COMPR REPAIR OF BR AND EM NATURE WORK OF MD ACCN INCL ROOF TRET, PERIODICALS, SHAFT REPAIR, SUNKEN TRET, PLASTER, JOINERY, SUMMER WINTER APPLI, POINT WIRING ETC IN ALL MD ACCN OF VIVEK , JUNGLE , TRIVENI VIHAR AND THIMMAYA ENCLAVE AT MIL STN JAMMU

Note - Rate quoted below all items of this schedule inclusive provision as under making arrangement for establishment of centralized complaint centre in the existing building as under :- (a) Contractor shall be given user id and password for accessing the online complaint portal and contractor shall at his own expense by himself or his representative feed the data in r/o complaints so generated. (b) Manually registered complaints shall be obtained everyday from MES complaint cell and rectification or otherwise shall be intimated to JE in charge of the cell for updation of manual registers. (c ) Provision and maintenance of all tools, plants, equipment and safely gear required for tradesmen under this contract (d) Provision of communication and conveyance (as required) facilities to supervisor and tradesmen. (e) Monitoring and management of complaints report from generation to execution of complaint including pending complaints. (f) Updating status of lodged complaints on a daily basis. (g) Basic inputs to be noted from the complainants will be locality, Building No, Qtr No, Name and Rank of complaint and exact nature of complaint and mobile No/ telephone (j) On lodging the complaint, the Complaint No will be assigned for reference . Also system should indicate an approximate time for repairs. Accordingly a corresponding complaint slip shall be generated by the system with all relevant info. Complaint slip should be printed in triplicate and to be handed over immediately to Supervisor who shall detail appropriate tradesmen for repair with required materials/store. One copy of complaint shall be retained in complaint centre and two copies with tradesmen.

(Day to day online/offline complaint B/R & E/M)

S&F in repair 15 mm bore bib taps long nose/long body, cast copper alloy CP fancy type with capstan head handle screwed down, quater turn, screwed for brass, weight not less than 450 gms ferrule and fixed complete all as specified and directed.

S&F in repair 15mm bore Bib taps CP fancy type, cast copper, quater turn, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F in repair angle cock with wall flange, cast copper alloy, chromium plated fancy type quater turn screwed for 15 mm iron pipe, complete all as specified and as directed.

S&F in repairs 15mm bore pillar taps, cast copper alloy with capstan heads, chromium plated, fancy type screwed down high pressure with or without lettered “HOT” or “COLD” with long screwed shanks and fly nuts complete all as specified and as directed.

S&F in repairs Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connection and fixed in position fixed in repairs complete all as specified.

S&F in repairs CP jet spray with flexible pipe n.less than 90 cm long fixed to EWC suitable for 15mm bore complete all as specified and directed.

S&F in repair brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges. complete all as specified and as directed.

S&F in repair fancy type Toilet paper holder, steel chromium plated approximate size 140X140X50mm complete all as specified and as directed.

S&F in repair chromium plated towel rack 600mm long & 200mm wide with lower hangers,Stainless steel complete all as specified and as directed.

Supply and fixing in repair soap dish steel chromium plated 100 mm size complete all as specified and directed.

S&F in repair chromium plated steel, towel ring, 200mm dia complete all as specified and as directed.

S&F in repair Sheet glass shelf/ corner glass assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S&F in repair Corner Glass Shelf 5.5 mm thick (300x300mm) chromium plated guard and railing(with Bracket) as per directed by Engr-in-charge.

S&F in repair sink waste coupling of chromium plated brass 40/32 mm dia with long screwed shank and fly nuts complete as suitable for wash hand basin complete all as specified and as directed.

S&F in repair wash hand basine waste coupling of chromium plated brass 32 mm dia with long screwed shank and fly nuts complete all as specified and as directed.

S&F for 15mm bore, 450mm long, PVC connections with brass unions internally threaded both ends complete fixed to iron pipe at both ends as fixed in repairs complete all as specified and as directed.

S&F in repair PVC connection 15 mm bore 600 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore complete all as specified and as directed.

S&F in repairs CP Fancy type shower rose 200mm x 200mm square with long CP Nipple of approved quality complete all as specified.

S&F in repairs wash hand basins, vitreous china,of size 550x400mm (flat back, or angle back type) including cutting for and pinning in ends of brackets or erecting stand inclusive of fixing of waste fitting and waste pipe etc complete all as specified.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level,white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/damaged floor/surfaces, fixing in repair, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair Vitreous china ware pedestal type water closet white, with 'P' or 'S' trap including self closing seat cover, closed pattern with flat bottom,complete all as specified and as directed.

S&F in repair WC Orissa pattern white with integral foot rest 580x 440 mm including PVC P-trap, & PCC bedding in 1:2:4 and making good disturbed floor connecting to trap and flush pipe compete all as specified.(Rate of including in taking out and removal of old WC seat unhygienic condition) complete all as specified and as directed.

Supply and fixing in repair sinks made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495X420 mm bowl size 410x330x160mmmm complete with CP waste coupling & PVC waste pipe complete all as specified and directed by Engineer-in-charge.

S&F in repairs sinks with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm all as specified.

S & F in repair Kitchen stainless steel plate rack made out of 1 mm thick sheet and having partions as per sample. The over all size (39"x30"x10") fixed with steel fastners or steel screw complete all as specified and as directed.

Supply and fixing in repair, brass face/Spindle as per sample for CP/Brass Bib tap, Angle/Stop cock, Pillar cock, wall mixer, WHB mixer, concealed stop cock etc for 15 mm bore pipe complete all as specified and as directed by Engineer-in-charge.

As per item No 29 but spindle for long body concealed stop cock complete all as specified and as directed.

S&F in repair stainless steel lock grating plain/hole size 100 mm dia including embeding in tiles with white cement complete all as specified and as directed.

Supply and fixing in repair PVC Waste pipe 32/40mm bore of required length complete all as specified and as directed.

