ADDITIONS ALTERATIONS TO EXISTING STRUCTURE AT AMBEKODAR AND PROVN OF HARD TOP AND ARMOURY, PROVISION OF HARD STANDING ADJACENT TO INCS INSTALLATION AND PROVISION OF CHAIN LINK FENCING AND ENTRANCE GATE AT MI ROOM, INS KADAMBA VANAM UNDER GE(SB)

Amount

Taking down chowkats or frames exceeding 1.5 sqm but not exceeding 4.0 sqm Each, with shutters (without taking shutters off the frames), including making good disturbed portions to match adjoining surfaces, complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5 sqm Each, with shutters (without taking shutters off the frames), including making good disturbed portions to match adjoining surfaces, complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces of walls/ceilings etc., including raking out joints, hacking for key, scrubbing down with water and removing rubbish outside MoD land, complete all as specified and directed. Note: Rate deemed to include necessary scaffolding/formwork.

Dismantling single‑layer Mangalore pattern or similar tiles in roofing including ridges/hips where provided, complete all as specified and directed.

Dismantling framed timber work in scantlings 40 sqcm and over in section, in any position, complete all as specified and directed.

M&L for framed work as in doors or gates of angle or other sections with gusset plates, rails, braces etc., prepared for hanging or sliding with and including hooks & hinges or steel hanging door fittings (exclusive of sheeting/covering, running rails and guides), including fastening and fixing, Fe‑410‑W (Gde E‑250) quality‑A, complete all as specified and directed.

M&L for 1.00 mm thick mild steel plain black sheeting for wall cladding/steel gates/door shutters etc., cut to size, holed, including fixing to wood or steel framing with round‑headed screws/clout nails/rivets with 40 mm lap joints, riveted/welded seams, mitred/turned edges as required, complete all as specified and directed.

S&F mild steel sliding door bolt, plate type, stove‑enamelled black, with bright steel bolt not less than 12 mm dia, with not less than six bolts and nuts (four on bolt plate and two on staple plate), fixed complete all as specified and directed.

S&F mild steel pressed handles, 150 mm long, oval type, stove‑enamelled black, fixed complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

M&L for anodised aluminium frames for doors, windows, ventilators and partitions with one or more rebates, including joining cleats, fixing accessories, complete all as specified and directed.

S&F anodised aluminium sections for window/ventilator shutters, sliding type without sash bars, sections weighing not less than 0.55 kg/m, including jointing cleats, glazing clips, neoprene/rubber packing, snap beading and screws, complete all as specified and directed.

S&F 4.0 mm thick sheet glass, ground/obscured/frosted (one side), ordinary quality, glazing with oil putty, in panes n.exc. 0.50 sqm Each, fixed to aluminium/wooden shutters, complete all as specified and directed.

S&F anodised aluminium grill (transparent/dyed as per IS 1868, anodic coating grade AC‑15), approved design/pattern, fixed to existing frame with CP brass/SS screws @ 200 mm c/c, including cutting to opening size for handles and fixing anodised aluminium sections around opening, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia wire with average aperture 1.40 mm, fixed with stainless steel wire staples, complete all as specified and directed.

M&L for non‑skid ceramic coloured floor tiles, 7 to 8 mm thick (square/rectangular), area of Each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, laid in floors over and including 15 mm thick screed bed in CM 1:4, set and jointed in neat cement slurry and pointed in white/coloured cement to match, complete all as specified and directed.

M&L for coloured glazed ceramic tiles, 300×450×6 to 7 mm thick, on vertical surfaces (skirting/dado/risers), set in neat cement slurry and pointed in white/coloured cement to match, over and including 10 mm thick backing coat in CM 1:3, complete all as specified and directed.

M&L for non‑skid ceramic coloured floor tiles, 7 to 8 mm thick (square/rectangular), area of Each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, laid over and including 15 mm screed bed in CM 1:4, set and jointed in neat grey cement slurry and pointed in white/coloured cement to match, complete all as specified and directed.

M&L for 18–20 mm thick granite (any type) black colour, table‑rubbed and polished, in wash‑basin counters/cooking platforms and like, set in CM 1:4 and pointed in white cement (1:2) with marble dust and pigment to match, including necessary cut‑outs and edge polishing, complete all as specified and directed.

