PAINTING AND POLISHING TO STEEL / WOODEN FURNITURE UNDER THE AOR OF GE DEOLALI

Amount

Material and labour for preparing of old/new polished wood based furniture articles as per the following steps:- Step 1 Sanding:- The wood components shall be rubbed with sand paper No 120 along the grains to remove any dust/ wax/unwanted stains from the surface, the sanding will be repeated with sand paper between 180-220 grit in order to achieve the smooth surface and the wood will be wiped clean with soft clean cloth complete all as specified and directed by Engr - In - Charge. Steps 2 : Staining : Any cracks or holes shall be filled with wood filler of good quality approved by Engr -In - Charge. After the wood filler has dried completly sanding with a stain of approved shade will be then applied to the prepared surface with the help of a soft malmal cloth or brush along the grain'. two to three coats of staining will be done letting the stain dry completly between each coats and sanding every time very fine grit sand paper ( 220-320) NOTE: Excess stain should be wiped off before drying and getting absorbed in wood. Step 3 Polishing : Wood will be finished with a good quality french polish ( mixture of shellac grains and methylated spirit in ratio 1: 10) two to three coats shall be applied to prepared wood surface letting each coat to dry and absorbed fine sanding can be done if required,Polish shall be applied with a soft cloth/ brush along the grains and not against it to achieve high gloss complete all as specified and directed by GE DVL / Engr - In - Charge. Step 4 Varnishing : Two to three coats Varnish shall be applied to prepared wood surface letting each coat to dry and absorbed fine sanding can be done if required,Varnish shall be applied with a soft cloth/ brush along the grains and not against it to achieve high gloss complete all as specified and directed by GE DVL / Engr - In - Charge. Make : Kohinoor/ wilson/Asian/Burger

Almirah Med 1/2S x 1/2 H DB 4232

Almirah Med w/s DB 3954

Almirah Large W/S DB 4232, DB 4116

Book Case FD 45, FD 237

Bin solid Linen Fd 70

Bed W/Ply top w/o FMN FD FD 246/247

Chair dining FD - 279

Chair Easy FD - 229

chair writing FD-280/250

Chair CB W/O Arms DB 3972

Chair Easy Cushioned FD 358

Display Board 1220x 1220mm TP

Hat stand W/M FD 233

Locker Bed side P DB 4074

Peg Table FD-384/277

Rack Boot FD 12

Sofa Set 5 Seater FD-373/281 , 258

Sofa Set 4 Seater FD-373/281 , 258

Sofa single Chair FD-373

Side Board FD 1112, FD 241, FD 371

Table Writing FD-249/275

Table Writing Medium DB 3987, 3955

Table Dressing Gents W/M FD-23

Table Dressing Ladies W/M DB 3980, FD- 45 (M), FD 378

Table Bed Side FD 248, FD 276

Table dining 4 persons, 1200 mm X 900 mm X 760 mm:FD-273,

Table office clerk DB 4120

Table Office Officer DB 4119

Teapoy FD 382, DB 3675

Table Dining 6 pers DB 10081 / FD -273

Table Dining 8 pers FD -273

Table 900x 900 x 760 mm w/Dvr

Table Centre FD 291, FD 283

Table 3x2 with drawer FD 1008

Table 3x2 with out drawer FD 1007

Sofa Set 5 Seater set of (3+1+1) FD/MAP-II/02w/cushion

Bin solid Linen Multipurpose FD/MAP/06

Chair dining Map FD/MAP-II/05

Chair Dining Map FD/MAP - II/04

Table Dressing Ladies Including Stool FD/E6/MAP-II/07

Table Dressing Gents w/m FD/E6/MAP-II/18

Table dining 4 persons, 1200 mm X 900 mm X 760 mm: FD/MAP-II/03

Table dining 6 persons, 1500 mm X 900 mm FD/MAP-II/03

Material and labour for preparing of old/new polished wood based furniture articles of various messes and Guest Rooms as per the following steps:- Step 1 Sanding:- The wood components shall be rubbed with sand paper No 120 along the grains to remove any dust/ wax/unwanted stains from the surface, the sanding will be repeated with sand paper between 180-220 grit in order to achieve the smooth surface and the wood will be wiped clean with soft clean cloth complete all as specified and directed. Steps 2 : Staining : Any cracks or holes shall be filled with wood filler of good quality. After the wood filler has dried completly sanding with a stain of approved shade will be then applied to the prepared surface with the help of a soft malmal cloth or brush along the grain'. two to three coats of staining will be done letting the stain dry completly between each coats and sanding every time very fine grit sand paper ( 220-320) NOTE: Excess stain should be wiped off before drying and getting absorbed in wood. Step 3 Polishing : Wood will be finished with a apporved make quality milamine polish two or three coats shall be applied to prepared wood surface by spray letting each coat to dry and absorbed fine sanding can be done if required,Polish shall be applied with a spray along the grains and not against it to achieve high gloss complete all as specified and directed by GE DVL / Engr - In - Charge. Polishing to the following wooden furniture items will be also carried out in Officer /Jco/Ors Qtrs and unit lines location Make Asian Paints / Nerolac / Berger

