REPAIR TO FLOORING, PLASTERING, JOINERY AND PLUMBING WORK FOR ZONE-II AREA UNDER AGE B/R-I OF GE NAGROTA.

Amount

Demolition of brick work / stone masonry built in cement mortar or cement lime mortar including all quoins ,arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and directed.

M&L brick work with sub class 'B' bricks in 1:6 cement mortar on straight or curved on plan exc 6 m , complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, all as specified.

Taking down chowkat with shutter (without taking off shutter from the frame) not exceeding 1.5 sqm each, complete all as specified and as directed at site.

Taking down chowkat with shutter (without taking off shutter from the frame) exceeding 1.5 sqm but not exceeding 4 Sqm each complete all as specified and as directed at site.

Taking down shutters of any description exc 1.00 Sqm and n.exc. 2.00 Sqm each complete all as specified and as directed at site.

Refixing shutter of any description n.exc. 1 sqm each in the same opening including taking down and easing and adjusting, complete all as specified and directed.

Refixing shutter of any description exc. 1 sqm each and n.exc. 2 sqm in the same opening including taking down and easing and adjusting, complete all as specified and directed.

Pressed steel door frame of size 125 mm x 60 mm with one or more rebates using 1.25 mm thick PBI sheet including necessary fixing lugs, lock strike plate including one shop coat of zinc chromate primer, complete all as specified and directed.

All as per item No.9 here-in-before but 105x60 mm.

S & F 35 mm thick second class hard wood, factory made, plain, framed, panelled shutters (two numbers of panels) with lock rail and panel of 9 mm BWP commercials ply or 12 mm veneered particle board on both faces. The size of rails and size as per IS:1003 (Part-I), Kiln seasoned & chemically pressure treated, complete all as specified and directed.

S & F 35 mm thick second class hard wood, factory made, glazed and skelton shutters, open rebated and prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamered or rounded, fitted with cut and mitred beads for securing glass, etc. Size of memebers of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) for doors, complete all as specified and directed.

Box type steel window/ ventilator side hung double shutters with provision for desert coller/AC (Inside for wire mesh & outside for glass), including guard bar hinges, steel handle, tower bolt and steel peg stay complete with glazaing bar dovetailed for welded and fixed steel window shall be conforming to relevant IS complete all as shown on drawing No CEUZ/TD/1302/09, Sh 1/3 to 3/3 including taking down of existing steel windows, complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured and paid separately.

S & F factory made solid PVC door frame of size 50mm x 47mm ,ade pit pf 5mm plain colour PVC sheet reinforced with MS square tube as per specification and drawing, complete all as specified and directed.

S & F 30 mm thick (style) Factory made solid panel PVC door shutter consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

S & F anodized aluminium frame for doors, windows ventilators with one or more rebates including jointing cleat for fixing etc, complete all as specified and directed.

S&F Powder Coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

S & F in repairs aluminium anodised window and ventilator shutters side hung type without sash bar, aluminium sections weigthing 0.55 kg/m including necessary jointing cleats, glazing clips rubber packing, aluminium snap beading screwes anodized aluminium fittings such as peg stay 150 mm long(1 No) hinges type B-21 100 mm long 2 Nos suitbale handle 1 Nos, complete all as specified and directed.

M & L for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repairs, complete all as specified and as directed.

S&F in repairs, Aluminium (extructed section) body door Closer hydraulically regulated, designation No 3, universal type, suitable for door shutter of 851 to 1000 mm in width and of weight between 61 to 80 Kg, complete all as specified and directed.

S & F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm dia and fixed with tinned tacks or galvanised mild steel staples, complete all as specified and directed.

S & F in repairs 3.00 mm thick Sheet glass ordinary quality and glazing with oil putty and pin(steel spring for fixing glass) in square n exc 0.5 Sqm in each pane, complete all as specified and directed.

3 mm thick pin head glass, ordinary qaulity,in sqaures n exc 0.5 sqm each panes etc complete all as specified and directed.

M&L for 40 mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in floors, complete all as spd and directed.

S & F 250 mm long aluminium alloy, anodized sliding door bolt with hasp stapple ( bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed.

S & F 150 mm aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified and directed.

All as per item No. 26 here-in-before but 100 mm long.

