SPL REPAIR OF BLDG NO T73 AND ALLIED INFRA AT HQ 87 MTN BDE GARHI CANTT BLDG NO P19 B OPEN GARAGE 4X5/7.5 ALS AND T-1 PROVN OF CERTAIN STEEL CAGING FOR OH WATER TANKS AT SIKH RAGT

Amount

Dismantling Asbestos cement (corrugated, semi-corrugated etc) sheets in roof covering complete all as specifed and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.60 mm thick crimpted/tapard at the external end slo of any colour having tensile strength 550 Mpa as in roof covering fixed with self tapping screws and caps etc complete all as specified and directed.

Plain galvalume aluminium zinc coating GI based plain steel sheet 0.63 mm thick in ridges, hips, valley gutters at the external end slop of any colour having tansile strength 550 Mpa as in roof (ridges) covering fixed with self tapping screws and caps etc complete all as specifed and directed.

Rolled Mild steel joist channels, angle or tee sections, fixed indepently witout connecting plates etc. (cut to ordinary length, fixed with hold fast and nails to floors and similar work welding & drilling of holes to floor for fixing of hold fast as per requirement of gde Fe-410W (Gde E-250 quality), complete all as specifed and directed by Engr-in-Charge.

AC designer composite ceiling board 4 to 6 mm thick in 600 x 600 mm panel confirming to IS-14682 type-B Category-3 including GI frame, hold fast and suspenders complete all as specified and directed by Engr-in-Charge. Make : Everest/V Board

Dismantling wall and ceiling boards, fibre pulp insulation etc) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specifed and directed.

Taking down chowkhats or steel frames not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specifed and directed.

Taking down chowkhats or frames with shutters with fittings (without taking off shutters from the frame) of size exceeding 1.5 Sqm not exceeding 4 sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts and removing from site to store or otherwise complete all as specified and directed.

Pressed steel frames made of 1.25 mm thick MS sheet of profile 125 x 60 mm for door and window frames with one or more rebates including lock strike plate, shock absorber, 20 mm dia 60 mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified and directed.

Factory made 35 mm thick 2nd class hardwood (Hollock), plain framed, panelled shutters (two panels) with lock rail and panels of 9 mm thick BWP ply or of 12 mm thick BWR grade veneered particle board medium density, with commercial veneering on both faces. The size of rail and stile as per IS : 1003 part- I, klin seasoned and chemically pressure treated complete all as specified and directed.

Factory made, 2nd class hard wood 35 mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauze etc complete all as specified and directed.

Aluminium anodized handles 150 mm long dia "D" type fixed to doors with screws complete all as specified and directed.

Aluminium anodized tower bolts 150 mm long fixed to doors with screws complete all as specified and directed.

300 mm long aluminium anodized sliding door bolt with hasp, staple (bolt type) and fixing clips, bolts and sliding bolts etc. complete all as specified and directed.

Mild steel 150 mm ordinary rat and tail springs (Helical door springs) welded or screwed to any type of door frames including roller and roller plate complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins arches pillars etc complete all as specifed and directed.

Brick work with sub class 'B' bricks straight or curved on plan exceeding 6.00 m mean radius built in cement mortar 1:6 complete all as specifed and directed.

Demolition cement concrete in ground floors and paving (unreinforced) not exceeding 15 cm thickness (below or above ground floor) complete all as specified and directed.

75 mm thick plain cement concrete, type C-2, (1:3:6) (using 40 mm graded aggregate) as in plinth protection complete all as specifed and directed.Providing joints through out the thickness of the plinth protection field with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight.

Providing 100 mm thick, plain cement concrete type B-2, (1:2:4) (using 20 mm graded aggregate) as in floors laid in separate bays complete all as specifed and directed.

25 mm thick pcc type B-0 1:2:4, (using 12.50 mm graded crushed stone aggregate) as in sub base finished fair for receiving floor finishes complete all as specifed and directed.

Screed bed or bedding layer of mortar 10 mm thick for laying floor tiles in cement mortar 1:4 complete all as specifed and directed.

Non skid ceramic joint free tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm and not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the slurry complete all as specifed and directed.

10 mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:4 as in backing coat to recieve tiles as in vertical surfaces and finished even and fair complete all as specifed and directed.

Glazed ceramic tiles in vertical surface but 600 x 300 x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specifed and directed.

Taking down cement plaster from brick walls or concrete of any description, racking out joints hacking for key scrubbing down with water etc complete all as specifed and directed.

