Supply and fixing of Furniture in various blocks at Haridev Joshi University at Dahami Kalan, Jaipur (Phase-I)

Amount

Supplying & Placing Reception Counter with marble/quartz stone in completely knock down conditions with an overall size 2400mm X 900mm X 1035mm that is to be assembled at site. The top shall be made from 25mm thick plain MDF board with 15mm thick marble/quartz stone. The top shall be supported frame made from CRCA tube. Rectangular Frame shall be Fabricated component in 1.2mm thick CRCA tube. The Modesty & Side panels made 25mm thick plain MDF board with 1mm thick decorative laminate and all edges are duly sealed with 2mm thick PVC Edge banding. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The table shall have upper top shelf made from 18mm thick plain MDF board with 1mm thick decorative laminate and all edges are duly sealed with 2mm thick PVC Edge banding. All edges are duly sealed with 2mm thick PVC Edge banding. The Screw joining Wooden Panels to under structure are Chip Board Screws. Glides crews is provided at the bottom of the legs for Level adjustment. Grommets (cut outs) is provided on table top for cabling. Grommets is provided with PVC cover. Mobile pedestals is fixed below the top. Mobile pedestals made of 18mm thick plain MDF board with 1mm thick decorative laminate & all edges are duly sealed with 2mm thick PVC Edge banding. The sides of drawers and facia made of 18mm thick plain MDF board with 1mm thick decorative laminate & all edges are duly sealed with 2mm thick PVC Edge banding. Pedestal should be supported to the table top. Pedestals have 3 drawer 2 for personal and 1 for lateral files. Drawers are provided with single extension telescopic ball bearing slide channels. Pedestal is provided with single central locking system, SS handles. Lock, Hinges, Telescopic channels shall be of make Hettich / Ebco / Ozone or equivalent. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and supplying Medium Back Revolving chair with ergonomic design, comfortable & aesthetically appealing. Seat : (W)51.0cm x (D) 52.5cm. Seat made of 12mm thick hot pressed plywood with moulded polyurethane foam 50mm thick having density 45kg/m³ upholstered with mesh fabric. Size of back shall be (W)-48.5cm x (H)-62.0cm. The back shall made up of two piece injection moulded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main assembly. Armrest shall be in injection moulded PP arm. The mechanism of chair shall have following features: The center tilt mechanism shall be designed as-360° revolving type, 17° ±2° maximum tilt on pivot at center, Upright position locking, Tilt tension adjustment. Spine bracket shall made of Aluminium die cast piece connecting back with mechanism. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The bellow is 3 piece telescopic type and injection molded in black polypropylene. The pedestal is injection molded in black 30% glass filled Nylon. A 10.5 dia forged bright zine plated M.S. caster pin shall be press-fitted into each prong for holding the castors. The pedestal shall be 700 mm pitch centre dia. (750 mm with castors). The twin wheel casters are made of nylon . Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min 96.0 to max 106.0 cm. Seat height - min 46.0cm to max 56.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and supplying centre table with an overall size 1200mm X 600mm X 450mm. The top shall be made up of 25mm thick Pre Laminated MDF Board. The profile shall be in rectangle shape and all edges are duly sealed with 2mm thick PVC Edge banding. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The under structure shall consist of SS 202 grade pipe frame of size 50x25x1.2mm thick. There shall be shoe provided at the bottom to avoid scratches on the floor. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and supplying Corner Table with an overall size 600mm X 600mm X 450mm. The top shall be made up of 25mm thick Pre Laminated MDF Board. The profile shall be in rectangle shape and all edges are duly sealed with 2mm thick PVC Edge banding. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The under structure shall consist of SS 202 grade pipe frame of size 50x25x1.2mm thick. There shall be shoe provided at the bottom to avoid scratches on the floor. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & placing storage unit with an overall size 1500mm X 450mm X 750mm. Table top & side made of 25 mm thick plain MDF board clad with 0.6 mm thick post formed laminate and 0.6mm thick Backing Laminate.-Flat edge duly sealed with 2mm thick PVC Beading. Modesty panel made of 18mm thick Pre Laminated MDF Board. All exposed edges are sealed with 2mm PVC edge beading. The body, drawer, shutter, shelves and all other are made from 18mm thick Pre Laminated MDF Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The storage shall have 8 nos. of drawer, 1 nos. of adjustable shelf with 2 nos. of shutter. Drawers are provided with single extension telescopic ball bearing slide channels. with single central locking system and concealed crank hinge with SS handle. There shall be buffers provided at the bottom to avoid scratches on the floor. Skirting shall be provided at bottom. Lock, Hinges, Telescopic channels shall be of make Hettich / Ebco / Ozone or equivalent. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing, supplying and placing magazine stand Dimension: Overall size: Height: 1850 mm x Width: 900 mm x Depth: 450 mm. Construction & Material: CRCA Sheet for shelf & anodized screws. Welded construction.0.8 thickness High yield strength CRCA for back. 0.8 thickness for all other components. It should be supplied with 5 nos. of rolling shelves. Leveller: M10 screw type leveller with hex plastic base. The complete steel structure shall be constructed by welding and welding part should be done by Robotic MIC welding. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying and placing of 3 Seater Waiting Sofa . The seat and back shall be made up of high quality cold rolled MS perforated sheet, pressed and welded to form the shape. Perforated seat and back shell made of high quality MS sheet of 1.2mm thick. The armrest and legs shall be made up of mild steel powder coated tube with 1.2 mm thick. Overall size: 1750mm (L) X 750(H) X 560(D) and seat height 420mm. The entire MS sheet cutting should have through NC sheet metal cutting machine, the entire sheet metal banding should have through CNC sheet metal bending machine & the entire MS sheet perforation should have through metal perforated machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. The cushion Seat & back shall be made up of 9 mm thick plain mdf board upholstered with high resilience polyurethane foam having density 35Kg/m³. The seat and back shall be padded with leatherite tapestry. Cushion Seat & back screwed on the three seater bench with screw. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying and placing of Executive 3 Seater Sofa(Airport sitting type)- The seat and back shall be made up of high density polyurethane (PU) with metal frame inside. The armrest and legs shall be made up of die casting aluminum alloy with polish treatment and sprayed with static powder. Beam made of hexagonal metal tube. Overall size: 1775mm (L) X 845(H) X 605(D) and seat height 440mm All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and supplying of two seater desk & bench for step type classroom. First Module: The Complete MS section to be powder coated in approved based high gloss colour. Vertical supporting pipe is to be made of 80x30 mm elliptical shape pipe with 2.0 mm wall thickness to be connected with 50x50x1.6mm horizontal supporting pipe and 1.2mm thick modesty. The Modesty panels made of 1.2 mm thick CRCA sheet with perforation of dia 3mm on the sheet shall be uniform except 100mm four side border. Perforated curved modesty with both side of vertical pipes. 20x20x1.6mm square pipe to be used for strengthening the border of modesty. The entire MS sheet cutting should have through NC sheet metal cutting machine, the entire sheet metal banding should have through CNC sheet metal bending machine & the entire MS sheet perforation should have through metal perforated machine. BASKET : Basket shall be Made of 6mm thick Mild steel rod making a curved basket connected with the 50x50 mm square pipe support. FIXING: Fixing at site to be done with metal dash fasteners of 100x12 mm size grouted with chemical filter compound . Pedestal made of 2mm thick pressed HR steel base and shall be ribbed with 2 counters sunk holes for floor fixing. The front row have full MS modesty panel. Desk Top made up of 25 mm thick pre laminate particle board - edge duly sealed with 2mm thick PVC Beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. 25x3mm MS angle shall be used for top supporting. The complete steel structure shall be constructed by welding and welding part should be done by Robotic welding machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. Size: Desk height- 750mm +/- 10mm, Top Size - 1200mm(W)x420mm(D) +/- 10mm. Middle Module: The Complete MS section to be powder coated in approved based high gloss colour. Vertical supporting pipe is to be made of 80x30 mm elliptical shape pipe with 2.0 mm wall thickness to be connected with 50x50x1.6mm horizontal supporting pipe and 1.2mm thick modesty. The Modesty panels made of 1.2 mm thick CRCA sheet with perforation of dia 3mm on the sheet shall be uniform except 100mm four side border. Perforated curved modesty with both side of vertical pipes. 20x20x1.6mm square pipe to be used for strengthening the border of modesty. The entire MS sheet cutting should have through NC sheet metal cutting machine, the entire sheet metal banding should have through CNC sheet metal bending machine & the entire MS sheet perforation should have through metal perforated machine. BASKET : Basket shall be Made of 6mm thick Mild steel rod making a curved basket connected with the 50x50 mm square pipe support. FIXING: Fixing at site to be done with metal dash fasteners of 100x12 mm size grouted with chemical filter compound . Pedestal made of 2mm thick pressed HR steel base and shall be ribbed with 2 counters sunk holes for floor fixing. Desk Top & Seat made up of 25 mm thick pre laminate particle board - edge duly sealed with 2mm thick PVC Beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. 