M&L for machine‑cut Cuddapah stone slab 20–25 mm thick, laid over cement screed, set and jointed with grey cement slurry with pigment to match, including rubbing and polishing, complete all as specified and directed.

M&L for Mangalore pattern roof tiles, Class ‘A’, interlocking at side joints, laid dry as in roof covering, complete all as specified and directed.

M&L for ridge/hip tiles to suit Mangalore/roofing tiles, bedded and jointed in CM 1:6, complete all as specified and directed.

M&L for clean‑sawn second‑class softwood timber in scantlings, framed and fixed in position including necessary scaffolding/safety measures, complete all as specified and directed.

S&F 15 mm dia uPVC pressure pipes, PN‑10, fixed to walls/ceilings or laid in floors including all fittings and solvent cement joints, complete all as specified and directed.

S&F 20 mm dia uPVC pressure pipes, PN‑10, fixed to walls/ceilings or laid in floors including all fittings and solvent cement joints, complete all as specified and directed.

S&F 25 mm dia uPVC pressure pipes, PN‑10, fixed to walls/ceilings or laid in floors including all fittings and solvent cement joints, complete all as specified and directed.

S&F stop/angle valve, cast copper alloy, fancy type, chromium plated, concealed pattern with long shank and cup, screwed down high pressure, screwed both ends for 15 mm pipe, complete all as specified and directed.

S&F bib tap, cast copper alloy, chromium plated with crutch/butterfly handle, screwed down, screwed for 15 mm pipe, complete all as specified and directed.

M&L for PVC (SWR) pipes, 110 mm bore, single‑socketed with rubber ring joints, laid in trenches/in floors, complete all as specified and directed.

M&L for PVC (SWR) pipes, 75 mm bore, single‑socketed with rubber ring joints, laid in trenches/in floors, complete all as specified and directed.

S&F PVC (SWR) bend, 75 mm dia, complete all as specified and directed.

S&F PVC (SWR) bend, 110 mm dia, complete all as specified and directed.

S&F PVC (SWR) floor trap, 110 mm dia, plain, with grating and solvent‑cemented joints, complete all as specified and directed.

S&F PVC (SWR) floor trap, 75 mm dia, plain, with grating and solvent‑cemented joints, complete all as specified and directed.

S&F stainless steel sink, 1.0 mm thick, kitchen/laboratory pattern with plugs, washers and wastes, including bedding in cement mortar on dwarf walls or fixing on cantilever brackets and connecting union to pipe; overall size 495×420 mm, bowl 410×330×160 mm, complete all as specified and directed.

S&F 40mm waste fitting (coupling), brass, chromium plated, suitable for glazed ware sinks/basins, with long screwed shanks and fly nuts, flange end bedded in red lead cement, other end fixed, complete all as specified and directed.

S&F 40mm bore PVC waste pipe with approved fittings, suitable for WHB, urinals and similar fixtures, fixed in repairs, complete all as specified and directed.

S&F stainless steel plate rack of size 900 × 580 × 210 mm, securely fixed to wall with screws, complete all as specified and directed.

S&F framed work such as grills, gratings, sunshades, with ends of bars shouldered and/or riveted/welded or forged into spikes; framed guard bars, barred iron doors, ladders, framed balustrades, walkways, railings, frameworks for water tanks and similar works, conforming to Fe-410-0 or Fe-310-0, complete all as specified and directed.

S&F rotational moulded PVC triple-layered water storage tanks, capacity 1000 litres, cylindrical vertical type with closed top, ISI marked, hoisted and fixed in position including necessary fittings/ fixtures to connect with pipelines, complete all as specified and directed.

S&F second-class hardwood plain solid straight chowkats and frames, wrought, framed, rebated on solid, rounded or chamfered, joined with glue and pinned at joints, supplied and fixed, complete all as specified and directed.

S&F 30mm thick flush shutters, solid core, block board core with plywood face panels, commercial type, both sides covered with decorative laminates, supplied and fixed in chowkats, complete all as specified and directed.

S&F 30mm thick second-class hardwood glazed and skeleton shutters, open rebated, prepared to receive glass/gauze (without sash bars), edges of framing plain/chamfered/rounded, fitted with mitred beads to secure glass; members conforming to SSR Part I Sec 8, Cl 8.24(a); supplied and fixed in chowkats, divided into squares with plain/chamfered/rounded/rebated sash bars, complete all as specified and directed.