Rendering 15 mm thick in two layer (10 mm + 5 mm) on brick work or concrete surfaces in cement mortar 1:4 finished even and fair without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specifed and directed. Note : Water proofing compound to be measured and paid for separately).

Preparation of new plastered or un-plastered surfaces and walls including cornices, pilasters etc and applying two Coats of cement base paint over a coat of primer complete all as specifed and directed.

Rendering 10 mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specifed and directed.

Preparation of new plastered or unplastered surfaces of wall and apply two coat of oil bound distemper over a coat of primer including two coats of wall care putty wall care putty complete all as specifed and directed.

Preparation of new wooden or wood based surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specifed and directed.

Steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specifed and directed. Note : ( i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 ( ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

All as per ser item No 32 but without glazing bar complete all as specifed and directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

3 mm thick sheet glass ordinary quality and glazing with oil putty in square pane complete all as specifed and directed.

Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steelwire staples or complete all as specifed and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Preparation of old surfaces and applying one coats of synthetic enamel paint on steel surface of any description exceeding 10 cm width or girth complete all as specified and directed.

Preparation of new surfaces on steel surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint on complete all as specified and directed.

Factory made mild steel ventilators box type with upper top hung with glazed and gaused shutters and bottom openable,locking arrangements type shutters including pintol hinges,steel peg stay and one shop coat of red oxide primer complete all as specifed and directed. Note : ( i) The window shall be fabricated as per Drg No CEUZ/TD/1302/2009 Sheet 1/3 to 3/3 (ii) Glazing, wire gauge and Glass shall be measured and paid for separately.

Supply only liquid water proofing compound complete all as specifed and directed.

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specifed and directed.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor complete all as specifed and directed.

PCC 1:3:6 type C-2 (using 40 mm graded aggregate) in surafce channel and drains complete all as specifed and directed.

Extra for forming fair finished drain or channel exceeding 30 cm inner girth in cement concrete, using extra cement, including forms moulds, mitered/stopped ends etc complete all as specifed and directed.

Cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregated) as in roof kerbs or mud stops, rounded or chamfered on edges, roof or padding including necessary form work fair finished surfaces complete all as specified and directed.

Rendering 10 mm thick cement plaster on roof surfaces in cement mortar 1:3 with IWPC finished fair and even without using extra cement complete all as specifed and directed. Note: WPC shall be measured and paid seperately.

Pressed steel frames for doors made out of 1.25 mm thick MS sheet with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate 12 mm bar thresh hold etc. complete, of frame size 105 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specifed and directed.

38 mm wide Glass dividing strips, 3 mm thick and inserted in position to conform to design complete all as specifed and directed.

Preparation of old surfaces and applying two coats of cement base paint on walls complete all as specified and directed.

Preparation of newly plastered/unplastered surfaces and applying three coats of white wash on walls complete all as specifed and directed.

Preparation old surfaces including complete removal of existing surface of white wash and applying two coats of white wash on walls complete all as specifed and directed.

Dismantling of plain or corrugated steel sheetings any thicness as in roof coverings complete all as specifed and directed.

Screed bed or bedding layer of mortar 20 mm in cement mortar 1:4 floor finishes complete all as specifed and directed.

Machine cut kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specifed and directed.

Dismantling floor/hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Machine cut kota stone slab flooring 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed 20 mm and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specifed and directed.

75 mm butt hinges, medium weight, cold rolled mild steel all as complete all as specified and directed.

18/19 mm thick block boards grade 2 quality enterior grade, Commercial type fixed with screw or Steel fram/Timber frame including teak wood lipping, 6 mm thick fixed with Nail complete all as specified and directed.

100 mm size hasp and staple safty type aluminum anodized with mild steel hinges pin including bolt to hinge plate and fixed with screw complete all as specifed and directed.

Mild steel, 150 mm, ordinary rat tail rod pattern door spring including roller and roller plate complete all as specifed and directed.

Ball catches with 8 mm dia steel balls and brass body and striking plate including letting in and fixed complete all as specified and directed.

Taking down 15 mm bore steel tubing and connections including all fittings and removing to store complete all as specified and directed.

Taking down 20 mm bore steel tubing and connections including all fittings and removing to store complete all as specified and directed.

15 mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete all as specified and directed.

20 mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete all as specified and directed.

Refixing 15 mm bore old steel water tubing medium grade galvanised and connections in new or old position (walls, ceiling, floor etc.) complete all as specified and directed.

Refixing 20 mm bore old steel water tubing medium grade galvanised and connections in new or old position (walls, ceiling, floor etc.) complete all as specified and directed.

