Electrical works for Air compressors and steam generator at ARDC

HINDUSTAN AERONAUTICS LIMITED FACILITIES MANAGEMENT DIVISION

NAME OF THE WORK: "Electrical works for Air Compressors and Steam Generator at ARDC." Cont.No: HAL/FMD/EC-2941/24-25

Name of the Contractor :

BILL OF QUANTITIES WITH SPECIFICATIONS

The tenderers are requested to read the following before quoting:

1 Subject tender has been called on item rate basis. Basic Rate to be quoted for each item.

2 Subject work is a Works contract and prevailing GST of 18% has been added in the BOQ on overall total. Any revision on this GST rate is to HAL account.

3 Sucessful offer that is L-1 (Lowest offer) will be determined including GST.

4 The payment terms shall be governed as per the terms indicated in General conditions of contract.

5 Amount towards GST will be paid along with RAR payment against invoice.

6 The tenderers are requested to abide by the rules of prevailing GST act.

7 This BOQ specification has to be read in conjunction with technical specifications and tender drawings. Any ambiguty in these have to be brought to the knowledge of contract section before submission of tender to avoid future claims/dispute.

Sl. No Specification of item Quantity Unit Rate in Figs excluding GST Rate excluding GST in words Amount Excluding GST in Figs (E=C*A)

1 SUPPLY AND LAYING OF LT CABLES

Supply & laying in the already excavated cable trench/cable tray/fixing on wall/duct wall with necessary M.S clamps / encasing in pipes etc., testing & commissioning of following size XLPE insulated Copper (cu) conductor 1100V gr., earthed Armoured (Arm)U.G cables as directed and as per technical specification and as detailed below. (Note:- Excavation, sand & Brick Protection, concrete cutting, reconcreting, casing pipes will be measured separately.)

a) 3.5 CX 95 Sqmm Copper conductor armoured LT UG cable 100 Mtrs 0.00

b) 3.5 C X240 Sqmm copper conductor armoured LT UG cable 55 Mtrs 0.00

2 END TERMINATIONS

Supply and connecting indoor type cable end joints for the following size 1.1 KV gr., Copper (Cu) conductor XLPE insulated armoured (Arm) LT UG cables by employing necessary glands, terminals(Cu), bolts & nuts etc., complete in all respects and as detailed below:

a) 3.5 CX 95 Sqmm Copper conductor armourd LT UG cable 4 Nos 0.00

b) 3.5 C X240 Sqmm copper conductor armoured LT UG cable 4 Nos 0.00

3 MCCB WITH MS ENCLOSURE

a) Supply, fixing on wall/grouting to floor upto 1200mm above ground level as per site requirement using suitable size MS angle iron frame work finished with two coats of enamel spray paint over a good primer, testing and commissioning of 250A 4P 415V gr. MCCB in a factory built powder coated sheet steel enclosure, MCCB shall be adjustable with thermal settings (80% to 100%), overload and short circuit releases including door interlocking device, front operating handle complete,ON and OFF indication of LED module etc. complete in all respects. including suitable cable end box(incoming/outgoing) wherever necessary complete in all respects and as directed by Engineer-in-charge. (scope includes MS frame work as per requirement) 1 No 0.00

4 EARTHING AND EARTH CONTINUTY

a) Supply & providing earth stations using 600x600x6mm thick G.I plate electrode complete with 2.7 mtr long required quantity of charcoal and salt including excavation, refilling consolidating the soil and providing brick masonry chamber of internal size 300x300mm including providing 50mm thick RCC cover, 40mm dia G.I pipe for watering, water funnel, 2 runs of 32X6mm GI strip from earth electrode lead upto the top of earth pit complete in all respects as directed by Engineer incharge. 2 Nos 0.00

b) Supplying & Laying 25 mm X 5 mm GI strip on surface or in recess for connections joint should be done by welding/overlaping and with 2set of GI bolt and nuts and bolts wirh spring washer etc. as required and as per directed by Engineer In Charge 50 Mtrs 0.00