Chair Dining W/Long Back FD 357

Chair Dining cushion FD/MAP - II/04

Chair Easy Cushioned FD 358

Hat stand W/M FD 23, 36,262,233

Peg Table FD-384/277

Sofa Set 5 Seater FD-258, FD 281, FD 373

Sofa single Chair FD-373

Table Dining 6 persDB 10081 / FD -273, FD/MAP-II/03

Table Dining 8 persFD - 273

Table Centre FD 29, 274

Locker Bed side P DB 4074

Almirah Large W/S or 1/2 S x 1/2 H DB 4232, DB 4116

M & L for preparing of furniture items as per following steps : (i) Denting of bent surface wih the help of hammer in best workmanship manner. (Ii) Removing old paint by scubbing with sand paper 150 no throughly (ii) Applying one coat of metal primer make: asian / dulux/ nerolac. (iv) Applying metal putty to even the surface and wait period of 2-3 hours to be given for putty to set and dry completely, Scrub off the excess putty with 150 No sand paper and spraying little amount of water simultaneously. (v) Wipe the surfface with soft dry cloth and apply two coat of enamel paint by means spray painting shade as approved by GE DVL / Engr - In -Charge. Make Asian (Apcolite), Berger (Luxol), Shalimar (Superlac) Note- All fur itms parts are to be completed painted and Polished (if any wooden part), dissembling/assembling of fur item to be done as per requirment.Painting to the following furniture items will be also carried out in Officer /Jco/Ors Qtrs and unit lines locations

Almirah Large Steel w/s & w/k FD 67, FD 1031, FD/E6/MAP/18

Almirah Med Steel w/s & w/k FD 67/ FD 1031, FD 243, FD 1032, FD/E6/MAP/18

Almirah Large steel 1/2 s x1/2 H FD 1033

Chair CB steel with arms FD-75(M)

Chair CB Steel without arms FD-75(M)

Chair CBA spl Hand RestFD 120

Chair Varandah FD No-219, FD 256, FD/MAP-II/06,

Form W/Back FD 78 (M)

Form W/O Back FD 77, FD 1027

Locker Bed side steel FD-1029

Side Rack w/tray steel 3/4 spaces FD 1023

Table 3’x2’ with drawer (steel frame) FD 1007

Table 3' x 2' without drawer (steel FD 1008frame)

Teapoy Varandah FD 255, 383,

Table Office Clerk Steel FD 84(M) & 1004

Table Class room steel FD 45, 75

Table Dining Ors w/zink top FD 165 (M)

Table office officer steel FD 84 (M), FD 1003

Chair School W/Hand Board FD/E6/MAP/05

Table Bed Side steel MAP FDE6/MAP/15 R

Bed Hard W/Ply top MAP FD/E6/MAP/08R

Chair Writing Steel Map FD/E6/MAP/12

Shoe Rack Steel FD/E6/MAP/02R

stool steel FD 81/119

side rack with tray steel FD 1023

Trestle store room FD 43/1043

Rack 6 tier steel FD 1038/1039

Charpoy W/Hard top FD/E6/MAP/II/01

Fmn set Iron for Charpay GI Pipe FD/E6/MAP/II/01

Rifle Rack TD/2K/CWE/15

SOFA SET 4 SEATER FD 373

Removing of old unserviceable cushion cover of sofa set 4 seater and supply and fixing with new tapestry cloth of best quality covered and there after top cover with closely woven fabric as approved by Engr - in - charge and cost of tapestry cloth shall not be less than Rs 160/- Per mtr. (08 Nos of Each Set, Four from seat & four from back). Drg No 373

SOFA SET 4 SEATER- Godrej/TP

Removing of old unserviceable rexin cloth of sofa set 4 seater(2 x pices,size of 2 seater approx- width x 1320,depth x 835, height-730 mm) and supply and fixing with new Rexine cloth of Synthetic rexin/composite rexine/leatherette of Best quality and as per exsting pattern and approved by Engr - in - charge and cost of rexine shall not be less than Rs 400/- Per mtr.( cost includes all other work like stiching and patches filling with good quality of racron filler and other req material solution/staple pins for req work ) Drg No TP,

Removing & supply and fixing new 3" steel leg shall be made of all as specified as per existing pattern and directed by Engr - In - Charge.

