of GI medium grade tubing 2 metre long and bent to shape at 120 degree angle at the middle from vertical, fixed with clamps nuts and bolts, washer complete all as specified . Make- CG cat Pt No-LSTS-45-CDL-M or equivalant in HAVELLS ,Syska ,Phillips,Shakti fixture,C &S 02/SR/61SA/BLDG - 3 Each 13/SR/61SA/BLDG - 5 Each 46/SR/61SA/BLDG - 4 Each

S&F LED Energy saving 60 W fitting IP 65 flood light luminaire with pressure die cast aluminium housing 60 W LED fitting complete all as specified & directed by Engr-in-Charge Make- CG Cat Pt No-LSFO-60-CDL or equivalant in Phillips ,HAVELLS, SYSKA, Bajaj and Wipro 02/SR/61SA/BLDG - 2 Each

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.3 mm burried directly in ground (earth pit not less than 2.25 meters deep below normal ground level ), with top edge of the plate not less than 1.5 mtrs below normal ground level , connected to and including galvanised earth strip 25X 4 mm by means of galvanised iron bolts , nut and washers and connected to other end to main panel board duly protected by galvanised iron pipe 25 mm dia " light grage " earth plate surrounded by packed layer of coat dust and common salt 15 cm thick all around bottom and top watering pipe 20 mm bore of galvanised iron " medium grade " with funnel all as shown on electrical plate No 5 of SSR part -I and connecting to earthing testing on completion including cast iron cover frame and PCC 1:3:6 type C-2 using 20 mm grade stone aggregate as in earthing pit with cast iron cover and frame including necessary earth work etc complete all as per specified and directed by Engr-in-Charge . 02/SR/61SA/BLDG - 2 Each Set 46/SR BLDG/61SA - 1 Each Set

Earthing with steel earth plate electrode of size 60cmX60cmX6.3mm thick buired directly in ground to a depth not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr deep below normal ground level connected to galvanized iron wire of size 4 mm dia as earthing lead by means of nuts, bolts and washers of stel, 20 mm dia GI watering pipe with funnel and wire mesh, PCC pit 1:3:6 with pit cover size 30X30cm made of RCC 1:3:6 with suitable handle, angle iron frame made of angle iron of size 40X40X4mm, adequate qty of charcoal dust and salt layers all around the earh plate, removal of surplus soil and returning filling in all as required at site including test point made out of steel plate of size 75X75X6mm fixed to wall all as specified in plate No 3 of SSR Part -I and directed by Engr-In-Charge. 13/SR/61SA/BLDG - 2 Each Set

M & L Cutting round hole of 300 mm in exiting stone wall with suitable drilling eqiupment making good the disturbed surface,plastering the surface with cement motar 1:6 complete and maching the disturbed surface with the existing surface compelete all as specified and directed by engineer in charge. 02/SR/61SA/BLDG - 2 Each Job

S&F Louver made of galavnised iron 300 mm including fixing with suitable fastner complete all as specifed and directed 02/SR/61SA/BLDG - 2 Each

S&F Exhaust fan 300 mm sweep Metal body compete all as specifed and directed. Make : Havells Model -Ventilier DB or equivalent in Bajaj/ Crompton/Usha 02/SR/61SA/BLDG - 2 Each 13/SR/61SA/BLDG - 4 Each

S&F wall fans 450 mm sweep complete all aa specified and directed. Make : Havells Model -Platina or equivalent in Bajaj/ Crompton/Usha 13/SR/61SA/BLDG - 4 Each 46/SR BLDG/61SA - 12 Each

M & L Supplying, laying, connecting and testing in trenches, under floors/ roads or on walls Cable XLPE insulated screened PVC bedded galvanized steel strips or wire armored, electric power cables (heavy duty) ISI marked with stranded aluminium conductor, 1100 volts grade, of size 25 sqmm, 4 core . 46/SR BLDG/61SA - 140 RM

M&L Supplying, laying, connecting and testing in trenches, under floors/ roads or on walls Cable XLPE insulated screened PVC bedded galvanized steel strips or wire armored, electric power cables (heavy duty) ISI marked with stranded aluminium conductor, 1100 volts grade, of size 10 sqmm, 2 core . 02/SR/61SA/BLDG - 130 RM

Excavation in trenches n.exc 1.5 metre wide and n.exc 1.5 metre in depth for foundation etc or for shafts, wells, cess pits, manholes, pier holes, laying cables errection of poles / struts/stays etc n.exe 10 Sqm on plan not exceeding 1.5 metre in depth and getting out in any type of soil. 02/SR/61SA/BLDG - 28.00 Cum 46/SR BLDG/61SA - 39.00 Cum

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm in any type of soil. 02/SR/61SA/BLDG - 18.00 Cum 46/SR BLDG/61SA - 25.00 Cum