S&F in repair flushing cistern syphon kit for PVC cistern capacity 10 lit. complete all as specified and as directed by Engr-in-Charge.

S&F in repair 15mm bore Bib tap fancy type, standard or PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm 105gms)

Supply and fixing in repair 1000 litre capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position including 20 mm float valve (PVC) and 02 no's GI tank nipple complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair 500 litre capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position including 20 mm float valve (PVC) and 02 no's GI tank nipple complete all as specified and as directed by Engineer-in-Charge.

Material and labour for cleaning of water storage tank 500 litres capacity completely by removing all scale dirt / dust of any description with chlorine complete all as directed at site including taking down and refixing of tank at the same place, any damage will be rectified by the contractor at his own risk and cost all as directed.

Material and labour for cleaning of water storage tank 1000 litres capacity completely by removing all scale dirt / dust of any description with chlorine complete all as directed at site including taking down and refixing of tank at the same place, any damage will be rectified by the contractor at his own risk and cost all as directed.

Supply and fixing in repair Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 15 mm dia of pipe (Minimum weight 15mm-142gms/ 20mm-210gms./ 25mm-455gms/ 40mm- 690 gms)

All as Per Srl Item No- 39 20 mm dia all complete all as specified and as directed.

All as Per Srl Item No- 39 25 mm dia complete all as specified and as directed.

Supply and fixing in repairs PVC over head tank cover / lid of size suitable for capacity of above 500 litres and upto 1000 litres capacity complete all as specified and directed.

Taking up or down steel tubing of 15 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and as directed

All as Per Srl Item No 43 20 mm dia complete all as specified and as directed.

All as Per Srl Item No 43 25 mm dia complete all as specified and as directed.

Supply and fixing tubes 'medium grade' galvanised, 15 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge

All as Per Srl Item No 46 20 mm dia complete all as specified and as directed.

All as Per Srl Item No 43 25 mm dia complete all as specified and as directed.

Supply and fixing for fittings in repair for steel tubing galvanised, 15 mm bore, such as bends, tees, elbows, unions, short pieces,connectors, back nuts, etc complete all as specified and as directed

Supply and fixing for fittings in repiar for steel tubing galvanised, 20 mm bore, such as bends, tees, elbows, unions, short pieces,connectors, back nuts, etc complete all as specified and as directed

Supply and fixing for in repair fittings for steel tubing galvanised, 25 mm bore, such as bends, tees, elbows, unions, short pieces,connectors, back nuts, etc complete all as specified and as directed

Supply and fixing 20 mm nominal outer dia Chlorinated Polyvinyl Chloride (CPVC) pipes SDR 11, having thermal stability for hot & cold water supply, including all necessary fittings like Plain and Brass CPVC SDR 11 fittings on walls/ceiling or laying in floors,including fixing the pipe with clamps. This includes jointing of pipes & fittings with one step CPVC solvent cement, complete as per direction of Engineer in Charge.

S&F in repair CPVC brass elbow 20 mm outer dia all complete all as specified and as directed.

S&F in repair CPVC brass elbow 20 mm outer dia (3/4x1/2) all complete all as specified and as directed.

S&F in repair CPVC brass Tee 20 mm outer dia all complete all as specified and as directed.

S&F in repair CPVC male brass threaded adapter 20 mm dia((MTA/MBTA) complete all as specified and as directed.

S&F in repair CPVC female brass threaded adapter 20 mm dia. ((FTA/FBTA) complete all as specified and as directed.

S & F in repair plastic water closet seat cover, white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F in repairs 20 mm dia Gun metal, globe or gate valve with iron wheel head,screwed both ends for iron pipe complete all as specifed and dicrected.

S&F in repairs 15 mm dia Gun metal, globe or gate valve with iron wheel head,screwed both ends for iron pipe complete all as specifed and dicrected.

S&F in repair extruted Aluminium alloy handles fabricated type anodised 150 mm long complete all as specified and directed.

S&F in repair extruted Aluminium alloy handles fabricated type anodised 125 mm long complete all as specified and directed.

S&F in repair 150 mm long aluminium anodised barrel tower bolt of extruted section complete all as specified and directed.

S&F in repair 200 mm long aluminium anodised barrel tower bolt of extruted section complete all as specified and directed.

S&F in repair 300 mm long dia aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded section & fixing blots & sliding bolts of extruded section complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue 140 mm anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

S &F in repairs mild steel Helical door spring of size 300 mm at site including welding to steel chowkhats, complete all as specified and directed.

S&F in repair 40 mm dia cupboard knobs fixed with nut and washer brass polished bright finished complete all as specified and directed.

S&F in repair 100 mm hasp and staple safety type aluminuium anodised including bolt to hinge plate and fixed with screw complete all as specified and directed.

S&F in repairs Curtain rod of stainless steel 20mm dia and side capes fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified as directed by Engineer-in-Charge

S&F 3mm thick plain sheet glass, ordinary quality glazing with oil putty in suare n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F 3mm thick Figured glass, pin head type glass, ordinary quality glazing with oil putty in suare n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F in repair 18mm thick single layered HDHMR coloured / textured finish board density more than 850 Kg / cum smooth finished fixed in cupboard and jointed together with necessary adhesive complete all as per directions by Engineer-in-Charge, manufacturer’s specification complete all as specified and as directed

Hacking out old broken glass panes(any thickness, size,quality or description) from wooden/steel frames, glazed with putty or fixed with beads complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia or wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

S&F in repair 30mm wide flap (when open) SS Continuous (piano) hinges, bright finish or electro galvanised fixed to Kitchen cuboard complete all as specified and directed.

S&F in repair medium weight, cold rolled with galvanized mild steel hinge pin, anodized, 75mm size.

S&F in repair medium weight, cold rolled with galvanized mild steel hinge pin, anodized, 100mm size

S&F in repair medium weight, cold rolled with galvanized mild steel hinge pin, anodized, 50mm size

Supply & fixing in repairs switch piano, flush type single pole one way 5Amp, 240 volts ISI marked complete all as specified and directed .

