Beautification and Illumination of Surrounding at Siddhivinayak Devasthan Kumbharwada Sancorda Dharbandora Goa

Amount

CIVIL WORKS

Demolishing laterite stone masonry in cement mortar including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead.

Earthwork in excavation over areas by mechanical/mannual means at all depths in all type of strata comprising any of the materials such as soil, silt, sand, clay, gravels, moorum of all varieties, shingles, pebbles, all types of conglomerates, all types of laterite rock, soft rock, disintegrated rock, fissured/ shattered/ decomposed rock or weathered rock and all such other materials as described under appendix to these specifications whether in full or in parts as the case may be adopting any approved method or methods as may be convenient or permitted inclusive of chiselling, wedging etc. in all conditions such as dry, moist, saturated, submerged, foul conditions etc. including dressing of sides and ramming of bottoms, including getting out the excavated soil at all lifts, including pumping or bailing out water as directed by the Engineer on site including segregating the excavated earth along with crushed rock pieces of size 75mm and below and disposal of surplus excavated earth as directed by Engineer within a lead of 50mt and all lift and including breaking of excavated rock into boulders of size ranging from 150mm to 300 mm and stacking the broken boulders at a place specified by the Engineer on site etc. complete

Refilling the pipeline/foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth as directed by Engineer in Charge.

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement.

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement.Extra for laterite masonry in all sizes in superstructure from floor I level upto floor V level

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4gradedgranitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: (a) All works upto plinth level

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size) (a) All works upto plinth level

(b) In walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and structs etc. upto floor five level

(c)In beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases upto floor five level

Reinforced cement concrete work 1:1½:3 (1 cement: 1½ coarse sand: 3 granitic or basaltic stone aggreate 20mm nominal size excluding plastering and cost of centering, shuttering & reinforcement, in sloping or battering surface (slabs, beams, louvers, etc) (i) Where inclination to the horizontal does not exceed 30°

Providing TMT steel reinforcement bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) ) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member.

Centering & shuttering including Strutting, Propping & removal of forms for : (i) Foundations, Footings, Bases for columns

(iii) Columns, Piers, Pillars, Aburments, Posts and struts (square rectangle polygon in plan)

( iv) Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders, Bressumers and Lintels plinth beams not exceeding 1m in depth

Centering & shuttering including Strutting, Propping & removal of forms for sloping or battering surface (slabs, beams, louvers, etc) including folded plates (i) Where inclination to the horizontal does not exceed 30° requiring shuttering on the underside only

Providing woodwork in frames of doors, windows, clerestory windows trusses & other frames wrought framed and fixed in positon. (b) Second class Indian teak wood

Providing and fixing 35 mm thick panelled glazed or panelled and glazed shutters for doors, windows and clerestory window including anodized aluminium butt hinges with necessary screws: (b) Second class Indian teak wood

Providing and fixing M.S. grill of required pattern in wooden frames of Windows etc. with M.S. flats square or round bars with round headed bolts and nuts or by by screws (b) Ornamental grill

Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in charge: windows with two sliding shutters using 18 mm series shutters section. c) Figured glass Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section

Providing and laying jet black mirror polish granite flooring and dado over 20mm thick base of cement mortar 1:4 laid over and jointed with cement slurry including rubbling complete Granitic slab (jet blck with mirror polish) 20 mm thick add q0% wastage 1.00

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design / shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc. shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001: 2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm. (a) 60 mm thick in all colours except grey (M35 grade)

(b) 60 mm thick in Grey colour (M35 grade)

Providing and fixing Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps and dados, jointing with grey cement slurry @3.3 kg per sqm, including pointing/grouting in white cement mixed with pigment of matching shade complete (b) 600 x 600 mm - light Shades

12mm cement plaster 1:4 (1 cement : 4 fine sand)

6mm cement plaster to ceiling 1: 3 (1 cement : 3 fine sand)

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge.

Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.

Painting three or more coats with acryllic exterior paint of approved brand and manufacture (Such as Dulex/ Asian Paints/ Sherwin Willians) including applying one coat of cement primer and one coat of surface treatment etc. complete.

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Construction of Deepstambh of exposed Laterite Masonry in circular shape including moulding, extra as per the detailed drawings and as directed by engineer incharge.

Supplying and fixing Marble Tulsi Plant pot on the base of Laterite Masonry, etc. as per the detailed drawings and as directed by engineer incharge.