S&F 100mm butt hinges, heavy weight, cold rolled mild steel, fixed in repairs, complete all as specified and directed.

S&F aluminium alloy anodised sliding door bolt, 300mm long with hasp and staple (bolt type), fixing clips of sheet or extruded section, fixing bolts of extruded or cast aluminium alloy, stove enamelled, black finish, complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section, fixed in repairs, complete all as specified and directed.

S&F 150mm aluminium anodised handles of extruded section, fixed in repairs, complete all as specified and directed.

M&L for preparation of new wooden surfaces over 10cm width/girth, applying one coat of pink primer followed by two coats of synthetic enamel paint, complete all as specified and directed.

Excavation over areas not exceeding 1.5m in depth and getting out in hard/dense soil, including disposal of surplus soil outside MOD land, complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m deep for foundations, shafts, wells, cesspits, manholes, pier holes, etc., not exceeding 10sqm on plan, in hard/dense soil, getting out and disposing of surplus, complete all as specified and directed.

M&L for PCC 1:4:8, type D-2, using 40mm graded stone aggregate, as in foundation filling and mass concrete, laid, compacted and finished even and smooth without using extra cement, complete all as specified and directed.

M&L for precast cement concrete block masonry with solid blocks, 1:3:6 type C-1 using 20mm graded aggregate, exceeding 10cm width, set in CM 1:6, joints properly struck/pointed, including lifting/hoisting into position, complete all as specified and directed.

M&L for brickwork with subclass 'B' bricks, old size, straight or curved on plan to any radius in half-brick thick walls built in cement mortar 1:4, including raking out joints, watering, curing and scaffolding, complete all as specified and directed.

M&L for hardcore filling with broken stone or boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, well watered and rammed to a true surface, complete all as specified and directed.

M&L for RCC design mix M-30 using 20mm graded stone aggregate as in columns, pillars, and piers, including necessary formwork, compaction, curing, scaffolding, and finishing surfaces, complete all as specified and directed.

M&L for RCC design mix M-30 using 20mm graded stone aggregate as in plinth beams, beams, cantilevers, lintels, and bressummers, including necessary formwork, compaction, curing, scaffolding, and finishing surfaces, complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to required length, bent to shape including cranking, bending spirally for hooping columns, hooking ends and binding with annealed mild steel wire (not less than 0.9mm dia), complete all as specified and directed.

M&L for mild steel TMT bars 5mm to 8mm dia, cut to required length, bent to shape including cranking, bending spirally for hooping columns, hooking ends and binding with annealed mild steel wire (not less than 0.9mm dia), complete all as specified and directed.

Returning, filling in trenches, including spreading, levelling, watering, and well ramming in layers not exceeding 25cm thick, in hard/dense soil, complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of brickwork or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement, including curing, complete all as specified and directed.

S&F rolled steel sections as in main and cross beams, hip and jack rafters, purlins, running rails and guides for sliding doors, fixed with angle cleats or connecting plates, conforming to Fe-410-W (Grade E-250) quality-A, complete all as specified and directed.

S&F wind ties for roof trusses/ posts and struts in fencing including cutting to shape, drilling holes, securing bolts/ notching for wire and similar work, conforming to Fe-290 Grade E-165, complete all as specified and directed.

M&L for pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 MPa as in roof covering/cladding to walls, fixed with self-tapping screws, complete all as specified and directed.

S&F solid PVC door frame of size 50mm × 47mm, made out of 5mm wood grain printed PVC sheet reinforced with MS square tube and edges painted to match with printed sheet, complete all as specified in manufacturer's drawing and directed.

S&F factory made solid panel PVC door shutter 30mm thick (styled), consisting of MS tube frame for top & bottom rails covered with heat moulded PVC ‘C’ channel of 5mm thickness, decorative PVC sheet panelling fitted inside frame, edges jointed/sealed with solvent cement, fixed in PVC frame at site, complete all as specified in manufacturer's drawing and directed.

S&F plastic water closet seat and cover, closed pattern with flat bottom, suitable for pedestal/semi-pedestal pattern WCs, fixed with mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

S&F 10 litre capacity PVC valveless syphonic action type flushing cistern, high or low level, white, with inlet ball valve, float, handle and including brackets, complete all as specified and directed.

