Up keep and maintenance of Raj Niwas Annexe

Amount

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area beyond 3 sq. metres

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and laying hollow cement concrete block walling upto floor five level 200mm thick consisting of hollow block of size 400x200x200mm of mix 1:3:6(1 :cement 3 :coarse sand 6 :graded stone aggregate 10mm nominal and down size) having a crushing strength of 3.5N/sqmm at 28 days as per IS:2185 (part-I) 1979 laid in cement mortar 1:6(1 :cement 6 :coarse sand) upto floor five level.

Providing and laying hollow cement concrete block walling upto floor five level 100mm thick consisting of hollow block of size 400x100x200mm of mix 1:3:6(1 :cement 3 :coarse sand 6 :graded stone aggregate 10mm nominal and down size) having a crushing strength of 3.5N/sqmm at 28 days as per IS:2185 (part-I) 1979 laid in cement mortar 1:6(1 :cement 6 :coarse sand) upto floor five level.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

For thickness of tiles above 25 mm and up to 40 mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles of required size conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :

Thickness above 10 mm up to 25 mm

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion 11.1.1) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing 1st Class Padauk wood (Ornamental wood-Cat-I A )plain lining tongued and grooved, including wooden plugs complete with necessary screws (Frame work to be paid seperately) asper the archituctural drawing & as per the specified by Engineer-In-Charge.

25 mm thick panelling.

Providing and fixing Desinger wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws, and Melamine Polishing (PU) on exposed surface etc. complete 1st class Paduak wood (Cat-IA) as per the direction of Engineer-In-Charge.

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1) The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2) Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hours. 3) On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes.grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done and this surface is further allowed to dry for 12 hrs. 4) On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

1st Class Padauk wood (Cat-I A)

Providing and fixing 38mm thick fully pannel shutter for door, including panelling with 25mm thick having vertical grove patterns as per the architecture design and as directed by the Engineer-in-charge. (Hinges to be paid separately)

Ist class Paduak wood (Cat-IA)

Providing and fixing panelled or panelled and glazed shutters for doors,windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws,excluding panelling which will be paid for separately, all complete asper direction of Engineer-in-charge.

35 mm thick Ornamental Wood Cat-I (A) (Padauk)

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :

5 mm thick coloured toughened glass (Similar to Evolite-clear ET 135-II make Gobian or equalent)

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Providing and fixing in position shower enclosures (shower Cubicle) with fixtures model No K-704798IN-SHP Make Kohler or eaquvalent as per direction of Engineer In charge.

Providing and fixing mirror of 5 mm thick with paduak (Cat-IA) frame of size (1.50 x 1.27 m) width 35 mm and thickness 25 mm and 6 mm thick WPC backing and frames finished with PU polish and fixed in position with necessary screws etc. all complete.

Providing and fixing mirror of 5 mm thick with paduak (Cat-IA) frame of size (1.80 x 1.27 m) width 35 mm and thickness 25 mm and 6 mm thick WPC backing and frames finished with PU polish and fixed in position with necessary screws etc. all complete.

Providing and fixing towel shelf in polished chrome of model complementry K-25066IN-CP of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing and fixing covered toilet paper holder with shelf (Similar to Model - complementry, Code No. K 5633IN-CP of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing and fixing C.P. brass angle valve of approved quality (Similar to Model - July, Code No. K 80154IN-4-CP of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing and fixing soap dispenser with holder (Similar to Model - Cruz, Code No. K 10712D-CP of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing , fixing, testing and commissioning of one piece toilet(Similar to model San Raphel K-8688T-S-0) with quit close seat and cover in white and including floor flange accesory pack ( K-1042534) of make -Kohler or Equivalent.

Providing and fixing towel ring (Similar to Model - complementry Code No. K25067IN-CP of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing and fixing Health faucet with metal hose in polished chrome (Similar to Model - Complementary, Code No. K 12927IN-CP of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Supply of aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS:3564, embossed on the body, door weight upto 120 Kg and door width from 701 mm to 1000 mm ) with double speed adjustment with necessary accessories and screws etc , Complete (Make : Hardwyn or equivalent)