Gun metal globe of gate valve with iron wheel head, screwed both ends of size 15 mm in repair complete all as specified and directed.

Gun metal globe of gate valve with iron wheel head, screwed both ends of size 20 mm in repair complete all as specified and directed.

Disconnecting existing tanks of capacity exceeding 250 litres and not exceeding 500 litres, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

Disconnecting existing tanks of capacity exceeding 500 litres and not exceeding 1000 litres, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

Rotational moulded polyethylene water storage tanks 1000 ltrs (cylindlerical verrtical with closed top) hoisted and fixed in position all as specified in SSR part I complete all as specified and directed.

Rotational moulded polyethylene water storage tanks 500 ltrs (cylindlerical verrtical with closed top) hoisted and fixed in position all as specified in SSR part I complete all as specified and directed.

Cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as raising plate form of over head tank etc complete all as specified and directed.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing; frame work, including locking arrangement for water tanks and similar work confirming to Fe 290 Gd E-165 complete all as specified and directed.

Hard Drawn steel wire fabric cut to length bent to shape required and tying, welding to the angle iron frame etc complete all as specified and directed.

Ball brass valve high pressure with polythene float and fly nut complete of size 20 mm fixed in repair complete all as specified and directed.

Providing and fixing 12 mm thick gypsum board including GI U section 50 mm x 35 mm x 0.7 mm & edge side GI U-section size 25 mm x 15 mm x 0.7 mm fixed with screws to gypsum board and frame grid suspended with soffit cleats to roof slab for hanging 4 mm dia GI hanger rod with adjustable level clips after fixing of gypsum board joints/junction of gypsum board ciling to be cover ed with 50mm strip complete all as specified as per manufacturs instruction, including recessing for provision of ceiling lights and applying two coat of oil bound distemper over and including 2 mm POP to visible side of gypsum board ceiling shade/tint including decorative ceiling boarder complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position etc complete all as specified and directed.

Digital vitrified ceramic tiles 10 mm thick (square/rectangular) polished dark/light shade, double charged/ultracharged tile area of each tiles exceeding 0.42 sqm but not exceeding 1.00 Sqmtr in floors etc and jointed in neat cement slurry and pointed in white or coloured cement to match the work using dark shade complete all as specified and directed.

Digital vitrified ceramic tiles 10 mm thick (square/rectangular) polished dark/light shade, double charged/ultracharged tile area of each tiles exceeding 0.42 sqm but not exceeding 1.00 Sqmtr in vertical surface etc and jointed in neat cement slurry and pointed in white or coloured cement to match the work using dark shade tiles in vertical surface complete all as specified and directed.

Preparation on old or new plastered surfaces and applying two coats of weather proof exterior emulsion paint complete all as specified and directed.

Preparation of surfaces of old or new surfaces including removal of old treatment and applying a thin layer of plaster of paris to give a uniform finish as approved and complete all as specified and directed by Engr-in-Charge.

Cornice with plaster of paris of approved design asin corners complete all as specified and directed.

Preparation of new/old treated walls and ceilings and applying two coats of plastic emulsion paint of any shade complete all as specified and directed by Engr-in-Charge. (Royal Emulsion)

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in trenches including spreading, leveling watering and well ramming in layers not exceeding 25 cm complete all as specified and directed.

Removing of surplus soil not exceeding 50 m and deposited where directed at a level not exceeding 1.50 m above the starting point complete all as specified and directed.

Hard core of broken stone of guage not exceeding 63 mm deposited spread and levelled in layer not exceeding 15 cm thick watered and well rammed to true surfaces complete all as specified and directed.

PCC 1:4:8 type D-2 (40 mm stone aggregate) filling mass concrete in foundation complete all as specified and directed.

Reinforced Cement Concrete M-25 design Mix (using 20 mm graded aggregate) as in foundation including rafts, footings, foundation beams, plinth beams, bases of columns etc complete all as specified and directed.

Reinforced Cement Concrete M-25 design Mix (using 20 mm graded aggregate) as in columns, pillars, piers, posts and struts complete all as specified and directed.

Reinforced Cement Concrete M-25 design Mix (using 20 mm graded aggregate) as in beams, cantilever, lintels over 1.5 m complete all as specified and directed.

Reinforced Cement Concrete M-25 design Mix (using 20 mm graded aggregate) as in slabs supported on walls, beams and columns in floor, roof, landing, balconies, conopies, decks, slab and in shelves and like complete all as specified and directed.