Supply & fixing in repairs Socket outlet 2 in 1, 3 pin, 5A complete all as specified and directed .

Supply & fixing in repairs Switch socket outlet combined 5 pin 5 amp flush type , 240 volts ISI marked complete all as specified and directed.

Supply & fixing in repairs Switch socket outlet combined 2 in 1 , 3 pin 5 amp and 15 amp flush type , 240 volts ISI marked complete all as specified and directed.

Supply & fixing in repairs Socket outlet 5 pin, 15 Amp, flush type, 240 Volts, 6 pin flush type complete ISI marked complete all as specified and directed.

Supply & fixing in repairs switch piano, flush type single pole one way 15 Amps, 240 volts ISI marked complete all as specified and directed .

S&F in repairs Modular switch 1 way 6A,1 module , 240 volts ISI marked complete all as specified and directed

S&F in repairs Modular switch 1 way 16A, 1 module , 240 volts ISI marked complete all as specified and directed

S&F in repairs Modular Socket, 6A - 2/3 pin combined 2 module, , 240 volts ISI marked complete all as specified and directed

S&F in repairs Modular Socket 6A/16A - 2/3 pin combined 2 module, , 240 volts ISI marked complete all as specified and directed

S&F in repairs Modular Fan step regulator, 120W 1 module , 240 volts ISI marked complete all as specified and directed

S&F in repairs modular white cover plate with frame 3 module complete all as specified , 240 volts ISI marked complete all as specified and directed

S&F in repairs modular white cover plate with frame 4 module complete all as specified , 240 volts ISI marked complete all as specified and directed

S&F in repairs modular white cover plate with frame 6 module complete all as specified , 240 volts ISI marked complete all as specified and directed

S&F in repairs modular white cover plate with frame 8 module complete all as specified , 240 volts ISI marked complete all as specified and directed

S&F in repairs modular white cover plate with frame 12 module complete all as specified , 240 volts ISI marked complete all as specified and directed

S&F in repairs distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as directed by Engr-in-Charge. Note:- Distribution board and MCBs should be same make.

S&F in repairs 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning.

S&F in repairs 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 40 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply and fixing in repairs SPN 32 Amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.

Supply and fixing in repairs SPN 40 to 63 Amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.

Supply & fix in repairs calling bell ding dong ,AC 230Volts single pole complete all as specified and directed.

Supply & fix in repairs stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. complete all as specified and directed.

S & F in repairs for bell push , flush type single pole , 5Amp, 240 volts all as specified .

S&F in repairs Ceiling Rose 3 terminal surface type Complete all as directed.

M& L in repairs for Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings

M& L in repairs Self ballast LED retrofit Lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K Complete all as directed.

S&F in repairs LED lights fitting 1x 20W, 220V, AC , PVC Batten type, driver, holder and power factor >0.90 , 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. (4' ft long ) complete all as specified and directed.

S&F in repairs LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F in repairs bulk head luminaries IP65 with opal diffuser 10 watt, 230 Volts LED type complete with 10 watt LED Bulb all as directed Engr-in-Charge.

Supply and fixing in repairs plug top 15 Amps complete all as specified and directed.

(Periodical Services)

M&Lfor preparation of old decorated brick/concrete/ un-plastered surfaces of ceiling etc by washing,brooming & rubbing down or steel wire brushing,scraping down smoke soot,moulds,moss,efflorescent salts,trading oil and greasy sopts including removing the nails etc and cracks/holes in surface filling with white putty and sanding ,durface free from dust, loose paint etc and applying one coat of white wash on Ceiling complete all as specified and as directed.

M&L for preparation of old decorated brick/concrete/ un-plastered surfaces of ceiling etc by washing,brooming & rubbing down or steel wire brushing,scraping down smoke soot,moulds,moss,efflorescent salts,trading oil and greasy sopts including removing the nails etc and cracks/holes in surface filling with white putty and sanding ,durface free from dust, loose paint etc and applying two or more coats of white wash on Ceiling. Complete all as specified and as directed.

M&L for preparation of old decorated brick/concrete/ un-plastered surfaces of ceiling etc by washing, brooming & rubbing down or steel wire brushing, scraping down smoke soot,moulds, moss, efflorescent salts, trading oil and greasy sopts including removing the nails etc and cracks/holes in surface filling with white putty and sanding ,durface free from dust, loose paint etc and applying one coat of Oil Bound Distemper on Ceilings complete all as specified and as directed.

M&L for preparation of old surface of wood rubbing down by sand paper washing by water and applying one coat of synthetic enamel paint over wood surface over 10 cm width or girth complete all as specified and as directed.

M&L for preparation of old surfaces of steel over 10cm width or girth incl, rubbing down by sand paper , washing by water and applying one coat of synthetic enamel paint over steel surface over 10cm width or girth complete all as specified and as directed.

M& L for preparation of old plastered surfaces and applying two or more coats of cement base paint (Including all necessary scaffolding lifiting arrangement up to 10 mtr height) complete all as specified and directed.

Material and labour for preparation of old plastered surfaces of wall and applying one coat of oil bound distemper ocomplete all as specified and as directed.

Material and labour for preparation of old plastered surfaces of wall and applying two coats of oil bound distemper ocomplete all as specified and as directed.

Material and labour for complete removal of existing treatment including fascias, cornices etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint and loose plaster to be completely removed by skilled labour and repair of external wall/Chajjas to be done with repair mortar to get even surface including preparation of old surface of wall/ceiling by filling cracks by Berger Bison Putty / crack fill paste of Berger Paints or equivalent make and make good smoothen surface by sand paper and applying Two or more coats of 100% Premium acrylic exterior emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 1mm thick exterior wall care putty complete all as specified and as directed. (Including all necessary scaffolding lifiting arrangement up to 10 mtr height). DULUX Weather shield Max or ULTIMA PROTEX from Asian paint or Weather coat Anti Dustt Kool from Berber Paint . Note :-(a) The work pertaning to periodical services & water proofing shall be executed from authorized applicator through manufacturer of which the material i.e.paint, distemper, cement base paint, putty etc. is proposed to be used by the contractor and approved by GE. (b) The contractor shall upload along with the documents under cover-I, 'Memorandum of Understanding' (MOU) with only one manufacturer mentioned in the contract, failing which the bid shall be liable to be rejected.