S&F 15 mm dia PVC connection of length 450mm complete all as specified and directed.

S&F flush pipe, PVC, 32mm dia, for low level flushing cistern, including necessary joints, cones and rubber fittings for connection to WC pan, complete all as specified and directed.

S&F Health faucet (ABS body), chromium plated, suitable for 15mm dia pipe, with 1.25m long flexible tube and ABS wall hook, including connection and fixing in position, complete all as specified and directed.

S&F two way bib cock with two lever and wall flage chromium plated brass, screwed for iron pipe 15mm bore complete all as specified and directed

S&F wash basins vitreous china, flat back size 550x400 mm white excluding taps,waste chain and plug and porcelain stopper but including barackets all as directed.

Supply and fix vitreous china urinal, half stall (back or corner wall type), including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing with brass screws (60mm long), and pointing around urinal back in cement, complete all as specified and directed.

Supply and fix self-closing taps, cast copper alloy, chromium plated, screwed for 15mm bore iron pipe, fixed for urinals in repairs, complete all as specified and directed.

Supply and fix 32mm size waste fitting (coupling) brass, chromium plated, for glazed ware sinks, basins, etc., with long screwed shanks, fly nuts, flange end bedded in red lead cement, and other end fixed, complete all as specified and directed.

Supply and fix 32mm dia PVC waste pipe suitable for wash hand basins and urinals, fixed in repairs, complete all as specified and directed.

Supply and fix brass chromium plated towel rail, 20mm dia, 'D' type, 600mm long between flanges, fixed in repairs, complete all as specified and directed.

Supply and fix brass chromium plated shower rose with or without swivel joints, fancy type, 125mm size, suitable for 15mm bore GI pipe, complete all as specified and directed.

Supply and fix brass chromium plated mixer for mixing hot and cold water, screwed down for 15mm bore iron pipe, complete all as specified and directed.

Material and labour for preparation of new plastered/ decorated wall surfaces, applying two coats of oil bound distemper over one coat of alkaline-resistant primer over a coat of 3mm thick wall care putty, including scaffolding and safety measures, complete all as specified and directed.

M&L for preparation of old plastered/ decorated wall surfaces including complete removal of existing treatment by brooming down, steel wire brushing, scraping smoke soot, moulds, moss and efflorescent salts, treating oil and greasy spots, and applying two coats of oil bound distemper over a coat of alkali resistant primer, including necessary scaffolding and safety measures, complete all as specified and directed .

M&L for preparation of old painted wooden surfaces of any description, over 10 cm in width or girth, and applying two coats of synthetic enamel paint, including necessary scaffolding and safety measures, complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 using 20mm graded stone aggregate, as in hardstanding/plinth protection, finished even and smooth without using extra cement, complete all as specified and directed.

S&F 20mm dia stainless steel curtain rod or similar articles, fixed complete all as specified and as directed

S&F stainless steel decorative type brackets suitable for 20mm dia curtain rods or similar articles, fixed complete all as specified and as directed.

M&L for providing and injecting chemical emulsion for post-construction anti-termite treatment along external wall below concrete/masonry apron at 2.25 litres per linear metre, including drilling holes, plugging holes with cement mortar, and matching existing surface, complete all as specified and directed.

M&L for providing and injecting chemical emulsion for post-construction anti-termite treatment at points of contact of wood with masonry/concrete surfaces at 0.5 litres per hole, including drilling 6mm dia holes at downward 45° angle at 150mm c/c, plugging with cement mortar (1:2) to match existing surface, complete all as specified and directed.

S&F readymade pulley-operated clothes drying system (7 feet), consisting of anodised aluminium pipes (22mm OD, 19.8mm ID), derlin pulleys with rope guide, 24'' channel with adjustable pipe spacing, locking system, HDPE double-core rope (4mm dia), mounted with self-tapping screws and all accessories, fixed to ceiling, complete all as specified and directed.

M&L for preparation of old plastered/decorated wall surfaces, including complete removal of existing treatment by brooming down, steel wire brushing, scraping soot, moulds, moss and efflorescent salts, treating oil and greasy spots, and applying one coat of exterior-grade acrylic emulsion paint, including necessary scaffolding and safety measures, complete all as specified and directed.