Use and waste formwork to sides of concrete foundation footings base of coloumns sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for rough finished flat surface of concrete complete all as specified and directed.

Use and waste formwork to sides of columns, pillars, posts, struts, piers and stanchions, rectangular or square for rough finished flat surfaces of concrete complete all as specified and directed.

Use and waste formwork to sides and soffits of floor or roof beams, beam hunching, girders, lintels, cantlievers, shelves including supports etc for rough finished flat surfaces of concrete complete all as specified and directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or slopping) for rough finished flat surfaces of concrete complete all as specified and directed.

Use and waste of form work to edges of concrfete flats, slabs etc including fair finished surface complete all as specified and directed.

Mild steel TMT bars 10 mm dia and over cut to lenth, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding waith and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per ser item No 100 here-in-before but 6 to 8 mm dia complete all as specified and directed.

Glazed anodised (15 micron) powder coated Aluminium door made out of extruded section as standard door frame, single groove of size 100 x 45 x 2.5 mm thick standard shutter top and bottom section of size 95 x 45 x 2.5 mm thick standard shutter vertical section of size 80 mm x 45 mm x 2.5 mm thick complete with auto hydraulic floor mounted door closer handle special cylindrical lock, neoprene dry set, rubber gasket, with 12 mm thick prelaminated (both side) particle board and 5 mm thick plain glass complete all as specified and directed.

Powder coated aluminium window side hung aluminium window frame or chowkats 1.5 mm thick aluminium anodized of size 65 mm x 40 mm and window shutter frames (sides rail, top rail, bottom rail and middle rail) 1.5 mm thick aluminium anodized of size 45 mm x 45 mm including all fitting such as rubber gasket aluminium glazing clips, locking arrangement and 75 mm aluminium handle and including 5 mm thick tinted plain glass in panels fixed with rubber, gasket and aluminium beads, aluminium tower bolt 100 mm, aluminium butt hinges 75 mm 02 No in each shutter, complete all as specified and directed by Engineer-in-Charge Note : Size of window shall be as per site requirement.

Powder coated aluminium window side hung aluminium window frame or chowkats 1.5 mm thick aluminium anodized of size 65 mm x 40 mm and window shutter frames (sides rail, top rail, bottom rail and middle rail) 1.5 mm thick aluminium anodized of size 45 mm x 45 mm including all fitting such as rubber gasket aluminium glazing clips, locking arrangement and 75 mm aluminium handle and including stainless wire cloth fixed with aluminium beads, aluminium tower bolt 100 mm, aluminium butt hinges 75 mm 02 No in each shutter complete all as specified and directed by Engineer-in-Charge Note : Size of window shall be as per site requirement.)

Powder coated aluminium frame and grill for door, window, ventilators with one or more rebated including jointing cleat for fixing etc complete all as specified and directed.

Stainless steel hand rail of 16 gauge tube 50 mm dia at top 37 mm dia of balusters and two Nos 20 mm dia intermediate tubes including all necessary cups and washers complete all as specified and directed.

Stainless steel master pillars for stainless steel railing and size 32 mm to 50 mm and height 0.90 to 1.20 m required as per site requirement as approved by the users complete all as specified and directed.

Glazed anodized (15 Micron) powder coated aluminium partition made out of aluminium extruded section frame (100 mm x 45 mm x 2 mm) completely with rubber gasket, partly glazed with 5 mm thick plain glass and partly panelled with 12 mm thick prelaminated particle board (both side laminated) complete all as specified and directed. Note: 5 mm plain glass and 12 mm thick particle board is deemed to be included in the unit rate.

Taking down carefully, copper/aluminum point wiring (light, fan, socket or power) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as specified and directed.

Point wiring for one light/fan point controlled by one way switch using 1.5 Sqmm FRLS copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5 mm and 20 mm dia), medium grade with sunk Cl/Pressed steel terminal boxes with 3 mm thick laminated sheet cover including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5 Sqmm as earth wire stranded and conected to earth dolly complete all as specified and directed.

All as per ser item No 110 but for 3 pin 5 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 sqmm earth wire and connected to earth dolly complete all as specified and directed.

All as per ser item No 110 but for 3 pin 5 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 sqmm earth wire and connected to earth dolly complete all as specified and directed.

All as per ser item No 110 but for 3 Pin 15 Amps socket outlet independent with cable 2.5 Sqmm including copper PVC insulated PVC unsheathed 1.5 sqmm earth wire standard and connected to earth dolly complete all as specified and directed.

Switch piano flush type 5 Amps single pole one way complete all as specified and directed.