Srl Item No 120 Contd/.... Note :- (a) Work shall be done as per 'Memorandum of Understanding' (MOU) between tenderer and manufacturer of paints and their authorized applicator complete all as specified and directed. (b) The contractor shall upload 'Memorandum of Understanding' (MOU) between tenderer and manufacturer of paints and their authorized applicator after conclude of tender and before place of Work Order Documents as mentioned in NIT. (c) The work pertaning to periodical services & water proofing shall be executed from authorized applicator through manufacturer of which the material i.e.paint, distemper, cement base paint, putty etc. is proposed to be used by the contractor and approved by GE.

(Joinery)

Taking down shutters of any description exc 1.00 Sqm and n.exc. 2.00 sqm each and removing from the site complete all as specified and directed.

Taking down chowkats or frames n. exc. 1.5 sq.m each with shutters9 without taking off shutters from the frame) complete all as specified and directed

Taking down Chowkats or frames exc 1.5 sq.m but n.exc 4 sqm each each with shutters (without taking off shutters from the frames) complete all as specified and directed.

S&F Pressed steel frames (factory made) made out of 1.25 mm thick black MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete size of frame 105x60mm incl bottom of each chowkat to be welded with 2 Nos 25x25x3mm thick flat iron projecting 10 cm on either side complete all as specified and directed.

All as per Item No. 126 here in before but size of frame 125X60mm for fixing of two shutters complete all as specified and directed.

M&L cement concrete (1:3:6) type C0 using 12.5mm graded stone aggregate filling in pressed steel chowkats bed block for holdfast and the like complete all as specified and directed.

S&F Factory made solid PVC moulded Door frame of size 50x100mm with wood free EPS and 2mm thick moulded PVC sheet alaround supplying and fixing in wall at site as per manufacturer specification complete.

S&F Factory made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing

S&F 35 mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned complete all as specified and directed.

S&F 35mm thick 2nd class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) complete all as specified and directed.

S&F Flush shutters, 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia or wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

M&L pressed steel frames for cup board chokhat of size 60x40mm with one or more rebates incl necessary fixing lug, hold fasts etc complete all as specified and directed.

S&F Flush shutters, 25 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 100 mm size stainless steel hinges medium weight cold rolled complete all as specified and directed.

S&F 18/19 mm thick blockboard ,grade 2 quality ,interior grade ,commercial type ,fixed with screw to timber frame-workscrew to timber frame work complete all as specified and directed.

M&L 0.9 mm thick Decorative laminates type 1, or surface finish, colour and pattern fixed with approved adhesive complete all as specified and directed .

S&F 100 mm hasp and staple safety type aluminuium anodised including bolt to hinge plate and fixed with screw complete all as specified and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction ofEngineer-in-Charge. (M.S. hold fast/ lugsor SS dash fasteners shall be paid for separately). →Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibbers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with Butt hinges of required size with necessary full body threaded star headed counter sunk screws, all as per direction of Engineer- In- Charge. (Note: Butt hinges and necessary screws shall be paid separately)

S&F 30mm wide flap (when open) SS Continuous (piano) hinges, bright finish or electro galvanised fixed to Kitchen cuboard complete all as specified and directed.

S&F18mm thick single layered HDHMR coloured / textured finish board density more than 850 Kg / cum smooth finished fixed in cupboard and jointed together with necessary adhesive complete all as per directions by Engineer-in-Charge, manufacturer’s specification complete all as specified and as directed

S & F 18 mm thick factory made 100 % solid WPC flush shutter (for cupboard and vanity etc)made from co-extruded three layer rigid foam sheet(single extruded) with 0.8 to 1 mm thick outer layer having density not less than 1400 kg/cum and density of central core not less than 600 kg/cum manufacturer by an ISO 9001/2015 certified company complete all as specified and directed.

S&F modular auto concealed soft closed hinges 35mm, 110 degree size fixed to cupboard complete all as specified and as directed. Make Hettich/Kaff/sleek

S&F magnet catcher 50 mm size for kitchen cupboard shutter complete all as specified and directed.

M&L for preparing surface of new wood and wood based material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparing surface of new steel material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint complete all as specified and directed.

Dismantling wrought iron or mild steel work as in cooler stand, chazza etc.

S&F Mild steel framed works such as grills, framed guard bars, etc and similar work as in cooler stands, chazza stand etc. conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

S&F in repair powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed.

S&F in repair powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

S&F in repair powder coated aluminium three track sliding type glazed window,shutter with 5mm thick plain sheet glass fixed open track section 100x38x1.4 mm having three track (two of 5.50 mm thick glass & one of stainless steel wirecloth of 0.56 mm dia and 1.18 mm aperture ) with members of window shutters of section 38x12mm including aluminium grill 75 mm x 5.50 mm thick pitch diamond shape ,wire gauge and grill shall be fixed with the help of 40 mm aluminium flat and other standard Bombay sliding section incl all necessary fiber wheel rollers suitable handle to facilitate sliding and all necessary jointing cleats glazing clips,rubber packing, Aluminium snap beeding etc complete all as specified and directed .

S&F Extruded Aluminium alloy handles fabricated type anodised 150 mm long complete all as specified and directed.

All as per item No 155 here-in-before but 125 mm long complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolt of extruted section complete all as specified and directed.

S&F 300 mm long dia aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded section & fixing blots & sliding bolts of extruded section complete all as specified and directed.

S&F medium weight, cold rolled with galvanized mild steel hinge pin, 100mm size

S&F floor door stopper of aluminium alloy body and tongue 140 mm anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

S &F mild steel Helical door spring of size 300 mm at site including welding to steel chowkhats, complete all as specified and directed.