5 CIVIL WORK (TRENCH WORK IF REQUIRED)

a) Supplying, mixing and placing plain cement concrete (1:2:4) (1 Cement : 2 coarse sand derived from natural sources : 4 graded stone aggregate) of required thickness using 20 mm nominal size down graded hard stone/granite aggregate in accordance with IS 456 in posts, struts, buttresses, string or lacing courses,parapets, coping, bed blocks, anchor blocks, plain window sills, fillets,sunken floor etc including formwork, mechanical mixing, transporting, vibrating, consolidation, levelling, curing, dewatering if any, all materials, labour, lead & lift, tools, plant & machinery, keeping concrete well wetted during the curing period and protecting it in extreme weather conditions etc., but excluding the cost of centering, shuttering and finishing, all complete as directed by the Engineer-in-Charge. 8 Cum 0.00

b) Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains, pipes, cables etc. in all kinds of soils (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lifts, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m with all labour, tools & tackles, plant & machinery, hire & fuel charges etc., all complete as directed by Engineer-incharge. 8 Cum 0.00

c) Returning / filling in with useful excavated soil (excluding rock), free from salts, organic or other deleterious matter (Other than black cotton soil & rock etc., in trenches, plinth,sides of foundations etc., spreading in layers not exceeding 20 cm thick, watering, breaking / removing clods exceeding 50 mm, ramming and consolidation of each deposited layer etc., with all labour, tools & tackles, plant & machinery, etc., lead upto 50 m and for all lifts, all complete as directed by the Engineer-in-Charge. 2 Cum 0.00

d) Supplying, mixing and placing plain cement concrete (1:2:4) (1 Cement : 2 coarse sand derived from natural sources : 4 graded stone aggregate) of required thickness using 20 mm nominal size down graded hard stone/granite aggregate in accordance with IS 456 in posts, struts, buttresses, string or lacing courses,parapets, coping, bed blocks, anchor blocks, plain window sills, fillets,sunken floor etc including formwork, mechanical mixing, transporting, vibrating, consolidation, levelling, curing, dewatering if any, all materials, labour, lead & lift, tools, plant & machinery, keeping concrete well wetted during the curing period and protecting it in extreme weather conditions etc., but excluding the cost of centering, shuttering and finishing, all complete as directed by the Engineer-in-Charge. 1 Cum 0.00

e) Brick work with 230mm/115mm thick common burnt clay machine moulded modular bricks of class designation 7.5 in brick work above plinth level including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand) all complete as directed by the Engineer-in-Charge. 3 Cum 0.00

f) Plastering to internal brick/block wall with 15 mm thick on the rough side of single or half brick wall of cemnet mortor (1:6) including leveling,curing and making the level smooth and at all heights, complete as per direction of Engineer-in-charge. 40 Sqm 0.00

g) Structural steel work riveted, bolted or welded in built up sections, trusses and framed work using members like MS members made up of elements like ISMB,ISMC, ISA, MS Flats, ISNT, MS Plates, holding down bolts, nuts, washer, etc , including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 500 Kgs 0.00

h) Providing and applying synthetic enamel paint for wooden/steel surface in Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture,filling joints,patti etc ,complete as per direction of Engineer-in-charge. 8 Sqm 0.00

i) Demolishing cement concrete manually/by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge. Nominal concrete 1:4:8 or richer mix (i/c equivalent design mix)and including stacking material complete as per direction of Engineer-in-charge. 2 Cum 0.00

Total Amount Excluding GST 0.00

Add 18% GST 0.00

Total Amount Including GST 0.00

Total Amount inclusive of GST In Words

HINDUSTAN AERONAUTICS LIMITED

Facilities Management Division

Pre-Qualification Profile (To Be uploaded along with Part A)

Tender Ref No. or Contract No.: HAL/FMD/EC-2941/24-25

Name of Work: Electrical works for Air Compressors and Steam Generator at ARDC.

Estimated Amount in Rs.: 1265000

Tender Notice Date: [DD/MM/YYYY] 10-23-24

PROVISIONAL GST ID NO. for HAL 29AAACH3641R1Z3

Sl.No Description Details Enclosed / Not Enclosed Remarks

1 Name of the Individual / Firm / Company: * Mandatory Please Enter Name of the Individual /firm /company

2 Type of ownership PleaseEnter Type of Ownership

If Other, please specify

3 Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, etc., Please enter Details of Constitution

4 Address for correspondence: Please Enter Address

5 Bank(s) details: [Copy of the cheque leaf to be uploaded]

Bank Account No. Related Document to be Uploaded to eProcurement Portal (Note Cancelled cheque leaf to be uploaded)

Name of the Bank

Type of Account

6 PAN No.: Please Enter Pan NO

7 Average annual financial turn over during the last 3 years, ending 31st March of the previous financial year [ should not be less than 30% of Amount put to tender] 4999999 3

