CA NO CWE/CHM-58/2019-20 RENEWAL OF FURNITURE AGAINST SURVEYED OFF FURNITURE AT BSO GE CHANDIMANDIR

Amount

PART I WOODEN FURNITURE

TABLE PEG (DRG NO FD-277) Ist class seasoned teak wood shall be used through out. Top shall be made out of pre-laminated particle board 18/19 mm thick ISI marked exterior gde. 6 mm thick teak wood beading shall be used all around at top. Rubber PVC shoes shall be provided at the bottom of legs duly screwed. All wood surfaces shall be French polished to a glossy finish . Rest all as per drg complete all as shown as Drg No FD-277 complete all as specified and directed.

CHAIR DINING (DRG NO FD-1105/279) Teak wood Ist class shall be used through out . Canning shall be done/woven in Godrej pattern with cane plastic 2 mm wide and 3 mm wide for border. Make of cane shall be of Premier/ Usha. All exposed surfaces shall be french polished to a glossy finish. Rest all as per drg No FD-1105 complete all as specified and directed.

SIDE BOARD (DRG NO FD-241) All side shall be made out of Prelaminated Perticale board 18/19 mm thick. Top shall be made Prelaminated Perticale board 18/19 mm thick . All wood surfaces exposed to view shall be French polished with high gloss finish. Complete prelaminated perticale board 18/19mm thick.

TABLE WRITING (DRG NO FD-275) (a) All wood work shall be of 1st class hard wood (Teak). (b) Irrespective of what is shown in the drawing top of table shall be of 18MM thick Pre-laminated particle board exteir grade as specified here-in-before 4MM thick teak wood edging shall be provided all-round. (c) Front of drawer and shutter of cabinet ( below drawer) shall be of 18MM thick Prelaminated particles board ( Prelaminated perticale board exteir grade as speicified here-in-before sides, bottom and shelf of cabinet shall be of 18 MM prelaminate perticale board as per drg . (d) Bottom of drawer and back cabinet shall be of 6MM thick commercial plywood as per IS - 303. (e) All exposed surfaces of timber & wood based surfaces ( except laminated surfaces) and prelaminated particle board and 4mm teak wood bedding shall be French polished. (f) All joints fixing shall be done in accordance with standard workmanship and specification. (g) Rest all as shown on drawing and as directed by GE/Engr-in-charge.

SOFA SET 4 SEATER WITH CUSHION (DRG NO FD-373) The set shall consist four small pieces of one seat . Timber work shall be of Ist class seasoned teak wood. Foam shall be 100 mm thick cushion of ‘cool’ foam of 40 density of size 530mmx500mm covered with best quality tapestry cloth rate not les than Rs. 450 / of approved make. All wood surfaces exposed to view shall be French polished. Rest all as per drg No FD-373 complete all as specified and directed.

TEAPOY WOODEN SM TOP (DRG NO FD-278) All as shown on drg. Overall size of peg table shall be 600mm long, 450mm wide 540mm high. All wood shall be of Ist class teak wood. Top of table shall be made out of prelaminated particle board 18mm thick exterior grade and 4mm thick teak wood beading shall be provided all round the table irrespective of what is shown on drg and all as per drg No FD-278 complete all as specified and directed.

HAT STAND WITH MIRROR (DRG NO FD-233) shall be all as shown on drawing No FD-233.Over all size shall be 1000 mm long and 710 mm high . All wood shall be teak wood well seasoned free from cracks and knots. (a) The frame of Hat stand shall be provided with 4 mm one side teak face ply . (b) The back of Hat Stand shall be provided with 4 mm thick commercial plywood . A Mirror of 440 mm high and 300 mm wide with 6 mm thickness of ATUL/MODIGUARD or GOLDEN FISH . Free from distortion and defect shall be provided on right hand side of Hat Stand with 10 mm x 12 mm in sec teak wood beading al-round the mirror. (c) Four brass pegs of 75 mm wide and 120 mm high of shape as approved by Engr-In-Charge shall be provided with 6 mm thick brass screws / nut or bolt . Two key plate of mild steel sheet 3 mm thick flat iron with key hole shall be provided to two top corners at the back of Hat Stand. (d) All wood and teak ply surface , exposed to view when placed in position shall be given high gloss french polish with lacquer finish after preapration of surface . (e) All steel surface shall be painted with two coats of black paint over a coat of primer after prepration of surface . Brass pegs shall have shining surface and remain untreated irrespective of what shown on drawing. Rest all as shown on drawing and as directed by GE/Engr-in-charge.

TABLE DRESSING LADIES WITH MIRROR (DRG NO FD-251) All wood shall be of Ist class hard wood teak .The bottom side of dressing table shall be of 18/19 mm thick prelaminate perticale board & prelaminated particle board 18/19mm on other side. Top shall be of/18/19 mm thick prelaminated particle board Frame work of mirror shall be of Ist class teak wood back shall be of ply wood 6 mm commercial ISI marked, Mirror shall be 5 mm thick ISI marked. Make of mirror shall be Atul/Modi. All wooden surfaces shall be French polished to a glossy finish nad all as per drg No FD-251 complete all as specified and directed.