25x3mm MS angle shall be used for top supporting and Seat shall be mounted on 25.0mm dia. & 1.6mm thick pipe.The complete steel structure shall be constructed by welding and welding part should be done by Robotic welding machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. Size: Desk height- 750mm +/- 10mm, Top Size -1200mm(W)x420mm(D) +/- 10mm, Seat Size:1200mm(W)x400mm(D) +/- 10mm, Seat height – 450mm+/- 10mm. Last Module: The Complete MS section to be powder coated in approved based high gloss colour. Vertical supporting pipe is to be made of 80x30 mm elliptical shape pipe with 2.0 mm wall thickness to be connected with 50x50x1.6mm horizontal supporting pipe and 1.2mm thick modesty. The Modesty panels made of 1.2 mm thick CRCA sheet with perforation of dia 3mm on the sheet shall be uniform except 100mm four side border. Perforated curved modesty with both side of vertical pipes. 20x20x1.6mm square pipe to be used for strengthening the border of modesty. The entire MS sheet cutting should have through NC sheet metal cutting machine, the entire sheet metal banding should have through CNC sheet metal bending machine & the entire MS sheet perforation should have through metal perforated machine. BASKET : Basket shall be Made of 6mm thick Mild steel rod making a curved basket connected with the 50x50 mm square pipe support. FIXING: Fixing at site to be done with metal dash fasteners of 100x12 mm size grouted with chemical filter compound . Pedestal made of 2mm thick pressed HR steel base and shall be ribbed with 2 counters sunk holes for floor fixing. Seat made up of 25 mm thick pre laminate particle board - edge duly sealed with 2mm thick PVC Beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Seat shall be mounted on 25.0mm dia. & 1.6mm thick pipe. The complete steel structure shall be constructed by welding and welding part should be done by Robotic welding machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. Seat Size:1200mm(W)x400mm(D) +/- 10mm, Seat height – 450mm+/- 10mm.All as per the layout. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and supplying Table with one side drawers with an overall size -1500mm L X 750mm W X 750mm H. The top and modesty panel shall be made from 18mm thick Pre-Laminated MDF Board. All edges are duly sealed with 2mm thick PVC Edge banding. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Understructure: The top shall be supported on C frame made from CRCA sheet of 0.9mm thick. Rectangular Frame shall be Fabricated component in 1.2mm thick CRCA. Leg should be made from 38mmx25mmx1.2mm thick MS ERW Tube. Wire management horizontal and vertical wire carrier shall be made from 0.8mm thick CRCA sheet. There shall be leveller provided at the bottom made of Nylon. Three drawer pedestal: Shell, drawer tray, Drawer Front, Frame Assembly made of 0.8mm thick CRCA sheet. It should be operated on channel and recessed plastic handle with centralized locking mechanism. Lock shall be of 10 lever cam Lock. Snap fit ABS plastic handle shall be built in plastic. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and fixing of Workstation System : One seater overall size-1200(L) x 600(W) x Height of panel 1200 mm. Side panel and main panel shall be of 60mm. The 60mm panel comprises of 2 nos. Of vertical trims made of aluminum extrusions and Horizontal trims shall be made of aluminum extrusions at every division of tile/block. Block for 60mm panel’s thickness shall comprises of 38mm thick paper honeycomb + 9mm particle board on each sides + 0.6mm decorative laminate or fabric on both sides. The fabric shall be upholstered with particle board framing shall used on outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. Blocks shall be located in the mid segment of the panels and shall be provided with cut outs for mounting switch boxes (above the worktops). Fabricated bottom frame for 60mm panel comprises of L channels made of 2mm thick CRCA steel formed plates of 3mm thick HR steel & ERW steel tube of size 35x15x1.6mm thick in oval cross section welded together. This frame shall be bolted to the uprights with M6 screws. Top tiles shall be slid in to the panels from top before fixing the top horizontal. The top shall have white board / glass/ laminate tiles of approved shade. Laminated tiles shall be 9.0 mm thick pre-laminated particle board having all its edges with minimum 0.5 mm thick PVC edge banding. White board tiles shall be made of 8.0 mm thick particle board laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and having all its edges with minimum 0.5 mm thick PVC edge banding. Glass tiles - 4 mm thick toughened clear glass. Split Top shall be provided for two different finishes in single panels. Bottom tiles shall be press fitted on to the assembly frame of the panel with the help of snap on clips made of nylon and support clips made from PP co polymer. Bottom tiles shall be of Metal tiles made of 0.8mm thick CRC sheet. These uprights and horizontals are made of aluminum extrusion having material & have average wall thickness of 1 mm. The panels shall be joined to each other directly with joinery or with the help of post to form. Free standing modules shall be provided with stability bracket. The top trims and end trims for 60 mm shall be made from aluminum extrusion having material. All kinds of extrusions for 60 mm shall have average wall thickness of 1 mm. Top trim shall be press fitted on the horizontal extrusion. Die cast. aluminum alloy shall be provided according to the joineries. The worktop is made of 25mm thick pre laminated particle board with 2mm thick PVC edges bands all around all the edges are pressed with 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The work surface shall be provided with circular cut out of Dia.65mm for passing of wires. These cut outs shall be provided with ABS covers. Table top height – 750mm (including table top thickness of 25mm) Work surface bracket shall be mounted on to the Horizontal extrusion. 4 numbers of ribs are provided in the work surface for strengthening purpose. All the work surface shall be mounted on the work surface through round Philip head diameter 4 mm x 19 length having finish zinc plated. The panel legs shall provide to support panels. Panel legs shall fabricated by CO2 welding MS Tube of section 38 mm x 25 mm ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm over which an M8 Leveler is fitted, which allows for adjustment of the height by 25mm. Double and single side leg assembly: shall be provided to supporting panels & work surface. Wire carrier shall be made from 0.8 mm thick CRCA sheet. It shall be constructed with two parts, one shall be body & another shall be cover. It holds the cables & gives aesthetic appearance by covering all cables. Worktop supporting pedestal shall be provided having provision to fit with worktop and pedestal leg welded assembly fitted at the bottom. Key board tray made of 1.2mm thick CRCA steel. Adjustable wheel mounted CPU trolley made of 1 mm thick CRCA steel. Pedestal, key board tray & CPU Trolley shall be provided with each workstation. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns.All as per the layout. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and supplying visitor chair with ergonomic design, comfortable & aesthetically appealing. Seat : (W)51.0cm x (D) 52.5cm. Seat made of 12mm thick hot pressed plywood with moulded polyurethane foam 50mm thick having density 40kg/m³ upholstered with mesh fabric. Size of back shall be (W)-48.5cm, (H)-62.0cm. The back shall made up of two piece injection moulded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main assembly. Spine bracket shall made of Aluminium die cast piece connecting back with mechanism. Armrest shall be in injection moulded PP arm. Assembly made from MS ERW round tube of 25mm with 2mm thick with base plate for seat fixing. Bending of Tube Should be done on CNC operated machine to ensure accuracy of bending of tube and welding part should be done by Robotic MIC welding. Visitor Chair frame is chrome coated. Overall Dimensions of Chair: Seat Height -min 45.0cm, Height -min 95.0cm, Width & Depth of Chair as measured from pedestal - Width-50.0 cm and Depth-65.0 cm. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing, supplying and placing steel almirah Dimension: Overall size of Almirah (Excluding Leveler): Height: 1980 mm x Width: 916 mm x Depth: 486 mm. Construction & Material: CRCA Sheet for shelf & anodized screws. Welded construction.0.8 thickness High yield strength CRCA for doors and back. 0.9 thickness for all other components. Locking & Handle: Mazak handle and Three way locking mechanism with shooting bolt. Shelving: Height wise adjustable shelf mounting. Maximum uniformly distributed load capacity per each full shelf is at least 40kg. 4 Nos. of adjustable shelf mounting. It should be supplied with 4 nos. of adjustable shelves i.e. 5 loading compartments. Leveller: M10 screw type leveller with hex plastic base. The complete steel structure shall be constructed by welding and welding part should be done by Robotic MIC welding. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Meeting Table oval shape in completely knock down conditions with an overall size 2400mm X 1200mm X 750mm that is to be assembled at site. Top made up of 25 mm thick pre laminate MDF board and edge duly sealed with 2mm thick PVC Beading. The Side and modesty is made of 18mm thick pre laminate MDF board. All edge sealed with 2mm thick PVC beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The modesty panel shall be connected with both end. Glides crews is provided at the bottom of the legs for Level adjustment. The table top shall have flapper for easy wire management for houses video, audio, data and power connection discretely. Wire management horizontal and vertical wire carrier shall be made from 0.8mm thick CRCA sheet. Raceway shall be provided of MS CRC sheet below the work top as per requirement for inlaying of electrical management and carrying the wire horizontally. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. There shall be buffers provided to avoid scratches on the floor. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Modular Table Type A+: The main desk is provided with the wire management system. The Main table shall be of size: 2400 Length mm x 2200 mm Width x 750 mm height. The worktop shall have the size 2400mm X 1200mm. Top surface of the table shall made up of 36mm (18+18) thick MDF board duly finished with 4mm thick Veneer and final coating of PU high gloss polish and 0.6mm thick Backing Laminate. The Main desk should contain in Smart Case - space slides effortlessly in style. Side panel made up of 36mm (18+18) thick pre laminate MDF board and edge duly sealed with 2mm thick PVC Beading. Modesty made up of 18mm thick pre laminate MDF board. All edge sealed with 2mm thick PVC beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The three drawer unit size- 680(H)x400(W)x450(D). Mobile pedestals is placed below table top. Mobile pedestals made of 18mm thick Pre laminated MDF board. The sides of drawers and facia made of 18mm thick pre laminated MDF Board. Back of the pedestal made of 9mm Pre laminated MDF Board. Pedestal stand-alone and not supported to the table top. Pedestals have 3 drawer 2 for personal and 1 for lateral files. Drawers are provided with single extension telescopic ball bearing slide channels. Pedestal is provided with single central locking system, SS handles. Side Unit Size-1000(W)X450(D)X750(H) mm. Top surface of shall made up of 36mm (18+18) thick MDF board duly finished with 4mm thick Veneer and final coating of PU high gloss polish and 0.6mm thick Backing Laminate. Side panel made up of 36mm (18+18) thick pre laminate MDF board and edge duly sealed with 2mm thick PVC Beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The side, shutter and shelves are made of 18mm thick Pre Laminated MDF Board. All exposed edges are sealed with 2mm PVC edge beading. The back is made of 18mm thick Pre Laminated MDF Board. Each unit have lockable double door is fitted with hinges. Each unit have one numbers of adjustable shelves. Skirting is made of 18mm thick Pre Laminated MDF Board. All exposed edges are sealed with 2mm PVC edge beading. Lock, Hinges, Telescopic channels shall be of make Hettich / Ebco / Ozone or equivalent. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing High Back Revolving Chair Type A+: The back & seat is made up of 1.2 cm. thick hot pressed plywood upholstered with leatherette and moulded Polyurethane Foam. The back foam is designed with contoured lumber support for extra comfort. Back Size: 54.0cm.(W) X 86.0cm.(H) SEAT SIZE: 54.0cm.(W) X 49.0cm.(D).The polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20+/-2 for 25% compression. SEAT-BACK CONNECTING SPINE: The seat and back are arrested together with a 9.0cm (w) spine made of 0.8cm thick. HR steel. The spine is black powder-coated. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. ARMREST ASSY: The armrest assy. comprises of three parts viz. the armrest support tube and P.U. armrest and the armrest top. The armrest tube assy. is made of 2.54cm(1") x 16 BG. M.S. E.R.W. support tubes and Chrome plated. The P.U. armrest is made of black integral skin polyurethane with 50-70 shore 'A' Hardness and reinforced with M.S. insert. The armrest top is made of ABC & upholstered with foam & leather. The mechanism of the chair shall have following features : 360⁰ revolving type, Knee Tilt system, 5-position locking with antilock back mechanism. Tilt tension adjustment and position locking with anti-shock back mechanism, which prevents the backrest from impacting the user when the lock is released. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished aluminum it shall be fitted with 5 nos. twin wheel castor. The size of the pedestal shall be 62.0 +/- 1.0 cm pitch-centre-dia (70.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black nylon. Overall dimensions of Chair shall be, Width of Chair - 70.0cm, Depth of Chair - 70.0 cm as measured from pedestal below with castor. Height from ground - min 122.0 to max 132.0 cm. Seat height - min 46.0cm to max 56.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and placing of visitor chair Type A+: The seat is made up of 1.2 cm. thick hot pressed plywood upholstered with leatherette and moulded Polyurethane Foam. The back foam is designed with contoured lumbar support for extra comfort. BACK SIZE 52.0cm. (W) x 68.0cm. (H) SEAT SIZE: 52.0cm. (W) x 49.0cm. (D) POLYURETHANE FOAM: The polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 on Hampden machine at 25% compression. SEAT-BACK CONNECTING SPINE: The seat and back are arrested together with a 9.0cm (w) spine made of 0.8cm thick. HR steel. The spine is black powder-coated. The tubular frame shall be cantilever type & made of 40x20x2 mm thick capsule tube. Bending of Tube Should be done on CNC operated machine to ensure accuracy of bending of tube. Overall Dimensions of Chair shall be Seat Height -46.0cm. Height -99.0cm, Width & Depth of Chair as measured from pedestal - Width-57.0 cm and Depth-68.0 cm. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Sofa Set (3+1+1 Seater)Type A+: Size of 1 seater sofa shall be 1010 (L) x 920 mm (W) x 950 (H) seating area length 560 mm & seating area width 510mm. Size of 3 seater sofa shall be 1960 (L) x 920 mm (W) x 950 (H) seating area length 1520 mm & seating area width 510mm. The frame material to be tropical wood + pinewood, Length of S-spring to be 510 mm, width of belt to be 40mm.There should be pocket on each side of sofa. The seat foam & back foam density to be 40kg/m3 upholstered with leatherette. The material for leg and on the front of sofa side to be teak wood and should be polish. Sofa handle to be wood and should be polish. The leg should be fixed with wood screw provided on frame in addition to M-8 / T-nut. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Center Table: The dimension of the table shall be (L) 1200 mm x (W) 600 mm x (H) 450mm, the material of the top shall be plywood with VENEER 18mm thick. The table support to be made of teak wood of size- 55x22mm. Center Table Leg to be made of teak wood of size - 50x50mm & should be polished. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Corner Table: The dimension of the table shall be (L) 600 mm x (W) 600 mm x (H) 450mm, the material of the top shall be plywood with VENEER 18mm thick. The table support to be made of teak wood of size- 55x22mm. Center Table Leg to be made of teak wood of size - 50x50mm & should be polished. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing,Fixing of Pin Board: Size: 900(L) x 600 (W) mm. Pin Board- 12mm thick soft board with fabric duly ironed and pasted on the exposed side and double folded on the edge duly stapled. Satin-finish aluminium frame matches any classroom environment and hanging system included. Framed in doubled sided curved anodized aluminum section Chromium plated and with plastic corners with good aesthetics. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Modular Table Type C in completely knock down conditions with an overall size 1800mm X 2000mm X 750mm that is to be assembled at site. The worktop shall have the size 1800mm X 800mm. Top made up of 25 mm thick pre laminate MDF board and edge duly sealed with 2mm thick PVC Beading. The Side and modesty is made of 18mm thick pre laminate MDF board. All edge sealed with 2mm thick PVC beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The modesty panel shall be connected with both end. Glides crews is provided at the bottom of the legs for Level adjustment. The table top shall have flapper for easy wire management for houses video, audio, data and power connection discretely. The table top shall be supported on CRCA powder coated rectangle pipe having cross-section area 40mm X 20mm with 1.6mm thick. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. . The three drawer unit size- 650(H)x400(W)x400(D). Mobile pedestals is placed below top. Mobile pedestals made of 18mm thick Pre laminated MDF board. The sides of drawers and facia made of 18mm thick pre laminated MDF Board. Back of the pedestal made of 9mm Pre laminated MDF Board. Pedestal stand-alone and not supported to the table top. Pedestals have 3 drawer 2 for personal and 1 for lateral files. Drawers are provided with single extension telescopic ball bearing slide channels. Pedestal is provided with single central locking system, SS handles and four number poly-propylene castors is provided with the pedestal. A side storage unit with an overall size 1200mm X 450mm X 650mm shall be provided along with the table. Top should be made from 25mm thick Pre Laminated MDF Board. All work surface edges are duly sealed with 2mm thick PVC Edge banding. All profile i.e. side, back, top, shutter, shelf, skirting shall be made from 18mm thick Pre Laminated MDF Board. All work surface edges are duly sealed with 2mm thick PVC Edge banding. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function.. It shall have 2 sliding shutter which slides over sliding rail track. The shutter shall be operated by SS handle. There shall be buffers provided at the bottom to avoid scratches on the floor. Lock, Hinges, Telescopic channels shall be of make Hettich / Ebco / Ozone or equivalent. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and supplying Medium Back Revolving Chair with ergonomic design, comfortable & aesthetically appealing. The back & seat is made up of 1.2 cm. thick hot pressed plywood upholstered with fabric and moulded Polyurethane Foam. The back foam is designed with contoured lumber support for extra comfort. Back Size: 48.0cm.(W) X 63.0cm.(H) SEAT SIZE: 48.0cm.(W) X 49.0cm.(D).The polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20+/-2 for 25% compression. SEAT-BACK CONNECTING SPINE: The seat and back are arrested together with a 6.5cm (w) spine made of 0.8cm thick. HR steel. The spine is black powder-coated. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. ARMREST ASSY: Armrest shall be in injection moulded PP arm. The mechanism of chair shall have following features: The synchro tilt mechanism shall be designed as-360° revolving type, 17° ±2° maximum tilt on pivot at center, Upright position locking, Tilt tension adjustment. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The bellow is 3 piece telescopic type and injection molded in black polypropylene. The pedestal is injection molded in black 30% glass filled Nylon. A 10.5 dia forged bright zine plated M.S. caster pin shall be press-fitted into each prong for holding the castors. The pedestal shall be 700 mm pitch centre dia. (750 mm with castors). The twin wheel casters are made of nylon . Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min 94.0 to max 104.0 cm. Seat height - min 46.0cm to max 56.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Visitor Chair: SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 cm thick hot pressed plywood, upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam is designed with contoured lumbar support for extra comfort. Mid back Chair BACK SIZE 48.0cm. (W) x 47.0cm. (H) SEAT SIZE: 45.0cm. (W) x 48.0cm. (D) POLYURETHANE FOAM: The polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 on Hampden machine at 25% compression. ARMRESTS: The one-piece armrests made of black integral skin polyurethane with 50-70 Shore ‘A’ Hardness and reinforced with M.S. insert. The armrests are scratch and weather resistant. The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 0.6cm thick. HR steel. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. TUBULAR FRAME: The tubular frame is cantilever type & made of Dia. 25.4mm x 2mm thick M.S. E.R.W. tube. Bending of Tube Should be done on CNC operated machine to ensure accuracy of bending of tube. Overall Dimensions of Chair shall be Seat Height -45.0cm. Height -81.5cm, Width & Depth of Chair as measured from pedestal - Width-55.0 cm and Depth-63.0 cm. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and supplying executive table with an overall size -1200mm L X 750mm W X 750mm H. The top and modesty panel shall be made from 18mm thick Pre-Laminated MDF Board. All edges are duly sealed with 2mm thick PVC Edge banding. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Understructure: The top shall be supported on C frame made from CRCA sheet of 0.9mm thick. Rectangular Frame shall be Fabricated component in 1.2mm thick CRCA. Leg should be made from 38mmx25mmx1.2mm thick MS ERW Tube. Wire management horizontal and vertical wire carrier shall be made from 0.8mm thick CRCA sheet. There shall be leveller provided at the bottom made of Nylon. Three drawer pedestal: Shell, drawer tray, Drawer Front, Frame Assembly made of 0.8mm thick CRCA sheet. It should be operated on channel and recessed plastic handle with centralized locking mechanism. Lock shall be of 10 lever cam Lock. Snap fit ABS plastic handle shall be built in plastic. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Meeing Table Oval Shape in completely knock down conditions with an overall size 3600mm X 1200mm X 750mm that is to be assembled at site. Top made up of 25 mm thick pre laminate MDF board and edge duly sealed with 2mm thick PVC Beading. The Side and modesty is made of 18mm thick pre laminate MDF board. All edge sealed with 2mm thick PVC beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The modesty panel shall be connected with both end. Glides crews is provided at the bottom of the legs for Level adjustment. The table top shall have flapper for easy wire management for houses video, audio, data and power connection discretely. Wire management horizontal and vertical wire carrier shall be made from 0.8mm thick CRCA sheet. Raceway shall be provided of MS CRC sheet below the work top as per requirement for inlaying of electrical management and carrying the wire horizontally. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. The table shall be supported over SS pipe leg of 202 grade. It shall have cross-section area 80mm X 20mm. There shall be buffers provided to avoid scratches on the floor. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supply and placing of personal lockers having an Overall size of Personal Locker Unit: 380mm(W) X 450mm(D) X 1800mm(H) having 4 locker unit. Each locker is providing with a locking facility achieved by 10 lever cam lock with lock lever. Construction & Material: CRCA Sheet of 0.8mm thick. Shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg maximum. Total rigid knockdown construction. Aesthetically appealing snap fit ABS plastic handle and plastic label holder for identification. Ventilation attractive punched pattern for ventilation. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supply and placing Medium Back Revolving Chair Type A+: The back & seat is made up of 1.2 cm. thick hot pressed plywood upholstered with leatherette and moulded Polyurethane Foam. The back foam is designed with contoured lumber support for extra comfort. Back Size: 54.0cm.(W) X 73.0cm.(H) SEAT SIZE: 54.0cm.(W) X 49.0cm.(D).The polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20+/-2 for 25% compression. SEAT-BACK CONNECTING SPINE: The seat and back are arrested together with a 9.0cm (w) spine made of 0.8cm thick. HR steel. The spine is black powder-coated. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. ARMREST ASSY: The armrest assy. comprises of three parts viz. the armrest support tube and P.U. armrest and the armrest top. The armrest tube assy. is made of 2.54cm(1") x 16 BG. M.S. E.R.W. support tubes and Chrome plated. The P.U. armrest is made of black integral skin polyurethane with 50-70 shore 'A' Hardness and reinforced with M.S. insert. The armrest top is made of ABC & upholstered with foam & leather. The mechanism of the chair shall have following features : 360⁰ revolving type, Knee Tilt system, 5-position locking with antilock back mechanism. Tilt tension adjustment and position locking with anti-shock back mechanism, which prevents the backrest from impacting the user when the lock is released. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished aluminum it shall be fitted with 5 nos. twin wheel castor. The size of the pedestal shall be 62.0 +/- 1.0 cm pitch-centre-dia (70.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black nylon. Overall dimensions of Chair shall be, Width of Chair - 70.0cm, Depth of Chair - 70.0 cm as measured from pedestal below with castor. Height from ground - min 107.0 to max 117.0 cm. Seat height - min 46.0cm to max 56.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

DOCUMENTATION SYSTEM / COMPATOR: Providing and placing Optimizer As per Layout (4 Way fixed stick-1 and 4 Way Last stick-1 and 4 Way face to face - 6). Overall Dimensions of Single Static Drive Unit (U/C + Fittings + Cover) shall be 915mm(W)x457mm(D)x2080mm(H), Single Last Drive Unit (U/C + Fittings + Cover) shall be 915mm(W)x457mm(D)x2080mm(H) and Twin Mobile Single Static Drive Unit (U/C + Fittings + Cover) shall be 915mm(W)x 914 mm(D)x2080mm(H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel. Each body shall have a main unit plus add on units (1,2,3,4). Shelf construction shall be made from CRCA steel 0.8 mm thick. Uniformly distributed load capacity of 80 Kg. Undercarriage shall have construction in welded frame made of HR sheet 3.15 mm thick. Cutting of Sheet Should be done on NC operated machine to ensure accuracy of cutting and bending of Sheet Should be done on CNC operated machine to ensure accuracy of bending. Finish shall be epoxy- polyester powder coat of approved color & shade. The Movements shall be Drive Type configuration: In case of D2 & D3 movement of units is achieved mechanically through a PU Drive Wheel and Sprocket -Chain-Tensioner arrangement mounted rigidly onto body size. For D3 each movable undercarriage shall be provided with 2 rollers on the shaft for driving, 2 antifriction ball bearing for rolling and 4 antifriction ball bearing for guiding between rail. Fittings shall be centralized locking arrangement through locking stiffener mounted onto back of single last unit so that it gets locked on channels when all the units are brought together. The Recess handle lock is placed at suitable height. This arrangement occupies a space of 90.0 mm. When the last unit is twin movable hinged doors are provided for the end bodies, so in this case locking stiffener is mounted onto drive unit cover and with tile fascia option it will be mounted in the recess vertical. Each Type have Knob near drive wheel manual of trim Drive units shall Locking the for locking of individual units when a person is using those units. Knob shall be rotated to unlock position when units are to be moved. End stoppers shall be provided to prevent derailment. Door locking shall be having hinged doors of recessed die cast handle cum lock giving 3 way locking through a lever & shooting bolts. Guide channels shall have 'J' section 2 mm thick HR & 25 mm Square bright bar. Fasteners shall be galvanized/blackodized/Zn plated. The label holder shall be made from 2 mm thick clear transparent acrylic sheet. Also total no. of loading levels per understructure shall be 15 for SD3. Fascia(tiling) 3 tile pattern fascia option on drive side panel plus 3 tile pattern fascia on non-drive side panel plus 3 tile pattern fascia option on back panel of single last plus 3 tile pattern fascia option on back panel of single static. The tiles are held together by stiffeners & fasteners in 2 vertical metal trims. Guide channels shall consist of 'J' section 2 mm thick & 25 mm square bright bar - both connected by screws. Prior to the embedding of the guide channels with the help of screw. . All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All as per the layout. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Table with Both side drawer,The product should be in complete knock down structure as much as possible/feasible enabling ease in transportation and assemblies within office. The table shall have 1365 (L) X 680 (w) X 750 (H). The work surface of the table shall be 18mm thick Pre Laminated MDF Board top with 2mm thick PVC edge beading on all sides. The under structure shall be C frame of 0.9mm thick powder coated CRCA MS. The tubular frame shall of Dia 25mm x 1.2mm thick MS ERU round tubes. It shall have one side 3 drawer unit & other side 2 drawer unit. Drawer unit shall be of size-355mm W X 559mm D X 430mm H, with shell of 0.6mm thick CRCA MS & drawer tray of 0.6mm thick CRCA MS & drawer front of 0.8mm thick CRCA MS & the drawer friction slide shall have 1.2 mm thick CRCA MS & lock shall be of 10 lever cam lock. Handles shall be built in plastic and with back cover made of plastic. All Fabricated parts which require welding are MIG / Spot welded. The Screw joining Wooden Panels to under structure are Chip Board Screws. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Table::- Table Size-2400(L)X1200(W)X750(H) mm. Top made up of 25 mm thick plain particle board clad with 0.6 mm thick post formed laminate and 06mm thick Backing Laminate-Flat edge duly sealed with 2mm thick PVC Beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Understructure of the table made up of 40x40mm SQR CRCA steel pipe with 1.6mm thickness. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing workstation table in completely knock down conditions with an overall size 1500mm X 600mm X 750mm that is to be assembled at site. The top shall be made from 25mm thick Pre-Laminated MDF Board. All edges are duly sealed with 2mm thick PVC Edge banding. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Understructure: The top shall be supported frame made from CRCA tube. Rectangular Frame shall be Fabricated component in 1.2mm thick CRCA tube . Leg should be made from 50mmx50mmx1.2mm thick MS CRCA Tube and the connecting beam of the table shall have a cross section of 40mmx40mmx1.2mm thick MS CRCA Tube. The connectors for the legs and beams shall be made of die casted aluminium and powder coated. Wire management horizontal and vertical wire carrier shall be made from 0.8mm thick CRCA sheet. There shall be leveller provided at the bottom made of Nylon. The workstation shall have a metal keyboard tray and CPU trolley. Raceway shall be provided of MS CRC sheet below the work top as per requirement for inlaying of electrical management and carrying the wire horizontally. The table top shall have 400mm long flapper for easy wire management. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All as per the layout. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Printer table in completely knock down conditions with an overall size 600mm X 600mm X 750mm that is to be assembled at site. The worktop shall have the size 600mm X 600mm. Top made up of 18 mm thick pre laminate MDF board and edge duly sealed with 2mm thick PVC Beading. The Side & modesty is made of 18mm thick pre laminate MDF board. All edge sealed with 2mm thick PVC beading. The self is made of 18mm thick pre laminate MDF board. All edge sealed with 2mm thick PVC beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Glides crews is provided at the bottom of the legs for Level adjustment. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and supplying of Dual desk cum Seat (Writing Pad Folding) (Width 1050mm) for step type classroom. First Module: The Complete MS section to be powder coated in approved based high gloss colour. Vertical supporting pipe is to be made of 80x30 mm elliptical shape pipe with 2.0 mm wall thickness to be connected with 50x50x1.6mm horizontal supporting pipe and 1.2mm thick modesty. The Modesty panels made of 1.2 mm thick CRCA sheet with perforation of dia 3mm on the sheet shall be uniform except 100mm four side border. Perforated curved modesty with both side of vertical pipes. 20x20x1.6mm square pipe to be used for strengthening the border of modesty. The entire MS sheet cutting should have through NC sheet metal cutting machine, the entire sheet metal banding should have through CNC sheet metal bending machine & the entire MS sheet perforation should have through metal perforated machine. BASKET : Basket shall be Made of 6mm thick Mild steel rod making a curved basket connected with the 50x50 mm square pipe support. FIXING: Fixing at site to be done with metal dash fasteners of 100x12 mm size grouted with chemical filter compound . Pedestal made of 2mm thick pressed HR steel base and shall be ribbed with 2 counters sunk holes for floor fixing. The front row have full MS modesty panel. Desk Top made up of 25 mm thick pre laminate particle board - edge duly sealed with 2mm thick PVC Beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. 25x3mm MS angle shall be used for top supporting. The complete steel structure shall be constructed by welding and welding part should be done by Robotic MIC welding. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. Size: Desk height- 750mm +/- 10mm, Top Size - 1200mm(W)x420mm(D) +/- 10mm. Middle Module: The Complete MS section to be powder coated in approved based high gloss colour. Vertical supporting pipe is to be made of 80x30 mm elliptical shape pipe with 2.0 mm wall thickness to be connected with 50x50x1.6mm horizontal supporting pipe and 1.2mm thick modesty. The Modesty panels made of 1.2 mm thick CRCA sheet with perforation of dia 3mm on the sheet shall be uniform except 100mm four side border. Perforated curved modesty with both side of vertical pipes. 20x20x1.6mm square pipe to be used for strengthening the border of modesty. The entire MS sheet cutting should have through NC sheet metal cutting machine, the entire sheet metal banding should have through CNC sheet metal bending machine & the entire MS sheet perforation should have through metal perforated machine. BASKET : Basket shall be Made of 6mm thick Mild steel rod making a curved basket connected with the 50x50 mm square pipe support. FIXING: Fixing at site to be done with metal dash fasteners of 100x12 mm size grouted with chemical filter compound . Pedestal made of 2mm thick pressed HR steel base and shall be ribbed with 2 counters sunk holes for floor fixing. Seat: Seat has self closing mechanism which will operate by means of dead weight. Seat understructure is made from combination of welded fabricated structure of 2mm Thick HR sheet and 8mm thick ply with moulded PU Foam of Density 45kg/cu.mtr. on top which is covered with stitched upholstery made of leatherite. Seat back is made from combination of 8mm thick ply with moulded foam on top which is covered with stitched upholstery made of leatherite. Desk Top made up of 25 mm thick pre laminate particle board - edge duly sealed with 2mm thick PVC Beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. 25x3mm MS angle shall be used for top supporting. The complete steel structure shall be constructed by welding and welding part should be done by Robotic MIC welding. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. Size: Desk height- 750mm +/- 10mm, Top Size -1200mm(W)x420mm(D) +/- 10mm, Seat Size- 450mm(W)x420mm(D) +/-10mm, Seat height – 450mm+/- 10mm. Last Module: The Complete MS section to be powder coated in approved based high gloss colour. Vertical supporting pipe is to be made of 80x30 mm elliptical shape pipe with 2.0 mm wall thickness to be connected with 50x50x1.6mm horizontal supporting pipe and 1.2mm thick modesty. The Modesty panels made of 1.2 mm thick CRCA sheet with perforation of dia 3mm on the sheet shall be uniform except 100mm four side border. Perforated curved modesty with both side of vertical pipes. 20x20x1.6mm square pipe to be used for strengthening the border of modesty. The entire MS sheet cutting should have through NC sheet metal cutting machine, the entire sheet metal banding should have through CNC sheet metal bending machine & the entire MS sheet perforation should have through metal perforated machine. BASKET : Basket shall be Made of 6mm thick Mild steel rod making a curved basket connected with the 50x50 mm square pipe support. FIXING: Fixing at site to be done with metal dash fasteners of 100x12 mm size grouted with chemical filter compound . Pedestal made of 2mm thick pressed HR steel base and shall be ribbed with 2 counters sunk holes for floor fixing. Seat: Seat has self closing mechanism which will operate by means of dead weight. Seat understructure is made from combination of welded fabricated structure of 2mm Thick HR sheet and 8mm thick ply with moulded PU Foam of Density 45kg/cu.mtr. on top which is covered with stitched upholstery made of leatherite. Seat back is made from combination of 8mm thick ply with moulded foam on top which is covered with stitched upholstery made of leatherite. The complete steel structure shall be constructed by welding and welding part should be done by Robotic MIC welding. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. Seat Size- 450mm(W)x420mm(D) +/-10mm,Seat height – 450mm+/- 10mm.All as per the layout. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & placing Podium with an overall size 750x550x1100mm (LXWXH). Top & side, back, shelves and all other are made from 18mm thick Pre Laminated MDF Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The podium shall have 1 nos. of self shall be provided with single extension telescopic ball bearing slide channels. There shall be buffers provided at the bottom to avoid scratches on the floor. The skirting shall be provided at bottom. The front of podium will be used for engraving the name of respective department, which will be told to the L1 bidder. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Stage Table For 7 Seating in completely knock down conditions with an overall size 4800mm X 900mm X 750mm that is to be assembled at site. The worktop shall have the size 4800mm X 900mm. Top made up of 30 mm thick pre laminate MDF board and edge duly sealed with 2mm thick PVC Beading. The Side is made of 25mm thick pre laminate MDF board. All edge sealed with 2mm thick PVC beading. The modesty pannel is made of 18mm thick pre laminate MDF board. All edge sealed with 2mm thick PVC beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The modesty panel shall be connected with both end. Glides crews is provided at the bottom of the legs for Level adjustment. The table top shall have flapper for easy wire management for houses video, audio, data and power connection discretely. The table top shall be supported on CRCA powder coated rectangle pipe having cross-section area 40mm X 20mm with 1.6mm thick fit for stability of top. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and placing of Executive visitor chair: The seat is made up of 1.2 cm. thick hot pressed plywood upholstered with leatherette and moulded Polyurethane Foam. The back foam is designed with contoured lumbar support for extra comfort. BACK SIZE 49.0cm. (W) x 53.0cm. (H) SEAT SIZE: 50.0cm. (W) x 50.0cm. (D) POLYURETHANE FOAM: The polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 on Hampden machine at 25% compression. SEAT-BACK CONNECTING SPINE: The seat and back are arrested together with a 9.0cm (w) spine made of 0.8cm thick. HR steel. The spine is black powder-coated. The tubular frame shall be cantilever type & made of 40x20x2 mm thick capsule tube. Bending of Tube Should be done on CNC operated machine to ensure accuracy of bending of tube. Overall Dimensions of Chair shall be Seat Height -46.0cm. Height -97.0cm, Width & Depth of Chair as measured from pedestal - Width-54.0 cm and Depth-68.0 cm. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and placing of Table .The table shall have 1350 (L) X 600 (W) X 750 (H). The work surface of the table shall be 25mm thick Pre Laminated MDF Board top with 2mm thick PVC edge beading on all sides. Modesty panel made of 0.8mm thick CRCA MS sheet. Leg shall be made from 1.6mm thick CRCA MS. Legs with 3mm thick MS plate at bottom. The base support is having provision for wire entry and glide fixing. The wire carrying is facilitated through the hollow space between two leg. Table top support shall be made of 2mm thick MS sheet provided for overall product stability. Glides crews is provided at the bottom of the legs for Level adjustment. Grommets (cut outs) is provided on table top for cabling. Grommets is provided with PVC cover. There shall be Wire Management wire carrier shall be made from 0.6 mm thick CRCA. All Fabricated parts which require welding are MIG welded. The Screw joining Wooden Panels to under structure are Chip Board Screws. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing, supplying and placing Glass door steel almirah Dimension: Overall size of Almirah (Excluding Leveler): Height: 1981 mm x Width: 916 mm x Depth: 486 mm. Construction & Material: CRCA Sheet for shelf & anodized screws. Welded construction.0.8 thickness High yield strength CRCA for doors and back. 0.9 thickness for all other components. Locking & Handle: Brass handle, Two way locking mechanism with shooting bolt. Maximum uniformly distributed load capacity per each full shelf is at least 40kg. 4 Nos. of adjustable shelf mounting. It should be supplied with 4 nos. of adjustable shelves i.e. 5 loading compartments. Leveller: M10 screw type leveller with hex plastic base. Glass shall be 4mm thick. The complete steel structure shall be constructed by welding and welding part should be done by Robotic MIC welding. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing L-Shape Lab Table.The product should be in complete knock down structure as much as possible/feasible enabling ease in transportation and assemblies within office. The L- shape lab table shall have size- 1800 (L) x 1200(L) X 680 (d) X 750 (H). 18-20mm thick Granite work top placed on neoprene rubber sheet on the top of table frame work. Deep Drawn moulded 'C' Frame Legs of minimum 2.5mm thickness CRCA MS. The under structure shall be 0.8mm thick powder coated CRCA MS. It shall have two 4 drawer unit & other 5 shutter unit. Drawer unit & shutter unit shall of 0.8mm thick CRCA MS. Handles shall be built in plastic. All Fabricated parts which require welding are MIG / Spot welded. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. Mini Vertical service channel connector enabling concealed wire management from below the table to the electrical service channel. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Face to Face Work station table in completely knock down conditions with an overall size 1200mm X 1200mm X 750/1200mm (LxWxH) (Screen upto 1200) that is to be assembled at site. The top shall be made from 25mm thick Pre-Laminated MDF Board. All edges are duly sealed with 2mm thick PVC Edge banding. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Understructure: The top shall be supported frame made from CRCA tube. Rectangular Frame shall be Fabricated component in 1.2mm thick CRCA tube . Leg should be made from 50mmx50mmx1.2mm thick MS CRCA Tube and the connecting beam of the table shall have a cross section of 40mmx40mmx1.2mm thick MS CRCA Tube. The connectors for the legs and beams shall be made of die casted aluminium and powder coated. There shall be leveller provided at the bottom made of Nylon. The workstation shall have a metal keyboard tray and CPU trolley. Raceway shall be provided of aluminium extrution below the work top as per requirement for inlaying of electrical management and carrying the wire horizontally. The table top shall have 400mm long flapper for easy wire management. A middle partition having pin board/ writing board shall be provided. The middle partition shall be made of aluminium extrution having thickness of 30mm thickness. The three drawer unit size- 650(H)x400(W)x400(D). Mobile pedestals is placed below top. Mobile pedestals made of 18mm thick Pre laminated MDF board. The sides of drawers and facia made of 18mm thick pre laminated MDF Board. Back of the pedestal made of 9mm Pre laminated MDF Board. Pedestal stand-alone and not supported to the table top. Pedestals have 3 drawer 2 for personal and 1 for lateral files. Drawers are provided with single extension telescopic ball bearing slide channels. Pedestal is provided with single central locking system, SS handles and four number poly-propylene castors is provided with the pedestal. The aluminium parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All as per the layout. Lock, Hinges, Telescopic channels shall be of make Hettich / Ebco / Ozone or equivalent. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Library Chair : Seat made of 12mm thick hot pressed plywood with moulded polyurethane foam 40mm thick having density 45kg/m³ upholstered with fabric. Back made of 12mm thick hot pressed plywood with moulded polyurethane foam 25mm thick having density 45kg/m³ upholstered with fabric. The seat and back shall be arrested together with the armrest. The frame structure shall be supported by four legs made up of MS/CRCA chrome plated pipe of size Dia 25mm with 1.2mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 465±10 mm(D) X 500±10 mm(W) and back size shall be 460±10 mm(W) X 360±10 mm(H) from seat. Overall height shall be 790±10 mm, overall depth 560±10 mm & overall width 550±10mm. Bending of Tube Should be done on CNC operated machine to ensure accuracy of bending of tube. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Face To Face Open Rack: The product should be in complete knock down condition as much as possible/ feasible enabling ease in transportation and assemblies within premises. Product Size: Width 900mm, Height: 1850mm, Depth: 600mm. Construction: Rigid Knockdown construction. Material: CRCA 0.8mm thick for shelf, sides & back. 0.8mm thick CRCA for all other components. Number of Adjustable shelf: Five adjustable shelves. Uniformly Distributed Load Capacity per each shelf is 30 Kg maximum. Label holder & range Indicator: Label Holder & Range indicator on each main unit for inserting labels. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Reception table in completely knock down conditions with an overall size 1800mm X 820mm X 1000mm (LXWXH) that is to be assembled at site. The top shall be made from 25mm thick Pre-Laminated MDF Board. All edges are duly sealed with 2mm thick PVC Edge banding. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The top shall be supported frame made from CRCA tube. Rectangular Frame shall be Fabricated component in 1.2mm thick CRCA tube. Leg should be made from Dia 38mm x 1.2mm thick MS CRCA Tube. The Modesty & Side panels made of 0.8 mm thick CRCA sheet with perforation on the sheet shall be uniform of 3mm dimension except 100mm four side border. All Fabricated parts which require welding are MIG. The table shall have upper top shelf made from 25mm thick Pre-Laminated MDF Board. All edges are duly sealed with 2mm thick PVC Edge banding. The Screw joining Wooden Panels to under structure are Chip Board Screws. Glides crews is provided at the bottom of the legs for Level adjustment. Grommets (cut outs) is provided on table top for cabling. Grommets is provided with PVC cover. There shall be Wire Management wire carrier shall be made from 0.6 mm thick CRCA. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. The three drawer unit size- 650(H)x400(W)x400(D). Mobile pedestals is placed below top. Mobile pedestals made of 18mm thick Pre laminated Particle board. The sides of drawers and facia made of 18mm thick pre laminated Particle Board. Back of the pedestal made of 9mm Pre laminated Particle Board. Pedestal stand-alone and not supported to the table top. Pedestals have 3 drawer 2 for personal and 1 for lateral files. Drawers are provided with single extension telescopic ball bearing slide channels. Pedestal is provided with single central locking system, SS handles and four number poly-propylene castors is provided with the pedestal. Lock, Hinges, Telescopic channels shall be of make Hettich / Ebco / Ozone or equivalent. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Computer Table: Overall size-1200(L)X600(W)X750(h) in mm. Table top made up of 18 mm pre-laminated particle board and all edge sealed with 2mm thick PVC beading. The Side and modesty is made up of 18 mm pre-laminated particle board and all edge sealed with 2mm thick PVC beading. All profile i.e. 1 drawer on one side, Keyboard tray & space for files / CPU are made of 18 mm pre-laminated particle board and all edge sealed with 2mm thick PVC beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Glides crews is provided at the bottom of the legs for Level adjustment. Lock, Hinges, Telescopic channels shall be of make Hettich / Ebco / Ozone or equivalent. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and fixing of Face to Face work Station System Size 1200x1200x750/1200 (LxWxH) :- One seater overall size-1200(L) x 1200(W) x Height of panel 1200 mm. Side panel and main panel shall be of 60mm. The 60mm panel comprises of 2 nos. Of vertical trims made of aluminum extrusions and Horizontal trims shall be made of aluminum extrusions at every division of tile/block. Block for 60mm panel’s thickness shall comprises of 38mm thick paper honeycomb + 9mm particle board on each sides + 0.6mm decorative laminate or fabric on both sides. The fabric shall be upholstered with particle board framing shall used on outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. Blocks shall be located in the mid segment of the panels and shall be provided with cut outs for mounting switch boxes (above the worktops). Fabricated bottom frame for 60mm panel comprises of L channels made of 2mm thick CRCA steel formed plates of 3mm thick HR steel & ERW steel tube of size 35x15x1.6mm thick in oval cross section welded together. This frame shall be bolted to the uprights with M6 screws. Top tiles shall be slid in to the panels from top before fixing the top horizontal. The top shall have white board / glass/ laminate tiles of approved shade. Laminated tiles shall be 9.0 mm thick pre-laminated particle board having all its edges with minimum 0.5 mm thick PVC edge banding. White board tiles shall be made of 8.0 mm thick particle board laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and having all its edges with minimum 0.5 mm thick PVC edge banding. Glass tiles - 4 mm thick toughened clear glass. Split Top shall be provided for two different finishes in single panels. Bottom tiles shall be press fitted on to the assembly frame of the panel with the help of snap on clips made of nylon and support clips made from PP co polymer. Bottom tiles shall be of Metal tiles made of 0.8mm thick CRC sheet. These uprights and horizontals are made of aluminum extrusion having material & have average wall thickness of 1 mm. The panels shall be joined to each other directly with joinery or with the help of post to form. Free standing modules shall be provided with stability bracket. The top trims and end trims for 60 mm shall be made from aluminum extrusion having material. All kinds of extrusions for 60 mm shall have average wall thickness of 1 mm. Top trim shall be press fitted on the horizontal extrusion. Die cast. aluminum alloy shall be provided according to the joineries. The worktop is made of 25mm thick pre laminated particle board with 2mm thick PVC edges bands all around all the edges are pressed with 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The work surface shall be provided with circular cut out of Dia.65mm for passing of wires. These cut outs shall be provided with ABS covers. Table top height – 750mm (including table top thickness of 25mm) Work surface bracket shall be mounted on to the Horizontal extrusion. 