ELECTRICAL WORKS

Supplying and fixing following way SPN sheet steel MCB distribution board Consumer Unit 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar hinged front acrylic cover for the MCB knobs detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required (but without MCB/RCCB/Isolator)(b) 2 + 8 way Cat A

Supplying and fixing 40 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required.(c) DP, Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required.(a) SP, Cat A

Supply and erecting meter box suitable for Single phase energy meter and incoming SP/DP MCB, fabricated out of 16 SWG sheet steel, powder coated, complete as required and conforming to the requirements of Goa Electricity Department.

Supply, installation, testing and commissioning of electronic type single phase energy meter (KWh), ISI marked, in polycarbonate or sgheet steel body ( base mounting type) with counter display/LCD display, with ELT, in Class 1.0, 50 Hz, 240 V. AC duly tested by MRT along with Test Certificates, complete as required of following capacity of make L & T only.(b) 10 to 40 A

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required.(b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required(c) 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface PVC conduit( medium) with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.(a) Group A -- with Cat A Modular Accessories

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/ 6 A modular switch connection painting etc. as required.(a) Cat A

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 15/16 A and 5/6 A modular socket outlet modular socket outlet and 15/16 A modular switch connection painting etc. as required.(a) Cat A

Supply of 3 core unarmoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.3 Core 2.5 sq.mm

Supply of 2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.' 2 Core 6 sq.mm

Supply of 2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.' 2 Core 10 sq.mm

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required.'(b) In rocky strata

Supply and making cable end terminations with compression gland and aluminium lugs for following sizes of PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required.(3) 2 x 6 Sq. mm.

Supply and making cable end terminations with compression gland and aluminium lugs for following sizes of PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required.(3) 2 x 10 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required.3 x 1.5/2.5 Sq. mm.

Supplying & erecting 10W-12W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Supplying & erecting LED 20W tube light fitting 2 feet), 5700K, with CRCA housing, heat sink, with industrial grade heavy duty driver complete Havels Make Philips / Wipro cat no LL24-251-XXX-57-XX (including lamp)

Supplying and fixing brass batten/ angle holder including connections etc as required.

Supply and erecting of 48 inch (1200mm sweep) ceiling fan, double ball bearing type, , complete with all accessories.(a) Cat A

Supply and erecting fan hook box ( 100 mm diameter or equivalent square size, 75mm deep) fabricated out of 16 SWG sheet steel with 10 m round bar hook bounded to RCC steel upto 50 mm length protruding on each side of the box, including painting with 2 coats of red oxide, complete as required.

Supply, Installation, Testing and Commissioning of 8mtr Octagonal poles with 130mm bottom A/F & 70 mm top A/F made up of 3mm thk. HT sheet alongwith base plate of size 200X200X16mm , 4nos. of M20 x 600 J bolts EN 8 grade. .Make RR Ispat, Transrail,Hake, Mechanize Engineering as required and directed by engineer incharge

Supply, Installation, Testing and Commissining of LED Street light fitting of 80W,including lamp, with PF > 0.95,class IP 65 and above Housing of pressure die cast aluminium alloy and heat sink extruded aluminium Complete with all required accessories Of make wipro, havells,Crompton, Nice, Reytek,Leksa, La Luminite as required and directed by engineer incharge.

Supply and Installation of 1000mm Single arm bracket PU painted suitable for Top 70MM. etc.Make Valmount, Bajaj, Transail, RR Ispat as required and directed by engineer incharge.

Supply, Installation, Testing and Commissining of Flood light of 80W, LF40-102-060-57-XX , 5700K High purity integrated IP66 lens diffuser luminaire with aluminum die cast housing having high efficancy and better thermal management with high energy saving. Complete with all required accessories Of make wipro, havells,Crompton, Nice, Reytek,Leksa, La Luminite as required and directed by engineer incharge.

Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark,of approved brands, including accessories and providing masonry enclosure with CI/RCC cover having locking /lifting arrangement and watering pipe etc. with charcoal or coke and salt) as required as per ' the Earthing Drawing provided by the Engineer Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c) Charcoal/salt as per specs ( paid seperately). d) Refilling the pit of size 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe. g)watering arrangement(plumbing will be paid seperately)'(b) In rocky strata

Supplying and laying 6 SWG GI wire at 0.5 m below ground level for conductor earth electrode including soldering etc. as required.

Extra for using salt and charcoal for pipe earth electrode as required( 65 Kgs of Charcoal and 5 Kgs of Salt).

SHUBHANGI PRAKASH BHANDARI (BID ID -46575)