Removing & supply and fixing of new black malmal /cora cloth below sofa set all as per existing pattern and directed by Engr - In - Charge.

Chair Varandah, Drg No FD 256,

Removing of old cane from chair varandah steel (bottam and back,handle) and re-canning with new best quality plastic cane 4mm wide, white colour complete all as specified and directed and removing old paint by scubbing with sand paper & Apply two coats of synthetic enamel white painting shade as approved by Engr - In - Charge. Make : Maharastra plastic industries / Indian plastic / National Cane (Kachigm – Daman) & Make paint : Asian, Shalimar

Table Dining ORS W/ZINK TOP,Drg No FD 165 (M)

Removing worm out wooden top of table and S & F with 18/19 mm thick particle board exterior grade top of size 1900 x 635 mm covered with 22 gauge superior quality aluminium sheet (All as shown on drawing and directed).

Almirah Large /Med/locker Steel, Drg No FD 67/1031/1302/1033/1029

Removing of unserviceable lock with keys and providing new MS Lock of size 50 mm, 6 levers with stainless steel keys in duplicate for Almirah large/Medium Steel/Locker Steel all as specified and directed by Engr - in - charge. Make : Godrej/Standard/Aligarh or Equivalet

Removing of unserviceable broken handle and S & F new handle steel chromium plated for Almirah Large/Med Steel/Locker steel all as specified and shown in drawing and directed by Engr -in -Charge.

Table centre W/Glass top

Removing of old unserviceable top of glass table centre and supply & fixing new top of glass 10mm thick (4x2) as approved by Engr-In-Charge complete all as specified and shown in drg.

Removing of old & supply & fixing of new Leg shall be as approved by Engr - In - Charge, complete all as specified and shown in drg

Chair Visitor/Computer/Revolving/High Back -FD /TP

Replacement of old unserviceable castors wheel,Supply and Fixing new castor wheel of diffrent types as per Existing patttern & requirement as approved by Engr-in-charge.

Fixing/tightening/welding and greasing of Chair wherever required and painting with synthetic enamel paint of required shade as approved by Engr-In-Charge.

Removing of old Seat and back and S & F new one (Tapestry and cora cloth of approved quality and shade) seat and back to chair computer. Unit rates includes PVC lipping around & new plastic cover(Panni) against dust/dirt to seat and back after change tapestry work (Note: The rate of tapestrey cloth/rexine shall not be less than Rs 200/- per mtr will be approved by Engr - In - Charge.)

Removing of old unserviceable handle and S & F new Handle of Black integral skin polyurethene Re inforced with MS Insert. It shall be scratch and whether Resistance handle of as per exsting pattern and directed by Engineer - in - Charge

Removing of old unserviceable Hydrulic /Gas Pump Mechanism & supply and fixing new one with PVC Cup around fixing between prong and MS tilting frame,It shall consist of drop and provide lift mechanisim and shall be adjusted in the range of 65 mm and can be locked in 5 steps for better lumber support.

Removing of complete old unserviceable MS Tilting Frame/Mechanism fitted to seat and back & supply and fixing new one as per existing pattern or as directed by Eng-In-charge (Including lever for up/down and Bush cup)

Removing of old unserviceable and S & F new Nylon 'A' 10.5 mm dia forged bright zinc plated MS Castor pin is a press fitted in to each prong for holding the castors. It is 600 mm pitch centre dia.

CHARPOY IP FOLDING

Removing of unserviceable ply from charpoy IP folding , tightening the loose frame and S & F new 12 mm thick plywood BWR grade with required size nuts & bolts. complete paiting of all charpay by approved colour. all as specified and as per existing pattern & directed by Engr - In - Charge Refer Drg No. FD - 220 Make-Hindo/ century/Sainik/anchor

Sofa set 4 seater fully upholstered TP

Removing of old unserviceable rexin cloth of sofa set 4 seater (2 x pices,size of 2 seater approx size- width x 1320,depth x 835, height-730 mm and supply and fixing with new Rexine cloth/tapestry of Synthetic rexin/composite rexine/leatherette of good quality and all as per exsting pattern and approved by Engr - in - charge and cost of rexine shall not be less than Rs 400/- Per mtr. (cost includes all other work like stiching and patches filling with good quality of racron filler and other req material solution/staple pins for req work ) Drg No TP.

Removing & supply and fixing new 3" steel leg shall be made of all as specified as per existing pattern and directed by Engr - In - Charge.

Removing & supply and fixing of new black malmal /cora cloth below sofa set all as per existing pattern and directed by Engr - In - Charge.

CHARPOY GI PIPE W/PLY TOP

Removing of old unservicable & Supply and fixing MS Square tube of size 25 mm x 25 mm , 16 Gauge each along width of charpoy, duly welded with frame as support to plywood with hole and fixed with required size nuts & bolts.max no 3 tubes per one charpay .all as specified as per existing pattern and directed by Engr - In - Charge.