4 numbers of ribs are provided in the work surface for strengthening purpose. All the work surface shall be mounted on the work surface through round Philip head diameter 4 mm x 19 length having finish zinc plated. The panel legs shall provide to support panels. Panel legs shall fabricated by CO2 welding MS Tube of section 38 mm x 25 mm ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm over which an M8 Leveler is fitted, which allows for adjustment of the height by 25mm. Double and single side leg assembly: shall be provided to supporting panels & work surface. Wire carrier shall be made from 0.8 mm thick CRCA sheet. It shall be constructed with two parts, one shall be body & another shall be cover. It holds the cables & gives aesthetic appearance by covering all cables. Worktop supporting pedestal shall be provided having provision to fit with worktop and pedestal leg welded assembly fitted at the bottom. Key board tray made of 1.2mm thick CRCA steel. Adjustable wheel mounted CPU trolley made of 1 mm thick CRCA steel. Pedestal, key board tray & CPU Trolley shall be provided with each workstation. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. The three drawer unit size- 680(H)x400(W)x450(D). Mobile pedestals is placed below table top. Mobile pedestals made of 18mm thick Pre laminated MDF board. The sides of drawers and facia made of 18mm thick pre laminated MDF Board. Back of the pedestal made of 9mm Pre laminated MDF Board. Pedestal stand-alone and not supported to the table top. Pedestals have 3 drawer 2 for personal and 1 for lateral files. Drawers are provided with single extension telescopic ball bearing slide channels. Pedestal is provided with single central locking system, SS handles. All as per the layout. Lock, Hinges, Telescopic channels shall be of make Hettich / Ebco / Ozone or equivalent. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Conference Table 10 Seating in completely knock down conditions with an overall size 3400mm X 1200mm X 750mm (LXWXH) that is to be assembled at site. Top made up of 25 mm thick pre laminate MDF board and edge duly sealed with 2mm thick PVC Beading. The Side and modesty is made of 18mm thick pre laminate MDF board. All edge sealed with 2mm thick PVC beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The modesty panel shall be connected with both end. Glides crews is provided at the bottom of the legs for Level adjustment. The table top shall have flapper for easy wire management for houses video, audio, data and power connection discretely. Wire management horizontal and vertical wire carrier shall be made from 0.8mm thick CRCA sheet. Raceway shall be provided of MS CRC sheet below the work top as per requirement for inlaying of electrical management and carrying the wire horizontally. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. There shall be buffers provided to avoid scratches on the floor. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Supplying & Placing Conference Table 18 Seating: With Wire Manager size shall be Single seater :675 Width mm x 600 Depth mm , Two seater :1350 Width mm x 600 Depth mm and 750 height mm. The top made up of 25 mm thick pre laminate MDF board and edge duly sealed with 2mm thick PVC Beading. The Side and modesty is made of 18mm thick pre laminate MDF board. All edge sealed with 2mm thick PVC beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The modesty panel shall be connected with both end. Glides crews is provided at the bottom of the legs for Level adjustment. Grommets (cut outs) is provided on table top for cabling. Grommets is provided with PVC cover. There shall be Wire Management wire carrier shall be made from 0.6 mm thick CRCA powder coated and carrier cover shall be made of 12 mm thick thick pre laminate MDF board. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and supplying High Back Revolving Chair with ergonomic design, comfortable & aesthetically appealing. The back & seat is made up of 1.2 cm. thick hot pressed plywood upholstered with fabric and moulded Polyurethane Foam. The back foam is designed with contoured lumber support for extra comfort. Back Size: 48.0cm.(W) X 77.0cm.(H) SEAT SIZE: 48.0cm.(W) X 49.0cm.(D).The polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20+/-2 for 25% compression. SEAT-BACK CONNECTING SPINE: The seat and back are arrested together with a 6.5cm (w) spine made of 0.8cm thick. HR steel. The spine is black powder-coated. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. ARMREST ASSY: Armrest shall be in injection moulded PP arm. The mechanism of chair shall have following features: The synchro tilt mechanism shall be designed as-360° revolving type, 17° ±2° maximum tilt on pivot at center, Upright position locking, Tilt tension adjustment. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The bellow is 3 piece telescopic type and injection molded in black polypropylene. The pedestal is injection molded in black 30% glass filled Nylon. A 10.5 dia forged bright zine plated M.S. caster pin shall be press-fitted into each prong for holding the castors. The pedestal shall be 700 mm pitch centre dia. (750 mm with castors). The twin wheel casters are made of nylon . Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min 108.0 to max 118.0 cm. Seat height - min 46.0cm to max 56.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and supplying Locker : Product Size: Width 450mm, Height: 560mm, Depth: 450mm. Number of Adjustable shelf: one Lock 6 lever dual control guardian lock . Locker should be fully welded multi-bend body to ensure greater security. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and supplyingTable with 4 chair fix :The product should be in complete knock down structure as much as possible/feasible enabling ease in transportation and assemblies within office. The table shall have size: 1180(L) X 1580(W) X 750(H). The top surface of the table shall be made of 1.2mm thick SS 304 grade sheet. Rectangular Frame should be Fabricated component in 1.2mm thick CRCA. Leg should be Fabricated component in 40mmx40mmx1.2mm thick MS ERW Tube. Chair: The seat & back shell of chair be in injection moulded polypropylene. Rectangular Frame should be Fabricated component in 1.2mm thick CRCA. Leg should be Fabricated component in 40mmx40mmx1.2mm thick MS ERW Tube. All Fabricated parts which require welding are MIG welded. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. Provision for levellers should be given for adjusting height if required. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and supplying Computer Chair: seat & back made of 12mm thick hot pressed plywood, with fabric and moulded polyurethane foam with PVC lipping all around. The back foam is designed with contoured lumber support for extra comfort. Back foam size: 440(W) x 420(H) mm & seat foam size: 440(W)x 420(D) mm. The one piece armrest made of black integral skin polyurethane with 50-70 shore ‘A’ hardness and reinforced with M.S. insert. The armrests are scratch and weather resistant. The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 0.6cm thick. HR steel. The push back tilt mechanism shall be designed as-360° revolving type, 17° ±2° maximum tilt on pivot at center,Upright position locking, Tilt tension adjustment. The pneumatic height adjustment shall have an adjustment stroke of 12.0 ±0.3cm. The Telescopic bellow assy:- The bellow is 3 piece telescopic type and injection molded in black polypropylene .The pedestal is injection molded in black 30% glass filled Nylon. A 10.5 dia forged bright zine plated M.S. caster pin shall be press-fitted into each prong for holding the castors. The pedestal shall be 700 mm pitch-centre- dia. (750 mm with castors). The twin wheel casters are made of nylon. . All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. Overall Dimensions of Chair shall be Seat Height – min 46.0 to max 58.cm, Height – min90.0 to max 102.0cm, Width & Depth of Chair as measured from pedestal - Width-75. cm and Depth-75.0cm. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and supplying Table with one side drawers The product should be in complete knock down structure as much as possible/feasible enabling ease in transportation and assemblies within office. The table shall have 1500(L) X 750(W) X 750(h). The work surface of the table shall be 25mm thick Pre Laminated MDF Board top with 2mm thick PVC edge beading on all sides. Side panel & Modesty Panel made from 18mm thick Pre Laminated MDF Board. All edges are duly sealed with 2mm thick PVC Edge banding. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The top under structure shall be C frame of 0.9mm thick powder coated CRCA MS. Rectangular Frame should be Fabricated component in 1.2mm thick CRCA. Leg should be Fabricated component in 32mmx32mmx1.2mm thick MS ERW Tube. It shall have one side 3 drawer unit. Drawer shell of 0.6mm thick CRCA MS & drawer tray of 0.6mm thick CRCA MS. The drawer body & front are made of 18mm thick Pre Laminated MDF Board. All edges are duly sealed with 2mm thick PVC Edge banding. The drawer friction slide shall have 1.2 mm thick CRCA MS & lock shall be of 10 lever cam lock. All Fabricated parts which require welding are MIG / Spot welded. The Screw joining Wooden Panels to under structure are Chip Board Screws. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Executive Table AG: The main desk is provided with the wire management system. The Main table shall be of size: 3600 Length mm x 2400 mm Width x 750 mm height. The worktop shall have the size 3600mm X 1200mm. Top surface of the table shall made up of 50mm (25+25) thick MDF board duly finished with 4mm thick Veneer and final coating of PU high gloss polish and 0.6mm thick Backing Laminate. The Main desk should contain in Smart Case - space slides effortlessly in style. Side panel made up of 36mm (18+18) thick MDF board duly finished with 4mm thick Veneer and final coating of PU high gloss polish. Modesty made up of 18mm thick MDF board duly finished with 4mm thick Veneer and final coating of PU high gloss polish. Main Desk should be provided with all necessary hardware & fittings etc. The mobile Pedestal shall be of size: 480 Width mm x 640 Depth mm x 600 Height mm. Mobile pedestal shall be made of 18mm thick MDF board duly finished with 4mm thick Veneer and final coating of PU high gloss. All non-exposed surface should be covered by 0.6mm thick white balancing laminate. Pedestals have 3 drawer 2 for personal and 1 for lateral files. Drawers are provided with single extension telescopic ball bearing slide channels. Pedestal is provided with single central locking system, SS handles. Side Unit Size-1200(W)X500(D)X750(H) mm. Top surface shall made up of 50mm (25+25) thick MDF board duly finished with 4mm thick Veneer and final coating of PU high gloss polish and 0.6mm thick Backing Laminate. Side panel made up of 18mm thick MDF board duly finished with 4mm thick Veneer and final coating of PU high gloss polish. Modesty made up of 18mm thick MDF board duly finished with 4mm thick Veneer and final coating of PU high gloss polish. All non-exposed surface should be covered by 0.6mm thick white balancing laminate. The shutter and shelves are made of 18mm thick MDF board duly finished with 4mm thick Veneer and final coating of PU high gloss polish. Side unit should be provided with all necessary hardware & fittings etc.. Lock, Hinges, Telescopic channels shall be of make Hettich / Ebco / Ozone or equivalent. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Back Unit Size- 2400(L)X450(W)X1800(H) mm. Top shall made up of 18mm thick MDF board duly finished with 4mm thick Veneer and final coating of PU high gloss polish and 0.6mm thick Backing Laminate. Side panel made up of 18mm thick MDF board duly finished with 4mm thick Veneer and final coating of PU high gloss polish. Modesty made up of 18mm thick MDF board duly finished with 4mm thick Veneer and final coating of PU high gloss polish. The shutter and shelves are made of 18mm thick MDF board duly finished with 4mm thick Veneer and final coating of PU high gloss polish. All non-exposed surface should be covered by 0.6mm thick white balancing laminate. Back unit should be provided with all necessary hardware & fittings etc. Lock, Hinges, Telescopic channels shall be of make Hettich / Ebco / Ozone or equivalent. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

High Back Revolving Chair AG: The back & seat is made up of 1.2 cm. thick hot pressed plywood upholstered with pure leather and moulded Polyurethane Foam. The back foam is designed with contoured lumber support for extra comfort. Back Size: 54.0cm.(W) X 76.0cm.(H) SEAT SIZE: 54.0cm.(W) X 49.0cm.(D).The polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20+/-2 for 25% compression. The backrest shall be made by keeping the natural curvature of the spine for lumbar support which helps to provide full back support. Seat and back shall be covered with polished wooden at both side for decorative appearance. The chair shall be supplied with wooden cushion arm having melamine polish. The seat and back are arrested together with a 65.0cm (w) spine made of 0.8cm thick. HR steel. The spine is black powder-coated. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. The mechanism of the chair shall have following features : 360⁰ revolving type, Knee Tilt system, 5-position locking with antilock back mechanism. Tilt tension adjustment and position locking with anti-shock back mechanism, which prevents the backrest from impacting the user when the lock is released. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of metal insert CRCA covered with natural wood it shall be fitted with 5 nos. twin wheel castor. The size of the pedestal shall be 62.0 +/- 1.0 cm pitch-centre-dia (70.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black nylon. Overall dimensions of Chair shall be, Width of Chair - 70.0cm, Depth of Chair - 70.0 cm as measured from pedestal below with castor. Seat height - min 46.0cm to max 56.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Medium Back Revolving Chair AG: The back & seat is made up of 1.2 cm. thick hot pressed plywood upholstered with pure leather and moulded Polyurethane Foam. The back foam is designed with contoured lumber support for extra comfort. Back Size: 54.0cm.(W) X 63.0cm.(H) SEAT SIZE: 54.0cm.(W) X 49.0cm.(D).The polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20+/-2 for 25% compression. The backrest shall be made by keeping the natural curvature of the spine for lumbar support which helps to provide full back support. Seat and back shall be covered with polished wooden at both side for decorative appearance. The chair shall be supplied with wooden cushion arm having melamine polish. The seat and back are arrested together with a 65.0cm (w) spine made of 0.8cm thick. HR steel. The spine is black powder-coated. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. The mechanism of the chair shall have following features : 360⁰ revolving type, Knee Tilt system, 5-position locking with antilock back mechanism. Tilt tension adjustment and position locking with anti-shock back mechanism, which prevents the backrest from impacting the user when the lock is released. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of metal insert CRCA covered with natural wood it shall be fitted with 5 nos. twin wheel castor. The size of the pedestal shall be 62.0 +/- 1.0 cm pitch-centre-dia (70.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black nylon. Overall dimensions of Chair shall be, Width of Chair - 70.0cm, Depth of Chair - 70.0 cm as measured from pedestal below with castor. Seat height - min 46.0cm to max 56.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Wooden Partition: The dimension of the table shall be (L) 2400 mm x (H) 1800mm, the material of the partition shall be teak wood. The horizontal & vertical support of the frame to be made of teak wood of size- 50x25mm. Wooden partition should be polished. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Sofa 3+1+1: Size of 1 seater sofa shall be 650(L) x 870(W) x 760(H)mm. Size of 3 seater sofa shall be 1750(L) x 870(W) x 760(H)mm. The frame material to be pinewood+ thickness of plywood used to be 12mm. The seat foam & back foam density to be 40kg/m3 upholstered with fabric. Sofa to be covered with good quality fabric. The material for leg to be teak wood and should be polish. The leg should be fixed with wood screw provided on frame in addition to M-8 / T-nut. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Conference Table 41 Seating : With Wire Manager size shall be Single seater :675 Width mm x 600 Depth mm , Two seater :1350 Width mm x 600 Depth mm and 750 height mm. Top surface of the table shall made up of 25mm thick MDF board duly finished with 4mm thick Veneer and final coating of PU high gloss polish and 0.6mm thick Backing Laminate. The Side and modesty is made of 18mm thick pre laminate MDF board. All edge sealed with 2mm thick PVC beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The modesty panel shall be connected with both end. Glides crews is provided at the bottom of the legs for Level adjustment. Grommets (cut outs) is provided on table top for cabling. Grommets is provided with PVC cover. There shall be Wire Management wire carrier shall be made from 0.6 mm thick CRCA powder coated and carrier cover shall be made of 12 mm thick thick pre laminate MDF board. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Conference Table 17 Seating : With Wire Manager size shall be Single seater :675 Width mm x 600 Depth mm , Two seater :1350 Width mm x 600 Depth mm and 750 height mm. The top made up of 25 mm thick pre laminate MDF board and edge duly sealed with 2mm thick PVC Beading. The Side and modesty is made of 18mm thick pre laminate MDF board. All edge sealed with 2mm thick PVC beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The modesty panel shall be connected with both end. Glides crews is provided at the bottom of the legs for Level adjustment. Grommets (cut outs) is provided on table top for cabling. Grommets is provided with PVC cover. There shall be Wire Management wire carrier shall be made from 0.6 mm thick CRCA powder coated and carrier cover shall be made of 12 mm thick thick pre laminate MDF board. The entire MS sheet cutting should have through NC sheet metal cutting machine and the entire sheet metal banding should have through CNC sheet metal bending machine. All the metal parts have free from the dent, burrs and sharp edges. Removing of grease, rust should be done before Powder coating. The metal parts material is then oven baked with a controlled temperature of 180 deg. C to 200 Deg. minimum thickness of powder coated should be 40-50 microns. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.

Providing and supplying high back chair with ergonomic design, comfortable & aesthetically appealing. Seat : (W)51.0cm x (D) 52.5cm. Seat made of 12mm thick hot pressed plywood with moulded polyurethane foam 50mm thick having density 40kg/m³ upholstered with mesh fabric. Size of back shall be (W)-48.5cm x (H)-62.0cm. The back shall made up of two piece injection moulded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main assembly. Armrest shall be in injection moulded PP arm. The mechanism of chair shall have following features: The center tilt mechanism shall be designed as-360° revolving type, 17° ±2° maximum tilt on pivot at center, Upright position locking, Tilt tension adjustment. Spine bracket shall made of Aluminium die cast piece connecting back with mechanism. The neck rest assembly is mounted on the top of back it can be adjusted up to 4.5+/- 0.5cm up-down and has regular adjustment of 30 degree +/-2 . The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The bellow is 3 piece telescopic type and injection molded in black polypropylene. The pedestal is injection molded in black 30% glass filled Nylon. A 10.5 dia forged bright zine plated M.S. caster pin shall be press-fitted into each prong for holding the castors. The pedestal shall be 700 mm pitch centre dia. (750 mm with castors). The twin wheel casters are made of nylon . Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min 116.0 to max 135.0 cm. Seat height - min 46.0cm to max 56.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. All work including Placing & fixing complete in all respect as per technical specification, as per approval & directions of Engineer In-charge.