Socket 3 Pin 6 Amps flush type complete all as specified and directed.

Switch socket combination 2-in-3 pin 5 Amps flush type complete all as specified and directed.

Switch socket combination 2-in-1, 3 pin 5 & 15 Amps flush type complete all as specified and directed.

Replacement MCB Single Pole, 230 Volt, Raiting 6 to 32 Amps complete all as specified and directed. Make : Indoasian Cat Part No : 811015 or equivalent make in Havells/Legrand. Note : MCBs required to fix in existing DBs.

Replacement MCB Single Pole and Neutral, 230 Volt, Raiting 40 to 63 Amps complete all as specified and directed. Make : Indoasian /Havells/Legrand

Sheet metal enclosure MCB distribution board single pole and neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Make : Indoasain/Havells/Legrand Note - MCBs will be measured separately.

Replacement sheet metal enclosures for DBs when MCBs to be used double door DB TPN 4 way 415 volts with 200 amps rated bus bar complete all as specified and directed. Make : C&S/Indoasian/Legrand.

Replacement MCB TPN 415 volts, 10 KA, 4 Pole 63 Amps 'C' Curve Opti Pro complete all as specified and directed. Make : C&S/ Indoasian/Legrand.

Replacement of fan regulator electronic, stepped type hum free suitable control speed of fan from 0 to 100 % and connecting electrically complete all as specified and directed. Make : Anchor/Legrand/Kinjal.

New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 20 W complete all as specified and directed by Engineer-in-Charge. Make - Havells, Cat Part No LHEXBXPNIN1W020 or equivalent to Polycab/ HPL/Bajaj

Replacement of New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 10 W complete all as specified and directed by Engineer-in-Charge. Make - Havells, Cat Part No LHEXBXPNIN1W010 or equivalent to Polycab/HPL/Bajaj

Replacement of LED bulk head luminaire, 10 W (ENDURA RUGBY) 230 Volts wall/surface mounted complete with with LED lamp 10 watt, with all accessories, pre-wired, including providing flexible copper wire, twin core cable complete all as specified and directed by Engineer-in-Charge. Make : Havells, Cat Part No LHEOAOP7UZ6W010 or equivalent HPL/ Bajaj

LED Street light 30 W including angle arms (Bracket) with 25 mm dia GI pipe complete all as specified and directed by Engineer-in-Charge. Make - Wipro Product Code - D923065 or equivalent to Havells/HPL/Bajaj

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 6 Sqmm in PVC concealed conduit 25 mm dia including PVC insulated copper conductor cable 4 Sqmm as earth lead complete all as specified and directed. Including taking down old sub main wire.

Earthing complete with galvanised steel earth plate electode 600 mm x 600 mm x 6.00 mm thick burried directly in ground (earth pit not less than 2.25 meter deep below normal ground level connected to and including galvanised steel earth lead wire 4 mm dia by means of bolts, nuts, chock, nuts and washers of galvanised iron or steel including PCC Pit in 1:2:4 type B-1 angle iron frame with RCC cover and handle, excavation and earth work in any type of soil medium grade GI watering pipe 20 mm bore with funnel and wire mash and light grade GI protection pipe 15 mm bore upto main board complete all as specified and directed as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected to main control board as specified and testing completion.

Trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 25 Sqmm x 4 core size complete all as specified and directed including taking down old cable. Note : Earth work and other connected work shall be measured and paid sperately.

Trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 10 Sqmm x 2 core size complete all as specified and directed including taking down old cable. Note : Earth work and other connected work shall be measured and paid sperately.

Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying and streching the cable in trenches, including hand punning and consolidating complete all as specified and directed. Note : for payment purpose punned thickness shall be measured

Bricks sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and directed.

GI tubing light grade 40 mm dia along the wall/in trenches/in duct/in culvert/road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles complete all as specified and directed.

Point wiring for one light point/fan point/Bell point controlled by one switch with 1.5 sqmm PVC insulated FRLS unsheathed copper conductor single core multi stranded flexible copper cable in and including not less than 2.00 mm thick 20 mm dia non metallic rigid PVC conduit (ISI marked) concealed in wall with 1.5 mm thick pressed steel terminal boxes (modular type) concealed in walls painted the same inside and out side with one coat of black bitumen paint including inner and outer sheet for fixing of modular switches/ regulator etc along with PVC insulated and in sheathed FRLS 1.5 sqmm multi stranded copper conductor cable (green color) as earth lead complete all as specified and directed by Engr-in-Charge.