S & F 100 mm long butt hinges, medium weight, cold rolled mild steel fixed with screws or welding complete all as specified and directed.

S & F 125 mm aluminium handles cast type anodized, complete all as specified and directed.

All as per item No.29 here-in-before but 100 mm long.

300 mm mild steel oridinary rat tail rod pattern springs including roller and roller plates, complete all as specified and directed.

M & L for Prepration of new or previously painted wooden surfaces any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

S&F in repairs, stainless steel sink, 1.00 mm thick for kitchen or laboratory with plug, waste pipe, washers including bedding in cement mortar on to dwarf wall or fixing cantilever cast iron brackets connecting union etc., over all size 915 mm x 460 mm with bowl size 410 mm x 330 mm x 160 mm with waste coupling, complete all as specified and directed.

S & F in repairs 10 Ltrs capacity PVC valveles, less symphonic action type, flushing cistern low level, white with inlet, ball valve, float and handle including bracket, complete all as specified and directed.

S&F in repairs 15mm bore Bib taps, cast copper alloy with crutch or butterfly handle,screwed down,screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed by Engr-in-Charge.

Brass CP mixer 15mm bore for mixing hot and cold water screwed down for iron pipe and fixed, complete all as specified and directed.

S & F in repair for PVC connections pipe 15 mm size, with PTMT nuts of length 450 mm, complete all as specified and directed.

S & F in repairs, self cleaning water jet, chromium plated, (HEALTH FUSET) 15 mm bore with all accessories complete suitable for EWC as approved, complete all as specified and directed.

S & F in repairs, swivel shower of PTMT any colour for finsing with 15 mm dia pipe (minium weight 40 gms), complete all as specified and directed.

S & F in repairs shower arm 15 mm size 195 mm long with bend of 45 degree with flange of PTMT any colour (Min weight 40 gms), complete all as specified and directed.

Taking or down 15 mm bore steel tubing and connection including cleaning for refixing or removal to store, complete all as specified and directed.

M&L 15 mm bore unplasticised PVC pipes of pressure rating 10 kg/cm2 fixed to walls, ceiling or in floors etc( as union, tee, socket, nipple, elbow) complete all as specified and directed

Taking up or down 20 mm bore steel tubing and connection including cleaing for refixing or removal to store complete all as specified and directed.

All as per ser item no. 43 here in above but 20 mm bore.

Vitreous china wash basin, white, flat back, size 550X400 mm including waste pipe, bracket and cutting for and pinning in ends of brackets or errecting stand but excluding taps, chain and plug complete including taking down existing old WHB all as specified and directed.

S & F 15 mm pillar tap, chromium plated, screwed down high pressure with and without levelled hot or cold with long screwed shanks and fly nuts screwed for pipe and fixed in repairs, complete all as specified and directed.

S&F 15mm bore stop valves, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle.screwed both ends for iron pipe or for unions and fixed in repairs, complete all as specified and directed by Engr-in-Charge .

S&F in repairs towel ring of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats 9min wt 90 gm) complete all as specified and directed.

S&F in repair CP brass screw and wooden /plastic cleats towel rail of 600mm length all as specified and directed.

S&F for 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified.

S&F in repairs PVC (SWR) Bends any radius for 110mm bore.

Stack clamps out of 50mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends to wall or roof complete all as specified and directed.

S&F PVC grating round 100 mm size of PTMT (minimum weight 25 gms), complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor tap, plain with grating including jointing with solvant cement,complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc including raking out joints, hacking for key, scrubbing down with water complete all as specified.

M & L for rendering 15 mm thick on external surfacesd of wall in CM 1:4 finished even and smooth without using extra cement, complete all as specified and directed.

M&L rendeing 5 mm thick in CM 1:4 as in ceiling, soffit of chajja etc complete all as specified and directed

M & L for rendering 10 mm thick on internal surfaces of wall in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed.

Preparation of new plastered wall surface and applying two coat of cement base paint all as specified and directed.

M&L preparing new plastered surfaces of internal walls and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed.

M & L preparing new plastered surfaces of ceiling chajjas facia etc. and applying three coats of white wash,complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness ( below or above ground level) complete, all as specified.