YEAR TURN OVER IN Rs: Enclosed / Not Enclosed REMARKS 5000000 2

2022 – 2023 Rs: Please Enter Turn over in Rupees for all the 3 years 7499999 2

Average annual Financial turn over 0.00 379500.00

Avg Annual Turnover criteria is not met 10000000 1

8 Details of Registered Contractor

If Registered Contractor with HAL Yes/ No [for Similar nature of work] Documentary proof to be Uploaded to e-Procurement Portal * Category: E = 75.00 Lakhs upto ` 100 Lakhs F = 50.00 Lakhs upto ` 75 Lakhs G = 25.00 Lakhs upto ` 50 Lakhs H =10.00 Lakhs upto ` 25 Lakhs I = 5.00 Lakhs upto ` 10 Lakhs J = 2.00 Lakhs upto ` 5 Lakhs K = Below ` 2 Lakhs 0 7 E 1

Registration No. 199999 7 F 2

Category 200000 6 G 3

PEMD Amount ( If paid ) 499999 6 H 4

9 PF No.: Please Enter PF NO

10 ESI No.: Please Enter ESI NO

Location of Agency/organisation: Please Enter GST Details

Any Special Status of the Unit i.e. DTA, EOU, SEZ, FTWZ

Registered under regular scheme or Composition Scheme or Not Registered Related Document to be uploaded in ePortal

12 Contact details

Contact person name Please Enter Contact person Name

Mobile No. Please Enter Mobile No

Ph. No. with STD code

FAX No. with STD code #N/A #REF!

13 Valid Electrical contractor license of appropriate voltage (Minimum 650V) issued by any state Govt. under clause 45 of Indian Electricity Rules 1956 or as amended from time to time Please SELECT YES OR NO

14 I.T Returns for past 03 years 999999 5 J 6

Assessment year 2023-24 Please Select 'Yes' ' No' for IT Return for All Three years 1000000 4 K 7

Assessment year 2022-23 2499999 4

Assessment year 2021-22 2500000 3

15 Latest Bankers Solvency Certificate from Nationalized/ scheduled Bank issued within a period 12 months from the final date of submission of tender. solvency cal

Name of Bank & Branch: Please Enter Details to 'Name of the Bank' , 'Date of Issue','Value in C89``Rs. in Lakhs 10-23-24 28-Jun 0 40000

Date of Issue[MM/DD/YYYY]: 200000 40000

Value of Rs. In Rupees: 200001 150000

Solvency value is NOT as per NIT

16 Experience of having successfully completed similar works during last 7 years ending on the previous day of submission of tender should be either of the following: [Work completion certificates along with LOA/PO/WO should be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated amount put to tender. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated amount put to tender. (iii) ONE similar completed work costing not less than the amount equal to 80% of the estimated amount put to tender. 506000 500001 250000

Completed similar works during last 7 years Please Select %of similar works completed during last 7 years 1000000 250000

Work No I Type of Work: [Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 1000001 500000

Brief Description of Work: 2000000 500000

Completed value of Work in Rs. Lakhs: 2000001 1000000

Date of Commencement of Work [DD/MM/YYYY] 4000000 1000000

Date of Actual Completion of Work[DD/MM/YYYY]: 4000001 2000000

Work No II Type of Work: [Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 10000000 2000000

Brief Description of Work: Please Enter Details for Work No II

Completed value of Work in Rs. Lakhs:

Date of Commencement of Work[DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]: work done

Work No III Type of Work: [Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 10-23-24 2555

Brief Description of Work: Please Enter Details for Work No III 10-25-17

Completed value of Work in Rs. Lakhs:

Date of Commencement of Work[DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

17 Details of person holding the power of Attorney :

Name Related Document to be Uploaded to eProcurement Portal

Mobile No. Please Enter Details for Person holding Power of Attorney

Ph. No. with STD code

FAX No. with STD code

18 DECLARATION I

The document being viewed / downloaded from the website and having read & understood all the contents of the tender document mentioned under Pre-qualification criteria, technical bid ( Page 1 to 169) and price bid do hereby accept all the terms and conditions laid down in the said Tender document and will abide by the same on acceptance and award of work. Please Accept the Declaration I

19 DECLARATION II

I/We declare and confirm that - 1. All information and attachments submitted along with this offer are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my offer . 3. I/We shall not make refund claims of expenditure incurred in processing this offer. 4. I//We are aware that document sought only be uploaded for evaluation of offer. 5.I/We shall not associate nor has been associated in the past, directly or indirectly with consultant or any other entity that would prepare the design, specification and other documents of the project. Please Accept the Declaration II