M&L for moorum/red bajri filling under floors or in foundations/ pavings, including spreading, levelling, watering and well ramming in layers not exceeding 15 cm thick, complete all as specified and directed

M&L for 100mm thick plain cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base / sub floors etc., complete all as specified and directed.

M&L for 100mm thick plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate, finished even and smooth without using extra cement as laid in alternate panels in flooring complete all as specified and directed.

Supply only glass dividing strips 3 mm thick and 38 mm wide, inserted in position to conform to design, complete all as specified and directed.

Removing surplus excavated material/ soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point, complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m in depth and 1.5 m in width, getting out in soft/loose soil, including removal of surplus soil, complete all as specified and directed.

M&L for RCC design mix M-30, using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, basement slabs, under-reamed piles, and mass concrete, complete all as specified and directed.

M&L for RCC design mix M-30, using 20 mm graded stone aggregate as in columns, pillars, piers, posts, and struts, complete all as specified and directed.

Use and waste formwork to sides of concrete foundations, footings, bases of columns, and plinth beams, finished rough to flat surface, complete all as specified and directed.

Use and waste formwork to sides of pillars, posts, struts, and columns, finished fair, square or rectangular on plan, complete all as specified and directed.

M&L for mild steel reinforcement, 5 mm dia and over but not exceeding 10 mm dia, cut to length, bent to shape as stirrups, including hooking ends and binding with annealed MS wire not less than 0.9 mm dia, complete all as specified and directed.

Excavation in post holes (or similar holes) in soft/loose soil Each not exceeding 0.50 cum, getting out, returning, filling in, and ramming earth, complete all as specified and directed.

M&L for plain cement concrete 1:3:6, type C-2, using 40 mm graded stone aggregate as in foundations, filling, and mass concrete, complete all as specified and directed.

Supply only, chain link MS galvanized fencing, of any size or type, delivered at site, complete all as specified and directed.

Fixing only chain link fencing, including line wires, mesh of any size or type, with rails, straining bolts, and binding wire, complete all as specified and directed.

S&F rolled mild steel roof trusses (framed), trussed purlins, rails, fastenings, and heavy brackets framing (beam, tee, angle, channel, or flat sections) including distance pieces, cleats, etc., conforming to Fe-290 (Grade E-165), complete all as specified and directed.

Supply & Laying including jointing, testing and commissioning in repair of 4 core 10.00 Sqmm XLPE insulated, armoured, heavy duty, LT UG electric cable with aluminum conductor 1100 volt grade including provision of lugs, glands etc fixed on wall/pole/ hard surface or drawn through GI pipe complete all as specified and directed.

Supply and lay GI tubing, 'light grade' of size 50 mm ,with all fittings as in cable protection, laid in trenches or laid on hard land with all accessories complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 600 × 600 × 6 mm thick, buried directly in ground not less than 2.25 m below normal ground level with top edge of plate not less than 1.5 m below ground level, connected to galvanized iron wire 4 mm as earthing lead, by means of GI bolts, nuts, checknuts and washers, the earth lead protected by GI medium grade pipe 40 mm bore, including PCC (1:2:4) chamber with RCC cover slab (50 mm thick) reinforced with 8 mm dia TMT bars @ 140 mm c/c both ways, angle iron frame 40 × 40 × 6 mm with 6 mm dia MS bar handle, GI watering pipe 20 mm bore light grade with funnel and wire mesh, filling with charcoal and common salt in alternate 150 mm layers all around the electrode, excavation and earthwork in any type of soil, returning filling, removal of surplus soil to a distance not exceeding 50 m, including connection to test point and testing on completion, complete all as specified and directed, and as per Plate No. 3 of SSR Part-I. Note:- (i) Earth strip and its protection pipe up to and including 7.5 m from the top of earth electrode are included in this item.

Supply, installation, and testing of diesel engine pump set, horizontal end-suction, centrifugal type, conforming to IS:12469–1988, complete with cast iron casing, bronze impeller, and stainless steel shaft mounted on heavy-duty bearings, suitable for continuous operation within a range of 0% to 150% of rated capacity, designed for 410–440 V, 3-phase, 50 Hz AC supply. Pump of 30 m head, 5 HP capacity, to be installed on suitable PCC foundation with clamps duly grouted, including alignment, testing, and commissioning, complete all as specified and directed.

