REPAIRS SECURITY/JAFFRI WALL, CHAIN LINK FENCING, BARED WIRE FENCING, RETAINING WALLS, FOOT PATHS AND CONNECTED ITEMS IN SW ZONE AT RMS

Amount

Surface dressing n.exc 15cm deep in soft/loose soil including removing of bushes etc complete all as specified

Excavation in trenches n.exc 1.5 m wide and n.exc 1.50m in depth n. exc 10 sqm on plan and getting out in soft/ loose soil ,complete all as specified and as directed.

Returning, filling soil in trenches including spreading levelling, watering and well ramming in layers n.exc 25 cm complete all as specified and as directed.

Removing excavated soil not exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point all as specified and as directed.

Excavating in post holes each not exc 0.50 cum and getting out in soft / loose soil including returning, filling in and ramming earth or broken rubble mixed with earth around in layer not exc 25 cm, watering, removing surplus soil to a distance not exc 50m and making good surfaces complete all as directed

M&L for hard core of broken boulder or stone of gauge not exc 63 mm deposited , spread and levelled in layers n.exc 15cm thick watered and rammed to true surfaces complete all as specified and as directed.

M&L sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L Loose filling with Broken stone or boulders aggregates of gauge 80 to 150 mm in weep holes of retaining wall, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n.exc 15 cm thickness (below or above GL) and removing rubbish of the premises complete all as specified and as directed.

M&L for P.C.C 1:4:8 type D-2 (using 40 mm graded stone aggregate) in foundation,filling and mass concrete all as specified and directed

M & L for PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) as in for coping, hounching and the similar work, weathering slightly rounded or chamfered edges and throating including form work all as specified and diected.

M&L for R.C.C (1:2 :4) type B1 (Nominal Mix) using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintel over 1.5 span, complete all as specified and as directed.

M&L Providing precast cement concrete louvres and jallies,Type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) 25mm thick (mea sured solid) and set in cement mortar 1:4 including necessary from work and mould complete all as specified and as directed.

Use and waste of formwork to sides and soffits of floor or roof beam , lintels, cantilever, shelves ,flate, rough finished surfaces of concrete, complete all as directed.

Demolition of brick work or stone/boulder masonry built in cement mortar ,complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks , straight or curved on plan exc 6 metre mean radius as in full brick thick walls built in CM(1:6) using old size bricks complete all as specified and as directed.

M&L for brick wrok with sub-class 'B' bricks, straight or curved on plan to any radius, built in CM (1:4) using old size bricks in half brick thick walls complete all as specified and as directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted built in CM 1:6 complete all as specified and directed.

M&L for Raised pointing to random or polygonal rubble, uncoursed or brought upto courses in CM (1:4) ,complete all as specified and as directed.

M&L for pre-cast cement concrete 1:3:6 type C-1(using 20mm graded aggregate) as in kerb/ bond stone and set in cement mortar 1:4 including necessary from work and mould complete all as specified and as directed.

M&L TMT steel bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia complete as in reinforcement to concrete all as specified and as directed.

All as per serial item No 21.00 here -in-before but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders.

M&L for 75 mm PCC 1:4:8 type D-2 (using 40mm graded atone aggregate aggregate) as in sub base of floor, complete all as specified and as directed.

M&L for 100 mm thick PCC 1:4:8 type D-2 (using 40mm graded aggregate) as in floor finished the surfaces even and fair ,making impression of expanded metal whilst concrete is green complete all as specified.

M&L for 100 mm thick PCC 1:2:4 type B-2 (using 40mm graded aggregate) as in as iroof kerb , complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded aggregate) as in paving/plinth protection , laid in alternate bays, finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 40mm thick plain cement concrete 1:2:4, type B1, (using 20mm graded stone aggregate) as in floor laid in alternate bays, finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for Checured cement concrete tiles,of size 30 cmx30 cm x 25mm thick, with white cement and pigment , laid over cement concrete Screed bedding, laid and Jointed and pointed in neat cement slurry as in floor,including 15mm thick screed bed or bedding layer in cement mortar 1:4 , complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658- 2006 of 60 mm thickness , M-35 Grade , laid over and including 40 mm thick sand cushioning complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658- 2006 of 80 mm thickness , M-35 Grade , laid over and including 40 mm thick sand cushioning complete all as specified and directed.