Removing of unserviceable plywood and Supply and fixing new 12 mm ply BWR Grade 1 commercial to charpoy GI pipe by means req size of nuts and bolts/screws, playwood size all as shown on drg FD 220. Make- Hindo / century/Sainik/anchor ( only Sch make will be approved)

Table Peg W/Glass top

Removing of old unserviceable top of glass table Peg and supply & fixing new top of glass 10mm thick tempred as approved by Engg-In-Charge complete all as specified and shown in drg.

Removing of old & supply & fixing of new curving Leg shall be as approved by Engr - In - Charge, complete all as specified and shown in drg

Display Board 8'x4'/Notice Board FD 99/117

Removing of unserviceable/broken & supply & fixing of Glass pane 5 mm thick in front of frame/shutter shall be as approved by Engr - In - Charge, complete all as specified as per existing pattern and shown in drg

Removing of unserviceable & supply & fixing of Green blaze cloth shall be as approved by Engr - In - Charge, complete all as specified as per existing pattern and shown in drg

Removing of unserviceable & supply & fixing of 12 mm thick soft board / 6 mm thick plywood shall be as approved by Engr - In - Charge, complete all as specified as per existing pattern and shown in drg

Book case Steel FD 1028

Removing of unserviceable/broken & supply & fixing of new Glass pane 3 mm thick in front of frame/shutter shall be as approved by Engr - In - Charge, complete all as specified as per existing pattern and shown in drg

Removing of unserviceable/broken & supply & fixing of new Handle to shutter as approved by Engr - In - Charge, complete all as specified as per existing pattern and shown in drg

Removing of unserviceable/broken & supply & fixing of new lock to shutter as approved by Engr - In - Charge, complete all as specified as per existing pattern and shown in drg

Paiting of MS frame by means of spray painting of approved shade Synthetic enamel paint of approved colour as directed by Engineer-In-charge

Bed Hard/Double Bed BoxType approx 6 x 61/2 feet (Godrej) TP

Fixing / tightening of Bed by means of suitable screws,nails,fevicol and nut bolts as directed by Engr-In-Charge.

Removing of unserviceable & supply & fixing new playwood/MDF of Bed Hard with hinges for folding/opening and handle for lifting, PVC Beading all around as approved by Engr - In - Charge & as per existing pattern & directed by Engr-In-charge.

Removing of unserviceable & supply & fixing PVC Beading as approved by Engr - In - Charge, complete all as specified as per existing pattern and shown in drg

Removing of unserviceable & supply of new mattress 125 mm thick & size approx 6 x 61/2 feet with good quality of tapestry cover as approved by Engr - In - Charge, all as specified and as per existing pattern.Make-Sleepwell/Kurlon/jyoti/pooja

RACK RIFLE FOR 16 RIFLE TD/2K/CWE/15

Removing (iron members) old paint by scubbing with sand paper & Applying two coats of synthetic enamel oil paint black painting shade on all metal parts, as approved & directed by Enger - In - Charge.

Removing of unserviceable parts (Notch/bracket/PCC Block/nut bolts/Anchor plate) from Rifle rack 16 , tightening the entire loose frame and providing the new new parts (Notch/bracket/PCC Block/nut bolts/Anchor plate) and Polishing of Rifle rack all as specified as per existing pattern and shown in drg

Desk 4' Fd FD 107

Removing of unserviceable & supply & fixing of new 18 mm thick PLB Exterior Grade Box with Teak wood beading around as approved by Engr - In - Charge, complete all as specified as per existing pattern and shown in drg

Painting of MS frame by means of spray painting of approved shade Synthetic enamel paint of approved colour as directed by Engineer-In-charge

Computer cum Writing Table( Godrej) TP

Fixing / tightening of loose Table frame by means of suitable screws,nails,fevicol and nut bolts as directed by Engr-In-Charge.

Removing of unserviceable & supply & fixing Table top made out of 18 mm thick MDF with PVC Beading all around, as approved by Engr - In - Charge, complete all as specified as per existing pattern and shown in drg

Removing of unservicable & supply & fixing Telescopic channel with tray as approeved by Engr-In-Charge as per existing pattern

Note: Amount of sch of credit of Rs.21436/-will be deducted from total amount of BOQ.

SARGAM ENTERPRISES (BID ID -3373991)

M/s. SHRI SAINATH ENTERPRISES (BID ID -3382284)

KASTURILAL HARICHAND OHRI AND SONS (BID ID -3382025)

Imprint Digitech (BID ID -3374560)

M/s Rajesh G Ramsinghani (BID ID -3365666)