S&F 40 mm dia cupboard knobs fixed with nut and washer brass polished bright finished complete all as specified and directed.

(Leakage/Seepage and certain other misc works)

Taking down Cement Plaster of any description on Brick Walls, Concrete Surfaces including Racking out Joints, hacking for Key, scrubbing down with Water, etc. complete removal of debris outside MD land. (Including all necessary scaffolding lifiting arrangement up to 10 mtr height).

M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and directed. (Including all necessary scaffolding lifiting arrangement up to 10 mtr height).

M&L for forming groove of uniform size 15mm wide and 15mm deep in the top of layer of washed stone grit plaster as per approved pattern using wooden battens nailed to the under layer including removal of wooden battens repairs to the edge of panels and finishing the groove complete as per specification and direction of Engr-in-charge

M&L for Rendering 5mm thick on fair faces of concrete surface of ceiling in CM 1:3, surface finished even and smooth surface without using extra cement.

M&L for Rendering 10mm thick on fair faces of brick work or concrete surface in CM 1:6 surface finished even and smooth without using extra cement.

M&L for Rendering on faire face of concrete/bricks surface on wall/ chajjas/cornices etc with in two layer (10+5) mm thick in CM 1:4 finished even and fair including water proofing compound all as specified. (Including all necessary scaffolding lifiting arrangement up to 10 mtr height).

M&L for Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work not exc 15 cm in width or girth; including cutting to edges, all mitres and stopped ends,

M&L for Preparing of New plastered surface of ceiling and applying two coats of distemper oil bound distemper over primer coat, complete all as specified and as directed by Engineer in charge.

M&L for Preparing of New plastered surface of wall and applying 1mm thick wall care putty and applying two coats of distemper oil bound over primer coat, complete all as specified and as directed by Engineer in charge.

Supply only integral water proofing admixture of approved quality.

Material and labour for preparation of newly plastered surface and applying two coat of premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology, Excellent Dirt Pick up resistance of Berger Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based exterior grade primer @ 0.9ltr(undiluted)/10 sq mtrs diluted with water in 1:1ratio and 1mm thick exterior grade wall putty as per manufacture's instruction and all coats incl primer to be applied with fully automatic airlessspray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and directed Make: Berger Paints Weathercoat Long Life Flexo / Nerolac Paints excel Total / Asian Paint Apex Note :-(a) The work pertaning to periodical services & water proofing shall be executed from authorized applicator through manufacturer of which the material i.e.paint, distemper, cement base paint, putty etc. is proposed to be used by the contractor and approved by GE. (b) The contractor shall upload along with the documents under cover-I, 'Memorandum of Understanding' (MOU) with only one manufacturer mentioned in the contract, failing which the bid shall be liable to be rejected.

S&F Rolled sections conforming toFe-410W (GradeE-250) quality 'A' as in main and cross beams, hip and jack rafters; purlins, trusses, stagging, where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates (Beam, tee, angle, channel or flat sections or MS tube pipe) complete all as specified and as directed.

Dismantling AC corrugated, semi corrugated sheets in roof covering including ridge complete all as specified and as directed.

Supply and fixing pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPs as in roof covering fixed with self tapping screws or L-type or J-type or cranked hook bolts complete all as specified and as directed.

Supply and fixing pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPs as in ridge of roof fixed with self tapping screws or L-type or J-type or cranked hook bolts complete all as specified and as directed.

Material and labour for preparing surface of new steel of any description over 10cm width and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Demolition of concrete in ground floor not exceeding 15cm in thickness below or above ground level including floor finish such as tiles of any thickness and any description etc. complete all as specified and as directed by Engineer in Charge.

Demoilition of lean/cinder concrete filled in sunken slab , wire brusing the surface ,cleaning all loose dirt by dusting/watering sunken portion of WC, Toilet etc and applying cement slurry @1.5 kg per Sqm incld dismentaling of tile complte all as specfied and directed

Dismanting floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and directed.

M&L for Exterior grade full body vitrified tiles matt finished 400x400x12mm thick set jointed in neat cement slurry and pointed with grey cement and pigments to match the shade of tile pattern as approved in floors incl 15mm thick screed in CM 1:6 complete all as specified and as directed.

M&L for vitrified tiles any colour 8-9 mm thick (square/rectangular) polished as in floor , area of each tile n. exc 0.36 sqm etc set and jointed and laid with 3-4mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions, pattern, laying etc of tiles and Shade, Colour shall be decided by Engr in Charge complete all as specified.

All as per item No 184 but in vertical surfaces with 3-4mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions complete all as specified

M & L for Non - skid joint free coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. laid with 3-4mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions complete all as specified and as directed by Engr-in-Charge.

All as per item no 186 above but in vertical surfaces including laid with 3-4mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions complete all as specified

M & L for Non - skid joint free coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. laid with 3-4mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions complete all as specified and as directed by Engr-in-Charge.

M&L for coloured glazed ceramic tiles glossy finish of size 450x300x 5-6mm thick in dado’s/skirting etc (1st quality). laid with 3-4mm spacers set and jointed in laid with 3-4mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions to match, pattern, laying etc of tiles and Shade, Colour shall be decided by Engr in Charge complete all as specified.

M&L for 16mm to 20mm granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and incl Screed bed or bedding layer of mortar 20mm thick in CM 1:6 and taking down old complete all as specified and directed.

M&L for 16mm to 20mm marble (of any typeand any colour ) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and incl Screed bed or bedding layer of mortar 20mm thick in CM 1:6 and taking down old complete all as specified and directed.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations etc. complete all as specified and directed.

S&F in repairs Wall mixer non telephonic shower arrangement with connecting legs and wall flanges, cast copper alloy, chromium plated, complete all as specified and as directed.

S&F in repair chromium plated brass Wall Mixer 3-in-1 System with Provision for both Hand Shower & Overhead Shower Complete with 115mm Long Bend Pipe on Upper Side, Connecting Legs & Flanges (without Hand & Overhead Shower) complete all as specified and as directed.