M & L Sand cushioning to PVC under ground cable with screened and washed sand and punning to provide a required cover. 02/SR/61SA/BLDG - 8 Cum 46/SR BLDG/61SA - 12 Cum

Removing of excavated material (soil) to a distance n.exc 50 metre and depositing where directed at a level n.exc 1.50metre above the starting point. 02/SR/61SA/BLDG - 10 Cum 46/SR BLDG/61SA - 14 Cum

M&L bricks for protection cover to under ground cable (with old size sub class `B` bricks) with width equal to length of brick laid dry and flat abutting each other with gaps between adjacent brick not exceeding 10 mm as directed by Engineer in-charge. 02/SR/61SA/BLDG - 0.9 Per 1000 Nos 46/SR BLDG/61SA - 1.3 Per 1000 Nos

S&F MCCB 100 amp 10 KA compete all as specified and directed 46/SR BLDG/61SA - 1 Each

S&F RCBOs for earth leackage , overload & short circuit protection 2 pole 100 MA leackage currunt and 32 Amp capacity complete all as specified and directed. 02/SR/61SA/BLDG - 2 Each 46/SR BLDG/61SA - 1 Each

S&F RCBOs for earth leackage , overload & short circuit protection 4 pole 300 MA leackage currunt and 63 Amp capacity complete all as specified and directed. 02/SR/61SA/BLDG - 1 Each 46/SR BLDG/61SA - 1 Each

S & F in repair MCB single pole neutral (SPN) 40-63 Amps for inductive loadconnected through cable lugs of suitable size complete all as directed. 13/SR/61SA/BLDG - 6 Each

S&F sheet metal enclosure complete with metallic plug and socket heavy duty moduler type 3 pin (2P + Earth), 25 amp rating single phase 240 volts complete with MCB SP 25 amp “C” series (Make :Havells/HPL/Anchor/havells(std) 13/SR/61SA/BLDG - 12 Each 46/SR BLDG/61SA - 2 Each

S & F in repair sheet metal enclosure MCB DB 8 way SPN double door suitable for 240 V with 200 amps rated copper bus bar fixed/ flused on walls including cutting Knitch and making good disturbed surfaces including taking down and packing the old surface. 13/SR/61SA/BLDG - 2 Each

S&F in repair factory made, sheet distribution boards, double door protection class IP-42 double door type suitable for mounting MCB/ MCCB, confirming to IS-13032, IS-8623, BS-5484 with minimum 200 amps, copper bus bar of the under mentioned rating :-

(a) SP&N12 ways 02/SR/61SA/BLDG - 3 Each 46/SR BLDG/61SA - 1 Each 13/SR/61SA/BLDG - 2 Each

(b) TPN 4 Ways 02/SR/61SA/BLDG - 1 Each 13/SR/61SA/BLDG - 1 Each 46/SR BLDG/61SA - 1 Each

S&F in repair MCB 10KA confirming to IS-8828 : 1996, IEC-898 : 1995 returing capacity of the undermentioned type and rating:-

(a) SP 5 to 32 amps 02/SR/61SA/BLDG - 30 Each 46/SR BLDG/61SA - 10 Each 13/SR/61SA/BLDG - 32 Each

(b) TPN 63 Amp 02/SR/61SA/BLDG - 1 Each 13/SR/61SA/BLDG - 2 Each

(c) SPN 32 to 63 amps. 02/SR/61SA/BLDG - 3 Each 46/SR BLDG/61SA - 2 Each

Taking down sub main wiring of luminium/copper with PVC/steel conduit:- 02/SR/61SA/BLDG - 70 RM 46/SR BLDG/61SA - 45 RM 13/SR BLDG/61SA - 140 RM

S&F Sub main wiring complete with 3 runs of 10 Sqmm single core PVC insulated unsheathed cable 1100 V grade with multistranded copper conductor ISI marked drawn throughn and including PVC rigid conduit/casing capping and conduit accessories fixed on surface/wall celing etc including provision of 1 run of 10 Sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity. 13/SR/61SA/BLDG - 40 RM

M&L Sub main wiring with two runs of 6 Sqmm single core FRLS PVC insulated but in unsheathed multi stranded copper conductor cable 1100 volts grade drawn through and including of 25mm dia PVC rigid conduit medium with conduit accessories and fixed to the surface of wall/ceiling as per ISI including 6.0 Sqmm PVC insulated copper conductor earth continuity wire. 02/SR/61SA/BLDG - 70 RM 46/SR BLDG/61SA - 45 RM 13/SR BLDG/61SA - 100 RM

UNIVERSAL INFRAPROJECT PVT LTD

Lakshmi Enterprises

J.J.ENGINEERING

Pioneer Enterprises

M/S JALANDRA CONSTRUCTIONS

S.R.Enterprises

agrawal constructions

KARNI CONSTRUCTION COMPANY

Smita Constructions