Supply and laying of GI tubing, 'medium grade' of size 50 mm with all fittings as above ground hard rock surface with suitable clapping arrangement complete all as specified and directed .

Supply and fix Foot Valve 50 mm (2”) dia conforming to IS 4038, all as specified and directed .

Supply and fix sluice Valve Class PN 1.6 of size 50 mm all as specified and directed .

Supply and fix NRV Class PN 1.6 of size 50 mm all as specified and directed .

Supply, installation, testing & commissioning of analog addressable fire alarm control panel complying with BS EN 54, single loop panel of capacity from 99 detectors & 99 modules up to 200 detectors and modules, expandable up to 6 loops, with LCD display and required power supply & batteries for 24 hours in normal operation and 15 minutes in fire condition, complete all as specified and directed. Make: Edward EST-3/ Notifier or equivalent approved make.

Supply, installation, testing & commissioning of network card to connect panels and repeater panel through RS-485 data configurable as master/slave, multiple master/slave, and peer-to-peer networking, complete all as specified and directed . Make: Edward EST-3/ Notifier or equivalent approved make

Supply and fix detectors complying with and type certified to EN-45, addressable type multi-sensor detector with heat and smoke combination as per IS:11360, complete all as specified and directed.

Supply and fix addressable manual call point, resettable type, complete all as specified and directed.

Supply and fix addressable electronic sounder-cum-strobe, complete all as specified and directed.

Material and labour for 2 core, 1.5 Sqmm, multi-stranded copper armoured cable, complete all as specified and directed

Material and labour for fire alarm sounders/sirens, electronic type, horizontal, two-stage, continuous normal operation for at least 50 minutes, with sound level 65 dB to 120 dB measured at 1.5 mtr, with sound output variation of ±5 dB over 500 mtr range, complete all as specified and directed.

Supply and fix addressable control module, complete all as specified and directed.

Supply and lay GI tubing, 'light grade' of size 25 mm with all fittings as in cable protection, laid in trenches all as speciefied and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody and making good disturbed surfaces of walls, floors, etc.

M&L in replacement of point wiring with 2 runs of 1.5 Sqmm (nominal area) single-core, PVC insulated, sheathed, 1100 V grade, multi-stranded copper conductor, FRLS grade, ISI marked, conforming to IS:694 (Part II), drawn through and including suitable size rigid non-metallic PVC conduit fixed on surface with all accessories. Work includes provision of suitably sized sunken pressed steel or cast iron terminal boxes with 3 mm thick plastic laminated sheet top cover, fixed flush to wall with brass screws and cup washers, for mounting switches, sockets, fan regulators, etc., including 1 run of 1.5 Sqmm single-core, PVC insulated, sheathed, multi-stranded copper conductor cable as earth continuity conductor, connected to metallic body of luminaire/fan at one end and to common earth dolly at the other end, for one light/fan point, complete all as specified and directed.

M&L for point wiring with 2 runs of 1.5 Sqmm (nominal area) single-core, PVC insulated, sheathed, 1100 V grade, multi-stranded copper conductor, FRLS grade, ISI marked, conforming to IS:694 (Part II), drawn through and including suitable size rigid non-metallic PVC conduit fixed on surface with all accessories. Work includes provision of suitably sized sunken pressed steel or cast iron terminal boxes with 3 mm thick plastic laminated sheet top cover, fixed flush to wall with brass screws and cup washers, for mounting switches, sockets, fan regulators, etc., including 1 run of 1.5 Sqmm single-core, PVC insulated, sheathed, multi-stranded copper conductor cable as earth continuity conductor, connected to metallic body of luminaire/fan at one end and to common earth dolly at the other end, for one light/fan point, complete all as specified and directed.

M&L for point wiring with 4.0 Sqmm single-core, PVC insulated and sheathed, 1100 V grade, stranded copper conductor, FRLS grade, ISI marked, conforming to IS 694 (Part II), drawn through and including suitable size rigid PVC conduit fixed on surface (walls, ceilings, floors, or roofs) with all necessary accessories, complete with 4.0 Sqmm single-core PVC insulated and sheathed stranded copper conductor cable as earth continuity conductor, connected to metallic body of luminaire at one end and to common earth dolly at the other end, for one independent 3-pin socket outlet, 15 Amps capacity, complete all as specified and directed.