S&F in repair Sink Mixer swan neck with Swinging Spout (Wall Mounted Model) chromium plated brass with Connecting Legs & Wall Flanges complete all as specified and as directed.

S&F in repair CP brass Sink Cock with Swinging Spout (Wall Mounted Model) with Wall Flange complete all as specified and as directed.

S&F in repairs 15mm bore Pillar taps, cast copper alloy fancy type with capstan heads, chromium plated screw down high pressure, screwed for iron pipe all as directed by Engineer in charge.

S&F in repairs CP Central Hole Basin Mixer for Hot & cold water screwed down without Popup Waste System with 450mm Long Braided Hoses complete all as specified and as directed.

S&F in repairs Shower rose 125mm size, brass chromium plated with or without swivel joints any size including fixing to steel pipe of 15mm bore all as directed by Engineer in charge.

M&L for 25 mm thick PCC 1:2:4 type B 0(12.5mm graded crushed stone aggregate) , as in sub base / floor complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C1 using 20mm graded stone aggregate as in floor/plinth protection laid in suitable panels finished even and fair all as spd . 6mm Joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 gde and three part of sand ( all by weight) complete.

M & L for providing 75 mm thick plain cement concrete 1:4:8 mix, type D-2 (Using 40mm graded stone aggregate) as sub-base floor complete

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete

Providing, cement concrete Type B1, 1:2:4 (20mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges

M & L for providing water proofing treatment to sunken floors all as given below :- (a) Making fillet of size 25mm x 25mm at corner of slab and wall with polymer modified cementitious (PMC) mortar consisting of one part of tapecrete P-151, two parts of cement and 6 parts of fine sand by weight. (b) Sealing of joints of pipe with epoxy putty or epoxy mortar (c) Cleaning the concrete surface by brushing & watering and applying a coat of tapecrete P-151 Acrylic Polymer Modified cementitious slurry consisting of one part of Acrylic based polymer modified cementitious flexible compostie coating and two parts of cement by weight. The coating shall be carried out upto 300mm above FFL and shall be allowed to dry for 4-6 hours. (d) Appying a coat of Acrylic based polymer modified cementitious flexible compostie coating brush topping 1.5mm thick consisting of one part of Acrylic based polymer modified cementitious flexible compostie coating, two parts of cement and two parts of silica sand by weight and cured to 2 days. (e) Applying 15mm thick plaster in CM 1:4 mixed with WPC @ 100ml per 50 Kg cement on treated surface. (f) PCC 1:5:10 type E2 in sunken area.

M & L for provision of roof treatment with polymeric water proofing membrane all as given below :- (a) Taking down existing water proofing treatment and cleaning roof surface by washing and rubbing etc. and removing the material retrieved to a distance not exceeding 500 m where directed. (b) M & L for plastering 10mm thick in CM 1:3 using 100% coarse sand on roof surface including water proofing compound as per manufacturer's instructions and as directed by Engr-in-Charge. (c) Applying a coat of bituminous primer conforming to IS : 3384-1986 @ 0.25 Iitres/sqm on prepared surface and allowed to dry. (d) Applying and laying 3mm thick APP membrane having non oven polyester matt at core and covered with high quality polymeric asphaltic protected thermo fusible HMHDPE film on both sides with over laps 10cm and 15 cm at longitudinal and transverse direction respectively and sealed by flame, sealing all overlaps complete including treatment at all junctions and corners. The membrane shall be torched into groove on vertical plane and groove sealed with cement mortar 1:3. (e) M & L for two coats of aluminium paint on membrane surface all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern) , including all fittings, heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories).

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints,complete fixed to walls at any height complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints complete laid in trenches or in floors complete all as specified and directed.

S&F 110 mm borePVC (SWR) pipes single socketed in any length with rubber ring joints complete fixed to walls at any height complete all as specified and directed.

S&F 110 mm borePVC (SWR) pipes single socketed in any length with rubber ring joints , bends ,Tees complete laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) bends 110 mm radius

S&F PVC (SWR) bends 75 mm radius

S&F 110 mm PVC(SWR) Junction single(T) equal /Unequal

S&F 75 mm PVC(SWR) Junction single(T) equal /Unequal

S&F 110mm PVC(SWR) branch piece, single Y equal or unequal

S&F 75mm PVC(SWR) branch piece, single Y equal or unequal

S&F PVC (SWR) vent cowl of radius of 110 mm dia

S&F in repair 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concerete B1 (1:2:4) complete all as specified and directed.

S& F Stack clamps including bolts and nuts walls or roof for 100/75 mm bore pipe complete all as specified and directed.

Removing vegetation on roof /wall etc by taking down/dismentling/ demolation of brick work/ concrete work/ plaster work etc from root and apply chemical on the vegetation for further non growth in future and making good surface with concrete, tile ,roof treatment platers etc complete to make good surface with existing complete all as specified and directed.

Taking down ceiling plaster & cleaning the steel & concrete surface apply anti-corrsion coating to steel surface with Dr Fixit Rubber guard two coats, then apply bonding agent of pidilite (Dr fixit Pedilite URP) & than apply ready repair mortar thickness as required(not more than 50mm) with FOSROC HB-40 complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars,drains etc, but excluding ashlars facings, dressed stone work and precast concrete articles.

M&L Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified & as directed .

All as per item 224 above but except bricks.

M&L for brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall in CM 1:4 complete all as specified & as directed .

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for reinforced cement concrete, type B1, 1:2:4 mix (20mm graded aggregate) as in slabs & Shelves etc.

