Construction of 33 KV Line Gangnouli Baghpat

1. Safe carriage of Poles from Store Center to Site Store with loading & unloading at both ends respectively distance about 30 Km. (i) 9 Mtr. P.C.C. Poles

(ii) 11 M Long STP, SP-55 Round Pole

(iii) 13 M Long STP, SP-72 Round Pole

2. Loading, Safe carriage & unloading of heavy stock material (other than pole) from store center to site store with proper stacking of material distance about 30 Km.

3 (A) Excavation of foundation pit in mix soil/normal soil/soft & hard rock and its back filling and leveling etc. The size of the pit will be (900×600)mm and having depth of 1/6th of the full length of the support & Erection of support. The work includes carriage and handling of supports from site store to pit site. (i) 9 Mtr. P.C.C. Poles

(ii) 11 M Long STP, SP-55 Round Pole

(iii) 13 M Long STP, SP-72 Round Pole

3 (B) Fixing of all clamps, Cross Bracing Sets 3.5 Mtr. from M.S. Angle 65×65×6mm/50×50×6mm & other accessories on the supports as per drawing. Work includes cutting of holes and providing M.S. Bolts of 16×40mm size in the middle of cross bracing with 1 no. spring washer. The work also includes carriage & handling of accessories from sectional store to pit site as well as any fabrication work if required. (i) Single Pole (a) 9 Mtr. P.C.C. Poles

(b) 11 M Long STP, SP-55 Round Pole

(c) 13 M Long STP, SP-72 Round Pole

(ii) Double Pole Structures (a) 9 Mtr. P.C.C. Poles

(b) 11 M Long STP, SP-55 Round Pole

(c) 13 M Long STP, SP-72 Round Pole

(iii) Tri Pole Structures (a) 11 M Long STP, SP-55 Round Pole

(iv) Four Pole Structures (a) 9 Mtr. P.C.C. Poles

(b) 11 M Long STP, SP-55 Round Pole

(v) Stud Pole Supports on (a) 9 Mtr. P.C.C. Poles

4. Grouting of supports in CC 1:4:8 (Cement, sand & 40 mm brick ballast) Grouting will be done in the block of size (450×450)mm ×1/6th of full length of the support, up to ground level, 300 mm plinth above the ground level with C.C. 1:3:6 (Cement, Course sand and Stone grit) with muffing as per drawing, work includes back filling and proper ramming. (i) 9 Mtr. P.C.C. Poles

(ii) 11 M Long STP, SP-55 Round Pole

(iii) 13 M Long STP, SP-72 Round Pole

5. Grouting of stay rods (20×1800)mm including all work of excavation, cement concrete in size (0.60 × 0.60 × 0.30)m in ratio 1:4:8 cement, sand, 40mm brick ballast) as per drg. including back filling, proper ramming etc and fixing tightening & nozzling of stay wire with stay rod with the poles of required tension as per drawing.

6. Earthing of supports with MS earth Rod of (20×2500)mm long including excavation of pit and driving M.S. Rod 3.0 M apart from support and 0.5m below the ground level and connecting below the earth electrodes with the help of G.I. wire no. 8 SWG and earthing lugs.

7. Laying, spreading, lifting and final sagging of 3 phases of ACSR Dog conductor in accordance with profile and sag chart including binding, Jumpering and fixing of P.G. Clamp as per requirement in 03 Nos. conductor in parallel.

8. Guarding between two poles like single poles, double poles, four poles, etc. to guard LT, 11 KV Line telephone and river crossing, road crossing etc. with G.I. wire no. 6 SWG and G.I. wire no. 8 SWG, including cutting with fabrication and fixing of guarding channel with clamps nut & bolts etc. as per drawing.

9. Providing & fixing of danger board at each location as per specification of the drawing with clamps etc.

10. Chopping of branches of trees of eucalyptus, Neem, Keekar and other kind of trees along the route of the line and disposal of the same at suitable place.

11. Painting of following supports/structures with 2 coats of synthetic enamel paint after one coat of ready mix primer including cost of all material, as well as rubbing/cleaning of surface as required for proper completion of work. Painting will be done by post office red paint from top to cross arm and remaining by Aluminium paint. a) All channels, X-Arms and Clamps of 9 Mtr. PCC Poles (i) Single supports

(ii) Double supports

(iii) Four Support

(iv) Stud Support

b) 11 Mtr, SP-55 Poles including all channels/X-Arms/Clamps etc. (i) Single supports

(ii) Double supports

(iii) Tri Support

(iv) Four Support

c) 13 Mtr, SP-72 Poles including all channels/X-Arms/Clamps etc. (i) Single supports

(ii) Double supports

12. Making H.T. Connections of the proposed line, on to the existing 33 KV bay/line from where line is eminating and another at the end of line to the terminal gantry at proposed 33 KV Sub-station. The work consists of fixing of tension fitting, insulators, jumpering, clamping and binding etc. at the end as per site conditions.

13. Wrapping of barbed wire on 33 KV PCC Poles/SP-55/SP-72 ST Poles as anti-climbing device for a length of 0.9 Mtr., wire pitch/gap 13mm and fixing upper and lower end keeping lower end at a height of 2.75 Mtr. from the ground complete with supply and fixing of lower end & upper end clamps made of M.S. Flat 40×5mm complete with nuts & bolts & all other required material.

14. Numbering of each supports by preparing background with dark yellow paint in the size of 150mm dia and writing support number 100mm high with black paint.

Krish Traders