All as per ser item No 135 but for 3 pin 5 Amp Socket outlets point controlled by one push button on Independent board with 1.5 sqmm PVC insulated unsheathed FRLS copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed FRLS copper conductor single core cable (green color) as earth lead complete all as specified and directed by Engr-in-Charge to match with the existing specification.

All as per ser item No 135 but for 3 pin 5 Amp Socket outlets point controlled by one push button on Same board with 1.5 sqmm PVC insulated unsheathed FRLS copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed FRLS copper conductor single core cable (green color) as earth lead complete all as specified and directed by Engr-in-Charge to match with the existing specification.

All as per ser item No 135 but for 3 pin 15A socket outlet on the independent board with 4 sqmm PVC insulated unsheathed FRLS copper conductor single core multi strand flexible cable and 2.5 sqmm PVC insulated unsheathed FRLS copper conductor single core cable (green color) as earth lead & complete all as specified and directed by Engr-in-Charge to match with the existing specification.

Switch piano modular type, 1 module, 10 Amps, 230 volts one way complete all as specified and directed. Make - Anchor/ Havells/Legrand

Switch piano modular type, 1 module, type 20 Amps 230 volts one way complete all as specified and directed. Make - Anchor/ Havells/Legrand

Socket outlet modular type, 2 module, 5 pin, 10 Amps combined complete all as specified and directed.Make - Anchor/Havells/Legrand

Socket outlet, modular type, 2 module, 2-in-1, 20 Amps combined complete all as specified and directed. Make - Anchor/Havells /Legrand

Ceiling rose surface bakelite 3 terminals in repair complete all as specified and directed. Make : Cona, Cat Part No 2126/SSK Cat Part No 572 or equivalent of make in Havells/ Anchor/Kolors.

Slim type 36/40 Watt 2 x 2 LED Flat Panel light with diffused optics (600 x 600 x 12 mm) complete making all connection using 1.5 sqmm copper conductor multistarnd PVC insulated 3 core flexible cable complete all as per the directions of Engr-in-Charge. Make - WIPRO/Havells or equivalent make in Wipro (Garnet Slim)

9 watt LED Bulk Head fitting complete making all connection using flexible cable of suitable size from ceiling rose to fitting complete all as per the directions of Engr-in-Charge. Make - Syska LED Cat Part No - SSk-BH-9W or equivalent make in Havells, wipro, C&S.

LED tube light fitting 2 feet Garnet 10W Batten LED, Housing made of extruded AL with lumen O/P should not be less than 100 lum/watt making all connection with suitable size flexible cable from ceiling rose to fitting complete all as specified and directed. Make - Wipro, Product code - D531065 or equivalent make in C&S/Havells

MCB TPN 415 volts, 6KA, 63 Amps complete all as specified and directed. Make : Indoasian Cat Part No : 811218 or equivalent make in Havells/Legrand.

Wall fan 4000 mm sweep SP, AC, 230V, plastic body alongwith Louvers including making hole of suitable dia in existing wall and all necessary connection from ceiling rose to fan complete all as specified and directed by Engr-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.30 mm thick buried directly in ground (earth pit not less than 2.25 Mtrs below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised earth lead 4 mm dia by means of bolts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test point all as specified and indicated and testing on completion including excavation earth work drilling holes for electrode PCC pit & cover, funnel, water pipe lugs GI pipe medium grade protection pipe for earth lead up to DBs complete all as specified and directed.

Switch socket combination 5 Amps 2-in-1, 5 Pin flush type, 230 volts in repair complete all as specified and directed.

Switch socket combination 5 pin 16 Amp, flush type in repair complete all as specified and directed.

Taking down ceiling fan/Exhaust Fan including disconnection of existing connection, dismanting of blades and Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and rehanging the fan complete all as specified and directed.

LED tube light fitting 4 feet Garnet 20W Batten LED, Housing made of extruded AL with lumen O/P should not be less than 100 lum/watt making all connection using flexible cable of suitable size from ceiling rose to fitting complete all as specified and directed. Make - Wipro, Product code - D532065 or equivalent make in C&S/Havells

Replacement Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 12 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Note - MCBs will be measured separately.

Replacement MCB Single Pole and Neutral , 230 Volt, B-Series, Raiting 6-32A, complete all as specified and directed. Make : Indoasian, Cat Part No : 811034 or equivalent make in Havells/Legrand.

Trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 16 Sqmm x 2 core size including taking out old unservicebale UG cable any type/size complete all as specified and directed.

JINDAL BUILDERS