Formwork to soffits of slabs including supports, overhangings etc, for fair finished surfaces of concrete

Form work to edges of roof slab of thick not exc 20cm wide and as in similar work

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified

M&L for providing and injecting chemical emulsion for post constructional antitermite treatment along the external wall below concrete or masonary apron using chemical emulsion at the rate 2.25litres per metre including drilling and plugging holes etc complete all as specified and directed

M&L for providing Anti termite treatment of soil under existing floors using emulsion at the rate one litres per holes, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 Cement and 2 coarse sand ) match the existing floor

M&L for Drilling Holes of 12mm dia,upto 100mm deep holes in structural members at the intervals of 300 to 500mm in staggered manner or along the crack as directed by theEngr-in-charge in RC structural element including Cleaning of the holes by air blower and Inserting 12mm dia.Teflon nozzles compatible with epoxy injector and having machined external end to receive outlet of grouting gun. Fix it inside the holes by applying thixotropic epoxy putty to ensurec omplete sealing and allow to cure the system for min 08hrs before grouting including removing nozzle projections, excess putty if anyover concrete element grinding, levelling and finishing the external surface, after completion of the work, etc complete. Note:Epoxy putty cost are included. Drilling of hole shall be done by authorized applicator and the work shall be executed in the presence of company representative.

M&L for Grouting Injecting low viscosity high molecular weight thermosett polymer Monopol 250 H by pressure and using pressure epoxy injector with accessories till nozzles refused to accept the grout, Including Mixing material components part a and part b in required quantities as per mfg instruction by weigh batching Filling the grouting gun with monopol 250 H and maintaining desired pressure in the gun, air compressor and at exit (minimum 3 to 4kg/Cm2) by a mechanism to monitor both pressure gauges and controlling the same by release valves and release the grout as per requirement simultaneously to grout the structural element through prefixed nozzles till its refusal.Seal the nozzle with thixotropic epoxy putty after the refusal.Note: leakages through other nozzles or cracks are required to be monitored while grouting and such points to be sealed as and when required without any extra cost.

SCHEDULE-(Summer/Winter appliances)

Labour for repair/servicing of ceiling fan of any capacity complete with strip opening of ceilling fan for repair/cleaning/varnishing and removing of old lubricating substances from bearing/ bush by using Kerosine oil, carrying out fresh lubrication , greasing and to make the ceiling Fan noise free and smooth functioning, including replacement of worn out/unserviceable minor spare parts split pin,fan body bolts,spring washer,fan rod bolt etc and PVC insulated, unsheathed stranded twin twisted copper conductor cable of size 1.5 Sqmm up to 1.0 M long, assembling the repaired ceiling fan and testing to the entire satisfication of engineer in charge and refifixing in its orginal position all as specified and directed. (Replacement of Spares flexible wire etc/rewinding of ceiling fan/shall be measured and paid seperately under respective item for material and labour cost .)

All as per Srl item No. 238 above but for exhaust Fan of any type and any sweep

Rewinding of ceiling fan, of any make/type and size (1200 sweep) with super enamelled copper wire of appropriate gauge as existing to obtain the specified and satisfactory RPM as per manufactures specification, including replacement of all insulation materials, varnishing, heating, drying, assembling of stater/rotor, connection & testing complete.

All as per Srl item No. 240 above but for exhaust fan of any make/type but of size 300 mm sweep.

Labour for remetalling of worn out shaft of fan, cutting,bracing,machining and polishing to make the shaft suitable for fixing of new ball bearing and fixing ball bearing in repair of bushing system in ceiling fan and assembling the same and testing to the engineer satifaction of engineer in charge to ensure smooth and noise free operation (bearing shall be measured and paid seperately )

Supply and fixing in replacement ball bearing of any size and type, suitable for ceiling Fan .

All asper item No. 243 above but for exhaust fan of any type/make and size

Supply & fixing in repair of capacitor 230 Volt AC 50 Hz, conforming to IS-1709 and Rated capacity 2.5 MFD for ceilling fan & exhaust fan.

All as per item No. 245 above but of rated capacity 4.0 MFD for Exhaust Fan.

Supply and connection of PVC insulated, unsheathed multi stranded,three core twisted copper flexible cable of size 1.5 Sqmm as required. .

Supply and fixing in replacement bush of suitable size for ceiling fan/exhaust fan of any type/size as per existing type.

Supply and fixing in replacement of PVC connector 4 way 6 Amps with connection screws, nuts, bolts all as specified and directed.

Supply and fixing in replacement of PVC clamps with fixing screws for holding capacitor of any type and size.

Supply and fixing in replacement of GI/ MS anodized bolts with anodized nuts, spring washers, split pin etc size 50 mm long 10 mm dia half threaded type with split pin hole

S&F in repair MS clamp for down rod of suitable size including gromet / reel type rubber pad with bolts, nuts,split pin and washers suitable for housing ceiling fan.

S&F in repair of ceilling fan down rod 12 mm dia and 30/45 cm long complete with MS Clamp Rubber reel,split pin nut bolts etc.

S&F in replacement Printed circuit board (PCBs) suitable for BLDC ceiling fans of 1200 mm. Make - As per sample .

Supply and fixing in repair of louver shutter made out of MS sheet metal 1.2 mm thick for round base and 0.8 mm thick for flaps, comprising of mounting legs frames made o MS flat strips of size 25mm x 3mm includidng heavy duty rust proof passivated bolts of size 50 mm long 8 mm dia to be fixed on wall at ground/First/Second floor etc complete with using fastener bolt,driling for exhust fan up to 400 mm sweep incl taking down old one.

Cleaning of ceiling fan assembly of any type/size and carrying out two coat of spray painting with first quality synthetic enamelled paint of approved colour all as directed and specified.

S&F in repair PVC Canopy set of two pieces for ceiling fans of any size

S&F in repair Ceiling Fan blade set of three pieces suitable for 1200/1400 mm sweep of White/Brown/Ivory colors all as specified and directed. Make - As per Sample

Taking down and strip opening to geyser of any make and capacity 25 / 35 / 50 ltrs including disconnection of all water pipe connection and taking out water inlet / outlet assembly, removing glass wool, the inner tank, descaling the assembly and tank, detecting the leakage, welding / brazing the defective parts, repacking the glass wool and refixing the same after making it functional including replacement of worn out nuts, bolts, washers etc complete all as specified and as directed.