TABLE CENTRE (DRG NO FD-274) Ist class seasoned teak wood shall be used through out. Top shall be made out of pre-laminated particle board 18/19 mm thick ISI marked exterior gde. 6 mm thick teak wood beading shall be used all around at top. Rubber PVC shoes shall be provided at the bottom of legs duly screwed. All wood surfaces shall be French polished to a glossy finish and all as per drg No FD-274 complete all as specified and directed.

TABLE DINING 6 PERS (DRG NO FD-272) All as shown on drg. Over all size shall be 1500 mm long, 900 mm wide and 760 mm high. Frame shall be made out of teak wood through out. Top shall be made out of 18 mm pre-laminated particle board ISI marked one side teak face. All wooden portion shall be finished with French polish.

CHAIR DINING WITH CUSHION (DRG NO FD/MAP/E6/10) (a) All wood work shall be of 1st class hard wood (Teak). (b) Seat shall be 75 MM thick foam of 32 density covered with good quality tapestry cloth (cost of cloth not less than Rs 450/- per meter) as approved by GE over 12MM thick commercial plywood as per IS-303. (c) Nylon buffers of appropriate size shall be screwed to the bottom of each leg. (d) All exposed surfaces of timber and plywood shall be french polished. (e) All joint fixing shall be done in accordance with standard workmanship and specification. (f) Rest all as shown on drawing.

TABLE DRESSING GENTS WITH MIRROR (DRG NO FD-230) All wood shall be of Ist class hard wood teak .The bottom side of dressing table shall be of 18/19 mm thick prelaminated pertical board. Top shall be of 19 mm thick commercial particle board . Frame work of mirror shall be of Ist class teak wood back shall be of ply wood 6 mm commercial ISI marked, Mirror shall be 5 mm thick ISI marked. Make of mirror shall be Atul/Modi. All wooden surfaces shall be French polished to a glossy finish and all as per drg No FD-230 complete all as specified and directed.

TABLE DINING 1200x900x760mm (DRG NO FD-273) All as shown on drg. Over all size shall be 1500 mm long, 900 mm wide and 760 mm high. Frame shall be made out of teak wood through out. Top shall be made out of 18 mm pre-laminated particle board ISI marked one side teak face. All wooden portion shall be finished with French polish.

SOFA SET 5 SEATER WITH CUSHION (DRG NO FD-373) The set shall consist of one long piece of three seat and two small pieces of one seat each. . Timber work shall be of Ist class seasoned teak wood. Foam shall be 100 mm thick cushion of ‘cool’ foam of 40 density of size 550 mmx525mmx100mm covered with best quality tapestry cloth rate not les than Rs. 450. of approved make. All wood surfaces exposed to view shall be French polished and all as per drg No FD-373 complete all as specified and directed.

TABLE 3'x3' WOODEN as per drawing and approved by GE/Engineer-in-Chief.

PART II STEEL FURNITURE

ALMIRAH LARGE STEEL (DRG No FD-1031) (i) Steel Almirah (body, shutter, drawer, locker, vertical partitions and shelves) shall be made out of 1 mm thick mild steel sheet all as shown on drawings. (ii) All joints/welding/fixing shall be done all as shown on drawings and with standard workmanship. (iii) Almirah shall be provided with three way locking device as per ‘Godrej’ pattern .The handle shall be made out of steel chrominium plated as per ‘Godrej’ pattern. 4 lever brass lock 65 mm size shall be provided as per Godrej pattern, of make GODREJ, LINK, HARRISON. (iv) Almirah shall be provided with three numbers adjustable shelves with four compartments (v) One steel chrominium plated handle shall be provided to the drawer. (vi) All steel surfaces internally and externally shall be painted with two coats of synthetic enamel paint (olive green) with spray gun over a coat of zinc chromate steel primer. (vii) The welding joints shall be filed smooth before application of primer. The surface shall be thoroughly cleaned and prepared prior to application of paint. (viii) Rest all as shown on drawing.

Almirah Mess Utensil (DRG NO FD-93) As per drawing and approved by GE/Engineer-in-Chief.

BOOK CASE STEEL (DRG NO FD-1028) Item to be fabricated as per drg. Overall size shall be 840mm long, 310mm wide and 1675mm, cold rolled, cold annealed MS sheet 1mm thick to be used for channel base, top, sides, back, bottom, front and shelves. The book case shall be provided with four compartments of equal size. The shutters of each compartment shall be open towards top and slide into the depth of the book case. Two steel handles of 100mm shall be provided to each shutter of the compartment. The locking device shall be provided to each compartment. All joints and welding, fixting shall be done in accordance with standard workmanship. rest all as shown on drawing.