M/L 100 mm thick Cement concrete type B2, 1:2:4 (using 40 mm graded granite stone aggregate) in base of flooring/ hard standing finished evern & smooth w/o using extra cement.

M&L Plain cement concrete 75 mm thick, type C-1, 1:3:6 (using 20 mm graded crushed stone aggregate) as in plinth protection finished the surface even and smooth without using extra cement, complete all as specified and directed.

Dismantling floor , hearth or wall tiling including cement mortar bedding ( but not backing ), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M & L for 15 mm thick screed bed or bedding layer of mortar for laying floor finishes in cement motar 1:4 finished rough complete all as specified and directed.

M & L Rendering 10 mm thick in cement mortar (1:3) as in backing layer for laying of tiles in vertical surfaces complete all as specified & directed.

M & L for non skid ceramic colour tiles 7 to 8 mm thick ( square/rectangle) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles complete all as specified and directed.

M&L Non skid ceramic colour tiles 7 to8mm thick ( square/rectangle) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm,in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement complete all as specified and directed

M&L Glazed ceramic coloured tiles 300x 200 x 6 to 7 mm thick as in vertical surfaces such as dado,skirting set jointed in neat cement slurry including pointed in white or coloured cement to match with the shade of tiles, complete all as specified and directed.

M&L chequered cement tiles concrete 25cm x 25 cm x 22mm thick, set jointed in neat cement slurry in floor ,complete all as specified and directed.

Dismantling of wrought iron or mild steel work in any description, complete all as specified and directed.

S&F Mild steel Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165, complete all as specified and directed.

M&L preparation of new steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

S&F in repair harrison rails, mild steel, chromium plated with fixing brackets, stops, roller etc complete all as specified and directed.

Dismantling water tank and removing to stores exc 500ltr n.exc 1000ltr

Dismantling water tank and removing to stores exc250ltr n.exc 500ltr

S&F Rotational moulded polyethlene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of Capacity 1000 litres including all accessories complete, all as specified .

All as per ser item no. 79 here in above but 500 ltr

S&F 20 mm dia Ball valve PTMT valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule.

S&F in repair seat cover for peddastel patern complete all as specified and directed

S&F 12mm thick frosted tinted glass and glazing in square fixed with aluminium frame work icluding necessary jointing cleats , loking arranements, handles two nos etc complete all as specified

Taking down existing old tarfelt, bituminous compound including cleaning & removing debris to a distance exc 100 m but n.exc. 250 m complete all as specified and directed

M&L for providing cement concrete 1:2:4 type B-0 (12.5mm grade aggregate) as in roof kerbs or mud stops,rounded or chamferred on edges or as in padding concrete complete all as specified and directed.

M&L for 10 mm rendering in CM 1:4 including water proofing compound @2% of cement over roof surfaces finished even and smooth without using extra cement complete all as specified. Note:- WPC Measured and Paid Separately.

Supply only integral water proofing compound, complete all as specified and directed.

M&L for Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces complete all as specified and directed.

Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq m including cleaning surfaces complete all as specified and directed.

M&L for One layer of APP based polymeric membrane of approved manufacturer, 3mm thick, weight not less than 3.50 Kgs per Sqm , reinforced with non woven polyester fabric or weight not less than 150 gms per Sqm . Polymeric membrane shall be taken to a height 60 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing(Note (i) Laying of APP based polymeric membrane shall be done by torch on method or as per manufacturers instructions (ii) A Minimum overlap of 100 mm and 75 mm should be made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as manufacturers instructions NOTE : S&F of APP based polimeric membrane of approved manufacturer will be laid/fixed by authorised person of the same manufacturers units asper relevent IS.

Dismantling plain or corrugated steel sheeting, any gauge, thickness in roof covering and removing from site of work, complete all as specified and directed.

S & F prepainted galvatume aluminium zinc coating GI based corrugated/profile steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof coveing/cladding to wall fixed with self tapping screws/L-type or J-type or cranked hook bolts in lieu of screw as per manufacturer instruction, complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Deduction to be made from BOQ for schedule of credit (Sch 'A' Part - II) Amount of ₹ 57,750.00 during AOC Note:- Tenderers shall not quote for this Schedule

Kalsi Engineers and contractors

M/S Shankardass Devidass

U K Engineering Works

M/S MANISHA BUILDERS