Material and labour in repair of water inlet and outlet geyser assembly of existing make as required at site with rubber gasket suitable for geyser of 25 / 35 ltrs capacity electric driven water storage heater with provision of housing for thermostat assembly, heating element fixing arrangement nuts, bolts and washers etc complete all as specified and as directed.

Material and labour in repair thermostat, switch for electric water heater storage type of capacity 25 / 50 ltr, 230 Volts of existing make of geyser complete all as specified and as directed.

Material and labour in repair heating element with triangular base / round base, single phase, 230 Volt, capacity 2 KW of existing make complete all as specified and as directed.

Material and labour in repair pressure release valve conforming to relevant IS 15mm bore suitable for fixing with GI pipe / tubing 15mm bore complete all as specified and as directed.

Material and labour in repair of heavy duty PVC connection (For Hot water) nylon threaded 450mm large (18") 15mm bore including brass nuts, rubber washers complete on both ends complete all as specified and as directed.

Material and labour in repair of heavy duty PVC connection (For Cold water) nylon threaded 450mm large (18") 15mm bore including brass nuts, rubber washers complete on both ends complete all as specified and as directed.

Material and labour in repair of indicator lamps round / rectangular type 230 Volt AC suitable for geyser of any capacity including providing electric connections complete all as specified and as directed.

Material and labour in repair water storage inner tank of stainless steel heavy duty confirming to ISI suitable for 25 ltrs capacity geyser, with provision for fixing 15mm dia galvanized air release valve complete all as specified and as directed.

Material and labour in repair Non return Valve 15mm dia,made up of brass complete all as specified and as directed.

SCHEDULE- (Internal electrification)

M&L in repairs for Sub main wiring with proper colour coding , insulated , unsheathed , multistranded ,copper conductor FRLS, cable of 2 run 6 Sqrmm for phase and neutral and one run of 6.0 Sqrmm for earth wire unsheathed , miltistranded , copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length. Note : Wiring shall be done in proper colour coding.

M&L in repairs for Sub main wiring with proper colour coding , insulated , unsheathed , multistranded ,copper conductor FRLS, cable of 2 run 4 Sqrmm for phase and neutral and one run of 4 Sqrmm for earth wire unsheathed , miltistranded , copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length. Note : Wiring shall be done in proper colour coding.

Taking down old unsv copper/aluminium point wiring concealed / batten (light, fan, socket or power) complete, including fixture and fittings such as switches,sockets, ceiling roses,bell push,bell electric,lamp holder,bulk head fitting, pendants, regulators, sockets, light fitting and any type switch board wooden/iron,round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

M&L for point wiring for one light/fan/call bell point controlled by one 5 Amp switch with 1.5 Sqmm two single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into existing concealed PVC rigid/steel conduit and New CI/pressed steel terminal boxes including 3.00mm thick hylam brand ISI marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified. Note : (a) wiring shall be done by using proper colour coding incl making the disturb surface good. (b) Earth wire shall be of green colour (c) On RCC roof/celing PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engr-in-Charge. (Rates are incluusive of Cutting / Chassis where required with suitable PCC works and making goog to disturbed surfaces.

All as per item No 273 here in above but One 5 pin socket outlet 5 amps on the same board

All as per item No 273 here in above but One 5 pin socket outlet, 5amps, independent

All as per Item No 273 here in above but for one 5 pin socket outlet 15 Amps on Independent board with cables 2.5 sqmm size.

Supply & fixing switch piano, flush type single pole one way 5Amp, 240 volts ISI marked complete all as specified and directed .

Supply & fixing Socket outlet 2 in 1, 3 pin, 5A complete all as specified and directed .

Supply & fixing Switch socket outlet combined 2 in 1 , 3 pin 5 amp and 15 amp flush type , 240 volts ISI marked complete all as specified and directed.

Supply & fix calling bell ding dong ,AC 230 Volts single pole complete all as specified and directed.

Supply & fix stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. complete all as specified and directed.

S & F for bell push , flush type single pole , 5Amp, 240 volts all as specified .

S&F Ceiling Rose 3 terminal surface type Complete all as directed.

S&F for Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F Self ballast LED retrofit Lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K Complete all as directed.

M&L for point wiring for one light/fan/call bell point controlled by one 5 Amp switch with 1.5 Sqmm two single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into and including new concealed PVC conduit ISI marked including Modular Metal flush Boxes of any way with Modular white cover plate with frame for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :- Note : (a) wiring shall be done by using proper colour coding including making disturb surface good (b) Earth wire shall be of green colour (c) On RCC roof/celing PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engr-in-Charge. (d) Rates are inclusive of cutting / chassis with suitable PCC works and making good to disturbed surfaces of Walls / Floor.

All as per item No 286 here in above but 5 Amp socket outlet on same board

All as per item No 286 here in above but socket outlet 5 Amps independent board complete all as directed by Engr-in-Charge.

All as per Item No 286 here in above but for one 6 pin socket outlet 15 Amps on Independent board with cables 2.5 sqmm size.

S&F Modular switch 1 way 6A,1 module , 240 volts ISI marked complete all as specified and directed

S&F Modular switch 1 way 16A, 1 module , 240 volts ISI marked complete all as specified and directed

S&F Modular Socket, 6A - 2/3 pin combined 2 module, , 240 volts ISI marked complete all as specified and directed

S&F Modular Socket 6A/16A - 2/3 pin combined 2 module, , 240 volts ISI marked complete all as specified and directed

S&F Modular Fan step regulator, 120W 1 module , 240 volts ISI marked complete all as specified and directed

S&F Modular bell push 6A 1 module.

S&F bulk head luminaries IP65 with opal diffuser 10 watt, 230 Volts LED type complete with 10 watt LED Bulb all as directed Engr-in-Charge.

S&F LED lights fitting 1x 20W, 220V, AC , PVC Batten 20 watts driver, holder and power factor >0.90, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Please Enable Macros to View BoQ information