Taking down cement plaster, any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

M&L for 15mm thick rendering on other faces of brick or concrete surfaces in cement mortar 1:6 finished surfaces even and smooth (without using extra cement) complete all as specified and as directed

M&L for 15mm thick rendering in two layers of 10mm thick and 5mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 finished fair and even, using water proofing compound in top layer , complete all as specified and as directed (NOTE: WPC will be measured and paid separately as "Supply only " here in after)

Supply only integral water proofing compound of approved quality complete all as specified.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of old decorated surfaces of walls and applying one coat of white wash , complete all as specified and as directed.

M&L for prepration of old decorated surfaces and applying two coats of white wash on walls, fins, facia. Chajja etc , complete all as specified and as directed.

M&L for preparation of old decorated surfaces of ceiling and applying one coat of white wash , complete all as specified and as directed.

M&L for preparation on newly plastered surfaces on wall and applying two coats of cement based paint over priming coat of alkali resistant priming paint ,complete all as specified and as directed.

M&L for preparing old painted surfaces of wall by washing, rubbing down and stopping of painted surfaces and applying a coat of cement base paint ,complete all as specified and as directed .

M&L for preparation of old decorated wooden surfaces of any description, over 10cm in width or girth, not otherwise described,, and applying one coat of synthetic enamel paint (1st quality) complete all as specified and as directed.

M&L for preparation of old decorated surfaces of AC sheet as in ceiling any description, over 10cm in width or girth, not otherwise described,, and applying one coat of synthetic enamel paint (1st quality) complete all as specified and as directed.

M&L for preparation of old decorated steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described, and applying one coat of synthetic enamel paint (1st quality) , complete all as specified and as directed.

M&L complete removal of existing treatment of surfaces of wall and applyimg two coats of cement based paint over priming coat of alkali resistant priming paint complete all as specified and directed.

S&F High density polithylene pipe ( HDPE) , 110 mm bore of pressure rating 6 Kg/ Sqcm ,fixed to walls, ceiling or in floors etc. complete all as specified and directed.

M & L for cement concrete 1:2:4 (using 20mm graded stone aggregate), as in surface channels and drains, etc., including use and waste of necessary form work, complete all as specified and as directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and as directed.

Taking out (Up-rooting) of Steel or RCC Fencing Posts or Struts of any Section, embedded in Concrete including Demolition of Cement Concrete if required including necessary Earthwork and making good disturbed Ground, complete all as specified and as directed.

M & L for precast RCC 1:2:4, type B-1 (using 20mm graded stone aggregate) as in precast fencing posts, struts etc. average sectional area exc. 100 Sqcm and not exc. 250 Sqcm with or without chamfered angles and flat, splayed, rounded or mitred tops including grouting in natural ground or cement concrete, complete all as specified and as directed. (NOTE : Reinforcement shall be measured and paid separately under relevant Items.)

S & F Galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacings,stringing, tghtening and fixing to any type of standard rails, straining bolts including securing and tying at crossings with and provision of galvanised mild steel wire,staples or steel pins etc including dismantling the old barbed wire, complete all as specified and directed. (NOTE : Each line of barbed wire shall be measured for payment. )

S & F Chain link fencing 100X100mm mesh or cages with 4mm dia mild steel galvanised wire, lapped, straining and binding with including including line wire binding wires, straining bolts etc complete all as specified and directed. (Note : MS flats iron,bolts, nuts & washers shall be measured and paid separately)

M&L mild steel round bars 10mm dia and over cut to length and bend to shape as required, including straightening etc as required in horizontal bar for securing chain link fencing complete as specified and directed.

S&F mild steel flat bar 40x6mm size or nearest suitable size as ordered in required length including drilling holes for bolts notching for wire etc. (for securing wire mesh etc) conforming to Fe-290 gde E-165 complete as specified and directed .

M&Lfor Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed the other or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nut exc., 11cm but n.exc.15cm long, dia of neck 11 mm to 15 mm, complete all as specified and directed.

M&L for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed the other or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nut exc., 5 cm but n.exc.10 cm long, dia of neck 11 mm to 15 mm, complete all as specified and directed.

M&L for preparation of new steel and iron surfaces of any description, n.exc. 10cm in width or girth, not otherwise described, and applying two coats of synthetic enamel paint (1st quality) over priming coat of red oxide zinc chrome primer complete all as specified and as directed.

M/S SANJAY ENTERPRISES

Shri Atoshe Tuccu

commercial enterprises