Providing , fixing, testing and commissioning of Manual valve in polished chrome,Model No. K99924 IN-CP including Aqua Turbo 360 trim Model No. K99926IN-CP of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing , fixing, testing and commissioning Bath Spout with Divertor in polished chrome of Model No. K 23511IN-CP also of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing , fixing, testing and commissioning of single function Handshower with hose in polished chrome of Model No. K 98445IN-CP of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing , fixing, testing and commissioning of showerhead of Model No- K- 9302 T- CL-CP of size 330 mm ultra thin square with 127 mm ceiling mount shower arm K-11623IN of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing , fixing, testing and commissioning of Square 54 Nozzle Body Sprary with smoothing spray in polished chrome of Model No. K 8002IN-CP water tile of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing , fixing, testing and commissioning of Grid Drain (Similar to Model - Complementary, Code No. K 45432IN-CP of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing , fixing, testing and commissioning of Floor Drain of 900 mm size (Similar to Model - Linear, Code No. K 97739T-NA of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing and fixing Soap Dish holder with shelf (Similar to Model - complementry, Code No. K 5634IN-CP of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing , fixing, testing and commissioning of wash basin of size similar to model Forefront K- 2749T-1-0 of make -Kohler or equivalent as per direction of Engineer-In-Charge.

Providing and fixing Handshower slide bar trim (Similar to Model - Complementary, Code No. K 72740T-CP of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing and fixing of magnifying glass of circular shape (size 200 mm Dia) including all fixtures of stainless steel as per the direction of Engineer-In-Charge.

Providing and fixing glass shelf of size 0.50x 0.125 m model No.K-5636IN-CP of make Kohler or equavalent with necessary fittings & screws etc. all complete as per the direction of Engineer-in-charge.

Providing , fixing, testing and commissioning of Bottle trap 350 mm (Similar to Model - Complementary, Code No. K 75823IN-CP of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing and fixing Double robe hook (Similar to Model - Avid, Code No. K 97500T-CP of Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing and fixing in wall lining/ ceiling Calcium silicate Board, with necessary fixing arrangement and screws etc. complete

6 mm thick

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, ifnishing and reinforcement- All work up to plinth level :

1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources).

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 20 mm nominal size derived from natural sources).

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).

Medium shade pigment using 50% white cement 50% Grey cement

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Electric resistance or induction butt welded tubes

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500 - 600mm)

Gutter (600 mm over all girth)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing cement concrete surface drain including earth work in excavation 10cm thick base concrete and 23 cm thick side walling with 1:3:6(1 cement 3 sand:6graded stone agg. 40mm nominal size) finishing with 1:4(1cement :4 sand ) including floating coat of neat cemetn including drain and its top and exposed surface including earthwork in excavation and disposal of surplus earth etc., complete

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade 60.1.1) Area of slab upto 0.50 sqm

Providing , fixing, testing and commissioning of Single Control tall basin faucet without drain in polished chrome of Model - K-72298IN-4ND-CP Make - Kohler or Equivalent) complete as per direction of engineer-in-charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white colour and other side of board laminated with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)

18 mm thick

Providing and fixing brass premium heavy tower bolts make of dorset or equavalent with necessary screws etc. complete :

250 mm model No-TB R1010-10' Finish-FG

Providing and fixing FSS finished brass sliding door bolts , with nuts and screws etc. complete :

300 mm (Similar to Model No. 5175 of Make - IPSA or Equivalent)

Supply of FSS finished brass hangng type floor door stopper (similar to OPASA series Model No. 8510 of Make - IPSA or equivalent )with necessary screws etc. Complete

Providing and fxing 257 mm Door Handle make dorset model No-MY 08 PR FG or equavalent with necessary screws etc. complete.

Supply of ball bearing brass hinges with necessary screws etc, complete.

Providing and fixing soil waste and vent pipe with upvc soil pipes conforming to IS: 13592 type (B ) i/c jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expension.Single Socketed.

110 mm dia

75 mm dia

160 mm dia

Providing and fixing UPVC moulded door bend of required degree for upvc soil pipes conforming to IS: 13592 type (B ) i/c jointing with solvent.

Providing and fixing UPVC (SWR) plain bend of required degree (6kg/Sqm)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

20 mm nominal dia Pipes

25 mm nominal dia Pipes

Providing and fixing 12 mm thick plain toughen glass as handrail with necessary SS finished bottom support and top rail fixed with necessary rubber fixtures all complete screws adhesives etc. all complete as per the direction of Engineer-In-Charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink with drain board 73.1.1) 510x1040 mm bowl depth 250 mm

Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge

25 mm average thickness

Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.

Bars upto 12 mm diameter

Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-In-Charge.

Upto and including 12mm dia.

Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.

SBR Polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer

Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.

12 mm average thickness.

Providing and placing micro concrete along with chicken mesh including Surface preparation to receive micro concrete by chipping to depth of maximum 75 mm,cleaning , removing the traces of dust , loose concrete etc. including the cost of all labour charges, minor tools etc complete.