Dismantling and taking down fluorescent tube light single/double of any wattage or size street light fittings all as specified and directed.

S&F integral sleek extruded polycarbonate batten for LED tube light with white acrylic cover suitable for upto 1x20 watts LED tube light complete all as specified & directed.

Supply and fix LED tube rod 20 Watt, 6500 K, 1200mm long complete all as specified and directed .

Supply and fix, flameproof LED light fitting 1x16 watt, CMRI certified, suitable for gas/vapour group II A & III B, Zone 1 & 2, IP65 protection, with die-cast aluminium housing, heat-resistant toughened glass, LED tube light fixtures, driver, holders, connectors, prewired, and connected with three-core flexible copper conductor cable of suitable size, complete all as specified and directed.

Supply and fixing wall-mounted fan, AC single-phase, 230 V, sweep 400 mm, heavy-duty, double-string type, supplied in dismantled condition, assembled at site, including making necessary electrical connections, testing, and commissioning, complete all as specified and directed. Make : Bajaj Esteem or equivalent in Havells, crompton greves.

Supply and fixing ceiling fan, 230 V, sweep 1200 mm, complete with blades, down rod, electronic regulator, and all accessories, energy efficient with brushless direct current (BLDC) motor, five star BEE rated, delivering minimum air output of 210 CMM with service value not less than 6.00, complete all as specified and directed.

Supply and fix switch piano 6 amps one way flush type , all as specified and directed.

Supply and fix in repair switch piano 6 amps one way flush type, all as specified and directed.

Supply and fix socket outlet 3 pin, 6 Amps flush type, ISI marked, all as specified and directed.

Supply and fix switch socket combination 16A 3 pin, flush type, ISI marked, all as specified and directed.

Supply and fixing LED street light fitting, 60 Watt, 230 V AC, outdoor type, with high-pressure die-cast aluminium housing, impact- and corrosion-resistant, heat-resistant glass cover, complete with inbuilt driver, lamp bracket, and thermal management system in multiple optics, having ingress protection of IP65/IP66, suitable for outdoor illumination, complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 450 mm sweep with, blades, and frame and louvers complete all as specified and directed .

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300 mm sweep with, blades, and frame and louvers complete all as specified and directed .

Supply and Fixing of Ceiling rose, single phase, PVC or polycarbonate with isolated body at the locations required for fans or lights located on the ceiling 10 feet above the ground complete all as specified and directed .

M&L for sub-main wiring with proper colour coding using FR-LS PVC insulated, unsheathed, multi-stranded, single core copper conductor cable comprising two runs of 6.0 Sqmm for phase and neutral and one run of 6.0 Sqmm for earth wire, drawn through and including PVC casing and capping with all fittings such as tees, bends, junction boxes/terminal boxes fixed on wall/ground/ceiling, and connected complete all as specified and directed. Note: (i) Phase shall be of Red/ Yellow/ Blue, neutral shall be of black and earthing wire shall be of green colour as per standards (ii) Two runs of cable for phase/ neutral and one run of cable for earth shall be measured and paid as one unit length.

Supply and fixing sheet metal enclosure MCB DB SPN 8 ways double door type with suitable bus bar complete all as specified and directed.

Supply and fixing in repair sheet metal enclosure MCB DB SPN 8 ways double door type with suitable bus bar complete all as specified and directed.

Supply and fixing sheet metal enclosure MCB DB SPN 12 ways double door type with suitable bus bar complete all as specified and directed.

Supply and fixing MCB SP, 6 to 32 Amps, ''C'' series 240 Volts, single phase, 10 KA breaking capacity complete all as specified and directed.

Supply and fixing in repair MCB SP, 6 to 32 Amps, ''C'' series 240 Volts, single phase, 10 KA breaking capacity complete all as specified and directed.

Supply and fixing MCB SPN, 32 Amps, ''C'' series 240 Volts, single phase, 10 KA breaking capacity complete all as specified and directed.

Supply and fixing in repair MCB SPN, 32 Amps, ''C'' series 240 Volts, single phase, 10 KA breaking capacity complete all as specified and directed.

Supply and fixing MCB TPN, 32 Amps, ''C'' series 240 Volts, single phase, 10 KA breaking capacity complete all as specified and directed.

ABDUL RAHIM (BID ID -3472739)