ALMIRAH STEEL (MEDIUM) (i) Steel Almirah (body, shutter, drawer, locker, vertical partitions and shelves) shall be made out of 1mm MS plain black sheet all as shown on drawings. (ii) All joints/welding/fixing shall be done all as shown on drawings and with standard workmanship. (iii) Almirah shall be provided with three way locking device as per ‘Godrej’ pattern .The handle shall be made out of steel chrominium plated as per ‘Godrej’ pattern. Six lever brass lock shall be provided as per Godrej pattern. (iv) One steel chrominium plated handle shall be provided to the drawer. (v) Locker of the almirah shall be provided with locking arrangement operated with handle as per Godrej pattern. (vi) All steel surfaces internally and externally shall be painted with two coats of synthetic enamelled paint (silver grey colour) with spray gun over a coat of zinc chromate steel primer. (vii) The welding joints shall be filed smooth before application of primer. The surface shall be thoroughly cleaned and prepared prior to application of paint . (xiii) Rest all as shown on drawing.

TEAPOY VERNDAH (DRG NO FD/E6/MAP/17) (i) Frame, stiffeners, legs ,etc. shall be made of 18mm square MS pipe of thickness 18 gauge. (ii) Top of Teapoy shall be of 18mm thick Prelaminated particle board (one side decorative finish shade as approved by GE and other side white balancing lamination (iii) Base tray made with 5mm dia mild steel wire/rod shall be provided (iv) 4mm thick teak wood edging shall be provided alround. (v) FINISHES: All steel surfaces, exposed to view when placed in position shall be given two coats of enamel paint over a coat of primer with spray machine after preparation of surface. (vi) Rest all as shown on drawing

CHAIR WRITING MAP STEEL (DRG NO FD/MAP/E6/12 As per drawing and approved by GE/Engineer-in-Chief.

TABLE 900x900x760mm W/O DRAWER (DRG NO FD-1009) DIMENSION:Overall size shall be 900mlong,900mm wide and 760mm high. DESCRIPTION:Steel frame shall be of 800 mm X800mm X742mm . Four legs shall be of 25mm square mild steel tube of wall thickness 1.6mm. Legs shall be joined together with the top rails of 25mm square mild steel tube of thickness 1.6mm. Top of the table shall be of 18mm thick pre-laminated MDF board and provided with 4mm teak wood edging all round the top of table. Hard rubber/PVC toes shall be provided to bottom of legs. FINISH: All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg.

BED MAP STEEL (DRG NO FD/E6/MAP/08(R) (i) Bed hard shall be manufactured all as per details shown in the drawing. All dimensions, shape and size shall be followed as per drawing. (ii) All square and rectangular MS pipes shall be of thickness 18 gauge. (iii) Top of bed shall be of 12mm thick commercial plywood (unpolished) as per IS-303. (iv) Head board and foot board shall be of 18mm thick Prelaminated particle board (both side decorative finish shade as approved by GE ) as specified here-in- before, screwed to MS strip all as per details shown in drawing. Standard PVC edging (minimum thickness 1.6mm) shall be provided alround in Head board and foot board . (v) Hard rubber/PVC shoe shall be provided to the bottom of each leg. (vi) All exposed steel surfaces shall be painted with two coats of synthetic enamel olive green paint over a coat of zinc chromate steel primer. The welding joints shall be filed smooth before application of primer. The surface shall be thoroughly cleaned and prepared prior to application of paint . (vii) Rest all as shown on drawing.

PART III TRADE PATTERN FURNITURE

RECEPTICAL PVC (DRG NO FD/E6/MAP/13) (a) Recepticle shall be of covered plastic container of 75 ltr capacity made with thick polymer plastic alongwith lid and handles. Recepticle shall be of bright colours ie. Red,Green,Blue etc. (b) Recepticle shall be of make: Blow plast/Neel Kamal/ Supreme/ Cello/Polyset, as approved by GE.

BATH MAT PVC (DRG NO FD/MAP/E6/07) (i) All PVC work shall be of standard class PVC. All dimensions shape and size shall be followed as per drg. (ii) PVC Bath Mat shall be of make blow plast/Neel Kamal/Supreme/Cello/Polyset/Brite/syntex. (iii) Hard rubber shoe shall be provided to the bottom of each leg. (iv) Rest all as shown on drawing No FD/MAP/07 complete all as specified and directed.

CHAIR COMPUTER (DRG NO FD/E6/MAP/01) (a) Chair computer shall be manufacured all as per details shown in the drawing. All dimensions shape and size shall be followed as per drawing. (b) Chair computer shall be of Make/manufacuturer M/S Godrej & Boyce Mfg Co. Ltd/Usha lexus/Durain. (c) The colour, texture and shade of fabric shall be got approved from GE. (d) All joint fixing shall be done in accordance with standard workmanship and specifcation. (e) Rest all as shown on drawing and as directed by GE/Engr-in-charge.

Shyam And Co.

singh traders

B K CONTRACTORS

ASHOKA FURNITURES

Capital Construction Company