Resizing and refixing of taken out door/window/ventilator after providing proper brass hinges, brass handles, brass tower bolt, brass sliding bolt etc. with necessary screws, nails etc. complete as per the direction of engineer-in-charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

Providing and fixing glazing in wooden door,windows ventilator shutter and partition etc with 12 mm thick tinted toughen glass pans (Saint Gobian or equvilant) including silicon paste for jointing the glass spans as per the direction of Engineer -In-Charge.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III)derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Ornemental wood Cat-I A (Padauk)

Providing and fixing Ist quality Digital Concept ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing single piece water closet with accessaries of make Jaquar of model no. LYS-WHT-38851P180UFSM or equivalent of good quality as per the direction of Engineer-In-Charge.

Providing and fixing wall Hung Basin with fixing Accessories set, Size 565x440x210mm (Model No. FLS-WHT-5801) FLS-WHT-5301 full pedestal for FLS-WHT-5801 with basin tap 1/2" (FLR-CHR 5011N ) and Waste coupling 32mm Size Full Thread with 80mm height (ALD-705) of make jaquar or equivalent of approved quality as per the direction of Engineer-In-Charge.

Providing and fixing Single towel rail 600 m long of make Jaquar ( AKP 35711PS) as per the direction of engineer in- charge.

Providing and fixing towel ring round if make Jaquar (AQN-7721) as per the direction of engineer in- charge.

Providing and fixing bib cock with Wall Flange of Model No. LYR-38037 of make jaquar or equivalent of good quality as per the direction of engineer-In-Charge.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :

100 mm inlet and 100 mm outlet 93.1.1) Sand cast iron S&S as per IS: 3989

Providing and fixing glass shelf 550 mm long of Model No.AQN-7771 of make Jaquar or equivalent of good quality as per direction of Engineer-In-Charge.

Providing and fixing Toilet roll holder of make Jaquar AKP-35751P or equivalent of approved quality as per the direction of Engineer-In-Charge.

Providing and fixing Soap Dish Holder of make Jaquar ( AKP-35731P) or equivalent ) as per the direction of Engineer in- charge.

Providing and fixing Hand Shower (Health Faucet) with 8 mm dia, 1.20 meter long flexible tube & wall Hook (Code No.ALD- 573) Make Jaquar.

Providing and fixing overhead shower of model no. OHS-1999 with shower arm of model no. SHA-477 casted 190 mm long light body round shape for wall mounted shower with flange of make Jaquar or equivalent of good quality as per the direction of Engineer-In-Charge.

Providing and fixing 2 way bib cock of of make model No.CON-041KN or equivalent as per the direction of engineer in charge.

Providing and fixing Central Hole Basin mixer wihout popup waste System with 450 mm long Braided Hosesof Model No. CON- 167KNB of make Jaquar or equivalent of good quality as per the direction of Engineer-In-Charge.

Providing and fixing Wall mixer 3 in 1 of make jaquar of model no. FLR-CHR 5281 N or equivalent of good quality as per the direction of Engineer-in-Charge.

Providing and fixing Hand shower of 95 mm dia round shape multi flow (ABS body chorme plated with gray face plate) with rubit cleaning system of make Jaquar (HSH-1739) including shower tube of 12 mm dia & 1.5 m long with Nuts of make Jaquar (SHA-549D12) & premium wall bracket for hand shower, 35 mm dia & 100 mm long round shape of make Jaquar (SHA-555) as per the direction of engineer in- charge.

Providing and fixing tumbler holder of make jaquar of model no. AKP 35741P or equivalent of good quality as per the direction of Engineer-in-Charge.

Providing and fixing Corner glass shelf(With bracket) of Model No.ACN-1173 of make Jaquar or equivalent of good quality as per direction of Engineer-In-Charge.

Providing and fixing waste coupling of make jaquar of model no. ALD-705 or equivalent of good quality as per the direction of Engineer-in-Charge.

Providing and fixing towel rack of make jaquar of model no. AHS 1581 or equivalent of good quality as per the direction of Engineer-In-Charge.

Providing and fixing hot &cold lead connector pipe 450 mm long braided hose with two 15 mm nuts & rubber washers without nipple of make Jaquar (ALD- 805B) as per the direction of engineer in- charge.

Providing and fixing Angular Stop Cock with wall flange of make Jaquar (CON-059 KN) as per the direction of engineer in- charge.

15 mm nominal bore

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing Bottle Trap (with internal partition) 32 mm size with 250 mm 7 190 mm Long wall Connection pipes & Wall Flanges Model No. ALD-769L250 x 190 of make jaquar or equivalent as per the direction of Engineer- In -Charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

32 mm nominal dia Pipes

40 mm nominal dia Pipes

50 mm nominal dia Pipes